ATV 312 Quick Start

Quick Start Guide - ATV312
ENGLISH
S1A1094202
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Read and understand this quick start guide before performing any procedure with this drive.
The user is responsible for compliance with all international and national electrical code requirements with respect to grounding of all
equipment.
Many parts of this drive, including the printed circuit boards, operate at the line voltage. DO NOT TOUCH. Use only electrically insulated tools.
DO NOT touch unshielded components or terminal strip screw connections with voltage present.
DO NOT short across terminals PA/+ and PC/- or across the DC bus capacitors.
Before servicing the drive:
- Disconnect all power, including external control power that may be present.
- Place a "DO NOT TURN ON" label on all power disconnects.
- Lock all power disconnects in the open position.
- WAIT 15 MINUTES to allow the DC bus capacitors to discharge.
- Measure the voltage of the DC bus between the PA/+ and PC/- terminals to ensure that the voltage is less than 42 Vdc.
- If the DC bus capacitors do not discharge completely, contact your local Schneider Electric representative. Do not repair or operate
the drive
Install and close all covers before applying power or starting and stopping the drive.
Failure to follow these instructions will result in death or serious injury.
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider
Electric for any consequences arising out of the use of this product.
Information below is designed to use single drive connected to single motor with a motor cable length less than 50 meters (164 ft).
In any other case, consult the ATV312 installation manual (BBV46391) and programming manual (BBV46385) on www.schneider-electric.com.
Check the delivery of the drive
Remove ATV312 from the packaging and check that it has not been damaged.
WARNING
DAMAGED DRIVE EQUIPMENT
Do not operate or install any drive or drive accessory that appears damaged.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Check that the drive reference printed on the label matches the delivery note and corresponding purchase order.
Write the drive Model Reference: _____________ ___________and Serial Number: ____________________________
Check the line voltage compatibility
Check that the line voltage is compatible with the supply range of the drive.
Line voltage _______ Volts / Drive voltage range _______ Volts
Drive range: ATV312
M2 = 200/240 V single phase / ATV312
M3=200/240 V three-phase
ATV312
N4 = 380/500 V three-phase / ATV312
S6 = 525/600 V three-phase
8B0917121134
Mount the drive vertically

(a)
For a surrounding air temperature up to 50 C (122 F)
(a)
(a)
(a)
(b)
(a) 50 mm (2 in.)
(b)
10 mm (0.4 in.)
See installation manual (BBV46391) on www.schneider-electric.com for other thermal conditions.
www.schneider-electric.com
1/4
S1A10942 - 02/2012
Connect power wiring
Connect control wiring and

select control configuration:
5.1 or 5.2
5
Wire the drive to the ground.

Check circuit breaker rating or fuse rating (see SCCR annex)
Check that the motor voltage is compatible with the drive voltage.
Motor voltage ______Volts.
Wire the drive to the motor.
Wire the drive to the line supply.
[REMOTE configuration]
5.1 (Control by external reference)

Source
CLI
SINK
Ensure SW1 = SOURCE
Wire the speed reference:

RUN
CAN
ERR
AI 1
+10 v
CONF
M2
COM
REF
MON
200/240 V
ATV312
or
200/240 V
ATV312
2.2 K
See
SCCR annex
Wire the command:

Control command 2-wire:
M3
Control command 3-wire:

ATV 312
ATV 312
OR
24 V
LI1
LI2
LI1
24 V
LI2
LIx
380/500 V
ATV312
N4
LI1: forward
LI2: reverse
525/600 V
ATV312
LI1: stop
LI2: forward
LIx: reverse
6 + 7 + 8 +
Next steps, do:
9.1
S6
[LOCAL configuration]
5.2 (control by internal reference).

REF
MON
CONF
RUN
CAN
ERR
Do:
6 + 7 + 8 + 9.2
Apply power to the drive
Ensure that Logic Inputs are not active (see Li1, Li2, Lix ).
ENT
Apply power to the drive.
At first power up, the drive displays nSt (3-wire control) or rdY (2 -wire control), after pushed
drive displays bFr.
On next start-ups, the drive displays nSt or rdY .
Set motor parameters
Refer to the motor nameplate for the following parameter settings.

Menu
Code
bFr
UnS
drC[MOTOR CONTROL]
FrS
nCr
nSP
COS
Description
Factory setting
[Standard mot. freq]:

Standard motor frequency (Hz)
[Rated motor volt.]:
Nominal motor voltage on motor nameplate (V)
[Rated motor freq.]:
Nominal motor frequency on motor nameplate (Hz)
[Rated mot. current.]:
Nominal motor current on motor nameplate (A)
[Rated motor speed]:
Nominal motor speed on motor nameplate (rpm)
[Motor 1 Cosinus Phi.]:
Nominal motor cos on motor nameplate
50.0
2/4
Customer
setting
drive rating
50.0
drive rating
drive rating
drive rating
S1A10942 - 02/2012
Set motor parameters (continued)
Set tUn parameter to YES.

Menu
drC[MOTOR CONTROL]
Code
tUn
Description
Factory setting
[Auto Tunning]:
Auto-Tunning for UnS, FrS, nCr, nSP, nPr and COS
nO
DANGER
Customer
setting
DANGER
HAZARD OF ELECTRIC SHOCK OR ARC FLASH
UNINTENDED EQUIPMENT OPERATION
During auto-tuning, the motor operates at rated

current.
Do not service the motor during auto-tuning.
The Nominal Motor Parameters UnS, FrS, nCr, nSP, nPr and
COS must be correctly configured before starting auto-tuning.
If one or more of these parameters is modified after auto-tuning has
been performed, tUn will return to nO and the procedure must be
repeated.
Failure to follow these instructions will result in death

or serious injury.
Set basic parameters

Menu
Code
Description
Factory setting
ACC
[Acceleration]:
Acceleration time (s)
[Deceleration]:
Deceleration time (s)
[Low speed]:
Motor frequency at minimum reference (Hz)
[High speed]:
Motor frequency at maximum reference (Hz)
[Mot. therm. current]:
Nominal current on motor nameplate (A)
[Reverse assign.]:
Reverse assignment
[2 preset speeds]:
Preset speeds
[4 preset speeds]:
Preset speeds
[Summing ref. 2]
Analog input
3.0
dEC
SEt[SETTINGS]
LSP
HSP
ItH
I-O[INPUTS / OUTPUTS CFG]

Fun-> PSS[PRESET SPEEDS]
Fun-> SAI[SUMMING INPUTS]
Failure to follow these instructions will result in death or serious injury.
rrS
PS2
PS4
SA2
Customer
setting
3.0
0.0
50.0
drive rating
LI2
LI3
LI4
AI2
Set control choice
Menu
CtL[COMMAND]
I-O[INPUTS / OUTPUTS CFG]
Code
Fr1
tCC
9.1 [REMOTE configuration]

(Factory setting)
Description
[Ref.1 channel]:
Reference control
[2/3 wire control]:
Command control
5.1 [REMOTE configuration]

Al1 (factory setting),
Al2, Al3
2C: 2-wire (factory setting)
3C: 3-wire
5.2 [LOCAL configuration]
Customer Setting
AlU1
LOC
9.2 [LOCAL configuration]

MODE
Factory settings of parameters:

Fr1 = AI1
tCC = 2C
3s
LOC
Factory settings of parameters:

Fr1 = AIU1
tCC = LOC
rrS = LI2
PS2 = LI3
PS4 = LI4
rdY
35.
1
[Output frequency] (Hz)
10
Start the motor
3/4
S1A10942 - 02/2012
Menus structure
= ENT
MODE
ESC
3s
rEN
These 3 parameters are

only visible at first power up
of the drive.
Settings can be changed
subsequently in menu:
drC- for bFr
CtL- for Fr1
I-O- for tCC.
LOC
rdY
2s
ESC
3s
bFr
35.
Fr1
rdY
MODE
ENT
[Output frequency] (Hz)
tCC
[SPEED REFERENCE]
rEF-
[SETTINGS]
SEt-
[MOTOR CONTROL]
drC-
[INPUTS / OUTPUTS CFG]
I-O-
[COMMAND]
CtL-
[APPLICATION FUNCT.]
FUn-
[FAULT MANAGEMENT]
FLt-
[COMMUNICATION]
COM-
[MONITORING]
SUP-
MODE
Parameter selection
= ENT
ESC
SEt-
ESC
15.
ACC
ENT
ESC
Refer to the programming manual (BBV46385) for comprehensive menu descriptions.
ENT
dEC
26.
ENT
SFr
A dash appears after menu codes to differentiate them from parameter codes.
Example:
[SETTINGS] (SEt-), ACC parameter.
26.
1 flash
(save)
4/4
S1A10942 - 02/2012

ATV 312 Quick Start

Uploaded by

Copyright:

Available Formats

ATV 312 Quick Start

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ATV 312 Quick Start

Uploaded by

Copyright:

Available Formats

Quick Start Guide - ATV312

Check the delivery of the drive

Check the line voltage compatibility

Mount the drive vertically

For a surrounding air temperature up to 50 C (122 F)

See installation manual (BBV46391) on www.schneider-electric.com for other thermal conditions.

Connect power wiring

Connect control wiring and

Wire the drive to the ground.

5.1 (Control by external reference)

Ensure SW1 = SOURCE

Wire the speed reference:

Wire the command:

Control command 3-wire:

Next steps, do:

5.2 (control by internal reference).

Apply power to the drive

Set motor parameters

Refer to the motor nameplate for the following parameter settings.

[Standard mot. freq]:

Set motor parameters (continued)

Set tUn parameter to YES.

HAZARD OF ELECTRIC SHOCK OR ARC FLASH

UNINTENDED EQUIPMENT OPERATION

During auto-tuning, the motor operates at rated

Failure to follow these instructions will result in death

Set basic parameters

I-O[INPUTS / OUTPUTS CFG]

Failure to follow these instructions will result in death or serious injury.

Set control choice

9.1 [REMOTE configuration]

5.1 [REMOTE configuration]

5.2 [LOCAL configuration]

9.2 [LOCAL configuration]

Factory settings of parameters:

Factory settings of parameters:

Start the motor

These 3 parameters are

[Output frequency] (Hz)

[INPUTS / OUTPUTS CFG]

Refer to the programming manual (BBV46385) for comprehensive menu descriptions.

You might also like