Scribd
Upload
44 views

EN1740 Computer Aided Visualization and Design: Spring 2012

The document discusses a computer aided visualization and design class. It summarizes the topics covered in the previous lecture, including shared data and component operations. The current lecture will cover an introduction to top-down design, including fundamentals and using skeletons. Students are instructed to download AutoCAD in preparation for upcoming lectures on the software. Guidelines are provided for an upcoming project drawing, including tips on dimensions, formatting and hiding features. Finally, the differences between top-down and bottom-up design approaches are explained, with benefits and drawbacks of each method discussed.

Uploaded by

sandeshbhavsar
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
44 views

EN1740 Computer Aided Visualization and Design: Spring 2012

The document discusses a computer aided visualization and design class. It summarizes the topics covered in the previous lecture, including shared data and component operations. The current lecture will cover an introduction to top-down design, including fundamentals and using skeletons. Students are instructed to download AutoCAD in preparation for upcoming lectures on the software. Guidelines are provided for an upcoming project drawing, including tips on dimensions, formatting and hiding features. Finally, the differences between top-down and bottom-up design approaches are explained, with benefits and drawbacks of each method discussed.

Uploaded by

sandeshbhavsar
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 37

EN1740 Computer Aided Visualization

and Design
Spring 2012
3/20/2012
Brian C. P. Burke

BCB Mar. 20, 2012

EN1740, S2012

Last Time:

Tonight:

Shared data

Intro to Top-Down Design

Copied Geometry

Fundamentals

Component Operations

Skeletons

Family Tables

BCB Mar. 20, 2012

EN1740, S2012

AutoCAD Next Up
Were going to tackle an introduction to AutoCAD in the next few lectures
Please go to Autodesks educational community site and register
www.Autodesk.com/edcommunity
Once registered youll be able to download AutoCAD 2012

Please do so in anticipation of the lectures to come

BCB Mar. 20, 2012

EN1740, S2012

Drawing Tips for Project


Things To Keep In Mind:
Cross-sections
Need a SINGLE LETTER name
Must be accompanied by section arrows
Dont leave dimension on the object
Provide good spacing for the dimensions
Dont cross dimension and extension lines
Dont leave geometry shaded on drawing (perspective view included)
Make sure you use a drawing format (title block)
Include appropriate note for CTFD (provided on supporting page)
DONT double dimension
HIDE DATUM FEATURES ON DRAWING!!
BCB Mar. 20, 2012

EN1740, S2012

Top-Down vs. Bottom-Up


Lets say you wanted to design this.

http://allworldcars.com/wordpress/?p=2208

BCB Mar. 20, 2012

EN1740, S2012

Top-Down vs. Bottom-Up


Top-Down would start with this..

then figure out what would fit, then place the


engine, bumpers wheels, etc.

BCB Mar. 20, 2012

EN1740, S2012

Top-Down vs. Bottom-Up


Bottom-up would start with this stuff..

and start putting them together

BCB Mar. 20, 2012

EN1740, S2012

Top-Down vs. Bottom-Up


Top-Down:

Bottom-Up:

Benefits

Benefits

Product needs to be fairly well


defined, so youre starting with the
answer

Does not need well defined


structure to start

Facilitates large assemblies well


Very effective way to work in
cross-functional groups
Drawbacks:
Limits flexibility

Very flexible
Drawbacks:
Team needs to communicate more
frequently
Can get unwieldy in large
assemblies

Must have team buy-in


Real World is going to be a mix of these philosophies

BCB Mar. 20, 2012

EN1740, S2012

Top-Down Tools
There are a number of tools available to manage and facilitate top down design
Skeletons
Data sharing
Published
Copied
Component operations Merge, Cut
Simplified reps
Shrink Wrap
Many others

BCB Mar. 20, 2012

EN1740, S2012

Skeletons
Skeletons provide:
Product layout and envelope
Components interface locations and size
Product volume
Connections and mechanisms

BCB Mar. 20, 2012

EN1740, S2012

Skeletons Theres a lot of rules


FROM THE PRO/E MANUAL:
Before creating a skeleton model, consider the following points:
Only one motion skeleton can be created or inserted in an assembly.
Multiple standard skeletons can be created in an assembly when the
multiple_skeletons_allowed configuration option is set to yes.
A skeleton model is similar to any other assembly component. It has features, layers,
relations, views, bodies, and so on.
External reference control settings can be used to restrict geometry and assembly
placement references to skeleton models only (Edit > Setup > Ref Control > Skeleton
Model). These options control references for all skeletons in the assembly.
Skeleton models can maintain their own family tables. This means that assemblies can
maintain different skeleton instances across a family table.
All simplified representation functionality available in Part and Assembly mode is available
for skeleton models (beginning with Pro/ENGINEER 2001).
Skeleton models can be selected By Rule when managing simplified representations.

BCB Mar. 20, 2012

EN1740, S2012

Skeletons
In the end, Skeletons are pretty simple

A Skeleton can be any part comprised of datum planes, axes and


curves that define a product
If created as a standard part, Skeleton rules wont apply
This may not be all bad

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Well illustrate the use of Top-Down tools with a relatively simple product

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Begin by creating a skeleton
Create a new
assembly > grinder.asm
Insert > Component >
Create
From Component
Create dialog Select
Skeleton Model
From Creation Options
Select Empty

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Notice in the Model Tree the
addition of the Skeleton as the
first feature
Skeletons are always
first
Right Click on the Skeleton
and open it

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create default datums
Click create
datum plane icon
to create default
datums
Click create
coordinate system
Select DTM1,
DTM2, DTM 3 in
order as
references

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create a sketch to scale skeleton
Create a Sketch
Select DTM3 as
Front
Sketch a T as shown
6H X 3.56W

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create layout datums
Create an Axis normal to
DTM3 and offset 4.5in
from DTM2
Rename axis as CAP

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create layout datums (cont.)
Create an Axis normal to
DTM2 and offset .75in
from DTM1
Rename axis as
MOTOR

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create layout datums (cont.)
Repeat the process twice
more to locate two AA batteries
Normal to DTM2, offset
from DTM1 & DTM3
1.5in and .58in,
respectfully
Rename axes BATT1 and
BATT2

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create layout datums (cont.)
Create a datum plane
through CAP axis and at a
-10deg angle to DTM2
Rename plane
CAP_PLANE

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create layout datums (cont.)
Create a datum plane
offset .375 from DTM2
Rename plane
BATT_COVER

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools

Model Tree for Skeleton


should look like this when
done

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
File > New Part >
grinder_ID.prt
Insert > Shared Data >
Copy Geometry
Turn off Published
geometry only
Select grinder_skel.prt
as reference part
OK for Default CSYS

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
In Copy geometry
dashboard, click in
References selection
Select the CAP_PLANE
and BATT_COVER datum
plane

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Extrude an Ellipse from the
TOP datum plane
Ry=1.53, Rx=1.78, 6in H
Choose Capped ends under
Options

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Sketch a straight curve aligned
with CAP_PLANE datum
Sketch a straight curve aligned
with BATT_COVER

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Sketch latch spine

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Merge surfaces together

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Add R.250 radius

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
All other radii R.060

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Project sketched curves
onto surface
Select curve
Edit > Projected
Select all intersected
surfaces

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Repeat for bottom curve

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Cut surface with Trim
Select surfaces
Edit > Trim
Toggle through until
keep both sides is
selected

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
The reason for a separate
ID modelmost Industrial
Designer want to see the
whole product while
designing

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Insert a copy of the base
surface feature into the tree,
just after its created.

BCB Mar. 20, 2012

EN1740, S2012

EXERCISE Top-Down Design Tools


Create an Industrial Design model
Heres the ID model

BCB Mar. 20, 2012

EN1740, S2012

You might also like