A10VO 52 Series Re-A92703

Download as pdf or txt
Download as pdf or txt
You are on page 1of 68
At a glance
Powered by AI
The document discusses an axial piston variable pump (A10VO) from Bosch Rexroth, including its features, specifications, control options, and safety instructions.

The A10VO axial piston pump is used in hydrostatic drives in open circuits, with its flow proportional to drive speed and displacement. It can provide variable flow by adjusting the swashplate angle.

Control options for the A10VO pump include hydraulic and electric pressure control, power control, and proportional control with options for pressure, flow, and power control.

Axial piston variable pump

A10VO series 52 and 53


RE-A 92703
Edition: 03.2015

Americas

Replaces: 12.2011
Sizes 10 to 100
Nominal pressure 3600psi (250bar)
Maximum pressure 4550psi (315bar)
Open circuit

A10VO 63DRS/53...

Features
Variable axial piston pump of swashplate design for
hydrostatic drives in open circuit.
The flow is proportional to the drive speed and the
displacement.
The flow can be infinitely varied by adjusting the swashplate angle.
Stable storage for long service life
High permissible drive speed
Favorable power-to-weight ratio compact dimensions
Low noise
Excellent suction characteristics
Electro-hydraulic pressure control
Power control
Electro-proportional swivel angle control
Short response times

Contents
Ordering code

Hydraulic fluids

Operating pressure range

7
8

Technical data
DR Pressure control

12

DRG Pressure control remotely operated

13

DRF (DFR) / DRS (DFR1) / DRSC Pressure


and flow control

14

LA... Pressure, flow and power control

16

LA... Variations

17

ED Electro-hydraulic pressure control

18

ER Electro-hydraulic pressure control

19

EP Electro-proportional control

20

EK Electro-proportional control with


controller cut-off

21

EP(K).DF / EP(K).DS / EP(K) with


pressure and flow control

22

EP.ED / EK.ED with

electro-hydraulic pressure control

23

Dimensions, size 10 to 100

24

Dimensions through drive

57

Overview of attachment options

61

Combination pumps A10VO + A10VO

62

Connector for solenoids

63

Installation instructions

64

Project planning notes

68

Safety instructions

68

RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


Ordering code

Ordering code
01

02

A10V(S)

03

04

05

06

07

5x

Axial piston unit


01

08

09

10

11

12

Swashplate design, variable, nominal pressure 3600psi (250bar), maximum pressure


4550psi (315bar)

10

18

28

45 601) 63

72

85 100

A10VS

A10V

Operation mode
02

Pump, open circuit

Size (NG)
03

Geometric displacement, see table of values on page 6

10

18

28

45

60

63

72

85 100

Control devices
04

Pressure control
with flow control

hydraulic

1)

2)
3)
4)

DFR

2)

DRF

3)

DFR1

with flushing function

2)

DRS

without flushing function

DRSC

electrically overridden (negative control)

EF.D.4)

hydraulic

remotely operated

electric

negative control

electric
Power control with
pressure cut-off

DR

hydraulic

X-T open
X-T plugged

pressure cut-off

3)

hydraulic

positive control
start of control

from

DRG

U = 12 V

ED71

U = 24 V

ED72

U = 12 V

ER715)

U = 24 V

ER725)

145 to 510psi
(10 to 35bar)

LA5D

520 to 1015
(36 to 70bar)

LA6D

1030 to 1520psi
(71 to 105bar)

LA7D

1535 to 2030psi
(106 to 140bar)

LA8D

2045 to 3335psi
(141 to 230bar)

LA9D

remotely operated

hydraulic

start of control

see LA.D

LA.DG

flow control, X-T


plugged

hydraulic

start of control

see LA.D

LA.DS

electrically
overridable
(negative
control)

start of control

see LA.D

LA.S

Series 52 units are delivered as standard with 3.66 in3 (60 cm3).
Higher values on request
Series 53 only with D flange
Series 52 only with C flange
See data sheet 92709

Bosch Rexroth AG, RE-A 92703/03.2015

5)

The following must be taken into account during project planning:


Excessive current levels (I > 1,200mA with 12 V or I > 600mA with
24 V) to the ER solenoid can result in undesired increase of pressure which can lead to pump or system damage:
- Use Imax current limiter solenoids.
- An intermediate-plate pressure controller can be used to protect
the pump in the event of overflow.
An accessory kit with intermediate plate pressure controller can be
ordered from Bosch Rexroth under part number R902490825.

Axial piston variable pump | A10VO series 52 and 53 3


Ordering code




01

02

A10V(S)

04

03

Proportional control

04

05

/
electric

06

07

5x

08

09

10

11

12

V
10

18

28

45 601) 63

72

85 100

EP1D
EP2D

positive control

with pressure control

U = 12 V
U = 24 V

with pressure and flow control


(load sensing)

X-T open

U = 12 V

EP1DF

U = 24 V

EP2DF

with pressure and flow control


(load sensing)

X-T plugged

U = 12 V

EP1DS

with electro-hydraulic pressure


control
Proportional control

electric

U = 24 V

EP2DS

U = 12 V

EP1ED

U = 24 V

EP2ED

positive control

Pressure and flow control with


controller cut-off (load sensing)

X-T open

U = 12 V

EK1DF

U = 24 V

EK2DF

Pressure and flow control with


controller cut-off (load sensing)

X-T plugged

U = 12 V

EK1DS

U = 24 V

EK2DS

U = 12 V

EK1ED

U = 24 V

EK2ED

Series 5, index 2

526)10)

Series 5, index 3

537)8)9)

Electro-hydraulic pressure control


with controller cut-off
Series
05

Direction of rotation
06

View on drive shaft

clockwise

counter clockwise

Sealing material
07

FKM (fluor-caoutchouc)

Drive shaft
08

Splined shaft

standard shaft

ANSI B92.1a

similar to shaft S however for higher input torque

reduced diameter, limited suitability for through drive

similar to shaft U, however for higher torque

Parallel keyed shaft ISO 3019-1 limited suitability for through drive

Tapered with Woodruff key (only series 52)

2-hole

4-hole

Mounting flange
09

6)

7)

8)

ISO 3019-1 (SAE)

Control DR, DFR, DFR1, DRG, ED and ER: delivery with nominal
sizes 10, 28, 45, 60 and 8510) only in series 52
Control DR, DRF, DRS, DRG, ED and ER: delivery with nominal
sizes 18, 63, 72, 859) and 100 only in series 53
Control EF., LA.., EP.. and EK..: delivery with nominal sizes 18 to
100 only in series 53

11)

Control DRF and DRS: delivery with nominal size 85 only with
Dflange in series 53
10) Control DFR, DFR1: delivery with nominal size 85 only with
Cflange in series 52
11) Only available in series 53. For controller designation and series
assignment, please refer to positions 04, 05, including footnotes.
9)

RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


Ordering code

01

02

A10V(S)

03

04

05

06

5x

07

Working port
10

SAE flange port


UNC fastening thread
ISO threaded port

08

09

10

11

12

V
10

18

28

45 601) 63

72

85 100

rear

not for through drive

61

at side, opposite

for through drive

62

rear

not for through drive

64

10 18

28

45 601) 63

72

85 100

N00

9T 16/32DP

K01

Through drive (for attachment options, see page 61)


11

Flange ISO 3019-1

Hub for splined shaft12)

Diameter

Diameter

without through drive


82-2 (A)

5/8 in
3/4 in

11T 16/32DP

K52

101-2 (B)

7/8 in

13T 16/32DP

K68

1 in

15T 16/32DP

K04

127-4 (C)
127-2 (C)

1 1/4 in

14T 12/24DP

K15

1 1/2 in

17T 12/24DP

K16

1 1/4 in

14T12/24DP

K07

1 1/2 in

17T 12/24DP

K24

Connector for solenoids


12

DEUTSCH molded connector, 2-pin without suppressor diode (for electric controls)

= Available

= On request

= Not available

Note
Note the project planning notes on page68!
Preservation:
Up to 12 months as standard
Up to 24 months long-term (state in plain text when
ordering)

12) According

to ANSI B92.1a

Bosch Rexroth AG, RE-A 92703/03.2015

Axial piston variable pump | A10VO series 52 and 53 5


Hydraulic fluids




Hydraulic fluids
The A10VO variable pump is designed for operation with

Notes on selection of hydraulic fluid

HLP mineral oil according to DIN 51524.

The hydraulic fluid should be selected such that the operat-

Application instructions and requirements for hydraulic

ing viscosity in the operating temperature range is within

fluids should be taken from the following data sheets

the optimum range (opt: see selection diagram).

before the start of project planning:


Note

90220: Hydraulic fluids based on mineral oils and

At no point of the component may the temperature be

related hydrocarbons

higher than 239F (115 C). The temperature difference

90221: Environmentally acceptable hydraulic fluids

specified in the table is to be taken into account when


determining the viscosity in the bearing.
If the above conditions cannot be maintained due to
extreme operating parameters, please contact the responsible member of staff at Bosch Rexroth.
Viscosity and temperature of hydraulic fluids
Cold start

Viscosity

Temperature

Comment

max7500SUS
(1600 mm2/s)

St-40 F (-40 C)

t1 min, without load (p435psi (30bar)), n1000rpm

T45F (25K)

between axial piston unit and hydraulic fluid

=-40F to -13F
(-40 C to -25 C)

Note the detailed information on operation with low temperatures, see data sheet 90300-03-B.

Permissible temperature difference


Warm-up phase

<7500 to 1850SUS
(1600 to 400 mm2/s)

Continuous operation

=1850 to 60SUS
(400 to 10 mm2/s)

This corresponds, for example on the VG46, to a temperature


range of 41F (+5 C) to 185F (+85 C) (see selection diagram page5)
=-13F to +230F
(-25C to +110C)

Short-term operation

measured at port L
Note the permissible temperature range of the shaft seal
(T=approx.9F (5K) between the bearing/shaft seal and
port L)

opt=170 to 80SUS
(36 to 16 mm2/s)

Range of optimum operating viscosity and efficiency

min49SUS (7 mm2/s)

t<1 min, p<0.3pnom

Selection diagram
[mm2/s]
1600
1000
600
400

Warm-up phase

[SUS]
1600
4600
3000
2000

Continuous operation

500

60

300

40
36

200
170

20
16

100
74

10

60

Minimum permissible viscosity for short-term operation

Minimum permissible temperature for cold start




20

VG

Range of optimum operating viscosity vopt


Optimum efficiency

100

0
10
VG 68
VG 46
VG 32
VG 2
2

200 1000

-40
-40

-13
-25

-14
-10

32 50
0 10

Viscosity [mm2/s]

Maximum permissible viscosity for cold start

86
122
158
30
50
70
Temperature [C]

194
90

239 [F]
115 [C]

RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


Ordering code

Filtration of the fluid


The finer the filtration, the better the hydraulic fluid cleanliness level, and the longer the service life of the axial piston
unit.
A cleanliness level of at least 20/18/15 is to be maintained
according to ISO 4406.
At very high hydraulic fluid temperatures (194F (90 C) to
maximum 239F (115 C)), a cleanliness level of at least
19/17/14 according to ISO 4406 is necessary.
Please contact us if the above classes cannot be observed.

Bosch Rexroth AG, RE-A 92703/03.2015

Axial piston variable pump | A10VO series 52 and 53 7


Operating pressure range




Operating pressure range


Pressure at working port B

Definition

Nominal pressure pnom

3600psi (250bar) absolute

The nominal pressure corresponds to the maximum design pressure.

Maximum pressure pmax

4550psi (315bar) absolute

The maximum pressure corresponds the maximum operating pressure


within the single operating period. The sum of the single operating
periods must not exceed the total operating period.

Single operating period


Total operating period

2.5ms
300 h

Minimum pressure pB abs


(high pressure side)

145psi (10bar) absolute

Minimum pressure on the high-pressure side (B) which is required in order to prevent damage to the axial piston unit.

Rate of pressure change RAmax

235000psi/s (16000bar/s)

Maximum permissible rate of pressure build-up and pressure reduction


during a pressure change over the entire pressure range.

Minimum pressure pSmin Standard

10psi (0.8bar) absolute

Minimum pressure at suction port S (inlet) that is required in order to


avoid damage to the axial piston unit. The minimum pressure depends on
the speed and displacement of the axial piston unit.

Maximum pressure pSmax

75psi (5bar) absolute

Pressure at suction port S (Inlet)

Case drain pressure at port L1, L2


Maximum pressure pLmax

30psi (2bar) absolute

Rate of pressure change RAmax

Maximum 7.5psi (0.5bar) higher than inlet pressure at port S, but not
higher than pLmax. A case drain line to the reservoir is required.
Pressure definition

pnom

Single operating period

Pressure p

t1

t2

tn

Maximum pressure pmax


Pressure p

Nominal pressure pnom


p

Time t

Minimum pressure (high pressure side)

Maximum permissible speed (limit speed)

Permissible speed by increasing inlet pressure pabs at


suction opening S or at Vg Vgmax

Time t

Total operating period = t1 + t2 + ... + tn


Note
Operating pressure range valid when using hydraulic

1.2

fluids based on mineral oils. Please contact us for values

1.4

1.1

1.2
1.0

1.0

0.9
0.9

0.7

0.9
0.8
Displacement Vg/Vgmax

Inlet pressure pabsbar

Speed n/nmax

1.6

for other hydraulic fluids.

0.8
1.0

RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


Technical data

Technical data
Size

NG

Displacement, geometric, per


revolution

Vg max in
(cm3)

Maximum at Vg max
rotational at V <V
g
g max
speed3)

nnom
nmax

Flow

10

18

28

45

601)

632)

72

85

100

0.64
(10.5)

1.10
(18)

1.75
(28)

2.75
(45)

3.66
(60)

3.84
(63)

4.39
(72)

5.18
(85)

6.10
(100)

rpm

3600

3300

3000

26004)

2700

2600

2600

2500

2300

rpm

4320

3960

3600

3120

3140

3140

3140

3000

2500

perm

at nnom and Vg max

qv

gpm
(l/min)

9.7
(37)

15.6
(59)

22
(84)

31
(117)

41
(156)

43
(163)

49.4
(187)

55
(212)

60
(230)

at nE = 1500 rpm

qvE

gpm
(l/min)

4
(15)

7.1
(27)

1.1
(42)

18
(68)

24
(90)

25.1
(95)

28.5
(108)

34
(128)

39
(150)

at nnom, Vg max and P


p = 3600psi
(250bar)

HP
(kW)

22
(16)

34
(25)

47
(35)

65
(49)

88
(65)

90
(68)

103
(77)

119
(89)

130
(96)

at nE = 1500 rpm

PE

HP
(kW)

9.4
(7)

15
(11)

24
(18)

38
(28)

50
(37)

52
(39)

60
(45)

71
(53)

84
(62)

at Vg max and
p = 3600psi
(250bar)

lb-ft
(Nm)

31
(42)

52
(71)

82
(111)

132
(179)

175
(238)

184
(250)

211
(286)

247
(338)

293
(398)

at Vg max and
p = 1440psi
(100bar)

lb-ft
(Nm)

13
(17)

21
(29)

33
(45)

53
(72)

70
(95)

74
(100)

84
(114)

102
(135)

117
(159)

lb-ft/rad 6760
(Nm/rad) (9200)

8082
(11000)

16400
(22300)

27560
48100
(37500) (65500)

48100
(65500)

48100
(65500)

105100
105100
(143000) (143000)

lb-ft/rad
(Nm/rad) ()

10870
(14800)

19400
(26300)

30240
51200
(41000) (69400)

51200
(69400)

51200
(69400)

()

()

lb-ft/rad 5020
(Nm/rad) (6800)

5870
(8000)

()

22130
36290
(30000) (49200)

36290
(49200)

36290
(49200)

75900
(102900)

75900
(102900)

lb-ft/rad
(Nm/rad) ()

()

()

25370
39830
(34400) (54000)

39830
(54000)

39830
(54000)

86960
(117900)

86960
(117900)

K/C

lb-ft/rad 7965
(Nm/rad) (10800)

()

19770
(26800)

32380
54506
(43900) (73900)

()

()

()

()

Moment of inertia for rotary


group

JTW

lbs-ft2
(kgm2)

0.0142
0.2207
0.0403
0.0783
(0.0006) (0.0009) (0.0017) (0.003)

0.1329
(0.0056)

0.1329
0.1329
0.2848
(0.0056) (0.0056) (0.012)

0.2848
(0.012)

Maximum angular acceleration5)

rad/s

8000

6800

5500

4000

3300

3300

3300

2700

2700

Case volume

gal
(L)

0.05
(0.2)

0.06
(0.25)

0.08
(0.3)

0.13
(0.5)

0.21
(0.8)

0.21
(0.8)

0.21
(0.8)

0.26
(1)

0.26
(1)

Weight without through drive


(approx.)

lbs
(kg)

17
(8)

25
(11.5)

33
(15)

40
(18)

48.5
(22)

48.5
(22)

48.5
(22)

79
(36)

79
(36)

lbs
(kg)

()

28.6
(13)

40
(18)

53
(24)

62
(28)

62
(28)

62
(28)

99
(45)

99
(45)

Power

Torque

Rotary
stiffness
of drive
shaft

Weight with through drive


(approx.)

1)
2)
3)

4)

Only series 52
Only series 53
The values are applicable:
At absolute pressure pabs = 15psi (1bar) at suction port S
For the optimal viscosity range of
opt=170 to 80SUS (36 to 16 mm2/s)
For hydraulic fluid based on mineral oils
Please contact us regarding higher speeds

Bosch Rexroth AG, RE-A 92703/03.2015

5)

The scope of application lies between the minimum necessary and


the maximum permissible drive speeds. It applies for external stimuli (e. g. engine 2 to 8 times rotary frequency, cardan shaft twice
the rotary frequency). The limiting value is only valid for a single
pump. The loading capacity of the connecting parts must be taken
into account.

Axial piston variable pump | A10VO series 52 and 53 9


Technical data




Determining the operating characteristics


Flow

qv =

Torque

T =

Power

P =

Vg n v

[gpm
(l/min)]

231 (1000)
Vg p

[lb-ft
(Nm)]

24 (20) mh
2Tn
33000 (60000)

qv p
[HP
1714 (600) t (kW)]

Key
Vg

Displacement per revolution [in3 (cm3)]

Differential pressure [psi (bar)]

Rotational speed [rpm]

Volumetric efficiency

mh

Mechanical-hydraulic efficiency

Total efficiency (t = v mh)

Note
Theoretical values, without efficiency and tolerances;
values rounded.
Operation above the maximum values or below the
minimum values may result in a loss of function, a
reduced service life or in the destruction of the axial
piston unit. We recommend testing the loads by means
of experiment or calculation / simulation and comparison with the permissible values.

RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


Technical data

10

Permissible radial and axial forces on the drive shaft


Size

NG

Radial force maximum at a/2

Fq

10

18

28

45

60/63

72

85

100

Fq max

lbf
(N)

56
(250)

78
(350)

270
(1200)

337
(1500)

382
(1700)

337
(1500)

450
(2000)

450
(2000)

+ Fax max

lbf
(N)

90
(400)

157
(700)

225
(1000)

337
(1500)

450
(2000)

337
(1500)

675
(3000)

675
(3000)

a/2 a/2
a

Axial force maximum

Fax

Note
The values given are maximum values and do not apply
to continuous operation. For drives with radial loading
(pinion, V-belt drives), please contact us!
Permissible input and through-drive torques
Size
Torque at Vg max and p = 3600psi (250bar)

1)

10

18

28

45

60/63

72

85

100

T max

lbft
(Nm)

31
(42)

52
(71)

82
(111)

132
(179)

184
(250)

211
(286)

247
(338)

293
(398)

TE max

lb-ft
(Nm)

93
(126)

91
(124)

146
(198)

235
(319)

464
(630)

464
(630)

853
(1157)

814
(1104)

DIA

in

3/4

3/4

7/8

11/4

11/4

1 1/2

1 1/2

TE max

lb-ft
(Nm)

()

118
(160)

184
(250)

295
(400)

479
(650)

479
(650)

Input torque at drive shaft, maximum2)


S

DIA

in

3/4

7/8

11/4

11/4

TE max

lb-ft
(Nm)

44
(60)

43
(59)

77
(105)

139
(188)

226
(306)

226
(306)

463
(628)

438
(595)

DIA

in

5/8

5/8

3/4

7/8

11/4

11/4

TE max

lb-ft
(Nm)

()

()

103
(140)

162
(220)

292
(396)

282
(383)

479
(650)

469
(636)

DIA

in

3/4

7/8

11/4

11/4

TE max

lb-ft
(Nm)

78
(106)

76
(104)

107
(145)

156
(212)

325
(441)4)

()

()

553
(750)

DIA

in

3/4

3/4

7/8

1.000

1 1/4

1 1/2

TE max

lb-ft
(Nm)

()

()

107
(145)

156
(212)

325
(441)4)

()

()

()

TD max

lb-ft
(Nm)

()

80
(108)

118
(160)

235
(319)

357
(484)

357
(484)

515
(698)

573
(778)

TD max

lb-ft
(Nm)

()

89
(120)

130
(176)

270
(365)

357
(484)

357
(484)

()

()

TD max

lb-ft
(Nm)

()

43
(59)

77
(105)

139
(188)

226
(306)

226
(306)

463
(628)

438
(595)

TD max

lb-ft
(Nm)

()

()

103
(140)

162
(220)

292
(396)

282
(383)

479
(650)

469
(636)

TD max

lb-ft
(Nm)

()

()

107
(145)

156
(212)

325
(441)4)

()

()

553
(750)

C
Maximum through-drive torque

1)
2)
3)
4)

Without considering efficiency


For drive shafts with no radial force
only series 52
only size 60

Bosch Rexroth AG, RE-A 92703/03.2015

Axial piston variable pump | A10VO series 52 and 53 11


Technical data




Distribution of torques
T1

T2

TE

1st pump

2nd pump

T3

TD

Torque at 1st pump

T1

Torque at 2nd pump

T2

Torque at 3rd pump

T3

Input torque

TE

T1 + T2 + T3

TE

<

TE max

TD

T2 + T3

TD

<

TD max

Through-drive torque

RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


DR Pressure control

12

DR Pressure control
The pressure control limits the maximum pressure at the

Schematic: DR

pump outlet within the control range of the variable pump.


The variable pump only supplies as much hydraulic fluid as
is required by the consumers. If the operating pressure
exceeds the pressure setting at the pressure valve, the
pump will regulate to a smaller displacement to reduce the
control differential.

L1

Basic position in depressurized state:Vg max.


Setting range1) for pressure control 510 to 3600psi
(35 to 250bar). Standard is 3600psi (250bar).
Characteristic curve DR

Operating pressure pB

Hysteresis/pressure rise p

max

[bar] [psi]
250 3600

35

510

qv min

Flow qV]

qv max

Characteristic curve valid for n1 = 1500 rpm and tfluid = 120F


(50 C).

1)

In order to prevent damage to the pump and the system, the permissible setting range must not be exceeded. The range of possible settings at the valve is higher.

Bosch Rexroth AG, RE-A 92703/03.2015

L2

Controller data
NG

10

18

28

45

60
63

72

85

Pressure
increase

p [psi] 90
(6)
[bar]

90
(6)

90
(6)

90
(6)

115 115 175


(8) (8) (12)

Hysteresis
and repeatability

p [psi
(bar)]

maximum 45 (3)

Control
fluid consumption

gpm
(l/min)

maximum approx. 0.8 (3)

100
200
(14)

Axial piston variable pump | A10VO series 52 and 53 13


DRG Pressure control remotely operated




DRG Pressure control remotely operated


For the remote-controlled pressure control, the target

Schematic DRG

pressure can be set using a separately arranged pressure


relief valve. Pressure control DR see page 12.
A pressure relief valve can be externally piped to port X for
remote setting of pressure below the setting of the DR

control valve spool. This relief valve is not included in the


delivery contents of the pump.
The differential pressure at the DRG control valve is set as
standard to 290psi (20bar). This results in a pilot oil flow
to the relief valve of approx. 0.4gpm (1.5 l/min) at port X.
If another setting is required (range from 145 to 320psi
(10-22bar)) please state in clear text.
As a separate pressure relief valve we can recommend:

DBDH 6 (hydraulic) to RE 25402 or

L1

L2

DBETR-SO 381 with orifice dia 0.03 inch ( 0.8 mm) in P


(electric) to RE29166.
The max. length of piping should not exceed 6.6ft (2m).
Basic position in depressurized state:Vg max.
Setting range1) for pressure control 290 to 3600psi (20
to 250bar). Standard is 3600psi (250bar).

max

250 3600

Operating pressure pB

[bar] [psi]

Hysteresis/pressure rise p

Characteristic curve DRG

20

290

qv min

Flow qV]

Controller data
NG

10

18

28

45

60
63

72

85

Pressure
increase

p [psi] 90
(6)
[bar]

90
(6)

90
(6)

90
(6)

115 115 175


(8) (8) (12)

Hysteresis
and repeatability

p [psi
(bar)]

maximum 45 (3)

Control
fluid consumption

gpm
(l/min)

maximum approx. 1.2 (4.5)

100
200
(14)

qv max

Characteristic curve valid at n1 = 1500 rpm and tfluid = 120F


(50 C).

1)

In order to prevent damage to the pump and the system, the permissible setting range must not be exceeded. The range of possible settings at the valve is higher.
RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


DRF (DFR) / DRS (DFR1) / DRSC Pressure and flow control

14

DRF (DFR) / DRS (DFR1) / DRSC Pressure and flow control


In addition to the pressure control function (see

Possible connections at port B

page12), a variable orifice (e.g. directional valve) is used

(not included in the delivery contents)

to adjust the differential pressure upstream and downstream of the orifice. This is used to control the pump flow.
The pump flow is equal to the actual required flow by the
consumer, regardless of changing pressure levels. The

Data sheets

M4-12

64276

M4-15

64283

LUDV mobile control blocks

pressure control overrides the flow control function.


Basic position in depressurized state:Vg max.
Setting range1) for pressure control 510 to 3600psi
(35 to 250bar). Standard is 3600psi (250bar).

M6-15

64284

M7-22

64295

DRF (DFR) schematic

Characteristic curve DRF (DFR) / DRS (DFR1) / DRSC

Plugged at DRS (DFR1) / DRSC valve


max

X
1

Operating pressure pB

Hysteresis/pressure rise p

[bar] [psi]
250 3600

35

LS mobile control blocks

L1

510

qv min

Flow qV]

qv max

Flow qV]

qV max

qV min

n0

Rotational speed n

n max

Hysteresis/Pressure increase qV max

Characteristic curve at variable speed

Characteristic curves valid for n1 = 1500 rpm and tfluid = 120F


(50 C).

L2

1 The metering orifice (control block) and the line is not


included in the delivery contents.
Note
The DRS (DFR1) and DRSC valve versions have no bleeddown between X and the reservoir.
Unloading the LS-pilot line must be accomplished in the
valve system.
Because of the flushing function, sufficient unloading of
the flow control in DRS (DFR1) control valve X-line must
also be provided in the valve system.
If the unloading of the X line cannot be accomplished in
the valve system, the DRSC control valve must be used.
For further information see page15

1)

In order to prevent damage to the pump and the system, the permissible setting range must not be exceeded. The range of possible settings at the valve is higher.

Bosch Rexroth AG, RE-A 92703/03.2015

Axial piston variable pump | A10VO series 52 and 53 15


DRF (DFR) / DRS (DFR1) / DRSC Pressure and flow control



Differential pressure p:
Standard setting: 200 to 320psi (14 to 22bar).
If another setting is required, please state in clear text.

Relieving the load on port X to the reservoir results in a


zero stroke (standby) pressure which lies about 15 to
30psi (1 to 2bar) higher than the differential pressure p).
No account is taken of system influences.
Controller data
DR Pressure control data see page 12.
Maximum flow deviation measured at drive speed
n = 1500 rpm.
NG

18

28

45

60
63

72

85

100

0.24 (0.9)

0.26 (1.0)

0.48 (1.8)

0.66 (2.5)

0.66 (2.5)

0.83 (3.1)

0.83 (3.1)

Flow deviation

q vmax [gpm (l/min)]

0.13 (0.5)

Hysteresis and
repeatability

p [psi (bar)]

maximum 45 (3)

Control fluid
consumption

10

gpm (gpm (l/min))

maximum approx. 0.8 to 1.2 (3 to 4.5) (DRF (DFR))


maximum approx. 0.8 (3) (DRS (DFR1) / DRSC)

RE-A 92703/03.2015, Bosch Rexroth AG

16

A10VO series 52 and 53 | Axial piston variable pump


LA... Pressure, flow and power control

LA... Pressure, flow and power control


Pressure control equipped as DR(G), see page12 (13).

control is possible below the power control curve. When

Equipment of the flow control like DRS (DFR1), see page 14.

ordering please state the power characteristics to be set ex

In order to achieve a constant drive torque with varying

works in clear text, e.g. 27HP (20 kW) at 1500 rpm.


Control data

operating pressures, the swivel angle and with it the volume flow from the axial piston pump is varied so that the
product of flow and pressure remains constant. Flow

For technical data of press. control DR seepage12.


For technical data of flow control FR see page 14.
Control fluid cons. max. approx. 1.45gpm (5.5l/min).

Start of control Torque T [lb-ft (Nm)] for nominal size

Order
code

psi (bar)

18

28

45

63

72

85

100

145 to 510
(10 to 35)

2.80 8.92
(3.8 12.1)

4.4 14
(6 19)

7.4 22.1
(10 30)

11 32
(15 43)

12.5 36.3
(17 49.2)

15 42
(20 57)

18 49.5
(24 68)

LA5

520 to 1015
(36 to 70)

8.92 17.2
(12.2 23.3)

14 26.5
(19.1 36)

22.2 43.5
(30.1 59)

32 61
(43.1 83)

36.4 69.9
(49.3 94.9)

42 83
(57.1 112)

49.5 97.1
(68.1 132)

LA6

1030 to 1520
(71 to 105)

17.2 24.9
(23.4 33.7)

26.6 38.4
(36.1 52)

43.6 62
(59.1 84)

61 88
(83.1 119)

70 100.3
(95.0 136.0)

83 118
(112.1 160)

97.1 139.4
(132.1 189)

LA7

1535 to 2030
(106 to 140)

24.9 33.2
(33.8 45)

38.4 51.6
(52.1 70)

62 83
(84.1 112)

88 116
(119.1 157)

100.4 132.3
(136.1 179.4)

118 156
(160.1 212)

139.4 183.6 LA8


(189.1 249)

2045 to 3335
(141 230)

33.2 55.2
(45.1 74.8)

51.7 86.3
(70.1 117)

83 139
(112.1 189)

116 195
(157.1 264)

132.4 222.5
(179.5 301.7)

156 263
(212.1 357)

183.3 309
(249.1 419)

LA9

Conversion of the torque values in power [HP (kW)]


P=

[HP (kW)]

3.5 (6.4)

(at 1500 rpm)

or

Characteristic curve LA.DS

Operating pressure pB

(rotational speeds, see table on page 8)

LA8

150 150

LA7

100 100

[HP (kW)]

LA9

200 200

33000 (60000)

250 250

50

2xTxn

Schematic LA.DS
(for further combination options with LA.. see page17)

[bar] [psi]
300 300

50

P=

LA6
LA5
0

Volume flow qV [%] 100

L1

qV
Torque T [lb-ft (Nm)]

LA9
LA8
LA7
LA6
LA5
0

Volume flow qV [%]

100

L2

1 The metering orifice (control block) and the line is not


Bosch Rexroth AG, RE-A 92703/03.2015

included in the delivery contents.

Axial piston variable pump | A10VO series 52 and 53 17


LA... Variations




LA... Variations
Schematic LA.D with pressure cut-off

Schematic LA.S with separate flow control

1
L

L1

L2

L1

Schematic LA.DG with pressure cut-off, remotely operated


X

L2

1 The metering orifice (control block) and the line is not

included in the delivery contents.

L1

L2

1 The metering orifice (control block) and the line is not


included in the delivery contents.

RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


ED Electro-hydraulic pressure control

18

ED Electro-hydraulic pressure control


The ED valve is set to a certain pressure by a specified
variable solenoid current.
When a change is made at the consumer (load pressure),
the position of the control piston will shift.

Influence of the pressure setting on standby


(maximally energized)
[bar] [psi]
34 500
32

465

30

435

28

405

26

370

24

350

22

320

As the solenoid current signal drops towards zero, the

20

290

pressure will be limited to pmax by an adjustable hydraulic

18

260

pressure cut-off (secure fail safe function in case of a loss

16

230

of power, e.g. for fan drives ). The response time character-

14

200

(flow) in order to maintain the electrically set pressure level.


The pump thus only delivers as much hydraulic fluid as the
consumers can take. The desired pressure level can be set
steplessly by varying the solenoid current.

Standby [bar]

This causes an increase or decrease in the pump swivel angle

istic curve of the ED-control was optimized for the use as a


fan drive system. When ordering, specify the type of appli-

120
120

cation in clear text.


Static current-pressure characteristic curve ED
(negative characteristic curve measured with pump in zero stroke)

Operating pressure pB

[bar] [psi]
250 3600

140
140

160
180
200 220
240 250 [psi]
160
180
200 220
240 250 [bar]
Maximum pressure setting [bar]

Schematic ED71/ED72
X

De-activation
of control

ED

Max. adjustable
control pressure

140 2000

Min. adjustable control pressure


0

Amperage

I/Imax

L1

Hysteresis static < 45psi (3bar).


Flow-pressure characteristic curve
Hysteresis/pressure rise
p max < 60psi (4bar)

Setting range

Maximum operating
pressure pB (de-energized)

[bar] [psi]
250 3600

L2

Technical data, solenoid

ED71

ED72

Voltage

12 V (20%)

24 V (20%)

Start of control at p min

100mA

50mA

End of control at p max

1200mA

600mA

Limiting current

1.54 A

0.77 A

Nominal resistance (at 68F (20 C))

5.5

22.7

Dither frequency

100 to
200 Hz

100 to
200 Hz

Actuated time

100%

100%

Control current

140 2000
qv min

Flow qV]

qv max

Characteristic curves valid for n1 = 1500 rpm and


tfluid = 120F (50 C).
Pilot fluid consumption: 0.8 to 1.2gpm (3 to 4.5 l/min).
Standby standard setting 360psi (23bar). Other values
on request.

Bosch Rexroth AG, RE-A 92703/03.2015

Type of protection: see connector version page 63

Operating temperature range at valve -4F to 239F


(-20C to +115C)

Axial piston variable pump | A10VO series 52 and 53 19


ER Electro-hydraulic pressure control




ER Electro-hydraulic pressure control


The ER valve is set to a certain pressure by a specified

Schematic ER71/ER72
X

variable solenoid current.


When a change is made at the consumer (load pressure),
the position of the control piston will shift.
This causes an increase or decrease in the pump swivel angle
(flow) in order to maintain the electrically set pressure level.
The pump thus only delivers as much hydraulic fluid as the
consumers can take. The desired pressure level can be set
steplessly by varying the solenoid current.
As the solenoid current signal drops towards zero, the
pressure will be limited to pmin (stand by).

Observe the project planning notes on page 2.

L1

Static current-pressure characteristic curve ER


(positive characteristic curve measured with pump in zero stroke)

Operating pressure pB

[bar] [psi]
350 5100
250 3600

Maximum adjustable
control pressure

150 2200
50
14
0

725
200
0

Minimum adjustable control


pressure

Current I/Imax

L2
Technical data, solenoid

ER71

ER72

Voltage

12 V (20%)

24 V (20%)

Start of control at p min

100mA

50mA

End of control at p max

Control current

Hysteresis static current-pressure characteristic curve


<45psi (3bar).

1200mA

600mA

Influence of press. setting on stand-by 30psi (2bar)

Limiting current

1.54 A

0.77 A

Flow-pressure characteristic curve

Nominal resistance (at 68F


(20C))

5.5

22.7

Dither frequency

100 to
200 Hz

100 to
200 Hz

Actuated time

100%

100%

< 4bar
max

Hysteresis/pressure rise p

Setting range

Maximum operating pressure pB


(fully energized)

[bar] [psi]
250 3600

140 2000
qv min

Flow qV

Type of protection: see connector version page 63


Operating temperature range at valve -4F to 239F (-20C to
+115C)

qv max

Characteristic curves valid for n1 = 1500rpm and


tfluid = 120F (50C).
Pilot fluid consumption: 0.8 to 1.2 gpm (3 to 4.5l/min).
Standby standard 200psi (14bar). Other values on
request.


RE-A 92703/03.2015, Bosch Rexroth AG

20

A10VO series 52 and 53 | Axial piston variable pump


EP Electro-proportional control

EP Electro-proportional control
Electro-proportional control makes a stepless and repro-

Circuit diagram EP.D

ducible setting of the pump displacement possible directly


via the swashplate. The control force of the control piston
is applied by a proportional solenoid. The control is proportional to the current (for start of control, see table right).
In a depressurized state, the pump is swiveled to its initial
position (Vg max) by an adjusting spring. If the operating

L1

pressure exceeds 60psi (4bar), the pump will swivel from


Vg max toVg min without control by the solenoid (control
current <start of control). With a minimum swivel angle
Vgmin and de-energized EP solenoids, a minimum pressure
of 145psi (10bar) must be maintained, or alternatively a
minimum amount of 5% of the displacement.
A PWM signal is used to control the solenoid.
EP.D: The pressure control regulates the pump displacement back to Vg min after the set target pressure has been
reached.
We recommend the valve with flushing function for the EP.D
control variant. Please contact us.
A minimum operating pressure of 200psi (14bar) is
needed for control. The necessary control fluid is taken
from the high pressure.

Technical data, solenoid

EP1

EP2

Voltage

12 V (20%)

24 V (20%)

Beginning of control at Vg min

400mA

200mA

End of control at Vg max

Control current
1200mA

600mA

Limiting current

1.54 A

0.77 A

Nominal resistance
(at 68F (20 C))

5.5

22.7

1400

Dither frequency

100 to
200 Hz

100 to
200 Hz

1200

Actuated time

100%

100%

Characteristic curve EP1/2


Hysteresis < 5%

Control current I [mA]

L2

Type of protection: see connector version page 63

1000

Operating temperature range at valve -4F to 239F (-20 C to


+115 C)

EP1
800
600

EP2

400
200

0.5
Displacement [%]

Vg min

1.0
Vg max

Hysteresis static current-pressure characteristic curve


<45psi (3bar).
Influence of pressure setting on stand-by 30psi
(2bar).

Bosch Rexroth AG, RE-A 92703/03.2015

Axial piston variable pump | A10VO series 52 and 53 21


EK Electro-proportional control with controller cut-off




EK Electro-proportional control with controller cut-off


Variant EK... is based completely on the variant EP...

Circuit diagram EK.DF

(seepage20).
In addition to the electro-proportional control function,
acontroller cut-off is integrated in the electric characteristic curve. The pump then swivels to Vg max if the pilot signal
is lost (e.g., cable break) and then works with the DRF

L1

settings if necessary (see page 14). The controller cut-off


is only intended for short-term use and not for permanent
use if the control signal is lost. If the control signal is lost,
the pump swivel times will be increased by the EK valve
A PWM signal is used to control the solenoid.
A minimum operating pressure of 725psi (50bar) is needed
for electro-proportional control with controller cut-off. For
lower pressures, a pilot signal of > 500mA (EK2) or >
1000mA (EK1) is required in order to avoid undesired controller cut-off. The necessary control fluid is taken from the high
pressure.
The Vg max position is maintained by the force of the adjusting spring. To overcome the force of this spring, the solenoid must be subjected to excessive current (Ires).
We recommend the valve with flushing function for the
EK.D control variant. Please contact us.
Observe the instructions regarding the project design on
page 2
Characteristic curve EK1/2
Hysteresis < 5%
1400
Ires

Control current I [mA]

1200

L2
Technical data, solenoid

EK1

EK2

Voltage

12 V (20%)

24 V (20%)

Control current
Beginning of control at Vg min 400mA

200mA

1200mA

End of control at Vg max

600mA

Limiting current

1.54 A

0.77 A

Nominal resistance
(at 68F (20 C))

5.5

22.7

Dither frequency

100 to
200 Hz

100 to
200 Hz

Actuated time

100%

100%

Type of protection: see connector version page 63


Operating temperature range at valve -4F to 239F (-20 C to
+115 C)

1000
EK1
800
600

EK2

Ires

Imin

400

Ioff

EK1

EK2

Imin [mA]

400

200

Imax [mA]

1200

600

Ioff [mA]

<300

<150

Ires [mA]

>1200

>600

Imin

200
Ioff
0

Displacement
[%]
0.5

1.0

Hysteresis static current-pressure characteristic curve


<45psi (3bar).
Influence of pressure setting on stand-by 30psi
(2bar).
For changes in current, ramp times of >200ms must be
observed.


RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


EP(K).DF / EP(K).DS / EP(K) with pressure and flow control

22

EP(K).DF / EP(K).DS / EP(K) with pressure and flow control


A hydraulic pressure flow control is superimposed on the

Circuit diagram EP.DF

electro-proportional control.
The pressure control regulates the pump displacement

back to Vg min after the set target pressure has been


reached.

This function is super-imposed on the EP or EK control,


i.e.the control-current dependent function is executed
below the target pressure.
Setting range from 290 to 3600psi (20 to 250bar). For the
pressure flow control, see page 14.
Pressure control has priority over electro-proportional
L

control and flow control.

L1

With flow control, the pump flow can be influenced in


addition to pressure control. The pump flow is thus equal
to the actual amount of hydraulic fluid required by the
consumer. This is achieved using the differential pressure at
the consumer (e.g. orifice).
The EP.DS or EK.DS version has no connection between X
and the reservoir (load sensing). Please refer to the notes
on page 14.
Circuit diagram EP.D

L2

Circuit diagram EP.DS


L

L1

B
X
1

L
L2

L1

1 The metering orifice (control block) and the line is not


included in the delivery contents.

Bosch Rexroth AG, RE-A 92703/03.2015

L2

Axial piston variable pump | A10VO series 52 and 53 23


EP.ED / EK.ED with electro-hydraulic pressure control




EP.ED / EK.ED with electro-hydraulic pressure control


The ED valve is set to a certain pressure by a specified

Circuit diagram EK.ED

variable solenoid current.

When a change is made at the consumer (load pressure),


the position of the control piston will shift.
This causes an increase or decrease in the pump swivel
angle (flow) in order to maintain the electrically set pressure level.
The pump thus only delivers as much hydraulic fluid as the
consumers can take. The pressure can be set steplessly by
the solenoid current.
As the solenoid current signal drops towards zero, the
pressure will be limited to pmax by an adjustable hydraulic
pressure cut-off (negative characteristic curve, e.g. for fan

L1

drives ). A PWM signal is used to control the solenoid.


For further information and technical data of the solenoids
for ED(ER) control please refer to pages18 to21.
Circuit diagram EP.ED
X

L2

1 The metering orifice (control block) and the line is not


included in the delivery contents.

L1

L2

RE-A 92703/03.2015, Bosch Rexroth AG

24

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 10

Dimensions, size 10
DR Pressure control; centering flange SAE version

max. 4.33 (110)


(5

6)

2.87 (73)

20

L
45

Flange
ISO 3019-1

45

DIA 3.250
3.248
0
( 82.55 -0.054)

35
0. )
(9

2.11 (53.5)
2.20 (56)

0.43 (11)

2.

0.43 (11)
0.25 (6.4)

L1
4.19 (106.4)
5.28 (134)

0.94 (24)
5.83 (148)
7.09 (180)

View Y
Valve mounting
for clockwise
rotation

View Y
Valve mounting for
counter-clockwise
rotation

1.13 1.13
(28.6) (28.6)

1.13 1.13
(28.6) (28.6)

2.00 (51) 2.00 (51)

2.00 (51) 2.00 (51)

Bosch Rexroth AG, RE-A 92703/03.2015

Axial piston variable pump | A10VO series 52 and 53 25


Dimensions, size 10




Splined shaft 3/4 in (SAE J744)

Splined shaft 5/8 in (SAE J744)


U 9T 16/32DP1)

S 11T 16/32DP

1)

0.94 (23.8)

0.35 (14)
0.19 (5)

0.87 (22)

1/4-20UNC-2B2) 4)

1.18 (30)

Centering 3)
R3 15x6.7
DIN 332

0.87 (21)
1.50 (38)

0.87 (22)

Dimensions [in (mm)]

0.62
(15.8)

1.25 (31.8)

Parallel keyed shaft ISO 3019-1


K 19-1

1.13 (28.6)
0.01
(2.5)

Centering 3)
R 0.12x0.26
DIN 332

1.61 (41)

Ports
B

Working port

Standard

Size4)

pmax abs
[psi (bar)]5)

State8)

ISO 11926

1 1/16-12UNF-2B; 0.79 (20) deep

4600 (315)

Suction port

ISO 11926

1 1/16-12UNF-2B; 0.79 (20) deep

75 (5)

Drain port

ISO 119266)

9/16-18UNF-2B; 0.39 (10) deep

30 (2)

O7)

L1

Drain port

ISO 11926

9/16-18UNF-2B; 0.39 (10) deep

30 (2)

X7)

X without
adapter

Control pressure

ISO 11926

7/16-20UNF-2B; 0.45 (11.5) deep

4600 (315)

1)

2)
3)

4)

Key
width
0.188 (4.76+0.025)
0.187

0.87 (22)

DIA 0.750
0.749 (19.05

0.833
0.827
(21.1+0.05
-0.1 )

+0.009
-0.004 )

1.30 (33)

Involute spline according to ANSIB92.1a, 30 pressure angle, flat


root, side fit, tolerance class5
Thread according to ASME B1.1
Coupling axially secured, e.g. with a clamp coupling or radially
mounted clamping screw
Observe the project planning notes on page 68 concerning the
maximum tightening torques.

6)

5)

6)
7)

8)

Depending on the application, momentary pressure spikes can occur.


Keep this in mind when selecting measuring equipment and fittings
The spot face can be deeper than as specified in the standard.
Depending on the installation position, L or L1 must be connected
(also see installation instructions starting on page 64).
O = Must be connected (plugged on delivery) X = Plugged (in
normal operation)
RE-A 92703/03.2015, Bosch Rexroth AG

DRG Pressure control, remotely operated1)

3.74 (95)
4.02 (102)

DFR/DFR1 Pressure, flow control1)

1.57
(40)

5.75 (146)

L1 7.05 (179)

1)

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 10

Valve mounting for clockwise or counter-clockwise rotation see


page 24

Bosch Rexroth AG, RE-A 92703/03.2015

1.57
(40)

5.75 (146)

L1 7.05 (179)

3.74 (95)
4.02 (102)

26

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 27


Dimensions, size 18




Dimensions, size 18
DR Pressure control; clockwise rotation, series 53
Port plate 61

L1

09

45

(2
.5

5)
1.

5)

(6

1.

2.

2.

2.48 (63)

42

42

(6

45

L2

3.27 (83)
6.14 (156)
max. 7.20 (183)

3.250
DIA 3.248

0.

0.43 (11)

L1

0
(82.55- 0.054
)

Flange
ISO 3019-1

3.27 (83)
0.39 (10)
0.96
(24.5)
4.80 (122)
2.83 (72)

0.31 (7.8)

4.19 (106.4)
5.35 (136)

20
47.6

DIA 1.26
(32)

2.31 (58.7)

View X1)

B
1.19
(30.2)

Detail Z

0.31 (7.8)

1.87 (47.6)
DIA 0.79 (20)

Port plate 62
3.27 (83)
0.39 (10)
0.96 (24.5)

L1

0.87
(22.2)

2.31 (58.7)

DIA 1.26
(32)

DIA 3.250
3.248
(82.55 - 00.054 )

1.30
(33)

View Y1)

Flange
ISO 3019-1

0.87 (22.2)

1.26
(32)

S
5.63 (143)
6.70 (170)

1)

30.2

2.22 (56.5) 2.22 (56.5)

Dimensions of working ports turned through 180 for counter-clockwise rotation

RE-A 92703/03.2015, Bosch Rexroth AG

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 18

28

Splined shaft 3/4 in (SAE J744)

Splined shaft 3/4 in (SAE J744)


R 11T 16/32DP1)2)

S 11T 16/32DP

1)

0.55 (14)
1/4-20UNC-2B4)5)

0.35 (14)

0.20 (5)

0.87
(22)

0.20 (5)
0.87 (22)

1/4-20UNC-2B4) 5)

1.18 (30)

Usable shaft

0.83 (21)

length

0.83 (21)

1.50 (38)

1.50 (38)

Splined shaft 5/8 in (SAE J744)


U 9T 16/32DP1)

Centering 3)
R3 0.12x0.26
DIN 332

0.87 (22)

0.94 (23.8)

0.62
(15.8)

1.25 (31.8)

Ports

Standard

Size5)

pmax abs
[psi (bar)]6)

State10)

Working port (Standard pressure series)


Fastening thread

SAE J518
ASME B1.1

3/4 in
3/8-16UNC-2B; 0.75 (19) deep

4600 (315)

Suction port (standard pressure series)


Fastening thread

SAE J518
ASME B1.1

1 1/4 in
7/16-14UNC-2B; 0.79 (20) deep

75 (5)

Drain port

DIN 119267)

3/4-16UNF-2B; 0.47 (12) deep

30 (2)

O8)

L1, L2

Drain port

DIN 11926

3/4-16UNF-2B; 0.47 (12) deep

30 (2)

X8)

Control pressure

DIN 11926

7/16-20UNF-2A; 0.45 (11.5) deep

4600 (315)

L
9)

1)

2)

3)
4)
5)

7)

Involute spline according to ANSIB92.1a, 30 pressure angle, flat


root, side fit, tolerance class5
Splines according to ANSI B92.1a, run out of spline is a deviation
from standard.
Center bore according to DIN 332
Thread according to ASME B1.1
Observe the project planning notes on page 68 concerning the
maximum tightening torques.

Bosch Rexroth AG, RE-A 92703/03.2015

Depending on the application, momentary pressure spikes can occur.


Keep this in mind when selecting measuring equipment and fittings
7) The spot face can be deeper than as specified in the standard.
8) Depending on the installation position, L, L1 or L2 must be
connected (also see installation instructions starting on page 64).
9) Only series 53
10) O= Must be connected (plugged on delivery) X= Plugged (in
normal operation)
6)

Axial piston variable pump | A10VO series 52 and 53 29


Dimensions, size 18




DRG Pressure controller, remote controlled, series 53

max. 7.20 (183)


4.45 (113)

EP.D. / EK.D. Electro-proportional control, series 53

8.60 (218.5)
4.45 (113)

2.44 (62)

L2

DRF/DRS Pressure and flow control, series 53

max. 7.20 (183)


4.45 (113)

L2

L1

L2

L2

ED7. / ER7. Electro-prop. pressure control, series 53

8.42 (214)

8.86 (225)
4.45 (113)

X 2.44 (62)
4.80 (122)1)

L1

4.80 (122)
4.45 (113)
4.17 (106)

LA.D. Pressure, flow and power control, series 53

1)

8.66 (220)

L1

4.80 (122)
4.17 (106)

L1

EP.ED. / EK.ED. Electro-prop. control, series 53

2.44 (62)

2.44 (62)
4.80 (122)
4.17 (106)

4.80 (122)
4.17 (106)

L1

4.80 (122)
4.33 (110)

Dimensions [in (mm)]

L2

L1
L

L2

ER7.: 6.18 (157 mm) if using an intermediate plate pressure controller


RE-A 92703/03.2015, Bosch Rexroth AG

30

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 28

Dimensions, size 28
DR Hydraulic pressure controller; clockwise rotation, series 522)
Port plate 61

3.54 (90)
0.47 (12)

Flange
ISO 3019-1

45

4.88 (123.5)

0.25 (6.3)

69

4.000
DIA 3.998
0
(101.6 -0.054
)

2.87 (73)
2.60 (66)

0.55 (14.3)

0.37 (9.5)

L1

1.06 (27)
0.31 (7.9)

5.75 (146)
6.77 (172)

6.79 (170)
max. 8.25 (209.5)

0.87 (22.2)

1.19 (30.2)
1.87 (47.6)
0.79 (20)

Port plate 62

max. 8.25 (209.5)

0.25 (6.3)
Flange
ISO 3019-1

1.30
(33)

Detail Z

1.30
(33)

View Y1)

0.87 (22.2)

1.26
(32)

4.000
DIA 3.998
0
(101.6 -0.054
)

L
2.31 (58.7)

0.47 (12)
0.37 (9.5)

3.54 (90)

S
1.06 (27)

1)
2)

L1

1.19 (30.2)
6.30 (160)

Dimensions of working ports turned through 180 for counter-clockwise rotation


Primary dimensions for pump apply to series 52 and 53

Bosch Rexroth AG, RE-A 92703/03.2015

47.6

2.31 (58.7)
1.26 (32)

20

View X1)

2.60 (66)

2.60 (66)

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 31


Dimensions, size 28




Splined shaft 7/8 in (SAE J744)

Splined shaft 7/8 in (SAE J744)


R 13T 16/32DP1)2)

S 13T 16/32DP

1.30 (33.1)
0.63
(16)
0.20(5)

1/4-20UNC-2B3)4)

1/4-20UNC-2B3) 4)

1)

0.63 (16)

Usable

0.99
(25.1)

0.20 (5)

0.99 (25)

shaft length

1.61 (41)

1.61 (41)
Parallel keyed shaft (ISO 3019-1)

Tapered with woodruff key (ISO 3019-1)

K 22-1

C
125:1000

0.130
0.126 (3.2 -0.1)

B
1.10
(28)

0.251
0.250 (6.35 +0.025)

2.19 (55.6)

Standard

Size4)

pmax abs
[psi (bar)]5)

State9)

Working port (Standard pressure series)


Fixingthread

SAE J518
ASME B1.1

3/4 in
3/8-16UNC-2B; 0.75 (19) deep

4600 (315)

Suction port (standard pressure series)


Fastening thread

SAE J518
ASME B1.1

1 1/4 in
7/16-14UNC-2B; 0.79 (20) deep

75 (5)

Drain port

ISO 119266)

3/4-16UNF-2B; 12 deep

30 (2)

O7)

L1, L28)

Drain port

ISO 119266)

3/4-16UNF-2B; 12 deep

30 (2)

X7)

Control pressure

ISO 11926

7/16-20UNF-2B; 11.5 deep

4600 (315)

1)

2)

3)
4)

5)

0.57 (14.4)
A

0.16 (4)
0.118
0.110 (3 -0.2)

1.62 (41.3)

Ports

0.75 (19)

0.251
+0.025
)
0.250(6.35

0.8575
DIA 0.8570

(21.774 +0.006
-0.006 )

0.251 (6.35+0.25)
0.250

0.20
(5)

5/8-18UNF-2A1) 2)

0.63 (16)

0.98 (25)

1/4-20UNC-2B 3) 4)

DIA 0.8750
0.8742 (22.225 -0.02)

0.9843
0.9764
(25 -0.2 )

1.31 (33.3)

Involute spline according to ANSIB92.1a, 30 pressure angle, flat


root, side fit, tolerance class5
Splines according to ANSI B92.1a, run out of spline is a deviation
from standard.
Thread according to ASME B1.1
Observe the project planning notes on page 68 concerning the
maximum tightening torques.
Depending on the application, momentary pressure spikes can occur.
Keep this in mind when selecting measuring equipment and fittings

6)
7)

8)
9)

The spot face can be deeper than as specified in the standard.


Depending on the installation position, L, L1 or L2 must be connected (also see installation instructions starting on page 64).
Only for series 53
O = Must be connected (plugged on delivery) X = Plugged
(innormal operation)

RE-A 92703/03.2015, Bosch Rexroth AG

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 28

DRG Pressure controller, remote controlled, series 52

max. 8.25 (209.5)


5.49 (139.5)

EP.D. / EK.D. Electro-proportional control, series 53

8.82 (224)
5.59 (140)

4.86 (123.5)
4.21 (107)

2.48 (63)

2.48 (63)
X

max. 8.25 (209.5)


5.49 (139.5)

EP.ED. / EK.ED. Electro-prop. control, series 53

9.45 (240)

L1

5.12 (130)
4.60 (117)

4.86 (123.5)
4.21 (107)

2.48 (63)

L2

L1

DFR/DFR1 Pressure and flow control, series 52

L1

5.12 (130)
4.49 (114)

32

L2

S
L1

LA.D. Pressure, flow and power control, series 53

2.48 (63)

9.45 (240)

L1
5.12 (130)
4.49 (114)

L
S

5.12 (130)1)

9.09 (231)
5.51 (140)

ED7. / ER7. Electro-prop. Pressure control, series 52

S
L2

1)

ER7.: 6.26 inch (159 mm) if using an intermediate plate pressure


controller

Bosch Rexroth AG, RE-A 92703/03.2015

L1

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 33


Dimensions, size 45




Dimensions, size 45
DR Hydraulic pressure controller; Clockwise rotation, series 522)
Port plate 61
3.90 (99)
0.25 (6.3)

0.47 (12)
1.18 (30)
5.18 (131.5)

L1

Flange
ISO 3019-1

45

78

DIA 4.000
3.998
0
(101.6 -0.054
)

14.3
3.03 (77)

0.37 (9.5)

2.70 (68.5)

7.44 (189)
max. 8.68 (220.5)

5.75 (146)
6.77 (172)

Port plate 62

L1

0.98 (25)

2.
(5 06
2.4
)

1.41
(35.7)

1.
(26 03
.2)

1.
(3 41
5.7
)

30

View Y1)

Detail Z
2.06 (52.4)

7.01 (178)
8.31 (211)

2.7
5(
69
1.50 (38)
.9

1.50
(38)

S
2.75 (69.9)

4.000
DIA 3.998
0
(101.6 -0.054
)

Flange
ISO 3019-1

View X1)

0.98 (25)

0.37 (9.5)
0.25 (6.3)

max. 8.68 (220.5)


5.93 (150.5)
3.90 (99)
0.47 (12)
1.18 (30)

1.50
(38)

B
30
1.50
(38)

1.03
(26.2)

3.54 (90)
1)
2)

3.54 (90)

Dimensions of working ports turned through 180 for counter-clockwise rotation


Primary dimensions for pump apply to series 52 and 53

Ports see page35




RE-A 92703/03.2015, Bosch Rexroth AG

34

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 45

Splined shaft 1 in SAE J744

Splined shaft 1 in SAE J744


R 15T 16/32DP1)2)

S 15T 16/32DP

1)

0.63 (16)

1/4-20UNC-2B

0.63 (16)

1/4-20UNC-2B3) 4)

3) 4)

1.49 (38)
0.20(5)

0.20 (5)

1.16
(29.5)

Usable
shaft length

1.18 (30)

1.81 (45.9)

1.81 (45.9)

Splined shaft 7/8 in SAE J744

Splined shaft 7/8 in SAE J744

U 13T 16/32DP

W 13T 16/32DP1)

1)

1/4-20UNC-2B3) 4)

1/4-20UNC-2B3) 4)

1.30 (33.1)
0.63 (16)
0.20 (5)

0.63 (16)

Usable

0.99
(25.1)

0.20 (5)

0.98 (25)

shaft length

1.61 (41)

1.61 (41)

Parallel keyed shaft (ISO 3019-1)

Tapered with woodruff key (ISO 3019-1)

K 25-1

0.57 (14.4)
A

0.16 (4)
0.13 (3.2)

1.81 (46)

Bosch Rexroth AG, RE-A 92703/03.2015

B
1.18
(30)
2.43 (61.8)

0.251
0.250 (6.35 +0.025)
0.130
0.126 (3.2 -0.1)

0.75 (19)

0.251
+0.025
)
0.250(6.35

(21.774 +0.006
-0.006 )

0.20
(5)

0.8575
DIA 0.8570

0.251 (6.35+0.25)
0.250

5/8-18UNF-2A3) 4)

125:1000

0.63 (16)

0.98 (25)

(25.4 -0.03)
DIA 1.000
0.998

1.1102
1.1024
(28.2 -0.2 )

1/4-20UNC-2B 3) 4)

1.50 (38.1)

Dimensions [in (mm)]

Ports

Standard

Size4)

pmax abs
[psi (bar)]5)

State9)

Working port (Standard pressure series)


Fastening thread

SAE J518
ASME B1.1

1 in
3/8-16UNC-2B; 0.71 (18) deep

4600 (315)

Suction port (standard pressure series)


Fastening thread

SAE J518
ASME B1.1

1 1/2 in
1/2-13UNC-2B; 0.87 (22) deep

75 (5)

Drain port

ISO 119266)

7/8-14UNF-2B; 0.51 (13) deep

30 (2)

O7)

Drain port

ISO 11926

7/8-14UNF-2B; 0.51 (13) deep

30 (2)

X7)

Control pressure

ISO 11926

7/16-20UNF-2A; 0.45 (11.5) deep 4600 (315)

L
L1, L2
X

1)

2)

3)
4)

5)

Axial piston variable pump | A10VO series 52 and 53 35


Dimensions, size 45




8)

6)

Involute spline according to ANSIB92.1a, 30 pressure angle, flat


root, side fit, tolerance class5
Splines according to ANSI B92.1a, run out of spline is a deviation
from standard.
Thread according to ASME B1.1
Observe the project planning notes on page 68 concerning the
maximum tightening torques.
Depending on the application, momentary pressure spikes can occur.
Keep this in mind when selecting measuring equipment and fittings

6)
7)

8)
9)

The spot face can be deeper than as specified in the standard.


Depending on the installation position, L, L1 or L2 must be connected (also see installation instructions starting on page 64).
Only series 53
O = Must be connected (plugged on delivery) X = Plugged
(in normal operation)

RE-A 92703/03.2015, Bosch Rexroth AG

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 45

DRG Pressure controller, remote controlled, series 52

max. 8.68 (220.5)


5.93 (150.5)

EP.D. / EK.D. Electro-proportional control, series 53

8.98 (228)
5.75 (146)

5.18 (131.5)
4.53 (115)

2.68 (68)

L1
L

2.68
(68)
X

5.22 (132.5)
4.57 (116)

36

1.38
(35)

L1

S
L2

DFR/DFR1 Pressure and flow control, series 52

max. 8.68 (220.5)


5.93 (150.5)

EP.ED. / EK.ED. Electro-prop. control, series 53

L1
L

3.35 (85) 1.42


(36) L
1

9.68 (246)

5.24 (133)
4.68 (119)

5.18 (131.5)
4.53 (115)

2.68 (68)

L2

LA.D. Pressure, flow and power control, series 53

5.24 (133)
4.57 (116.4)

2.68 (68)

9.84 (250)

L1

L2

1)

ER7.: 167 mm if using an intermediate plate pressure controller

Bosch Rexroth AG, RE-A 92703/03.2015

L1

5.20 (132)1)

9.25 (235)
5.75 (146)

ED7. / ER7. Electro-prop. Pressure control, series 52

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 37


Dimensions, size 60




Dimensions, size 60
DR Hydraulic pressure controller; Clockwise rotation, mounting flange C series 52
Port plate 61
max. 8.68 (220.5)
4.61 (117)

L1

Flange
ISO 3019-1

L
45
8.

5)

DIN 4.000
3.998
0
(101.6 -0.054
)

2.99 (78)

(7

0.56 (14.3)
3.42 (87)

1.57
(40)

5.39 (137)

0.37
(9.5)

0.59 (15)

5.75 (146)
6.77 (172)

8.19 (208)

View X1)

52.4

3.06 (77.8)
1.97 (50)

25

Detail Z

max. 8.68 (220.5)


4.61 (117)
1.57 (40)

0.25
(6.3)
Flange
ISO 3019-1

1.03 (26.2)
1.81 (46)

View Y1)

1.11
(26.2)

1.97
(50)
3.06 (77.8)

DIN 4.000
3.998
0
(101.6 -0.054
)

S
0.59
(15)

1)

2.06 (52.4)

0.37
(9.5)

0.98 (25)

Port plate 62

1.67 (42.9)
1.30
(33)

7.93 (201.5)

1.69 (42.9)

9.43 (239.5)

2.83 (72)

2.83 (72)

Dimensions of working ports turned through 180 for counter-clockwise rotation

Ports and footnote see page 42




RE-A 92703/03.2015, Bosch Rexroth AG

38

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 60

Dimensions, size 60
DR Hydraulic pressure controller; Clockwise rotation, mounting flange D series 52
Port plate 61

L1

45
8.
(7
09
3.

5)

5.83 (148)

DIA 5.0000
4.9975
0
(127 -0.063)

56 3)
0. 4.
(1

Flange
ISO 3019-1

4.51 (114.5)
3.07 (78)
3.43 (87)

1.57 (40)

0.24 (6)

5.41 (137.4)

0.50
(12.7)

max. 8.68 (220.5)


4.61 (117)

4.51 (114.5)
5.75 (146)

0.59 (15)
8.19 (208)

View X1)

3.06 (77.8)
1.97 (50)

0.98 (25)
2.96
(52.4)

B
1.67 (42.9)
Detail Z

Port plate 62

1.57 (40)

2.06 (52.4)
0.98 (25)

max. 8.68 (220.5)


4.61 (117)
0.50 (12.7)

1.30
(33)

1.03 (26.2)
1.81
(46)

View Y1)

Flange
ISO 3019-1

1.11 (26.2)

DIA 5.0000
4.9975
0
(127 -0.063)

1.97
(50)
3.06 (77.8)

S
0.59 (15)

1)

7.93 (201.5)
9.43 (239.5)

1.67
(42.9)

Dimensions of working ports turned through 180 for counter-clockwise rotation

Ports and footnote see page 42


Bosch Rexroth AG, RE-A 92703/03.2015

2.83 (72)

2.83 (72)

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 39


Dimensions, size 63




Dimensions, size 63
DR Hydraulic pressure controller; Clockwise rotation, mounting flange C series 53
Port plate 61
max. 8.68 (220.5)
4.55 (115.5)

L1

0.56 (14.3)
3.50 (89)

5)

3.

3.46 (88)

3.

05

(7

7.

(7
9

43

11

5.53 (140.4)

DIA 4.000
3.998

(101.6-0.054)

Flange
ISO 3019-1

4.37 (111)

L1

45

L2
5.75 (146)
5.91 (172)

8.19 (208.2)

3.06 (77.8)
1.97 (50)

0.98 (25)
2.06
(52.4)

View X1)

S
1.67 (42.9)
Detail Z
2.06 (52.4)
0.98 (25)

Port plate 62
max. 8.68 (220.5)
4.55 (115.5)
1.54 (39)

1.81
(46)

1.03 (26.2)

View Y1)

(101.6

1.97
(50)

DIA 4.000
3.998

0
-0.054

Flange
ISO 3019-1

1.03 (26.2)

3.06 (77.8)

0.37 (9.5)
0.25 (6.3)

1.30
(33)

S
0.59 (15)
4.55 (115.5)
7.93 (201.5)
9.43 (239.5)
1)

1.69
(42.9)

2.83 (72) 2.83 (72)

Dimensions of working ports turned through 180 for counter-clockwise rotation

Ports and footnote see page 42




RE-A 92703/03.2015, Bosch Rexroth AG

40

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 63

Dimensions, size 63
DR Hydraulic pressure controller; Clockwise rotation, mounting flange D series 53
Port plate 61
max. 8.68 (220.5)

L1

L1

)
(7
9

11

3.

DIA 5.0000
4.9975
0
(127 -0.063 )

43
45

5
4

45

L2

0.59 (15)

5.75 (146)
3.50 (89)
3.46 (88)

4.55 (115.5)
1.54 (39)

5.51 (140)
4.37 (111)
0.
55
4.51 (114.5)
(1
4)
3.
05
(7
7.
5)

0.50 (12.7)
0.25 (6.3)
Flange
ISO 3019-1

4.51 (114.5)
5.75 (146)
5.91 (150)

8.19 (208)

3.06 (77.8)
1.97 (50)

0.98 (25)
2.06 (52.4)

View X1)

S
Port plate 62
max. 8.68 (220.5)

Detail Z

1)

View Y1)

50
77.8

26.2

S
0.59 (15)

4.55 (115.5)
7.93 (201.5)
9.43 (239.5)

1.69
(42.9)

Dimensions of working ports turned through 180 for counter-clockwise rotation

Ports and footnote see page 42


Bosch Rexroth AG, RE-A 92703/03.2015

1.03 (26.2)

1.81
(46)

L1

52.4

1.54 (39)

DIA 5.0000
4.9975
0
(127 -0.063 )

0.50 (12.7)
0.25 (6.3)
Flange
ISO 3019-1

25

4.55 (115.5)

1.67
(42.9)
1.30
(33)

72

72

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 41


Dimensions, nominal size 60/63

Splined shaft 1 1/4 in SAE J744

Splined shaft 1 1/4 in SAE J744


R 14T 12/24DP1)2)

S 14T 12/24DP

1)

5/16-18UNC-2B3) 4)

3) 4)

1.87 (47.5)

5/16-18UNC-2B

0.75 (19)
0.20 (5)

0.75 (19)
0.20 (5)

Usable

1.56
(39.5)

1.50 (38)

shaft length

2.18 (55.4)

2.18
(55.4)

Splined shaft 1 in SAE J744

Splined shaft 1 in SAE J744

U 15T 16/32DP

W 15T 16/32DP1)

1)

1/4-20UNC-2B3) 4)

1/4-20UNC-2B3) 4)

1.49 (38)
0.63 (16)
0.20 (5)

0.63 (16)

Usable

0.98
(25)

0.20 (5)

1.14 (29)

shaft length

1.81 (45.9)

1.81 (45.9)

Parallel keyed shaft (ISO 3019-1)

Tapered with woodruff key (ISO 3019-1)

K 32-1

125:1000
0.56 (14.1)
A

0.16 (4)
0.12 (3)

2.18 (55.4)

B
1.18
(30)

0.3136
0.3126 (7.94 +0.025)
0.1394
0.1354 (3.54 -0.1)

1-12UNF-2A3) 4)

1.2408
DIA 1.2403

0.20
(5)

(31.51 +0.006
-0.006 )

0.93 (23.6)
0.3136 (7.94+0.25)
0.3126

0.3136
0.3126 (7.94 +0.025)

0.75 (19)

1.37
(34.91)

1/4-20UNC-2B 3) 4)

DIA 1.250
1.248

1.3898
1.3819
(35.3 -0.2 )

(31.75 -0.03)

1.87 (47.5)

2.61 (66.4)

Footnote see page 42

RE-A 92703/03.2015, Bosch Rexroth AG

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 63

42

Ports

Standard

Size4)

pmax abs
[psi (bar)]5)

State9)

Working port (Standard pressure series)


Fastening thread

SAE J518
ASME B1.1

1 in
3/8-16UNC-2B; 0.71 (18) deep

4600 (315)

Suction port (standard pressure series)


Fastening thread

SAE J518
ASME B1.1

2 in
1/2-13UNC-2B; 0.87 (22) deep

75 (5)

Drain port

ISO 119266)

7/8-14UNF-2B; 0.51 (13) deep

30 (2)

O7)

L1, L28)

Drain port

ISO 119266)

7/8-14UNF-2B; 0.51 (13) deep

30 (2)

X7)

Control pressure

ISO 11926

7/16-20UNF-2A; 0.45 (11.5) deep

4600 (315)

1)

2)

3)
4)

5)

Involute spline according to ANSIB92.1a, 30 pressure angle, flat


root, side fit, tolerance class5
Splines according to ANSI B92.1a, run out of spline is a deviation
from standard.
Thread according to ASME B1.1
Observe the project planning notes on page 68 concerning the
maximum tightening torques.
Depending on the application, momentary pressure spikes can occur.
Keep this in mind when selecting measuring equipment and fittings

Bosch Rexroth AG, RE-A 92703/03.2015

6)
7)

8)
9)

The spot face can be deeper than as specified in the standard.


Depending on the installation position, L, L1 or L2 must be connected (also see installation instructions starting on page 64).
Only series 53
O = Must be connected (plugged on delivery) X = Plugged
(in normal operation)

Axial piston variable pump | A10VO series 52 and 53 43


Dimensions, size 63




DRG Pressure controller, remote controlled, series 52

5.39 (137)
4.76 (121)

L1

X 2.56 (65)

L1

9.49 (241)
5.94 (151)
4.55 (115.5)

2.55 1.40

DFR/DFR1 Pressure and flow control, series 52

max. 8.68 (220.5)


5.93 (150.5)
X

X 2.56 (65)
5.39 (137)
4.76 (121)

L1

X (64.8)(35.6)
L1
5.53 (140.4)
4.92 (125)
4.88 (123.9)

max. 8.68 (220.5)


5.93 (150.5)

EP.D. / EK.D. Electro-proportional control, series 53

L2

EP.ED. / EK.ED. Electro-prop. control, series 53

L1

1.42
3.23 (82) (36)

9.86 (250.5)
4.55 (115.5)

L1

5.53 (140.4)
4.92 (125)

Dimensions [in (mm)]

S
L2

LA.D. Pressure, flow and power control, series 53

5.51 (140)
5.04 (128)
4.88 (124)

1)

2.56 (65)

9.88 (251)

L1
L

L1
L

5.39 (137)1)

9.72 (247)
5.91 (150)

ED7. / ER7. Electro-prop. Pressure control, series 52

L1
L

L2

ER7.: 6.77 inch (172 mm) if using an intermediate plate pressure


controller
RE-A 92703/03.2015, Bosch Rexroth AG

44

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 72

Dimensions, size 72
DR Hydraulic pressure controller; Clockwise rotation, mounting flange C series 53
Port plate 61
max. 8.68 (220.5)
4.55 (115.5)

L1

0.56 (14.3)
3.50 (89)

5)

3.

3.46 (88)

3.

05

(7

7.

(7
9

43

11

5.53 (140.4)

DIA 4.000
3.998

(101.6-0.054)

Flange
ISO 3019-1

4.37 (111)

L1

45

L2
5.75 (146)
5.91 (172)

8.19 (208.2)

3.06 (77.8)
1.97 (50)

0.98 (25)
2.06
(52.4)

View X1)

S
1.67 (42.9)
Detail Z
2.06 (52.4)
0.98 (25)

Port plate 62
max. 8.68 (220.5)
4.55 (115.5)
1.54 (39)

1.81
(46)

1.03 (26.2)

View Y1)

(101.6

1.97
(50)

DIA 4.000
3.998

0
-0.054

Flange
ISO 3019-1

1.03 (26.2)

3.06 (77.8)

0.37 (9.5)
0.25 (6.3)

1.30
(33)

S
0.59 (15)
4.55 (115.5)
7.93 (201.5)
9.43 (239.5)
1)

1.69
(42.9)

Dimensions of working ports turned through 180 for counter-clockwise rotation

Bosch Rexroth AG, RE-A 92703/03.2015

2.83 (72) 2.83 (72)

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 45


Dimensions, size 72




Dimensions, size 72
DR Hydraulic pressure controller; Clockwise rotation, mounting flange D series 53
Port plate 61
max. 8.68 (220.5)

L1

L1

)
(7
9

11

3.

DIA 5.0000
4.9975
0
(127 -0.063 )

43
45

5
4

45

L2

0.59 (15)

5.75 (146)
3.50 (89)
3.46 (88)

4.55 (115.5)
1.54 (39)

5.51 (140)
4.37 (111)
0.
55
4.51 (114.5)
(1
4)
3.
05
(7
7.
5)

0.50 (12.7)
0.25 (6.3)
Flange
ISO 3019-1

4.51 (114.5)
5.75 (146)
5.91 (150)

8.19 (208)

3.06 (77.8)
1.97 (50)

0.98 (25)
2.06 (52.4)

View X1)

S
Detail Z

Port plate 62
max. 8.68 (220.5)

1.67
(42.9)
1.30
(33)

1.81
(46)

1.03 (26.2)

50
77.8

26.2

S
0.59 (15)

1)

View Y1)

L1

52.4

1.54 (39)

DIA 5.0000
4.9975
0
(127 -0.063 )

0.50 (12.7)
0.25 (6.3)
Flange
ISO 3019-1

25

4.55 (115.5)

4.55 (115.5)
7.93 (201.5)
9.43 (239.5)

1.69
(42.9)

72

72

Dimensions of working ports turned through 180 for counter-clockwise rotation

RE-A 92703/03.2015, Bosch Rexroth AG

46

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 72

Dimensions, size 72
DR Hydraulic pressure controller; Clockwise rotation, mounting flange R series 53

max. 8.68 (220.5)

L1

L1

)
(7
9

11

3.

DIA 5.0000
4.9975
0
(127 -0.063 )

43
45

5
4

45

L2

0.59 (15)

5.75 (146)
3.50 (89)
3.46 (88)

4.55 (115.5)
1.54 (39)

5.51 (140)
4.37 (111)
0.
55
4.51 (114.5)
(1
4)
3.
05
(7
7.
5)

0.50 (12.7)
0.25 (6.3)
Flange
ISO 3019-1

4.51 (114.5)
5.75 (146)
5.91 (150)

3.06 (77.8)
1.97 (50)

0.98 (25)
2.06 (52.4)

8.19 (208)

S
1.67
(42.9)
1.30
(33)

max. 8.68 (220.5)

1.81
(46)

1.03 (26.2)

50
77.8

S
0.59 (15)

1)

26.2

L1

52.4

1.54 (39)

DIA 5.0000
4.9975
0
(127 -0.063 )

0.50 (12.7)
0.25 (6.3)
Flange
ISO 3019-1

25

4.55 (115.5)

4.55 (115.5)
7.93 (201.5)
9.43 (239.5)

1.69
(42.9)

Dimensions of working ports turned through 180 for counter-clockwise rotation

Bosch Rexroth AG, RE-A 92703/03.2015

72

72

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 47


Dimensions, size 72




Splined shaft 1 1/4 in SAE J744

Splined shaft 1 1/4 in SAE J744


R 14T 12/24DP1)2)

S 14T 12/24DP

1)

0.75 (19)

5/16-18UNC-2B

0.75 (19)

5/16-18UNC-2B3) 4)

3) 4)

1.87 (47.5)
0.20 (5)

0.20 (5)

Usable

1.56
(39.5)

1.50 (38)

shaft length

2.18 (55.4)

2.18
(55.4)

Splined shaft 1 in SAE J744

Splined shaft 1 in SAE J744

U 15T 16/32DP

W 15T 16/32DP1)

1)

1/4-20UNC-2B3) 4)

1/4-20UNC-2B3) 4)

1.49 (38)
0.63 (16)
0.20 (5)

0.63 (16)

Usable

0.98
(25)

0.20 (5)

1.14 (29)

shaft length

1.81 (45.9)

1.81 (45.9)

Ports

Size4)

pmax abs
psi [bar]5)

State8)

Working port (Standard pressure series)


Fastening thread

SAE J518
ASME B1.1

1 in
3/8-16UNC-2B; 0.71 (18) deep

4600 (315)

Suction port (standard pressure series)


Fastening thread

SAE J518
ASME B1.1

2 in
1/2-13UNC-2B; 0.87 (22) deep

75 (5)

Drain port

ISO 119266)

7/8-14UNF-2B; 0.51 (13) deep

30 (2)

O7)

L1, L2

Drain port

ISO 11926

7/8-14UNF-2B; 0.51 (13) deep

30 (2)

X7)

Control pressure

ISO 11926

7/16-20UNF-2A; 0.45 (11.5) deep

4600 (315)

1)

2)

3)
4)

5)

Standard

Involute spline according to ANSIB92.1a, 30 pressure angle, flat


root, side fit, tolerance class5
Splines according to ANSI B92.1a, run out of spline is a deviation
from standard.
Thread according to ASME B1.1
Observe the project planning notes on page 68 concerning the
maximum tightening torques.
Depending on the application, momentary pressure spikes can occur.
Keep this in mind when selecting measuring equipment and fittings

6)

6)
7)

8)

The spot face can be deeper than as specified in the standard.


Depending on the installation position, L, L1 or L2 must be connected (also see installation instructions starting on page 64).
O = Must be connected (plugged on delivery) X = Plugged
(in normal operation)

RE-A 92703/03.2015, Bosch Rexroth AG

DRG Pressure controller, remote controlled, series 53

max. 8.68 (220.5)


5.92 (150.5)

EP.D. / EK.D. Electro-proportional control, series 53

9.49 (241)
5.94 (151)
4.55 (115.5)

2.56 (65)

5.53 (140.5)
4.88 (124)

L2

max. 8.68 (220.5)


5.92 (150.5)

L1

5.51 (140)
5.04 (128)
4.88 (124)

L2

ED7. / ER7. Electro-prop. pressure control, series 53

2.56 (65)

9.86 (250.5)

L1

L2

ER7.: 6.91 inch (175.5 mm) if using an intermediate plate pressure


controller

Bosch Rexroth AG, RE-A 92703/03.2015

LA.D. Pressure, flow and power control, series 53

1.42
3.23 (82) (36)

L2

9.86 (250.5)
4.55 (115.5)

2.56 (65)

L2

9.72 (247)
5.91 (150)

EP.ED. / EK.ED. Electro-prop. control, series 53

5.53 (140.5)
4.88 (124)

5.53 (140.4)
4.92 (125)
4.88 (123.9)

DRF/DRS Pressure and flow control, series 53

2.55 1.40

X (64.8)(35.6)
L1

5.53 (140.4)
4.92 (125)

1)

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 72

5.53 (140.5)1)

48

L2

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 49


Dimensions, size 85




Dimensions, size 85
DR Hydraulic pressure controller; Clockwise rotation, mounting flange C series 52
Port plate 61
max. 9.53 (242)
5.12 (130)
1.57 (40)

45

(9

5)

5.0000
DIA 4.9975

0
(127-0.063
)

6.14 (156)

Flange
ISO 3019-1

3.68 (93.5)

0.50 (12.7)

L1

0.79 (20)

0.69 (17.5)
3.42 (87)

3.

74

7.13 (181)
8.26 (210)

9.65 (245)

View X1)

2.63
(66.7)

3.50 (88.9)
2.36 (60)

1.26 (32)

Detail Z

Port plate 62
2.63 (66.7)
1.26 (32)

max. 9.50 (241.5)


5.12 (130)
X

Flange
ISO 3019-1

1.25 (31.8)

View Y1)

B
1.25
(31.8)

(127

0
-0.063

2.36
(63)
3.50 (88.9)

L
5.0000
DIA 4.9975

1.77
(45)

1.57 (40)

0.50 (12.7)

2.00
(50.8)
1.97
(50)

S
0.79 (20)
9.27 (235.5)
10.90 (277)
1)

2.00
(50.8)

3.74 (95)

3.35 (85)

Dimensions of working ports turned through 180 for counter-clockwise rotation

RE-A 92703/03.2015, Bosch Rexroth AG

50

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 85

Dimensions, size 85
DR Hydraulic pressure controller; Clockwise rotation, mounting flange D series 53
Port plate 61
max. 9.90 (251.5)
5.63 (143)
1.42 (36)

L1
X

L
(4

3.

(9
3.

74

74

(9

5)

45

0
(127 -0.063
)

16

5.0000
DIA 4.9975

0.

5.91 (150)
4.96 (126)

Flange
ISO 3019-1

5)
0.
(1 5
4. 6
3) 4.51 (114.5)
4.04 (102.5) 3.98 (101)

0.50 (12.7)

16

0.

45

(4
)

L2

5.12 (130)
9.65 (245)

4.51 (114.5)
5.75 (146)

2.63
(66.7)

3.50 (88.9)
2.36 (60)

1.26 (32)

View X1)

S
2.00
(50.8)

5.63 (143)
0.50 (12.7)

1.42 (36)
X

Flange
ISO 3019-1

2.36
(63)
3.50 (88.9)

5.0000
4.9975
0
(127 -0.063
)
DIA

5.12 (130)
9.25 (235)
10.91 (277)

2.00
(50.8)

1.25
(31.8)

Dimensions of working ports turned through 180 for counter-clockwise rotation

Bosch Rexroth AG, RE-A 92703/03.2015

1.77
(45)

View Y1)

0.79 (20)

1)

Detail Z

1.25 (31.8)

max. 9.90 (251.5)

1.97
(50)

2.63 (66.7)
1.26 (32)

Port plate 62

3.74 (95)

3.35 (85)

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 51


Dimensions, size 85




Splined shaft 1 1/2 in SAE J744

Splined shaft 1 1/4 in SAE J744


U 14T 12/24DP1)

S 17T 12/24DP

2.12 (54)

5/16-18UNC-2B3) 4)

7/16-14UNC-2B

3) 4)

1)

1.10 (28)
0.20(5)

1.71
(43.5)

1.87 (47.5)
0.75 (19)
0.20 (5)

1.38
(35)

2.44 (61.9)

2.18 (55.4)

Splined shaft 1 1/4 in SAE J744

5/16-18UNC-2B3) 4)

W 14T 12/24DP1)

Usable
shaft length

0.75 (19)
0.20 (5)

1.30 (33)
2.18 (55.4)

Ports

Size4)

pmax abs
[psi (bar)]5)

State9)

Working port (high-pressure line)


Fastening thread

SAE J518
ASME B1.1

1 1/4 in
1/2-13UNC-2B; 0.75 (19) deep

4600 (315)

Suction port (standard pressure series)


Fastening thread

SAE J518
ASME B1.1

2 1/2 in
1/2-13UNC-2B; 1.07 (27) deep

75 (5)

Drain port

ISO 119266)

1 1/16-12UNF-2B; 0.59 (15) deep

30 (2)

O7)

L1, L2

Drain port

ISO 11926

1 1/16-12UNF-2B; 0.59 (15) deep

30 (2)

X7)

Control pressure

ISO 11926

7/16-20UNF-2A; 0.45 (11.5) deep

4600 (315)

L
8)

1)

2)

3)
4)

5)

Standard

6)

Involute spline according to ANSIB92.1a, 30 pressure angle, flat


root, side fit, tolerance class5
Splines according to ANSI B92.1a, run out of spline is a deviation
from standard.
Thread according to ASME B1.1
Observe the project planning notes on page 68 concerning the
maximum tightening torques.
Depending on the application, momentary pressure spikes can occur.
Keep this in mind when selecting measuring equipment and fittings

6)
7)

8)
9)

The spot face can be deeper than as specified in the standard.


Depending on the installation position, L, L1 or L2 must be connected (also see installation instructions starting on page 64).
Only series 53
O = Must be connected (plugged on delivery) X = Plugged
(in normal operation)

RE-A 92703/03.2015, Bosch Rexroth AG

52

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions, size 85

DRG Pressure controller, remote controlled, series 52

EP.D. / EK.D. Electro-proportional control, series 53

max. 9.51 (241.5)

X
6.14 (156)
5.49(139.5)

2.91 (74)

10.51 (267)
7.15 (181.5)

L1
L

6.14 (156)
5.49(139.5)

2.91 (74)

11.06 (281)
7.14 (181.5)

L1
L

X 2.91 (74) L
1
X

LA.D. Pressure, flow and power control, series 53

5.91 (149.9)
5.71(145)
5.25 (133.4)

1)

ED7. / ER7. Electro-prop. Pressure control, series 52

L1

L1
L

L2

ER7.: 191 mm when using a sandwich plate pressure reducing


valve

Bosch Rexroth AG, RE-A 92703/03.2015

2.17 (55)
0.76 (19.4)
6.14 (156)1)

X 2.91 (74)

7.15 (181.5)
X

L2

10.68 (271.4)

10.67 (271)

5.91 (150)
5.24 (133)

EP.ED. / EK.ED. Electro-prop. control, series 53

max. 9.51 (241.5)


6.75 (171.5)

L2

DRF/DRS Pressure and flow control, series 52

1.42
2.91 (36)
(74) L

5.91 (150)
5.59 (142)
5.24 (133)

6.75 (171.5)

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 53


Dimensions size 100




Dimensions size 100


DR Hydraulic pressure controller; Clockwise rotation, mounting flange C series 53
Port plate 61
max. 9.90 (251.5)
5.63 (143)
X

5.91 (150)

45

5)

(9

5)

5.0000
4.0075
0
(127-0.063 )

(4

3.

3.

DIA

74

74

(9

X
16

0.

45

(4
)

L2

5.12 (130)
9.65 (245)

0.69 (17.5)
4.03 (102.5) 3.98 (101)

L1

L1
16

Flange
ISO 3019-1

1.42 (36)

0.

0.50 (12.7)

7.13 (181)
8.27 (210)

3.50 (88.9)
2.36 (60)

1.26
2.62 (32)
(66.7)

View X1)

0.50 (12.7)
Flange
ISO 3019-1

1.42 (36)

L1

1.25
(31.8)

DIA5.0000
4.9975
0
(127-0.063
)

2.48
(63)
3.50 (88.9)

5.12 (130)
9.25 (235)
10.91 (277)

1)

2.00
(50.8)

1.25
(31.8)

View Y1)

0.79 (20)

1.97 1.77
(50) (45)

3.35 (95)

max. 9.90 (251.5)


5.63 (143)

Detail Z

2.63 (66.7)
1.26 (32)

Port plate 62

2.00
(50.8)

3.35 (85)

Dimensions of working ports turned through 180 for counter-clockwise rotation

RE-A 92703/03.2015, Bosch Rexroth AG

54

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions size 100

Dimensions size 100


DR Hydraulic pressure controller; Clockwise rotation, mounting flange D series 53
Port plate 61
max. 9.90 (251.5)
5.63 (143)

0.

L
5)

45

3.

3.

74

74

(9

5)

(9

(127 -0.063 )

5.0000
DIA 4.9975

(4

5.91 (150)
4.96 (126)

16

L1

Flange
ISO 3019-1

L1
X

4.51 (114.5)
4.03 (102.5) 3.98 (101)

1.42 (36)

0.50 (12.7)

45

9.65 (245)

4.51 (114.5)
5.75 (146)

0
(1 .5
4. 6
3)

L2

5.12 (130)

2.62
(66.7)

3.50 (88.9)
2.36 (60)

1.26 (32)

View X1)

2.63 (66.7)
1.26
(32)

Detail Z

5.63 (143)

L1

2.48
(63)
3.50 (88.9)

5.12 (130)
9.25 (235)
10.91 (277)
1)

2.00
(50.8)

Dimensions of working ports turned through 180 for counter-clockwise rotation

Bosch Rexroth AG, RE-A 92703/03.2015

1.25
(31.8)

1.25
(31.8)

0.79 (20)

1.77
(45)

View Y1)

DIA 5.0000
4.9975
0
(127 -0.063
)

Flange
ISO 3019-1

1.42 (36)

max. 9.90 (251.5)


0.50 (12.7)

1.97
(50)

Port plate 62

2.00
(50.8)

3.74 (95)

3.35 (85)

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 55


Dimensions size 100




Splined shaft 1 1/2 in SAE J744

Splined shaft 1 1/4 in SAE J744


U 14T 12/24DP1)

S 17T 12/24DP

2.12 (54)

5/16-18UNC-2B3) 4)

7/16-14UNC-2B

3) 4)

1)

1.10 (28)
0.20(5)

1.71
(43.5)

1.87 (47.5)
0.75 (19)
0.20 (5)

1.38
(35)

2.44 (61.9)

2.18 (55.4)

Splined shaft 1 1/4 in SAE J744

5/16-18UNC-2B3) 4)

W 14T 12/24DP1)

Usable
shaft length

0.75 (19)
0.20 (5)

1.30 (33)
2.18 (55.4)

Ports

Size4)

pmax abs
[psi (bar)]5)

Status9)

Working port (high-pressure line)


Fastening thread

SAE J518
ASME B1.1

1 1/4 in
1/2-13UNC-2B; 0.75 (19) deep

4600 (315)

Suction port (standard pressure series)


Fastening thread

SAE J518
ASME B1.1

2 1/2 in
1/2-13UNC-2B; 1.07 (27) deep

75 (5)

Drain port

ISO 119266)

1 1/16-12UNF-2B; 0.59 (15) deep

30 (2)

O7)

L1, L2

Drain port

ISO 11926

1 1/16-12UNF-2B; 0.59 (15) deep

30 (2)

X7)

Control pressure

ISO 11926

7/16-20UNF-2A; 0.45 (11.5) deep

4600 (315)

L
8)

1)

2)

3)
4)

5)

Standard

Involute spline according to ANSIB92.1a, 30 pressure angle, flat


root, side fit, tolerance class5
Splines according to ANSI B92.1a, run out of spline is a deviation
from standard.
Thread according to ASME B1.1
Observe the project planning notes on page 68 concerning the
maximum tightening torques.
Depending on the application, momentary pressure spikes can occur.
Keep this in mind when selecting measuring equipment and fittings

6)

6)
7)

8)
9)

The spot face can be deeper than as specified in the standard.


Depending on the installation position, L, L1 or L2 must be connected (also see installation instructions starting on page 64).
Only series 53
O = Must be connected (plugged on delivery) X = Plugged
(in normal operation)

RE-A 92703/03.2015, Bosch Rexroth AG

DRG Pressure controller, remote controlled, series 53

5.91 (150)
5.24 (133)

L1

10.51 (267)
7.15 (181.5)

L2

X 2.91 (74)
5.91 (150)
5.24 (133)

L1

X 2.91 (74) L
1
X

5.91 (149.9)
5.71(145)
5.25 (133.4)

7.15 (181.5)

ED7. / ER7. Electro-prop. pressure control, series 53

L1
X

L1
L

L2

ER7.: 191 mm when using a sandwich plate pressure reducing


valve

Bosch Rexroth AG, RE-A 92703/03.2015

L2

10.71 (272)

X 2.91 (74)

L2

11.06 (281)
7.14 (181.5)

L2

10.67 (271)

EP.ED. / EK.ED. Electro-prop. control, series 53

LA.D. Pressure, flow and power control, series 53

DRF/DRS Pressure and flow control, series 53

max. 9.90 (251.5)


7.15 (181.5)

1.42
2.91 (36)
(74) L

5.91 (150)
5.59 (142)
5.24 (133)

X 2.91 (74)

EP.D. / EK.D. Electro-proportional control, series 53

5.91 (150)
5.24 (133)

max. 9.90 (251.5)


7.15 (181.5)

1)

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions size 100

6.14 (156)1)

56

L2

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 57


Dimensions through drive




Dimensions through drive


Flange ISO 3019-1 (SAE)

Hub for splined shaft1)

Diameter

Diameter

Symbol2)

82-2 (A)

= Available

Availability over sizes

Code

18

28

45

60/63

72

85

100

5/8 in

9T 16/32DP

K01

3/4 in

11T 16/32DP

K52

= On request

82-2

Section A-B
A3

5)

A4

10

6.5

A1 (to mounting flange)

0.39
(10)

A2

Omitted for NG 28

0.39
(10)

A1 (to mounting flange)

A1

A2

A3

18

7.17
(182)

1.53
(39)

0.74
M10; 0.57
(18.8) (14.5) deep

M10; 0.63
(16) deep

28

8.03
(204)

1.54
(39.3)

0.74
M10; 0.63
(18.8) (16) deep

2.09
(53)

M10; 0.63
(16) deep

45

9.02
(229)

1.55
(39.4)

0.75
M10; 0.63
(18.9) (16) deep

10.03 0.37
(255) (9.5)

2.32
(59)

M10; 0.63
(16) deep

60
63

10.03 1.55
(255) (39.4)

0.75
M10; 0.63
(18.9) (16) deep

72

10.03 0.37
(255) (9.5)

2.32
(59)

M10; 0.63
(16) deep

72

10.03 1.55
(255) (39.4)

0.75
M10; 0.63
(18.9) (16) deep

85

11.89 0.53
(302) (13.4)

2.68
(68)

M10; 0.79
(20) deep

85

11.89 1.74
(302) (44.1)

0.93
M10; 0.79
(23.6) (20) deep

100

11.89 0.53
(302) (13.4)

2.68
(68)

M10; 0.79
(20) deep

100

11.89 1.74
(302) (44.1)

0.93
M10; 0.79
(23.6) (20) deep

K01
NG
(SAE J744 16-4 (A))

2)

9(

A4

Omitted for NG 28

1)

4.1

+0.050

06.

(82.55 +0.020)

+0.050

(82.55 +0.020)

3.2520
DIA3.2508

9 (1

A3
45

45

4.1

Omitted for NG 28

A2

3.2520
DIA3.2508

Omitted for NG 28

Section A-B

A1

A2

A3

A43)

18

7.17
(182)

0.37
(9.3)

1.70
(43.3)

M10; 0.57
(14.5)deep

28

8.03
(204)

0.39
(9.9)

1.85
(47)

45

9.02
(229)

0.42
(10.7)

60
63

According to ANSI B92.1a, 30 pressure angle, flat root, side fit,


tolerance class 5
Mounting drillings pattern viewed from through drive with control
at top

K52
NG
(SAE J744 19-4 (A-B))

3)

A43)

Thread according to DIN 13, observe the project planning notes on


page 68 for the maximum tightening torques.

RE-A 92703/03.2015, Bosch Rexroth AG

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions through drive

58

Flange ISO 3019-1 (SAE)

Hub for splined shaft1)

Diameter

Diameter

Symbol2)

101-2 (B)

= Available

Availability over sizes

Code

18

28

45

60/63

72

85

100

7/8 in

13T 16/32DP

K68

1 in

15T 16/32DP

K04

= On request

101-2

Section A-B

Section A-B
Omitted for NG 45

A3

5.7
(14 5
6)

5.7
(14 5
6)
A4

A4

Omitted for NG 28, 45

A2

0.39
(10)

A2

Omitted for NG 45

K68
(SAE J744 22-4 (B))

2)

NG

A1

A2

A3

A43)

28

8.03
(204)

1.66
0.70
(42.3) (17.8)

M12; 0.71
(18) deep

45

9.02
(229)

1.67
0.71
(42.4) (17.9)

60
63

0.39
(10)

A1 (to mounting flange)

A1 (to mounting flange)

1)

4.0020
DIA 4.0008
(101.6 +0.050
+0.020 )

A3

45

45

4.0020
DIA 4.0008
(101.6 +0.050
+0.020 )

Omitted for NG 28, 45

A1

A2

A3

A43)

45

9.02
(229)

1.88
(47.9)

0.74
(18.9)

M12; 0.71
(18) deep

M121.75;
18 deep

60
63

10.03 1.87
(255) (47.4)

0.72
(18.4)

M12; 0.71
(18) deep

10.03 1.67
0.71
(255) (42.4) (17.9)

M12; 0.71
(18) deep

72

10.03 1.87
(255) (47.4)

0.72
(18.4)

M12; 0.71
(18) deep

72

10.03 1.67
0.71
(255) (42.4) (17.9)

M12; 0.71
(18) deep

85

11.89 2.01
(302) (51.2)

0.87
(22.2)

M12; 0.79
(20) deep

85

11.89 1.83
0.87
(302) (46.5) (22)

M12; 0.79
(20) deep

100

11.89 2.01
(302) (51.2)

0.87
(22.2)

M12; 0.79
(20) deep

100

11.89 1.83
0.87
(302) (46.5) (22)

M12; 0.79
(20) deep

According to ANSI B92.1a, 30 pressure angle, flat root, side fit,


tolerance class 5
Mounting drillings pattern viewed from through drive with control
at top

Bosch Rexroth AG, RE-A 92703/03.2015

K04
NG
(SAE J744 25-4 (B-B))

3)

Thread according to DIN 13, observe the project planning notes on


page 68 for the maximum tightening torques.

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 59


Dimensions through drive




Flange ISO 3019-1 (SAE)

Hub for splined shaft1)

Diameter

Diameter

Symbol2)

127-4 (C)

1 1/4 in
1 1/2 in

= Available

Availability over sizes


18

28

Code

45

60/63

72

85

100

14T 12/24DP

K15

17T 12/24DP

K16

= On request

127-4

Section A-B
A3
A2

1)

2)

A4

4.51 (114.5)

0.51
(13)

NG

A1

A2

A3

A43)

60
63

10.03
(255)

0.31
(8)

2.32
(59)

72

10.03
(255)

0.31
(8)

2.32
(59)

85

11.87
0.51
(301.5) (13)

2.67
M12;
(67.9) through

100

11.87
0.51
(301.5) (13)

2.67
M12;
(67.9) through

+0.050

0.53
(13.4)

A1 (to mounting flange)

NG

A1

M12; 0.63
(16) deep

85

11.87
0.51
(301.5) (13)

2.67
M12;
(67.9) through

M12; 0.63
(16) deep

100

11.87
0.51
(301.5) (13)

2.67
M12;
(67.9) through

According to ANSI B92.1a, 30 pressure angle, flat root, side fit,


tolerance class 5
Mounting drillings pattern viewed from through drive with control
at top

K16
(SAE J744 32-4 (C))

5.0020
DIA 5.0008

A4

A1 (to mounting flange)

(127 +0.020 )

4.51 (114.5)

4.51 (114.5)
4.51 (114.5)

A3
A2

5.0020
DIA 5.0008
+0.050
(127 +0.020 )

K15
(SAE J744 32-4 (C))

Section A-B

3)

A2

A3

A43)

Thread according to DIN 13, observe the project planning notes on


page 68 for the maximum tightening torques.

RE-A 92703/03.2015, Bosch Rexroth AG

60

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Dimensions through drive

Flange ISO 3019-1 (SAE)

Hub for splined shaft1)

Diameter

Diameter

Symbol2)

127-2 (B)

= Available

Availability over sizes

Code

18

28

45

60/63

72

85

100

1 1/4 in

14T 12/24DP

K07

1 1/2 in

17T 12/24DP

K24

= On request

127-2

Section A-B

(127 +0.020 )

5.0020
DIA 5.0008

+0.050

A4
B

3
7.1 1)
8
1
(

A1 (to mounting flange)

K07
(SAE J744 32-4 (C))

1)

2)

NG

A1

A2

A3

A43)

85

11.87
0.51
(301.5) (13)

2.67
M12;
(67.9) through

100

11.87
0.51
(301.5) (13)

2.67
M12;
(67.9) through

According to ANSI B92.1a, 30 pressure angle, flat root, side fit,


tolerance class 5
Mounting drillings pattern viewed from through drive with control
at top

Bosch Rexroth AG, RE-A 92703/03.2015

+0.050

A4

0.51
(13)

A2

(127 +0.020 )

3
7.1 1)
8
1
(

A3
A2

45

A3

5.0020
DIA 5.0008

45

Section A-B

A1 (to mounting flange)

K24
NG
(SAE J744 38-4 (C-C))

3)

0.51
(13)

A1

A2

A3

A43)

85

11.89
(302)

0.31
(8)

2.68
(68)

M16; 0.94
(24) deep

100

11.89
(302)

0.31
(8)

2.68
(68)

M16; 0.94
(24) deep

Thread according to DIN 13, observe the project planning notes on


page 68 for the maximum tightening torques.

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 61


Overview of attachment options




Overview of attachment options


Through drive
Flange
ISO 3019-1

Hub for
splined
shaft

Short
des.

A10V(S)O/5x
NG (shaft)

A10VO/31
NG (shaft)

A1VO/10
NG (shaft)

External
gear pump

82-2 (A)

5/8 in

K01

10 (U), 18 (U)

18 (U)

18 (S2)

Series F

3/4 in

K52

10 (S), 18 (S, R)

18 (S, R)

18 (S3)

7/8 in

K68

28 (S,R)
45 (U, W)1)

28 (S,R)
45 (U,W)

35 (S4)

Series N/G

1 in

K04

45 (S,R)
60, 63 (U, W)2)
72 (U, W)2)

45 (S,R)

35 (S5)

1 1/4 in

K15

60, 63 (S, R)
72 (S,R)

1 1/2 in

K16

85 (S)
100 (S)

1 1/4 in

K07

85 (U,W)
100 (U, W)

71 (S,R)

PGH5

1 1/2 in

K24

85 (S)
100 (S)

101-2 (B)

127-4 (C)

127-2 (C)

1)
2)

Attachment options of 2nd pump

Not for NG28 with K68


Not for NG28 with K04

RE-A 92703/03.2015, Bosch Rexroth AG

62

Dimensions [in (mm)]

A10VO series 52 and 53 | Axial piston variable pump


Combination pumps A10VO + A10VO

Combination pumps A10VO + A10VO


Through the use of combination pumps, it is possible to
have independent circuits without the need to fit splitter
gearboxes.
When ordering combination pumps, the type designations
of the 1st and 2nd pump must be linked with a + sign.

m1

Order example:

m2

A10VO85DRS/53R-VSC12K04+
A10VO45DRF/53R-VSC11N00
It is permissible to use a combination of two single pumps

l1

of the same nominal size (tandem pump) considering a

l2

dynamic mass acceleration of maximum 10 g (= 98.1 m/s )


2

without additional support brackets.


For combination pumps consisting of more than two

m1, m2, m3

Weight of pump

pumps, the mounting flange must be rated for the permis-

l1, l2, l3

Distance, center of gravity

sible mass torque (please consult us).

Tm = (m1 l1 + m2 l2 + m3 l3)

[lbs (kg)]
1
12 (102)

[in (mm)]
[lb-ft (Nm)]

Permissible mass moment of inertia


NG

10

18

28

45

60/63

72

85

100

static

Tm

lb-ft
(Nm)

656
(890)

664
(900)

1010
(1370)

1010
(1370)

2270
(3080)

2270
(3080)

dynamic at 10g (98.1 m/s2)

Tm

lb-ft
(Nm)

65
(89)

66
(90)

101
(137)

101
(137)

227
(308)

227
(308)

Weight with through-drive plate


Weight without through-drive plate
(e.g. 2nd pump)

lbs (kg)

()
8 (18)

29 (13)
25 (11.5)

40 (18)
33 (15)

53 (24)
40 (18)

62 (28)
49 (22)

62 (28)
49 (22)

99 (45)
79 (36)

99 (45)
79 (36)

Distance, center of gravity


without through drive

l1

in
(mm)

3.07
(78)

3.35
(85)

3.78
(96)

4.13
(105)

4.13
(105)

4,80
(122)

4.80
(122)

Distance, center of gravity


with through drive

l1

in
(mm)

3.42
(87)

3.90
(99)

4.53
(115)

5.00
(127)

5.00
(127)

5.90
(150)

5.90
(150)

Bosch Rexroth AG, RE-A 92703/03.2015

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 63


Connector for solenoids




Connector for solenoids


DEUTSCH DT04-2P-EP04

1.44 (36.7)

Molded connector, 2-pin, without bidirectional suppressor

(2)

The following type of protection is provided with installed


mating connector:
IP67 (DIN/EN 60529) and

(1)

DIA 1.46
(37)

1.44 (36.7)

diode

IP69K (DIN 40050-9)

1.97 (50)

Circuit diagram symbol

2.70 (68.5)

Changing plug position


If necessary, you can change the position of the connector
by turning the solenoid.
To do this, proceed as follows:
Loosen the mounting nut (1) of the solenoid. To do this,
turn the mounting nut (1) one turn counter-clockwise.

Mating connector DEUTSCH DT06-2S-EP04


Consisting of

DT designation

1 case

DT06-2S-EP04

1 wedge

W2S

2 sockets

0462-201-16141

Turn the solenoid body (2) to the desired orientation.


Retighten the fixing nut.
Tightening torque: 3.7+0.75 lb-ft (5+1Nm).
(WAF 26, 12-sided DIN 3124)

The mating connector is not included in the delivery


contents.

On delivery, the position of the connector may differ from


that shown in the brochure or drawing.

This can be supplied by Bosch Rexroth on request (material


number R902601804).

Electronic controls

Control

Electronics function

electronics for example

Further information

Electric pressure control

Controlled power outlet

RA

analog

95230

RC 4-5/30

digital

95205 or
www.boschrexroth.com/mobile-lectronics

RE-A 92703/03.2015, Bosch Rexroth AG

64

A10VO series 52 and 53 | Axial piston variable pump


Installation instructions

Installation instructions
General

Installation position

The axial piston unit must be filled with hydraulic fluid and

See the following examples 1 to 12.

air bled during commissioning and operation. This must

Further installation positions are available upon request.

also be observed following a longer standstill as the axial

Recommended installation position: 1 and 3

piston unit may drain back to the reservoir via the hydraulic
lines.

Below-tank installation (standard)

Particularly with the drive shaft up/down installation

Below-tank installation means the axial piston unit is

position, filling and air bleeding must be carried out com-

installed outside of the reservoir below the minimum fluid

pletely as there is, for example, a danger of dry running.

level.

The case drain fluid in the pump housing must be directed to


the reservoir via the highest available drain port (L, L12), L23 )).
For combinations of multiple units, the case drain fluid

Installation position

Air bleeding

Filling

12)

S + L or L1

S + L1

S + L or L1

S + L or L1

must be drained off at each pump. If a shared reservoir line

ht min
h min

is used for this purpose, make sure that the case pressure
in each pump is not exceeded. In the event of pressure

L1

differences at the drain ports of the units, the shared drain

SB

line must be changed so that the minimum permissible


case pressure of all connected units is not exceeded in any

situation. If this is not possible, separate drain lines must


be laid if necessary.
To achieve favorable noise values, decouple all connecting

21)

lines using elastic elements and avoid above-reservoir

installation.

ht min
h min

In all operating conditions, the suction line and drain line


must flow into the reservoir below the minimum fluid level.

L1

The permissible suction height hS results from the overall


S

hSmax=31.50in (800mm). The minimum suction pressure


during operation and during cold start.

loss of pressure. However, it must not be higher than


at port S must also not fall below 12psi (0.8bar) absolute

SB

3 3)

When designing the reservoir, ensure adequate distance


between the suction line and the case drain line. This prevents the heated, return flow from being drawn directly back
into the suction line.

ht min
h min

SB

L2 S

Note
In certain installation positions, an influence on the control characteristics can be expected. Gravity, dead weight

L1 L

and case pressure can cause minor shifts in control characteristic curves and changes in response time.
For key, see page66.

F
ht min
h min

1)

2)

3)

Because complete air bleeding and filling are not possible in this
position, the pump should be air bled and filled in a horizontal position before installation.
For NG10 and NG28 series 52, L1 is opposite, L must then be connected if necessary.
Only series 53

Bosch Rexroth AG, RE-A 92703/03.2015

SB

S
L
L1

Dimensions [in (mm)]

Axial piston variable pump | A10VO series 52 and 53 65


Installation instructions




Above-reservoir installation

A check valve in the case drain line is only permissible in

Above-reservoir installation means the axial piston unit is

individual cases. Consult us for approval.

installed above the minimum fluid level of the reservoir. To


prevent the axial piston unit from draining in position 6, the
height difference hESmin must be at least 0.98in (25mm).

For key, see page66.

Observe the maximum permissible suction height


hSmax =31.50in (800 mm).
Installation position

Air bleeding

Filling

52)

L1 or L

L1

L2

S or L

F
L

L1

hs max

S
ht min
h min

SB

61)2)

hES min

L1
L

hs max
ht min
h min

SB

73)

L2

L1 L

S
hs max

ht min
h min

81)

SB

L1

L
hs max
ht min
h min

1)

2)

3)

SB

Because complete air bleeding and filling are not possible in this
position, the pump should be air bled and filled in a horizontal position before installation.
For NG10 and NG28 series 52, L1 is opposite, L must then be connected if necessary.
Only series 53
RE-A 92703/03.2015, Bosch Rexroth AG

A10VO series 52 and 53 | Axial piston variable pump


Installation instructions

66

Reservoir installation

Key and assembly note

Inside-reservoir installation is when the axial piston unit is


installed in the reservoir below the minimum fluid level. The
axial piston unit is completely below the hydraulic fluid.
If the minimum fluid level is equal to or below the upper
edge of the pump, see chapter Above-reservoir installation.
Axial piston units with electrical components (e.g., electric
control, sensors) may not be installed in a reservoir below
the fluid level.
Installation position

Air bleeding

Filling

92)

Via the highest


available port L

Automatically via
the open port L
or L1 due to the
position under
the hydraulic
fluid level

L1

L
h t min

SB

Suction port

L; L1

Reservoir port

SB

Baffle (baffle plate)

ht min

Minimum required immersion depth (7.87in (200 mm))

hmin

Minimum required distance to reservoir bottom(3.94in


(100 mm))

hES min

Minimum necessary height needed to protect the axial piston unit from draining (0.98in (25 mm)).

hS max

Maximum permissible suction height (21.50in (800mm))

Note
Filling / air bleeding
have to install the port F for a simpified filling and air
bleeding.

h min
10

h t min

L1
SB

Legend

The port F is a part of the external piping and the customer

Axial piston variable pump | A10VO series 52 and 53

Via the highest


Automatically via
available port L1 the open port L,
L1 or S due to the
position under
the hydraulic
fluid level

h min

113)

h t min

L2
L S

h min

SB

Via the highest


available port L

S SB

h t min

12

h min

L
L1

Automatically
via the open
port L, L1 or S
due to the position under the
hydraulic fluid
level

1)

2)

3)

Bosch Rexroth AG, RE-A 92703/03.2015

Because complete air bleeding and filling are not possible in this
position, the pump should be air bled and filled in a horizontal position before installation.
For NG10 and NG28 series 52, L1 is opposite, L must then be connected if necessary.
Only series 53




Axial piston variable pump | A10VO series 52 and 53 67

RE-A 92703/03.2015, Bosch Rexroth AG

68

A10VO series 52 and 53 | Axial piston variable pump


Project planning notes

Project planning notes

Safety instructions

The A10VO pump is designed to be used in open circuits.

During and shortly after operation, there is a risk of

Project planning, installation and commissioning of the

burns on the axial piston unit and especially on the

axial piston units requires the involvement of skilled

solenoids. Take appropriate safety measures (e.g., by

personnel.

wearing protective clothing).

Before using the axial piston unit, please read the core-

Moving parts in control equipment (e.g. valve spools)

sponding instruction manual thoroughly and completely.

can, under certain circumstances, get blocked in posi-

If necessary, request these from Bosch Rexroth.

tion as a result of contamination (e.g. impure hydraulic

Before finalizing your design, request a binding installation drawing.

fluid, abrasion, or residual dirt from components). As a


result, the flow of hydraulic fluid and the build-up of

The data and notes contained herein must be adhered to.

torque in the axial piston unit can no longer respond

Pressure controllers are not backups against pressure

correctly to the operator's specifications. Even the use

overload. A separate pressure relief valve is to be pro-

of various filter elements (external or internal flow

vided in the hydraulic system.

filtering) cannot rule out errors, but can only help mini-

Depending on the operating condition of the axial piston

mize risks. The machine/system manufacturer must test

unit (operating pressure, fluid temperature), the charac-

whether remedial measures are needed on the machine

teristic curve may shift.

for the application concerned in order to set the con-

Not all versions of the product are approved for use in a

sumer being driven to a safe position (e.g. safe stop)

safety function pursuant to ISO13849. Please consult

and if necessary to ensure it is properly implemented.

the responsible contact person at Bosch Rexroth if you


require reliability parameters (e.g. MTTFd) for functional
safety.
Working ports:
The ports and fastening threads are designed for the
specified peak pressure. The machine or system
manufacturer must ensure that the connecting elements and lines correspond to the specified operating conditions (pressure, flow, hydraulic fluid, temperature) with the necessary safety factors.
The service and function ports can only be used to
accommodate hydraulic lines.

Bosch Rexroth Corporation


Mobile Applications
8 Southchase Court
Fountain Inn, SC 29644-9018
USA
Telephone (864) 967-2777
Facsimile (864) 967-8900
www.boschrexroth-us.com

Bosch Rexroth Corporation


2315 City Line Road
Bethlehem, PA 18017-2131, USA
Telephone (610) 694-8300
Facsimile (610) 694-8467
www.boschrexroth-us.com

Bosch Rexroth AG, RE-A 92703/03.2015

Bosch Rexroth Corporation


All rights reserved. Neither this document, nor any part of it, may be reproduced, duplicated, circulated or disseminated, whether by copy, electronic
format or any other means, without the prior consent and authorization of
Bosch Rexroth Corp.
The data and illustrations in this brochure/data sheet are intended only to
describe or depict the products. No representation or warranty, either express
or implied, relating to merchantability or fitness for intended use, is given or
intended by virtue of the information contained in this brochure/data sheet.
The information contained in this brochure/data sheet in no way relieves the
user of its obligation to insure the proper use of the products for a specific
use or application. All products contained in this brochure/data sheet are
subject to normal wear and tear from usage.
Subject to change.

You might also like