FLIR Lepton Data Brief

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet
General Description
Lepton is a complete long-wave infrared (LWIR)
camera module designed to interface easily into
native mobile-device interfaces and other consumer
electronics. It captures infrared radiation input in its
nominal response wavelength band (from 8 to 14
microns) and outputs a uniform thermal image.
Features
Dimensions:
8.5 x 11.7 x 5.6 mm (without socket),
10.6 x 11.7 x 5.9 mm (including socket)
51-deg HFOV, 63.5-deg diagonal

(f/1.1 silicon doublet)
LWIR sensor, wavelength 8 to 14 m
80 (h) 60 (v) active pixels
Thermal sensitivity <50 mK
Integrated digital thermal image processing
functions, including automatic thermal
environment compensation, noise filters,
non-uniformity correction, and gain control
Optional temperature-stable output to
support radiometric processing
Export compliant frame rate (< 9 Hz)
MIPI and SPI video interfaces
Two-wire I2C-like serial-control interface
Uses standard cell-phone-compatible power
supplies: 2.8V to sensor, 1.2V to digital core,
and flexible IO from 2.5V to 3.1V
Fast time to image (< 0.5 sec)
Low operating power, nominally 150 mW

(< 160 mW over full temperature range)
Low power standby mode

RoHS compliant
32-pin socket interface to standard Molex or
similar side-contact connector
Applications
Mobile phones
Gesture recognition
Building automation
Thermal imaging
Night vision
Information on this page is subject to change without notice. Shipping: CIP per INCOTERMS 2010.
FLIR Proprietary-Confidential, and approved for distribution to authorized FLIR dealers only.
Version 1.2.3, October 15, 2014
Simplified Block Diagram

Integrated Camera Module
LWIR
sensor
CCI comm interface

Thermal image
processing engine
VoSPI
MIPI 1
2.8V, 1.2V, 2.5V to 3.1V IO
CLKin
1. Feature anticipated in a future product release
This documentation contains proprietary information to FLIR Systems,

Inc. This information must be maintained in confidence and used only in
a manner consistent with the documentation and any executed Non
Disclosure Agreement, and may not be disclosed to any third parties
without FLIR's written consent.
Note: All specifications subject to change without notice

Contents
1.0 Device Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.0 Key Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.0 Lepton Camera Module Pinout Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.0 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.0 System Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.0 Video Pipeline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.1 NUC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.2 Defect Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.3 Spatial / Temporal Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.4 AGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.5 Colorize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8.0 Operating States and Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8.1 Power States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8.2 FFC States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.3 Telemetry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8.4 Radiometry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.4.1 Radiometry Disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.4.2 Radiometry Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.5 AGC Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.0 Interface Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
9.1 Command and Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
9.2 VoSPI Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9.2.1 VoSPI Physical Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
9.2.2 VoSPI Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.3 MIPI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
10.0 Thermal Camera Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
11.0 Mounting Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
11.1 Socket Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
11.2 Mechanical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
11.3 Thermal Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
11.4 Optical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
12.0 Image Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
13.0 Spectral Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
14.0 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
14.1 DC and Logic Level Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
14.2 AC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
15.0 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
16.0 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
16.1 Compliance with Environmental Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
17.0 Abbreviations and Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Revision History
Revision
Date
Description of Change
1.0
5/1/2014
Initial release
1.1
7/7/2014
Updated to cover new features of the Lepton 2.0 release.
1.2
9/23/2014
Minor corrections
1.2.3
10/15/2014
Formatting and minor corrections
Contact Us
email: [email protected]
phone: 1-888-747-3547
http://www.FLIR.com
References
Lepton Software Interface Description Document (IDD) - Public. Document #110-0144-03.

1.0 Device Overview
Lepton is an infrared camera system that integrates a fixed-focus lens assembly, an 80x60 long-wave infrared
(LWIR) microbolometer sensor array, and signal-processing electronics. Easy to integrate and operate, Lepton
is intended for mobile devices as well as any other application requiring very small footprint, very low power,
and instant-on operation. Lepton can be operated in its default mode or configured into other modes through a
command and control interface (CCI).
Figure 1 shows a view of the Lepton camera, both as standalone and mounted in a socket.
Figure 1
Lepton Camera (with and without socket)

2.0 Applications
A typical application using the Lepton camera module is shown in Figure 2.
Figure 2
Typical Application
Camera Module
Camera Supply Inputs
Camera Shut Down

Camera Reset
Camera Clock Generation
MIPI
Video/ Control Interface
Camera Serial Interface ( CSI-2)
D-PHY Transmitter
VDD (2.8V)
VDDIO (2.5 V to 3.1V)
VDDC (1.2V)
PWR DWN L
RESET L
MASTER CLK
MIPI DATA P
MIPI DATA N
MIPI CLK P
MIPI CLK N
VDDIO (2.5 V to3.1V)
Camera Control Interface ( CCI)

Similar to I2C
Optional Video Interface
Video Over SPI
Optional Multiplexed Interface
Select
I2C , SPI,GPIO
SCL
SDA
SPI MOSI
SPI MISO
SPI CS L
SPI_ CLK
GPIO [3:0]
Note:
(1 ) The CCI pullup resistors are required and must be handled
outside the camera module by a host controller
.
(2 ) MIPI is not currently supported
.
.

3.0 Key Specifications
The key specifications of the Lepton camera module are listed in Table 1. See Figure 3 on page 8 for the
corresponding package pinout diagram.
Table 1 Key Specifications
Specification
Description
Overview
Function
Sensor technology
Spectral range
Array format
Pixel size
Effective frame rate
Thermal sensitivity
Temperature compensation
Non-uniformity corrections
FOV - horizontal
FOV - diagonal
Depth of field
Lens type
Output format
Solar protection
Electrical
Input clock
Video data interface
Control port
Input supply voltage (nominal)
Power dissipation
Mechanical
Package dimensions socket version
Weight
Environmental
Optimum operating temperature
range
Non-operating temperature range
Shock
Passive thermal imaging module for mobile equipment

Uncooled VOx microbolometer
Longwave infrared, 8 m to 14 m
80 60, progressive scan
17 m
8.6 Hz (exportable)
<50 mK (0.050 C)
Automatic. Output image independent of camera temperature
(optional mode - see Radiometry Modes, page 22).
Automatic (with scene motion)
51
63.5
10 cm to infinity
f/1.1 silicon doublet
User-selectable 14-bit, 8-bit (AGC applied)
Integral
25-MHz nominal, CMOS IO Voltage Levels
(see Operating States and Modes, page 13)
Video over SPI (see VoSPI Channel, page 28)
CCI (I2C-like), CMOS IO Voltage Levels
(see Command and Control Interface, page 27)
2.8 V, 1.2 V, 2.5 V to 3.1 V IO
(see DC and Logic Level Specifications, page 45)
Nominally 150 mW at room temperature (operating),
4 mW (standby)
8.5 11.7 5.6 mm (w l h)
0.55 grams (typ)
-10 C to +65 C
-40 C to +80 C
1500 G @ 0.4 ms

4.0 Lepton Camera Module Pinout Diagram
32 MIPI DATA P
31 MIPI DATA N
30 GND
29 MIPI CLK P
28 MIPI CLK N
27 GND
26 MASTER CLK
Pinout Diagram (viewed from back of camera module)
25 GND
Figure 3
24 RESET L
1 GND
23 PWR DWN L
2 GPIO3
22 SDA
3 GPIO2
21 SCL
4 GPIO1
20 GND
5 GPIO0
19 VDD
6 GND
18 GND
7 VDDC
8 GND
9 GND
10 GND
11 SPI MOSI
12 SPI MISO
13 SPI CLK
14 SPI CS L
15 GND
16 VDDIO
17 NC

5.0 Pin Descriptions
The Lepton camera module pin descriptions are shown in Table 2.
Table 2 Lepton Camera Module Pin Descriptions
Pin #
Pin Name
Signal
Type
Signal Level
Description
1, 6, 8,
9, 10,
15, 18,
20, 25,
27, 30
GND
Power
GND
Common Ground
GPIO3
IN/OUT
VDDIO
GPIO2
IN/OUT
VDDIO
The GPIOmultiplexed functions are optional

and configurable. The GPIO pins are unused
in the current release.
GPIO1
IN/OUT
VDDIO
GPIO0
IN/OUT
VDDIO
VDDC
Power
1.2V
Supply for MIPI Core, PLL, ASIC Core (1.2V

+/- 5%)
11
SPI_MOSI
IN
VDDIO
Video Over SPI Slave Data In (see VoSPI

Channel, page 28)
12
SPI_MISO
OUT
VDDIO
Video Over SPI Slave Data Out (see VoSPI

Channel, page 28)
13
SPI_CLK
IN
VDDIO
Video Over SPI Slave Clock (see VoSPI

Channel, page 28)
14
SPI_CS_L
IN
VDDIO
Video Over SPI Slave Chip Select, active low

(see VoSPI Channel, page 28)
16
VDDIO
Power
2.5 V 3.1 V
Supply used for System IO
17
No connection
19
VDD
Power
2.8V
Supply for Sensor (2.8V +/- 3%).
21
SCL
IN
VDDIO
Camera Control Interface Clock, I2C

compatible
22
SDA
IN/OUT
VDDIO
Camera Control Interface Data, I2C

compatible

Table 2 Lepton Camera Module Pin Descriptions (continued)
Pin #
Pin Name
Signal
Type
Signal Level
Description
23
PWR_DWN_L
IN
VDDIO
This active low signal shuts down the camera
24
RESET_L
IN
VDDIO
This active low signal resets the camera
26
MASTER_CLK
IN
VDDIO
ASIC Master Clock Input (see Operating

States and Modes, page 13)
28
MIPI_CLK_N
OUT
Diff Pair
MIPI Digital Video Clock Negative1
29
MIPI_CLK_P
OUT
Diff Pair
MIPI Digital Video Clock Positive1
31
MIPI_DATA_N
OUT
Diff Pair
MIPI Digital Video Data Negative1
32
MIPI_DATA_P
OUT
Diff Pair
MIPI Digital Video Data Positive1
Note(s)
1. MIPI is not currently supported. Let the MIPI pins float.
10

6.0 System Architecture
A simplified architectural diagram of the Lepton camera module is shown in Figure 4.
Figure 4
Lepton Architecture
Bias,
timing,
&
ctrl
Housing
Lens
Assy.
Focused
IR image
MIPI
VoSPI
OTP
Focalplane
array
(FPA)
SoC
I2C
( comm)
GPIO
(optional)
Discrete controls
Digital
data
stream
Image
Pipeline
Clk
VDD, VDDC, VDDIO
Thermistor
The lens assembly focuses infrared radiation from the scene onto an 80x60 array of thermal detectors with
17-micron pitch. Each detector element is a vanadium-oxide (VOx) microbolometer whose temperature
fluctuates in response to incident flux. The change in temperature causes a proportional change in each
microbolometers resistance. VOx provides a high temperature coefficient of resistance (TCR) and low 1/f
noise, resulting in excellent thermal sensitivity and stable uniformity. The microbolometer array is grown
monolithically on top of a readout integrated circuit (ROIC) to comprise the complete focal plane array (FPA).
Once per frame, the ROIC senses the resistance of each detector by applying a bias voltage and integrating
the resulting current for a finite period of time called the integration period.
The serial stream from the FPA is received by a system on a chip (SoC) device, which provides signal
processing and output formatting. The image pipeline is defined in Video Pipeline, page 12.
11

7.0 Video Pipeline
A block diagram of the video pipeline is shown in Figure 5.
Figure 5
Lepton Video Pipeline Block Diagram
Image Pipeline
raw data in
Non-uniformity
correction (NUC)
Defect
Replacement
Spatial / Temporal
Filtering
AGC disabled
AGC enabled
AGC
Colorize
AGC / Colorization enabled
The video pipeline includes non-uniformity correction (NUC), defect replacement, spatial and temporal
filtering, automatic gain correction (AGC), and colorization.
7.1
NUC
The non-uniformity correction (NUC) block applies correction terms to ensure that the camera produces a
uniform output for each pixel when imaging a uniform thermal scene. Factory-calibrated terms are applied to
compensate for temperature effects, pixel response variations, and lens-illumination roll-off. To compensate
for temporal drift, the NUC block also applies an offset term that can be periodically updated at runtime via a
process called flat-field correction (FFC). The FFC process is further described in FFC States, page 17.
7.2
Defect Replacement
The defect-replacement block substitutes for any pixels identified as defective during factory calibration or
during runtime. The replacement algorithm assesses the values of neighboring pixels and calculates an
optimum replacement value. The typical number of defective pixels is 1.
7.3
Spatial / Temporal Filtering
The image pipeline includes a number of sophisticated image filters designed to enhance signal-to-noise ratio
(SNR) by eliminating temporal noise and residual non-uniformity. The filtering suite includes a scene-based
non-uniformity correction (SBNUC) algorithm which relies on motion within the scene to isolate fixed pattern
noise (FPN) from image content.
7.4
AGC
The AGC algorithm for converting the full-resolution (14-bit) thermal image into a contrast-enhanced image
suitable for display is a histogram-based non-linear mapping function. See AGC Modes, page 25.
12

7.5
Colorize
The colorize block takes the contrast-enhanced thermal image as input and generates a 24-bit RGB color
output. This feature is anticipated in a future release and is not currently accessible.
8.0 Operating States and Modes

Lepton provides a number of operating states and modes, more completely defined in the sections that follow:
8.1
Power States, page 13

FFC States, page 17
Telemetry Modes, page 19
Radiometry Modes, page 22
AGC Modes, page 25
Interface Descriptions, page 27
Power States
Lepton currently provides five power states. As depicted in the state diagram shown in Figure 6, most of the
transitions among the power states are the result of explicit action from the host. The automatic transition to
and from the overtemp state is an exception. In the figure, transitions that require specific host-side action are
shown in bold. Automatic transitions are not bolded.
13

Figure 6
State Diagram Showing Transitions among the Five Power States
Note: Transition to off from every other

state occurs by removing VDD, VDDC, and
VDDIO. For simplicity, these transitions are
not shown below.
Apply VDD, VDDC, and
VDDIO
Off
Standby
10-sec counter
times out
Reset
Start-up
sequence
Uninitialized
Shutdown
sequence
Lepton > 80C
Overtemp
On
Start-up sequence
Lepton < 80C
14

The power states are listed here:
Off: When no voltage is applied, Lepton is in the off state. In the off state, no camera functions are
available.
Uninitialized: In the uninitialized state, all voltage forms are applied, but Lepton has not yet been
booted and is in an indeterminate state. It is not recommended to leave Lepton in this state as power is
not optimized; it should instead be booted to the on-state (and then transitioned back to standby if
imaging is not required).
On: In the on state, all functions and interfaces are fully available.
Standby: In the standby state, all voltage forms are applied, but power consumption is approximately 4
mW. In the standby state, no functions are available, but it is possible to transition to the on state via
the start-up sequence defined in Figure 7 on page 16. The shutdown sequence shown in Figure 7 on
page 16 is the recommended transition back to the standby state. It is also possible to transition
between standby and on states via software commands, as further defined in the software IDD.
Overtemp: The overtemp state is automatically entered when the Lepton senses that its temperature
has exceeded approximately 80 C. Upon entering the overtemp state, Lepton enables a shutdown
imminent status bit in the telemetry line and starts a 10-second counter. If the temperature of the
Lepton falls below 80 C before the counter times out, the shutdown imminent bit is cleared and the
system transitions back to the on state. If the counter does time out, Lepton automatically transitions to
the standby state.
15

Power sequencing is as shown in Figure 7.
Figure 7
Power Sequencing
Start-up Sequence
(from uninitialized to on
and standby to on)
Shutdown Sequence
(from on to standby)
De-assert
PWR_DWN_L
(should be high)
Assert PWR_DWN_L
Assert RESET_L
(should be low)
Enable MASTER_CLK
Wait > 100 msec
Wait > 5000 clk

periods
Disable MASTER_CLK
De-assert RESET_L
16

8.2
FFC States
Lepton is factory calibrated to produce an output image that is highly uniform, such as shown in Figure 8 (a),
when viewing a uniform-temperature scene. However, drift effects over long periods of time degrade
uniformity, resulting in imagery which appears more grainy (Figure 8 (b)) and/or blotchy (Figure 8 (c)).
Operation over a wide temperature range (for example, powering on at -10 C and heating to 65 C) will also
have a detrimental effect on image quality.
For scenarios in which there is ample scene movement, such as most handheld applications, Lepton is
capable of automatically compensating for drift effects using an internal algorithm called scene-based
non-uniformity correction (scene-based NUC or SBNUC). However, for use cases in which the scene is
essentially stationary, such as fixed-mount applications, scene-based NUC is less effective. In those
applications, it is recommended to periodically perform a flat-field correction (FFC). FFC is a process whereby
the NUC terms applied by the camera's signal processing engine are automatically recalibrated to produce the
most optimal image quality. The sensor is briefly exposed to a uniform thermal scene, and the camera updates
the NUC terms to ensure uniform output. The entire FFC process takes less than a second.
Figure 8
Examples of Good Uniformity, Graininess, and Blotchiness
(a) Highly uniform image
(b) Grainy image

(high-spatial frequency noise)
(c) Blotchy image

(low-spatial frequency noise)
The current FFC state is provided through the telemetry line. There are three FFC states, as illustrated in
Figure 9 on page 18:
1. FFC not commanded (default): In this state, Lepton applies by default a set of factory-generated
FFC terms.
2. FFC in progress: Lepton enters this state when FFC is commanded. The default FFC duration is
nominally 23 frames.
3. FFC complete: Lepton automatically enters this state whenever FFC is completed.
Lepton also provides an FFC desired flag in the telemetry line. The FFC desired flag is asserted at
start-up, when a specified period (default = 3 minutes) has elapsed since the last FFC, or when the
sensor temperature has changed by a specified value (default = 3 Celsius degrees) since the last FFC.
The FFC desired flag is intended to indicate to the host to command an FFC at the next possible
opportunity.
17

Figure 9
FFC States
Lepton powered on
FFC
Commanded
FFC Not
Commanded
FFC In
Progress
FFC Complete
FFC
Complete
FFC
Commanded
18

8.3
Telemetry Modes
There are three telemetry modes that affect the video output signal:
Telemetry disabled (default)
Telemetry as header
Telemetry as footer
Explicit commands over the CCI select each mode. The contents and encoding of the telemetry data are
shown in Table 3. Note that the second and third lines (line B and line C) are reserved for future growth and
contain no information at this time.
Table 3 Telemetry Data Content and Encoding
Telemetry
Row
Word
start
Word
End
Number
of 16-bit
Words
Name
Telemetry
Revision
Time Counter
Status Bits
12
Module serial #
13
16
Software revision
17
19
Reserved
20
21
Frame Counter
22
22
Frame Mean
23
23
FPA Temp
In counts (prior to conversion to Kelvin)
24
24
FPA Temp
In Kelvin x 100
25
25
Housing Temp
Notes
Format = major (byte 1), minor rev (byte

0).
32 bit counter in units of msec elapsed
since boot-up
See Table 4 on page 21
32-bit counter of output frames
In counts (prior to conversion to Kelvin)
19

Table 3 Telemetry Data Content and Encoding (continued)
Telemetry
Row
Word
start
Word
End
Number
of 16-bit
Words
Name
26
26
Housing Temp
27
28
Reserved
29
29
FPA Temp at last

FFC
Updated every FFC. Units are Kelvin x100
30
31
Time Counter at
last FFC
Updated every FFC. Units are msec
32
32
Housing temp at
last FFC
Updated every FFC. Units are Kelvin x100
33
33
Reserved
34
37
AGC ROI
38
38
AGC Clip-Limit
High
39
39
AGC Clip-Limit
Low
40
73
34
Reserved
74
74
Log2 of FFC
frames
75
79
Reserved
79
80
Reserved
78
79
Reserved
Notes
In Kelvin x 100
(top, left, bottom, right)
See AGC, page 12
See FFC States, page 17
20

Table 4 shows the encoding of the status bits (Telemetry Row A, Words 3 and 4).
Table 4 Status Bit Encoding (Telemetry Row A, words 3 and 4)
Bit start
Bit end
Number of
Bits
Name
Notes
Reserved
FFC Desired1
0 = FFC not desired

1 = FFC desired
FFC State1
Telemetry Revision 8:
00 = FFC never commanded
01 = FFC in progress
10 = FFC complete
11 = undefined
Telemetry Revision 9:
00 = FFC never commanded
01 = Reserved
10 = FFC in progress
11 = FFC complete
11
Reserved
12
12
AGC State
13
19
Reserved
20
20
Overtemp shut down

imminent
21
31
11
Reserved
0=Disabled
1=Enabled
Goes true 10 seconds before

shutdown (see Power States,
page 13)
Note(s)
1. See FFC States, page 17.
21

8.4
Radiometry Modes
There are two radiometry modes that affect the video output signal:
Radiometry disabled (default)

Radiometry enabled
The radiometric modes affect the transfer function between incident flux (scene temperature) and pixel output.
From an image-quality standpoint, both radiometry modes produce nearly identical performance (no change in
NEDT), and either mode is appropriate for strict imaging applications. However, for applications in which it is
intended to convert the Lepton output signal to one proportional to scene temperature, the radiometry-enabled
mode is preferred because the conversion is constant over the full operating temperature range of the
camera. Note that the following discussion assumes AGC is disabled (see AGC Modes, page 25). If AGC is
enabled, the differences between the two radiometry modes are completely obscured by the AGC algorithm.
In other words, with AGC enabled, any differences in signal output between radiometry-disabled and
radiometry-enabled modes are negligible.
8.4.1
Radiometry Disabled
With radiometry disabled, the output of a given pixel is intended to be near the middle of the 14-bit range
(~8192) when viewing a scene with a temperature equal to the temperature of the camera. Furthermore, the
responsivity, which is defined as the change in pixel output value for a change in scene temperature, varies
over the camera's operating temperature range. The resulting output for three different scene temperatures is
illustrated hypothetically in Figure 10 (note that the figure is for illustration purposes and not perfectly
representative).
22

Figure 10
Hypothetical Illustration of Camera Output vs. Camera Temperature in Radiometry-disabled Mode
23

8.4.2
Radiometry Enabled
With radiometry enabled, Lepton performs internal adjustments to the signal level such that in principle the
output is independent of the camera's own temperature. The resulting output for three different scene
temperatures is illustrated hypothetically in Figure 11. Notice in Figure 11 that the output is only a function of
scene temperature, not camera temperature (again, the figure is for illustration purposes only and not
perfectly representative. In practice, there is slight output variation as camera temperature changes,
particularly when the temperature change is rapid). Also notice that responsivity is also independent of
camera temperature; that is, the difference in output between two different scene temperatures is a constant,
as opposed to in Figure 10 on page 23, where it decreases with increasing camera temperature.
Figure 11
Hypothetical Illustration of Camera Output vs. Camera Temperature in Radiometry-enabled Mode
24

8.5
AGC Modes
There are two AGC modes:
AGC disabled (default)

AGC enabled
AGC is a process whereby the large dynamic range of the infrared sensor is collapsed to a range more
appropriate for a display system. For Lepton, this is a 14-bit to 8-bit conversion. In its most simplistic form,
AGC can be a linear mapping from 14-bit to 8-bit; however, a simple linear AGC is generally incapable of
providing pleasing imagery in all imaging conditions. For example, when a scene includes both cold and hot
regions (for example, a hot object in front of a cold background as illustrated in Figure 13 on page 26), linear
AGC can produce an output image in which most pixels are mapped to either full black or full white with very
little use of the grayshades (8-bit values) in between. Because of this limitation of linear AGC, a more
sophisticated algorithm is preferred.
Similar to most AGC algorithms that optimize the use of grayshades, Lepton's is histogram-based. Essentially
a histogram counts the number of pixels in each frame that have a given 14-bit value. Figure 12 on page 25
illustrates the concept for a 3x3 pixel area.
Figure 12
Illustration of a Histogram for a 3x3 Pixel Area
Classic histogram equalization uses the cumulative histogram as a mapping function between 14-bit and 8-bit.
The intent is to devote the most grayshades to those portions of the input range occupied by the most pixels.
For example, an image consisting of 60% sky devotes 60% of the available grayshades to the sky, leaving
only 40% for the remainder of the image. By comparison, linear AGC wastes grayshades when there are
gaps in the histogram, whereas classic histogram equalization allocates no grayshades to the gaps. This
behavior is in principle an efficient use of the available grayshades, but there are a few drawbacks:
The resulting contrast between an object and a much colder (or hotter) background can be rendered
poor by the fact the algorithm collapses the separation between such that the object is only 1
grayshade above the background. This phenomenon is illustrated in Figure 13.
25
Too much emphasis can be placed on background clutter, particularly when a mostly isothermal
background comprises a large fraction of the total image area. This is also illustrated in Figure 13.
The Lepton AGC algorithm is a modified version of classic histogram equalization that mitigates these
shortcomings. One such modification is a parameter called clip limit high. It clips the maximum population of
any single bin, limiting the influence of heavily populated bins on the mapping function. Another parameter
utilized by the Lepton algorithm is called clip limit low. It adds a constant value to every non-zero bin in the
histogram, resulting in additional contrast between portions of the histogram separated by gaps. Figure 13 is
an example showing the benefit of the Lepton clip parameters.
Figure 13
Comparison of Linear AGC and Classic/Lepton Variant of Histogram Equalization
(a) Linear AGC
(b) Classic Histogram Equalization
(c) Leptons Variant of Histogram

Equalization
A high value of clip limit high results in a mapping more like classic histogram equalization, whereas a low
value results in mapping more like linear AGC. For clip limit low, the opposite is true: a high value results in a
mapping more like linear AGC, whereas a low value results in a mapping more like classic histogram
equalization. The default values of both parameters produce a good compromise between the two; however,
because optimum AGC is highly subjective and often application dependent, customers are encouraged to
experiment to find settings most appropriate for the target application.
By default, the histogram used to generate Lepton's 14-bit to 8-bit mapping function is collected from the full
array. In some applications, it is desirable to have the AGC algorithm ignore a portion of the scene when
collecting the histogram. For example, in some applications it may be beneficial to optimize the display to a
region of interest (ROI) in the central portion of the image. When the AGC ROI is set to a subset of the full
image, any scene content located outside of the ROI is not included in the histogram and therefore does not
affect the mapping function (note: this does not mean the portion outside of the ROI is not displayed or that
AGC is not applied there, only that those portions outside the AGC ROI do not influence the mapping
function).
26

9.0 Interface Descriptions
9.1
Command and Control Interface
Lepton provides a command and control interface (CCI) via a two-wire interface similar to I2C (the only
difference relative to the true I2C standard is that all Lepton registers are 16 bits wide and consequently, only
16-bit transfers are allowed). The CCI address is 0x2A. The interface is described in detail in a separate
document, the Lepton Software Interface Description Document (IDD), FLIR document #110-0144-03.
Generally speaking, all commands issued through the CCI take the form of a get (reading data), a set
(writing data), or a run (executing a function). Table 5 shows a partial list of parameters / features
controllable through the CCI.
Table 5 Partial List of Parameters Controllable through the CCI
Power-On
Default
Parameter
Section in this document
Telemetry Line
Location
AGC Mode
Disabled
AGC Modes, page 25
A3-4
AGC ROI
(0,0,79,59)
AGC Modes, page 25
A34-A37
AGC Dampening Factor
64
AGC Modes, page 25
A42
AGC Clip Limit High
4800
AGC Modes, page 25
A38
AGC Clip Limit Low
512
AGC Modes, page 25
A39
SYS Telemetry Mode
Disabled
n/a
SYS Telemetry Location
Footer
n/a
SYS Number of Frames to

Average
FFC States, page 17
A74
VID Color LUT Select
Fusion
n/a
VID User Color LUT

Upload/Download
n/a
n/a
27

9.2
VoSPI Channel
The Lepton VoSPI protocol allows efficient and verifiable transfer of video over a SPI channel. The protocol is
packet-based with no embedded timing signals and no requirement for flow control. The host (master) initiates
all transactions and controls the clock speed. Data can be pulled from the Lepton (the slave) at a flexible rate.
This flexibility is depicted in Figure 14, which shows the use of a relatively slow clock utilizing most of the
available frame period as well as the use of a fast clock that bursts frame data. Once all data for a given frame
is read, the master has the option to stop the clock and/or deassert the chip select until the next available
frame. Alternatively, the master can simply leave the clock and chip select enabled, in which case Lepton
transmits discard packets until the next valid video data is available.
Figure 14
VoSPI Flexible Clock Rate
1/27 sec
1 frame video data

(a) FSCLK ~2.2 MHz
(a) FSCLK ~20 MHz
28

9.2.1
VoSPI Physical Interface
As illustrated in Figure 15, VoSPI utilizes 3 of the 4 lines of a typical SPI channel:
SCK (Serial Clock)

/CS (Chip Select, active low),
MISO (Master In/Slave Out).
Figure 15
VoSPI I/O
The MOSI (Master Out/Slave In) signal is not currently employed and should be grounded. Implementations
are restricted to a single master and single slave. The Lepton uses SPI Mode 3 (CPOL=1, CPHA=1); SCK is
HIGH when idle. Data is set up by the Lepton on the falling edge of SCK and should be sampled by the host
controller on the rising edge. See Figure 16. Data is transferred most-significant byte first and in big-endian
order. Figure 17 provides an example of the transmission of the value 0x8C08.
Figure 16
SPI Mode 3 (CPOL=1, CPHA=1)
Figure 17
SPI Bit Order (transmission of 0x8C08)
29

The maximum clock rate is 20 MHz. The minimum clock rate is a function of the number of bits of data per
frame that need to be retrieved. As described in the sections that follow, the number of bits of data varies
depending upon user settings (video format mode, telemetry mode). For default conditions (Raw14 mode,
telemetry disabled), there are 60 video packets per frame, each 1312 bits long, at approximately 25.9 frames
per second. Therefore, the minimum rate is on the order of 2 MHz.
9.2.2
VoSPI Protocol
VoSPI is built on a collection of object types as defined hierarchically below.
VoSPI Packet: The Lepton VoSPI protocol is based on a single standardized VoSPI packet, the
minimum transaction between master and slave. Each video packet contains data for a single video
line or telemetry line. In addition to video packets, the VoSPI protocol includes discard packets that are
provided when no video packets are available.
VoSPI Frame: A VoSPI frame is defined as a continuous sequence of VoSPI packets consisting of a
full frame's worth of pixel data.
VoSPI Stream: A VoSPI stream is defined as a continuous sequence of VoSPI frames.
As summarized in Table 6 on page 30, the number of packets per frame varies depending upon telemetry
mode.
Table 6 Packet Length and Number of Video Packets per Frame as a Function of User Settings
Video Format Mode
Raw14
Telemetry Mode
Telemetry Disabled
Telemetry Enabled
Video packets per frame: 60
Video packets per frame: 63
30

9.2.2.1VoSPI Packets
As depicted in Figure 18, each packet contains a 4-byte header followed by a 160-byte payload.
Figure 18
Generic VoSPI Packet

CRC
ID
Payload
4 bytes
160 bytes
For video packets, the header includes a 2-byte ID and a 2-byte CRC. The ID field is a 12-bit packet number
as shown in Figure 19 (the leading 4 bits of the ID field are reserved and are not part of the packet number).
Note that packet numbering restarts at zero on each new frame. The CRC portion of the packet header
contains a 16-bit cyclic redundancy check (CRC), computed using the following polynomial:
16
+x
12
+x +x
The CRC is calculated over the entire packet, including the ID and CRC fields. However, the four
most-significant bits of the ID and all sixteen bits of the CRC are set to zero for calculation of the CRC. There
is no requirement for the host to verify the CRC. However, if the host does find a CRC mismatch, it is
recommended to re-synchronize the VoSPI stream to prevent potential misalignment.
Figure 19
Video Packet
ID
CRC
xNNN
(16 bits)
CRC
(16 bits)
Payload
Video pixels for one video line
At the beginning of SPI video transmission until synchronization is achieved (see VoSPI Stream, page 33)
and also in the idle period between frames, Lepton transmits discard packets until it has a new frame from its
imaging pipeline. As shown in Figure 20, the 2-byte ID field for discard packets is always xFxx (where 'x'
signifies a don't care condition). Note that VoSPI-enabled cameras do not have vertical resolution
approaching 3840 lines (0xF00), and therefore it is never possible for the ID field in a discard packet to be
mistaken for a video line.
Figure 20
ID
xFxx
Discard Packet
CRC
Payload
xxxx
Discard data (same number of bytes as video packets)
31

The payload is 160 bytes long. Excluding telemetry lines1, each packet contains pixel data for all 80 pixels in a
single video line (with AGC disabled, the first two bits of each pixel's two-byte word are always set to 0; if AGC
is enabled, the first eight bits are set to 0).
This is illustrated in the following payload encoding figures.
Figure 21
Byte 0
Raw14 Mode: 1 video line per 160-byte payload

Byte 1
Byte 2
Byte 3
Line m
Line m
Pixel 0
Pixel 1
...
...
Byte 158
Byte 159
Line m
Pixel 79
9.2.2.2VoSPI Frames
A single Lepton frame contains data from all 60 rows of the sensor. However, the total number of video
packets is not necessarily 60; the exact number depends upon user settings, specifically the telemetry mode
(disabled, as header, or as footer). Table 7 shows the number of packets per frame and the contents of each
packet for all of the various combinations.
Table 7 Video Packet Contents Per Frame as a Function of Video Format and Telemetry-mode Settings
Configuration
Telemetry
Mode
As header
As footer
Disabled
Packet 0
Telemetry line A
FPA Row 0
FPA Row 0
Packet 1
Telemetry line B
FPA Row 1
FPA Row 1
Packet 2
Telemetry line C
FPA Row 2
FPA Row 2
Packet 3
FPA Row 0
FPA Row 3
FPA Row 3
Packet 29
FPA Row 26
FPA Row 29
FPA Row 29
Packet 30
FPA Row 27
FPA Row 30
FPA Row 30
Packet 31
FPA Row 28
FPA Row 31
FPA Row 31
Packet 32
FPA Row 29
FPA Row 32
FPA Row 32
Note(s)
1. See Telemetry Modes, page 19 for payload contents of the telemetry lines
32

Table 7 Video Packet Contents Per Frame as a Function of Video Format and Telemetry-mode Settings
Configuration
...
Packet 59
FPA Row 56
FPA Row 59
FPA Row 59
Packet 60
FPA Row 57
Telemetry line A
n/a
Packet 61
FPA Row 58
Telemetry line B
n/a
Packet 63
FPA Row 59
Telemetry line C
n/a
9.2.2.3VoSPI Stream
A VoSPI stream is simply a continuous sequence of VoSPI frames following a synchronization event. Provided
that synchronization is maintained, a VoSPI stream can continue indefinitely. Note that the frame rate of the
stream is nominally just below 27 Hz, allowing easy interface to a display system without the need for
host-side frame buffering. However, the rate of unique frames is just below 9 Hz to comply with US export
restrictions. For each unique frame, two duplicates follow in the VoSPI stream. This pattern is illustrated in
Figure 22, with unique frames shown in blue and duplicates shown in gray. In some applications, it might be
beneficial to identify the first of the three identical frames (the frame with the least latency). The 32-bit frame
counter provided in the telemetry lines (see Telemetry Modes, page 19) can be used for this purpose. It only
increments on new frames, which is also illustrated in Figure 22.
Figure 22
Frame Counter for Successive Frames
33

NOTE: Blue frames are different than the previous frames, gray frames are identical
to the previous blue frame.
9.2.2.3.1Establishing/Re-Establishing Sync
The basic process for establishing synchronization is listed below:
Deassert /CS and idle SCK for at least 5 frame periods (>185 msec). This step ensures a timeout of
the VoSPI interface, which puts the Lepton in the proper state to establish (or re-establish)
synchronization.
Assert /CS and enable SCLK. This action causes the Lepton to start transmission of a first packet.
Examine the ID field of the packet, identifying a discard packet. Read out the entire packet.
Continue reading packets. When a new frame is available (should be less than 39 msec after asserting
/CS and reading the first packet), the first video packet will be transmitted. The master and slave are
now synchronized.
9.2.2.3.2Maintaining Sync
There are three main violations that can result in a loss of synchronization:
Intra-packet timeout. Once a packet starts, it must be completely clocked out within 3 line periods.
Provided that VoSPI clock rate is appropriately selected and that /CS is not de-asserted (or SCLK
disrupted) in the midst of the packet transfer, an intra-packet timeout is an unexpected event.
Failing to read out all packets for a given frame before the next frame is available. Two examples of
this violation are shown in Figure 24 and Figure 25 on page 35. Note that the vertical blue line shown
in the illustrations represents an internal frame-sync signal that indicates a new frame is ready for
read-out.
Failing to read out all available frames. This violation is depicted in Figure 26 on page 35. Note that
the requirement to read out all frames applies to both the unique and the duplicate frames.
A CRC error does not result in an automatic loss of synchronization. However, as mentioned previously, it is
recommended to intentionally re-synchronize (de-assert /CS for >185 msec) following a CRC error.
The following figures are examples of violations that result in a loss of synchronization.
34

Figure 23
Valid Frame Timing (no loss of synchronization)
Figure 24
Clock Too Slow - Failure to Read an Entire Frame Within the Frame Period
Figure 25
Intra-frame Delay Too Long - Failure to Read Out an Entire Frame Before the Next is Available
Figure 26
Failure to Read Out an Available Frame
9.3
MIPI Interface
An optional MIPI interface will be supplied in a later release of Lepton.
35

10.0 Thermal Camera Basics
It is noteworthy that the integration period for a thermal detector does not have the same impact on image
formation as it does for a photon detector, such as a typical CMOS array. A photon detector converts incoming
photons to electrons with near-instantaneous response time but only collects information from the scene
during the integration period. In other words, high-speed phenomena (such as a strobed signal) can be
missed entirely if the resulting photons are incident at a point in time when the detector is not integrating. A
thermal detector, on the other hand, is always changing temperature in response to incident radiation. That is
to say, it is always active regardless of whether or not it is being actively integrated. The integration period
only refers to the time that resistance is being sensed by integration of current, not the time the sensor is
actively responding to irradiance from the scene. The ability to detect high-speed phenomena is more a
function of the detector's thermal time constant, which governs the rate of temperature change. For Lepton,
the detector time constant is on the order of 12 msec, which means that an instantaneous irradiance change
will result in a temperature change of the detector as shown in Figure 27.
Figure 27
Illustration of Lepton Detector Time Constant
In addition to integrating signal current, the ROIC also digitizes and multiplexes the signal from each detector
into a serial stream. And the Lepton ROIC digitizes data from an on-chip temperature sensor as well as a
thermistor attached to the camera housing. An anti-reflection (AR) coated window is bonded above the sensor
array via a wafer-level packaging (WLP) process, encapsulating the array in a vacuum. The purpose of the
vacuum is to provide high thermal resistance between the microbolometer elements and the ROIC substrate,
allowing for maximum temperature change in response to incident radiation.
36

11.0 Mounting Specifications
The Lepton camera mounting dimensions are shown in Figure 28.
Figure 28
Lepton Camera Mounting Dimensions
37

11.1 Socket Information
The Lepton module is compatible with two commercially-available sockets, Molex 1052028-1001 and Molex
105028-2011, illustrated in Figure 29 below. The former makes electrical contact on the upper surface of a
printed circuit board, the latter to the lower surface (with a cutout in the board that allows the socket to pass
through). Figure 30 depicts both socket configurations mounted on a PCB.
Figure 29
Two Commercially-available Sockets (both from Molex) Compatible with Lepton
105028-2011
105028-1001
38

Figure 30
Both Sockets Mounted on a PCB
39

11.2 Mechanical Considerations
The socket is not intended to retain the Lepton assembly under high-shock conditions. It is recommended to
incorporate front-side retention such as illustrated in Figure 31.
Figure 31
Recommended Approach to Retaining Lepton in the end Application
The Lepton camera is not a sealed assembly. Consequently, for most applications it is recommended to locate
the assembly behind a sealed protective window. Common materials for LWIR windows include silicon,
germanium, and zinc selenide (LWIR absorption in silicon is on the order of 15%/mm, which means NEDT is
adversely affected using a silicon window. Bulk absorption in germanium and zinc selenide is negligible, and
performance is essentially unchanged provided both surfaces of the window are anti-reflection (AR) coated.)
Note that the window should be sized large enough to avoid encroaching upon the optical keepout zone (see
Optical Considerations, page 41).
11.3 Thermal Considerations

It is important to minimize any temperature gradient across the camera. The sensor should be mounted in
such a fashion so as to isolate it from heat loads such as electronics, heaters, and non-symmetric external
heating.
The surrounding area must be able to support and withstand the dissipation of up to 160 mW of heat by the
camera.
40

11.4 Optical Considerations
The optical keepout zone is shown in Figure 32. To avoid mechanical vignetting, do not impinge upon the
keepout zone
Figure 32
Optical Keepout Zone

d = 1.96 mm + 1.39(z)
Lens flange
41

12.0 Image Characteristics
The information given in Table 8 applies across the full operating temperature range.
Table 8 Image Characteristics
Parameter
Description
Value
NETD
Noise Equivalent Temperature

Difference (random temporal
noise)
<50 mK
Intrascene Range
Minimum and maximum

scene temperature
0 K to >400 K
Operability
Number of non-defective
pixels
>99.0%
Number of adjacent defective

pixels
Unallowed1
Clusters
(20 mK typical)
(<1 defect typical)
Adjacent means any of the 8

nearest neighbors (or nearest
5 for an edge pixel, nearest 3
for a corner).
Note(s)
1. : Only single-pixel defects are allowed (no clusters)
The nominal curve of on-axis modulation transfer function (MTF) for the Lepton lens assembly is shown for
reference in Figure 33.
42

Figure 33
Nominal Curve of On-axis Modulation Transfer Function (MTF)
43

13.0 Spectral Response
For reference, Figure 34 depicts the spectral response of the Lepton camera
Figure 34
Normalized Response as a Function of Signal Wavelength
44

14.0 Electrical Specifications
14.1 DC and Logic Level Specifications
Table 9 DC and Logic Levels
Symbol
Parameter
Min
Typ
Max
Units
VDDC
Core Voltage (primary power for the

Lepton internal ASIC)
1.14
1.20
1.26
Volts
VDD
Sensor Voltage (primary power for

the Lepton internal sensor chip)
2.72
2.80
2.88
Volts
VDDIO
I/O Voltage (primary power for the

Lepton I/O ring)
2.5
3.1
Volts
I_DDC
Supply current for core (VDDC)
76
84
110
mA
I_DD
Supply current for sensor (VDD)
12
14
161
mA
I_DDIO
Supply current for I/O ring (VDDIO)
mA
Note(s)
1. Maximum at 65 degrees C
14.2 AC Electrical Characteristics

Table 10 AC Electrical Characteristics
Parameter
Min
Typ
Max
Units
MASTER_CLK, Fclk
TBD
25 MHz
TBD
Master clock
rate
MASTER_CLK, Fclk duty
45%
50%
55%
Master clock
duty cycle
MASTER_CLK, tr
--
--
TBD
Clock rise time

(10% to 90%)
MASTER_CLK, tf
--
--
TBD
Clock fall time

(90% to 10%)
SPI_CLK, Fclk
See note1
SPI_CLK, Fclk duty
45%
50%
20 MHz
VoSPI clock rate
55%
SPI-clock duty
cycle
45

Table 10 AC Electrical Characteristics (continued)
Parameter
Min
Typ
Max
Units
SPI_CLK, tr
--
--
TBD
SPI clock rise

time (10% to 90%)
SPI_CLK, tf
--
--
TBD
SPI clock fall

time (90% to 10%)
1 MHz
I2C clock rate
SCL, Fclk
SCL, Fclk duty
45%
50%
55%
I2C-clock duty
cycle
SCL_CLK, tr
--
--
TBD
I2C clock rise

time (10% to 90%)
SCL_CLK, tf
--
--
TBD
I2C clock fall

time (90% to 10%)
Note(s)
1. As described in VoSPI Protocol, page 30, the minimum VoSPI clock frequency is dependent upon the
requirement to read out all video packets for a given frame within the frame period. The size and number of
video packets vary with user settings.
15.0 Absolute Maximum Ratings

Electrical stresses beyond those listed in Table 11 may cause permanent damage to the device. These are
stress rating only, and functional operation of the device at these or any other conditions beyond those
indicated under the recommended operating conditions listed in Table 9 on page 45 is not implied. Exposure
to absolute-maximum-rated conditions for extended periods of time may affect device reliability.
Table 11 Absolute Maximum Ratings
Parameter
Absolute Maximum Rating
Core Voltage (VDDC)
1.5 V
Sensor Voltage (VDD)
4.8 V
I/O Voltage (VDDIO)
4.8 V
Voltage on any I/O pin
4.8 V
46

16.0 Environmental Specifications
Environmental stresses beyond those listed may cause permanent damage to the device. Exposure to
absolute-maximum-rated conditions for extended periods of time may affect device reliability.
Table 12 Environmental Specifications
Stress
Maximum Rating
Operating Temperature Range
-10 C to 65 C
(-20 C to 75 C with some possible performance degradation)
Maximum Operating Temperature
80 C1
Storage Temperature
-40 C to 80 C
Altitude (pressure)
12 km altitude equivalent
Relative Humidity
95%
Thermal Shock
Air-to-air across operating temp. extremes (-10 C to 65 C,

65 C to -10 C)
Mechanical Shock
1500 g, 0.4 msec
Vibration
Transportation profile, 4.3 grms
ESD
Human Body Model (HBM), 2kV

Charged Device Model (CDM), 500V
Note(s)
1. Lepton contains an automatic shutdown feature when its internal temperature exceeds the maximum safe
operating value. See Power States, page 13.
16.1 Compliance with Environmental Directives

Lepton complies with the following directives and regulations:
Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances in electrical and
electronic equipment (RoHS)
Directive 2002/96/ EC, Waste Electrical and Electronic Equipment (WEEE).
Regulation (EC) 1907/2006, Registration, Evaluation, Authorization and Restriction of Chemicals
(REACH)
47

17.0 Abbreviations and Acronyms
Abbreviation
Description
AGC
Automatic Gain Control
AR
Anti-reflection
CCI
Command and Control Interface
CRC
Cyclic Redundancy Check
DSP
Digital Signal Processor
EMC
Electromagnetic Compatibility
FFC
Flat Field Correction
FOV
Field of View
FPA
Focal Plane Array
FPN
Fixed Pattern Noise
GPIO
General Purpose IO
HFOV
Horizontal Field of View
I2C
Inter-Integrated Circuit
IDD
Interface Description Document
LWIR
Long Wave Infrared
MIPI
Mobile Industry Processor Interface
MISO
Maser In/Slave Out
MOSI
Master Out/Slave In
NEDT
Noise Equivalent Differential Temperature
NUC
Non-Uniformity Correction
OTP
One-Time Programmable
PLL
Phase-Lock Loop
REACH
Registration, Evaluation, Authorization, and Restriction of Chemicals
RoHS
Reduction of Hazardous Substances

48

ROIC
Readout Integrated Circuit
SBNUC
Scene-based Non-uniformity Correction
SNR
Signal to Noise Ratio
SoC
System on a Chip
SPI
Serial Peripheral Interface
SVP
Software-based Video Processing
TCR
Temperature Coefficient of Resistance
TWI
Two-wire Interface
VoSPI
Video Over SPI
VOx
Vanadium-oxide
WEEE
Waste Electrical and Electronic Equipment
WLP
Wafer-level Packaging
49

FLIR Commercial Systems, 2014. All rights reserved worldwide. No parts of this manual, in whole or in part, may be
copied, photocopied, translated, or transmitted to any electronic medium or machine readable form without the prior
written permission of FLIR Commercial Systems
Names and m a r k s appearing on the p r o d u c t s herein are either registered trademarks or trademarks of FLIR
Commercial Systems and/or its subsidiaries. All other trademarks, trade names, or company names referenced
herein are used for identification only and a r e the property of their respective owners.
Liberation fonts are copyright 2009 by RedHat and a r e used under authority of the G N U public license. Information
about these fonts and t h e G N U public license can b e found a t : https://www.redhat.com/promo/fonts/.
This product is protected by patents, design patents, patents pending, or design patents pending.
If you have q u e s t i o n s that are not covered in this m a n u a l , or need service, contact FLIR Commercial Systems Customer
Support at 805.964.9797 for additional information prior t o returning a camera.
This documentation and the requirements specified herein are subject to change without notice.
This equipment must be disposed of as electronic waste.

Contact your nearest FLIR Commercial Systems, Inc. representative for instructions on how to return the
p r o d u c t to FLIR for proper disposal.
FCC Notice. This device is a subassembly designed for incorporation into other products in order to provide an infrared camera function.
It is not an end-product fit fo1r consumer use. When incorporated into a host device, the end-product will generate, use, and radiate radio
frequency energy that may cause radio interference. As such, the end-product incorporating this subassembly must be tested and
approved under the rules of the Federal Communications Commission (FCC) before the end-product may be offered for sale or lease,
advertised, imported, sold, or leased in the United States. The FCC regulations are designed to provide reasonable protection against
interference to radio communications. See 47 C.F.R. 2.803 and 15.1 et seq.
Industry Canada Notice. This device is a subassembly designed for incorporation into other products in order to provide an infrared
camera function. It is not an end-product fit for consumer use. When incorporated into a host device, the end-product will generate, use,
and radiate radio frequency energy that may cause radio interference. As such, the end-product incorporating this subassembly must be
tested for compliance with the Interference-Causing Equipment Standard, Digital Apparatus, ICES-003, of Industry Canada before the
product incorporating this device may be: manufactured or offered for sale or lease, imported, distributed, sold, or leased in Canada.
Avis dIndustrie Canada. Cet appareil est un sous-ensemble conu pour tre intgr un autre produit afin de fournir une fonction de
camra infrarouge. Ce nest pas un produit final destin aux consommateurs. Une fois intgr un dispositif hte, le produit final va
gnrer, utiliser et mettre de lnergie radiofrquence qui pourrait provoquer de linterfrence radio. En tant que tel, le produit final
intgrant ce sous-ensemble doit tre test pour en vrifier la conformit avec la Norme sur le matriel brouilleur pour les appareils
numriques (NMB-003) dIndustrie Canada avant que le produit intgrant ce dispositif puisse tre fabriqu, mis en vente ou en location,
import, distribu, vendu ou lou au Canada.
EU Notice. This device is a subassembly or component intended only for product evaluation, development or incorporation into other
products in order to provide an infrared camera function. It is not a finished end-product fit for general consumer use. Persons handling
this device must have appropriate electronics training and observe good engineering practice standards. As such, this product does not
fall within the scope of the European Union (EU) directives regarding electromagnetic compatibility (EMC). Any end-product intended for
general consumer use that incorporates this device must be tested in accordance and comply with all applicable EU EMC and other
relevant directives.
50

FLIR Lepton Data Brief

Uploaded by

Copyright:

Available Formats

FLIR Lepton Data Brief

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FLIR Lepton Data Brief

Uploaded by

Copyright:

Available Formats

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

51-deg HFOV, 63.5-deg diagonal

Low operating power, nominally 150 mW

Low power standby mode

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Simplified Block Diagram

CCI comm interface

1. Feature anticipated in a future product release

This documentation contains proprietary information to FLIR Systems,

Note: All specifications subject to change without notice

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Updated to cover new features of the Lepton 2.0 release.

Formatting and minor corrections

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Lepton Camera (with and without socket)

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Camera Shut Down

Camera Control Interface ( CCI)

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Passive thermal imaging module for mobile equipment

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Pinout Diagram (viewed from back of camera module)

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

The GPIOmultiplexed functions are optional

Supply for MIPI Core, PLL, ASIC Core (1.2V

Video Over SPI Slave Data In (see VoSPI

Video Over SPI Slave Data Out (see VoSPI

Video Over SPI Slave Clock (see VoSPI

Video Over SPI Slave Chip Select, active low

Supply used for System IO

Supply for Sensor (2.8V +/- 3%).

Camera Control Interface Clock, I2C

Camera Control Interface Data, I2C

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

This active low signal shuts down the camera

This active low signal resets the camera

ASIC Master Clock Input (see Operating

MIPI Digital Video Clock Negative1

MIPI Digital Video Clock Positive1

MIPI Digital Video Data Negative1

MIPI Digital Video Data Positive1

1. MIPI is not currently supported. Let the MIPI pins float.

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Version 1.2.3, October 15, 2014

FLIR LEPTON Long Wave Infrared (LWIR) Datasheet

Lepton Video Pipeline Block Diagram

AGC / Colorization enabled

Spatial / Temporal Filtering

Version 1.2.3, October 15, 2014