Flanges Pipe Systems

Marine & Offshore
BONDSTRAND 2000M & 7000M

Glassfibre Reinforced Epoxy (GRE)
Flanges & Pipe Systems
1 to 6 inch (Quick-lock joint), 8 to 40 inch
(Taper/Taper joint) with external pressure requirements
Pipex px are the sole

distributor for NOV FGS in
the UK and Ireland
T: +44 (0) 1752 581200

F: +44 (0) 1752 581209
[email protected]
www.pipexpx.com
Bondstrand 2000M/7000M for marine
1 to 6 inch (Quick-lock joint), 8 to 40 inch (Taper/Taper joint) with external pressure requirements
Uses and applications
Ballast
Chlorination
Draining
Cargo line
Sanitary service & sewage
Portable discharge line

Stripping lines
Tank cleaning (salt water)
Fire protection mains
Various other applications
A complete library of Bondstrand pipe and fittings in PDS and PDMS-format is available on CD-ROM. Please contact NOV Fiber
Glass Systems for details.
For specific fire protection requirements, an outer layer of passive fire protection is available.
For pipe systems without external pressure requirements, please contact your Bondstrand representative.
Approvals
In 1993, IMO (International Maritime Organisation) issued a resolution (A.18/Res. 753) covering acceptance criteria for assuring
ship safety. Major certifying bodies have adopted and implemented these Guidelines in their respective Rules and Regulations
for the Classification of Ships.
All Bondstrand pipe series used in the marine industry are designed and type-approved by the below major certifying bodies. (A
complete list is available, on request)
American Bureau of Shipping (ABS), U.S.A.;
Bureau Veritas, France;
Det Norske Veritas, Norway;
Germanischer Lloyd, Germany;
Lloyds Register, United Kingdom;
Nippon Kaiji Kyokai, Japan;
Registro Italiano Navale (RINA), Italy;
United States Coast Guard (USCG), U.S.A.
Characteristics
Maximum operating temperature: up to 93C. Higher temperature application is available, please consult NOV Fiber Glass Systems.
Pipe diameter: 1 - 40 inch (25-1000 mm).
Pipe system design for pressure ratings up to: 25 bar (362 psi) for 1 - 4 inch and 17.2 bar (250 psi) for 5 - 40 inch, depending type
of fittings, see contents for each fitting designated pressure rating.
ASTM D-2992 Hydrostatic Design Basis (Procedure B - service factor 0.5);
ASTM D-1599 Safety factor of 4:1. Design criteria for external pressure requirements are in accordance with IMO regulations.
Bondstrand 2000M
ASTM D-2310 Classification: RTRP-11FW or RTRP-11FX for static hydrostatic design basis. Complies with ASTM F-1173 Classification
and ASTM D-2996 designation.
Bondstrand 7000M
ASTM D-2310 Classification: RTRP-11AW or RTRP-11AX for static hydrostatic design basis. Complies with ASTM F-1173 Classification
and ASTM D-2996 designation.
Joining Systems
Quick-Lock joint
1-4 inch
Taper/Taper joint
6-40 inch
Quick-Lock adhesive-bonded joint
Taper/Taper adhesive-bonded joint
Table of contents
Pipe series .............................................................................................................
Joining system and configuration .........................................................................
Typical Pipe length ................................................................................................
Typical Pipe dimensions and weights ...................................................................
Ultimate Collapse Pressures .............................................................................
Joint dimensions Quick-Lock .............................................................................
Joint dimensions Taper/Taper................................................................................
Span length .......................................................................................................
Elbows ............................................................................................................... 9-10

Tees (Equal, Reducing).................................................................................. 11-17
Bushing Saddles ..................................................................................................
18
Laterals ..................................................................................................................
18
Reducers (Concentric, Eccentric)......................................................................... 19-20
Couplings ..............................................................................................................
21
Nipples ..................................................................................................................
21
Support Saddles ...................................................................................................
22
Grounding Saddles ...............................................................................................
23
Bell Mouths..................................................................................................
23
Assembly of double O-ring expansion joint ..........................................................
24
Expansion coupling ...............................................................................................
24
Adapters ................................................................................................................
25
Adhesive ............................................................................................................
26
Engineering design & installation data .................................................................
28
Specials .................................................................................................................
28
Field testing ...........................................................................................................
28
Conversions ..........................................................................................................
28
Important notice.....................................................................................................
28
Pipe series
Pipe
Filament-wound Glassfiber Reinforced Epoxy (GRE) pipe for Bondstrand adhesive-bonding
systems.
Fittings
A wide range of lined filament-wound Glassfiber Reinforced Epoxy (GRE) fittings for
Bondstrand adhesive-bonding systems. For special fittings, not listed in this product guide,
please contact your NOV FGS representative.
Flanges
Filament-wound Glassfiber Reinforced Epoxy (GRE) heavy-duty flanges and stub-end ring
flanges for Quick-Lock adhesive bonding systems. Standard flange drilling patterns as per
ANSI B16.5 (150 Lb). Other flange drilling patterns, such as ANSI B16.5 (> 150 Lb), DIN,
ISO and JIS are also available. Please refer to Bondstrand series 2000M/ 7000M Flanges
brochure.
Bondstrand 2000M
Glassfiber Reinforced Epoxy (GRE) pipe system. Standard 0.5 mm internal resin-rich
reinforced liner. Maximum operating temperature: 93C (for higher temperature rating,
consult NOV Fiber Glass Systems).
Maximum pressure rating: 25 bar (362 psi) for 1 - 4 inch, 17.2 bar (250 psi) for 6 - 40 inch.
Minimum pressure: full vacuum. External Pressure Requirements: In accordance with IMO
Regulations.
Bondstrand 7000M (* conductive)
Glassfiber Reinforced Epoxy (GRE) pipe system. Maximum operating temperature: 93C
(for higher temperature rating, consult NOV Fiber Glass Systems).
Maximum pressure rating: 25 bar (362 psi) for 1 - 4 inch, 17.2 bar (250 psi) for 6 - 40 inch.
Minimum pressure: full vacuum.
External Pressure Requirements: In accordance with IMO Regulations.
* Conductive
Our conductive pipe systems have been developed to prevent accumulation of potentially
dangerous levels of static electrical charges. Pipe, fittings and flanges contain high strength
conductive filaments. Together with a conductive adhesive this provides an electrically
continuous system.
Description Bondstrand 2000M
Bondstrand 7000M
Pipe diameter
1-40 inch
1-40 inch
Joining system
Quick-Lock 1-6 inch
Quick-Lock 1-6 inch

Taper/Taper 8-40 inch
Taper/Taper 8-40 inch
Liner
*0.5 mm
**Temperature 93C
93C
Pressure Rating^
17.2 bar (5-40 inch)
17.2 bar (5-40 inch)

25 bar (1-4 inch)
25 bar (1-4 inch)
* Also available without liner;
** For temperature above 93C, please consult NOV Fiber Glass Systems;
^ See fitting table for specific pressure rating for individual fitting.
Joining system &

configuration
Pipe
25-150 mm (1-6 inch):
Quick-Lock (straight/taper) adhesive joint with integral pipe stop in bell end.
End configuration: Integral Quick-Lock bell end x shaved straight spigot.
200-1000 mm (8-40 inch):
Taper/Taper adhesive joint.
End configuration: Integral Taper bell x shaved taper spigot
Fitting and Flanges
25-150 mm (1-6 inch):
Quick-Lock (straight/ taper) adhesive joint with integral pipe stop in bell end.
End configuration: Integral Quick-Lock bell ends.
200-1000 mm (8-40 inch):
Taper/Taper adhesive joint.
End configuration: Integral Taper bell ends.
Note: * Pipe nipples, saddles and flanged fittings have different end configurations.
Typical pipe length
Nominal
Joining
Pipe Size
System
(mm)
(inch)
25-40
1-1.5
Quick-Lock
50-125
2-5
Quick-Lock
150
6
Quick-Lock
200-250
8-10
Taper/Taper
300-400
12-16
Taper/Taper
450-1000
18-40
Taper/Taper
* Tolerance +/- 50 mm
Approximate overall Length

Europe Plant
Asia Plant
(m)
(m)
5.5
3.0
6.15
5.85/9.0
6.1
5.85/9.0
6.1/11.8
5.85/11.89
6.05/11.8
5.85/11.89
11.8
11.89
Typical pipe dimensions

and weight
Bondstrand 2000M
Nominal
Pipe Size

[mm]
[inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
550
22
600
24
650
26
700
28
750
30
800
32
900
36
1000
40
Pipe
Inside
Diameter
[mm]
27.1
42.1
53.0
81.8
105.2
131.9
159.0
208.8
262.9
313.7
337.6
385.8
433.8
482.1
530.3
578.6
650.0
700.0
750.0
800.0
900.0
1000.0
Bondstrand 7000M
Nominal
Pipe Size

[mm]
[inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
550
22
600
24
650
26
700
28
750
30
800
32
900
36
1000
40
Pipe
Inside
Diameter
[mm]
27.1
42.1
53.0
81.8
105.2
131.9
159.0
208.8
262.9
313.7
337.6
385.8
433.8
482.1
530.3
578.6
650.0
700.0
750.0
800.0
900.0
1000.0
Minimum
Struct. Wall
Thickness [t]
[mm]
3.0
3.0
3.1
3.1
4.1
4.1
4.1
5.5
7.0
8.3
9.0
10.3
11.5
12.8
14.1
15.4
17.3
18.7
20.0
21.4
24.0
26.9
Average
Pipe
Weight
[kg/m]
0.7
1.3
1.3
1.8
3.1
3.5
4.6
7.4
12
17
19
25
32
39
49
56
66
75
93
102
132
165
Minimum
Struct. Wall
Thickness [t]
[mm]
3.5
3.5
3.6
3.6
4.6
4.6
4.6
5.5
7.0
8.3
9.0
10.3
11.5
12.8
14.1
15.4
17.3
18.7
20.0
21.4
24.0
26.9
Average
Pipe
Weight
[kg/m]
0.7
1.3
1.3
1.8
3.1
3.5
4.6
7.4
12
17
19
25
32
39
49
56
66
75
93
102
132
165
Outside diameters pipe in 250 and 300 mm sizes exceed iron pipe dimensions of ISO 559-1977
(273 and 324 mm, respectively) and cast iron pipe dimensions of ISO 13-1 978 (274 and 326 mm,
respectively).
Ultimate collapse
pressure
Ultimate collapse pressure (ultimate short term external failure pressure) at 65 C.

Nominal Internal Pressure static*
2000M
Pipe Size

[mm]
[inch]
[bar]
[bar]
25
1
25
702
40
1.5
25
191
50
2
25
105
80
3
25
29.2
100
4
25
31.9
125
5
17.2
16.2
150
6
17.2
9.3
200
8
17.2
9.9
250
10
17.2
10.2
300
12
17.2
10.1
350
14
17.2
10.3
400
16
17.2
10.3
450
18
17.2
10.1
500
20
17.2
10.2
550
22
17.2
10.2
600
24
17.2
10.3
650
26
17.2
10.3
700
28
17.2
10.4
750
30
17.2
10.3
800
32
17.2
10.4
900
36
17.2
10.4
1000
40
17.2
10.6
7000M
[bar]
742
198
108
29.7
32.4
16.4
9.4
10.0
10.3
10.1
10.3
10.4
10.2
10.2
10.3
10.3
10.3
10.4
10.3
10.4
10.5
10.6
* Up to 93C.
Dimensions for Quick-Lock bell & spigot adhesive bonded joints.
Quick-Lock
dimensions
0,5
Nominal
Pipe Size

[mm] [inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
Insertion Spigot Diameter Spigot Length

Depth
Min
Max
Max
Min
(Ds)
Sd
Sd
L
L
[mm]
[mm]
[mm]
[mm]
[mm]
27
32.6
32.9
28.5
31.0
32
47.5
47.8
33.5
36.0
46
59.2
59.6
49.0
52.0
46
87.6
88.0
49.0
52.0
46
112.5
112.9
49.0
52.0
57
139.5
139.9
58.5
61.5
57
166.2
166.6
59.0
62.0
Taper/Taper
dimensions
Dimensions for adhesive Taper spigots for adhesive bonded Taper/Taper joints.
Sd
Nose
DS
Nominal
Taper
Insertion
Pipe Size
Angle
Depth

X
Ds
[mm]
[inch]
[degrees]
[mm]
200
8
2.5
65
250
10
2.5
80
300
12
2.5
95
350
14
2.5
100
400
16
2.5
110
450
18
2.5
114
500
20
2.5
127
600
24
2.5
178
700
28
1.75
178
750
30
1.75
178
800
32
1.75
178
900
36
1.75
203
1000
40
1.75
320
Nominal
Spigot
Nose thickn.
Nose
[mm]
3.1
4.1
4.7
5.2
6.1
4.6
5.0
3.8
6.4
4.2
8.9
5.6
8.1
Dia of
Spigot
at Nose
Sd
[mm]
215.0
271.0
323.0
348.0
398.0
443.0
492.2
586.3
712.9
758.4
817.8
911.3
1016.3
Span length
Bondstrand 2000M
Nominal
Single
Continuous
Pipe Size
Span*
Span*
[mm]
[inch]
[m]
[m]
25
1
2.6
3.3
40
1.5
2.9
3.7
50
2
3.1
4.0
80
3
3.5
4.5
100
4
4.0
5.1
125
5
4.3
5.4
150
6
4.5
5.7
200
8
5.1
6.5
250
10
5.8
7.3
300
12
6.3
8.0
350
14
6.5
8.3
400
16
7.0
8.8
450
18
7.4
9.3
500
20
7.7
9.8
600
24
8.5
10.8
700
28
9.3
11.8
750
30
9.6
12.2
800
32
10.0
12.7
900
36
10.5
13.4
1000
40
11.1
14.1

Bondstrand 7000M

Nominal
Single
Continuous
Pipe Size
Span*
Span*
[mm]
[inch]
[m]
[m]
25
1
2.5
3.3
40
1.5
2.9
3.8
50
2
3.1
4.1
80
3
3.5
4.5
100
4
4.0
5.2
125
5
4.3
5.6
150
6
4.5
5.9
200
8
5.0
6.5
250
10
5.7
7.3
300
12
6.2
8.0
350
14
6.4
8.3
400
16
6.9
8.8
450
18
7.3
9.3
500
20
7.7
9.8
600
24
8.4
10.8
700
28
9.3
11.8
750
30
9.6
12.2
800
32
9.9
12.7
900
36
10.5
13.4
1000
40
11.1
14.1
Span recommendations are based on pipes filled with water having a density of 1000kg/m3 and
include no provisions for weights caused by valves, flanges or other heavy objects.
As per ISO 14692 recommendation, the maximum support span used is 6.0 m.
Elbows 90
Quick-Lock
Filament-wound 90 elbows with integral Quick-Lock (1-6 inch) or T

aper/Taper (8-40 inch)
socket ends for adhesive bonding.
Nominal
Pipe Size

[mm]
[inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
550
22
600
24
650
26
700
28
750
30
800
32
900
36
1000
40
Laying
Length
(LL)
[mm]
65
81
76
114
152
195
229
315
391
472
364
402
458
508
559
584
660
711
762
813
915
1065
Overall Max. Working

Length
Pressure
(OL)
[mm]
[bar]
92
25
113
25
122
25
160
25
198
25
252
17.2
286
17.2
380
17.2
471
17.2
567
17.2
464
17.2
512
17.2
572
17.2
635
17.2
711
17.2
762
17.2
838
17.2
889
17.2
940
17.2
991
17.2
1118
17.2
1385
17.2
Average
Weight
[kg]
0.3
0.4
0.5
1.1
1.6
2.7
3.6
6.8
11
18
26
31
53
65
94
122
180
205
243
330
417
489
Taper/Taper
Elbows 45
Quick-Lock
Filament-wound 45 Quick-Lock (1-6 inch) and Taper/Taper (8-40 inch) socket ends for
adhesive bonding.
Nominal
Pipe
Size
[mm]
[inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
800
32
900
36
1000
40
Laying
Length
(LL)
[mm]
22
29
35
51
64
84
95
137
169
205
125
142
191
210
252
295
322
337
400
475
Overall
Length
(OL)
[mm]
49
61
81
97
110
141
152
202
249
300
225
252
305
337
430
473
500
515
603
798
Maximum
Working
Pressure
[bar]
25
25
25
25
25
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
Average
Weight
[kg]
0.2
0.3
0.4
0.8
1.1
1.8
2.4
4.3
7.3
11.0
17.0
20.0
33
40
82
140
164
283
283
334
Taper/Taper
Elbows 22
Quick-Lock
Taper/Taper
10
Filament-wound 22 elbows with integral Quick-Lock (1-6 inch) and Taper/Taper (8-40
inch) socket ends for adhesive bonding.
Nominal
Pipe
Size
[mm]
[inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
900
36
1000
40
Laying
Length
(LL)
[mm]
9
9
13
21
29
43
43
76
68
86
71
85
110
101
122
142
152
182
258
Overall
Length
(OL)
[mm]
36
41
59
67
75
100
100
141
148
181
171
195
224
228
300
320
330
385
578
Maximum
Working
Pressure
[bar]
25
25
25
25
25
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
Average
Weight
[kg]
0.1
0.2
0.5
0.7
1
1.4
1.9
3.9
5.9
10.4
12
14
23
28
57
98
115
198
234
Equal Tees
Quick-Lock
Filament-wound equal Tee with integral Quick-Lock (1-6 inch) or Taper/Taper (8-40 inch)
socket ends for adhesive bonding.
Nominal
Pipe
Size

[mm] [inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
800
32
900
36
1000
40
Laying
Length
total run
(LL1)
[mm]
54
60
128
172
210
254
286
376
452
546
544
590
648
712
838
964
1016
1090
1220
1466
Overall
Length
total run
(OL1)
[mm]
108
124
220
264
302
368
400
506
612
736
744
810
876
966
1194
1320
1372
1446
1626
2106
Laying
Length
branch
(LL2)
[mm]
27
30
64
86
105
127
143
188
226
273
272
295
324
356
419
482
508
545
610
733
Overall
Length
branch
(OL2)
[mm]
54
62
110
132
151
184
200
253
306
368
372
405
438
483
597
660
686
723
813
1053
Maximum
Working
Pressure
Average
Weight
[bar]
25
25
25
25
25
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
[kg]
0.2
0.4
1
1.8
2.5
5
6.7
10
18
29
37
56
69
92
168
285
337
459
581
686
Taper/Taper
11
Reducing Tees
Filament-wound standard and fabricated reducing tees with integral Quick-Lock (1-6 inch)
or Taper/Taper (8-40 inch) socket ends for adhesive bonding.
Nominal
Pipe
Size
(runxbranch)
Quick-Lock Filament wound
Quick-Lock Fabricated
Taper/Taper Filament wound
Taper/Taper Fabricated
[mm]
40x25
50x25
50x40
80x25
80x40
80x50
100x25
100x40
100x50
100x80
125x50
125x80
125x100
150x25
150x40
150x50
150x80
150x100
150x125
200x25
200x40
200x50
200x80
200x100
200x150
250x25
250x40
250x50
250x80
250x100
250x150
250x200
300x25
300x40
300x50
300x80
300x100
300x150
300x200
300x250
Laying Overall
Length Length
(LL1)
(OL1)
half run
half run
Laying
Length
(LL2)
branch
Overall Maximum Average

Length Working Weight
(OL2) Pressure
branch
[inch]
[mm]
[mm]
[mm]
[mm]
[bar]
[kg]
1.5x1
30
62
30
57
25
0.6
2x1
64
110
57
84
25
0.9
2x1.5
64
110
57
89
25
1
3x1
86
132
76
103
25
1.6
3x1.5
86
132
76
108
25
1.6
3x2
86
132
76
122
25
1.7
4x1 72 118 194 221 25 7.5
4x1.5 89 136 194 226 25 9.0
4x2
105
151
89
135
25
2.1
4x3
105
151
98
144
25
2.3
5x2
127
184
102
148
17.2
3.4
5x3
127
184
111
157
17.2
4
5x4
127
184
118
164
17.2
4.6
6x1 83 140 221 248 17.2
11.7
6x1.5 101 158 221 253 17.2
13.8
6x2
143
200
114
160
17.2
6.2
6x3
143
200
124
170
17.2
5.7
6x4
143
200
130
176
17.2
5.9
6x5
143
200
136
193
17.2
6.2
8x1 88 153 245 272 17.2
15.0
8x1.5 88 153 246 278 17.2
17.5
8x2 88 153 245 291 17.2
19.9
8x3
188
253
149
195
17.2
9.1
8x4
188
253
162
208
17.2
9.7
8x6
188
253
168
225
17.2
11.4
10x1 88 168 273 300 17.2
18.1
10x1.5 88 168 273 305 17.2 21
10x2 88 168 273 318 17.2 24
10x3 100 180 273 318 17.2 24
10x4
226
306
184
230
17.2
14.8
10x6
226
306
194
251
17.2
15.5
10x8
226
306
203
268
17.2
16.5
12x1 88 183 298 325 17.2 21
12x1.5 88 183 298 330 17.2 25
12x2 88 183 298 344 17.2 29
12x3 100 195 298 344 17.2 29
12x4
273
368
206
252
17.2
21
12x6
273
368
219
276
17.2
22
12x8
273
368
229
294
17.2
23
12x10
273
368
241
321
17.2
24
Note: Regular numbers are filament wound tees; Italic numbers are fabricated tees.
12
Reducing Tees (cont)
Nominal
Pipe
Size
(runxbranch)
[mm]
350x25
350x40
350x50
350x80
350x100
350x150
350x200
350x250
350x300
400x25
400x40
400x50
400x80
400x100
400x150
400x200
400x250
400x300
400x350
450x25
450x40
450x50
450x80
450x100
450x150
450x200
450x250
450x300
450x350
450x400
500x25
500x40
500x50
500x80
500x100
500x150
500x250
500x300
500x350
500x400
500x450
Laying Overall
Length Length
(LL1)
(OL1)
half run
half run
Laying
Length
(LL2)
branch

(OL2) Pressure
branch
[inch]
[mm]
[mm]
[mm]
[mm]
[bar]
[kg]
14x1 88 188 314 341 17.2 24
14x1.5 88 188 314 346 17.2 28
14x2 88 188 314 361 17.2 31
14x3 100 200 314 361 17.2 31
14x4 113 213 314 361 17.2 31
14x6
272
372
244
301
17.2
29
14x8
272
372
254
319
17.2
30
14x10
272
372
267
347
17.2
32
14x12
272
372
288
383
17.2
34
16x1 88 198 338 365 17.2 29
16x1.5 88 198 338 370 17.2 33
16x2 88 198 338 384 17.2 37
16x3 100 210 338 384 17.2 37
16x4 113 223 338 384 17.2 37
16x6
295
405
264
321
17.2
37
16x8
295
405
273
338
17.2
38
16x10
295
405
283
363
17.2
41
16x12
295
405
304
399
17.2
45
16x14
295
405
292
392
17.2
49
18x1 88 202 358 385 17.2 31
18x1.5 88 202 358 390 17.2 31
18x2 88 202 358 404 17.2 22
18x3 100 214 358 404 17.2 35
18x4 113 227 358 404 17.2 38
18x6 138 252 367 424 17.2 45
18x8
324
438
306
370
17.2
53
18x10
324
438
319
399
17.2
60
18x12
324
438
328
423
17.2
67
18x14
324
438
317
417
17.2
66
18x16
324
438
319
429
17.2
69
20x1 88 215 382 409 17.2 35
20x1.5 88 215 382 414 17.2 35
20x2 88 215 382 428 17.2 36
20x3 100 227 382 428 17.2 39
20x4 113 240 382 428 17.2 43
20x6 138 265 391 448 17.2 50
20x10
356
483
344
414
17.2
77
20x12
356
483
354
449
17.2
82
20x14
356
483
343
443
17.2
85
20x16
356
483
344
454
17.2
85
20x18
356
483
350
464
17.2
89
Note: Tees main-run (18-40 inch) with Quick-Lock socket branch (1-6 inch) are fabricated Tees.
Regular numbers are filament wound tees; Italic numbers are fabricated tees.
13
Nominal
Pipe
Size
(runxbranch)
[mm]
550x200
550x250
550x300
550x350
550x400
550x450
550x500
600x25
600x40
600x50
600x80
600x100
600x150
600x200
600x250
600x300
600x350
600x400
600x450
600x500
700x25
700x40
700x50
700x80
700x100
700x150
700x350
700x400
700x450
700x500
700x600
750x25
750x40
750x50
750x80
750x100
750x150
750x300
750x350
750x400
750x450
750x500
750x600
Laying Overall
Length Length
(LL1)
(OL1)
half run
half run
Laying
Length
(LL2)
branch

(OL2) Pressure
branch
[inch]
[mm]
[mm]
[mm]
[mm]
[bar]
[kg]
22x8
388
540
357
422
17.2
80
22x10
388
540
370
450
17.2
85
22x12
388
540
379
474
17.2
90
22x14
388
540
368
468
17.2
94
22x16
388
540
370
480
17.2
94
22x18
388
540
375
489
17.2
98
22x20
388
540
381
508
17.2
102
24x1 88 266 430 457 17.2 51
24x1.5 88 266 430 462 17.2 51
24x2 88 266 430 476 17.2 52
24x3 100 278 430 476 17.2 56
24x4 113 291 430 476 17.2 61
24x6 138 316 439 496 17.2 69
24x8
419
597
412
477
17.2
78
24x10
419
597
386
466
17.2
85
24x12
419
597
417
512
17.2
85
24x14
419
597
394
494
17.2
101
24x16
419
597
395
505
17.2
99
24x18
419
597
413
527
17.2
137
24x20
419
597
406
533
17.2
156
28x1 88 266 491 518 17.2 59
28x1.5 88 266 491 523 17.2 59
28x2 88 266 491 537 17.2 59
28x3 100 278 491 537 17.2 64
28x4 113 291 491 537 17.2 70
28x6 138 316 500 557 17.2 80
28x14
482
660
490
590
17.2
147
28x16
482
660
500
610
17.2
166
28x18
482
660
500
614
17.2
189
28x20
482
660
506
633
17.2
210
28x24
482
660
506
684
17.2
252
30x1 88 266 516 543 17.2 63
30x1.5 88 266 516 548 17.2 63
30x2 88 266 516 562 17.2 63
30x3 100 278 516 562 17.2 69
30x4 113 291 516 562 17.2 74
30x6 138 316 525 582 17.2 85
30x12
508
686
765
860
17.2
118
30x14
508
686
722
822
17.2
157
30x16
508
686
698
808
17.2
178
30x18
508
686
488
602
17.2
202
30x20
508
686
495
622
17.2
225
30x24
508
686
481
659
17.2
270
14
Nominal
Pipe
Size
(runxbranch)
[mm]
800x25
800x40
800x50
800x80
800x100
800x150
800x500
800x600
800x700
800x750
900x25
900x40
900x50
900x80
900x100
900x150
900x400
900x450
900x500
900x600
900x700
900x750
1000x25
1000x40
1000x50
1000x80
1000x100
1000x600
1000x700
1000x750
1000x800
1000x700
Laying Overall
Length Length
(LL1)
(OL1)
half run
half run
Laying
Length
(LL2)
branch

(OL2) Pressure
branch
[inch]
[mm]
[mm]
[mm]
[mm]
[bar]
[kg]
32x1 88 266 541 568 17.2 66
32x1.5 88 266 541 573 17.2 67
32x2 88 266 541 587 17.2 67
32x3 100 278 541 587 17.2 73
32x4 113 291 541 587 17.2 79
32x6 138 316 550 607 17.2 90
32x20
545
723
523
650
17.2
258
32x24
545
723
523
701
17.2
310
32x28
545
723
532
710
17.2
348
32x30
545
723
534
712
17.2
387
36x1 88 291 591 618 17.2 78
36x1.5 88 291 591 623 17.2 78
36x2 88 291 591 637 17.2 78
36x3 100 303 591 637 17.2 85
36x4 113 316 591 637 17.2 92
36x6 138 341 600 657 17.2 105
36x16
610
813
563
673
17.2
270
36x18
610
813
563
677
17.2
290
3620
610
813
563
690
17.2
323
36x24
610
813
541
719
17.2
387
36x28
610
813
570
748
17.2
459
36x30
610
813
584
762
17.2
484
40x1 120 440 641 668 17.2 92
40x1.5 120 440 641 673 17.2 92
40x2 120 440 641 687 17.2 92
40x3 132 452 641 687 17.2 100
40x4 145 465 641 687 17.2 100
40x24
733
1053
593
771
17.2
456
40x28
733
1053
632
810
17.2
541
40x30
733
1053
633
811
17.2
571
40x32
733
1053
652
830
17.2
605
40x36
733
1053
652
855
17.2
634
15
Fabricated Reducing
Tees with Flanged
Branch
Fabricated Reducing tees with integral Quick-Lock (4-6 inch) or Taper (8-16 inch) socket
ends and flanged branch.
Nominal
Pipe
Size
(runxbranch)
Quick-Lock
Taper/Taper
[mm]
100x25
100x40
150x25
150x40
200x25
200x40
200x50
250x25
250x40
250x50
250x80
300x25
300x40
300x50
300x80
350x25
350x40
350x50
350x80
350x100
400x25
400x40
400x50
400x80
400x100
[inch]
4x1
4x1.5
6x1
6x1.5
8x1
8x1.5
8x2
10x1
10x1.5
10x2
10x3
12x1
12x1.5
12x2
12x3
14x1
14x1.5
14x2
14x3
14x4
16x1
16x1.5
16x2
16x3
16x4
Laying
Length
(LL1)
Overall
Length
(OL1)
Laying
Length
(LL2)
[mm]
72
89
83
101
88
88
88
88
88
88
100
88
88
88
100
88
88
88
100
113
85
103
118
118
118
[mm]
118
135
140
158
153
153
153
168
168
168
180
183
183
183
195
188
188
188
200
213
187
205
220
220
220
[mm]
224
229
251
256
276
281
295
303
308
322
323
329
334
348
349
344
349
363
364
364
369
374
388
389
389
half run
half run
branch
Maximum
Working
Pressure

[bar]
25
25
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
Average
Weight
[kg]
8.0
9.7
12.2
14.5
15.5
18.2
21
18.6
22
26
26
22
26
30
31
24
28
33
33
34
29
34
39
39
40
Note: Other sizes, or multiple size branched tees available on request. Please contact NOV Fiber
Glass Systems.
16
Fabricated Reducing
Tees with Flanged
Branch (cont)
Fabricated Reducing tees with integral Taper (18-40 inch) socket ends and flanged branch.
Nominal
Pipe
Size
(runxbranch)
Quick-Lock
Taper/Taper
[mm]
450x25
450x40
450x50
450x80
450x100
450x150
500x25
500x40
500x50
500x80
500x100
600x25
600x40
600x50
600x80
600x100
650x25
650x40
650x50
650x80
650x100
700x25
700x40
700x50
700x80
700x100
750x25
750x40
750x50
750x80
750x100
800x25
800x40
800x50
800x80
800x100
900x25
900x40
900x50
900x80
900x100
1000x25
1000x40
1000x50
1000x80
1000x100
[inch]
18x1
18x1.5
18x2
18x3
18x4
18x6
20x1
20x1.5
20x2
20x3
20x4
24x1
24x1.5
24x2
24x3
24x4
2x1
26x1.5
26x2
26x3
26x4
28x1
28x1.5
28x2
28x3
28x4
30x1
30x1.5
30x2
30x3
30x4
32x1
32x1.5
32x2
32x3
32x4
36x1
36x1.5
36x2
36x3
36x4
40x1
40x1.5
40x2
40x3
40x4
Laying
Length
(LL1)
Overall
Length
(OL1)
Laying
Length
(LL2)
[mm]
88
88
88
100
113
138
88
88
88
100
113
88
88
88
100
113
88
88
88
100
113
88
88
88
100
113
88
88
88
100
113
88
88
88
100
113
88
88
88
100
113
120
120
120
132
145
[mm]
202
202
202
214
227
252
215
215
215
227
240
266
266
266
278
291
266
266
266
278
291
266
266
266
278
291
266
266
266
278
291
266
266
266
278
291
291
291
291
303
316
440
440
440
452
465
[mm]
388
394
408
409
409
430
412
418
432
433
433
460
467
480
481
481
497
502
516
517
517
521
527
541
542
542
546
552
566
567
567
571
576
590
590
590
621
627
641
642
642
672
677
691
692
692
half run
half run
branch
Maximum
Working
Pressure

[bar]
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
Average
Weight
[kg]
32
32
33
37
41
49
36
36
37
41
46
52
52
53
58
63
78
78
78
83
88
59
59
61
67
73
63
63
64
71
77
67
67
68
75
82
78
79
80
87
94
92
93
94
103
113
Note: Other sizes, or multiple size branched tees available on request. Please contact NOV Fiber
Glass Systems.
17
Bushing Saddles
Filament-wound pipe saddles with stainless steel, 1/2 inch and 3/4 inch threaded bushings.*

Nominal
Angle Saddle
Saddle Maximum Average
Required
Pipe
Length
Thickn. Working
Weight
Adhesive
Size

(B)
(ts) Pressure
Kits
[mm] [inch] [degree]
[mm]
[mm]
[bar]
[kg]
[3 Oz] [6 Oz]
50
2
180
100
14
17.2
0.5
1
80
3
180
100
14
17.2
0.6
1
100
4
180
100
14
17.2
0.8
1
125
5
180
100
14
17.2
0.9
-
1
150
6
180
100
14
17.2
1.0
-
1
200
8
180
100
14
17.2
1.2
-
1
250
10
180
100
14
17.2
1.6
1
1
300
12
180
100
14
12
1.9
1
1
350
14
180
100
14
12
2.1
1
1
400
16
180
100
14
12
2.5
-
2
450
18
90
100
14
12
3.3
-
1
500
20
90
100
14
12
3.7
1
1
600
24
90
100
14
12
4.4
-
2
* Consult NOV Fiber Glass Systems for other type material, or other sized bushings.
For higher pressures, above 17.2/12 bar, please contact NOV Fiber Glass Systems.
45 Laterals
Filament-wound 45 laterals with integral Quick-Lock (2-6 inch) or Taper/Taper (8-16 inch)
socket ends, for adhesive bonding.
Nominal
Pipe
Size
[mm] [inch]
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
18
Laying
Length
(LL1)
[mm]
64
76
76
89
89
124
137
159
150
150
Overall
Length
(OL1)
[mm]
110
122
122
146
146
189
217
254
250
260
Laying
Length
(LL2)
[mm]
203
254
305
337
368
455
531
641
632
632
Overall
Length
(OL2)
[mm]
249
300
351
394
425
520
611
736
732
742
Maximum Average
Working Weight
Pressure
[bar]
[kg]
17.2
1.6
17.2
3.0
17.2
3.9
17.2
5.8
17.2
6.8
17.2
12.0
12
21
12
30
12
39
12
54
Concentric Reducers
Quick-Lock
Taper/Taper
Filament-wound concentric reducers with integral Quick-Lock (1-6 inch) or Taper/Taper

(8-40 inch) socket ends, for adhesive bonding.

Nominal
Laying
Overall
Maximum
Average
Pipe Size
Length
Length
Working
Weight
(runxrun)
(LL)
(OL)
Pressure
[mm]
[inch]
[mm]
[mm]
[bar]
[kg]
40x25
1.5x1
32
91
25
0.2
50x25
2x1
64
137
25
0.3
50x40
2x1.5
32
110
25
0.5
80x40
3x1.5
76
154
25
0.5
80x50
3x2
54
146
25
0.5
100x50
4x2
76
168
25
1.1
100x80
4x3
73
165
25
0.9
125x80
5x3
74
177
17.2
1.4
125x100
5x4
74
177
17.2
1.5
150x80
6x3
97
200
17.2
1.8
150x100
6x4
94
197
17.2
1.8
150x125
6x5
110
224
17.2
1.8
200x100
8x4
153
264
17.2
2.9
200x150
8x6
119
241
17.2
2.7
250x150
10x6
138
275
17.2
3.7
250x200
10x8
135
280
17.2
3.6
300x200
12x8
189
349
17.2
5.0
300x250
12x10
176
351
17.2
4.6
350x250
14x10
214
394
17.2
7.2
350x300
14x12
217
412
17.2
7.3
400x300
16x12
204
409
17.2
8.9
400x350
1x14
183
393
17.2
9.0
450x400
18x16
113
337
17.2
12.7
500x400
20x16
235
472
17.2
23
500x450
20x18
123
364
17.2
18.9
550x400
22x16
340
602
17.2
36
550x450
22x18
228
494
17.2
32
550x500
22x20
106
385
17.2
29
600x400
24x16
463
751
17.2
48
600x450
24x18
353
645
17.2
44
600x500
24x20
230
535
17.2
39
600x550
24x22
126
456
17.2
36
700x400
28x16
775
1063
17.2
79
700x450
28x1
661
953
17.2
74
700x500
28x20
542
847
17.2
69
700x600
28x24
311
667
17.2
67
750x400
30x16
886
1174
17.2
112
750x450
30x18
775
1067
17.2
107
750x500
30x20
653
958
17.2
100
750x600
30x24
422
778
17.2
87
750x650
30x26
240
596
17.2
72
750x700
30x28
111
467
17.2
57
800x450
32x18
920
1212
17.2
125
800x500
32x20
798
1103
17.2
109
800x600
32x24
570
926
17.2
94
800x700
32x28
259
615
17.2
82
800x750
32x30
148
504
17.2
71
900x500
36x20
1029
1359
17.2
210
900x600
36x24
799
1180
17.2
176
900x700
36x28
487
868
17.2
140
900x750
36x30
375
756
17.2
126
1000x900
40x36
310
833
17.2
182
19
Eccentric Reducers
Quick-Lock
Taper/Taper
20
Filament-wound Eccentric Reducers with integral Quick-Lock (1-6 inch) or Taper/Taper

(8-40 inch) socket ends, for adhesive bonding.

Nominal
Laying
Overall Eccentricity Maximum Average
Pipe Size
Length
Length
Working
Weight
(runxrun)
(LL)
(OL)
(X)
Pressure
[mm]
[inch]
[mm]
[mm]
[mm]
[bar]
[kg]
40x25
1.5x1
56
115
7
25
0.2
50x25
2x1
100
173
13
25
0.3
50x40
2x1.5
44
122
6
25
0.5
80x40
3x1.5
150
228
20
25
0.5
80x50
3x2
108
200
14
25
0.5
100x50
4x2
200
292
27
25
1.1
100x80
4x3
93
185
12
25
0.9
125x100
5x4
101
204
14
17.2
1.5
150x80
6x3
293
396
39
17.2
1.8
150x100
6x4
200
303
27
17.2
1.8
150x125
6x5
100
214
13
17.2
1.8
200x100
8x4
405
516
52
17.2
2.9
200x150
8x6
205
327
25
17.2
2.7
250x150
10x6
410
547
53
17.2
3.7
250x200
10x8
235
380
27
17.2
3.6
300x200
12x8
429
589
53
17.2
5.0
300x250
12x10
229
404
26
17.2
4.6
350x250
14x10
340
520
42
17.2
7.2
350x300
14x12
159
354
16
17.2
7.3
400x300
16x12
344
549
41
17.2
8.9
400x350
16x14
215
425
25
17.2
9.0
450x300
18x12
450
640
63
17.2
15.6
450x350
18x14
322
525
43
17.2
14.2
450x400
18x16
197
413
18
17.2
12.7
500x400
20x16
324
553
39
17.2
23
500x450
20x18
197
438
22
17.2
18.9
600x400
24x16
580
860
93
17.2
48
600x450
24x18
450
742
73
17.2
44
600x500
24x20
325
630
48
17.2
39
750x400
30x24
451
807
86
17.2
87
900x400
36x24
832
1213
161
17.2
176
1000x800
40x32
739
1237
100
17.2
182
1000x900
40x36
419
942
52
17.2
192
Couplings
Quick-Lock
Filament-wound couplings with integral Quick-Lock (1-6 inch) or Taper/Taper (8-40 inch)
socket ends, for adhesive bonding.
Nominal
Pipe
Size
[mm] [inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
800
32
900
36
1000
40
Laying
Length
(LL)
[mm]
10
10
10
10
10
10
10
70
70
70
70
70
70
70
70
70
70
70
70
70
Overall
Length
(OL)
[mm]
64
74
102
102
102
124
124
200
230
260
270
290
298
324
426
426
426
426
476
710
Outside
Diameter
(OD)
[mm]
42
58
72
100
129
153
183
235
289
340
372
422
460
514
619
742
795
848
950
1057
Maximum
Working
Pressure
[bar]
25
25
25
25
25
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
Average
Weight
[kg]
0.1
0.1
0.3
0.4
0.6
0.9
1.1
1.7
2.3
2.8
4.6
7.2
10.7
13.0
18.8
24
25
27
35
41
Taper/Taper
Nipples
Quick-Lock
Filament-wound nipples with integral Quick-Lock (1-6 inch) or Taper/Taper (8-40 inch)
male ends, for adhesive bonding.
Nominal
Pipe
Size
[mm]
[inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
800
32
900
36
1000
40
Laying
Gap*
Length
(LL)

[mm]
[mm]
57
3
67
3
95
3
95
3
95
3
117
3
117
3
160
30
190
30
230
40
240
40
260
40
278
50
304
50
406
50
406
50
406
50
406
50
456
50
690
50
Maximum
Working
Pressure
[bar]
25
25
25
25
25
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
17.2
Average
Weight
[kg]
0.1
0.1
0.1
0.1
0.2
0.3
0.4
0.6
0.9
1.1
3.1
4.4
5.9
7.8
12
21
22
24
36
51
* Remaining gap after bonding.

Taper/Taper
21
Support Saddles
Filament-wound pipe saddles for wear, support and anchor.

Nominal Saddle
Pipe

Angle
Size

[mm] [inch] [degree]
25
1
180
40
1.5
180
50
2
180
80
3
180
100
4
180
125
5
180
150
6
180
200
8
180
250
10
180
300
12
180
350
14
180
400
16
180
450
18
180
500
20
180
600
24
180
700
28
180
750
30
180
800
32
180
900
36
180
1000
40
180
Saddle Saddle
Thickn. Weight
ts B=100mm
[mm]
[kg]
14
0.2
14
0.3
14
0.4
14
0.5
14
0.7
14
0.8
14
0.9
14
1.1
14
1.5
14
1.8
14
2.0
14
2.4
16
-
16
-
16
-
16
-
16
-
16
-
16
-
16
-
Required
Saddle
Required
Adhesive
Weight
Adhesive
Kits B=150mm
Kits
[3 and 6Oz]
[kg] [3 and 6 Oz]
1
-
0.3
1
1
-
0.5
1
1
-
0.6
1
1
-
0.8
-
1
1
-
1.1
-
1
-
1
1.2
-
1
-
1
1.4
-
1.5
-
1
1.7
-
1.5
-
1.5
2.3
-
2
-
1.5
2.7
-
2.5
-
1.5
3.0
-
2.5
-
2
3.6
-
3
-
-
3.2
-
2
-
-
3.6
-
2
-
-
4.3
-
2
-
-
5.1
-
3
-
-
5.5
-
3
-
-
5.8
-
3
-
-
6.5
-
4
-
-
8.2
-
4
Notes:
1) Filament-wound support saddles are intended for protection of pipe at supports and clamps, as
well as for anchoring purposes. Support and anchor saddles are standard 180. Saddles are
sup plied in standard lengths of 100 mm and 150 mm.
2) For special saddle -lengths, -thickness and/or angles consult NOV Fiber Glass Systems.
3) Wear saddles are standard 90. Weights of 90 degree saddles are 50% of value shown.
22
Grounding Saddles
Filament-wound pipe saddles for grounding in conductive piping systems.

Nominal
Required
Pipe
Size
[mm] [inch]
25
1
40
1.5
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
800
32
900
36
1000
40
Saddle
Saddle
Saddle
Average
Angle

[degree]
90
90
90
90
90
90
90
45
45
45
45
45
22.5
22.5
22.5
22.5
22.5
22.5
22.5
22.5
Length
B
[mm]
76
76
76
76
76
76
76
76
76
76
76
76
76
76
76
76
76
76
76
76
Thickness
t s
[mm]
14
14
14
14
14
14
14
14
14
14
14
14
16
16
16
16
16
16
16
16
Saddle
Weight
[kg]
0.1
0.1
0.1
0.1
0.2
0.3
0.3
0.2
0.2
0.2
0.3
0.3
0.2
0.2
0.3
0.3
0.4
0.4
0.4
0.5
Adhesive
Kits
[3Oz]
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
3
3
3
Notes:
1) Bondstrand conductive adhesive should be used for mounting.
2) Saddles are supplied with integrated stainless steel cable with a length of 600 mm.
Bell Mouths
Filament-wound bell mouths with adhesive-bonded HD-flange.

Nominal
Pipe
Size
[mm] [inch]
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
Overall
Length
(OL)
[mm]
269
274
289
323
324
534
604
588
616
596
627
724
831
Length of
Bell Mouth
(H1)
[mm]
115
120
135
158
158
340
395
365
375
345
360
450
540
Internal
Diameter
(D1)
[mm]
110
220
275
400
450
750
850
850
850
850
900
1100
1300
Internal
Diameter
(D2)
[mm]
110
220
275
400
450
418
518
510
510
510
548
548
648
Average
Weight*
[kg]
3.1
5.0
8.4
12.7
14.7
26
39
51
60
67
90
119
171
* Weights provided are for bell mouth with CL150 flange.
23
Assembly of double
O-ring expansion joint
Expansion Coupling
Filament-wound Key-Lock expansion coupling with integral double O-ring Key-Lock female
end one side and double O-ring female end on other side.
Nominal
Pipe
Size
[mm] [inch]
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
800
32
900
36
1000
40
24
Laying
Length
(LL)
[mm]
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
Overall
O-ring
Key
Length
Size
Size
(OL)
[mm]
[mm]
[mm]
222
7 x 59.7
6 x 305
222
7 x 88.3
6 x 400
222
7 x 113.7
6 x 483
264
9 x 135
8 x 580
270
10 x 161.3
8 x 660
339
10 x 225.5
10 x 840
376
12.5 x 302
12 x 1270
478
12.5 x 342.3
15 x 1270
452
12.5 x 342.3
15 x 1360
496
12.5 x 393.1
18 x 1585
416
15.0 x 445.0
15 x 1750
433
15.0 x 490.0
15 x 1930
479
18.0 x 580.0
18 x 2240
560
20.0 x 685.0
20 x 2700
574
20.0 x 740.0
20 x 2700
644
20.0 x 790.0
20 x 3065
754
25.0 x 890.0
25 x 3175
740
26.0 x 987.0
20 x 3500
Average
Weight
[kg]
1.3
1.7
3.5
4.6
6.6
15.4
19.9
21
25
32
27
32
52
77
90
115
170
208
Key-Lock Adapter for

Expansion Coupling
Quick-Lock
Filament-wound double O-ring male Key-Lock adapter with integral Quick-Lock (2-6 inch)
or Taper/Taper (8-40 inch) socket end, for adhesive bonding.
Nominal
Pipe
Size
[mm]
[inch]
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
800
32
900
36
1000
40
Laying
Length
(LL)
[mm]
85
85
85
102
105
149
158
185
195
205
193
201
224
265
272
307
362
355
Overall
Length
(OL)
[mm]
131
131
131
159
162
202
228
285
285
320
307
328
402
443
450
485
565
765
Average
Weight
[kg]
0.4
0.6
0.9
1.6
1.8
5.1
11.8
14.6
10.7
15.9
19.5
24
25
29
34
42
50
64
Taper/Taper
Double O-ring Adapter

for Expansion Coupling
Quick-Lock
Filament-wound double O-ring male adapter with integral Quick-Lock (1-6 inch) and Taper
(8-40 inch) socket end, for adhesive bonding.
Nominal
Pipe
Size
[mm]
[inch]
50
2
80
3
100
4
125
5
150
6
200
8
250
10
300
12
350
14
400
16
450
18
500
20
600
24
700
28
750
30
800
32
900
36
1000
40
Laying
Length
(LL)
[mm]
85
85
85
102
105
138
148
175
185
195
193
201
224
265
272
307
362
355
Overall
Length
(OL)
[mm]
131
131
131
159
162
203
228
285
285
320
307
328
402
443
450
485
565
765
Average
Weight
[kg]
0.4
0.7
0.9
1.6
1.8
5.1
11.8
14.6
10.7
15.9
19.5
24
25
29
34
42
50
64
Taper/Taper
25
Adhesive
Number of Adhesive Kits per joint.

Nominal
Pipe
Size
[mm]
[inch]
[cm3]
25
1
88.7
40
1
88.7
50
2
88.7
80
3
88.7
100
4
88.7
125
5
88.7
150
6
88.7
200
8
88.7
250
10
177.4
300
12
177.4
350
14
177.4
400
16
177.4
450
18
177.4
500
20
177.4
550
22
177.4
600
24
177.4
650
26
177.4
700
28
177.4
750
30
177.4
800
32
177.4
850
34
177.4
900
36
177.4
1000
40
177.4
Required
Adhesive Kit
Size
[Oz]
3
3
3
3
3
3
3
3
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Minimum number
of Adhesive Kits
required per joint
nr.
1/5
1/5
1/4
1/3
1/2
1
1
1
1
1
2
2
2
3
4
4
4
4
5
5
6
6
7
Notes:
1) Adhesive Kits should never be split. If remainder is not used for other joints made at the same
time, the surplus must be discarded.
2) Required adhesive for saddles is shown in the dimension table of the respective saddles.
3) For type of adhesive to be used, please refer to the Bondstrand Corrosion Guide.
26
27
Engineering design &

installation
Consult the following literature for recommendations pertaining design, installation and
installation use of Bondstrand pipe, fittings and flanges:

Assembly Instructions for Quick-Lock adhesive-bonded joints
Assembly Instructions for Taper/Taper adhesive-bonded joints
Assembly Instructions for Bondstrand fiberglass flanges
Bondstrand Corrosion Guide for fiberglass pipe and tubing
Bondstrand Pipe Shaver Overview
Bondstrand Marine Design Manual
Bondstrand Heating Blanket
Please consult NOV Fiber Glass Systems for the latest version of the above-mentioned
literature.
Specials
Note: Elbows with non-standard angles, non-standard drilled flanges, multi-branch tees
and special spools are available on request, please consult NOV Fiber Glass Systems.
Field testing
Pipe system is designed for hydrostatic testing with water at 150% of rated pressure.
Conversions
1 psi = 6895 Pa = 0.07031 kg/cm2

1 bar = 105 Pa = 14.5 psi = 1.02 kg/cm2
1 MPa = 1 N/mm2 = 145 psi = 10.2 kg/cm2
1 inch = 25.4 mm
1 Btu.in/ft2 hF = 0.1442 W/mK
C = 5/9 (F-32)
National Oilwell Varco has produced this brochure for general information only,
and it is not intended for design purposes. Although every effort has been made to
maintain the accuracy and reliability of its contents, National Oilwell Varco in no way
assumes responsibility for liability for any loss, damage or injury resulting from the use
of information and data herein. All applications for the material described are at the
users risk and are the users responsibility.
All brands listed are trademarks of National Oilwell Varco.
North America
17115 San Pedro Avenue
Suite 200
San Antonio, TX 78232 USA
Phone: +1 210 477 7500
South America
Estrada de Acesso Zona
Industrial Porturia de Suape, s/no.
Recife, PE, Brazil 55.590-000
Phone: +55 81 3501 0023
Europe
P.O. Box 6, 4190 CA
Geldermalsen, The Netherlands
Phone: +31 345 587 587
Asia Pacific
No. 7A, Tuas Avenue 3
Jurong, Singapore 639407
Phone: +65 6861 6118
Middle East
P.O. Box 17324
Dubai, UAE
Phone: +971 4881 3566
www.fgspipe.com [email protected]
2013 National Oilwell Varco. All rights reserved.

MOS2000 supersedes FP 918 C - April 2013
Bondstrand 2000M/7000M Flanges for Marine & Offshore

1 to 6 inch (Quick-Lock Joint), 8 to 40 inch (Taper/Taper Joint)
Description
Bondstrand marine flanges are produced to fit pipe of both Iron Pipe Size (IPS) and Metric Cast Iron (MCI) outside diameters for
the two types of Bondstrand marine pipe:
Bondstrand Series 2000M
A lined fiberglass pipe of reinforced epoxy resins in 1-through 40-inch diameters intended for a broad range of shipboard uses,
including fresh and seawater piping, ballast systems, portable discharge lines, inert gas effluent systems, and applications where
resistance to corrosive fluids is required. Bondstrand 2000M flanges are not electrically conductive.
Bondstrand Series 7000M
An unlined fiberglass pipe of reinforced epoxy resins in 1-through 40-inch diameters containing integrally wound electrically
conductive fibers for use where the accumulation of static electrical charges on the surface of the pipe is to be avoided. Bondstrand
7000M provide electrical continuity when assembled to other conductive flanges.
Consult NOV Fiber Glass Systems for the availability of flanges for any sizes not listed.
Configurations
Bondstrand Taper marine flanges are produced in two configurations:
Fixed bolt-hole orientation, Heavy-duty type
Loose-ring, rotatable bolt-hole orientation, Stub End/ Flange Ring (Van Stone type)
Joint system: Quick-Lock joint is for pipe size 1 to 6 inch and Taper/Taper adhesive joint applied for size 8 to 40 inch.
Quick-Lock adhesive bonded joint
Taper/Taper adhesive bonded joint
Drillings
ASME B16.5 Class 150 (1 to 24 inch)
ASME B16.5 Class 300 (1 to 24 inch)
ASME B16.47 A Class 150 (26 to 40 inch)
ISO 7005 PN-10
ISO 7005 PN-16
JIS B2220 - 5 kg/cm2
JIS B2220 - 10 kg/cm2
JIS B2220 - 16 kg/cm2
Other drillings, as well as undrilled flanges, are also available.
Performance
See Product Data of the appropriate Bondstrand pipe system for pressure and temperature performances. Consult Bondstrand
Corrosion Guide for corrosion resistance properties. Refer to product brochure Assembly Instructions for Bondstrand fiberglass
flanges for bolt torque and installation information.
Table of Contents
ASME/ ANSI B16.5 & B16.47 A CL.150

Heavy-duty flanges ................................................................................................ 3
Loose-ring flanges ................................................................................................. 3
Blind flanges .......................................................................................................... 4
Orifice flanges......................................................................................................... 4
Common flange dimensions ................................................................................. 5
Stud bolt lengths .................................................................................................... 5
Nuts and washers................................................................................................... 6
ASME/ ANSI B16.5 A CL.300
Heavy-duty flanges................................................................................................. 6
Loose-ring flanges ................................................................................................. 7
Stud bolt lengths..................................................................................................... 8
ISO 7005 NP-10
Heavy-duty flanges................................................................................................. 8
Loose-ring flanges.................................................................................................. 9
Stud bolt lengths .................................................................................................. 10
Nuts and washers................................................................................................. 10
ISO 7005 NP-16
Heavy-duty flanges .............................................................................................. 11
Loose-ring flanges ............................................................................................... 11
Common flange dimensions ............................................................................... 12
Stud bolt lengths................................................................................................... 12
JIS B2220 5 kg/cm2
Stud bolt lenghts................................................................................................... 14
Nuts and washers................................................................................................. 15
JIS B2220 10 kg/cm2
Heavy-duty flanges............................................................................................... 15
Loose-ring flanges................................................................................................ 16
Stud bolt lenghts................................................................................................... 17
Nuts and washers................................................................................................. 15
JIS B2220 16 kg/cm2
Stud bolt lengths .................................................................................................. 19
Nuts and washers................................................................................................. 15
Seal ring dimensions............................................................................................ 19
Heavy-duty flanges ASME B16.5 & B16.47 A CL.150

Filament-wound heavy-duty flanges with integral Quick-lock (1 - 6 inch) or Taper/Taper (8 - 40 inch) socket end for adhesive bonding.
Size
Laying
Average
Part number
length
OL
weight
(inch)
(mm)
(mm)
(kg)
25
30
0.5
11215360A
11715360A
40
1.5
35
1.1
QQ215360A
QQ715360A
50
50
1.3
22215360A
22715360A
65
2.5
51
1.5
RR215360A
RR715360A
80
51
1.8
33215360A
33715360A
100
51
2.8
44215360A
44715360A
125
62
3.8
55215360A
55715360A
150
63
4.5
66215360A
66715360A
200
71
5.0
882153J8A
887153J8A
AA7153J8A
(mm)
(2000M)
(7000M)
250
10
86
9.5
AA2153J8A
300
12
100
10.5
BB2153J8A
BB7153J8A
350
14
108
21
CC2153J8A
CC7153J8A
400
16
118
27
DD2153J8A
DD7153J8A
450
18
122
32
EE2153J8A
EE7153J8A
500
20
135
40
FF2153J8A
FF7153J8A
550
22
160
49
GG2153J8A
GG7153J8A
600
24
186
58
HH2153J8A
HH7153J8A
650
26
186
66
JJ1953J8A
JJ6953J8A
700
28
186
73
KK1953J8A
KK6953J8A
750
30
186
88
LL1953J8A
LL6953J8A
800
32
186
112
ZZ1953J8A
ZZ6953J8A
900
36
211
116
MM1953J8A
MM6953J8A
1000
40
8
328
162
WW1953J8A
WW6953J8A
1. Bolt hole size and pattern also match those of ASME B16.1 class 125; ASME B16.24 class 150; ISO 2229 class 150 and
MSS SP-51 class 150LW.
2. ASME B16.47 A flange specification is for 26 (650mm) and above.
Loose-ring flange ASME B16.5 & B16.47 A CL. 150

Filament-wound loose ring (stub end) flanges with integral Quick-Lock (2 - 6 inch) or Taper/Taper
(8 - 40 inch) socket end for adhesive bonding.
Size
Laying
Overall
length
length
Flg thk
Stub
Average
length
weight
(LL)
(D)
(E)
(G)
Part number*
Stub end
Flange ring
(mm)
(inch)
(mm)
(mm)
(mm)
(mm)
(kg)
25
10
37
14.3
10
0.9
11215A60
(2000M)
11005687A
40
1.5
10
42
17.5
10
1.4
QQ215A60
QQ005687A
50
10
56
19
10
2.0
22215A60
22005687A
80
10
56
23.8
10
3.6
33215A60
33005687A
100
10
56
23.8
16
4.8
44215A60
44005687A
55005687A
125
10
67
23.8
16
5.4
55215A60
150
10
67
25.5
16
6.4
66215A60
66005687A
200
15
80
28.8
16
10.3
88212510
88005687A
250
10
15
95
35.6
23
16.0
AA212510
AA005687A
300
12
15
110
40
23
26
BB212510
BB005687A
350
14
15
115
41.6
27
36
CC212510
CC005687A
400
16
20
130
47.9
27
48
DD212510
DD005687A
450
18
20
134
50.2
35
56
EE212510
EE005687A
500
20
20
147
52
39
71
FF212510
FF005687A
600
24
20
198
63.7
47
108
HH212510
HH005687A
700
28
20
198
69
51
126
KK192510
KK005687A
750
30
20
198
71.6
46
146
LL192510
LL005687A
800
32
20
198
76.9
48
188
ZZ192510
ZZ005687A
900
36
20
223
85.4
53
238
MM192510
MM005687A
1000
40
20
340
86
63
340
WW192510
WW005687A
* For 7000M part number, replace 21 or 19 (3rd and 4th digit of stub end part number) with 71 or 69 respectively, e.g.
12 7000M stub end part number is BB712510.
Blind flanges ASME B16.5 & B16.47 A CL.150

Molded blind flanges.
Size
OL
Average
Part number
weight
(mm)
(inch)
(mm)
(kg)
(2000M)
(7000M)
25
25
0.4
11945700A
11C45700A
40
1.5
25
0.5
QQ945700A
QQC45700A
50
30
0.7
22945700A
22C45700A
80
30
1.1
33945700A
33C45700A
100
35
1.7
44935700A
44C35700A
125
35
2.6
55935700A
55C35700A
150
40
2.9
66935700A
66C35700A
200
45
5.2
88935700A
88C35700A
250
10
50
7.2
AA935700A
AAC35700A
300
12
60
11.4
BB935700A
BBC35700A
350
14
65
16.4
CC935700A
CCC35700A
400
16
70
23
DD935700A
DDC35700A
450
18
70
43
EE935700A
EEC35700A
500
20
70
51
FF935700A
FFC35700A
550
22
75
57
GG935700A
GGC35700A
600
24
85
85
HH935700A
HHC35700A
650
26
85
87
JJ935700A
JJC35700A
700
28
85
110
KK935700A
KKC35700A
750
30
90
132
LL935700A
LLC35700A
800
32
95
145
ZZ935700A
ZZC35700A
900
36
100
206
MM935700A
MMC35700A
Orifice flanges ASME B16.5 A CL.150

Filament-wound orifice flanges with integral Quick-Lock (2 - 6 inch) or Taper/Taper (8 - 16 inch) socket
end for adhesive bonding and inch or inch stainless steel 316 nipple and coupling.
Size
Laying
Overall
Average
length
length
weight
(LL)
(OL)
(mm)
(inch)
(mm)
(mm)
(kg)
(2000M)
(7000M)
50x15
2x0,5
40
86
2.2
2N215967A
2N715967A
50x20
2x0,75
40
86
2.2
2P215967A
2P715967A
80x15
3x0,5
39
85
3N215967A
3N715967A
80x20
3x0,75
39
85
3P215967A
3P715967A
100x15
4x0,5
39
85
4.7
4N215967A
4N715967A
100x20
4x0,75
39
85
4.7
4P215967A
4P715967A
150x15
6x0,5
40
97
6.9
6N215967A
6N715967A
150x20
6x0,75
40
97
6.9
6P215967A
6P715967A
200x15
8x0,5
55
120
7.4
8N2159J7A
8N7159J7A
200x20
8x0,75
55
120
7.4
8P2159J7A
8P7159J7A
250x15
10x0,5
55
135
13.5
AN2159J7A
AN7159J7A
250x20
10x0,75
55
135
13.5
AP2159J7A
AP7159J7A
300x15
12x0,5
55
150
21
BN2159J7A
BN7159J7A
300x20
12x0,75
55
150
21
BP2159J7A
BP7159J7A
350x15
14x0,5
55
155
27
CN2159J7A
CN7159J7A
350x20
14x0,75
55
155
27
CP2159J7A
CP7159J7A
400x15
16x0,5
55
165
35
DN2159J7A
DN7159J7A
400x20
16x0,75
55
165
35
DP2159J7A
DP7159J7A
Standard with SS 316 nipple and bushing. Other metals on request

2)
Also available with 2 outlets spaced at 180 degree
3)
Other flange drillings are available. Please consult NOV Fiber Glass Systems
1)
Part number
Common flange dimensions

Common dimensions for flanges with ASME B16.5/B16.47A class 150 drilling.
Size
OD
BCD
Bolt
Bolt
Bolt
hole
size
holes
(mm)
(inch)
(mm)
(mm)
(mm)
(inch)
25
108.0
79.4
15.9
0.5
40
1.5
127.0
98.4
15.9
0.5
50
152.4
120.7
19.1
0.625
80
190.5
152.4
19.1
0.625
100
228.6
190.5
19.1
0.625
125
254.0
215.9
22.2
0.75
150
279.4
241.3
22.2
0.75
200
342.9
298.5
22.2
0.75
250
10
406.4
362.0
25.4
0.875
12
300
12
482.6
431.8
25.4
0.875
12
350
14
533.4
476.3
28.6
12
400
16
596.6
539.8
28.6
16
450
18
635.0
577.9
31.8
1.125
16
500
20
698.5
635.0
31.8
1.125
20
550
22
749.3
692.2
34.9
1.25
20
600
24
812.8
749.3
34.9
1.25
20
650
26
870.0
806.5
34.9
1.25
24
700
28
927.1
863.6
34.9
1.25
28
750
30
984.3
914.4
34.9
1.25
28
800
32
1060.5
977.9
41.3
1.5
28
900
36
1168.4
1085.9
41.3
1.5
32
1000
40
1289.1
1200.2
41.3
1.5
36
Stud bolt lengths ASME B16.5 & B16.47 A CL.150

Recommended Stud bolt lengths for flanges with CL. 150 drilling.
Size
Heavy duty to
Heavy
Loose
duty
ring
Loose ring to
Steel
Loose
Steel
ring
(mm)
(inch)
(mm)
(mm)
(mm)
(mm)
(mm)
25
100
90
40
1.5
110
100
50
150
130
120
110
100
80
150
140
130
120
110
100
150
140
130
130
120
125
180
160
150
140
120
150
190
170
150
140
130
200
200
180
160
150
130
250
10
240
210
190
190
160
300
12
270
230
200
190
160
350
14
290
250
220
220
180
400
16
310
270
230
230
190
450
18
330
290
250
260
210
500
20
360
310
260
270
220
600
24
460
390
330
320
250
700
28
460
400
350
330
280
750
30
460
400
350
330
280
800
32
480
420
370
360
310
900
36
530
460
400
380
330
1000
40
760
580
520
400
350
Nuts and washers

Recommended nuts and washer sizes for flange with CL.150 & CL. 300 drilling.
Bolt
Nut
Washer
Washer
Size
Thickness
Thickness
OD
(inch)
(mm)
(mm)
(mm)
0.5
11
27
0.625
14
33
0.75
16
38
0.875
19
44
22
51
1.125
25
57
1.25
27
64
1.5
32
76
Heavy-duty flanges ASME B16.5 A CL.300
Filament-wound heavy-duty flanges with integral Quick-lock (1 - 6 inch) or Taper/Taper (8 - 24 inch)

socket end for adhesive bonding.
Size
Laying
OL
length
(mm)
Average
Part number
weight
(inch)
(mm)
(mm)
(kg)
(2000M)
(7000M)
25
30
0.5
11215360B
11715360B
40
1.5
35
1.1
QQ215360B
QQ715360B
50
50
1.3
22215360B
22715360B
80
51
1.8
33215360B
33715360B
100
51
2.8
44215360B
44715360B
125
62
3.4
55215360B
55715360B
150
63
4.5
66215360B
66715360B
200
71
5.0
882153J8B
887153J8B
250
10
86
9.5
AA2153J8B
AA7153J8B
300
12
100
14.5
BB2153J8B
BB7153J8B
350
14
108
21
CC2153J8B
CC7153J8B
400
16
118
27
DD2153J8B
DD7153J8B
450
18
122
32
EE2153J8B
EE7153J8B
500
20
135
40
FF2153J8B
FF7153J8B
600
24
186
58
HH2153J8B
HH7153J8B
Loose ring flanges ASME/ ANSI B16.5 A CL.300
Filament-wound loose ring (stub end) flanges with integral Quick-Lock (2 - 6 inch) Taper/Taper (8 - 24 inch) socket.
Size
Laying
Overall
length
length
Flg thk
Stub
Average
length
weight
Part number*
Stub end
Flange ring
(LL)
(D)
(E)
(G)
(mm)
(inch)
(mm)
(mm)
(mm)
(mm)
(kg)
50
10
56
22.2
10
2.7
22215A60
22005687B
80
10
56
28.6
10
5.2
33215A60
33005687B
100
10
56
31.7
16
7.6
44215A60
44005687B
125
10
67
34.9
16
10.5
55215A60
55005687B
150
10
67
36.5
16
13.4
66215A60
66005687B
200
15
80
41.3
16
20.0
88212510
88005687B
(2000M)
250
10
15
95
47.6
23
29.0
AA212510
AA005687B
300
12
15
110
50.8
23
42
BB212510
BB005687B
350
14
15
115
54
27
60
CC212510
CC005687B
400
16
20
130
58.2
27
76
DD212510
DD005687B
450
18
20
134
63.6
35
98
EE212510
EE005687B
500
20
20
147
66.5
39
117
FF212510
FF005687B
600
24
20
198
78.4
47
200
HH212510
HH005687B
* For 7000M part number, replace 21 or 19 (3rd and 4th digit of stub end part number) with 71 or 69 respectively, e.g. 12
7000M stub end p
art number is BB712510.

Common dimensions for flanges with ASME B16.5 class 300 drilling.
Size
OD
BCD
Bolt
(inch)
(mm)
(mm)
25
123.8
88.9
19.1
0.625
40
1.5
155.6
114.3
22.2
0.625
50
165.1
127.0
19.1
0.625
80
209.6
168.3
22.2
0.75
100
254.0
200.0
22.2
0.75
125
279.4
235.0
22.2
0.75
150
317.5
269.9
22.2
0.75
12
200
381.0
330.2
25.4
0.875
12
250
10
444.5
387.4
28.6
16
300
12
520.7
450.9
31.8
1.125
16
350
14
584.2
514.4
31.8
1.125
20
400
16
647.7
571.5
34.9
1.25
20
450
18
711.2
628.7
34.9
1.25
24
500
20
774.7
685.8
34.9
1.25
24
600
24
914.4
812.8
41.3
1.5
24
(mm)
Bolt
Bolt
hole
size
holes
(mm)
(inch)
Stud bolt lengths

Recommended stud bolt lengths for flanges with CL.300 drilling.
Size
Heavy duty to
Heavy
(mm)
(inch)
Loose
Loose ring to
Steel
Loose
Steel
duty
ring
(mm)
(mm)
(mm)
(mm)
ring
(mm)
25
110
100
40
1.5
120
100
50
150
140
130
120
110
80
160
150
140
130
120
100
160
160
140
150
140
125
180
170
160
160
150
150
190
180
160
170
150
200
210
200
180
180
170
250
10
240
230
210
220
190
300
12
280
250
230
230
200
350
14
300
270
240
250
220
400
16
320
290
260
260
230
450
18
330
310
270
290
250
500
20
360
330
290
300
260
600
24
470
410
360
350
300
Heavy-duty flange ISO 7005 PN-10

Size
Laying
OL
length
(mm)
Average
Part number
weight
(inch)
(mm)
(mm)
(kg)
(2000M)
(7000M)
25
30
0.5
11215360K
11715360K
40
1.5
35
1.1
QQ215360K
QQ715360K
50
50
1.3
22215360K
22715360K
80
51
1.8
33215360K
33715360K
100
51
2.8
44215360K
44715360K
125
62
3.6
55215360K
55715360K
150
63
4.5
66215360K
66715360K
200
71
5.0
882153J8K
887153J8K
250
10
86
9.5
AA2153J8K
AA7153J8K
300
12
100
14.5
BB2153J8K
BB7153J8K
350
14
108
21
CC2153J8K
CC7153J8K
400
16
118
27
DD2153J8K
DD7153J8K
450
18
122
32
EE2153J8K
EE7153J8K
500
20
135
40
FF2153J8K
FF7153J8K
600
24
186
58
HH2153J8K
HH7153J8K
700
28
186
73
KK1953J8K
KK6953J8K
750
30
186
88
LL1953J8K
LL6953J8K
800
32
186
112
ZZ1953J8K
ZZ6953J8K
900
36
211
116
MM1953J8K
MM6953J8K
1000
40
328
213
WW1953J8K
WW6953J8K
Loose-ring flanges ISO 7005 PN-10
Filament-wound loose ring (stub end) flanges with integral Quick-Lock (2 - 6 inch) or Taper/Taper (8 - 24 inch) socket.
Size
(mm)
(inch)
Laying
Overall
length
length
Flg thk
Stub
Average
length
weight
(LL)
(D)
(E)
(G)
(mm)
(mm)
(mm)
(mm)
Part number*
Stub end
(kg)
Flange ring
(2000M)
50
10
56
18
10
2.4
22215A60
22005687K
80
10
56
20
10
3.4
33215A60
33005687K
100
10
56
20
16
3.7
44215A60
44005687K
125
10
67
22
16
4.6
55215A60
55005687K
150
10
67
22
16
6.1
66215A60
66005687K
200
15
80
25
16
8.9
88212510
88005687K
250
10
15
95
28
23
11.8
AA212510
AA005687K
300
12
15
110
29
23
14.0
BB212510
BB005687K
350
14
15
115
36
27
25
CC212510
CC005687K
400
16
20
130
40
27
32
DD212510
DD005687K
450
18
20
134
42
35
38
EE212510
EE005687K
500
20
20
147
45
39
48
FF212510
FF005687K
600
24
20
198
52
47
73
HH212510
HH005687K
Note: For 7000M part number, replace 21 or 19 (3rd and 4th digit of stub end part number) with 71 or 69 respectively,
e.g. 12 7000M stub end part number is BB712510.

Common dimensions for flanges with ISO 7005 PN-10 drilling.
Size
(mm)
(inch)
OD
BCD
Bolt
Bolt
Bolt
hole
size
holes
(mm)
(mm)
(mm)
25
115
85
14
M12
40
1.5
150
110
18
M16
50
165
125
18
M16
80
200
160
18
M16
100
220
180
18
M16
125
250
210
18
M16
150
285
240
22
M20
200
340
295
22
M20
250
10
395
350
22
M20
12
300
12
445
400
22
M20
12
350
14
505
460
22
M20
16
400
16
565
515
26
M24
16
450
18
615
565
26
M24
20
500
20
670
620
26
M24
20
600
24
780
725
30
M27
20
700
28
895
840
30
M27
24
750
30
965
900
33
M30
24
800
32
1015
950
33
M30
24
900
36
1115
1050
33
M30
28
1000
40
1230
1160
36
M33
28
Stud bolt lengths

Recommended Stud bolt lenght for flanges with ISO 7005 PN-10 drilling.
Heavy duty to
Size
Heavy
Loose
Loose ring to
Steel
Loose
Steel
(mm)
(mm)
(mm)
duty
ring
(inch)
(mm)
(mm)
25
100
90
40
1.5
110
100
(mm)
ring
50
150
130
120
110
100
80
150
140
130
120
110
100
150
140
130
130
120
125
180
160
150
140
140
150
190
160
150
140
130
200
200
180
160
150
130
250
10
240
210
190
190
160
300
12
270
230
200
190
160
350
14
290
250
220
220
180
400
16
310
270
230
230
190
450
18
330
290
250
260
210
500
20
360
310
260
270
220
600
24
460
390
330
320
250
700
28
460
330
750
30
460
330
800
32
480
350
900
36
530
380
1000
40
770
460
Nuts and washers ISO 7005 PN-10 & PN-16

Recommended nut and washer sizes.
10
Bolt
Nut
Washer
Washer
Size
Thickness
Thickness
OD
(mm)
(mm)
(mm)
(mm)
M12
10
24
M16
13
30
M20
16
37
M24
19
44
M27
22
50
M30
24
56
M33
27
60
Heavy-duty flanges ISO 7005 PN-16

Size
Laying
OL
Average
length
Part number
weight
(mm)
(inch)
(mm)
(mm)
(kg)
(2000M)
(7000M)
25
30
0.5
11215360L
11715360L
40
1.5
35
1.0
QQ215360L
QQ715360L
50
50
1.3
22215360L
22715360L
80
51
2.3
33215360L
33715360L
100
51
2.5
44215360L
44715360L
125
62
3.5
55215360L
55715360L
150
63
4.5
66215360L
66715360L
200
71
6.5
882153J8L
887153J8L
250
10
86
9.2
AA2153J8L
AA7153J8L
300
12
100
12.0
BB2153J8L
BB7153J8L
350
14
108
20
CC2153J8L
CC7153J8L
400
16
118
32
DD2153J8L
DD7153J8L
450
18
122
33
EE2153J8L
EE7153J8L
500
20
135
43
FF2153J8L
FF7153J8L
600
24
186
65
HH2153J8L
HH7153J8L
Loose-ring flanges ISO 7005 PN-16
Filament-wound loose ring (stub end) flanges with integral Quick-Lock (2 - 6 inch) or Taper/Taper (8 - 24 inch) socket.
Size
Laying
Overall
Flg thk
Stub
Average
length
length
(LL)
(D)
(E)
length
(G)
weight
Part number*
Stub end
Flange ring
(2000M)
(mm)
(inch)
(mm)
(mm)
(mm)
(mm)
(kg)
50
10
56
18
10
2.4
22215A60
22005687L
80
10
56
20
10
3.4
33215A60
33005687L
100
10
56
20
16
3.7
44215A60
44005687L
125
10
67
22
16
4.8
55215A60
55005687L
150
10
67
23
16
6.3
66215A60
66005687L
200
15
80
27
16
9.1
88212510
88005687L
250
10
15
95
32
23
14.3
AA212510
AA005687L
300
12
15
110
35
23
18.7
BB212510
BB005687L
350
14
15
115
40
27
30
CC212510
CC005687L
400
16
20
130
44
27
39
DD212510
DD005687L
450
18
20
134
50
35
52
EE212510
EE005687L
500
20
20
147
54
39
73
FF212510
FF005687L
600
24
20
198
63
47
89
HH212510
HH005687L
11

Common dimensions for flanges with ISO 7005 PN-16 drilling.
Size
OD
BCD
Bolt
Bolt
Bolt
hole
size
holes
M12
(mm)
(inch)
(mm)
(mm)
(mm)
25
115
85
14
40
1.5
150
110
18
M16
50
165
125
18
M16
80
200
160
18
M16
100
220
180
18
M16
125
250
210
18
M16
150
285
240
22
M20
200
340
295
22
M20
12
250
10
405
355
26
M24
12
300
12
460
410
26
M24
12
350
14
520
470
26
M24
16
400
16
580
525
30
M27
16
450
18
640
585
30
M27
20
500
20
715
650
33
M30
20
600
24
840
770
36
M33
20
Stud bolt lenghts

Recommended stud bolt lengths for flanges with ISO 7005 PN-16 drilling.
Heavy duty to
Size
12
Heavy
Loose
Loose ring to
Steel
Loose
Steel
duty
ring
(mm)
(inch)
(mm)
(mm)
(mm)
(mm)
ring
(mm)
25
100
80
40
1.5
120
100
50
150
130
120
110
100
80
150
130
120
110
100
100
150
140
120
120
110
125
180
150
140
130
110
150
190
160
150
140
120
200
200
180
160
150
130
250
10
240
210
180
180
150
300
12
270
230
200
190
160
350
14
290
250
210
210
170
400
16
320
270
230
220
180
450
18
320
290
240
260
200
500
20
350
310
250
270
210
600
24
470
390
320
320
240
Heavy-duty flanges JIS B2220 5 kg/cm2

Size
Laying
OL
length
Average
Part number
weight
(mm)
(inch)
(mm)
(mm)
(kg)
(2000M)
(7000M)
25
30
0.5
11215360F
11715360F
40
1.5
35
1.1
QQ215360F
QQ715360F
50
50
1.3
22215360F
22715360F
80
51
1.8
33215360F
33715360F
100
51
2.8
44215360F
44715360F
125
62
3.5
55215360F
55715360F
150
63
4.5
66215360F
66715360F
200
71
5.0
882153J8F
887153J8F
250
10
86
9.5
AA2153J8F
AA7153J8F
300
12
100
14.5
BB2153J8F
BB7153J8F
350
14
108
21
CC2153J8F
CC7153J8F
400
16
118
27
DD2153J8F
DD7153J8F
450
18
122
32
EE2153J8F
EE7153J8F
500
20
135
40
FF2153J8F
FF7153J8F
550
22
160
49
GG2153J8F
GG7153J8F
600
24
186
58
HH2153J8F
HH7153J8F
650
26
186
66
JJ1953J8F
JJ6953J8F
700
28
186
73
KK1953J8F
KK6953J8F
750
30
186
88
LL1953J8F
LL6953J8F
900
36
211
116
MM1953J8F
MM6953J8F
1000
40
328
213
WW1953J8F
WW6953J8F
Loose-ring flanges JIS B2220 5 kg/cm2

Size
Laying
Overall
length
length
Flg thk
Stub
Average
length
weight
Part number*
Stub end
Flange ring
(LL)
(D)
(E)
(G)
(mm)
(inch)
(mm)
(mm)
(mm)
(mm)
(kg)
50
10
56
19
10
1.3
22215A60
22005687F
(2000M)
80
10
56
22
10
2.9
33215A60
33005687F
100
10
56
22
16
3.0
44215A60
44005687F
150
10
67
25
16
5.3
66215A60
66005687F
200
15
80
25
16
6.9
88212510
88005687F
250
10
15
95
29
23
10.8
AA212510
AA005687F
300
12
15
110
32
23
12.6
BB212510
BB005687F
350
14
15
115
38
27
20
CC212510
CC005687F
400
16
20
130
41
27
27
DD212510
DD005687F
450
18
20
134
44
35
38
EE212510
EE005687F
500
20
20
147
48
39
45
FF212510
FF005687F
600
24
20
198
54
47
71
HH212510
HH005687F
13

Common dimensions for flanges with JIS B2220 5 kg/cm2 drilling.
Size
OD
BCD
Bolt
Bolt
Bolt
hole
size
holes
(mm)
(inch)
(mm)
(mm)
25
95
75
(mm)
12
M10
40
1.5
120
95
15
M12
50
130
105
15
M12
80
180
145
19
M16
100
200
165
19
M16
125
235
200
19
M16
150
265
230
19
M16
200
320
280
23
M20
250
10
385
345
23
M20
12
300
12
430
390
23
M20
12
350
14
480
435
25
M22
12
400
16
540
495
25
M22
16
450
18
605
555
25
M22
16
500
20
655
605
25
M22
20
550
22
720
665
27
M24
20
600
24
770
715
27
M24
20
650
26
825
770
27
M24
24
700
28
875
820
27
M24
24
750
30
945
880
33
M30
24
900
36
1095
1030
33
M30
24
1000
40
1195
1130
33
M30
28
Stud bolt lengths

Recommended stud bolt lengths for flanges with JIS B2220 5 kg/cm2 drilling.
Size
(mm)
14
Heavy duty to
(inch)
Loose ring to
Heavy
Loose
duty
ring
Steel
Loose
Steel
(mm)
(mm)
(mm)
(mm)
(mm)
ring
25
90
70
40
1.5
110
90
50
140
120
110
100
90
80
150
130
120
120
100
100
150
140
120
130
110
125
180
130
150
180
160
140
140
110
200
200
170
150
140
120
250
10
230
200
170
170
140
300
12
260
220
180
170
140
350
14
290
240
200
200
160
400
16
310
260
210
210
160
450
18
310
270
220
230
170
500
20
340
290
230
240
180
600
24
450
370
290
280
210
700
28
450
300
750
30
460
310
900
36
510
340
1000
40
750
490
Nuts & washer

Recommended nuts and washer sizes for flanges with JIS B2220 5, 10 and 16 kg/cm2 drilling.
Bolt
Nut
Washer
Washer
Size
thickness
thickness
OD
(mm)
(inch)
(mm)
(mm)
M10
21
M12
10
2.5
24
M16
13
30
M20
16
37
M22
18
39
M24
19
44
M27
22
50
M30
24
56
M33
27
60
M36
29
66

Filament-wound heavy-duty flanges with integral Quick-Lock (1 - 6 inch) or Taper/Taper (8 - 40 inch)
Size
Laying
OL
length
Average
Part number
weight
(mm)
(inch)
(mm)
(mm)
(kg)
(2000M)
(7000M)
25
30
0.4
11215360G
11715360G
40
1.5
35
0.6
QQ215360G
QQ715360G
50
50
0.9
22215360G
22715360G
80
51
1.8
33215360G
33715360G
100
51
2.2
44215360G
44715360G
125
62
3.5
55215360G
55715360G
150
63
4.1
66215360G
66715360G
200
71
5.5
882153J8G
887153J8G
250
10
86
8.7
AA2153J8G
AA7153J8G
300
12
100
10.0
BB2153J8G
BB7153J8G
350
14
108
12.0
CC2153J8G
CC7153J8G
400
16
118
18.0
DD2153J8G
DD7153J8G
450
18
122
23
EE2153J8G
EE7153J8G
500
20
135
29
FF2153J8G
FF7153J8G
600
24
186
47
HH2153J8G
HH7153J8G
650
26
186
66
JJ1953J8G
JJ6953J8G
700
28
186
73
KK1953J8G
KK6953J8G
750
30
186
80
LL1953J8G
LL6953J8G
900
36
211
95
MM1953J8G
MM6953J8G
1000
40
328
213
WW1953J8G
WW6953J8G
15

Size
(mm)
Laying
Overall
length
length
(inch)
Flg thk
Stub
Average
length
weight
(LL)
(D)
(E)
(G)
(mm)
(mm)
(mm)
(mm)
Part number*
Stub end
(kg)
Flange ring
(2000M)
50
10
56
19
10
2.1
22215A60
22005687G
80
10
56
22
10
2.9
33215A60
33005687G
100
10
56
22
16
3.4
44215A60
44005687G
150
10
67
25
16
6.4
66215A60
66005687G
200
15
80
25
16
7.5
88212510
88005687G
250
10
15
95
29
23
12.7
AA212510
AA005687G
300
12
15
110
32
23
14.8
BB212510
BB005687G
350
14
15
115
38
27
22
CC212510
CC005687G
400
16
20
130
41
27
32
DD212510
DD005687G
450
18
20
134
44
35
41
EE212510
EE005687G
500
20
20
147
48
39
52
FF212510
FF005687G
600
24
20
198
54
47
81
HH212510
HH005687G

Size
(mm)
16
(inch)
OD
BCD
Bolt
Bolt
Bolt
hole
size
holes
(mm)
(mm)
(mm)
25
125
90
19
M16
40
1.5
140
105
19
M16
50
155
120
19
M16
80
185
150
19
M16
100
210
175
19
M16
125
250
210
23
M20
150
280
240
23
M20
200
330
290
23
M20
12
250
10
400
355
25
M22
12
300
12
445
400
25
M22
16
350
14
490
445
25
M22
16
400
16
560
510
27
M24
16
450
18
620
565
27
M24
20
500
20
675
620
27
M24
20
600
24
795
730
33
M30
24
650
26
845
780
33
M30
24
700
28
905
840
33
M30
24
750
30
970
900
33
M30
24
900
36
1120
1050
33
M30
28
1000
40
1235
1160
39
M36
28
Stud bolt lengths

Size
Heavy duty to
Heavy
(mm)
(inch)
Loose ring to
Loose
duty
ring
(mm)
(mm)
Steel
Loose
Steel
(mm)
(mm)
(mm)
ring
25
110
90
40
1.5
120
100
50
150
130
120
110
100
80
150
130
120
120
100
100
150
140
120
130
110
125
180
140
150
190
160
150
140
120
200
200
170
150
140
120
250
10
240
200
180
170
140
300
12
270
220
190
170
140
350
14
290
240
200
200
160
400
16
310
260
220
210
170
450
18
320
270
230
230
180
500
20
340
290
240
250
190
600
24
460
380
310
290
220
700
28
460
310
750
30
460
310
900
36
510
340
1000
40
750
460

Size
Laying
OL
length
(mm)
Average
Part number
weight
(inch)
(mm)
(mm)
(kg)
(2000M)
(7000M)
25
30
0.5
11215360H
11715360H
40
1.5
35
1.1
QQ215360H
QQ715360H
50
50
1.3
22215360H
22715360H
80
51
1.8
33215360H
33715360H
100
51
2.8
44215360H
44715360H
125
62
3.5
55215360H
55715360H
150
63
4.5
66215360H
66715360H
200
71
5.0
882153J8H
887153J8H
250
10
86
9.5
AA2153J8H
AA7153J8H
300
12
100
14.5
BB2153J8H
BB7153J8H
350
14
108
21
CC2153J8H
CC7153J8H
400
16
118
27
DD2153J8H
DD7153J8H
450
18
122
32
EE2153J8H
EE7153J8H
500
20
135
40
FF2153J8H
FF7153J8H
600
24
186
58
HH2153J8H
HH7153J8H
17

Size
(mm)
Laying
Overall
length
length
(inch)
Flg thk
Stub
Average
length
weight
(LL)
(D)
(E)
(G)
(mm)
(mm)
(mm)
(mm)
Part number*
Stub end
Flange ring
(2000M)
(kg)
50
10
56
19
10
2.0
22215A60
22005687H
80
10
56
22
10
3.5
33215A60
33005687H
100
10
56
22
16
4.1
44215A60
44005687H
150
10
67
25
16
8.1
66215A60
66005687H
200
15
80
25
16
9.5
88212510
88005687H
250
10
15
95
29
23
17.0
AA212510
AA005687H
300
12
15
110
32
23
21
BB212510
BB005687H
350
14
15
115
41
27
33
CC212510
CC005687H
400
16
20
130
48
27
44
DD212510
DD005687H

Size
18
OD
BCD
Bolt
Bolt
Bolt
hole
size
holes
M16
(mm)
(inch)
(mm)
(mm)
(mm)
25
125
90
19
40
1.5
140
105
19
M16
50
155
120
19
M16
80
200
160
23
M20
100
225
185
23
M20
125
270
225
25
M22
150
305
260
25
M22
12
200
350
305
25
M22
12
250
10
430
380
27
M24
12
300
12
480
430
27
M24
16
350
14
540
480
33
M30
16
400
16
605
540
33
M30
16
450
18
675
605
33
M30
20
500
20
730
660
33
M30
20
600
24
845
770
39
M36
24
Stud bolt lengths

Size
Heavy duty to
Heavy
(mm)
(inch)
Loose ring to
Loose
Steel
Loose
Steel
duty
ring
(mm)
(mm)
(mm)
(mm)
ring
(mm)
25
110
90
40
1.5
120
10
100
50
150
130
120
110
80
160
140
130
120
110
100
160
150
130
130
120
125
180
150
150
190
170
150
150
130
200
210
180
160
150
130
250
10
240
210
180
170
150
300
12
270
220
200
180
150
350
14
300
260
230
220
190
400
16
320
280
240
230
200
450
18
330
250
500
20
350
260
600
24
460
330
Seal ring dimensions

Reference seal ring dimensions for Quick-Lock and Taper/Taper flanges.
Size
S1
S2
S3
S4
W1
W2
Y1
Y2
(inch)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
25
33.9
100.8
4.5
0.9
0.6
40
1.5
47.1
119.4
4.5
0.9
0.6
50
73.4
91.4
144.1
2.4
2.4
0.9
0.5
80
89.5
104.9
120.7
178.3
2.4
2.4
0.9
0.5
100
111.8
134.3
158.1
216.0
2.5
2.5
1.1
0.6
125
140.5
159.5
178.5
244.5
2.5
2.5
1.1
0.6
150
167.5
186.4
205.5
268.8
2.5
2.5
1.1
0.6
200
219.5
239.5
259.5
331.5
2.8
2.8
1.5
1.0
250
10
272.5
292.5
312.5
395.5
2.8
2.8
1.5
1.0
300
12
323.5
344.4
368.5
462.5
2.8
2.8
1.5
1.0
350
14
355.3
376.0
396.6
495.3
2.8
2.8
1.5
1.0
400
16
403.1
430.9
458.7
582.5
2.8
2.8
1.5
1.0
450
18
453.4
482.6
511.8
603.2
3.9
3.9
1.5
1.0
500
20
504.4
533.7
562.9
658.1
3.9
3.9
1.5
1.0
550
22
558.5
586.0
613.4
727.6
5.4
5.4
1.5
1.0
600
24
609.3
636.5
663.7
765.2
5.4
5.4
1.5
1.0
650
26
661.7
687.8
714.0
820.5
5.4
5.4
1.5
1.0
700
28
711.2
737.6
764.0
859.5
5.4
5.4
1.5
1.0
750
30
763.5
788.4
814.3
948.2
5.4
5.4
1.5
1.0
800
32
807.5
834.4
860.3
994.7
5.4
5.4
1.5
1.0
900
36
918.0
949.2
982.5
1100.9
6.5
6.5
1.5
1.0
1000
40
1057.5
1098.5
1139.5
1251.8
6.5
6.5
1.5
1.0
(mm)
19
National Oilwell Varco has produced this brochure for general information only,
and it is not intended for design purposes. Although every effort has been made to
maintain the accuracy and reliability of its contents, National Oilwell Varco in no way
assumes responsibility for liability for any loss, damage or injury resulting from the use
of information and data herein. All applications for the material described are at the
users risk and are the users responsibility.
All brands listed are trademarks of National Oilwell Varco.
North America
17115 San Pedro Avenue
Suite 200
San Antonio, TX 78232 USA
Phone: +1 210 477 7500
South America
Estrada de Acesso Zona
Industrial Porturia de Suape, s/no.
Recife, PE, Brazil 55.590-000
Phone: +55 81 3501 0023
Europe
P.O. Box 6, 4190 CA
Geldermalsen, The Netherlands
Phone: +31 345 587 587
Asia Pacific
No. 7A, Tuas Avenue 3
Jurong, Singapore 639407
Phone: +65 6861 6118
Middle East
P.O. Box 17324
Dubai, UAE
Phone: +971 4881 3566
www.fgspipe.com [email protected]
2012 National Oilwell Varco. All rights reserved.

MOS2010 supersedes FP 168 E - October 2012
Marine & Offshore

BONDSTRAND 2000M & 7000M
Glassfibre Reinforced Epoxy (GRE)
Flanges & Pipe Systems
1 to 6 inch (Quick-lock joint), 8 to 40 inch
(Taper/Taper joint) with external pressure requirements
Pipex px are the sole

distributor for NOV FGS in
the UK and Ireland
T: +44 (0) 1752 581200

F: +44 (0) 1752 581209
[email protected]
www.pipexpx.com

Flanges Pipe Systems

Uploaded by

Copyright:

Available Formats

Flanges Pipe Systems

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Flanges Pipe Systems

Uploaded by

Copyright:

Available Formats

Marine & Offshore

BONDSTRAND 2000M & 7000M

Pipex px are the sole

T: +44 (0) 1752 581200

Bondstrand 2000M/7000M for marine

Uses and applications

Portable discharge line

Quick-Lock adhesive-bonded joint

Taper/Taper adhesive-bonded joint

Pipe series .............................................................................................................

Joining system and configuration .........................................................................

Typical Pipe length ................................................................................................

Typical Pipe dimensions and weights ...................................................................

Ultimate Collapse Pressures .............................................................................

Joint dimensions Quick-Lock .............................................................................

Joint dimensions Taper/Taper................................................................................

Span length .......................................................................................................

Elbows ............................................................................................................... 9-10

Reducers (Concentric, Eccentric)......................................................................... 19-20

Support Saddles ...................................................................................................

Grounding Saddles ...............................................................................................

Assembly of double O-ring expansion joint ..........................................................

Expansion coupling ...............................................................................................

Engineering design & installation data .................................................................

Field testing ...........................................................................................................

Joining system &

Typical pipe length

Approximate overall Length

Typical pipe dimensions

Ultimate collapse pressure (ultimate short term external failure pressure) at 65 C.

Dimensions for Quick-Lock bell & spigot adhesive bonded joints.

Insertion Spigot Diameter Spigot Length

Filament-wound 90 elbows with integral Quick-Lock (1-6 inch) or T

Overall Max. Working

Quick-Lock Filament wound

Taper/Taper Filament wound

Overall Maximum Average

Reducing Tees (cont)

Quick-Lock Filament wound

Taper/Taper Filament wound

Overall Maximum Average

Reducing Tees (cont)

Quick-Lock Filament wound

Taper/Taper Filament wound

Overall Maximum Average

Reducing Tees (cont)

Quick-Lock Filament wound

Taper/Taper Filament wound

Overall Maximum Average

Filament-wound concentric reducers with integral Quick-Lock (1-6 inch) or Taper/Taper

Filament-wound Eccentric Reducers with integral Quick-Lock (1-6 inch) or Taper/Taper

* Remaining gap after bonding.

Filament-wound pipe saddles for wear, support and anchor.

Filament-wound pipe saddles for grounding in conductive piping systems.

Filament-wound bell mouths with adhesive-bonded HD-flange.

* Weights provided are for bell mouth with CL150 flange.

Key-Lock Adapter for

Double O-ring Adapter

Number of Adhesive Kits per joint.

Engineering design &