CSTR For Fisher Tropsch

BENCH SCALE UNITS
AND PILOT PLANTS FOR

POLYOLEFINS
RESEARCH
POLYMERZATION
CHAIN GROWTH
STEP GROWTH
Unsaturated molecules
Chemical reaction between multifunctional

monomers molecules.
ADDITION
CONDENSATION
Reaction does not involve low

molecular byproduct formation.
FREE RADICAL
T, P activation
By-product formation. Polyurethanes

Polyamide (nylon); PET
COORDINATION
Coordination catalyst.
Polyethylene (PE); Polypropilene (PP);

Polyvinyl chloride (PVC); Polystyrene (PS)
ADDITION
IONIC
WIDE RANGE OF PROCESS AND PRODUCTS

PID Eng&Tech experience is focused on POLYOLEFINS
PRODUCTION: POLYETHYLENE AND POLYPROPYLENE
Other processes can be studied.
POLYOLEFINS PRODUCTION PROCESSES

HIGH PRESSURE
PROCESSES
LOW PRESSURE
PROCESSES
High temperature and pressure

600-3000 barg; 200-300C
LDPE
SLURRY
Gas monomer
Liquid solvent
Solid polymer
Reactors: CSTR, LOOP
70-110C
8-40 bar
Catalytic processes
(Coordination catalysts)
GAS
Gas monomer
Solid polymer
Reactors: CSTR, Fluidized bed
70-110C
20-25 bar
SOLUTION
Gas monomer
Liquid solvent
Diluted polymer
Reactors: CSTR
170-200C
90-100 bar
LABORATORY EQUIPMENT FOR POLYOLEFINS

RESEARCH
SLURRY PHASE
SEMI-BATCH
STIRRER TANK
REACTORS
CONTINUOUS
STIRRED TANK
REACTORS
Most common laboratory

scale installations.
Installations easy to operate.
Catalyst testing
One reactor o several reactors

in series.
No commercial installations.
Product development
PRODUCTS FABRICATED BY PID Eng&Tech
GAS PHASE
SEMI-BATCH
STIRRER TANK
REACTORS
Complex installations
because of stirring and heat
removal.
No commercial installations.
No PID Eng&Tech experience.
Elements in Slurry Phase Polyolefins Production

Main streams:
MONOMER: Ethylene; Propylene
HYDROGEN (control agent of the molecular

weigh of the polymer)
COMONOMERS: low molecular weight

olefins (ethylene, propylene, 1-butene; 1hexene)
SOLVENT: heptane; hexane; isobutane
CATALYST: supported coordination catalyst

(Ziegler-Natta; chromium oxide;
metallocene)
COCATALYST: catalyst activation and

scavenger (TEA, TIBA )
Raw Material Purification
Removing potential traces of water and oxygen

from fluid stream.
Pre-purified area comprises adsorption beds in

series for each feed line.
Typical adsorbents: activated alumina; molecular

sieve, etc.
Regeneration process: high temperature and

sweeping with an inert gas.
In situ regeneration system can be included.
Laboratory Scale Batch Units
SS316 stirred autoclave reactor 500 ml to 4 l

Heating jacked; cooling coil.
Maximum pressure: 50 bar
Maximum temperature: 100C
Continuous gas monomer, hydrogen and
comonomer feed lines.
Continuous liquid comonomer lines.
Solvent addition system.
Gas composition analysis system: MicroGC
Reactor Control Pressure.

Monomer feed line.
Monomer is added continuously during the reaction

to replenish the consumption for the polymer
formation.
Reactor pressure is controlled adjusting the gas
monomer addition.
Pressure regulation can be carried out by a manual
pressure regulator or through the mass flow controller
control valve.
Mass
flow
controller
measures
monomer
consumption.
In the case of polypropylene, polymerization can be
carried out in liquid monomer (Bulk Polymerization).
Pressure is established by the liquid-vapor equilibrium
of the propylene.
Comonomer feed lines.
Comonomers can be added like gases or liquids

according to the operation pressure and the
liquid-vapor equilibrium of the compound.
Hydrogen and gas comonomers flow are

measured and controlled by Mass Flow
Controllers. Heating tracing of the line is often
necessary to maintain the vapor phase.
Liquid comonomers can be added by a high

performance pump or by nitrogen pushing and
a liquid mass flow controller.
Vapor-Pressure Line for Propylene

T (F)
T (C)
P (barg)
35.6
59.0
15
140
60
26
Gas Phase Composition Control
Final product properties depend of the monomer,

hydrogen and comonomer concentration.
Hydrogen/monomer and comonomer/monomer

composition ratios in gas phase during the reaction can
be controlled.
Gas composition can be measured at nearly real time

(2-4 min of delay) by a MicroCG.
Result of this analysis can be integrated in the control

system. Hydrogen and commoner flows are modified
for keeping a constant composition in the reactor.
Batch Operations
Nitrogen and vacuum lines are used for system

inertization, pressure test and cleaning.
Solvent is loaded in batch mode before the

reaction. Addition can be carried out through a
pump or by nitrogen pushing from a graduated
burette.
Catalyst (solid) is loaded in the beginning of

the reaction sweeping it with the monomer.
Cocatalyst (solution) is injected to solvent

before reactor pressurization.
Laboratory Batch Units

Advantages and Requeriments
Polymerization reactions are complex processes.

Equipments easy to operate.
Procedures easy to standardize and validate.
Low investment, low waste of raw materials and
catalyst.
Catalyst productivity test.
Product properties screening: melting index; density;
comonomer incorporation.
Small quantities of polymer (< 250g). Limitations in
product analysis.
PID Eng&Tech has a widely experience in these
installations.
Pilot plant for continuous polyethylene production

at micro-scale
OBJECTIVES
MAIN CHALLENGES
Micro-scale industrial process

simulation.
Solid suspension transfer and flow

control systems:
200-500 g polymer/h
catalyst suspension;
Different reaction steps in series.

Bimodal products.
polymer suspension
Mechanical polymer properties

determination
Low raw material expenses and low
amount of residues generation in
relation with industrial Pilot Plant.
Changes in control strategy regards to

batch mode:
control of monomer consumption
in the units;
level control system
Continuous addition of solvent and
cocatalyst.
Process Description
Two reaction step with different operation
conditions (bimodal products):
Temperature
Pressure
Hydrogen/comonomers incorporation
Residence time (volume; solvent flow)
Flash step for solublized gas removal
between reaction step
Catalyst feeding to first reactor
The plant comprises:

Two 2 liters SS316 stirred autoclave reactors in series
Flash unit between reaction step
Raw material purification area
Continuous catalyst suspension addition system
Continuous cocatalyst solution feeding system
Monomer addition system with pressure control
Gas and liquid comonomers addition with gas phase composition control.
Solvent pumps
Two MicroCG for reactor gas phase analysis (one for each reactor)
Operating conditions
Maximum pressure 15 barg; operating pressure: 2-9 barg
Maximun temperature: 100C; operating temperature: 65-85C
Catalyst Addtion System

Catalyst suspension addition system for Micro Pilot Plant has to satisfy several requirements:
- accurate control of the quantity of catalyst fed,
- low flow ranges ( 0.1mg/min),
- avoiding blockage due to solid decantation,
- no inert gas addition to reactor,
- and precise control of catalyst flow independent of reactor conditions changes.
Configuration according to catalyst properties and

operation strategy.
Wide range of flow; independent of the process
conditions.
Validated system in operation conditions
Good performance in the presence of high diameter
catalyst particles and aggregations, with low mechanical
components abrasion.
Integration in ethylene consumption control loop
Polymer Suspension Transfer Systems

The instrumentation for slurry transference between unit is limited by:
Small flow ranges, 5-50ml/min (0.3-3 l/h)
Minimum diameter of pipes, valves or other elements to avoid solid blockage.
There is no comercial instrumentation for solid-liquid pumping at required flows.
Requirements for polymer slurry transference systems:
Pumping slurry against the unit pressure
Transferred volume must to keep the concentration (polymer/solvent ratio) of the reactor
Avoiding slurry sedimentations in the pipes and blockage of high size polymer particles.
Generating a nearly continuous slurry flow, avoiding process disturbances in process
conditions (pressure, level) due to transfer system.
Covering a wide range of working flows.
Allowing the integration with level control loops
Polymer Suspension Transfer Systems

Solid movement between reaction steps has been widely studied. Specific technology
has been develop for slurry transfer between units.
Transfer system behaviour

(reactor teorical concentration, 310 g PE/l C7)
Slurry concentration (gPE/l C7)
350
300
250
200
150
100
50
0
30
35
40
45
50
55
60
%vol
Agitation system 1
Agitation system 2
65
70
Control System
Temperature, pressure and composition ratio control systems are analogous to those used
in batch mode units.
Ratio Hydrogen/Ethylene R101
3.00
2.90
2.80
2.70
2.60
2.50
2.40
2.30
2.20
2.10
2.00
1.90
1.80
1.70
1.60
1.50
0
10
15
Reaction time (h)
20
25
Control System. Level Control.

Level measure in the units involves several limitations:
- Analogical measure is required
- Solvent is an hydrocarbon compound (hexane, heptane). No polar solvent.
- Polymer presence in the solvent (different slurry concentrations)
- Reactor size and connections
- Polymer growing over the walls of vessels and over inside elements.
- Variable temperature in the units
PID Eng&Techs capacitive level sensor is used in the three units. The sensibility and
the stability in this application is worse than in liquid-gas separator. Any case, it allows a
level control around 50-10% of the set point.
hydrocarbons
Control System. Ethylene consumption at reactors.

- Batch units: an established amount of catalyst is added and the response of the
system (monomer consumption) is study.

- Continuous units: the amount of polymer formed in each step must be controlled
in order to adjust percentage of the different polymer fractions in the final products.
Ethylene consumption R101 (Nml/min)
Strategies for monomer

consumption control (control
variable):
- Catalyst flow
- Residence time (solvent flow)
- Operation pressure
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
0
10
15
Reaction time (h)
20
25
Continuous Microscale Pilot Plant
Intermediate solution between traditional laboratory

research at laboratory scale and polyolefins industrial pilot
plants:
Low raw material cost compared with industrial
installations.
Operation in continuous and steady-state mode.
Bench-scale size
100-750 g/h
Scale-down continuous industrial system. The
development can be applied to different slurry
technologies (three reactors in series, etc.).
Main application: product development. Market demands
new specialized materials.
Production of enough amount of product for testing the
commercial relevance of it.
Thank you

CSTR For Fisher Tropsch

Uploaded by

Copyright:

Available Formats

CSTR For Fisher Tropsch

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CSTR For Fisher Tropsch

Uploaded by

Copyright:

Available Formats

BENCH SCALE UNITS

AND PILOT PLANTS FOR

Chemical reaction between multifunctional

Reaction does not involve low

By-product formation. Polyurethanes

Polyethylene (PE); Polypropilene (PP);

WIDE RANGE OF PROCESS AND PRODUCTS

POLYOLEFINS PRODUCTION PROCESSES

High temperature and pressure

LABORATORY EQUIPMENT FOR POLYOLEFINS

Most common laboratory

One reactor o several reactors

PRODUCTS FABRICATED BY PID Eng&Tech

Elements in Slurry Phase Polyolefins Production

MONOMER: Ethylene; Propylene

HYDROGEN (control agent of the molecular

COMONOMERS: low molecular weight

SOLVENT: heptane; hexane; isobutane

CATALYST: supported coordination catalyst

COCATALYST: catalyst activation and

Raw Material Purification

Removing potential traces of water and oxygen

Pre-purified area comprises adsorption beds in

Typical adsorbents: activated alumina; molecular

Regeneration process: high temperature and

In situ regeneration system can be included.

Laboratory Scale Batch Units

SS316 stirred autoclave reactor 500 ml to 4 l

Reactor Control Pressure.

Monomer is added continuously during the reaction

Comonomer feed lines.

Comonomers can be added like gases or liquids

Hydrogen and gas comonomers flow are

Liquid comonomers can be added by a high

Vapor-Pressure Line for Propylene

Gas Phase Composition Control

Final product properties depend of the monomer,

Hydrogen/monomer and comonomer/monomer

Gas composition can be measured at nearly real time

Result of this analysis can be integrated in the control

Nitrogen and vacuum lines are used for system

Solvent is loaded in batch mode before the

Catalyst (solid) is loaded in the beginning of

Cocatalyst (solution) is injected to solvent

Laboratory Batch Units

Polymerization reactions are complex processes.

Pilot plant for continuous polyethylene production

Micro-scale industrial process

Solid suspension transfer and flow

Different reaction steps in series.

Mechanical polymer properties

Changes in control strategy regards to

The plant comprises:

Catalyst Addtion System

Configuration according to catalyst properties and

Polymer Suspension Transfer Systems

Polymer Suspension Transfer Systems

Transfer system behaviour