Analysis of Stresses:: X y Xy

01-10-2010
Lecture 3
LECTURE 3
Analysis of Stresses:
Consider a point q' in some sort of structural member like as shown in figure below. Assuming that at
point exist. q' a plane state of stress exist. i.e. the state of state stress is to describe by a parameters x,
y and xy These stresses could be indicate a on the two dimensional diagram as shown below:
This is a commen way of representing the stresses. It must be realize a that the material is unaware of what
we have called the x and y axes. i.e. the material has to resist the loads irrespective less of how we wish to
name them or whether they are horizontal, vertical or otherwise further more, the material will fail when the
stresses exceed beyond a permissible value. Thus, a fundamental problem in engineering design is to
determine the maximum normal stress or maximum shear stress at any particular point in a body. There is
no reason to believe apriori that x, y and xy are the maximum value. Rather the maximum stresses may
associates themselves with some other planes located at '. Thus, it becomes imperative to determine the
values of and . In order tto achieve this let us consider the following.
nptel.iitm.ac.in/courses//lecture3.htm
1/7
01-10-2010
Lecture 3
Shear stress:
If the applied load P consists of two equal and opposite parallel forces not in the same line, than there is a
tendency for one part of the body to slide over or shear from the other part across any section LM. If the
cross section at LM measured parallel to the load is A, then the average value of shear stress = P/A . The
shear stress is tangential to the area over which it acts.
If the shear stress varies then at a point then may be defined as
Complementary shear stress:
Let ABCD be a small rectangular element of sides x, y and z perpendicular to the plane of paper let there
be shear stress acting on planes AB and CD
It is obvious that these stresses will from a couple ( . xz )y which can only be balanced by tangential forces
on planes AD and BC. These are known as complementary shear stresses. i.e. the existence of shear
stresses on sides AB and CD of the element implies that there must also be complementary shear stresses
on to maintain equilibrium.
Let ' be the complementary shear stress induced on planes
AD and BC. Then for the equilibrium ( . xz )y = ' ( yz )x
= '
Thus, every shear stress is accompanied by an equal complementary shear stress.
Stresses on oblique plane: Till now we have dealt with either pure normal direct stress or pure shear
stress. In many instances, however both direct and shear stresses acts and the resultant stress across any
section will be neither normal nor tangential to the plane.
A plane stse of stress is a 2 dimensional stae of stress in a sense that the stress components in one
direction are all zero i.e
z = yz = zx = 0
2/7
01-10-2010
Lecture 3
examples of plane state of stress includes plates and shells.

Consider the general case of a bar under direct load F giving rise to a stress y vertically
The stress acting at a point is represented by the stresses acting on the faces of the element enclosing the
point.
The stresses change with the inclination of the planes passing through that point i.e. the stress on the
faces of the element vary as the angular position of the element changes.
Let the block be of unit depth now considering the equilibrium of forces on the triangle portion ABC
Resolving forces perpendicular to BC, gives
.BC.1 = ysin . AB . 1
but AB/BC = sin or AB = BCsin
Substituting this value in the above equation, we get
.BC.1 = ysin . BCsin . 1 or
(1)
Now resolving the forces parallel to BC

.BC.1 = y cos . ABsin . 1
again AB = BCcos
.BC.1 = ycos . BCsin . 1 or = ysincos
(2)
If = 900 the BC will be parallel to AB and = 0, i.e. there will be only direct stress or normal stress.
By examining the equations (1) and (2), the following conclusions may be drawn
(i) The value of direct stress is maximum and is equal to y when = 900 .
3/7
01-10-2010
Lecture 3
(ii) The shear stress has a maximum value of 0.5 y when = 450
(iii) The stresses and are not simply the resolution of y
Material subjected to pure shear:
Consider the element shown to which shear stresses have been applied to the sides AB and DC
Complementary shear stresses of equal value but of opposite effect are then set up on the sides AD and
BC in order to prevent the rotation of the element. Since the applied and complementary shear stresses are
of equal value on the x and y planes. Therefore, they are both represented by the symbol xy.
Now consider the equilibrium of portion of PBC
Assuming unit depth and resolving normal to PC or in the direction of

.PC.1 = xy.PB.cos.1+ xy.BC.sin.1
= xy.PB.cos + xy.BC.sin
Now writing PB and BC in terms of PC so that it cancels out from the two sides
PB/PC = sin BC/PC = cos
.PC.1 =
xy.cossinPC+
xy.cos.sinPC
= 2xysincos
4/7
01-10-2010
Lecture 3
= xy.2.sincos
(1)
Now resolving forces parallel to PC or in the direction .then xyPC . 1 = xy . PBsin xy . BCcos
ve sign has been put because this component is in the same direction as that of .
again converting the various quantities in terms of PC we have
xyPC . 1 = xy . PB.sin2 xy . PCcos2
= [ xy (cos2 sin2 ) ]
= xycos2 or
(2)
the negative sign means that the sense of is opposite to that of assumed one. Let us examine the
equations (1) and (2) respectively
From equation (1) i.e,
= xy sin2
The equation (1) represents that the maximum value of is xy when = 450.
Let us take into consideration the equation (2) which states that
= xy cos2
It indicates that the maximum value of is xy when = 00 or 900. it has a value zero when = 450 .
From equation (1) it may be noticed that the normal component has maximum and minimum values of
+xy (tension) and xy (compression) on plane at 450 to the applied shear and on these planes the
tangential component is zero.
Hence the system of pure shear stresses produces and equivalent direct stress system, one set
compressive and one tensile each located at 450 to the original shear directions as depicted in the figure
below:
5/7
01-10-2010
Lecture 3
Material subjected to two mutually perpendicular direct stresses:

Now consider a rectangular element of unit depth, subjected to a system of two direct stresses both tensile,
x and yacting right angles to each other.
for equilibrium of the portion ABC, resolving perpendicular to AC

. AC.1 = y sin . AB.1 + x cos . BC.1
converting AB and BC in terms of AC so that AC cancels out from the sides
= y sin2 + xcos2
Futher, recalling that cos2 sin2 = cos2 or (1 cos2)/2 = sin2
Similarly (1 + cos2)/2 = cos2q
Hence by these transformations the expression for reduces to
= 1/2 y (1 cos2) + 1/2 x (1 + cos2)
6/7
01-10-2010
Lecture 3
On rearranging the various terms we get
(3)
Now resolving parallal to AC

sq.AC.1= xy..cos.AB.1+ xy.BC.sin.1
The ve sign appears because this component is in the same direction as that of AC.
Again converting the various quantities in terms of AC so that the AC cancels out from the two sides.
(4)
Conclusions :
The following conclusions may be drawn from equation (3) and (4)
(i) The maximum direct stress would be equal to x or y which ever is the greater, when = 00 or 900
(ii) The maximum shear stress in the plane of the applied stresses occurs when = 450
Goto Home
7/7

Analysis of Stresses:: X y Xy

Uploaded by

Copyright:

Available Formats

Analysis of Stresses:: X y Xy

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Analysis of Stresses:: X y Xy

Uploaded by

Copyright:

Available Formats

01-10-2010

examples of plane state of stress includes plates and shells.

Now resolving the forces parallel to BC

Assuming unit depth and resolving normal to PC or in the direction of

Material subjected to two mutually perpendicular direct stresses:

for equilibrium of the portion ABC, resolving perpendicular to AC

On rearranging the various terms we get

Now resolving parallal to AC

You might also like