1052 Size 70 PDF

Product Bulletin
1052 Actuator
61.1:1052
February 2015
D104082X012
Fisherr 1052 Size 70 Diaphragm Rotary

Actuator
Fisher 1052 size 70 springreturn diaphragm rotary
actuators operate splined shaft rotary valves, such as
8580, 8532, 8590, CV500, V500, and VeeBallt
(V150, V200 and V300) valves. 1052 actuators are
suitable for onoff service or for throttling service.
This actuator is designed for easy installation of a
broad range of options: limit switches, position
indicating switches, positioners, and manual
overrides. Option applicability varies with actuator
size. Refer to the specifications table and table 4 for
information concerning option applicability and
specifications.
Features
nApplication Flexibility-- 1052 rotary actuators are
available with failopen or failclose construction

and can be mounted in any of four actuatorvalve
mounting positions. See figure 5 for mounting
positions. These actuators can be mounted on a
broad range of Fisher valves or used with other
equipment.
W8508-3
Typical Fisher 1052 Actuator with VeeBall Valve and

FIELDVUE DVC6200 Digital Valve Controller
nMinimal Dead Band-- Single joint linkage with
splined and clamped lever minimizes lost motion

and improves control accuracy.
nLong Service Life-- Rugged construction provides
stability, corrosion resistance, and protection from

deformation should overpressurization occur.
www.Fisher.com
nSafety-- The 1052 actuator has an externally
accessible spring adjuster to relieve spring

compression (see figure 1). Actuatorvalve linkage
is completely enclosed, yet the valve packing
adjustment remains accessible without removing
any parts (see figure 2).
Product Bulletin
1052 Actuator
61.1:1052
February 2015
D104082X012
Specifications
Available Configurations
For onoff service without a positioner or for
throttling services with or without a positioner
Direct Acting: Increasing loading pressure extends
the diaphragm rod out of the spring barrel
piping. If stroking time is critical, consult your

Emerson Process Management sales office
Diaphragm Casing Displacement
See table 1
Actuator Sizes
70
Construction Materials
Standard Diaphragm Pressure Ranges

J 0 to 2.3 bar (0 to 33 psig), J 0 to 2.8 bar (0 to 40
psig), and J 0 to 3.8 bar (0 to 55 psig)
Material Temperature Capabilities(1)
Maximum Diaphragm Sizing Pressure(1)

3.8 bar (55 psig)
Maximum Diaphragm Casing Pressure(5)
4.5 bar (65 psig)
Nominal Valve Shaft Rotation
J 90 degrees (standard), J 60 degrees (optional), or
J 75 degrees (optional)
Valve Shaft Diameters, mm (Inches)
J 31.8 (11/4), J 38.1 (11/2),
J 44.5 (13/4), or J 50.8 (2)
See table 3
Nitrile Diaphragm or ORings(3): -40 to 82_C (-40 to

180_F)
Silicone Diaphragm: -40 to 149_C (-40 to 300_F)
Travel Indication
Graduated scale and pointer combination located on
actuator end of valve drive shaft
Pipe or Tubing Connection Sizes
Standard: 1/4 NPT internal
Optional: J 1/2 or J 3/4 NPT internal,
and J 3/4 NPT PipeAway vent opening
Mounting Positions
See figure 5
Maximum Breakout Torque(2)

Up to 1370 NSm (12,100 lbfSin)
Approximate Weights
Stroking Time
Dependent on rotation, spring rate, initial spring
compression, supply pressure, and size of supply
Options
See table 2
Option applicability varies with actuator size. Refer to

table 4 and the Options section.
1. Use this value to determine the maximum torque output. The pressure/temperature limits in this bulletin and any applicable standard or code limitation for the actuator should not be
exceeded.
2. Actual actuator torque available depends on specific construction and casing pressure. For information on torque requirements of the valve being considered, contact your Emerson Process
Management sales office.
3. Nitrile Orings are used in the optional topmounted handwheel and in the optional up and down travel stop assemblies.
4. For higher temperature ratings, contact your Emerson Process Management sales office.
5. This maximum casing pressure is not to be used for normal operating pressure. Its purpose is to allow for typical regulator supply settings and/or relief valve tolerances.
Options
61.8:1078 (D101339X012) for handwheel actuator

specifications.
TopMounted Handwheel: For infrequent use as a

manual actuator or for use as an adjustable up travel
stop (see figure 4). For repeated or daily manual
operation, the unit should be equipped with a
declutchable handwheel actuator.
Limit Switches: MicroSwitch or NAMCO switches for

one or two singlepole, doublethrow contacts. See
separate bulletins for limit switch information.
Declutchable Handwheel Actuator: A sidemounted

manual actuator can be used to provide onsite control
and to provide override capabilities. See bulletin
Position Indicating Switch: TopWorx DXP M21GNEB

switch for one through six single pole, double throw
switch contacts are available. See separate bulletin for
position indicating switch information.
Product Bulletin
1052 Actuator
61.1:1052
February 2015
D104082X012
Positioner: For precise positioning of the valve disk or
ball, the actuator should be equipped with a
positioner. Under some service conditions, the 1052
actuator may be used successfully in these
applications without a positioner. For additional
information, contact your Emerson Process
Management sales office with complete service
conditions.
Figure 1. Sectional Views of Spring Seat Construction

Details
W4742-2crop
Adjustable DownTravel Stop: Used to limit the

actuator stroke in the downward direction
(see figure 3).
TYPICAL OF THE 1052

ACTUATOR WITH
ADJUSTABLE SPRING SEAT
Adjustable UpTravel Stop: Used to limit the actuator

stroke in the upward direction (see figure 3).
Actuator Locking Mechanism: An actuator locking
mechanism is available. It can be used to keep the
actuator in a locked position (the same as the
springfail position) during maintenance. The padlock
is customer supplied, and the mechanism requires a
modified actuator housing.
Pipe Away Vent: Some applications use natural gas or
other hazardous gases as a supply pressure to the
actuator. These applications sometimes require the
actuator housing to be vented, reducing the
accumulation of gases. For new constructions and
retrofit kit information, contact your Emerson Process
Management sales office with complete service
conditions.
Table 1. Diaphragm Casing Displacement
CASING
SIZE
70
CLEARANCE
VOLUME(1)
cm3
Inches3
3490
213
CASING VOLUME(2)
60 Degree
Rotation
cm3
Inches3
13,929
850
90 Degree
Rotation
cm3
Inches3
19,025
1161
1. Volume when the diaphragm is in the up position.

2. Includes clearance volume.
70
1052 ACTUATOR
Kg
Pounds
123
272
TOPMOUNTED
HANDWHEEL
Kg
Pounds
21.3
PART
MATERIAL
Actuator
Actuator Housing and Spring

Barrel
Cast iron
Diaphragm
Nitrile on nylon or silicone on

polyester
Diaphragm Head
Cast Iron
Diaphragm Casing(1)
Pressed steel
Diaphragm Rod
Steel
Housing Cover
Cast iron or aluminum
Lever
Ductile iron
Optional TopMounted Handwheel Assembly

Handwheel and Handwheel Body
Cast iron
Handwheel Stem
Bronze
ORings
Nitrile
Pusher Plate
Cast iron or steel
Optional Down Travel Stop Assembly

Closing Cap
Brass
Oring
Nitrile
Stem
Stainless steel
Travel Stop Body
Cast iron
Optional Up Travel Stop Assembly
Table 2. Approximate Actuator Weights

SIZE
Table 3. Construction Materials
47
Closing Cap
Brass
ORing
Nitrile
Stem
Bronze
Travel Stop Body
Cast iron
Product Bulletin
1052 Actuator
61.1:1052
February 2015
D104082X012
Figure 2. Sectional Views Typical of 1052 Actuator
W22913
W38131
Figure 3. Optional Adjustable Travel Stops
36A6250B
28A1761B
TYPICAL ADJUSTABLE UP TRAVEL STOP
TYPICAL ADJUSTABLE DOWN TRAVEL STOP
Product Bulletin
1052 Actuator
61.1:1052
February 2015
D104082X012
Table 4. Construction Features and Option Applicability

STANDARD TRAVEL
STOP
ACTUATOR SIZE
ACTUATOR TYPE
Style
70
OPTIONAL TRAVEL STOP
1052
Fixed
Style
Topmounted
uptravel stop or
downtravel stop
Range of
Adjustability
90 degrees
OPTIONAL
MANUAL
OVERRIDE
ACCESSORY
SWITCH
MOUNTING
Mechanically
Operated
Switches
Topmounted
handwheel for
infrequent
operation or
sidemounted
manual actuator
for routine
operation
Externally
mounted, lever
operated
Figure 4. TopMounted Handwheel
W3145
Product Bulletin
1052 Actuator
61.1:1052
February 2015
D104082X012
Table 5. Mounting Styles and Positions

VALVE SERIES OR DESIGN
MOUNTING
ACTION(1)
RightHand
PDTC
PDTO
BALL/PLUG
ROTATION
TO CLOSE
CCW(3)
CCW
LeftHand
PDTC
PDTO
LeftHand
(Optional)(2)
PDTC
PDTO
VALVE SERIES OR DESIGN
V250
V150, V200 and

V300
CV500 and
V500
A
B
A
B
A
B
DISK/BALL
ROTATION
TO CLOSE
CW
CW
NA
NA
8532, 8560,
8580, and
8590
B
A
CCW
CCW
NA
NA
D
C
D
C
CW
CW
C
D
C
D
CW(4)
CW
NA
NA
C
D
NA
NA
NA
NA
NA
NA
NA
NA
V250
1. PDTCPushdowntoclose, and PDTOPushdowntoopen.

2. A left hand ball will be required for NPS 3 through 12 V150, V200 and V300, Series B and NPS 14 through 20, with or without an attenuator.
3. CCW = counterclockwise
4. CW = clockwise
Figure 5. Mounting Styles and Positions (also see table 5)

STYLE A
STYLE B
POSITION 1
POSITION 1
STYLE D
FLOW
STYLE C
LEFTHAND
MOUNTING
2
4
2
3
RIGHTHAND MOUNTING
STYLE C
STYLE D
STYLE B
STYLE A
POSITION 1
POSITION 1 1
FLOW
2
2
3
RIGHTHAND
MOUNTING
43A6505A
A15843
Notes:
1
Position
1 is standard; Positions 2 through 4 (shown in dotted lines) are alternatives.
LEFTHAND MOUNTING
Product Bulletin
1052 Actuator
61.1:1052
February 2015
D104082X012
Figure 6. Dimensions (also see tables 6, 7 and 8)
JC DIA
1/418
NPT
HC
14A7221D
A3023
TOPMOUNTED
HANDWHEEL
W DIA
14A7222F
A22064
ACTUATOR/VALVE BODY
MOUNTING DIMENSIONS
1/214 NPT
SIZE 70
C DIA
H
F
Y
V
P
14A7222F
16A0600B
B14124
1052 SIZE 70 ACTUATOR
Installation
The actuator is normally positioned vertically in a
horizontal pipeline. Four mounting styles and four
positions for each style are possible (see figure 5). Due
to its weight, the 1052 size 70 actuator must be
externally supported if mounted in the horizontal
position.
When looking in the direction of flow in the pipeline,
an actuator is righthand mounted when it is on the
right side of the pipeline, and an actuator is lefthand
mounted when it is mounted on the left side of the

pipeline.
By Emerson Process Management definition, forward
flow is into the face side of the disk or ball, and reverse
flow is into the hub side of the disk or ball.
Dimensions for both actuator types are shown in figure
6. These dimensions should be used in conjunction
with the mounting positions shown in figure 5. Make
clearance considerations before mounting the
actuator to determine the most suitable mounting
position.
Product Bulletin
1052 Actuator
61.1:1052
February 2015
D104082X012
Adjustable Travel Stops
Figure 7. Actuator Locking Mechanism
Adjustable travel stops (in addition to those shown in

figure 3) are available as discussed below.
ACTUATOR
LEVER
As used here, down or downward means in a direction

toward the valve shaft and away from the piston and
diaphragm.
MODIFIED
ACTUATOR
HOUSING
An adjustable down travel stop is installed in a special

actuator housing. The assembly consists of a special
housing, cap screw, locknut, lever, and rod end
bearing. The cap screw can be positioned to limit
downward travel of the actuator lever to any rotation
between 0 and 90 degrees.
PADLOCK
(CUSTOMER
SUPPLIED)
LOCKING
MECHANISM
The locking mechanism shown in figure 7 is not to be

used as a travel stop. Please specify an adjustable
travel stop assembly instead.
A60192
Table 6. Dimensions
C
ACTUATOR SIZE
70
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
536
21.12
849
33.44
64
2.50
121
4.75
186
7.31
76
3.00
Table 7. Actuator / Valve Body Mounting Dimensions

VALVE SHAFT DIAMETER
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
31.8 38.1
11/4 11/2
235
9.25
46
1.81
148
5.81
17.5
0.69
44.5 50.8
13/4 2
273
10.75
51
2.00
286
11.25
20.6
0.81
Table 8. Dimensions for TopMounted Handwheel

HC
JC
ACTUATOR
SIZE
mm
Inches
mm
Inches
70
378
14.88
356
14.00
Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance
of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Fisher, FIELDVUE, Vee-Ball, and TopWorx are marks owned by one of the companies in the Emerson Process Management business unit of Emerson Electric
Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the
property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are
governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Process Management
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
E
8 2015 Fisher Controls International LLC. All rights reserved.

1052 Size 70 PDF

Uploaded by

Copyright:

Available Formats

1052 Size 70 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1052 Size 70 PDF

Uploaded by

Copyright:

Available Formats

What are the main components of the 1052 actuator?

What are the main components of the 1052 actuator?

What are some of the features and benefits of the 1052 actuator?

What are some of the features and benefits of the 1052 actuator?

Product Bulletin

Fisherr 1052 Size 70 Diaphragm Rotary

available with failopen or failclose construction

Typical Fisher 1052 Actuator with VeeBall Valve and

nMinimal Dead Band-- Single joint linkage with

splined and clamped lever minimizes lost motion

stability, corrosion resistance, and protection from

nSafety-- The 1052 actuator has an externally

accessible spring adjuster to relieve spring

piping. If stroking time is critical, consult your

Standard Diaphragm Pressure Ranges

Material Temperature Capabilities(1)

Maximum Diaphragm Sizing Pressure(1)

Nitrile Diaphragm or ORings(3): -40 to 82_C (-40 to

Maximum Breakout Torque(2)

Option applicability varies with actuator size. Refer to

61.8:1078 (D101339X012) for handwheel actuator

TopMounted Handwheel: For infrequent use as a

Limit Switches: MicroSwitch or NAMCO switches for

Declutchable Handwheel Actuator: A sidemounted

Position Indicating Switch: TopWorx DXP M21GNEB

Figure 1. Sectional Views of Spring Seat Construction

Adjustable DownTravel Stop: Used to limit the

TYPICAL OF THE 1052

Adjustable UpTravel Stop: Used to limit the actuator

1. Volume when the diaphragm is in the up position.

Actuator Housing and Spring

Nitrile on nylon or silicone on

Cast iron or aluminum

Optional TopMounted Handwheel Assembly

Cast iron or steel

Optional Down Travel Stop Assembly

Travel Stop Body

Optional Up Travel Stop Assembly

Table 2. Approximate Actuator Weights

Table 3. Construction Materials

Travel Stop Body

Figure 2. Sectional Views Typical of 1052 Actuator

Figure 3. Optional Adjustable Travel Stops

TYPICAL ADJUSTABLE UP TRAVEL STOP

TYPICAL ADJUSTABLE DOWN TRAVEL STOP

Table 4. Construction Features and Option Applicability

OPTIONAL TRAVEL STOP

Figure 4. TopMounted Handwheel

Table 5. Mounting Styles and Positions

VALVE SERIES OR DESIGN

V150, V200 and

1. PDTCPushdowntoclose, and PDTOPushdowntoopen.

Figure 5. Mounting Styles and Positions (also see table 5)

Figure 6. Dimensions (also see tables 6, 7 and 8)

1052 SIZE 70 ACTUATOR

mounted when it is mounted on the left side of the

Adjustable Travel Stops

Figure 7. Actuator Locking Mechanism

Adjustable travel stops (in addition to those shown in