FULL RANGE SPEAKER UNIT
FE206En
Features
ES cone and center cap are adapted.
This new diaphragm material has the
fine, supple and high density fiber, and
its characteristics successfully improve
the mid-high frequency reproduction.
146mm strong ferrite magnet is employed.
Well tuned Qts / Mms values for ease of
use in the back loaded horn enclosure.
Specifications
&
Thiele/Small Parameters
35 mm / 1.4 in
Stamped
Cast / Stamped
:
Impedance
:
8
Reproduction Frequency Response
:fs 20 kHz
Sound Pressure Level
:
96 dB/W(m)
30 W
Rated Input
:
90 W
Music Power
:
Ferrite
Magnet Material :
Magnet Weight
(main)
(cancel)
Net Weight
: 1,067
: n/a
3,200
a:
D:
Sd :
Zn :
Fs :
Re :
Le :
Qms :
Qes :
Qts :
Mms :
BL :
Vas :
Xmax :
Eff/0 :
Cms :
EBP :
Frequency Response / Impedance
g / 2.352 lb
g / n/a
lb
g / 7.055 lb
81 mm
162 mm
0.0206 m
8
45 Hz
6.8
0.0525 mH
4.57
0.194
0.19
12.2 g
2
10.65 Telsa/m
70.99 L
0.8 mm
2.68 %
1.172 m/N
231.96
Dimensions & Mounting Information
220
4-5
208
182
3.5
Voice Coil Diameter
:
200 mm / 7.9 in
48
87.9
Size
145
Overall Diameter :
Baffle Hole Diameter
:
Depth
:
208 mm / 8.2 in
185 mm / 7.3 in
87.9 mm / 3.5 in
Recommended Back Loaded Horn Type Enclosure
This example shows a back
loaded horn type enclosure for
FE206En.
FE206Ens magnetic circuit with
146mm large ferrite magnet
provides sharper resonance and
makes the unit suitable for a back
loaded horn type enclosure.
110
100
90
80
70
60
50
(dB)
20 Hz
50
100
200
500 1000
2k
5k
10k
20k
21mm thick plywood is used for
main section and side panels to
ensure a strong enclosure.
Two way system using super
tweeter T90A is also recommended.
FE206E
Capacitor 0.68 - 0.33 F
408
21
313
250
12
14
219
50
300
13
7
47
145
27
40
28
42
100
42
15
290
50
150
50
100
21
100
100
23
100
100
25
24
26
30
31 33
450
17
100
20
21
22
100
125
100
50
100
36
16
255
120
900
11
29
4
392
(111)
87
275
220
( 22 )
522
440
52
200
74
160
350
100
10
9
35
T90A
100
19
32
50
18
313
219
24 20
14 14
25
392
77
250
23
23
4-100
21
21
858
80
408
11
2 11
4-50
30
12
350
50
6
6
40
219
160
19
33
80
290
31
80
290
32
55
780
255
22
10
10
200
29 29
80
99
150
392
350
74
27
27
80
26
350
450
220
100
275
36
35
1313
44
33
18
290
150
17
150
780
88
145
16
440
150
28
28
15
150
145
50 100
350
350
This example has sufficient internal volume. However, if you prefer tighter
sound reproduction, you can reduce airspace using sands or other fill material.
6
6
40
11
2 11
219
24 20
4-50
Sound
Absorbents
300
313
219
160
522
*Italic font means part number.
900
450
450
25
14 14
Placing thin sound absorbent material as shown enable reduction of peaks & dips
around 150 to 400Hz band width. However, it may reduce transient response. You
should adjust it to your taste.
77
250
23
23
4-100
Sands
21
21
Sands
55
10
10
29 29
200
180
FE206En is designed for use in a back loaded horn type enclosure and it is generally
unsuitable for bass reflex because of its over
damping sound characteristics. However, it
is possible to use the FE206En in a bass reflex enclosure as shown.
This example is a narrow and tall style bass
reflex type enclosure. Internal volume of 45
liters tuned to approximately 50Hz (Fb).
Low frequency response from around 120Hz
50 100
is gently350damped with a 350controlled
peak at
50 - 60Hz.
180
780
255
22
150
Sound 220
Absorbents
99
74
27
27
80
100
In order to avoid unwanted mid/high frequency dispersion of the horn, we recommend damping the enclosure with filler and sound absorption material.
275
Bass Reflex Type Enclosure
1313
44
unit : mm
33
18
290
150
750
600
786
150
180
180
17
780
16
150
400
440
28
28
80
unit : mm
75
15
200
88
145
300
150
240
276
85
750
600
786
145
*Italic font means part number.
522
85
264
300
Distributor / Authorised Dealer
www.fostex.jp
Fostex Co. ,3-2- 35 Musa shino, Akishima,T okyo,J apa n 196-0 021
Tel :+81(0) 42-546-497 4 Fax:+8 1(0)42 -546 -92 22
In accordance with our policy of continuous development, we reserve the right to change specifica
tions without notice.
Printed in China 500134