Scribd
Upload
568 views2 pages

Model 601 Operating Principles

The Model 601 above-ground insulation checker uses radio frequency signals instead of direct current to locate electrical shorts between insulated pipe sections. It circumvents issues with direct current measurements by using the skin effect phenomenon where radio signals travel only on the surface of conductive pipes. This gives pipes a relatively high resistance to radio signals compared to direct current. The instrument detects the magnitude of radio frequency voltage between probes, indicating the resistance of the material between the probes and locating points of low resistance such as faulty insulators or metallic shorts.

Uploaded by

Profumo San Martin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
568 views2 pages

Model 601 Operating Principles

The Model 601 above-ground insulation checker uses radio frequency signals instead of direct current to locate electrical shorts between insulated pipe sections. It circumvents issues with direct current measurements by using the skin effect phenomenon where radio signals travel only on the surface of conductive pipes. This gives pipes a relatively high resistance to radio signals compared to direct current. The instrument detects the magnitude of radio frequency voltage between probes, indicating the resistance of the material between the probes and locating points of low resistance such as faulty insulators or metallic shorts.

Uploaded by

Profumo San Martin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1 of 2

Model 601 Above-Ground Insulation Checker


Principles of Operation

The Model 601 above-ground insulation checker is an instrument for


locating electrical shorts occurring between adjacent (normally insulated)
pipe sections in a (potentially) complex pipe network.
The DC resistance of metallic pipe is so small that it is virtually impossible
with conventional DC measuring systems to accurately determine where
adjacent pipes are shorted together. The issue can be particularly difficult
when other pipes are (electrically) interconnected with the pipe under study,
since additional short circuits can be present that are indistinguishable, by
conventional DC measuring devices, from a short circuit at the insulator of
interest.
The Model 601 insulation checker circumvents this issue by applying a radio
frequency signal across the insulator of interest, rather than a DC source of
energy. Radio frequency electromagnetic signals do not travel through a pipe
(conductor) in a uniform fashion (as would a DC current) but, rather, they
ride completely on the surface of the pipe which leads to a relatively high
AC Resistance for the pipe, in contrast to a low DC Resistance. This
phenomenon is known as the skin effect.
The Model 601 unit utilizes this phenomenon by applying a radio frequency
signal across normally insulated adjacent portions of a pipe via two probes.
Since the effective AC Resistance of the pipe system will be large (due to
the skin effect), any electrical shorts that may be present around the pipe
system, that would impact a DC measurement, will have little effect on the
Model 601 measurements (the pipe system will appear as an open circuit
to the AC source, compared to appearing as a short circuit to a DC source).
Consequently, only the effective AC Resistance of the material (normally an
insulator) appearing directly between the probes will be a factor with regard
to the output of the Model 601 insulation checker. Thus, the Model 601 unit
can distinguish between insulation shorts and shorts associated with
interconnected piping.

Page 2 of 2

As mentioned above, it is the effective AC Resistance of the material


appearing between the probes that affects the output of the Model 601 unit.
In the case of a perfect insulator (non-conductor), the AC Resistance will be
high and, in the case of a leaky insulator, the AC Resistance will be
relatively low. The Model 601 unit assesses the AC Resistance level by
detecting the magnitude of the RF voltage appearing between the probes. A
large value for the RF voltage will suggest a large AC Resistance value and
a small RF voltage value will indicate a relatively-small AC Resistance.
The RF voltage appearing across the probes is determined by a built-in
detector circuit that is tuned to the same frequency as that of the RF
oscillator and the RF voltage is rectified internally to produce a DC voltage.
It is this DC voltage that dictates the needle position on the meter scale.
Consequently, the needles location on the meter will reflect the level of AC
Resistance for the material appearing between the probes. For a perfect
insulator, the needle will be fully to the right on the scale (reflecting a large
value of AC Resistance) and the needle will move to the left hand side of the
scale when lower AC Resistances are detected. Again, lower AC
Resistances would indicate the presence of non-perfect (leaky) insulators
(ionically-conducting materials) or metallic shorts.
Because of the skin-effect discussed above, it is possible to locate a shorted
bolt in a normally insulating flange using the Model 601 unit, even though
the bolt being examined may or may not be the only shorted bolt in the
flange.
Note: The Model 601insulation checker cannot be used to check the
condition of a buried flange from remote test leads. However, the Model
702 insulation checker can be used to check the quality of insulation in
buried flanges and carrier pipe/casing systems.

You might also like