Gny Pantograph Assy

www.gnyequipment.
com
April 2016
GNY 4BOTTOM TANK-TRUCK FUELING SKIDS

(JOB: FB1202) for Iceland Prime Contractor /
US Navy Airstation, Keflavik Airport, Iceland
4GNY Pantograph Assembly
4GNY Pantograph Swivel Joint

www.gnyequipment.com
GNY Pantograph Swivel Joints

(Style 20 Built-in Flanged Units)
Size: 4(100 mm) and 3(80 mm)
Model: D2000-4-SS316-PANTO and Model: D2000-3-SS316-PANTO-TTMA
Specially designed for Pantograph Assembly used in Aviation Refueling as per
MIL Spec. 15051 and STS M145.
150 psig pressure rating (working pressure) for 360 deg. rotation.
Material is Stainless Steel 316 and all other data are as per sketch.
Fitted with FOUR rows of bearing; two rows of ball bearings and two needle
roller bearings.
Ball bearing raceways are hardened (345 BHN) using a special permanent
FUSION metal hard facing process.
Fitted with triple seal design; the Main Seal is PTFE (Teflon) with Insert made
of Viton; the dust seals and 'O' ring of Viton.
Nipple (inner part) is specially dimensioned for the main seal to remain in the
proper functioning position under both positive and negative pressures.
Style 20 built-in Flanged Ends, so units can be easily changed.

'O' rings at the outer surfaces of the flanges, seal the companion flanges.
Designed to withstand temperature variations from (minus) 20 deg. to +100
deg. Centigrade.
Non-Lubricated unit, maintenance free.
Electrically Conductive and dust proof unit.
Three year warranty.
Hydro-testing and Special Testing: All Swivel Joints are Internally Hydrotested at shop before shipping. Air test, Vacuum test, Bending moment/Radial
load test, Pull load test, electrical conductivity test and Life Cycle test (US
Patented) has been conducted during the R&D (research and development)
and these tests can be conducted upon special request at extra cost.
LIFE CYCLE TESTING FOR SWIVEL JOINTS

(U.S. Patented)
SUMMARY
Current High Technology applications for swivel joints require that the
maintenance-free life expectancy of the swivel joints be accurately
known prior to deployment.
A method of establishing the operating life, including a test setup and a

procedure for determining the anticipated operating life of the swivel
joint in the field, without actually requiring the swivel joint to be used in
the field for several years, has proven to be very useful. The primary
purpose of this test setup and procedure is to qualify in advance the
appropriate materials of construction and the proper seal material for a
swivel joint given a specified operating life, for a particular application.
Based on information received from users in the field and working
knowledge obtained from field engineers for more than 30 years, various
data has been obtained as to the "average" number of swivel joint
rotations/cycles/ operations per day, working loads on the swivel joints
under various conditions, operating environments, etc. This data have
allowed parameters to be established for testing and establishing the
operating life of swivel joints in a controlled simulation test area (other
than actually being in the field).
A formal procedure has been
established, using a special test apparatus (test set-up), to determine
the operating life of swivel joints.
The user can maximize the use of a particular type of swivel joint, and
the manufacturer can develop the optimum swivel joint (after performing
tests) for a particular application. This information can also be used to
establish a product warranty or guarantee period. We maintain a
continuous life cycle analysis and laboratory testing program for various
types of swivel joints.
Page 1 of 3
INTRODUCTION
This document provides a brief description of the life cycle test for a
Pantograph Stainless Steel (SS316) Swivel Joint to certify that the Swivel Joint
has a nominal operating life greater than 10 years or 20,000 cycles of
maintenance free operation.
PURPOSE
The purpose of the life cycle test is to provide quantitative and
qualitative validation of the life expectancy for our Pantograph Swivel Joints.
The product, a Pantograph Swivel Joint is used in a pantograph assembly for
the fueling and refueling of conventional Aircraft, Jet Aircraft, and helicopters in
the aviation industry.
Product:
Pantograph Swivel Joint
Size:
3" (80 mm) and 4" (100 mm)
Body Material:
Stainless Steel 316
Seals Material:
Main Seals of PTFE with Viton Insert/

Dust Seal of Viton, and Viton `O' rings,
Bearings:
Two Ball Bearings and Two Roller Bearings
Special feature:
Both ball races are hardened up to 345 BHN.

Non-Lubricated.
LIFE CYCLE TEST PLAN

The plan for testing the swivel joints calls for continuous rotation of the swivel
joint, in two directions, clockwise and counterclockwise. The direction of
rotation is reversed periodically. Each 360 degree rotation of the Swivel joint (in
either direction) is considered a complete cycle. The test is run continuously for
a predetermined number of cycles.
Page 2 of 3
TEST PROCESS
The set-up for testing the pantograph swivel joint consists of
mounting the joint under test horizontally and rotating the joint under
simulated load conditions, with the swivel joint constantly under pressure.
The pressurized swivel joint is constantly rotated, but the direction of
rotation is reversed periodically.
The test configuration consists of a rigid test bench on which
the test swivel joint is mounted. One end of the swivel joint is attached to a
blind flange that contains pressurized fluid passing through the swivel joint.
The pressure is monitored by a pressure gauge that constantly indicates
the pressure in the swivel joint.
A calculated load is applied to the swivel joint through a load
arm that simulates load conditions that would be typically found in the field
for the particular application. The load is applied by a hydraulic jack, which
is monitored by a pressure gauge that constantly indicates the load
conditions.
The test is monitored by a stand-alone, self-contained,
microprocessor-controlled instrumentation package that allows the test
parameters to be easily modified at any time. Features incorporated in the
test process accurately identify the occurrence of predetermined
milestones. Integral safety features automatically terminated test if any test
limits are approached. The test is performed without manual intervention
and will automatically stop at the end of the pre-established test.
Life Cycle Test Setup
Page 3 of 3

Gny Pantograph Assy

Uploaded by

Copyright:

Available Formats

Gny Pantograph Assy

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Gny Pantograph Assy

Uploaded by

Copyright:

Available Formats

www.gnyequipment.

GNY 4BOTTOM TANK-TRUCK FUELING SKIDS

4GNY Pantograph Assembly

4GNY Pantograph Swivel Joint

GNY Pantograph Swivel Joints

Style 20 built-in Flanged Ends, so units can be easily changed.

LIFE CYCLE TESTING FOR SWIVEL JOINTS

A method of establishing the operating life, including a test setup and a

Pantograph Swivel Joint

3" (80 mm) and 4" (100 mm)

Stainless Steel 316

Main Seals of PTFE with Viton Insert/

Two Ball Bearings and Two Roller Bearings

Both ball races are hardened up to 345 BHN.

LIFE CYCLE TEST PLAN

Life Cycle Test Setup

You might also like