Multilin

DGCM Field RTU

Cost-Effective Monitoring for
Distribution Network Visibility

Versatile Configuration

Most distribution assets are not being monitored, mainly due to space limitations, installation cost and
the cost of the monitoring device itself. The Multilin DGCM is a versatile Field RTU (Remote Terminal Unit)
that can monitor and control a wide range of pole top, pad mount, and underground distribution assets.
This compact solution is designed for easy installation on new equipment and retrofit on installed
assets, making distribution modernization a cost-effective endeavor. The Multilin DGCM supports most
wired and wireless communication architectures along with multiple simultaneous industry standard
communication protocols, resulting in a seamless and straightforward integration into DMS, OMS and
SCADA systems.

Remote downloading of settings and firmware

upgrades reduces trips for field crews

Key Benefits

Reliable Hardware

Improve efficiency and reliability by integrating remote feeders into DMS/OMS/SCADA

Wide operating temperature range

(-40C to +65C ) for harsh environmental
conditions

Track non-technical losses with real-time energy monitoring

Receive early warning signs of asset failure and approaching capacity limits
Eliminate the need for fault passage indicators with built-in per-phase fault detection
Develop customized control schemes with an advanced logic engine and expandable I/O
Enhance fault location and load flow studies using sequence of event records & trending
Reduce setup and commissioning time with easy-to-use software tools
Suitable for use outdoors and in harsh environments (-40C to +65C)

Monitoring and Control Applications

RMU/Pad Mounted
Switchgear
Local Automation,
Switch Management

Pole Top/Pad Mount

Transformer
Transformer Monitoring, Load
Flow Analysis

Cables in Vaults and

Cable Joint Boxes
Fault Monitoring &
Early Overload Warning

Pole Top Applications

Monitoring & Control

Distribution Substation,
LV Systems
Load Monitoring, Theft Detection

End of Line Monitoring

Voltage Optimization Support
Theft Detection

Up to 18 CT and 3 VT inputs for multi-feeder

monitoring and control
Up to 32 digital inputs and 16 digital outputs
for connection adaptability
Support for traditional CTs/VTs and sensor
inputs provides application flexibility

Designed and tested to protection relay

standards
Rugged NEMA 3, IP 44 housing

Cost-Effective
Integration
Unsolicited messaging for immediate issue
notification
Rogowski coil option reduces installation time
Integrated cellular modem delivers accessible
communication

Compact Footprint
Scalable solution supports multiple
application needs
Variable options (stand-alone, with or without
HMI, with or without an enclosure) for
situational requirements

DGCM Field RTU

Application Overview
Distribution systems have grown rapidly in the past few decades, including
the addition of low carbon technologies, causing increased instances of
system losses and poor supply quality. In order to improve operational
planning, grid efficiency, and reliability, utilities need network or topographic
information, real-time load data, as well as the status of distribution assets,
like transformers and feeders.

Overcurrent and under/over voltage conditions detected by the Multilin

DGCM enable early warning signals of system issues. The Multilin DGCM also
monitors for voltage, current, energy, power quality, and breaker/switch
states, which facilitates efficient load planning. Using the Multilin DGCM,
utilities can optimize operational planning, forecast short and long term
loads, perform asset management, and achieve power quality. Additionally,
the Multilin DGCM monitors asset variables, such as oil and winding
temperature, oil pressure, energy release, and number of operations.

RING AND CO
NT
ITO
N
O

L
RO

PO

The Multilin DGCM provides information from various field-based and

substation-based assets, helping utilities achieve voltage optimization, quick
fault detection, fault isolation, and prompt service restoration.

L E -T

O P E Q UIP

ME

N3

TIO
STA

TO

ING & CO
NT
ITOR
R
ON
M

B
SU

NT

ME
UIP

OL

-TO

LE

SU

PO

BS

TAT
IO

Q
PE

N2
NT

MU
NT S

W I TC H G

EA

MO

R/

A
GE

H
ITC

PO

DE

MU

RN

SW

UND

ERG

T
STA

UB

MS

ND

CAB

LES

RMER MONIT
OR
SFO
N
I
A

TR

NG

TR

FRO

1
ION

ROU

IZI

RM

ERG

R
ME

TH

ER

SFO

AN

UND

NG

ROU

ND

CAB

LES

SU

ION

T
IBU
TR
DIS M
LV YSTE
S

ING & CO
NT
ITOR
R
ON
M

L
TIA

LV

GEDigitalEnergy.com

US

IND

EN

SID

RE

N
CO

RID

D IS

T RIB U TI O N S Y

ST

L
RIA

N
CO

ME

SU

OL

ME

OM
/C

L
CIA

EG

EM

OU

ME
UIP

EQ

/R

D
PA

OP
E-T

DGCM Field RTU

Application 1: RMU/Pad Mounted Switchgear

Enhancing RMUs (Ring Main Units) and pad mounted switchgear with
detection functionality has its own challenges regarding the mounting
of conventional MV transformers. The Multilin DGCM enables the utility
to overcome these challenges by offering Rogowski coil and Low Energy
Analog (LEA) compatibility for current and voltage inputs. These features
enable utilities in reducing their overall cost of installation and outage time.

RMU/Pad Mounted Switchgear

Key Benefits
Up to 64 DI
& 32 DO

Real-time load monitoring and profiling of up to 6 feeders (18 individual

phases)

Up to 6
Voltage
Inputs

1 to 6 Feeders

Overcurrent detection per phase (50, 51) for each feeder to identify
faulted circuits and loads approaching overload levels

Up to 6 Current Inputs

DGCM

Expandable digital inputs and outputs enable remote switching of main

incomers or outgoing switches
Support of multiple voltage sensors, such as LEA sensors and PTs, for
cost-effective power quality monitoring
Advanced FlexLogic engine to enable automated switching schemes
Supports traditional CTs and Rogowski coils for quick retrofit solutions

Automation of RMU/pad mounted switchgear with the Multilin DGCM

improves grid reliability by reducing outage time.

Application 2: Cables in Vaults and Cable Joint Boxes

The challenge faced in underground networks is the quick identification of
faults. Deployment of the Multilin DGCM at strategic locations along cable
paths enables faster fault detection as well as early warning signals in case
of overload.

DGCM
1 to 6 Feeders
Up to 18 Current Inputs

Key Benefits
Compact, cost-effective fault detector for underground cable networks
Rogowski coil option to enable retrofit installation in space-limited
locations and to reduce the need for outages

Up to 6 sets of 3-Phase cables

Early warning and fault detection per phase (50, 51) for each feeder to
reduce fault location and feeder downtime
Multiple communication (cellular and radio) and protocol options for easy
integration into DMS and SCADA systems

Using the Multilin DGCM on cables enables faster fault detection and
isolation, reducing outages and crew deployment time.

GEDigitalEnergy.com

DGCM Field RTU

Application 3: Distribution Substation, LV Systems

Most distribution substations and indoor/outdoor LV systems lack asset
monitoring and control. The Multilin DGCM can be used to effectively
monitor power quality, as well as control, when necessary. Rogowski
coil support provides current sensing in hard-to-find spaces and allows
for modifications without an actual outage. The provision of overcurrent
detection provides a vital warning signal well in advance of an actual failure.

DGCM

Up to 6 Voltage Inputs
1 to 6 Feeders
Up to 18 Current Inputs

Key Benefits
Real-time load and energy monitoring and profiling of up to 6 feeders (18
individual phases)
Quick retrofit installation especially in tight spaces through Rogowski coil
current sensors or traditional CTs
Cost-effective energy monitoring through direct voltage measurements
up to 400V or via LEA voltage sensors
LV Substation

Ability to compensate for amplitude and phase shifting associated with

different sensor types
Identification of faulted circuits and loads approaching overload levels
through overcurrent detection per phase (50, 51) for each feeder
Per feeder energy monitoring and logging to help identify locations of
theft detection
Unsolicited messaging to ensure faster response time to SCADA/DMS
systems, making utilities aware of impending abnormalities

Monitoring at key LV consumer substations with the Multilin DGCM can

help in faster fault isolation and energy theft detection.

Application 4: Pole Top/Pad Mounted Transformers

Transformers may be loaded to their maximum capacity without the utility
even realizing it, resulting in reduced transformer life. The Multilin DGCM
enables the monitoring of transformer conditions, identifying transformers
likely to fail. Keeping the utility updated of changing load demands enables
proper planning for current peak loads and future demand.

DGCM
mA Inputs

Key Benefits

Voltage Inputs

Quick retrofit installation especially in tight spaces through Rogowski coil

current sensors or traditional CTs

Current Inputs

Energy monitoring and logging to help theft detection

Remote configuration and firmware updates to simplify fleet
management
Real-time transformer load monitoring to improve load flow studies and
planning
Multiple communication (cellular, radio) and protocol options to ensure
compatibility with existing infrastructure

Transformer monitoring with the Multilin DGCM enables overload

identification, which is key for load planning and asset management.

GEDigitalEnergy.com

DGCM Field RTU

Application 5: Pole Top Applications

The Multilin DGCM can be used for a wide range of pole top applications,
such as remote controls for reclosers, switches, sectionalizers, interchange
tie closures, tap changers and capacitor bank controllers. The Multilin
DGCMs hardware and communication flexibility can be applied to a wide
variety of field applications where monitoring and/or remote control is
required.

SWITCHING DEVICE

LINE

A
B
C

A
B
C

LOAD

Key Benefits
Cost-effective automation of installed field equipment (reclosers,
switches, sectionalizers, interchange tie closures, tap changers and
capacitor bank controllers)

DGCM

Overcurrent detection per phase (50, 51) for each feeder to identify
faulted circuits and loads approaching overload levels
Energy monitoring and logging to help theft detection
Remote configuration and firmware updates to simplify fleet
management
FlexLogic to allow for the creation of customized control schemes that
can be used in many pole top applications
Supports direct voltage measurements up to 400V or LEA voltage sensors
for cost-effective monitoring

Detection functions and FlexLogic enable the Multilin DGCM to be used

for most pole top applications.

Application 6: End of Line Monitoring

Utility and industrial end of line monitoring for Volt/VAr control schemes play
an important role in voltage optimization by ensuring the end customer is
being provided with the proper voltage level. The Multilin DGCM can be used
in applications where only voltage and/or current monitoring is required by
high-end SCADA or DMS systems.

DGCM
mA Inputs
Voltage Inputs

Key Benefits

Current Inputs

End of line voltage and current measurements to help in short term and
long term operational planning
Energy monitoring and logging to help theft detection
Real-time monitoring of voltage for integrating in Volt/VAr control
schemes
Overcurrent detection with alarm/trip to provide early warning signals of
potential failures
Support for multiple communications technologies including cellular and
private radio networks

Volt/VAr control schemes are better optimized using the Multilin DGCM,
as changes in voltage (real-time) are reported almost immediately
(unsolicited messaging) over most utility protocols.

GEDigitalEnergy.com

DGCM Field RTU

Hardware Options

140mm/5.51

The Multilin DGCM is a cost-effective monitoring and control solution for

most pole top, transformer, end of line, RMU and pad mounted switchgear
applications, especially where ease of installation is desired and space
constraints exist . Modular design and expandable I/O support most
customer needs.

Base Unit
(Supports Maximum 2 Modules)
3 Voltage Inputs
Up to 18 Current Inputs (2 Cards)
Up to 32 Digital Inputs and 16 Digital Outputs (2 Cards)
Note : Maximum 2 Cards

150mm/5.91
* Base Unit

Analog Inputs
The Multilin DGCM utilizes many traditional and non-traditional sensors:
Traditional CTs
Traditional PTs
Rogowski Coils
LEA Sensors 0 to 12V Output

Rogowski Coils
Rogowski coils can be used on bare conductors for voltages of up to 600V
and on insulated cables for higher voltages. The use of Rogowski coils
shortens the installation time, reducing outage periods and installation
costs.

Rogowski Coil

GEDigitalEnergy.com

DGCM Field RTU

Advanced Integration
The Multilin DGCM employs industry standard communications
technologies, making it one of the easiest and most flexible controllers to
use and integrate into new and existing SCADA and DMS infrastructures.

Remote Communication

Multiple Protocol Support

The Multilin DGCM can communicate to FDIR/FLISR/SCADA systems via

wireless communications media including:

Multiple communication ports and protocols allow for remote control and
easy access to device and system information.

The Multilin DGCMs integrated cellular modem eliminates the need for
external wireless devices, reducing infrastructure costs.

Wireless radio (MDS or customer specific)

Simultaneous industry standard protocols(slave) supported:

GSM/GPRS

DNP 3.0 Serial and Ethernet

Pre-wired for future radio

Modbus Serial and Ethernet

Options for MDS radios when purchased with enclosure:

IEC 60870-5-104, (IEC 60870-5-101 available Q4 2015)

MDS iNET-II
MDS TransNet

The Multilin DGCM can be used as an I/O extension for relays or for current and voltage measurements into new and existing SCADA and DMS infrastructures.

Indication LED
RJ45 Ethernet Port
Power Supply

USB Serial Port

Low Volt (24 to 60 VDC)

High Volt (85 to 265 VAC/DC)

RS485 Serial Port

Integrated Cellular Card

3-Phase Voltage Input

Traditional: 60 to 440 VAC
LEA: 0 to 12 VAC

Cellular Antenna

Package Solution Option

The Multilin DGCM can be purchased as a stand-alone
unit or installed inside a cabinet. Refer to the order code
section for order options.

GEDigitalEnergy.com

DGCM Field RTU

Automation and Control

Fault/Level Detections

The Multilin DGCM offers powerful I/O and programmable logic (FlexLogic)
options for advanced automation and control, reducing the need for and
costs associated with additional programmable controllers and discrete
control devices.

Effective fault isolation is a key feature for grid reliability. The Multilin DGCM
provides early warning of downstream overcurrent and earth faults. It can
be programmed to isolate a faulted segment, either independently or from
remote SCADA systems. The Multilin DGCM also offers control, monitoring
and diagnostics in one integrated and efficient design.

Remote Control
For both operational efficiency and reliability, the Multilin DGCM provides
remote control for operating overhead switches and pad mount switchgear.
The Multilin DGCM can be locally locked to prevent remote control operations
during field maintenance. Capable of providing both local and manual
control of switchgear, the compact size of the Multilin DGCM enables it to fit
into existing outdoor distribution substations where space constraints exist.

Overcurrent Protection

Set Point Group Control

The Multilin DGCM can be programmed to block instantaneous overcurrent

elements, and raise the pick-up time of overcurrent elements, when a cold
load condition is detected. Cold load conditions are sensed during the
closing of the breaker on a feeder that has been de-energized for a long
time. The feeder in-rush and motor accelerating currents during breaker
closing may be above some overcurrent protection settings.

The Multilin DGCM has three set point groups. The activation of the groups
can be done either from SCADA, HMI or via a digital input.

Virtual Inputs and Outputs

The Multilin DGCM provides 32 virtual inputs and 32 virtual outputs that
provide users with the ability to send commands to the device. The Multilin
DGCM can accept commands from SCADA, through the front HMI, or front
USB port, and issue commands, such as close or open.

FlexLogic

Instantaneous and time overcurrent functions are available for phase, and
neutral currents. A variety of time curves are provided, including IEEE/
ANSI, IEC A/B/C long time inverse and short time inverse definite time and
user-programmable curves.

Cold Load Pick-Up

Over Voltage (OV) Detection

The phase OV detection alerts utilities of sustained OV conditions. The OV
detector generates an alarm when the voltage exceeds the selected voltage
level after a specified time delay.

FlexLogic in the Multilin DGCM helps reduce costs by providing the ability
to create customized control schemes, minimizing the need for auxiliary
components and wiring. Schemes can be configured with FlexLogic,
specifying what actions need be taken, based on the status of fault
detections or control elements, and inputs driven by connected sensors and
equipment .

1
Save

Restore

Default

VIRTUAL IP 1 ON (SCADA CLOSE)

AND (2)
AND (3)

AND (2)
BNK1 PH HI IOC OP
CONT IP 1 ON (SWITCH 1 OPEN)
AND (2)

= CLOSE INCOMER A (VO1)

AND (2)

TIME

PHASE OVERVOLTAGE BNK1 OP

PHASE UNDEROVERVOLTAGE BNK2 OP

OR (2)

BNK1 PH HI IOC DPO

OR (2)

2
4

AND (3)
= VIRTUAL OP 1 (VO1)

Using FlexLogic, customers can develop customized control schemes for

multiple applications.

3
CURRENT

Custom FlexCurves can be constructed to coordinate with other

upstream and downstream protection devices.

GEDigitalEnergy.com

DGCM Field RTU

Under Voltage (UV) Detection

Trending and Data Logging

The phase UV detection alerts utilities against sustained UV conditions. The

UV detector generates an alarm when the voltage drops below the selected
voltage level after a specified time delay.

The Multilin DGCM provides a 200 channel RMS recorder for advanced
disturbance diagnostic features. Data recording can be set to record from 1
minute to 60 minute intervals. This significantly reduces the time and cost
associated with troubleshooting power system events and reconstructions.
The data can be immediately analyzed for trends, or stored for archival
purposes.

Power Loss
The Multilin DGCM can detect a power loss condition in each phase of the
power distribution line. Open/close commands are blocked, unless currents
and voltages of each phase fall below minimum set values. When the switch
is closed, the power loss detection of the source side is used to control the
open command execution.

Measurements
The Multilin DGCM provides high accuracy metering and recording of AC
signals, measuring the following key parameters:

Basic Measurements

EVENT

DATE

TIME

53

02/03/2012

16:22:44:103

TOC pickup

52

02/03/2012

16:22:44:220

Loss 01 Power

51

02/03/2012

16:22:45:115

TOC drop off

50

02/03/2012

16:22:45:175

AS first shot

49

02/03/2012

16:22:47:680

TOC pickup

48

02/03/2012

16:22:47:710

Loss of Power

47

02/03/2012

16:22:48:132

TOC drop off

46

02/03/2012

16:22:48:192

A5 second shot

45

02/03/2012

16:22:48:412

Switch Open

Current: Ia, Ib, Ic, In

Phase-to-phase and phase-to-ground voltages for bus and line: Van, Vbn,
Vcn, Vbb, Vab, Vbc, Vca
Active power (per-phase and total): Wa, Wb, Wc, W

CAUSE OF EVENT

The Multilin DGCM event recorder enables users to analyze the

sequence of events after each triggered event. Each event is stored
with the event number, date, time and analog data of interest.

Reactive power (per-phase and total): VARa, VARb, VARc, VAR

Total active, reactive and apparent energy: MWh, MVARh, MVAh

02/25/2013
13:05:21.626000

5hr 0 m

15 hr 0 m

02/25/201313:05:21.626000

02/25/201313:05:21.626000

10 hr 0 s

Power factor (per-phase and total)

Phase A Current Bank1

280.000 (Amps)
160.000 (Amps)
-120.000 (Amps)

Frequency

Phase B Current Bank1

270.000 (Amps)
190.000 (Amps)
-80.000 (Amps)

Power Quality Measurements

Phase C Current Bank1

230.000 (Amps)
130.000 (Amps)
-100.000 (Amps)

Voltage sag/swell

Phase A RMS Current Bank1

Current unbalance

198.02.000 (Amps)
113.154.000 (Amps)
-84.866.000 (Amps)
Phase B RMS Current Bank1

Demand: voltage, current, active power, apparent power, energy,

temperature

190.948.000 (Amps)
134.371.000 (Amps)
-56.577.000 (Amps)
Phase C RMS Current Bank1

162.659.000 (Amps)
91.938.000 (Amps)
-70.721.000 (Amps)

2nd to 15th harmonic for current

2nd to 15th harmonic for voltage

THD in 20% for current

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

The Multilin DGCM data logger helps in better understanding the analog
channel behavior, by sampling at a selectable time interval rate of 1 to 60
minutes.

THD in 20% for voltage

These data points can be easily integrated into a customers database for
seamless viewing through SCADA or a DMS system, such as GEs PowerOnTM
Control or GENe.

Data Management and Diagnostics

Event Recorder
To enable more effective post event analysis and troubleshooting, the
Multilin DGCM provides an integrated event recorder and detailed diagnostic
features. The event recorder offers:
Storage for up to 1024 time stamped events
Pick-up & drop-off of detection elements
Instantaneous values of voltage/current at the time each event occurred

GEDigitalEnergy.com

DGCM Field RTU

Software and Configuration

The EnerVista suite is an industry leading set of software programs that
simplifies every aspect of using the Multilin DGCM.
EnerVista provides all the tools to monitor the status of the protected asset,
maintain the controller, and integrate information, measured by the Multilin
DGCM, into SCADA or DMS monitoring systems.

Included in Launchpad is a document archiving and management system

that ensures critical documentation is up-to-date and available when
needed.
Documents available include:
Manuals

The ability to easily view sequence of events is an integral part of the

setup software, as postmortem event analysis is critical to proper system
operation.

Application Notes

EnerVista Launchpad

Wiring Diagrams

EnerVista Launchpad is a powerful software program that provides

users with all of the setup and support tools needed for configuring and
maintaining GEs Multilin products. The setup tools within Launchpad allow
for the configuration of devices in real-time, by communicating via serial,
Ethernet or modem connections, or offline, by creating device setting files to
be sent to devices at a later time.

FAQs

Guide Form Specifications

Brochures

Service Bulletins

Setup with EnerVista Software

EnerVista setup software can reduce device setup and configuration time.

Single Click Device

Communications
Quick Link Diagnostic
Information

Online Device Configuration

and Monitoring

Menu Driven Device

Configuration

Offline Device Setting File

Configuration

10

GEDigitalEnergy.com

DGCM Field RTU

Technical Specifications
POWER SUPPLY

PHASE VOLTAGE INPUTS

COMMUNICATIONS

HIGH RANGE POWER SUPPLY

PHASE VOLTAGE INPUTS (Direct Connection)

SERIAL

Nominal: 110 to 240 VAC

125 to 250 VDC
Range: 85 to 265 VAC
(50 and 60 Hz)
85 to 265 VDC

Range:
60 to 440 VAC
Nominal Frequency:
50/60 Hz
Burden:
<0.25 VA at 120 V
Accuracy: 0.5% Throughout Range
Voltage Withstand: 2xVn Continuously, 3xVn 10s

RS485 Port:
Baud Rates:
Protocol:

LOW RANGE POWER SUPPLY

Nominal:
Range:

24 to 48 VDC
20 to 60 VDC

PHASE CURRENT INPUTS

PHASE CURRENT INPUTS (CTS)
Range:
0.05 to 2.50 CT
Input Type: 1 A or 5 A
(SW Selectable)
Nominal Frequency:
50/60 Hz
Burden:
<0.1 VA at Rated Load
Accuracy: 1% of Reading 0.2% Full
Scale
CT Withstand: 1 Second at 20 Rated
Current, Continuous at 4x
Rated Current

PHASE CURRENT INPUTS

(Rogowski Coils)

ETHERNET (COPPER)

PHASE VOLTAGE INPUTS (LEA)

Modes: 10/100 MB (Auto-Detect)

Connector: RJ45
Protocol:
IEC 60870-5-104

Range:
0 to 10 VAC
Nominal Frequency:
50/60 Hz
Input Impedance:
> 10 M
Accuracy: 0.5% Throughout Range
Voltage Withstand: 2xVn Continuously,
3xVn 10s

USB
Standard Specification:
Data Transfer Rate:

Quad-Band EGSM 850/900/1800/1900 MHz

GSM/GPRS Protocol Stack 3GPP Release 4 Compliant
Sensitivity: -107 dBm (typ.)
@ 850 / 900 MHz
-107 dBm (typ.)
@ 1800 /1900 MHz
Extended temperature range: -40C to +85C

DIGITAL INPUTS
Thresholds:
20 to 64 VDC for Low Range
100 to 240 VAC for High Range
Recognition Time:
1/2 Cycle
Debounce Time: 10 to 100 ms, Selectable,
in Steps of 5 ms
Contact Material:
Operate Time:
Continuous Current:
Make and Carry for 4s:

Compliant with USB 2.0

115 kbps

GPRS

DIGITAL I/O

DIMENSIONS

DIGITAL OUTPUTS
IP67

Opto-Coupled
Up to 115 kbps
Modbus RTU, DNP 3.0,
(IEC 60870-5-101 available
Q4 2015)

Base Size: 150 mm (W) x 140 mm (H) x

110 mm (D);
5.91 (W) x 5.51 (H) x 4.33 (D)
Weight (Base):
2 kg; 4.41 lbs

Silver-Alloy
10 ms
6A
15 A per ANSI C37.90

Type Tests
TEST DESCRIPTION

LEVELS

STANDARD

TEST DESCRIPTION

IMMUNITY
ESD

LEVELS

STANDARD

ELECTRICAL (Category IV, 300V)

8 kV contact/
15 kV air discharge

IEC 61000-4-2, EN60255-22-2

Dielectric Strength

EN60255-5

Radiated RF Immunity

10 V/m (80 MHz to 1 GHz)

3 V/m (1.4 GHz to 2.0 GHz)
1 V/m (2.0 GHz to 2.7 GHz)

IEC 61000-4-3:2002, EN6025522-3

Basic & Supplementary

Insulation: 3.3 kV at least
1 min

Impulse

Reinforced Insulation: 5.4 kV

at least 1 min

IEC 61010-1:2010

Radiated RF Immunity

80 MHz-1 GHz 20 V/m included

Frequency Sweep, Keying Test
and Spot Frequencies (except
GSM)

IEEE C37.90.2:2004

Clearance & Creepage

Category IV, 300 V, Table K 4

IEC 61010-1:2010/

Fast Transient

4 kV at 5 kHz

IEC 61000-4-4:2012/
IEC60255-22-4

Surge

2 kV

IEC 60255-22-5

Conducted RF Immunity

10 Vrms (150 kHz to 80 MHz)

IEC 61000-4-6, IEC 60255-22-6

Power Frequency Magnetic

Field Immunity

Level 5: 100 A/m continuous

1000 A/m 1 to 3 s

IEC 61000-4-8:2001

Voltage Dip

0% during 1 cycle
40% during 10/12 cycles
70% during 25/30 cycles
80% during 250/300 cycles

IEC 61000-4-11:2004

Voltage Interruption

0% during 250/300 cycles

IEC 61000-4-11:2004

Radiated RF Emission

Group 1 & Class B

CISPR 11, IEC 60255-25

Conducted RF Emission

Group 1 & Class B

CISPR 11, IEC 60255-25

ENVIRONMENTAL
Operating temperature: 40C to + 65C as per IEC 60068
Relative humidity cyclic: IEC 60068-2-30; 55C 95% humidity

MECHANICAL
Sinusoidal vibration: IEC 60068-2-6:2007 Class 1
Shock and bump: IEC 60068-2-27:2008 Class 1
Seismic: IEC 60068-3-3:1991 Class 2

MISCELLANEOUS

EMISSIONEN

Ingress of solid objects and water: IEC 60529:2007 IP44 (with external enclosure) NEMA 3/4
for cabinet
Resistance to mechanical stresses: IEC 61010-1:2010 (Paragraph 8)
Protection against the spread of fire: IEC 61010-1:2010 (Paragraph 9)
IEC 61000-3-2 (2008): Limits for harmonic current emmissions
IEC 61000-3-3 (2008): Limitation of voltage changes, voltage fluctuations and flicker in public
low-voltage supply systems

GEDigitalEnergy.com

11

Ordering Codes
DGCM FIELD RTU
DGCM
Base type

DGCM

Description
Field RTU

Base Unit Includes : 3 x Voltage Inputs (60 to 440 VAC)

Base Unit Includes : 3 x Voltage Inputs (0 to 12 VAC, LEA)

Power Supply

High Volt AC Power Supply (85 V to 265 VAC/DC)

Low Volt DC Power Supply (24 to 60 VDC)

Modules

Controller

9 x CT Inputs 5 Amp/1 Amp Secondary

9 x Rogowski Coil Inputs

16 x Digital Inputs, 8 x Digital Outputs (64 DI & 32 DO Maximum,

100 to 240 VAC/DC)

16 x Digital Inputs, 8 x Digital Outputs (64 DI & 32 DO Maximum,

24 to 60 VDC)

None
1

Controller Only (No Display)

2
Wireless Radios

Controller in Enclosure (No Display)

X

No External Communications

Long Range High-Speed Serial Communication

MDS TransNet (EL805-MD9X1AFCD1WN)
- Available with controller in enclosure

Long Range Ethernet & Serial Communication

MDS iNET-II (iNETII-MD9A1AVFCD1NN0)
- Available with controller in enclosure

Rogowski Coil
ROGS
Rogowski Coil
Sensors

ROGS

Rogowski Coil Sensor, 3 m termination length required to be

ordered when F option for current input is chosen

Digital Energy
650 Markland St.
Markham, ON
Canada L6C 0M1
Toll Free (NA Only): 1-800-547-8629
Tel: 905-927-7070
Fax: 905-927-5098
[email protected]

GEDigitalEnergy.com
IEC is a registered trademark of Commission Electrotechnique Internationale.
IEEE is a registered trademark of the Institute of Electrical Electronics Engineers, Inc.
ANSI is a registered trademark of American National Standards Institute, Incorporated.
Microsoft is a registered trademark of Microsoft Corporation.
Modbus is a registered trademark of Schneider Automation.
GE, the GE monogram, Multilin, FlexLogic, EnerVista, MDS and PowerOn are trademarks of the
General Electric Company.
GE reserves the right to make changes to specifications of products described at any time
without notice and without obligation to notify any person of such changes.
Copyright 2015, General Electric Company. All Rights Reserved.

GEA-12715C(E)
English
150209