IJRET: International Journal of Research in Engineering and Technology

eISSN: 2319-1163 | pISSN: 2321-7308

STATISTICAL PROCESS CONTROL

Ved Parkash1, Deepak Kumar2, Rakesh Rajoria3
1

Department of Mechanical Engineering, Swami Keshvanand Institute of Technology,

Ramnagaria, Jagatpura, jaipur 302025, Vedverma1988@gmail.com
2
Department of Mechanical Engineering, Poornima College of Engineering, Jaipur 302025
3
Service Engineer, Lucas Indian Service Limited, Jaipur

Abstract
The deployment of statistical process control (SPC) in manufacturing environments is a prominent global phenomenon. Statistical
Process Control is largely used in industries for monitoring the process parameters. It is a standard method for visualizing and
controlling processes on the basis of measurements of randomly selected samples. The decisions about what needs to be improved, the
possible methods to improve it, and the steps to take after getting results from the charts are all made by humans and based on
wisdom and experience. The statistical process control described in this paper gives the details about the SPC, its advantages and
limitation, applications and information regarding the control charts.

Keywords: Statistical Process Control, Control chart, 5Ms, Capability Indices.

---------------------------------------------------------------------***------------------------------------------------------------------------1. INTRODUCTION:

2.3 Quality-Capable Process

Statistical Process Control (SPC) is a procedure for open or

closed loop control of manufacturing processes based on
statistical methods. This procedure helps in monitoring the
process behavior. It is a standard method for visualizing and
controlling processes on the basis of measurements of
randomly selected samples.

A process having capability to completely fulfill the specified

requirements.

The main objective of SPC is to ensure that the planned

process output is achieved and the related customer
requirements are fulfilled. In this process control, randomly
some parts are taken from the manufacturing process and then
their characteristics are measured and shown on the control
charts. Statistical indicators are determined from the
measurements and used to evaluate the current status of the
process. If required, the process is rectified with some
appropriate actions.

2.4 Shewhart quality control chart

It is used for monitoring a parameter of the probability
distribution of characteristics, in order to determine whether
the parameter varies from a specified value.

2.5 Capability and Performance Indices

Quantitative measures for evaluating capability include the
machine and process capability or process performance
indices. These must achieve or surpass the specified minimum
values. The minimum requirements for process capability or
performance may exist for special characteristics, or may be
specified internally on a product-by-product basis.

2. TERMS USED FOR SPC:

2.6 Machine Capability Study

2.1 Process

The machine capability study is a short-term study with the

sole aim of discovering the machine-specific effects on the
production process.

A process is a series of activities which transforms the raw

materials or pre-machined parts or components into a finished
product.
The definition is as follows: Set of interrelated or interacting
activities which transforms inputs into outputs.

2.2 Stable Process

2.7 Process Capability Study

The process capability study is a longer-term study. In
addition to variation arising from the machine, all other
external factors that influence the production process over a
longer operating time must be taken into account.

Process which is in a state of statistics control. In this type, the

location and variation of the process characteristics are stable
over the time.

__________________________________________________________________________________________
Volume: 02 Issue: 08 | Aug-2013, Available @ http://www.ijret.org

70

IJRET: International Journal of Research in Engineering and Technology

2.8 Capability Indices Cmk, Cpk and Performance

Index Ppk

In accordance with the QS-9000 reference documents, the

term Cpk must only be used for a stable process. A process is
stable if the following synonymous statements apply to it:
Mean and variance are constant.
No systematic variations of the mean such as trend,
batch-to-batch variation, etc., occur.
There is no significant difference between sample
variation and total variation.
Every sample represents the location and variation of
the total process.

2.9 Machine Capability Study:

A machine capability study concentrates exclusively the
characteristics of the machine, i.e. to the extent possible, the
influence or effects of variables external to the machine
(noise factors) are minimized. Some examples of variation
sources are:

Man:

Personnel
Shift changes

Machine:

Speed
Feed rate
Tools
Cycle times
Coolant flow rate and temperature
Pressures
Current (in the case of welding equipment)
Power (in the case of laser welding)
Change status (in the case of optimization measures)

Material:

Semi-finished products, rough parts or blanks from

different lots or Manufacturers

eISSN: 2319-1163 | pISSN: 2321-7308

Location of the machining facility in the building

(storey)
Unusual events

It is expected that only the machine's inherent sources of

variation will affect the product and its characteristics if these
possible influences are kept constant. In cases where this is not
possible, the changes in the external influencing factors should
be documented in the record of test results. This information
can be used as the basis for optimization measures if the
capability specifications are not met.

3. TOOLS FOR SPC:

Seven basic tools for quality improvement are used for
statistical process control as given below.
Check sheet
Run chart
Histogram
Pareto chart
Scatter diagram/chart
Cause and effect or fishbone diagram
Control chart

4. CONTROL CHART:
Control chart is the most successful statistical process control
tool, developed by Walter Andrew Shewhart in early 1920s.
Control charts may be used to monitor a process to determine
whether or not the process is in statistical control, to evaluate a
process and determine normal statistical control parameters
and to identify area of improvement in process.
Control charts attempt to differentiate between the types of
process variation:
Common cause variation: It is intrinsic to the process and
will always be presents. It is also known as Chance cause
variation.
Special cause variation: Special cause variation stems from
external source and shows that the process is out of statistical
control. It is also known as assignable cause variation or Out
of Statistical Control.

Other Process monitoring tools are:

Method:

1.

Run-in (warm-up) time of the machining facility

before sampling
Differing pre-machining or production flow
2.

Milieu (Environment):

Room temperature (temperature changes during

production of the sample).
Relative humidity, atmospheric pressure
Vibration acting upon the machining facility

Cumulative Sum (CUSUM) charts: In these charts, the

ordinate of each plotted point represents the algebraic sum
of the previous ordinate and the most recent deviation
from the target.
Exponentially Weighted Moving Average (EWMA)
charts: In these charts, each point on chart represent the
weighted average of current and all previous subgroup
values, giving more weight to recent process history and
decreasing weight for older data.

__________________________________________________________________________________________
Volume: 02 Issue: 08 | Aug-2013, Available @ http://www.ijret.org

71

IJRET: International Journal of Research in Engineering and Technology

In order to correctly explain the results, one have to know

which mathematical model to use, where its limits are and to
what extent it can be used for practical reasons, even if it
differs from the actual situation.
Control charts can be employed for both discrete (countable)
and continuous (measurable) characteristics. Continuous
variables are those which can be calculated over a continuous
range, such as averages, dimensions (length, width, and
height), weight and temperature. Discrete characteristics are
those which can be counted, such as number of product
manufactured of number of parts.

5. 5Ms of SPC:
The 5Ms of SPC i.e. man, machine, material, method and
milieu are the primary groups of input. Each M can be
subdivided, e.g. milieu (environment) in temperature,
vibration, humidity, contamination, lighting, etc.
1. The Man does not set the machine consistently or
thereafter works without concentration; causes
fluctuations, in readings.
2. The Machine is subjected to temperature fluctuations,
clearance in guides and bearings and also to joints and
vibrations-all of this can lead to deviation in dimension
more or less.
3. The Material can have non-homogeneous composition,
inconsistent hardness, internal stresses etc.
4. The Method for the components that are being
manufactured can be wrong. In this case, it would be
judicious, that components are manufactured with another
method.
5. The Milieu (Environment) may differ from time to time
and place to place.
In spite of careful process control, some uncontrolled random
effects of several input cause the deviation of actual
characteristics value from their target values.
The random effects of several inputs ideally result in a normal
distribution for the characteristics. A normal distribution can
be characterized by two parameters i.e. the mean () and the
standard deviation (Sn). The graphic representation of the
density function of a normal distribution show a typical bell
shaped curve, whose inflection point lie at - and + .
Within SPC, the parameters and of the distribution of the
characteristic are determined from the random sample values
and the results obtained are used to assess the current status of
the process.

6. ADVANTAGE OF SPC IMPLEMENTATION:

It could improve process performance by reducing

product variability

eISSN: 2319-1163 | pISSN: 2321-7308

Improves production efficiency by decreasing scrap

and rework
Leads to higher quality product by reducing:
variability and defects
Improving their overall business competitiveness
Minimize rework
Minimize lost of sales
Maintain a desired degree of conformance to design
Eliminate any unnecessary quality checks
Reduce the percentage of defective parts purchased
from vendors
Reduce returns from customers

7. DISADVANTAGE OF SPC IMPLEMENTATION

SPC can take time to apply rigorously but applications do
show that there are few, if any, disadvantages to SPC. Its
application must remain relevant and useful, rather than
becoming a system 'for its own sake'. Problems can occur in
introducing it to avowed innumerate.

8. APPLICATIONS OF SPC:
The application of SPC involves three main sets of activities:
1. The first is understanding the process. This is achieved by
business process mapping.
2. The second is measuring the sources of variation assisted by
the use of control charts.
3. The third is eliminating assignable (special) sources of
variation.
It can be used in various industries for improving the quality
of the product and helps in lowering the product costs as it
provides a better product and/or service.

REFERENCES:
[1]. Manus Rungtusanatham:Beyond improved quality: the
motivational effects of statistical process control, Journal
of Operations Management 19 (2001) 653673.
[2]. Antony J., Balbontin A. and Taner T., (2000). Key
ingredients for the effective implementation of statistical
process control. Work Study, 49(6): 242-247.
[3]. Attaran M., (2000). Why does reengineering fail. A
practical guide for successful implementation. Journal of
Management Development, 19(9): 794-801.
[4]. Benneyan, J.C., Chute, A.D., (1993): SPC, process
improvement, and the Deming PDCA circle in freight
administration. Production and Inventory Management
Journal 34 (1), 3540.
[5]. D. Ridleya, D. Duke (2007), Moving -window spectral
model based statistical process control.
[6]. Deros B. M., Rahman M. N. Ab, Ismail A. R., Yee L.
W. Zain R.M. (2010), Application of Statistical Process
Control Technique for Evaluating Machine Capability: A
Case Study.

__________________________________________________________________________________________
Volume: 02 Issue: 08 | Aug-2013, Available @ http://www.ijret.org

72