Home Cinema

DVD HOME THEATRE SYSTEM
User Manual
HTS3154
Manuel Dutilisation
54
Manual del usuario
102
Benutzerhandbuch
150
Gebruikershandleiding
198
welcome
1_hts3154_eu_eng3.indd 1
2007-04-26 10:53:21 AM
Important notes for users in the

U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of
plug proceed as follows:
Italia
DICHIARAZIONE DI CONFORMITA
Si dichiara che lapparecchio HTS3154, Philips
risponde alle prescrizioni dellart. 2 comma 1
del D.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
1 Remove fuse cover and fuse.
Philips Consumer Electronics

Philips, Glaslaan 2
5616 JB Eindhoven, The Netherlands
2 Fix new fuse which should be a BS1362

5 Amp, A.S.T.A. or BSI approved type.
3 Refit the fuse cover.

If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse
is used, the fuse at the distribution board
should not be greater than 5 Amp.
Note: The severed plug must be disposed of to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
How to connect a plug

The wires in the mains lead are coloured with
the following code: blue = neutral (N),
brown = live (L).
As these colours may not correspond with the
colour markings identifying the terminals in
your plug, proceed as follows:
Connect the blue wire to the terminal
marked N or coloured black.
Connect the brown wire to the terminal
marked L or coloured red.
Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
Copyright in the U.K.

Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performers Protection Acts 1958 to
1972.
Norge
Typeskilt finnes p apparatens underside.
Observer: Nettbryteren er
sekundert innkoplet. Den innebygde
netdelen er derfor ikke frakoplet
nettet s lenge apparatet er
tilsluttet nettkontakten.
For redusere faren for brann eller elektrisk
stt, skal apparatet ikke utsettes for regn eller
fuktighet.
ATTENTION!
For Customer Use:
Read carefully the information located at the
bottom or rear of your DVD Home Theatre
System and enter below the Serial No. Retain
this information for future reference.
Model No.
HTS3154
Serial No.
_______________
DK
Advarsel: Usynlig laserstrling ved
bning nr sikkerhedsafbrydere er ude
af funktion. Undg utsttelse for
strling.
Bemrk: Netafbryderen er sekundrt
indkoblet og ofbryder ikke strmmen
fra nettet. Den indbyggede netdel er
derfor tilsluttet til lysnettet s lnge
netstikket sidder i stikkontakten.
S
Klass 1 laseraparat
Varning! Om apparaten anvnds p
annat stt n i denna bruksanvisning
specificerats, kan anvndaren utsttas
fr osynlig laserstrlning, som
verskrider grnsen fr laserklass 1.
Observera! Stmbrytaren r sekundrt
kopplad och bryter inte strmmen frn
ntet. Den inbyggda ntdelen r drfr
ansluten till elntet s lnge
stickproppen sitter i vgguttaget.
SF
Luokan 1 laserlaite
Varoitus! Laitteen kyttminen muulla
kuin tss kyttohjeessa mainitulla
tavalla saattaa altistaa kyttjn
turvallisuusluokan 1 ylittvlle
nkymttmlle lasersteilylle.
Oikeus muutoksiin varataan. Laite ei
saa olla alttiina tippu-ja roiskevedelle.
Huom. Toiminnanvalitsin on kytketty
toisiopuolelle, eik se kytke laitetta irti
shkverkosta. Sisnrakennettu
verkko-osa on kytkettyn
shkverkkoon aina silloin, kun pistoke
on pistorasiassa.
LASER
Type
Wave length
Output Power
Beam divergence
CAUTION
VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. AVOID
EXPOSURE TO BEAM
ADVARSEL
SYNLIG OG USYNLIG LASERSTRLING
VED BNING UNDG UDSTTELSE
FOR STRLING
VARNING
SYNLIG OCH OSYNLIG
LASERSTRLNING NR DENNA DEL
R PPNAD BETRAKTA EJ STRLEN
VARO!
AVATTAESSA OLET ALTTIINA
NKYVLLE JA NKYMTTMLLE
LASER STEILYLLE. L KATSO
STEESEEN
VORSICHT
SICHTBARE UND UNSICHTBARE
LASERSTRAHLUNG WENN
ABDECKUNG GEFFNET NICHT DEM
STRAHL AUSSETZEN
ATTENTION
RAYONNEMENT LASER VISIBLE ET
INVISIBLE EN CAS DOUVERTURE
EXPOSITION DANGEREUSE AU
FAISCEAU
This product complies with the radio

interference requirements of the
European Community.
This product complies with
the requirements of the
following directives and
guidelines: 73/23/EEC +
89/336/EEC + 93/68/EEC
Semiconductor laser
GaAIAs
650 - 660 nm (DVD)
784 - 796 nm (CD)
7 mW (DVD)
10 mW (VCD/CD)
60 degrees
Disposal of your old product

Your product is designed and manufactured with high quality materials
and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate collection system for
electrical and electronic products.
Please act according to your local rules and do not dispose of your old products with
your normal household waste. The correct disposal of your old product will help
prevent potential negative consequences for the environment and human health.
Se dbarrasser de votre produit usag (Franais)

Votre produit est conu et fabriqu avec des matriaux et des
composants de haute qualit, qui peuvent tre recycls et utiliss de
nouveau.
Lorsque ce symbole d'une poubelle roue barre est attach un
produit, cela signifie que le produit est couvert par la Directive
Europenne 2002/96/EC.
Veuillez vous informer du systme local de sparation des dchets
lectriques et lectroniques.
Veuillez agir selon les rgles locales et ne pas jeter vos produits usags avec les dchets
domestiques usuels. Jeter correctement votre produit usag aidera prvenir les
consquences ngatives potentielles contre l'environnement et la sant humaine.
Cmo deshacerse del producto usado (Espaol)

Su producto ha sido diseado y fabricado con materiales y componentes de
alta calidad, que pueden ser reciclados y reutilizados.
Cuando vea este smbolo de una papelera con ruedas tachada junto a un
producto, esto significa que el producto est bajo la Directiva Europea
2002/96/EC
Deber informarse sobre el sistema de reciclaje local separado para
productos elctricos y electrnicos.
Siga las normas locales y no se deshaga de los productos usados tirndolos en la basura
normal de su hogar. El reciclaje correcto de su producto usado ayudar a evitar
consecuencias negativas para el medio ambiente y la saludde las persona.
Entsorgung Ihres Altgertes (Deutsch)

Ihr Produkt ist aus hochqualitativen Materialien und Bestandteilen hergestellt,
die dem Recycling zugefhrt und wiederverwertet werden knnen.
Falls dieses Symbol eines durchgestrichenen Mllcontainers auf Rollen auf
diesem Produkt angebracht ist, bedeutet dies, dass es von der Europischen
Richtlinie 2002/96/EG erfasst wird.
Bitte informieren Sie sich ber die rtlichen Sammelstellen fr Elektroprodukte
und elektronische Gerte.
Bitte beachten Sie die lokalen Vorschriften und entsorgen Sie Ihre Altgerte nicht mit dem
normalen Haushaltsmll. Die korrekte Entsorgung Ihres Altgertes ist ein Beitrag zur
Vermeidung mglicher negativer Folgen fr die Umwelt und die menschliche Gesundhei.
Wegwerpen van uw afgedankt apparaat (Nederlands)

Uw apparaat werd ontworpen met en vervaardigd uit onderdelen en
materialen van superieure kwaliteit, die gerecycleerd en opnieuw gebruikt
kunnen worden.
Wanneer het symbool van een doorstreepte vuilnisemmer op wielen op
een product is bevestigd, betekent dit dat het product conform is de
Europese Richtlijn 2002/96/EC
Gelieve u te informeren in verband met het plaatselijke inzamelingsysteem
voor elektrische en elektronische apparaten.
Gelieve u te houden aan de plaatselijke reglementering en apparaten niet met het gewone
huisvuil mee te geven. Door afgedankte apparaten op een correcte manier weg te werpen
helpt u mogelijke negatieve gevolgen voor het milieu en de gezondheid te voorkomen.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH

DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE STANDARD
DEFINITION OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.
Franais ---------------------------------- 54
Windows Media and the Windows logo are

trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
Deutsch -------------------------------- 150
Deutsch
DivX Ultra Certified products: DivX, DivX

Ultra Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
Espaol -------------------------------- 102
Nederlands ---------------------------- 198
Nederlands
Manufactured under license from one or

more of the following DTS, Inc. U.S. Pat.
Nos: 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535 and other U.
S. and world-wide patents issued and
pending. DTS and DTS Digital Surround
are registered trademarks of DTS, Inc.
Copyright 1996, 2002-2006, DTS, Inc. All
Rights Reserved.
Franais
English ------------------------------------ 6
Espaol
Manufactured under license from Dolby

Laboratories, Dolby, Pro Logic and the
double-D symbol are trademarks of Dolby
Laboratories.
English
Index
This product incorporates copyright protection

technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and
other rights owners. Use of this copyright
protection technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reserve engineering or disassembly is prohibited.
Table of contents
English
General
General Information ........................................................................................................ 8
Setup precautions.................................................................................................................................................8
Accessories supplied ...........................................................................................................................................8
Cleaning discs ........................................................................................................................................................8
About recycling .....................................................................................................................................................8
Product Overview
Main Unit ........................................................................................................................... 9
Remote Control .........................................................................................................10-12
Using the remote control ................................................................................................................................12
Connections
Basic Connections .....................................................................................................13-17
Step 1: Placing the speakers.............................................................................................................................13
Step 2: Connecting to TV ..........................................................................................................................14-15
Option 1: Using the Scart socket ...........................................................................................................14
Option 2: Connecting to a Progressive Scan TV or component video input ............................15
Step 3: Connecting speakers and subwoofer .............................................................................................16
Step 4: Connecting the FM and AM/MW antennas ..................................................................................17
Step 5: Connecting the power cord ..............................................................................................................17
Optional Connections .................................................................................................... 18

Connecting to cable box/satellite receiver and recorder/VCR ............................................................18
Basic Setup
Getting Started ..........................................................................................................19-23
Finding the correct viewing channel .............................................................................................................19
Switching to different play source .................................................................................................................19
Setting language preferences.......................................................................................................................... 20
On-screen display (OSD) language ....................................................................................................... 20
Audio, Subtitle and Menu language for DVD playback .............................................................. 20-21
Setting the TV Display ......................................................................................................................................21
Setting up Progressive Scan feature ............................................................................................................. 22
Setting the speakers channels ........................................................................................................................23
Disc Playback
Disc Operations ........................................................................................................ 24-32
Playable discs .......................................................................................................................................................24
Playing a disc ........................................................................................................................................................24
Basic playback controls.................................................................................................................................... 25
Selecting various repeat/shuffle functions.................................................................................................. 25
Programming disc tracks ..................................................................................................................................26
Other playback features for video discs (DVD/VCD/SVCD) ......................................................... 26-29
Using the Disc Menu ..................................................................................................................................26
Viewing playback information ..................................................................................................................27
Zooming in/out ............................................................................................................................................27
Changing subtitle language .......................................................................................................................27
Switching camera angles ............................................................................................................................27
Changing sound track language .............................................................................................................. 28
Setting the delay times for audio playback.......................................................................................... 28
Playback Control (VCD only)................................................................................................................. 28
Preview function (VCD/SVCD only) .....................................................................................................29
Playing a MP3/ WMA disc ............................................................................................................................... 30

Playing a JPEG image file (slide show) ...........................................................................................................31
Preview function ..........................................................................................................................................31
Zoom picture ...............................................................................................................................................31
Rotating/flipping the picture ....................................................................................................................31
Playing MP3/WMA music and JPEG pictures simultaneously ................................................................32
Playing a DivX disc .............................................................................................................................................32
Playback other supported devices

Playback - USB Device ................................................................................................... 33
Playing from USB flash drive or USB memory card reader....................................................................33
Playback - Other Audio Player ..................................................................................... 34

Playing from other portable audio player ................................................................................................... 34
Setup Options
Setup Menu Options................................................................................................. 35-41
Accessing the setup menu................................................................................................................................35
General Setup Page............................................................................................................................................36
Audio Setup Page................................................................................................................................................37
Video Setup Page ......................................................................................................................................... 38-39
Preference Page ...........................................................................................................................................40-41
Radio Tuning
Radio Operations ...................................................................................................... 42-43
Tuning to radio stations....................................................................................................................................42
Presetting radio stations ..................................................................................................................................42
Using auto install .................................................................................................................................. 42-43
Using automatic preset..............................................................................................................................43
Using manual preset ...................................................................................................................................43
Selecting a preset radio station ......................................................................................................................43
Deleting a preset radio station.......................................................................................................................43
Others
Sound and Volume Controls ......................................................................................... 44
Volume control .................................................................................................................................................. 44
Selecting surround sound................................................................................................................................ 44
Selecting digital sound effects ........................................................................................................................ 44
Other Features................................................................................................................45
Installing the latest software .......................................................................................................................... 45
Setting the Sleep timer .................................................................................................................................... 45
Troubleshooting ........................................................................................................ 46-48

Frequently Asked Questions (USB) ............................................................................. 49
Glossary...................................................................................................................... 50-51
Specifications .................................................................................................................. 52
English
Table of contents
General Information
English
WARNING!
This unit does not contain any userserviceable parts. Please leave all
maintenance work to qualified
personnel.
Setup precautions
Finding a suitable location
Place this unit on a flat, hard and
stable surface. Never place the unit on a
carpet.
Never place this unit on top of other
equipment that might heat it up (e.g.,
receiver or amplifier).
Never put anything under this unit
(e.g., CDs, magazines).
Install this unit near the AC outlet
where the AC power plug can be easily
reached.
Space for ventilation
Place this unit in a location with
adequate ventilation to prevent internal
heat build up. Allow at least 10 cm (4)
clearance from the rear and the top of
this unit and 5cm (2) from the left and
right to prevent overheating.
Avoid high temperature, moisture,
water and dust
This unit must not be exposed to
dripping or splashing.
Never place any object or items that
can damage this unit (e.g., liquid filled
objects, lighted candles).
Accessories supplied
1 subwoofer
2 front speakers
2 rear speakers
1 centre speaker
1 remote control with batteries
1 scart cable
1 FM wire antenna
1 AM/MW loop antenna
1 MP3 LINE-IN cable (for connecting
portable audio player)
Quick Start Guide
Cleaning discs
To clean a disc, use a micro fibre cleaning
cloth and wipe the disc from the centre
to the edge in a straight line.
CAUTION!
Never use solvents e.g. benzene, thinner,
commercially available cleaners, or antistatic sprays intended for discs.
About recycling
These operating instructions have been
printed on non-polluting paper. The
electronic equipment contains a large
number of materials that can be recycled.
If you are disposing of an old machine,
please take it to a recycling centre.
Please observe the local regulations
regarding disposal of packaging materials,
exhausted batteries and old equipment.
Main Unit
10
English
Right
side view
Front view
11
a STANDBY-ON
h STOP
Turns on this unit or turns off to normal

standby mode.
b Disc Tray
Exits an operation.
DISC: stops playback.
RADIO: press and hold this button to
erase the current preset radio station.
c OPEN/CLOSE
Opens/closes the disc tray.
i VOL
Adjusts the volume level.
d Display panel
j USB socket
Input for USB flash drive or USB memory
card reader.
e PLAY/ PAUSE u
DISC: starts/pauses playback.
RADIO: starts auto radio installation for
first time setup.
f SOURCE
Selects the relevant active source mode:
DISC, FM, AM/MW, TV, AUX, MP3
LINE-IN.
k MP3 LINE-IN socket

Phono input for connecting to the
headphone out socket on your portable
audio player.
g SURROUND
Selects multi-channel surround or stereo
mode.
Remote Control
English
c OPEN/CLOSE
1
Opens/closes the disc tray.
d PROGRAM
DISC: starts programming.
start automatic/ manual preset
programming.
3
SLEEP
4
65
6
e SLEEP
Sets the sleep timer function.
7
8
9
10
11
12
13
f SETUP
Enters or exits the system setup menu.
g DISPLAY
Displays the current status or disc
information.
Selects a different viewing angle of a DVD
movie (if available).
h PLAY/PAUSE u
DISC: starts/pauses playback.
RADIO: starts auto radio installation for
first time setup.
i STOP x
Exits an operation.
DISC: stops playback.
erase the current preset radio station.
a 2
Turns on this unit or turns off to normal
standby mode.
j TV VOL +/-
b Source buttons
k AUDIO SYNC
DISC/USB: toggles between DISC or

USB mode.
RADIO: toggles between FM and AM/
MW band.
TV: switches to TV mode. The sound
from the TV will output through the
connected speaker system.
AUX/DI: switches to the external device
that is connected to the AUDIO IN-AUX
socket.
MP3 LINE-IN: switches to audio device
that is connected to the MP3 LINE-IN
socket.
10
Adjusts the volume of the TV (for Philips

TVs or compatible brands only).
Sets the audio output delay times if the
video playback is slower than the audio
output.
l REPEAT
Selects various repeat or shuffle modes;
turns off repeat or shuffle mode.
m ZOOM
Zoom in or out the picture on the TV.
Remote Control (continued)

English
n DISC MENU
For DVD, enters or exits disc contents
menu.
For VCD/SVCD, enters digest menu.
o OK
Confirms an entry or selection.
p vVb B
DISC: selects movement direction in the
menu.
DISC: press left or right for fast forward
and backward search.
RADIO: press up or down to tune the
radio frequency.
RADIO: press left or right to start auto
search.
q TITLE
For DVD, go back to the previous menu.
For VCD version 2.0 only;
During playback, display the disc title
menu or return to the main menu.
r PREV / NEXT
SLEEP
14
15
16
17
18
19
20
21
22
23
24
25
DISC: skips to the previous or next title/

chapter/track.
RADIO: selects a preset radio station.
s MUTE %
Mutes or restores the volume.
t VOL +/ Adjusts the volume level.
u SURROUND
Selects multi-channel surround or
stereo mode.
x SUBTITLE
Selects a DVD subtitle language.
y AUDIO
DISC: selects an audio language/channel.
v Numeric keypad 0-9

Enters a track/title number of the disc.
Enters a number of a preset radio station.
w SOUND
Selects a predefined sound effect.
11
Remote Control (continued)

English
Using the remote control
A Open the battery compartment.

B Insert two batteries type R03 or AAA,
following the indications (+-) inside
the compartment.
C Close the cover.

D Point the remote control directly at the
remote sensor (iR) on the front panel.
E Select the source you wish to control by

pressing the DISC/USB, RADIO, TV,
AUX/DI or MP3 LINE-IN button on the
remote control.
F Then select the desired function (for

example , ).
12
CAUTION!
Remove batteries if they are
exhausted or if the remote control
is not to be used for a long time.
Never mix batteries (old and new
or carbon and alkaline, etc).
Batteries contain chemical
substances, they should be disposed
of properly.
English
Basic Connections
REAR
LEFT
FRON
T
LEFT
FRON
T
RIGHT
REAR
RIGHT
Step 1: Placing the speakers

The Philips Home Theatre System is
simple to install. However, proper system
placement is critical to ensure an
optimum sound experience.
A Place the front left and right speakers at

equal distances from the TV and at an
angle of approximately 45 degrees from
the listening position.
B Place the centre speaker above the TV or

the main unit such that the centre
channels sound is localised.
SUB
WOO
FER
Helpful Hints:
The placement diagram shown here is only
a guideline that provides great system
performance. You may find other placement
choices that are more suitable for your room
layout that provide the sound experience you
enjoy.
To avoid magnetic interference, never
position the front speakers too close to your
TV.
The rear speakers are labelled as REAR
LEFT or REAR RIGHT.
The front speakers are labelled as
FRONT LEFT or FRONT RIGHT.
For speaker setting, see Getting Started Setting the speakers channel.
C Place the rear speakers at normal

listening ear level facing each other or
hang on the wall.
D Place the subwoofer at the corner of the

room. Otherwise, keep it at least one
metre away from the TV.
13
Basic Connections (continued)

English
Option 1
Main Unit (rear)
SPEAKERS
AUDIO IN
VIDEO OUT
AM/
MW
L
Pr
R
AUX
Step 2: Connecting to TV
This connection enables you to view the
video playback from this unit. You only
need to choose one of the options
below to make the video connection.
For a standard TV, follow option 1.
For a progressive scan TV, follow
option 2.
Helpful Hint:
It is important to connect this unit directly
to the TV in order to enjoy optimum video
quality.
14
Pb
SCART
Option 1: Using the Scart socket

Connect the scart cable (supplied) from
the SCART socket on the main unit to
the corresponding SCART input socket
on the TV.
Helpful Hint:
With this connection, you can press TV on
the remote control to route the TVs audio to
this units speakers.
English
VIDEO OUT
Pr
Option 2
Pb
Main Unit (rear)

SPEAKERS
AUDIO IN
VIDEO OUT
AM/
MW
L
Pr
R
AUX
Option 2: Connecting to a
Progressive Scan TV or component
video input
The progressive scan video quality is
only available when using Y Pb Pr
connection and a progressive scan TV is
required. It provides superior picture
quality when watching DVD movies.
Pb
SCART
Helpful Hint:
To route the TVs audio to the speakers on
this unit, connect an audio cable from the
AUDIO IN-AUX sockets to the corresponding
AUDIO output sockets on the TV. Press
AUX/DI on the remote control when
watching the TV programmes.
A Connect the component video cables

(red/ blue/green - not supplied) from the
Y Pb Pr sockets on the main unit to the
corresponding component video input
sockets (or labelled as Y Pb/Cb Pr/Cr or
YUV) on the TV.
B If your TV accepts progressive signals,

proceed to chapter Getting Started Setting up Progressive Scan feature for
detailed progressive feature setup.
15

English
FRONT CENTRE
FRONT
RIGHT
FRONT
LEFT
SUBWOOFER
REAR LEFT
SPEAKERS
AUDIO IN
REAR RIGHT
VIDEO OUT
AM/
MW
L
Pr
R
AUX
Step 3: Connecting speakers

and subwoofer
Connect all the speakers and subwoofer
to the matching sockets at the rear of the
main unit, Make sure that the colours of
the plugs and sockets are matched.
Helpful Hints:
To prevent unwanted noise, never place
the speakers too close to the main unit,
subwoofer, AC power adapter, TV or any
other radiation sources.
16
Pb
SCART
fix the claw

into the slot
Main Unit (rear)

SPEAKERS
AUDIO IN
VIDEO OUT
AM/
MW
L
Pr
R
AUX
Pb
SCART
FM
antenna
1
AM/MW
antenna
AUDIO IN
VIDEO OUT
AM/
MW
L
Pr
R
AUX
Pb
SCART
Step 4: Connecting the

FM and AM/MW
antennas
A Connect the supplied AM/MW loop
antenna to the AM/MW socket. Place
the AM/MW loop antenna on a shelf, or
attach it to a stand or wall.
B Connect the supplied FM antenna to the

FM 75 socket. Extend the FM antenna
and fix its ends to the wall.
For better FM stereo reception, connect
an external FM antenna (not supplied).
Helpful Hints:
Adjust the position of the antennas for
optimal reception.
Position the antennas as far away as
possible from your TV, VCR or other
radiation source to prevent any unwanted
interference.
Step 5: Connecting the

power cord
After everything is connected
properly, connect the AC power
cord into the power outlet.
The standby LED on the main unit lights
up.
Note:
Turning off to standby mode does not
disconnect the unit from mains.
Helpful Hints:
Refer to the type plate at the rear or
bottom of the product for identification and
supply ratings.
Before making or changing any
connections, make sure that all the devices
are disconnected from the power outlet.
17
English
Optional Connections
English
Main Unit (rear)

SPEAKERS
AUDIO IN
VIDEO OUT
AM/
MW
AUDIO IN
Pr
L
AUX
Pb
AUX
EXT 2
EXT 1
TV (rear)
DVD Recorder/VCR (rear)

EXT 2
TV-OUT
SCART IN/OUT
AUX - I/O
EXT 1
TO TV - I/O
ANTENNA-IN
MAINS
A
IN
RF
VIDEO
OUT
AUDIO
L
S-VIDEO
Connecting to cable box/

satellite receiver and
recorder/VCR
You can connect the audio output from
an analogue audio/video device (e.g. VCR,
Cable/Satellite Box or TV) to this Home
Theatre Audio System in order to enjoy
the multi-channel surround sound
capabilities
Note:
The above illustration is only an example
of the possible connections. It may be
varied depending on the connected
devices.
18
TO TV
Cable/Satellite Box
(rear)
A Keep the existing connections between

your TV and other devices.
B Use the scart cable to connect this unit

to your TV.
If your TV does not have double-scart
connectors, see Step 2: Connecting to
TV for other video connection options.
C Use an audio cable (red/white - not

supplied) to connect the AUDIO INAUX sockets on the main unit to the
AUDIO OUT sockets on the Cable/
Satellite Box.
Helpful Hint:
Refer to the connected devices user
manual for other possible connections.
Finding the correct viewing

channel
A Press SOURCE button on the main unit
until DISC appears on the display panel
(or DISC/USB on the remote control).
B Turn on the TV and switch it to the

correct video-in channel.
You may go to the lowest channel on
your TV, then press the Channel Down
button on your TVs remote control until
you see the Video In channel.
You may press button repeatedly
on your TVs remote control.
Usually this channel is between the
lowest and highest channels and may be
called FRONT, A/V IN, VIDEO, etc..
Refer to your TVs user manual on
how to select the correct input on your
TV.
English
Getting Started
Switching to different play
source
Press the SOURCE button on the front
panel repeatedly to select:
DISC FM AM/MW TV
AUX MP3 LINE-IN DISC ....
Or
Press DISC/USB, RADIO, TV,
AUX/DI or MP3 LINE-IN on the
remote control.
Press DISC/USB to toggle between
DISC and USB mode (if USB is detected).
Press RADIO to toggle between FM
and AM/MW band.
If the scart cable is connected from
this unit to your TV, press TV to hear
the TVs sound output through this unit.
Press AUX/DI for switching to the
external device that is connected to the
AUDIO IN-AUX socket on this unit.
Press MP3 LINE-IN for switching to
the portable audio player that is
connected to the MP3 LINE-IN socket on
this unit.
SLEEP
19
Getting Started (continued)

English
Setting language preferences
Audio, Subtitle and Menu language

for DVD playback
The language options are different

depending on your country or region. It
may not correspond to the illustrations
shown on the user manual.
You can select your preferred language

settings for DVD playback. If the selected
language is recorded on the DVD disc,
this unit automatically plays the disc in
that language. Otherwise, the discs
default language will be used instead.
On-screen display (OSD) language

The OSD (On-Screen Display) language
for this unit remains as you have set it,
regardless of the changes made to the
DVD disc language.
A In disc mode, press SETUP on the
A Press twice to stop playback (if any),

then press SETUP.
B Press
repeatedly to select
{ Preference Page }.
C Use
keys to select one of the

options below and press .
remote control.
{ General Setup Page } appears.
Preference Page
B Press
to highlight { OSD Language }

in the menu and press .
Audio
Subtitle
Disc Menu
Parental
Surround
PBC
MP3/JPEG Nav
Password
General Setup Page

Disc Lock
Display Dim
Program
OSD Language
Screen Saver
Sleep
DivX(R) VOD Code
C Use
English
Dansk
Nederlands
Suomi
Franais
Deutsch
Italiano
Norsk
keys to select a language and

press OK to confirm.
English
Chinese (Simp)
French
Spanish
Portuguese
Polish
Italian
Turkish
{ Audio }
Select the preferred audio language for
DVD playback.
{ Subtitle }
Select the preferred subtitle language for
DVD playback.
{ Disc Menu }
Select the preferred disc menu language
for DVD playback.
D Use
keys to select a language and

20
If the language you want is not

available in the list, select { Others }.
Use the numeric keypad (0-9) on the
remote control to enter the 4-digit
language code XXXX (see last page) and
E Repeat steps C ~ D for other settings.

Helpful Hints:
During DVD playback, you can switch the
audio and subtitle languages by pressing the
AUDIO and SUBTITLE buttons on the
remote control. However, this does not
change the default settings you have made
here.
For some DVDs, the subtitle/audio/menu
language can only be changed via the DVD
disc menu.
Setting the TV Display

Set the aspect ratio of this unit according
to the TV type you have connected. The
format you select must be available on
the disc. If it is not, the setting for TV
display will not affect the picture during
playback.

remote control.
B Press
repeatedly to select { Video

Setup Page }.
C Press
to highlight { TV Display } in
the menu and press .
Video Setup Page
TV Type
TV Display
Progressive
Picture Setting
Component
4:3 Pan Scan

4:3 Letter Box
16:9 Wide Screen
{ 4:3 Pan Scan }

Select this if you have a
conventional TV and
want both sides of the
picture to be trimmed or formatted
to fit your TV.
{ 4:3 Letter Box }
conventional TV. In this
case, a wide picture with
black bands on the upper and lower
portions of the TV will be displayed.
{ 16:9 Wide Screen }
wide-screen TV.
D Select one of the options and press OK

to confirm.
21
English

English
Setting up Progressive Scan

feature
(for Progressive Scan TV only)
The progressive scan displays twice the
number of frames per second than
interlaced scanning (ordinary normal TV
system). With nearly double the number
of lines, progressive scan offers higher
picture resolution and quality.
Before you start...
Ensure that you have connected this unit
to a progressive scan TV using the
Y Pb Pr connection (see Option 2:
Connecting to a Progressive Scan TV or
component video input).
A Turn on the TV to the correct viewing

channel for this unit.
Make sure that the TVs progressive
scan mode is turned off (or set to
interlaced mode). Refer to your TVs user
manual.
B Turn on this unit and press DISC/USB

on the remote control.
C Press SETUP on the remote control.

D Press
repeatedly to select { Video

Setup Page }.
Video Setup Page

TV Type
TV Display
Progressive
Picture Setting
Component
menu and press OK to confirm.
G Read the notification message on the TV

and confirm your action by selecting the
in the menu and press OK.
There will be no picture on your TV
at this state until you have turned
on the progressive scan mode on
your TV.
H Turn on your TV progressive scan mode,

refer to your TVs user manual.
A message appears on the TV.
I Confirm your action by selecting the

in the menu and press OK.
The setup is now completed and you
can start to enjoy the high quality picture.
If no picture is displayed
A Press OPEN/CLOSE .
on the remote control.
C Press AUDIO on the remote control.
Video Setup Page
YUV
RGB
E Move to { Component } > { YUV } in

the menu and press OK to confirm.
22
On
F Move to { Progressive } > { On } in the
B Press
TV Type
TV Display
Progressive
Picture Setting
Component
Off
Helpful Hints:
If a blank/distorted screen appears, wait
for 15 seconds for the auto recovery.
There are some progressive scan TVs that
are not fully compatible with this unit,
resulting in an unnatural picture when
playing back a DVD VIDEO disc in the
progressive scan mode. In such a case, turn
off the progressive scan feature on this unit
and your TV
.

E Use
You can adjust the delay times (centre

and surround only) and volume level for
individual speakers. These adjustments let
you optimise the sound according to
your surroundings and setup.
Before you start...
Stop the disc playback by pressing STOP
button twice or remove the disc from
the disc tray. Otherwise, the settings are
not accessible.

remote control.
repeatedly to select { Audio
Setup Page }.
C Press
to highlight { Speakers
Volume } and press .
Audio Setup Page

Speakers Volume
Speakers Delay
CD Upsampling
Speakers Level Setup
Front Left
Front Right
Center
Subwoofer
Rear Left
Rear Right
Audio Setup Page

Speakers Volume
Speakers Delay
CD Upsampling
Audio Sync
Speakers Distance Setup
Center
0ms
Rear Left
0ms
0ms
Rear Right
F Use
keys to set the delay times

(0 ms ~ 15 ms) for centre and rear
speakers that best suit your surround
sound needs.
G Press OK to confirm.
B Press
Audio Sync
English
keys to highlight { Speakers

Delay } and press .
Setting the speakers

channels
Helpful Hints:
A 1ms increase/decrease of delay time is
equivalent to 30 cm change in distance.
Use the longer delay time settings when
the rear speakers are closer to the listener
than the front speakers.
The test tone will be automatically
generated to help you judge the sound level
of each speaker.
0dB
0dB
0dB
0dB
0dB
0dB
D Use
keys to set the volume level for

each speaker (-6dB ~ +6dB) and press
OK to confirm.
23
Disc Operations
English
Playable discs
Your DVD home theatre system

plays:
Digital Versatile Discs (DVDs)
Video CDs (VCDs)
Super Video CDs (SVCDs)
Finalised DVD Recordable (DVDR),
DVD Rewritable (DVDRW)
Audio Compact Discs (CDs)
MP3/ Windows Media Audio discs,
picture (Kodak, JPEG) files on
CD-R(W)
ISO 9660/UDF format
JPEG resolution support up to
3072 x 2048
Supported sampling frequencies:
32 kHz, 44.1 kHz, 48 kHz
Supported Bit-rates: 32~256 (kbps),
variable bit rates (average 128 kbps)
DivX files on CD-R(W)/DVD+R(W):
DivX 3/4/5/6, DivX Ultra
Region Codes for DVD discs
DVD discs and players are designed with
regional restrictions. Before playing a disc,
make sure the disc is for the same region
as your player. The regional code for this
unit is indicated at the rear or bottom
panel.
24
Notes:
If the inhibit icon ( or X) appears
on the TV when a button is pressed,
it means the function is not
available on the current disc or at
the current time.
Never put any objects other than
discs on the disc tray. Doing so may
cause the disc player to malfunction.
Playing a disc
A Press SOURCE repeatedly until DISC
appears on the display panel (or press
DISC/USB on the remote control).
B Turn on the TV to the correct viewing

channel for this unit.
The blue DVD background screen
appears on the TV.
C Press OPEN/CLOSE to open the

disc tray.
D Load a disc and press OPEN/CLOSE

to close the disc tray.
Make sure the disc label is facing up.
For double-sided discs, load the side
which you want to play facing up.
E Playback starts automatically.

See the following pages for more
playback options and features.
Helpful Hints:
If you are having trouble playing a certain
disc, remove the disc and try a different one.
Improperly formatted discs cannot be played
on this unit.
Some discs cannot be played on this player
due to the configuration and characteristics
of the disc, or due to the condition of
recording and authoring software that was
used.
Basic playback controls

Pausing playback
During playback, press u.
While in pause mode, you can press
to step forward one frame at each
press.
To resume playback, press u again.
Selecting another track/chapter
Press / or use the numeric
keypad 0-9 to key in a track/chapter
number.
If the repeat track mode is active, press
again to replay the same track/chapter.
Searching backward/forward
Press m / M on the remote control.
While searching, press m / M
repeatedly to decrease/increase the
search speed.
To resume normal playback, press
u.
Stopping playback
Press x.
Helpful Hints:
If the message To playback from the
beginning, press PREV key appears on the
TV while you load in a disc, you can press
to start playback from the beginning.
This is a power-saving feature, this unit
automatically switches to standby mode if
you do not press any buttons within 15
minutes after a disc has stopped playing.
English
Disc Operations (continued)

Selecting various repeat/
shuffle functions
The available of the repeat play options
and shuffle play mode are vary depending
on the disc type.
While playing a disc, press
REPEAT on the remote control
repeatedly to choose a repeat or shuffle
play mode.
DVD
RPT ONE (repeat chapter)
RPT TT (repeat title)
SHUFFLE (random play)
RPT SHF (repeat random play)
RPT OFF (exit repeat mode)
VCD/SVCD/CD
RPT ONE (repeat track)
RPT ALL (repeat disc)
RPT SHF (repeat random play)
MP3/ DivX/ Windows Media Audio
RPT ONE (repeat track)
RPT ALL/FLD (repeat folder)
Helpful Hint:
Repeat playback is not possible on VCDs
when the PBC mode is turned on.
25

English
Programming disc tracks

(not for Picture CD/MP3 discs)
You can play the contents of the disc in
the order you want by programming the
playing order of the tracks.
A Press PROGRAM on the remote

control.
The programming menu appears.
Program: Track (01-16)
Other playback features

for video discs (DVD/VCD/
SVCD)
SLEEP
DISC MENU
TITLE
DISPLAY
SUBTITLE
AUDIO
ZOOM
6
7
2
12
8
9
10
Exit
Start
Next
AUDIO SYNC
B Use the numeric keypad (0-9) to

enter a valid track/chapter number.
C Use
keys to move the cursor to

the next position.
If there are more than ten total
programme tracks, select { Next } on
the screen and press OK (or press on
the remote control) to access the next
programming page.
To remove the track/chapter from the
programming menu, select the track/
chapter and press OK.
D Once complete, select { Start } on the

screen and press OK to start playback.
Playback starts from the selected track
under the programmed sequence.
E To exit the programme menu, select

{ Exit } in the menu and press OK.
26
Note:
The operating features described here
might not be possible for certain discs.
Always refer to the instructions supplied
with the discs.
Using the Disc Menu
Depending on the disc format, a menu
may appear on the TV screen once you
load the disc.
To select a playback feature or item
Use
keys or numeric keypad
0-9 on the remote control, then press
OK to start playback.
To access or remove the menu
Press DISC MENU on the remote
control.
Viewing playback information

This unit can display the disc playback
information (for example, title or chapter
number, elapsed playing time, audio/
subtitle language) and a number of
operations can be done without
interrupting disc playback.
A During playback, press DISPLAY.

A list of available disc information
appears on the TV.
DVD
Zooming in/out
This option allows you to zoom in or out
the picture on the TV and to pan through
the picture.
A During playback, press ZOOM

repeatedly to select a different zoom
factor.
Playback continues.
B Use
keys to pan through the

zoomed image.
C Press ZOOM repeatedly to return to
Menu
the original size.
Title
01/01
Chapter
02/99
Audio
2ch
Subtitle
Off
Bitrate 7
Title Elapsed
Changing subtitle language
Chi
This operation works only on DVDs with

multiple subtitle languages. You can
change the language you want while
playing a DVD.
VCD/SVCD
Menu
Track
Disc Time
Track Time
Repeat
09/16
1:16:05
0:04:32
Off
Bitrate 8
Total Elapsed
Press SUBTITLE repeatedly to select

different subtitle languages.
Switching camera angles
B Use
keys to view the information

and press OK to access.
C Use the numeric keypad 0-9 to input

the number/time or use
make the selection.
keys to
D Press OK to confirm.
Playback changes according to the
chosen time or to the selected title/
chapter/track.
This option is only available on DVDs

that contain sequences recorded from
different camera angles. This allows you
to view the picture from different angles.
A During playback, press DISPLAY.

Playback information menu appears.
B Press
to highlight ANGLE function in

the menu.
C If different camera angles choices are

available, press
select.
and numeric keys to
27
English

English
Changing sound track language

This operation works only on DVDs with
multiple sound track languages, or VCDs
with multiple audio channels.
Press AUDIO repeatedly to select the
available audio languages.
For VCD changing the audio
channel
Press AUDIO repeatedly to select the
available audio channels provided by the
disc (STEREO, MONO LEFT, MONO
RIGHT or MIX MONO).
Setting the delay times for audio
playback
This feature allows you to adjust the
audio delay times if the video playback is
slower than the audio output streams,
hence resulting in Lip-sync. The only
way to correct Lip-sync error caused by
delayed video is to delay audio by an
equal amount.
A Press AUDIO SYNC.

B Within five seconds, use the VOL +to set the audio output delay times
(0 ~ 200 ms).
If the volume control is not used
within five seconds, it resumes its normal
volume control function.
Helpful Hint:
Set your preferred default AUDIO SYNC
setting in the setup menu, see Setup Menu
Options - { Audio Setup Page }.
28
Playback Control (VCD only)

Playback Control (PBC) playback allows
you to play Video CDs interactively,
following the menu on the display. The
PBC feature on this unit is turned on by
default.
For VCDs with Playback Control
(PBC) feature (version 2.0 only)
During playback, press TITLE to
return to the disc title menu or main
menu.
Helpful Hint:
Set your preferred default PBC setting in
the setup menu, see Setup Menu Options { Preference Page }.
Preview function (VCD/SVCD only)

This function allows you to preview the
contents of a VCD/SVCD.
A Press DISC MENU.
To go to the previous or next page, press

/ .
To return to the main menu, select
{ Menu } on the screen and press OK.
Press OK on the selected thumbnail
picture to start playback from there.
Select Digest Type:
Track Digest
Disc Interval
Track Interval
C To exit the preview menu, select

{ Exit } on the screen and press OK.
B Use

following options and press OK.
{ Track Digest }
View six different tracks on one screen
each time. It allows you to have a quick
glance at all the tracks on the disc.
{ Disc Interval }
View the whole disc in six thumbnail
pictures. It divides a disc into six portions
at regular intervals and displays them on
one screen.
{ Track Interval }
View the content of a single track in six
thumbnail pictures. It divides a single
track into six portions at regular intervals
and displays them on one screen.
This option is only available during
playback mode.
01
02
03
04
05
06
Exit
Menu
29
English

English
Playing a MP3/ WMA disc

This unit can playback most of the MP3
and Windows Media Audio files
recorded on a recordable disc or
commercial CD.
Before you start ...
Turn on your TV to the correct Video In
channel. See Finding the correct viewing
channel for details.
A Insert a MP3/WMA disc.

The disc reading time may exceed 30
seconds due to the complexity of the
directory/file configuration.
The disc menu appears on the TV.
00:06
04:04
001/018
\UDF_MP3\
Previous
08-AudioTrack
09-AudioTrack
10-AudioTrack
11-AudioTrack
12-AudioTrack
13-AudioTrack
14-AudioTrack
000
018
000
Disc
B If the disc main menu contains various

folders, use
keys to select a desired
folder and press OK to open the folder.
C Use
keys to select a track/file and

press OK to start playback.
Playback starts from the selected file
and continue through to the end of the
folder.
30
During playback;
Press / to playback another track/
file in the current folder.
Press m / M to fast reverse/forward
search for a music track.
To select another folder from the
current disc, press
repeatedly to
highlight Previous folder and press OK
to return to the root menu.
Press REPEAT repeatedly to access
various play modes.
D To stop playback, press x.

Helpful Hints:
To skip the folders menu when you load a
MP3/JPEG disc, set the MP3/JPEG NAV
setting in the Preference Setup Page to
{ Without Menu }.
Only the first session of a multi-session CD
will be played back.
It is normal to experience an occasional
skip while listening to your MP3/WMA disc
due to poor clarity of digital contents during
internet downloading.
If any special characters are present in the
MP3/WMA track name (ID3) or album
name, it might not be displayed correctly on
the screen because this unit does not support
the characters.
Playing a JPEG image file

(slide show)
Turn on your TV to the correct Video In
channel. See Finding the correct viewing
channel for details.
Insert a JPEG photo CD (Kodak Picture
CD, JPEG).
For a Kodak disc, the slide show
begins automatically.
For a JPEG disc, the picture menu
appears on the TV. Press u to start the
slide-show playback.
Helpful Hint:
It may require longer time for this unit to
display the disc content on the TV due to the
large number of songs/pictures compiled into
one disc.
Supported file format:
The file extension has to be *.JPG and
not *.JPEG.
This unit can only display digital camera
pictures according to the JPEG-EXIF
format, typically used by almost all digital
cameras. It cannot display Motion JPEG,
progressive JPEG and other JPEG
formats, or pictures in formats other
than JPEG, or sound clips associated with
pictures.
Preview function
A During playback, press x.

12 thumbnail pictures will be displayed
on the TV.
B Press / to display the other

pictures on the previous/next page.
C Use

pictures and press OK to start playback.
D Press DISC MENU to return to Picture

CD menu.
Zoom picture
A During playback, press ZOOM

repeatedly to select a different zoom
factor.
B Use
keys to pan through the

zoomed image.
Rotating/flipping the picture

During playback, use
keys to
rotate/flip the picture on the TV.
: flip the picture vertically
: flip the picture horizontally
: rotate the picture anti-clockwise
: rotate the picture clockwise
31
English

English
Playing MP3/WMA music and

JPEG pictures simultaneously
You can create a musical slide show if the
disc contains both the MP3/WMA music
and JPEG picture files.
A Insert a MP3/WMA disc that contains

music and pictures.
B Select a track in the menu and press OK

to start playback.
C During music playback, use
keys to
select a picture file from the disc menu
and press OK.
The picture files will be played back
through to the end of the folder.
The music keeps playing back and will
be repeated if reaches the end of the
selected album, playlist or track.
D To stop simultaneous playback, press

DISC MENU followed by x.
Playing a DivX disc

This unit supports the playback of DivX
movies which you can copy from your
computer onto a recordable disc. See
Setup Menu Options - { General Setup
Page - DivX(R) VOD code } for details.
A Insert a DivX disc.

B Use
keys to navigate to the

title you want to play.
C Press OK to start playback.

During playback;
If the DivX disc has multilingual subtitles,
you can press SUBTITLE on the
remote control to change the subtitle
language.
If the DivX title has different audio
tracks, you can press AUDIO on the
remote control to change the audio
stream.
Use m / M keys on the remote
control to perform fast reverse/forward
search.
Press DISPLAY repeatedly until the
Time Search menu appears, key in the
time where playback should start.
Playback skips to the time entered.
Helpful Hints:
Subtitle files with the following file name
extensions (.srt, .smi, .sub, .ssa, .ass) are
supported but do not appear on the file
navigation menu.
The subtitle file name has to be the same
as the file name of the movie.
The subtitle can only be displayed up to an
average of 45 characters.
32
2007-04-26 10:53:25 AM
Playing from USB flash drive

or USB memory card reader
You can play or view the data files (JPEG,
MP3, Windows Media Audio or DivX)
in the USB flash drive or USB memory
card reader. However, editing or copying
the data file is not possible.
D Select the file to play and press u.

For more playback information, see
Playing a MP3/WMA disc, Playing a JPEG
image file (slideshow) or Playing a DivX
disc for details.
During playback, you can press
DISC/USB to return to the disc mode.
E Before removing the USB device, press x

to stop playback or press DISC/USB to
switch to disc mode.
Helpful Hints:
The USB socket does not support the
connection of other USB devices except to a
USB flash drive / USB memory card reader.
When the USB device does not fit into the
USB socket, a USB extension cable is
required.
You can only read and playback the
content from the USB device.
Copy-protected contents are not playable.
A Connect the USB flash drive / USB

memory card reader directly to the USB
socket on this unit.
B A message appears on the TV for 5 (five)

seconds when the device is detected.
Press DISC/USB to select device
C Press DISC/USB on the remote control

to access the data in the drive.
When using multiple drives on a single
card reader, only one of the connected
cards can be accessed.
The device numbers may vary from
different card readers.
33
English
Playback - USB Device
Playback - Other Audio Player

English
Playing from other portable

audio player
Connect your portable audio player to
this unit to get the best immersion sound
experience through the speaker system.
However, controlling of playback is only
possible on the portable audio player.
Side view
of Main unit
A Use the supplied MP3 LINE-IN cable to

connect between the headphone output
socket on your portable audio player and
the MP3 LINE-IN socket on this unit.
B Press MP3 LINE-IN on the remote

control.
C Start playback on your portable audio

player.
The music will be heard through the
speakers.
D To stop playback, press the STOP button

on the portable audio player.
Helpful Hint:
If you change the input source by pressing
any of the source buttons (e.g. DISC/USB,
RADIO), press the STOP button on the
portable audio player to stop its playback.
34
Accessing the setup menu

This system setup is carried out via the
TV, enabling you to customise this unit to
suit your particular requirements.
English
Setup Menu Options

General Setup Page
Disc Lock
Display Dim
Program
OSD Language
Screen Saver
Sleep
DivX(R) VOD Code
see page 36
SLEEP
SETUP
OK
Audio Setup Page

Speakers Volume
Speakers Delay
CD Upsampling
see page 37
Audio Sync
remote control.
The setup menu appears.
B Use
keys to select one of the setup

menu options and press OK.
Video Setup Page
If you are not able to access the

{ Preference Page }, press SETUP to
exit the menu. Then, press STOP x
twice before you press the SETUP
again.
C Use
and press
TV Type
TV Display
Progressive
Picture Setting
Component
see pages
38~39
keys to select a setup option

to access.
D Select the setting you wish to change and

press OK to confirm and go back to the
previously selected item.
Instructions and explanations of the
options are provided in the following
pages.
If the option in the menu is grayed
out, that means the setting is not
available or cannot be changed in the
current state.
Preference Page
Audio
Subtitle
Disc Menu
Parental
Surround
PBC
MP3/JPEG Nav
Password
DivX Subtitle
Default
see pages
40~41
E To exit, press SETUP.
35
Setup Menu Options (continued)

English
General Setup Page (underlined options are the factory default settings)
Disc Lock
Not all discs are rated or coded by the disc maker. You can
prevent play of specific discs with the disc lock function. Up to 40
discs can be locked.
{ Lock }
To block the playback of the current disc.
Subsequent access to a locked disc requires a
six-digit password. The default password is
136900 (see Preference Setup Page { Password }).
{ Unlock }
All discs can be played.
Display Dim
Select the brightness of this units display panel.

{ 100% }
Full brightness.
{ 70% }
Medium brightness.
{ 40% }
Dimmest display. This switches off all LEDs and
icons on the front display panel of this unit.
Program
Access the track programming menu. See Programming disc

tracks for details.
OSD Language
Select the menu language for this units on-screen display.
Screen Saver
The screen saver prevents damage to the TV screen by avoiding

exposure to a static image for too long.
{ On }
Switch to TV screen saver mode when
playback has been stopped or paused for
more than 5 minutes.
{ Off }
Turn off the screen saver function.
Sleep
The sleep timer enables the unit to switch to standby mode

automatically after the selected preset time.
{ 15/30/45/60 mins } Select the preset minutes for switching
the unit to standby mode automatically.
{ Off }
Turn off the sleep mode function.
DivX(R) VOD Code
Philips provides you with the DivX VOD (Video On Demand)

registration code that allows you to rent or purchase videos from
DivX VOD service at www.divx.com/vod. All the downloaded
videos from DivX VOD can only be played back on this unit.
Press
36
to see the registration code and press OK to exit.
English

Audio Setup Page (underlined options are the factory default settings)
Speakers Volume
Access the speakers level setup menu. Use

keys to adjust
the volume level for each connected speaker between -6dB to
+6dB. See Getting Started - Setting the speakers channels.
Speakers Delay
Access the speakers distance setup menu. Use

keys to set
the delay times for the centre and rear speakers based on the
listening position and distance. See Getting Started - Setting
the speakers channels.
Note: 1 ms increase/decrease of delay time is equivalent to one (1) foot
change in distance. Use the longer delay time settings when the rear
speakers are closer to the listener than the front speakers.
CD Upsampling
This feature enables you to convert the music CD to a

higher sampling rate using sophisticated digital signal
processing for better sound quality.
{ Off }
Turn off CD-upsampling.
{ 88.2 kHz (X2) } To convert the sampling rate of the CDs
twice as high as the original rate.
Notes:
If you have activated the CD upsampling feature, the audio output
automatically switches to stereo mode.
If you press the SURROUND button on the remote control to select
multi-channel mode, it turns off the CD upsampling feature.
Audio Sync
This feature allows you to adjust the audio delay times if the
video playback is slower than the audio output streams.
Use
keys to set the delay times for the audio output
between 0~200ms.
37

English
Video Setup Page (underlined options are the factory default settings)
TV Type
Select the colour system that matches the connected TV. It

enables playback of a different type of disc (PAL or NTSC disc)
on this unit.
{ PAL }
For PAL-system TV.
{ NTSC }
For NTSC-system TV.
{ Multi }
For TV that is compatible with both PAL and
NTSC.
TV Display
The picture shape can be adjusted to fit your TV.

{ 4:3 Pan Scan } For a full-height picture with
the sides trimmed.
{ 4:3 Letter Box } For a wide-screen display
with black bars on the top and
bottom.
{ 16:9 Wide Screen } For wide-screen TV
(frame ratio 16:9).
Progressive
38
Before enabling the progressive scan feature, you must ensure that
your TV can accept progressive signals (a progressive scan TV is
required) and that you have connected this unit to your TV using
the Y Pb Pr. See Getting Started - Setting up progressive scan
feature for details.
{ On }
Turn on progressive scan mode.
Read the instructions on the TV and confirm
your action by pressing OK on the remote
control.
{ Off }
Turn off the progressive scan mode.
English

Video Setup Page (underlined options are the factory default settings)
Picture Setting
This unit provides three predefined sets of picture colour

settings and one personal setting which you can define yourself.
{ Standard }
{ Bright }
{ Soft }
{ Personal }
Personal Picture Setup

Brightness
Contrast
Tint
Color
Component
Original colour setting.

Vibrant colour setting.
Warm colour setting.
Select this to personalise the picture colour
setting. Use
keys to adjust to the setting
that best suits your personal preference and
press OK to confirm. For an average setting,
select { 0 }.
Select the type of video output that matches the video

connection between this unit and your TV.
{ YUV }
For component video (Y Pb Pr) connection.
{ RGB }
For SCART connection.
39

English
Preference Page (underlined options are the factory default settings)

Audio
Select the preferred audio language for DVDs with multiple

sound tracks.
Subtitle
Select the preferred subtitle language for DVD playback.
Disc Menu
Select the preferred disc menu language for DVD playback.

Note: If the selected audio/subtitle/disc menu language is not available on
the DVD, the discs default language will be used instead.
Parental
This is to prohibit viewing of discs that had exceeded the limits

you set. It works only on the DVDs with parental level assigned
to the complete disc or to certain scenes on the disc.
1) Use
keys to select a rating level from 1 to 8 and press OK.
2) Use the numeric keypad 0-9 on the remote control to enter your
six-digit password.
Notes:
The ratings are country-dependent (1 is considered material that is
least offensive and 8 is most offensive). To disable parental controls and
allow all discs to play, select 8.
Some DVDs are not encoded with a rating though the movie rating
may be printed on the disc cover. The rating level feature does not
prohibit playback of such discs. VCD, SVCD and CD have no level
indication, so parental control has no effect on these type of discs.
DVDs that are rated higher than the level you selected will not be
played unless you enter the same six-digit password.
Surround
Set the preferred surround setting when the unit is powered up.
{ On }
Turn on to multi-channel surround mode.
{ Last Setting } Turn on to the last surround setting.
PBC
Play Back Control feature is applicable for VCD/SVCD only. It

allows you to play Video CDs (2.0) interactively, following the
menu on the display.
{ On }
The index menu (if available) appears on the
TV when you load a VCD/SVCD.
{ Off }
The VCD/SVCD skips the index menu and
playback directly from the beginning.
40
Preference Page (underlined options are the factory default settings)

MP3/JPEG Nav
MP3/JPEG Navigator can only be set if the disc is recorded with a

menu. It allows you to select different display menus for easy
navigation.
{ Without Menu } Display all the files contained in the MP3/
Picture disc.
{ With Menu } Display the folder menu of the MP3/Picture
disc.
Note: This unit can only display 650 files/folder in the directory.
Password
The password is used for the Disc Lock and Parental. The default
password is 136900. To change the password:
1) Press OK to access the change password menu.
Change Password
Old Password
New Password
Confirm PWD
OK
2) Use the numeric keypad 0-9 on the remote control to

enter your existing six-digit password at { Old Password }.
Note: When doing this for the first time or if you forget your existing
password, key in 136900.
3) Enter the new six-digit password at { New Password }.

4) Enter the new six-digit password again at { Confirm PWD }.
5) Press OK to confirm and exit the menu.
DivX Subtitle
Select the font type that supports the recorded DivX subtitle.
{ Central Europe } Display Central Europe fonts.
{ Cyrillic }
Display Cyrillic fonts.
{ Greek }
Display Greek subtitle fonts.
{ Standard }
Display a standard list of Roman subtitle
fonts provided by this unit.
{ Hebrew }
Display Hebrew subtitle fonts.
{ Chinese (Simp) } Display Simplified Chinese fonts.
{ Korean }
Display Korean fonts.
Default
This feature enables you to reset all the setup menu options and
your personal settings to the factory defaults, except your
password for the Disc Lock and Parental.
Press OK to confirm the default reset.
41
English
Radio Operations
English

Make sure the FM and AM/MW antennas
are connected.
Tuning to radio stations

A Press SOURCE repeatedly until FM
appears on the display panel (or press
RADIO on the remote control).
B Press
/ on the remote control to

start tuning.
The frequency indication starts to
change until a radio station with sufficient
signal strength is found.
C Repeat step B if necessary until you find
Presetting radio stations

You can store up to 40 FM and 20
AM/MW preset radio stations in the
memory. There are three different ways
to program the radio stations:
Using auto install (for first time setup
only)
Using automatic preset
Using manual preset
Helpful Hints:
This unit exits presetting mode if no
button is pressed within 20 seconds.
If no stereo signal is detected or less than
5 (five) stations are detected during radio
installation, CHECK ANTENNA appears.
the desired radio station
D To fine-tune the reception of a weak

station, press
/
briefly and
repeatedly until an optimal reception is
found.
Helpful Hint:
If the FM radio station is transmitting RDS
(Radio Data System) data, the RDS name
will be displayed and stored.
Using auto install

When you access the RADIO mode for
the very first time, you will be prompted
to install the radio stations. With this
feature, you can install all the available
radio station automatically with one
touch of button.
RADIO
SLEEP
A Press RADIO.
AUTO INSTALL ... PRESS PLAY
appears.
42
B Press u.
This unit starts searching from the FM
band followed by the AM/MW band.
All the available radio stations with
strong signal will be stored automatically.
Once complete, the first tuned radio
station will be played back.
Using automatic preset
Use automatic presetting to store or
reinstall all the preset radio stations.
SLEEP
RADIO
PROGRAM
English
Radio Operations (continued)

Selecting a preset radio
station
A Press RADIO to select FM or
AM/MW band.
B Use / keys to select a preset radio

stations (or use the numeric keypad on
the remote control).
The preset number and radio
frequency appear on the display panel.
Deleting a preset radio

station
A In radio mode, use / keys to select
a preset radio station.
B Press and hold x until FM/AM/MW X

A Press RADIO to select FM or AM/
MW band.
B Press and hold PROGRAM until

START ... appears on the display panel.
All previously stored radio stations
will be replaced.
DELETED appears.
X is the preset number.
The radio station continues to play
but has been deleted from the preset list.
The rest of the preset radio stations
remain unchanged.
Using manual preset

Use manual presetting to store your
favourite radio stations.
A Tune to your desired radio station (see

Tuning to radio stations).
B Press PROGRAM.
C Use / keys to select a preset
number that you want to store the
current radio station.
D Press PROGRAM to store.
43
Sound and Volume Controls

English
Selecting digital sound effects

SLEEP
Select a preset digital sound effect that

matches your discs content or that
optimises the sound of the musical style
you are playing.
MUTE
VOL+SURROUND
SOUND
Press SOUND to select the available

sound effect.
Movies
Music
Description
CONCERT
CLASSIC
Flat and pure sound mode.

Ideal for listening to classical
music and watching live
concert DVDs.
DRAMA
JAZZ
Clear mid and high range.

Recreates the atmosphere of a
live club with the artist just in
front of you. Good for Jazz
music and watching dramas.
ACTION
ROCK
Enhanced low and high range

for great sounding movie
effects and atmosphere. Great
for action movies and rock/pop
music.
MTV
RnB
Enhanced low and mid range

for groovy and punchy sounds.
Suitable for R&B, Hip Hop and
MTV videos.
GAMING
PARTY
Slightly enhanced low range

and strong mid range ideal for
party music and video gaming.
CARTOON
LOUNGE
Moderate sound mode suitable

for lounge music and watching
cartoons.
SPORTS
SPORTS
Moderate mid range and

surround effects for clear
vocals and the atmosphere of a
live sports venue.
NEWS
NEWS
Enhanced mid range for clear

vocals/speech.
NIGHT
NIGHT
Dynamically controlled sound

mode suitable for watching
movies at night or for nonintrusive background music.
Volume control
Press VOL +/- to increase or
decrease the volume level.
VOL MIN is the minimum volume
level and VOL MAX is the maximum
volume level.
To turn off the volume temporarily
Press MUTE %.
Playback continues without sound and
MUTE appears.
To restore the volume, press MUTE
% again, or increase the volume level.
Selecting surround sound

Press SURROUND to select between
Multi-Channel or Stereo sound.
The availability of the various
surround sound modes depends on the
sound available on the disc.
The available output modes for
Multi-channel include: Dolby Digital, DTS
(Digital Theatre Systems) Surround and
Dolby Pro Logic II.
Stereo broadcasts or recordings will
produce some surround channel effects
when played in a surround mode.
44
Installing the latest software
Setting the Sleep timer
Periodically Philips will issue software

upgrades to enhance the user experience.
The sleep timer enables this unit to

switch to standby mode automatically at
a preset time.
A Get the software version of this unit by

pressing OPEN/CLOSE to open the
disc compartment.
B Press DISPLAY on the remote control.

Write down the information for your
current software version.
C Visit the Philips website

www.philips.com/support to check the
availability of the latest software upgrade
and download the software to a CD-R.
D Insert the CD-R to the disc tray.

The software starts to install on this
unit automatically.
Press SLEEP on the remote control

repeatedly to select a preset switch-off
time. (15, 30, 45, 60 minutes or OFF).
Before this unit switches to the
standby mode, a countdown of 60
seconds is displayed.
SLEEP 60 SLEEP 59 ....
SLEEP1 SLEEP
To cancel the sleep timer
Press SLEEP repeatedly to select OFF
or press the 2 (STANDBY-ON)
button.
Note:
Never unplug or turn off this unit
during the upgrade.
E When the disc compartment opens,

remove the CD-R.
The software upgrading is in process.
F Once complete, it turns off to standby

mode automatically.
45
English
Other Features
Troubleshooting
English
WARNING
Under no circumstances should you try to repair the system yourself, as this will
invalidate the warranty. Never open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair.
If you are unable to solve a problem by following these instructions, consult your dealer or
Philips for help.
Problem (General)
Solution
No power.
Press STANDBY-ON on the unit to turn on the

power.
Make sure the mains cord is properly connected and
the AC outlet has power.
No picture.
Refer to your TVs manual for correct Video In

channel selection. Change the TV channel until you
see the DVD screen.
Press DISC/USB to select disc mode.
If this happens when you turn on the progressive scan
feature, wait for 15 seconds for the auto recovery or
switch back to the default mode as below:
1) Press OPEN/CLOSE .
2) Press on the remote control.
3) Press AUDIO on the remote control.
Completely distorted picture

or black/white picture.
Check the video connection.

Sometimes a small amount of picture distortion may
appear. This is not a malfunction.
The disc is dirty. Clean the disc.
No sound or distorted sound.
Adjust the volume.

Check the speaker connections and settings.
Make sure that the audio cables are connected and
press SOURCE to select the correct input source (for
example, TV or AUX/DI) to choose the device that
you want to hear through this unit.
No surround sound effect

from the speakers.
Press SURROUND to select a correct surround

sound setting.
Make sure that the source you are playing is recorded
or broadcast in surround sound (DTS, Dolby Digital,
etc).
The remote control does not

function properly.
Select the source you want to play (for example,

DISC/USB or RADIO) before pressing the function
button ( , / ).
Reduce the distance between the remote control and
this unit.
Batteries are weak, replace the batteries.
Point the remote control directly toward the IR sensor.
46
Troubleshooting (continued)
The unit does not start
playback.
Solution
English
Problem (Playback)
Insert a readable disc with the playback side facing

down. The DVD+R/CD-R must be Finalised.
Make sure the disc is not scratched or warped.
Press SETUP to turn off the system setup menu
screen.
You may need to enter the password in order to
unlock the disc for playback.
Moisture may have condensed inside this unit.
Remove the disc and leave this unit turned on for
about an hour.
The aspect ratio of the screen The aspect ratio is fixed on the DVD disc.
cannot be changed even
Depending on the TV, it may not be possible to
though you have set the TV
change the aspect ratio.
display.
Cannot activate some features The features may not be available on the DVD.
e.g. Angles, Subtitles, or
Changing the language for the sound or subtitle is
multi-language Audio.
prohibited on this DVD.
Not able to select some items Press STOP button twice before selecting the system
in the setup/system menu.
setup menu.
Depending on the disc availability, some menu items
cannot be selected.
Unable to play DivX movies.
Ensure that the DivX file is encoded according to the

Home Theatre Profile with the DivX encoder.
Check that the DivX movie downloaded is a complete
file.
Radio reception is poor.
If the signal is too weak, adjust the antenna or

connect an external antenna for better reception.
Increase the distance between this unit and your TV
or VCR.
Tune in to the correct frequency.
Place the antenna further away from any equipment
that may be causing the interference.
The unit does not work.
Disconnect the power cord from the power outlet

for a few minutes. Reconnect the power cord and try
to operate again as usual.
47
Troubleshooting (continued)
English
Problem (USB)
Solution
The contents of the USB flash The USB flash drive format is not compatible with this
drive cannot be read.
unit.
Drive is formatted with a different file system which is
not supported by this unit (e.g. NTFS).
Slow operation of the USB
flash drive.
48
Large file size or high memory USB flash drive takes

longer time to read and display on the TV.
Why does it take so long to display the

contents on my USB device?
This could be due to the large numbers
of files (>500 files/folders) or size of the
files (>1MB).
There could be other non-supported files
in the device that this unit is trying to
read/display.
What if un-supported devices (e.g. USB
mouse, keyboards) are plugged into
this unit?
The device may cause this unit to be
unstable. Remove the unsupported device
and unplug the mains cord. Wait for a few
minutes before reconnecting the mains cord
and power on this unit again.
What happens when I plug in a USB
HDD?
HDD is not supported as the large storage
capacity makes navigation very difficult.
Transfer the music files (mp3) and photos
(jpg) into a flash drive.
Why does this unit fail to detect my
USB portable music player?
The portable music player may require
propriety software that is bundled with our
system in order to access the contents (eg.
playlist). MTP class not supported, only can
support mass storage class devices.
What types of file does this unit
support?
We support only FAT16 and FAT32, not
NTFS.
Why does the file name appear to be

different from what was displayed on my
computer (e.g. from Good Bye. jpg to
Good_B~1.jpg)?
The length of the file name is restricted
by the file system of the device (FAT16),
which only supports eight (8) characters.
The computer may be able to display the
full file name as the operating system can
convert the file system.
Is simultaneous USB and Disc playback
possible?
This is not possible due to memory
limitation. In addition, a different user
interface will be needed in order to function
and in order to be simple enough to use.
Why cant I rotate the pictures in my
device?
In order to rotate the pictures in the USB
device, the picture must contain EXIF
information, stored by most digital cameras.
This EXIF information may have been
removed when you edit or copy the picture
from other devices using editing
programmes.
Why cant this unit play some of my
music files, photos or movies?
The music files may not be playable because
of different formats and encoding bit-rates.
Similarly, the photos may be of low
resolution or too high resolution for this unit
to support.
49
English
Frequently Asked Questions (USB)
Glossary
English
Analogue audio: Sound that has not been

turned into numbers. Analogue sound is
available with you use the AUDIO LEFT/
RIGHT. These red and white sockets send
audio through two channels, the left and
right.
Aspect ratio: Aspect ratio refers to the
length to height ratio of TV screens. The
ratio of a standard TV is 4:3, while the ratio
of a high-definition or wide TV is 16:9. The
letter box allows you to enjoy a picture with
a wider perspective on a standard 4:3 screen.
AUDIO OUT sockets: Red and white
sockets on the back of the unit that send
audio to another system (TV, Stereo, etc)..
Bit Rate: The amount of data used to hold
a given length of music; measured in kilobits
per second, or kbps. Or, the speed at which
you record. Generally, the higher the bit
rate, or the higher the recording speed, the
better the sound quality. However, higher bit
rates use more space on a disc.
Chapter: Sections of a picture or a music
piece on a DVD that are smaller than titles.
A title is composed of several chapters. Each
chapter is assigned a chapter number
enabling you to locate the chapter you want.
Disc menu: A screen display prepared for
allowing a selection of images, sounds,
subtitles, multi-angles, etc., recorded on a
DVD.
DivX: The DivX code is a patent-pending,
MPEG-4 based video compression
technology, developed by DivX Networks,
Inc., that can shrink digital video to sizes
small enough to be transported over the
internet, while maintaining high visual quality.
50
Dolby Digital: A surround sound system

developed by Dolby Laboratories containing
up to six channels of digital audio (front left
and right, surround left and right, centre and
subwoofer).
Dolby Surround Pro Logic II: It is an
improved matrix decoding technology that
provides better spatiality and directionality
on Dolby Surround programme material,
provides a convincing three dimensional
sound field on conventional stereo music
recordings and is ideally suited to bring the
surround experience to automotive sound.
While conventional surround programming
is fully compatible with Dolby Surround Pro
Logic II decoders, soundtracks will be able to
be encoded specifically to take full advantage
of Pro Logic II playback, including separate
left and right surround channels. (Such
material is also compatible with conventional
Pro Logic decoders).
DTS: Digital Theatre Systems. This is a
surround sound system, but it is different
from the Dolby Digital. The formats were
developed by different companies.
JPEG: A very common digital still picture
format. A still-picture data compression
system proposed by the Joint Photographic
Expert Group, which features small decrease
in image quality in spite of its high
compression ratio. Files are recognised by
their file extension JPG or JPEG.
MP3: A file format with a sound data
compression system. MP3 is the
abbreviation of Motion Picture Experts
Group 1 (or MPEG-1) Audio Layer3. By
using the MP3 format, one CD-R or CD-RW
can contain about 10 times more data than a
regular CD.
Glossary (continued)
English
MPEG: Motion Picture Experts Group. A

collection of compression systems for digital
audio and video.
Multi-channel: DVDs are formatted to
have each sound track constitute one sound
field. Multi-channel refers to a structure of
sound tracks having three or more channels.
PBC: Playback Control. A system of
navigating a Video CD/Super VCD through
on-screen menus recorded onto the disc.
You can enjoy interactive playback and
searching.
Progressive Scan: The progressive scan
displays twice the number of frames per
second than in an ordinary TV system. It
offers higher picture resolution and quality.
Region code: A system allowing discs to be
played only in the region designated. This
unit will only play discs that have compatible
region codes. You can find the region code
of your unit by looking at the product label.
Some discs are compatible with more than
one region (or ALL regions).
Surround: A system for creating realistic
three dimensional sound fields full of realism
by arranging multiple speakers around the
listener.
Title: The longest section of a movie or
music feature on DVD. Each title is assigned
a title number, enabling you to locate the
title you want.
WMA: Windows Media Audio. Refers to
an audio compression technology developed
by Microsoft Corporation. WMA data can be
encoded by using Windows Media Player
version 9 or Windows Media Player for
Windows XP. Files are recognised by their
file extension WMA.
51
Specifications
English
AMPLIFIER
MAIN UNIT
Total output power Home Theatre mode: 300 W

Frequency Response: 180 Hz 18 kHz / 3 dB
Signal-to-Noise Ratio: > 60 dB (A-weighted)
Input Sensitivity
- AUX In :
500 mV
- TV In:
250 mV
- MP3 Line-In:
500 mV
Power Supply Rating: 220~240 V; 50 Hz

Power Consumption: 60 W
Dimensions:
360 x 48 x 332 (mm)
(w x h x d)
Weight:
2.82 kg
RADIO
Tuning Range:
FM 87.5108 MHz (50kHz)

MW 5311602 kHz (9kHz)
26 dB Quieting
Sensitivity:
FM 22 dBf, MW 5000V/m
IF Rejection Ratio:
FM 60 dB, MW 24 dB
Signal-to-Noise Ratio: FM 50 dB, MW 30 dB
MW Suppression Ratio: FM 30 dB
Harmonic Distortion: FM Mono 3%
FM Stereo 3%
MW 5%
Frequency Response FM 180 Hz10 kHz / 6 dB
Stereo Separation
FM 26 dB (1 kHz)
Stereo Threshold
FM 23.5 dB
FRONT AND REAR SPEAKERS

System:
Impedance:
Speaker drivers:
Frequency response:
Dimensions:
Weight:
CENTRE SPEAKER
System:
Impedance:
Speaker drivers:
Frequency response:
Dimensions:
Weight:
DISC
SUBWOOFER
Laser Type
Disc Diametre
Video Decoding
Impedance:
Speaker drivers:
Frequency response:
Dimensions:
Semiconductor
12cm / 8cm
MPEG-1 / MPEG-2 /
/ DivX 3/4/5/6, Ultra
Video DAC
12 Bits
Signal System
PAL / NTSC
Video Format
4:3 / 16:9
Video S/N
56 dB (minimum)
Audio DAC
24 Bits / 96 kHz
Frequency Response 4 Hz20 kHz (44.1 kHz)
4 Hz22 kHz (48 kHz)
4 Hz44 kHz (96 kHz)
PCM
IEC 60958
Dolby Digital
IEC 60958, IEC 61937
DTS
IEC 60958, IEC 61937
Full range satellite

4
3 full range speaker
150 Hz 20 kHz
95.5 x 198 x 75 (mm)
(w x h x d)
0.46 kg/each
Weight:
Full range satellite

8
3 full range speaker
150 Hz 20 kHz
240 x 99.5 x 64 (mm)
(w x h x d)
0.77 kg
8
165 mm (6.5) woofer
40 Hz 150 Hz
131 x 315 x 386 (mm)
(w x h x d)
3.97 kg
Specifications subject to change without prior

notice.
52
2007-04-26 10:53:25 AM
53

Home Cinema

Uploaded by

Copyright:

Available Formats

Home Cinema

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Home Cinema

Uploaded by

Copyright:

Available Formats

DVD HOME THEATRE SYSTEM

Manual del usuario

Important notes for users in the

1 Remove fuse cover and fuse.

Philips Consumer Electronics

2 Fix new fuse which should be a BS1362

3 Refit the fuse cover.

How to connect a plug

Copyright in the U.K.

This product complies with the radio

Disposal of your old product

Se dbarrasser de votre produit usag (Franais)

Cmo deshacerse del producto usado (Espaol)

Entsorgung Ihres Altgertes (Deutsch)

Wegwerpen van uw afgedankt apparaat (Nederlands)

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH

Windows Media and the Windows logo are

Deutsch -------------------------------- 150

DivX Ultra Certified products: DivX, DivX

Espaol -------------------------------- 102

Nederlands ---------------------------- 198

Manufactured under license from one or

Manufactured under license from Dolby

This product incorporates copyright protection

Optional Connections .................................................................................................... 18

Playing a MP3/ WMA disc ............................................................................................................................... 30

Playback other supported devices

Playback - Other Audio Player ..................................................................................... 34

Troubleshooting ........................................................................................................ 46-48

Turns on this unit or turns off to normal

k MP3 LINE-IN socket

Opens/closes the disc tray.

DISC/USB: toggles between DISC or

Adjusts the volume of the TV (for Philips

Remote Control (continued)

DISC: skips to the previous or next title/

t VOL +/ Adjusts the volume level.

v Numeric keypad 0-9

Remote Control (continued)

Using the remote control

A Open the battery compartment.

C Close the cover.

E Select the source you wish to control by

F Then select the desired function (for

Step 1: Placing the speakers

A Place the front left and right speakers at

B Place the centre speaker above the TV or

C Place the rear speakers at normal

D Place the subwoofer at the corner of the

Basic Connections (continued)

Option 1: Using the Scart socket

Basic Connections (continued)

Main Unit (rear)

A Connect the component video cables

B If your TV accepts progressive signals,

Basic Connections (continued)

Step 3: Connecting speakers

fix the claw

Main Unit (rear)

Step 4: Connecting the