FPAB20BH60B PFC SPM 3 Series For Single-Phase Boost PFC: Features General Description

FPAB20BH60B
PFC SPM 3 Series for Single-Phase Boost PFC

Features
General Description
The FPAB20BH60B is an advanced PFC SPM 3
module providing a fully-featured, high-performance
Boost PFC (Power Factor Correction) input power stage
for consumer, medical, and industrial applications.
These modules integrate optimized gate drive of
the built-in IGBT to minimize EMI and losses, while also
providing multiple on-module
protection
features
including under-voltage lockout, over-current shutdown,
thermal monitoring, and fault reporting. These modules
also feature a full-wave rectifier, and high-performance
output diode for additional space savings and mounting
convenience.
UL Certified No. E209204 (UL1557)

600 V - 20 A Single-Phase Boost PFC with Integral
Gate Driver and Protection
Very Low Thermal Resistance Using Al2O3 DBC
Substrate
Full-Wave Bridge Rectifier and High-Performance
Output Diode
Built-in NTC Thermistor for Temperature Monitoring
Optimized for 20kHz Switching Frequency
Isolation Rating: 2500 Vrms/min.
Applications
Single-Phase Boost PFC Converter
Related Source
AN-9090 - PFC SPM 3 Series Users Guide
AN-9091 - Boost PFC Inductor Design Guide
Figure 1. Package Overview
Package Marking & Ordering Information

Device
Device Marking
Package
Packing Type
Quantity
FPAB20BH60B
FPAB20BH60B
SPMIC-027
Rail
10
2010 Fairchild Semiconductor Corporation
FPAB20BH60B Rev. C4
www.fairchildsemi.com
FPAB20BH60B PFC SPM 3 Series for Single-Phase Boost PFC
December 2013
PFC converter for single-phase AC / DC power conversion (please refer to Figure 3)
Integrated Drive, Protection, and System Control Functions

For IGBTs: gate drive circuit, Over-Current Protection (OCP), control supply circuit Under-Voltage Lock-Out (UVLO) Protection
Fault signal: corresponding to OC and UV fault
Built-in thermistor: temperature monitoring
Input interface: active-HIGH interface, works with 3.3 / 5 V logic, Schmitt-trigger input
Pin Configuration
Top View
12.205
(21)P
18.345
(1)VCC
(2)COM
(3)COM
(4)COM
(5)IN
(6)VFO
(7)CFOD
(8)CSC
(22)P
(23)N.C
(9)RTH
(10)VTH
(24)L
(11)N.C
Case Temperature (TC)

Detecting Point
(12)N.C
(25)PR
(13)N
(14)N
(15)N
(16)N
(26)R
(17)NR
(18)NR
DBC Substrate
(19)NR
(27)S
(20)NR
Figure 2. Top View

Notes :
1. For the measurement point of case temperature(TC), please refer to Figure 2.
FPAB20BH60B Rev. C4
Integrated Power Functions
Pin Descriptions
Pin Number
Pin Name
Pin Description
VCC
Common Bias Voltage for IC and IGBT Driving
2,3,4
COM
Common Supply Ground
IN
VFO
CFOD
Capacitor for Fault Output Duration Selection
CSC
Capacitor (Low-Pass Filter) for Over-Current Detection
R(TH)
Series Resistor for The Use of Thermistor
10
V(TH)
Thermistor Bias Voltage
11,12
N.C
No Connection*
13~16
IGBT Emitter
17~20
NR
Negative DC-Link of Rectifier
21,22
23
N.C
24
25
PR
Positive DC-Link of Rectifier
26
AC Input for R-Phase
27
AC Input for S-Phase
Signal Input for IGBT

Fault Output
Positive Rail of DC-Link

No Connection
Reactor Connection Pin
* 11th and 12th pins are cut. Please refer to package outline drawings for more detail.
Internal Equivalent Circuit and Input/Output Pins

(10) VTH
NTC
Thermistor
(9) RTH
(8) CSC
CSC
(7) CFOD
CFOD
(6) VFO
VFO
(5) IN
IN
(21,22) P
(24) L
(25) PR
OUT
(26) R
(2~4) COM
COM
(1) VCC
VCC
(27) S
(13~16) N
(17~20) NR
Figure 3. Internal Block Diagram
FPAB20BH60B Rev. C4
unless otherwise specified.)
Converter Part
Symbol
Vi
Vi(Surge)
VPN
VPN(Surge)
VCES
Item
Condition
Rating
Unit
Supply Voltage
Applied between R - S
264
Vrms
Supply Voltage (Surge)
500
Output Voltage
Applied between P - N
450
Output Voltage (Surge)
500
600
Collector - Emitter Voltage
IC
Each IGBT Collector Current
TC = 25C, TJ < 150C
20
ICP
Each IGBT Collector Current (Peak)
TC = 25C, TJ < 150C, Under 1ms Pulse Width
40
PC
Collector Dissipation
TC = 25C
89
600
250
-40 ~ 150
VRRM
Repititive Peak Reverse Voltage
IFSM
Peak Forward Surge Current
TJ
Single Half Sine-Wave
Operating Junction Temperature
Control Part
Symbol
Item
Condition
Rating
Unit
20
VCC
Control Supply Voltage
Applied between VCC - COM
VIN
Input Signal Voltage
Applied between IN - COM
-0.3 ~ VCC+0.3
VFO
Fault Output Supply Voltage
Applied between VFO - COM
-0.3 ~ VCC+0.3
IFO
Fault Output Current
Sink Current at VFO Pin
mA
VSC
Current Sensing Input Voltage
Applied between CSC - COM
-0.3 ~ VCC+0.3
Rating
Unit
-40 ~ 125
2500
Vrms
Total System
Symbol
Item
TSTG
Storage Temperature
VISO
Isolation Voltage
Condition
60 Hz, Sinusoidal, AC 1 Minute, Connect Pins

to Heat Sink Plate
Thermal Resistance
Symbol
Min.
Typ.
Max.
Unit
IGBT
1.4
C/W
R(j-c)F
FRD
1.4
C/W
R(j-c)R
Rectifier (per 1 / 4 module)
2.1
C/W
R(j-c)Q
Item
Junction to Case Thermal Resistance
FPAB20BH60B Rev. C4
Condition
Absolute Maximum Ratings (TJ = 25C,
Converter Part
Symbol
VCE(SAT)
Item
Condition
Min.
Typ.
Max. Unit
IGBT Saturation Voltage
VCC = 15 V, VIN = 5 V, IC = 20 A
2.3
3.0
VFF
FRD Forward Voltage
IF = 20 A
1.8
2.5
VFR
Rectifier Forward Voltage
IF = 20 A
1.2
1.5
tON
Switching Times
VPN = 400 V, VCC = 15V, IC = 20 A

VIN = 0 V 5 V, Inductive Load
450
ns
200
ns
350
ns
tC(OFF)
80
ns
trr
70
ns
Irr
250
tC(ON)
(Note 2)
tOFF
ICES
Collector - Emitter
Leakage Current
VCE = VCES
Notes:
2. tON and tOFF include the propagation delay of the internal drive IC. tC(ON) and tC(OFF) are the switching time of IGBT itself under the given gate driving condition internally. For
the detailed information, please see Figure 4.
Irr
120% of IC
100% of IC
VCE
IC
90% of IC
15% of VCE
IC
10% of IC
VCE 15% of VCE
10% of IC
VIN
VIN
tON
trr
tC(OFF)
tC(ON)
tOFF
(a) Turn-on
(b) Turn-off
Figure 4. Switching Time Definition
FPAB20BH60B Rev. C4
Electrical Characteristics (TJ = 25C, unless otherwise specified.)
Symbol
Item
Condition
IQCCL
Quiescent VCC Supply Current
VCC = 15 V, IN = 0 V VCC - COM
VFOH
Fault Output Voltage
VFOL
Min. Typ. Max. Unit

-
26
mA
VSC = 0 V, VFO Circuit: 4.7 k to 5 V Pull-up
4.5
VSC = 1 V, VFO Circuit: 4.7 k to 5 V Pull-up
0.8
VSC(ref)
Over-Current Trip Level
VCC = 15 V
0.45
0.5
0.55
UVCCD
Supply Circuit Under-Voltage

Protection
Detection Level
10.7
11.9
13.0
Reset Level
11.2
12.4
13.2
tFOD
Fault-Out Pulse Width
CFOD = 33 nF (Note 3)
1.4
1.8
2.0
ms
VIN(ON)
ON Threshold Voltage
Applied between IN - COM
2.8
VIN(OFF)
OFF Threshold Voltage
0.8
@ TTH = 25C (Note 4, Figure 5)
47.0
@ TTH = 100C (Note 4, Figure 5)
2.9
UVCCR
RTH
Resistance of Thermistor
Notes:
3. The fault-out pulse width tFOD depends on the capacitance value of CFOD according to the following approximate equation: CFOD = 18.3 x 10-6 x tFOD [F].
4. TTH is the temperature of know case temperature(TC), please make the experiment considering your application.
R-T Curve
200
MIN
TYP
MAX
4
MIN
TYP
MAX
Resistance RTH[k]
Resistance RTH[k]
150
100
1
95
100
105
110
115
120
125
Temperature TTH[]
50
0
0
25
50
75
100
125
Temperature TTH[]
Figure 5. R-T Curve of the Built-In Thermistor
FPAB20BH60B Rev. C4
Control Part
Symbol
Item
Condition
Min. Typ. Max.
Unit
Input Supply Voltage
187
220
253
Vrms
VPN
Output Voltage
380
400
VCC
Control Supply Voltage
Applied between VCC(L) - COM
13.5
15.0
16.5
dVCC/dt
Control Supply Variation
-1
V/s
Vi
fPWM
PWM Input Frequency
TJ 150C
20
kHz
Ii
Allowable Input Current
TC < 90C, Vi = 220 V, VPN = 380 V

VPWM = 20 kHz
20
Apeak
Min.
Typ.
Max.
Unit
0.51
0.62
0.72
Nm
+120
15.00
Mechanical Characteristics and Ratings

Item
Condition
Mounting Torque
Mounting Screw: M3
Device Flatness
See Figure 6
Recommended 0.62 Nm
Weight
(+)
(+)
(+)
Figure 6. Flatness Measurement Position
FPAB20BH60B Rev. C4
Recommended Operating Condition
Time Charts of Protective Function

Input S ignal
Internal IG B T
G ate-E m itter V oltage
P3
UV
reset
P5
C ontrol S upply V oltage
P2
UV
detect
P6
P1
O utput C urrent
P4
Fault O utput S ignal

P1 : Normal operation: IGBT ON and conducting current
P2 : Under-voltage detection
P3 : IGBT gate interrupt
P4 : Fault signal generation
P5 : Under-voltage reset
Figure 7. Under-Voltage Protection

P5
In p u t S ig n a l
P6
In te r n a l IG B T
G a te - E m itte r V o lta g e
O C D e te c tio n
P1
P4
P7
O u tp u t C u r r e n t
P2
O C R e fe r e n c e
V o lta g e ( 0 .5 V )
S e n s in g V o lta g e
R C F ilte r D e la y
F a u lt O u tp u t S ig n a l
P3
P8

P2 : Over current detection
P3 : IGBT gate interrupt / fault signal generation
P4 : IGBT is slowly turned off
P5 : IGBT OFF signal
P6 : IGBT ON signa: but IGBT cannot be turned on during the fault output activation
P7 : IGBT OFF state
P8 : Fault output reset and normal operation start
Figure 8. Over-Current Protection
FPAB20BH60B Rev. C4
VTH
NTC
Thermistor
RTH
+5 V
CSC
CFOD
VFO
PFC
Controller
P
L
CSC
CFOD
PR
VFO
OUT
IN
IN
COM
+15 V
VCC
VAC
COM
VCC
N
NR
Fig. 9. Application Example

Notes:
5. Each capacitors should be located as close to PFC SPM product pins as possible.
6. Its recommended that anti-parallel diode should be connected with IGBT.
FPAB20BH60B Rev. C4
+5 V
Detailed Package Outline Drawings
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or data on the drawing and contact a FairchildSemiconductor representative to verify or
obtain the most recent revision. Package specifications do not expand the terms of Fairchilds worldwide therm and conditions,
specifically the the warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductors online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/dwg/MO/MOD27BE.pdf
FPAB20BH60B Rev. C4
10
FPAB20BH60B Rev. C4
11

FPAB20BH60B PFC SPM 3 Series For Single-Phase Boost PFC: Features General Description

Uploaded by

Copyright:

Available Formats

FPAB20BH60B PFC SPM 3 Series For Single-Phase Boost PFC: Features General Description

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FPAB20BH60B PFC SPM 3 Series For Single-Phase Boost PFC: Features General Description

Uploaded by

Copyright:

Available Formats

FPAB20BH60B

PFC SPM 3 Series for Single-Phase Boost PFC

UL Certified No. E209204 (UL1557)

Figure 1. Package Overview

Package Marking & Ordering Information

2010 Fairchild Semiconductor Corporation