DATAsheet >

NOV
2004

HOT-WEATHER Concreting

>

INTRODUCTION
While hot weather conditions are commonly
encountered in summer, combinations of high
temperatures, winds and low humidity could result
in conditions leading to problems with concrete
placement and finishing at any time.
This data sheet provides guidance on the effects
of hot weather conditions on the properties of
concrete, and the precautions that should be taken,
particularly with flatwork, to minimize any potential
adverse effects when placing concrete under these
conditions.

E = 5([Tc + 18]2.5 r[Ta + 18]2.5)(V + 4) x 10-6

where
E = evaporation rate, kg/m2/h
r = relative humidity/100
Ta = air temperature, C
Tc = concrete (water surface) temperature, C
V = wind velocity, km/h.

>

WHAT IS HOT WEATHER?

For the purposes of this data sheet, hot weather is
any combination of:
high ambient temperature;
low relative humidity;
high wind speed.
AS 13791 places a 35C limit on the maximum
concrete temperature at the time of delivery.
However, when the air temperature rises above
30C, it is usually recommended that precautions
be taken, particularly if there is also hot dry wind.
This is firstly to ensure an acceptable concrete
temperature at the point of delivery, and secondly to
avoid problems with plastic shrinkage cracking and
premature stiffening of the concrete.

Figure 1 can be used to estimate the possibility

of plastic shrinkage cracking occurring, and hence
the need for suitable precautions to be taken. This
nomograph is used to combine the effects of air
temperature, relative humidity, concrete temperature
and wind speed, to estimate the rate at which water
will evaporate from the surface of the concrete. As a
general rule, if the rate of evaporation is greater
than 1 kg of water per square metre of concrete per
hour (1 kg/m2/h), then precautions against
premature drying and plastic shrinkage cracking
should be taken.
Alternatively, the rate of evaporation can be
calculated from the following equation:

COMBINATIONS of high temperatures,

winds and low humidity could result in
conditions leading to problems with
concrete placement and finishing.

RELATIVE HUMIDITY (%) = 100

35

40 = CONCRETE TEMPERATURE (C)

90
80
30
70
60
50
40
30
20
10

5
10
15
AIR TEMPERATURE (C)

20

25

30

25
20
15
10
5

35
4.5

WIND SPEED (km/h) = 40

35

4.0

30

3.5
USE OF CHART:
1 From air temperature
move UP to relative humidity.
2 Move RIGHT to concrete temperature.
3 Move DOWN to wind speed.

3.0

25

2.5

20

2.0

15

1.5

10

1.0

0.5

4 Move LEFT to read rate of evaporation.

NOTE: Evaporation rates approaching

1.0 kg/m2/h are likely to necessitate
precautions against premature drying

0
RATE OF WATER EVAPORATION (kg/m2/h)

Figure 1: Effect of concrete and air temperatures, relative humidity and wind velocity on the rate of
evaporation of surface moisture from concrete (after ACI 305 2)

INITIAL SETTING TIME (hours)

8

SLUMP (mm)
120

100

6
80

5
4

60

40

2
20

1
0

0
10
15
20
5
AMBIENT AIR TEMPERATURE (C)

25

30

Figure 2: Influence of air temperature on setting

times of concrete made with Type GP cement

Page 2 of 7 > HOT-WEATHER Concreting

35

10
20
30
0
FRESH CONCRETE TEMPERATURE (C)

40

Figure 3: Decrease in workability of fresh concrete

(as measured by slump), made with constant water
content, as temperature increases

50

% OF 28-DAY COMPRESSIVE STRENGTH OF CONCRETE CURED AT 23C

140
120

23C
100

Concrete temperature Hot weather conditions

may accentuate the temperature rise in concrete
caused by the heat of hydration. In large sections
thermal gradients through the element may
cause thermal cracking. Laboratory tests show
that sustained higher temperatures significantly
influence the compressive strength gain of
hardened concrete Figure 4. While increased
concrete temperatures may result in an increase
in the early rate of strength gain, in the longer
term, concrete cured at lower temperatures will
achieve higher ultimate strength.

Poor surface appearance With the increased

rate of evaporation, the surface of the concrete
will dry out and stiffen. In the case of flatwork
this may lead to premature finishing of the
surface, trapping an amount of bleed water
within the mix. The compacted surface layer
(from finishing) may cause the rising bleed water
to be trapped below the surface, resulting in
debonding of the surface layer and subsequent
flaking. Also, colour differences on the surface
may result from different rates of hydration and
cooling effects.

Plastic shrinkage cracking Hot weather

conditions accelerate the loss of moisture from
the surface. If the rate of evaporation is greater
than the rate of bleeding (rate at which water
rises to the surface), surface drying will occur,
resulting in shrinkage of the concrete. When the
shrinkage stresses exceed the tensile capacity
of the concrete, cracking will occur. The
likelihood of plastic shrinkage cracking is
therefore greater whenever hot weather
conditions increase evaporation or the concrete
has a reduced bleeding rate. Plastic shrinkage
cracks can be quite deep, as the plastic concrete
has little capacity to resist shrinkage stresses,
and cracks continue to widen and propagate
until the shrinkage stresses are relieved. (Note
plastic shrinkage cracks seldom extend to free
edges, as unrestrained contraction of the
concrete is possible at these locations.)

Thermal cracking Concrete is at risk of thermal

cracking when it is first placed, and the heat of
hydration raises the temperature of the interior
of the concrete. Rapid changes in the
temperature of the external concrete surface,
such as when concrete slabs, walls or pavements
are placed on a hot day followed by a cool night,
lead to thermal gradients between the warm/hot
interior and the colder external surface. The
warmer interior provides a restraint to the
colder external surface, which wants to contract.

30C
40C
50C

80
60
40
20

Specimens moist-cured at temperature indicated,

for first 28 days, then moist-cured at 23C thereafter

0
1
3
AGE (days)

28

90

365

Figure 4: Effect of high curing temperatures on

concrete compressive strength

EFFECTS OF HOT WEATHER CONDITIONS

Most of the problems associated with placing
concrete in hot weather conditions relate to the
increased rate of cement hydration at higher
temperatures and the increased rate of evaporation
of moisture from the fresh concrete.
The properties of concrete that may be affected
by hot weather conditions include:

Setting time As the concrete temperature

increases, the setting time, and thus the time to
place, compact and finish the concrete is
reduced Figure 2.

Workability and slump Higher temperatures

reduce the workability (or slump) of the
concrete more rapidly with time Figure 3.
Adding more water to improve the workability of
the mix decreases the strength and increases
the permeability, and ultimately affects the
durability of the concrete.

Compressive strength Higher water demand

and higher concrete temperature could lead to
reduced 28-day strengths. If more water is added
to the concrete mix at higher temperatures to
maintain or restore workability, the watercement ratio will be increased, resulting in a
loss of both potential strength and durability.
This may also increase the drying shrinkage of
the hardened concrete. Where water is not
added, the reduced setting time and workability
increase the potential for inadequate compaction
(itself of a major influence on strength), the
formation of cold joints and poor finishes.

Page 3 of 7 > HOT-WEATHER Concreting

Depending on the temperature differential,

cracking of the concrete may result. Massive or
thick concrete elements are more at risk
because of the insulating effect that the concrete
provides to the interior of the element.
MINIMISING THE EFFECTS OF HOT WEATHER
CONDITIONS
Control concrete temperature AS 1379 requires
that concrete temperatures at the point of
delivery be within the range 5C to 35C. For
high ambient temperatures, precautions need to
be taken by the supplier to ensure that the
concrete temperature at the point of delivery is
within the allowable range.
There are a number of options to control the
temperature of concrete, including adjusting the
temperature of the ingredients and/or cooling of
the concrete mix. The sensitivity of the
temperature of a normal concrete mixture to
that of its components can be demonstrated by
the following formula:

Admixtures Various types of chemical

admixtures can be beneficial in hot weather
conditions. Water reducers (plasticisers) can be
used to reduce the water content or to aid the
workability. This enables rapid placement and
consolidation of the concrete with beneficial
effects on the ultimate strength and durability.
Set-retarders can provide additional time to
place and finish flatwork. With rapid drying of
the surface, caution is required with the use of
set retarders, as the surface may appear ready
for finishing, but the concrete below may still be
plastic from the retarder, leading to a spongy
feel under foot. This could affect the uniformity
of the surface finish.

Cement type Selection of a particular cement

type may provide additional benefits. Using
slower hydration cements (eg Type LH) with
lower rate of heat development can provide
extra time for placing and finishing, reduce the
concrete temperature and the risk of thermal
cracking upon cooling of the concrete.

Cement content The temperature increase

from hydration of cement in a given concrete is
proportional to its cement content. The cement
content therefore should be limited to that
required to provide strength and durability.

T = 0.1 Tc + 0.6Ta + 0.3Tw

where
T = concrete temperature
Tc = temperature of the cement
Ta = temperature of the aggregate
Tw = temperature of the water.
Because aggregates make up the bulk of the
concrete, and also have the highest heat
capacity, they have the greatest effect on the
temperature of the freshly mixed concrete.
Unfortunately the temperature of the
aggregates is also the most difficult to control.
Some benefit can be gained from shading
stockpiles from the sun and/or keeping them
moist with sprinklers. Storage in bins (painted
white) will also assist.
The mix water offers the most potential for
temperature reduction, particularly by adding
crushed ice to it, as the latent heat of the ice is
considerably higher than that of water.
The temperature of the cement does not usually
contribute significantly to the temperature of
freshly mixed concrete because of its low specific
heat and relatively small mass in the mix.
Liquid nitrogen, injected into the concrete while
mixing, may also be utilised. Latent thermal
energy on vaporisation to gas cools the concrete
dramatically without any known deleterious
effect. It should be noted that this process is
usually economical only on major projects
involving construction of large concrete elements.
Page 4 of 7 > HOT-WEATHER Concreting

PRECAUTIONS IN HOT WEATHER CONDITIONS

General Problems usually arise when site
personnel are not aware of the effect of weather
conditions and/or weather conditions change
during the placing and/or finishing of the
concrete. Improvised responses to unexpected
changes is not recommended as the damage
that can result from uncontrolled effects of hot
weather conditions may never be completely
alleviated.
The first option to be considered in hot, adverse
weather conditions is whether or not to
postpone the placement of concrete. It is often
better to wait than risk costly repairs (or even
replacement) of defective work and dissatisfied
clients seeking compensation. If work is to
proceed, proper planning from careful selection
of materials to procedures for hot weather work
is essential if the associated risks are to be
minimised.

Planning A successful, well-run, hot-weather

project is the result of thorough and careful
planning. Planning for hot weather conditions is
essential because of the potential effects on
fresh and recently placed concrete. For plastic

concrete these include increased water demand

and risk of plastic shrinkage cracking, greater
slump loss, faster setting and difficulty in
controlling entrained air content; for hardened
concrete they include reduced strength and
durability, and increased drying shrinkage.
While the designer or specifier may control
some items on the following list, it may not
always be possible to anticipate just when and
under what weather conditions the work will be
carried out. Therefore the builders and
sub-contractors should also be aware/alert to
all of the possibilities.

Where hot weather conditions are likely to

present a problem, consult the concrete
supplier as early as possible.

Have standby equipment and manpower for

all stages.

Use the largest size and amount of coarse

aggregate compatible with the job. This also
helps minimise the tendency of the concrete
to crack.

In determining the slumps of the concrete to

be used, consider the effects of hot weather
on the ability to place and finish the concrete.

Programme concreting for the cooler parts

of the day, or even schedule night-time
placement if possible.

Specify the maximum acceptable delivery

temperature of the concrete so that the
supplier can plan to cool the materials as
needed.

Avoid delays at all stages.

Plan the locations of construction joints

ahead of time with hot weather contingencies
in mind.

Consider spacing contraction (control) joints

at slightly smaller intervals than when
concreting at lower temperatures.

Use sunshades or windbreaks.

Delay construction of indoor slabs on grade

until the walls are up and the roof is on.

Pay attention to the rate of concrete

placement. Be ready to notify the concrete
supplier promptly of any changes in schedule,
which may become needed as the job
progresses.

Keep an evaporative retarder (aliphatic

alcohol) on site in case conditions require
its use.

Page 5 of 7 > HOT-WEATHER Concreting

Concrete Production The concrete suppliers

responsibility is to manufacture and deliver the
concrete in accordance with AS 1379. The
following methods can be used by the supplier to
assist with the placing of concrete in hot weather:

Shade stockpiles, sprinkle aggregates ahead

of time for evaporative cooling, or cool them
by other means.

Paint the mixer and storage bins white to

minimise absorption of heat from the sun.

Use ice as part of the mix water or cool the

concrete with liquid nitrogen.

Delivery and Discharge Delays in delivery can

undo the best mixing practices. The concrete
supplier should set up and maintain a good
delay-free schedule for delivering the concrete
to the required location on the site.

Minimise transport time and avoid

unnecessary delays.

Avoid prolonged mixing. Transit mixer trucks

should be discharged as soon as possible
after the water has been added to the mix.

For large projects, consider batching and

mixing the materials using a job-site plant.

Water should not be added to pre-mixed

concrete at the job site unless it is part of the
amount required initially for the specified
maximum water-cement ratio and the
specified slump.

Placing and Finishing For successful placing

and finishing it is necessary to provide an
environment in which workers and equipment
can function well, and concrete can be adequately
protected from rapid warming and/or drying.

Schedule placement for the cool time of the

day such as early morning or late afternoon.
On some jobs, concreting at night (if
permitted) may be more advantageous.

Have all forms, equipment and workers

ready to receive and handle concrete,
especially the first delivery.

Use sunshades and/or windbreaks.

Keep all equipment that touches the

concrete cool (chutes, conveyors, pump
lines, tremies, reinforcement and buggies).
Protecting equipment from the direct sun
will assist. If it cant be kept continuously
cool, spray-cool it as necessary with water.

For a slab without a vapour barrier under it,

dampen the sub-grade before placing
concrete.

Use cool water to dampen side forms for

slabs or walls.

Aliphatic alcohols have an average coverage of

60 to 80 m2 per litre. Because the dilution rate
varies depending on the specific product, the
application rate should always be in accordance
with the manufacturers specifications.
In adverse or severe weather conditions, or in
situations where the surface is worked (or the
coverage is otherwise broken), the aliphatic
alcohol may need to be re-applied to maintain an
effective cover (ie after bullfloating, trowelling
and other surface floating). In extreme conditions
there may be a requirement for 5 to 6 or more
applications to prevent the rapid drying of the
surface while the concrete sets and bleed water
dissipates.
Most aliphatic alcohols contain a fugitive dye to
assist the monitoring of coverage. The dye has no
effect on the strength or colour of the concrete.

Use a thermometer to monitor the

temperature at which concrete is being
delivered, and call for adjustments at the
plant if necessary.
Expect concrete to set more rapidly and have
a shorter finishing time.
Ensure that slabs have a minimum front to
which fresh batches of concrete are added.
Perform all operations rapidly, but dont
finish slabs prematurely, eg while bleed
water is still on the surface.

Evaporation Control Protect the surface of

concrete slabs at all stages against excessive
evaporation and premature drying out by using
an evaporative retarder such as aliphatic
alcohol. Aliphatic alcohols are applied to the
freshly placed and screeded concrete surface,
where they form a chemical film which reduces
the rate at which water evaporates from the
surface of the concrete. By controlling the
premature drying out of the surface layer of
concrete, the tendency for the concrete to shrink
and for plastic shrinkage cracking to occur is
reduced or eliminated.
The benefits of using aliphatic alcohols on the
concrete surface can be manifested in many
ways as listed below. These benefits are usually
realised with no effect on the cement hydration
and/or setting time of the concrete.

Improves surface workability and thereby

increases project and labour productivity.

Improves surface finishing, and in turn

durability, abrasion resistance and
resistance to the ingress of water-borne
contaminants.

Assists in eliminating the damaging practice

of wet wiping or spraying water onto the dry
patches during trowelling of the concrete,
and thus helps to prevent surface dusting
problems.

Significantly reduces surface crusting.

Surface crusting can cause problems with
cracking, particularly with stamped concrete
finishes.

Reduces the risk of premature surface

finishing by allowing the concrete to
properly set. A dry surface layer may appear
to indicate that the concrete has set, but can
lead to a spongy concrete effect, as the
concrete below is still plastic. This may result
in flaking and an uneven surface finish.

Virtually eliminates differential surface

drying.

Page 6 of 7 > HOT-WEATHER Concreting

Curing and Protection It is essential that all

surfaces be kept continuously moist by curing
the concrete, since drying, even intermittently,
can produce drying shrinkage and/or crazing
type cracking on the concrete surface.

Curing should commence immediately after

the slab has been finished, and is particularly
important during the first day after
placement, and in hot or windy conditions.

Curing methods include ponding with water,

use of wet hessian or cotton mats,
continuous spray mist, covering with plastic
sheeting or sprayed on curing compounds.

When forms are removed, curing should be

provided to the newly exposed surfaces.

Some means of water curing is advantageous

in hot weather as the water also assists in
cooling the concrete while it hardens and
gains strength. Care is required, however, as
the surface needs to be sufficiently hard
before water curing can be undertaken
without risk of surface damage. This may
leave the surface exposed to drying and
possible cracking between completion of the
finishing and commencement of the curing.

Note that aliphatic alcohols are NOT curing

compounds and should not be specified or
used as a substitute for them. Aliphatic
alcohols are used between the initial
screeding and final finishing operations, and
adequate curing of the concrete must still be
provided once final finishing has been
completed. While aliphatic alcohols are
compatible with most curing compounds,
this should be checked if products are
purchased from different manufacturers.

CCAA OFFICES
SYDNEY OFFICE:

NOV
2004

Level 6, 504 Pacific Highway

St Leonards NSW Australia 2065
POSTAL ADDRESS:

REFERENCES
1 AS 1379 Manufacture and supply of concrete
Standards Australia 1997
2 ACI Committee 305, Hot Weather Concreting
ACI Manual of Concrete Practice Part 2:
Construction practices and inspection,
pavements American Concrete Institute,
Farmington Hills, USA, 1999.
This data sheet replaces:
Technical Bulletin 95/2 Hot Weather Concreting
previously published by the Australian Pre-Mixed
Concrete Association.

Locked Bag 2010

St Leonards NSW 1590
TELEPHONE: (61 2) 9437 9711
FACSIMILE: (61 2) 9437 9470
BRISBANE OFFICE:

Level 14, IBM Building

348 Edward Street
Brisbane QLD 4000
TELEPHONE: (61 7) 3831 3288
FACSIMILE: (61 7) 3839 6005
EXTRACTIVE INDUSTRIES OFFICE

375 Wickham Terrace

Brisbane QLD 4000
TELEPHONE: (61 7) 3886 1543
FACSIMILE: (61 7) 3832 3195
MELBOURNE OFFICE:

2nd Floor, 1 Hobson Street

South Yarra VIC 3141
TELEPHONE: (61 3) 9825 0200
FACSIMILE: (61 3) 9825 0222
EXTRACTIVE INDUSTRIES OFFICE

486 Albert Street

Melbourne VIC 3002
POSTAL ADDRESS:

GPO Box 4352QQ

Melbourne VIC 3001
TELEPHONE: (61 3) 8662 5333
FACSIMILE: (61 3) 8662 5358
PERTH OFFICE:

45 Ventnor Avenue
West Perth WA 6005
TELEPHONE: (61 8) 9389 4452
FACSIMILE: (61 8) 9389 4451
ADELAIDE OFFICE:

Greenhill Executive Suites

213 Greenhill Road
Eastwood SA 5063
POSTAL ADDRESS:

PO Box 229
Fullarton SA 5063
TELEPHONE: (61 8) 8274 3758
FACSIMILE: (61 8) 8373 7210
EXTRACTIVE INDUSTRIES OFFICE

Enterprise House
136 Greenhill Road
Unley SA 5061
TELEPHONE: (61 8) 8300 0180
FACSIMILE: (61 8) 8300 0001
TASMANIAN OFFICE:
EXTRACTIVE INDUSTRIES OFFICE

PO Box 59
Riverside TAS 7250
TELEPHONE: (61 3) 6330 2476
FACSIMILE: (61 3) 6330 2179
WEBSITE: www.concrete.net.au
EMAIL: [email protected]
DESIGN: Helen Rix Design
Disclaimer: Cement Concrete & Aggregates
Australia is a not for profit organisation sponsored
by the cement concrete and aggregate industries
in Australia to provide information on the many
uses of cement and concrete. This publication is
produced by CCAA for that purpose. Since the
information provided is intended for general
guidance only and in no way replaces the services
of professional consultants on particular projects, no
legal liability can be accepted by CCAA for its use.

Page 7 of 7 > HOT-WEATHER Concreting

CCAA respects your privacy. Your details have

been collected to provide you with information on
our activities, publications and services. From time
to time your details may be made available to third
party organisations who comply with the Privacy
Act such as affiliated associations, sponsors of
events and other reputable organisations whose
services we think you may find of interest. If you
do not wish to receive information from CCAA or
wish to be taken off the database please write to
the Privacy Officer, CCAA, Locked Bag 2010,
St Leonards, NSW, 1590