Manual de Operacion Control Rci-510 PDF

GREER COMPANY
Crane Systems
MICROGUARD
RCI 510
TELESCOPIC BOOM CRANES
MAX
TEST
23,500
44.8
62.7
i2,300
26.4
9.7Klb Ctwt
ORs Full
ERECTED 60' TELEJIB 17 o
PICK FROM MAIN BOOM
360o
AUXHD ON
FRONT WINCH
SET
OPERA
OPERATOR'S MANUAL
GREER COMPANY 1918 EAST GLENWOOD PLACE, SANTA ANA, CA 92705

RCI 510 RATED CAPACITY INDICATOR OPERATOR'S MANUAL
1 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
TABLE OF CON
CONTENTS
Introduction
Outline of Operation .....................................................................................................................4
What Does It Tell You?
The Pictograph.............................................................................................................................5
Information Screen.......................................................................................................................6
Parts-of-Line Indicator..................................................................................................................6
Operator Alarms Indicator ............................................................................................................6
Pre-Alarm Indicator ......................................................................................................................6
Overload Indicator........................................................................................................................6
Anti Two-Block Indicator ..............................................................................................................6
Bar Graph for Percentage of Rated Load ....................................................................................7
Actual Load ..................................................................................................................................7
Rated Capacity.............................................................................................................................7
Radius, Length, Angle..................................................................................................................7
What Must You Tell It?
Parts-of-Line.................................................................................................................................8
Point of Lift ...................................................................................................................................8
Auxiliary Head On or Off ..............................................................................................................8
Stowed and/or Erected Attachments ...........................................................................................8
Manual Section or Boom Mode....................................................................................................8
Jib Stowed on Boom ....................................................................................................................8
Winch ...........................................................................................................................................8
Counterweight ..............................................................................................................................8
Tires .............................................................................................................................................8
Outriggers ....................................................................................................................................8
Power Up Self-Test .................................................................................................................................9
Start-Up Screen .....................................................................................................................................10
Brightness and Contrast Controls ......................................................................................................11
System Setup
Counterweight ............................................................................................................................12
2 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
Outriggers ..................................................................................................................................13
Tires/Rigging Travel Mode .........................................................................................................14
Stowed Jibs ................................................................................................................................15
Erected Jibs ...............................................................................................................................16
Auxiliary Head ............................................................................................................................17
Choosing the Winch ...................................................................................................................18
Choosing the Point of Lift ...........................................................................................................19
Setting the Parts-of-Line ............................................................................................................20
Notes ..........................................................................................................................................21
Cancel Alarm
Push Button to Cancel Audible Alarm........................................................................................22
Reset Function Kick-Out ............................................................................................................23
Operator Settable Alarms
Accessing the Operator Alarms .................................................................................................24
Setting Minimum and/or Maximum Boom Angle........................................................................25
Setting Maximum Length, Maximum Height ..............................................................................26
Accessing Swing and Work Area Alarms...................................................................................27
Swing Alarms .............................................................................................................................28
Setting the Left and Right Swing Alarms ...................................................................................29
Work Area Selection Mode ...................................................................................................30-31
Glossary ............................................................................................................................................32-35

3 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
OUTLINE OF OP
OPERATION
SYSTEM COMPONENTS
EXTENSION SENSOR
The extension sensor provides an increasing voltage
MicroGuard Display Unit
MicroGuard Computer Unit
proportional to the extension of the boom. A cable
Pressure Transducers
attached to the boom head provides a low current
Extension Reel with length and angle sensors
Anti 2-Block (ATB) switches
PRESSURE TRANSDUCERS
Cables
Two pressure transducers measure the pressure in
Installation/Operator Manuals
the boom hoist cylinder. The resultant Total Moment
The MicroGuard RCI 510 System is intended to aid

the crane operator by continuously monitoring the
load and warning of an approach to an overload or
Two-Block condition. Crane functions are monitored
by means of high accuracy sensors. The system
continuously compares the load suspended below the
boom head with the crane capacity chart stored in the
computer memory. At approach to overload, the
system warns by means of audible and visual alarms.
The system can be configured to cause function kickout by sending a signal to function disconnect
solenoids.
DISPLAY
electrical path for the A2B signal
signal is processed to provide a continuous display of

the load suspended below the point of lift.
ANTI TWO BLOCK (A2B)
A switch monitors the approach of the hookblock or
overhaul ball to the boom head. The switch is held in
the normal position until the hookblock or overhaul
ball raises a weight that is mounted around the hoist
rope. When the weight is raised, it causes the switch
to operate. The resultant signal is sent to the
computer via the extension reel causing the A2B
alarm to operate and function kick-out to occur.
FUNCTION KICKKICK-OUT
The operator is provided with a continuous display of:
Electrically operated solenoids disconnect the control
Rated Load
lever functions for boom hoist lower, telescope out,
Actual Load
condition occurs.
Bar Graph showing Percentage of Rated Load
OPERATOR SETTABLE ALARMS
Radius of the Load
Boom Angle
Main Boom Length
means of minimum and maximum angle, maximum
Working Area
height, and/or maximum length. These alarms can be
Crane Configuration
programmed for each job site and allow the operator
On-screen messages provide the operator with visual
and winch up whenever an overload or an A2B
These alarms, when properly set by the operator,

define the operating range. This is achieved by
to work in a defined area.
warnings of conditions that occur during operation of
AREA ALARM
the system.
When set, this alarm permits the operator to define
BOOM ANGLE SENSOR
the operating zone by only two set points. The use
Boom angle is measured by means of a high-
of this method of setting results in a greatly enhanced
accuracy potentiometer/pendulum assembly that is
working area, and also clearly defines the
damped to prevent overswing. It provides a voltage
operating zone.
proportional to boom angle. The boom angle sensor is

mounted inside the cable extension reel assembly.
4 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
THE PICTOGRAPH
MANUAL SECTION
STOWED JIB
/ BOOM MODE
WINCH
JIBS
COUNTERWEIGHT
AUX HEAD
TIRES
POINT OF LIFT
OUTRIGGERS
The PICTOGRAPH gives a pictorial representation of the current setup of the system. It does this by means of light
emitting diodes (LEDs). Each shaded area contains a group of one or more LEDs and a push button that is pressed
to change the setup selection. In the groups with more than one choice or option, LEDs illuminate one at a time to
indicate the selection. The groups are shown below.
OUTRIGGERS - contain 3 LEDs. These indicate the
STOWED JIB - contains 1 LED. This will be
selection of either full outriggers, intermediate, or
illuminated when the jib is stowed on the boom.
retracted outriggers.
TIRES - contain 1 LED. When operation on tires is
selected, the outrigger LED will turn off and the tire
LED will illuminate.
COUNTERWEIGHT - contains 1 LED. It is only active
on cranes that have counterweight options.
WINCH - contains 2 LEDs. These indicate the
selection of FRONT or REAR winch.
MANUAL SECTION - contains 1 LED. It is

active on cranes that have pinned extensions or
active tip boom options.
JIBS - contain 6 LEDs. These indicate the length
and offset of the jib in use.
AUX HEAD - contains 1 LED that illuminates
when the AUX HEAD is fitted.
POINT OF LIFT - contains 3 LEDs. One will
illuminate to show the point of lift.

5 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
WHAT DOES IT TELL YOU?
6
MAX
23,500
44.8
62.7
i2,300
26.4
ORs Full
9.7Klb Ctwt
PICK FROM MAIN BOOM
TEST
2. PARTS-OF-LINE displays the parts of line

currently selected.
3. The OPERATOR ALARM lamp illuminates
when operator alarms have been set.
SET
1. The INFORMATION SCREEN contains

details of the currently selected
configuration.
360o
AUXHD ON
FRONT WINCH
5. The OVERLOAD INDICATOR (RED)

illuminates at a preset value of 100% of
Rated Capacity and provides a visual
indication of Maximum Allowed Load.
6. The ANTI TWO-BLOCK lamp illuminates
when the A2B limit switch detects approach
to a Two-Block condition.
4. The PRE-ALARM (AMBER) indicator

illuminates at a preset value of 90% of
Rated Capacity and provides a visual
indication of approach to overload.

6 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
WHAT DOES IT TELL YOU?
11
23,500
44.8
62.7
i2,300
26.4
MAX
12
9.7Klb Ctwt
ORs Full
PICK FROM MAIN BOOM
TEST
360o
AUXHD ON
FRONT WINCH
SET
10
7. The BAR GRAPH indicates the ACTUAL

LOAD as a PERCENTAGE OF RATED
CAPACITY.
8. The ACTUAL LOAD display shows total
load, including load, slings, etc. suspended
below the lifting point.
9. The RATED CAPACITY display shows the
RATED CAPACITY of the crane in the
current configuration.
11. The LENGTH display shows the length of

the main boom from the boom foot pin to the
sheave pin of the main boom head
machinery.
12. The ANGLE display indicates, in degrees,
the angle of the main boom relative to
horizontal.
10. The RADIUS display shows radius of the

load. Radius is the horizontal distance from
the centerline of rotation to the centerline of
the lifting point.
7 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
WHAT MUST YOU TELL IT?
13
MAX
TEST
15
23,500
44.8
62.7
i2,300
26.4
16
17
19
18
20
21
ORs Full
9.7Klb Ctwt
PICK FROM MAIN BOOM
360o
AUXHD ON
FRONT WINCH
22
14
13. The number of PARTS-OF-LINE.

14. POINT OF LIFT, e.g. main boom, auxiliary
head or jib.
15. AUXILIARY HEAD ON or OFF the crane.
16. Indicates JIB configuration in use.
17. MANUAL SECTION or ACTIVE TIP
extended (if applicable).
SET
19. Indicates which WINCH will be used for the

pick.
20. Indicates which COUNTERWEIGHT is fitted
(if applicable).
21. TIRES creep, static, 2 1/2 MPH, and
RIGGING/TRAVEL mode.
22. OUTRIGGERS full extension, mid
extension, or retracted.
18. JIB STOWED ON BOOM.

8 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
POWER UP SELFSELF-TEST
MAX
888;800
I88.8
I8
I88.8
888;800
I88.8
TEREX CD 225
SYSTEM SELF TEST IN PROGRESS
TEST
SET
CHART 12262-1205/20W
26
Immediately following electrical power up or following operation of the TEST switch (item 26), the system
executes a self-test that last for 8 seconds. During this time, the numerical display segments and
bar graph segments are all turned on, the audible alarm will sound, and alarm indicator lights are
illuminated.
The information display shows the crane model and rating chart number.

PN W450250 Rev B 08/09/00
TEL:(714) 259-9702 FAX:(714) 259-7626
9 of 35
GREER COMPANY
Crane Systems
START UP SCREEN
MAX
TEST
--- -
-- -
-- -
--- -
-- -
READ/UNDERSTAND THE FOLLOWING...

CIMA MANUAL,ASME/ANSI B30.5
OSHA REGS AND OPERATORS MANUAL
PRESS TO CONTINUE>
SET
27
Immediately following power up self-test, the display indications will show as above. During this time,
crane motions are disabled by the system function kickout. Operation of the bottom right information
display push button (item 27) will acknowledge the information display message and allow the system to
start normal operation.

PN W450250 Rev B 08/09/00
TEL:(714) 259-9702 FAX:(714) 259-7626
10 of 35
GREER COMPANY
Crane Systems
BRIGHTNESS AND CONTRAST CON

CONTROLS
MAX
23,500
44.8
62.7
i2,300
26.4
LED BRIGHTNESS UP
LED BRIGHTNESS DOWN
TEST
25
CONTRAST UP
SET
CONTRAST DOWN
27
Immediately following self-test and the start up screen, the information display will display a 2 second
reminder of the brightness and contrast control functions.
Push buttons to the left of the information display (item 25) allow the brightness of all LEDs on the display
panel to be adjusted up or down at any time during operation of the system unless operator alarms are
being set.
Push buttons to the right of the information display (item 27) allow the contrast of the information display
to be adjusted up or down at any time during operation of the system unless operator alarms
are being set.
During adjustment of the contrast or brightness, the information window will automatically display the
reminder window shown.

RCI 510 RATED CAPACITY INDICATOR
OPERATOR'S MANUAL
11 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
MAX
23,500
44.8
62.7
i2,300
26.4
20
SET
9,700lb Counterweight
TEST
12,000lb Counterweight
1
COUNTERWEIGHT
IF THE COUNTERWEIGHT PUSH BUTTON IS
PRESSED ON A CRANE THAT DOES NOT
HAVE COUNTERWEIGHT OPTIONS, THE
MESSAGE NO OTHER COUNTERWEIGHT
OPTIONS WILL APPEAR IN THE
INFORMATION DISPLAY. REFER TO YOUR
CRANE RATING MANUAL FOR DETAILS OF
THE OPTIONS ON YOUR CRANE
The available counterweight options will be

displayed in the information screen (item 1).
There can be four options displayed at a time,
one next to each selection key.
On cranes that have counterweight options the
operator must tell the MicroGuard System

which counterweight is currently fitted. If there
are no options, continue on to selection of
outriggers.
Start the choice by pressing the counterweight
push button (item 20).

OPERATOR'S MANUAL
12 of 35
If the required option is visible,

select the option by pressing the
button next to it.
If more than 4 options are available,

a second selection screen can be
viewed by pressing the button next
to the "next" label.
If only a single option is available, it

will automatically be selected.
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
MAX
TEST
23,500
44.8
62.7
i2,300
26.4
9.7Klb Ctwt
ORs Full
PICK FROM MAIN BOOM
360o
AUXHD ON
FRONT WINCH
SET
22
1
OUTRIGGERS
The operator must tell the system which

outrigger position is in use.
Start the choice by pressing the outrigger

The outrigger selection will automatically

move on to the next selection.
EXAMPLE:
From fully extended to half extended, or
from half-extended to fully retracted and
then back to fully extended with each push
of the button. If no other selections are
available, the message "No other chassis
options" will appear on the information
screen (item 1).

OPERATOR'S MANUAL
13 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
MAX
23,500
44.8
62.7
i2,300
26.4
TEST
SET
RIGGING/TRAVEL
TIRES, 2.5MPH, FRONT

STATIONARY
21
1
TIRES/RIGGING TRAVEL
There can be four options displayed at a

time, one next to each selection key.
IF THE TIRE PUSH BUTTON IS PRESSED ON

A CRANE THAT DOES NOT HAVE TIRE
OPTIONS THE MESSAGE NO OTHER TIRE
OPTIONS WILL APPEAR IN THE
THE OPTIONS ON YOUR CRANE.
On cranes that have more than one tire

option, e.g. static, creep etc., the operator
must select the tire configuration that
corresponds to the tire chart to be used.
Start the choice by pressing the tire push

button (item 21).
The available tire selection options will be


button next to it.


RIGGING/TRAVEL MODE is selected when

the crane is in the rigging process or is a
rough terrain crane traveling between jobs.
DO NOT PERFORM CRANE LIFTING OPERATIONS WHILE
WARNING
THE RIGGING/TRAVEL MODE IS SELECTED.

ALL CRANE CONTROLS REMAIN ACTIVE WHILE THE
RIGGING/TRAVEL MODE IS SELECTED.

OPERATOR'S MANUAL
14 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
18
MAX
23,500
44.8
62.7
i2,300
26.4
SET
NO STOWED JIB
TEST
60' TELEJIB STOWED
1
STOWED JIBS
IF THE STOWED JIB PUSH BUTTON IS
HAVE JIB OPTIONS, THE MESSAGE NO
OTHER STOWED OPTIONS WILL APPEAR
IN THE INFORMATION DISPLAY. REFER TO
YOUR CRANE RATING MANUAL FOR
DETAILS OF THE OPTIONS ON YOUR
CRANE.
On cranes that have more than one jib

option (fixed, offset, or telejib etc.), the
operator must select the jib to be used.
Start the choice by pressing the stowed jib

The available stowed jib options will be

There can be four options displayed at a
time, one next to each selection key.

OPERATOR'S MANUAL
15 of 35

button next to it.


PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
16
MAX
23,500
44.8
62.7
i2,300
26.4
38' JIB@17degs
38' JIB@2degs
TEST
38' JIB@30degs
SET
MORE >
1
ERECTED JIBS
IF THE ERECTED JIB PUSH BUTTON IS
HAVE JIB OPTIONS, THE MESSAGE NO
OTHER JIB OPTIONS WILL APPEAR IN THE
THE OPTIONS ON YOUR CRANE.
There can be four options displayed at a time,

one next to each selection key.
To erect a JIB, it must first have been

selected and stowed as detailed on the
previous page.
Start the choice by pressing the erected jib

The available erected jib options will be


OPERATOR'S MANUAL
16 of 35

button next to it.


PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
15
MAX
TEST
23,500
44.8
62.7
i2,300
26.4
9.7Klb Ctwt
ORs Full
PICK FROM MAIN BOOM
360o
AUXHD ON
FRONT WINCH
SET
1
AUXILIARY HEAD
IF THE AUXILIARY HEAD PUSH BUTTON IS
HAVE AN AUXILIARY HEAD, THE MESSAGE
NO OTHER AUXILIARY HEAD OPTIONS
WILL APPEAR IN THE INFORMATION
SCREEN (ITEM 1).
An auxiliary head fitted on a crane must be

included in the crane setup.
To set up the crane with an auxiliary head, press
the auxiliary head push button, (item 15).
This will toggle the auxiliary head on and off
each time the button is pressed.

OPERATOR'S MANUAL
17 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
19
MAX
TEST
23,500
44.8
62.7
i2,300
26.4
ORs Full
9.7Klb Ctwt
PICK FROM MAIN BOOM
360o
AUXHD ON
FRONT WINCH
SET
1
CHOOSING THE WINCH
For cranes with two winches, always select the winch to be used for the lift before selecting the point of lift
and parts of line. The system stores point of lift and parts of line selections for each winch.
Choose the winch to be used by pressing

the winch push button (item 19).
This toggles between the two available

winches each time the button is pressed.
If no other winch is available, the message
"No other winch options" will appear for
three seconds on the information screen
(item 1).

OPERATOR'S MANUAL
18 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
14
MAX
TEST
23,500
44.8
62.7
i2,300
26.4
ORs Full
9.7Klb Ctwt
PICK FROM MAIN BOOM
360o
AUXHD ON
FRONT WINCH
SET
1
CHOOSING THE POINT OF LIFT
Before choosing the point of lift, check that the correct winch has been selected.
Always check the point of lift selection following selection of the winch.
Choose the point of lift to be either from the

main boom, auxiliary head, or jib by pressing
the point of lift push button (item 14).
This action moves the selected lifting point
to the next available lifting point, i.e. from jib
to aux head, from aux head to main boom,
and from main boom back to jib again.
If an option is not available, it will be

skipped over.
If no other pick point options are

available, the message "No other pick
point options" will be displayed on the
information screen (item 1).

OPERATOR'S MANUAL
19 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
13
MAX
TEST
23,500
44.8
62.7
i2,300
26.4
9.7Klb Ctwt
ORs Full
PICK FROM MAIN BOOM
360o
AUXHD ON
FRONT WINCH
SET
SETTING THE PARTSPARTS-OFOF-LINE

Always check and select parts-of-line following selection of the winch and point of lift.
Set the PARTS-OF-LINE for the currently

selected winch by pressing the UP or
DOWN arrow, as appropriate. (item 13).
When another winch is selected, it may be

necessary to reset the parts-of-line for the
other winch.
The number of parts-of-line will appear in

the parts-of-line display (item 13).
When the number of parts in the parts-ofline on the crane is changed, it will be
necessary to reset the parts-of-line on the
display.

OPERATOR'S MANUAL
20 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SYSTEM SETUP
MAX
23,500
44.8
62.7
i2,300
26.4
ORs Full
9.7Klb Ctwt
PICK FROM MAIN BOOM
TEST
360o
AUXHD ON
FRONT WINCH
SET
NOTES
The system has the capability of remembering all of the configuration data
previously set. After removing power to the system and then powering up again,
the settings remain intact until reset by the operator.
After the configuration has been set, the operation of the System
depends only upon setting which winch is in use. Changing the winch
will automatically change the lifting point and the parts-of-line to the
values previously set for the selected winch. Always check the point of
lift and parts-of-line following selection of the winch.

OPERATOR'S MANUAL
21 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
CANCEL AUDIBLE ALARM
MAX
23,500
44.8
62.7
i2,300
26.4
9.7Klb Ctwt
ORs Full
PICK FROM MAIN BOOM
TEST
360o
AUXHD ON
FRONT WINCH
SET
23
PUSH BUTTON TO CANCEL AUDIBLE ALARM
The cancel alarm push button (item 23) is
used to silence the audible alarm. Pressing this
button once will cancel an audible alarm that
has occurred as a result of an:
Overload
A2B Alarm
Operator Settable Alarm
The audible alarm remains canceled until the
condition that caused the alarm has been
removed. See page 23.
EXAMPLES:
AFTER CANCELING AN AUDIBLE ALARM:
If the audible alarm sounded because of an

overload condition, the alarm will remain
canceled until the condition is corrected.
If another alarm condition occurs that

normally causes an alarm to sound (such
as A2B) or if a previous condition
(such as overload) is removed and then

recurs, the new alarm condition will cause
the audible alarm to sound again.
The CANCEL ALARM push button is also used
to reset the function kick-out relay when it is
necessary to bypass the function disconnects.
Examples of when it may be necessary to
override a function disconnect condition are:
If the boom hoist cylinder is fully extended, the
pressure in it will rise. This will be seen by the
system as an overload and will not allow the
operator to boom down. Using the bypass is
necessary in this situation to move away from
the fully extended boom hoist cylinder position.

OPERATOR'S MANUAL
22 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
CANCEL AUDIBLE ALARM

M AX
2 3 ,5 0 0
4 4 .8
6 2 .7
i2 ,3 0 0
2 6 .4
9.7Klb Ctwt
ORs Full
ERECTED 60' T ELEJI B 17 o
PICK FROM MAIN BOOM
TEST
CONTINUED
360o
AUXHD ON
FRONT WINCH
SET
23
RESET FUNCTION KICKKICK-OUT
When the crane is to be rigged, it is often
necessary to put the boom in a position that
could cause function kick-out. Using the bypass
is necessary in this situation.
Press and release and then press and hold
the CANCEL ALARM push button (item 23)
for approximately 5 seconds to reset the
relay. At this time a second beep is heard
confirming the bypass. When the condition
that caused the alarm is no longer present,
the function disconnect relay will reset to the
normal condition. Should a different alarm
condition occur while the relay is overridden, the new alarm condition will cause
the controls to disconnect again.
WHEN THE FUNCTION DISCONNECT RELAY

IS RESET BY MEANS OF THE CANCEL
ALARM PUSH BUTTON, THERE IS NO
LONGER PROTECTION AGAINST THE
CONDITION THAT CAUSED THE FUNCTION
KICK-OUT.

WARNING
OPERATOR'S MANUAL
23 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
MAX
23,500
44.8
62.7
i2,300
26.4
MIN ANGLE
TEST
28
OFF
MAX ANGLE OFF
MAX LENGTH OFF
MAX HEIGHT OFF
25
SET
29 24
27
ACCESSING THE OPERATOR ALARMS

To access the Operator Alarms from the main
working screen, press the operator alarms push
button (item 24). The Information Screen will
then show the current status of the alarms.
The four operator alarms are shown below
followed by the number identity of the push
button that controls each alarm. These buttons
are called out in the illustration above.
Minimum Boom Angle (item 28)
Each push button operates as a toggle switch

turning the alarm "ON" or "OFF."
To activate or deactivate an alarm:
If the alarm is OFF, press the
appropriate push button to turn the
alarm ON.
If the alarm is ON, press the
appropriate push button to turn the
alarm OFF.
Refer to page 25 for a discussion on minimum
and maximum boom angles and page 26 for
maximum boom length and maximum tip height.
Maximum Boom Angle (item 29)

Maximum Boom Length (item 25)
Maximum Tip Height (item 27)
Return to the main screen by pressing the

operator alarm push button (item 24) two
times.

OPERATOR'S MANUAL
24 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
MAX
23,500
44.8
62.7
i2,300
26.4
MIN ANGLE
TEST
32.0
MAX ANGLE 67.0
MAX LENGTH OFF
29
Move the boom to the desired minimum angle

(in this example 32).
Press the operator alarm push button (item 24)
to access the operator alarm screen.
Press the push button (item 28) pointing to Min
Angle. In this example the display will read
MIN ANGLE 32.
The red warning light (item 5) will flash and the
audible alarm will sound whenever the boom
angle is below 32.
Pressing the MIN ANGLE push button again will
cancel the alarm and the display will read
MIN ANGLE OFF
OPERATOR'S MANUAL
25 of 35
24
SETTING MAXIMUM BOOM ANGLE ALARM
Move the boom to the desired maximum

angle (in this example 67).
Press the operator alarm push button (item

24) to access the operator alarm screen.
Press the push button (item 29) pointing to

Max Angle. In this example the display will
read MAX ANGLE 67.
The red warning light (item 5) will flash and

the audible alarm will sound whenever the
boom angle is above 67.
Pressing the MAX ANGLE push button
again will cancel the alarm and the display
will read MAX ANGLE OFF.

SET
MAX HEIGHT OFF
28
SETTING MINIMUM BOOM AN
ANGLE ALARM
CONTINUED
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
CONTINUED
MAX
23,500
44.8
62.7
i2,300
26.4
MIN ANGLE
TEST
OFF
MAX ANGLE OFF
MAX LENGTH 58.0
SET
MAX HEIGHT 78.0
25
27
24
SETTING
LENGTH
H ALARM
SETTING MAXIMUM BOOM LENGT
SETTING MAXIMUM TIP HEIGHT ALARM

length, in this example 58 ft.
Max Length. In this example the display will
read MAX LENGTH 58 FT.
boom length exceeds 58 ft.
Pressing the MAX LENGTH push button again
will cancel the alarm and the display will read
MAX LENGTH OFF.

height, in this example 78 ft.
Max Height. In this example the display will
read MAX HEIGHT 78 FT.
boom tip height exceeds 78 ft.
Pressing the MAX HEIGHT push button again

will cancel the alarm and the display will read
MAX HEIGHT OFF.

OPERATOR'S MANUAL
26 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
OPERATOR SETTABLE ALARMS CONTINUED
MAX
TEST
28
23,500
44.8
62.7
i2,300
26.4
LEFT SWING OFF
RIGHT SWING OFF
LEFT POINT OFF
RIGHT POINT OFF
SET
29
25
27
ACCESSING SWING AND

WORK AREA ALARMS
24
To access the SWING AND WORK AREA

ALARMS from the main working screen, press
the OPERATOR ALARM push button (item 24)
2 times.
Each push button operates as a toggle switch. If

the alarm to be set is OFF, pressing the push
button will turn the alarm ON. If the alarm to be
set is ON pressing the push button will turn the
alarm OFF.
The Information Screen will show the current

status of the Swing and Work Area Alarms.
When Operator Alarms are set, the light in the

push button (item 24) will be illuminated.
There are 4 separate operator alarms, all

controlled by push buttons (items 25, 27, 28,
and 29). Each one of these push buttons relates
to the alarm to which it points.
Return to the main screen by pressing the

OPERATOR ALARM push button (24).

OPERATOR'S MANUAL
27 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
CONTINUED
SWING ALARMS
These alarms, when set, permit the operator to define a Working Arc and an Exclusion Zone by two set
points. The following diagram illustrates the Working Arc and Exclusion Zone.
WORKING ARC AND EXCLUSION ZONE

Right Swing
A left swing alarm is activated when

swinging to the left.
WORKING ARC
Left Swing
A right swing alarm is activated when

swinging to the right
EXCLUSION ZONE
In this example, the working arc is the

smaller piece of the pie.
WORKING ARC AND EXCLUSION ZONE
A left swing alarm is activated when

swinging to the left.
Left Swing
EXCLUSION ZONE
A right swing alarm is activated when

swinging to the right
Right Swing
In this example, the working arc is the larger

piece of the pie.
WORKING ARC
WARNING
THE OPERATOR DEFINED SWING ALARM IS A WARNING DEVICE. ALL FUNCTIONS REMAIN OPERATIONAL WHEN ENTERING THE OPERATOR DEFINED EXCLUSION ZONE. IT IS THE RESPONSIBILITY OF
THE OPERATOR TO SET SWING ALARMS THAT ENSURE THAT THE CRANES BOOM, ATTACHMENT,
LOAD, AND RIGGING ETC. MAINTAINS A SAFE WORKING DISTANCE FROM THE OBSTACLE. AVOID POSITIONING THE BOOM, ATTACHMENT, LOAD, AND RIGGING ETC. IN THE EXCLUSION ZONE WHEN MOVING
TO THE LEFT AND RIGHT SWING POINTS. WHEN SELECTING LEFT AND RIGHT SWING POINTS ENSURE
THAT THE LOAD WILL MAINTAIN A SAFE DISTANCE FROM THE OBSTACLE. IF THE CRANE OR OBSTACLE
IS MOVED OR IF A DIFFERENT SIZE LOAD IS LIFTED THE SWING ALARMS MUST BE RESET.
OPERATOR'S MANUAL
28 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
OPERATOR
CONTINUED
MAX
TEST
23,500
44.8
62.7
i2,300
26.4
LEFT SWING
325 0
RIGHT SWING
LEFT POINT OFF
SET
RIGHT POINT OFF
28
35 0
29
24
SETTING LEFT SWING A

ALARM
LARM
SETTING RIGHT SWING ALARM
Move the boom to the desired Right Swing

Limit, e.g. 35.
Press the Right Swing push button (item

29). The information screen (item 1) will
read RIGHT SWING 35.
Swing the boom to the desired Left Swing

Limit, e.g. 325.
24) 2 times to access the swing alarm
screen.
Left Swing. The information screen (item 1)
will read LEFT SWING 325.
Both Left and Right Swing Alarms must be set

for the system to operate correctly. The red
warning light (item 5) will flash and the audible
alarm will sound whenever only one of the
left/right swing limits is set.

audible alarm will sound whenever the boom
swings past the preset limits.
Pressing the LEFT SWING and RIGHT SWING
push buttons again will cancel the alarm and the
information screen (item 1) will read:
LEFT SWING OFF RIGHT SWING OFF.

OPERATOR'S MANUAL
29 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
CONTINUED
WORK AREA SELECTION MODE

This alarm, when set, permits the operator to define an Operating Zone by only two set points. The use of
this method results in a greatly enhanced work area and also clearly and simply defines the Exclusion
Zone area. The following diagram illustrates the Operating Zone and the Exclusion Zone.
Operator Area Alarm and Operating Zones
Operating Zone
Operating Zone
Set Point 2
Operating Zone
Safe
Working
Distance
Set Point 1
EXCLUSION ZONE
OBSTACLE
Obstacle
EXCLUSION ZONE
The operator defined work area alarm, when set, will define an imaginary vertical plane between two set
points to optimize the working area. When passing the plane, the red warning lamp will illuminate, the
audio alarm will sound, and the message EXCLUSION ZONE will flash on the display.
WARNING
THE OPERATOR DEFINED WORK AREA ALARM IS A WARNING DEVICE. ALL FUNCTIONS REMAIN OPERATIONAL WHEN
ENTERING THE OPERATOR DEFINED EXCLUSION ZONE. SAFE WORKING DISTANCE IS THE TIME IT WOULD TAKE AN
OPERATOR TO REACT TO AN ALARM AND FOR THE CRANE MOTION TO BE HALTED BEFORE ENTERING THE EXCLUSION ZONE. IT IS THE RESPONSIBILITY OF THE OPERATOR TO SET POINTS THAT ENSURE THAT THE CRANE BOOM,
ATTACHMENT, LOAD, RIGGING, ETC. MAINTAINS A SAFE WORKING DISTANCE FROM THE OBSTACLE. AVOID
POSITIONING THE BOOM, ATTACHMENT, LOAD, RIGGING, ETC. IN THE EXCLUSION ZONE WHEN MOVING TO SET
POINTS 1 AND 2. WHEN SELECTING SET POINTS 1 AND 2, ENSURE THAT THE LOAD WILL MAINTAIN A SAFE DISTANCE
FROM THE OBSTACLE. IF THE CRANE OR OBSTACLE IS MOVED, OR IF A DIFFERENT SIZE LOAD IS LIFTED, THE WORK
AREA ALARM MUST BE RESET.
OPERATOR'S MANUAL
30 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
CONTINUED
M AX
TES T
2 3 ,5 0 0
4 4 .8
6 2 .7
i2 ,3 0 0
2 6 .4
LEFT SWING OFF
RIGHT SWING OFF
LEFT POINT SET
RIGHT POINT SET
25
27
SE T
24
WORK AREA SELECTION MODE

24) two times to access the Work Area
alarm screen.
SETTING POINTS 1 AND 2
Move the boom, attachment, load, rigging

etc. to the desired LEFT SET POINT.
Left Point. The information screen (item 1)
will read LEFT POINT SET.
Both Left and Right Points must be set for the

system to operate correctly. The red warning
light (item 5) will flash and the audible alarm will
sound whenever only one of the left/right swing
limits is set.
Move the boom, attachment, load, rigging

etc. to the desired RIGHT SET POINT.

Right Point. The information screen (item 1)
will read RIGHT POINT SET.

audible alarm will sound whenever the boom tip
penetrates the exclusion zone.
Pressing the LEFT POINT and RIGHT POINT
push buttons (items 25 & 27) again will cancel
the alarm and the information screen (item 1)
will read
LEFT POINT OFF

OPERATOR'S MANUAL
31 of 35
RIGHT POINT OFF
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
GLOSSARY OF TERMS
ACTUAL LOAD
The load suspended below the lifting point.
ALARM
A signal that warns or alerts, such as a flashing light or loud noise.
ANGLE SENSOR
A device that measures the inclination of a boom.
ANTI TWO-BLOCK
A device that, when activated, prevents movement that causes twoblocking.
AUDIBLE ALARM
A signal that alerts by means of noise.
AUXILIARY HEAD
(AUXHD)
A short jib fitted at the main boom head that is used to provide
separation of the main and auxiliary ropes when both are reeved over the
main boom head.
AUXILIARY HOIST
(AUX HOIST)
A separate hoist rope system other than the main hoist.
BARGRAPH
A pictorial device used to illustrate quantitative relationships.
BOOM
A member hinged to the upperstructure that supports the hoisting tackle.
BOOM ANGLE
The angle of the longitudinal axis of the boom relative to horizontal.
BOOM HOIST
A device for controlling the boom angle.
BOOM LENGTH
The length of the boom along its longitudinal axis from the foot pin to the
axle of the head machinery.
BOOM MOMENT
The turning moment around the boom pivot caused by the moment of the
unladen boom.
CAPACITY CHART
A table showing the rating of a crane.
CENTER LINE OF
ROTATION
The vertical axis around which the crane upperstructure rotates.
CENTER OF GRAVITY
The point at which the entire weight of a body may be considered as concentrated so that if supported at this point the body would remain in equilibrium in any position.
COMMISSIONING
Preparing to be put into service.
CONFIGURATION
An arrangement of the lifting elements of a crane.

OPERATOR'S MANUAL
32 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
COUNTERWEIGHT
(CTWT)
A weight used to supplement the weight of the crane to provide

stability for lifting.
CURSOR
A pointer on a display that indicates the position where data is to be

entered.
DEDUCT
A reduction in rated capacity for an unused stowed or erected

attachment.
DIRECTION
The direction of rotation of the superstructure.
DUTY
A working configuration on a crane usually contained in a single column of a

capacity chart.
ERECTED ATTACHMENT
An attachment on the main boom fitted in its working position.
EXTENSION SENSOR
A device that measures the extension of the telescoping sections of a boom.
FUNCTION KICK-OUT
A device that disengages certain crane functions whose movement could

cause overload or two-blocking.
HEIGHT
The vertical distance from the ground to the tip of the boom or attachment.
HORIZONTAL
Parallel to the horizon.
INFORMATION SCREEN
A display that gives information supplemental to the information on the

pictograph.
INTEGRATED CIRCUITS
A tiny complex of electronic components and connections on a small slice of

material (such as silicon).
JIB
Something attached such as a lattice fly or jib on a crane boom.
MANUAL SECTION
The tip section of the main boom that can be telescoped independently of
the other sections.
MICROPROCESSOR
A computer processor contained on an integrated chip.
MOMENT
The product of force and distance to a particular axis or point.
OPERATOR ALARMS
Alarms that can be set by the operator, which provide working limits
additional to the chart limits.
OUT OF DUTY
A point which is either longer than the longest permitted radius or lower than
the lowest permitted angle on a capacity chart

OPERATOR'S MANUAL
33 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
OUTRIGGER (ORs)
A support projecting from a main structure used to provide additional

stability.
OVERLOAD
The point at which the actual load exceeds the rated capacity of the crane.
PARTS OF LINE
The number of parts of hoist rope between the upper and lower blocks.
PICTOGRAPH
A pictorial representation of the crane.
POINT OF LIFT
The location of the hoist rope for the current lift e.g. main boom, auxiliary
head or jib.
PRE-ALARM
The point at which the actual load is 90% of the rated capacity of the crane.
PRESSURE
Hydraulic pressure in the boom hoist cylinder
RADIUS
The horizontal distance from the centerline of rotation to the center of the
hook.
RATED CAPACITY
The lifting capacity of a crane, as determined by the published capacity

chart.
RATED CAPACITY
The load that a crane can safely handle based on factors such as strength,
stability, and rating.
RATING
A factor determined by legislation that limits the proportion of the

capability of the cranes that may be utilized in a lifting operation.
Usually expressed as a percentage of strength or stability.
REEVING
A rope system in which the rope travels around drums and sheaves.
ROPE LIMIT
The maximum permitted single line pull determined by the construction and
diameter of a wire rope.
ROPE LIMIT
A condition that occurs when the type of rope and the parts-ofline in use
restrict the capacity of the crane.
SENSOR
A device that responds to physical stimulus and transmits a resulting

impulse.
SHEAVE
A grooved wheel or pulley.
SLEW OFFSET
The horizontal distance from the boom pivot to the center of rotation
STOWED ATTACHMENT
An attachment usually stowed on the main boom when not in use.
UPPERSTRUCTURE
The structural part of a crane above the carrier, usually rotating.

OPERATOR'S MANUAL
34 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626
GREER COMPANY
Crane Systems
SWING
The rotation of a crane upper around its center line.
SWING ALARMS
Audible alarms occurring when the upper structure swings into areas
defined by the operator with the use of Operator Alarms.
SWL (%SWL)
Percentage of safe working load. The proportion of the crane capacity which
is being utilized at any one time expressed as a percentage of rated
capacity
TRANSDUCER
A device that is actuated by energy from one system and converts this to
another form for use by a different system (as a loudspeaker, that is,
actuated by electrical signals and supplies acoustic power).
TWO-BLOCKING
The condition when the lower load block or hook assembly comes in contact
with the upper load block or boom point.
UNLADEN
A boom that has no additional stowed or erected attachments and that is not
supporting a load.
WINCH
A hoist drum used in conjunction with a rope for raising and lowering loads.
WORK AREA ALARM
Permits the operator to define an operating zone by the means of only two
set points.

OPERATOR'S MANUAL
35 of 35
PN W450250 Rev B 08/09/00

TEL:(714) 259-9702 FAX:(714) 259-7626

Manual de Operacion Control Rci-510 PDF

Uploaded by

Copyright:

Available Formats

Manual de Operacion Control Rci-510 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual de Operacion Control Rci-510 PDF

Uploaded by

Copyright:

Available Formats

What is the RCI 510 rated capacity indicator used for?

What is the RCI 510 rated capacity indicator used for?

What information does the RCI 510 display?

What information does the RCI 510 display?

GREER COMPANY

TELESCOPIC BOOM CRANES

GREER COMPANY 1918 EAST GLENWOOD PLACE, SANTA ANA, CA 92705

PN W450250 Rev B 08/09/00

PN W450250 Rev B 08/09/00

GREER COMPANY 1918 EAST GLENWOOD PLACE, SANTA ANA, CA 92705

PN W450250 Rev B 08/09/00

The extension sensor provides an increasing voltage

MicroGuard Display Unit

MicroGuard Computer Unit

proportional to the extension of the boom. A cable

attached to the boom head provides a low current

Extension Reel with length and angle sensors

Anti 2-Block (ATB) switches

Two pressure transducers measure the pressure in

the boom hoist cylinder. The resultant Total Moment

The MicroGuard RCI 510 System is intended to aid

electrical path for the A2B signal

signal is processed to provide a continuous display of

The operator is provided with a continuous display of:

Electrically operated solenoids disconnect the control

lever functions for boom hoist lower, telescope out,

Bar Graph showing Percentage of Rated Load

OPERATOR SETTABLE ALARMS

Radius of the Load

Main Boom Length

means of minimum and maximum angle, maximum

height, and/or maximum length. These alarms can be

programmed for each job site and allow the operator

On-screen messages provide the operator with visual

and winch up whenever an overload or an A2B

These alarms, when properly set by the operator,

to work in a defined area.

warnings of conditions that occur during operation of

When set, this alarm permits the operator to define

BOOM ANGLE SENSOR

the operating zone by only two set points. The use

Boom angle is measured by means of a high-

of this method of setting results in a greatly enhanced

accuracy potentiometer/pendulum assembly that is

working area, and also clearly defines the

damped to prevent overswing. It provides a voltage

proportional to boom angle. The boom angle sensor is

PN W450250 Rev B 08/09/00

STOWED JIB - contains 1 LED. This will be

selection of either full outriggers, intermediate, or

illuminated when the jib is stowed on the boom.

MANUAL SECTION - contains 1 LED. It is

GREER COMPANY 1918 EAST GLENWOOD PLACE, SANTA ANA, CA 92705

PN W450250 Rev B 08/09/00

2. PARTS-OF-LINE displays the parts of line

1. The INFORMATION SCREEN contains

5. The OVERLOAD INDICATOR (RED)

4. The PRE-ALARM (AMBER) indicator

GREER COMPANY 1918 EAST GLENWOOD PLACE, SANTA ANA, CA 92705