Jawaharlal Nehru Engineering

College

Laboratory Manual

Network Analysis

For
Second Year Students

JNEC, Aurangabad

FOREWORD
It is my great pleasure to present this laboratory manual for second
year engineering students for the subject of Network Analysis,
keeping in view the vast coverage required to visualize the basic
concepts of various networks using basic components.
NT covers designing
requirements.

network

for

specific

input/output

This being a core subject, it becomes very essential to have clear

theoretical and practical designing aspects.
This lab manual provides a platform to the students for
understanding the basic concepts of network theory. This practical
background will help students to gain confidence in qualitative and
quantitative approach to electronic networks.
Good Luck for your Enjoyable Laboratory Sessions.

LABORATORY MANUAL CONTENTS

This manual is intended for the second year students of engineering

branches in the subject of network theory. This manual typically
contains practical/Lab Sessions related to Network Theory covering
various aspects related the subject to enhance understanding.
In this manual we have made the efforts to cover various experiments
on network theory with detailed circuit diagrams, detailed procedure
and graphs wherever required.
Students are advised to thoroughly go through this manual rather
than only topics mentioned in the syllabus as practical aspects are
the key to understanding and conceptual visualization of theoretical
aspects covered in the books.
Good Luck for your Enjoyable Laboratory Sessions

Author

SUBJECT INDEX

1. Dos and Donts

2. Lab exercise:
1. Verification of Superposition Theorem.
2. Verification of Thevenins Theorem.
3. Verification of Nortons theorem.
4. Verification of Maximum power transfer theorem.
5. To plot frequency response of a series resonant circuit.
6. To plot frequency response of a parallel resonant circuit.
7. To measure input impedance and output impedance of a given two port
network.
8. To design a attenuator which attenuate given signal to the desired
level.
3. Quiz on the subject.
4. Conduction of Viva-Voce Examination.
5. Evaluation and Marking Systems.

Dos and Donts in Laboratory:

1. Do not handle any equipment before reading the instructions/Instruction manuals.
2. Apply proper voltage to the circuit as given in procedure.
3. Check CRO probe before connecting it.
4. Strictly observe the instructions given by the teacher/Lab Instructor.

Instruction for Laboratory Teachers:

1. Submission related to whatever lab work has been completed should be done during
the next lab session.
2. The promptness of submission should be encouraged by way of marking and
evaluation patterns that will benefit the sincere students.

EXPERIMENT.NO. 1

AIM: - To verify Superposition theorem.

APPARATUS: - Breadboard, Resistors, Milliammeter, connecting wires, etc.
CIRCUIT DIAGRAM:-

R
1

R
2
I2

I1
R3

V1

I3

V2
5 VOLTS

10 VOLTS

1l
THEORY:

2l

- If network contains two or more than two sources, then

principle of superposition theorem is used to simplify network
calculations. It may be stated as follows.
In a bilateral network if two or more than two energy sources are
present, then the current which flows at any point is the vector sum of
all currents which would flow at that point if each source was
considered separately and all other sources replaced at the time by
impedance equal to their internal impedances.

PROCEDURE:1. Connect D. C. power supply across terminals 1-1l and apply voltage of
say V1=10 volts and similarly across terminals 2-2l apply voltage of
say V2=15 volts
2. Measure current flowing through all branches, say these currents are
I1, I2, and I3.
3. Now connect only V1=10 volts across terminals1-1l and short circuit
terminals 2-2l that is V2=0 volts.
4. Measure currents flowing through all branches for V1=10 volts V2=0
volts using a milliameter, say these currents are I 1, I2, I3.
5. Similarly connect only V2 =15 volts across terminals 2-2l and short
circuit terminals 1-1l that is V1=0 volts.
6. Measure current flowing through all branches for V1=0 volts and V2=15
volts using a milliameter, say these currents are I1, I2, I3.
7. For verifying superposition theorem I 1= I1+ I1, I2= I2+ I2, I3=I3+I3.
8. Calculate theoretical values of currents, these values should be
approximately equal to measured values of currents.

OBSERVATION TABLE:-

V1=10VOLTS
V2=0VOLTS
I1=

V1=0VOLTS
V2=5 VOLTS
I1=

V1=10VOLTS
V2=5VOLTS
I1=

I2=

I2=

I2=

I3=

I3=

I3=

R1

R2

1
I2

I1
R3

V1

V2

I3

10V
VOLTS

15V
VOLTS

R1

R2

1
I2

I1
R3

V1

10V
VOLTS
1

V2

I3

15V
VOLTS
2

CONCLUSION: - The branch current is the algebraic sum of currents due to individual
voltage source when all other voltage sources are short circuited; hence superposition
theorem has been verified.

EXPERIMENT. NO. 2
AIM: - To verify Thevenins theorem.
APPARATUS: - Bread board, resistors, D.C. power supply, multimeter, connecting
wires, etc.
CIRCUIT DIAGRAM:-

R1

R2

RL

R3

2
l
l

THEORY:The current flowing through the load impedance R L connected across the terminals
2 & 2l of a network containing impedance & energy sources is the same as it would
flow if this load impedance were connected across a simple constant voltage source
whose generated emf is an open circuited voltage, measured across the network
terminals 2 & 2l. Its internal impedance is the same as the impedance of the network
looking back into the terminals 2 & 2l , when all sources have been replaced by
impedances and sources with output terminals 2 & 2 l. across which load impedance RL
is connected.
PROCEDURE:1. Apply dc voltage across terminals 1-1l, call this voltage as Vdc.
2. Connect voltmeter across terminals 2-2l and measure voltage on voltmeter. This
voltage is known as open circuit voltage or Thevenins voltage (Vth).
3. Vary the dc voltage across terminals 1-1l and repeat step 2, take two/three
readings.
4. Disconnect the applied voltage at terminals 1-1l and voltmeter at terminals 2-2l .
5. Now short terminals 1-1l and connect multimeter across terminals 2-2l . With
the help of multimeter measure resistance between terminals 2-2l . This is
known as Thevenins resistance (Rth).
6. Calculate Vth and Rth by theoretical calculations, the theoretical values and
measured values of Vth and Rth should be approximately equal.
7. Connect load resistor RL across terminals 2-2l and measure IL for applied dc
voltage.

OBSERVATION TABLE:-

Sr.No.

Vdc

Theoretical values
Rth
Vth
IL

Rth

Measured values
Vth
IL

CONCLUSION: - The theoretical values and measured values of Vth and Rth and IL are
approximately equal, hence Thevenins theorem has been verified.

EXPERIMENT NO. 3
AIM: - To verify Nortons theorem.
APPARATUS: - Breadboard, milliammeter (0-50mA), D.C. power supply (0-30V),
multimeter, resistors, connecting wires, etc.
CIRCUIT DIAGRAM:-

R1

R2

RL

R3

THEORY:Any two terminal linear network, consisting of generators and impedances, can be
replaced with an equivalent circuit consisting of a current source Isc in parallel
with an admittance YAB . The Isc is short circuit current between the network and
YAB is the admittance measured between the terminals, with all energy sources
eliminated except their internal impedances.
PROCEDURE:1. Apply d. c. voltage across terminals 1-1l called this voltage Vdc.
2. Connect milliammeter across terminals 2-2l and measure current, this is the
short circuit (Isc) current.
3. Vary the d. c. voltage across terminals 1-1l and repeat step 2, take three
readings.
4. Disconnect the applied voltage at terminals 1-1l and milliammeter at terminals
2-2l .
5. Short terminals 1-1l and connect Multimeter (keep it on resistance range)
across terminals 2-2l , and note down the reading , this resistance is known as
Req.
6. Calculate Isc and Req by using formulae, the calculated values and measured
values of Isc and Rth should be approximately equal.
7. Connect RL across terminals 2-2l and measure IL by milliammeter for applied
D.C. voltage.

10

OBSERVATION TABLE:Sr.No.
Vdc

Theoretical values
Rth
Vth
IL

Rth

Measured values
Vth
IL

CONCLUSION: - The Calculated values and measured values of Isc, IL, Req are
approximately equal; hence Nortons theorem has been verified.

11

EXPERIMENT. NO. 4
AIM: - To verify maximum power transfer theorem.
APPARATUS: - Breadboard, resistance, potentiometer, milliammeter, multimeter,
etc.
CIRCUIT DIAGRAM:1

R1

R2

2
+

mA __
+

Vdc

R3

RL

1l
lll
l

2l

THEORY:Maximum power will be delivered by a network to an impedance Z R if the

impedance of ZR is the conjugate of the impedance Z l
of the network,
measured looking back into the terminals of the network.
Zl

ZL

PROCEDURE:1. Make the connections according to circuit diagram.

1. Connect d.c. power supply of say Vdc=20 volts across terminal
1-1l .
2. Connect variable load RL across terminals 2-2l .
3. Vary RL gradually from minimum value and measure corresponding load current
IL .
4. Find load power for each value of RL and IL.
5. Draw the graph of power v/s load resistances.
6. From the graph note peak power point and correspondingly load resistance.
Verify the same using calculations.
7. Remove the d.c.power supply and short circuit the terminals 1-1l. Remove load
resistance connected across terminals 2-2l and measure the resistance with
the help of Multimeter. This resistance is approximately equal to the load
resistance found in step 6.

12

OBSERVATION TABLE:Sr.No.
Load resistance =
RL=VL/IL

Load voltage VL

Load current IL

Power = VL . IL

CONCLUSION: - The maximum power transfer takes place from the network to the
load when equivalent resistance of the network between terminals 2-2l is equal to the
load resistance.

IL

RL
MAX POWER

RL

13

EXPERIMENT NO 5.
AIM: To plot frequency response of series resonance circuit.
APPARATUS: Breadboard, Resistance, Inductance, capacitor, function generator,
millimeter (A.C), connecting wires etc.
CIRCUIT DIAGRAM:

Vs

Fun
Gen

MA

THEORY:In series RLC circuit

Impedance Z =

R2 + (XL Xc) 2

Current I = V/Z
And,
Phase angle = tan-1 (XL-Xc)/R
If the frequency of the signal fed to such a series circuit is increased from
minimum , the inductive reactance (XL= 2fl) increases linearly and the capacitive
reactance (Xc= 1/2fc) decreases exponentially.
At resonant frequency fr ,
- Net reactance , X=0 (i.e., XL=Xc)
- Impedance of the circuit is minimum , purely resistive and is equal to R
- Current I through the circuit is maximum and equal to V/R
- Circuit current , I is in phase with the applied voltage V (i.e. phase angle = 0).
At this particular resonant frequency a circuit is in series resonance.
Resonance occurs at that frequency when,
XL=Xc or 2fL = 1/2fc
Therefore fr = 1/2LC

14

BW of series RLC circuit : For frequency above and below resonant frequency
fr, f1 and f2 are frequencies at which the circuit current is 0.707 times the
maximum current , Imax or the 3dB points.
current

Io
W f2 f1

Io/

f1

fo

f2

Freq

Therefore from above figs

Bandwidth = f = f2-f1 Hz .
And quality factor Q = fr/f = fr/f2-f1

PROCEDURE:
1. Connect function generator and milliammeter as shown in circuit diagram.
2. Set the function generator output voltage to say Vs=10 Volts.
3. Increase the function generator output signal frequency from minimum say 10 Hz
to a maximum signal frequency of 100KHz in decade
steps(10,20,30..100,200,..1000,2000..10k,20k.100kHz).
4. For applied signal frequency measure current with the help of milliammeter.
5. Calculate theoretical frequency using fr =1/2LC
6. Plot the graph of frequency v/s current, find the frequency on the graph at which
current is maximum, this frequency is known as Resonant frequency and this should
be approximately to the theoretical frequency calculated in step 5.

15

OBSERVATION TABLE:
SR.NO

Frequency

Current (mA)

10Hz
20Hz
1KHz
100kHz

CONCLUSION: At resonance the current is maximum because the circuit impedance is

minimum and is equal to the value of resistance.

16

EXPERIMENT NO.6
AIM:-To plot frequency response of parallel resonant circuit.
APPARATUS:-Bread board, resistor, capacitor, inductor, function generator, LED.
milliammeter, connecting wires etc.
CIRCUIT DIAGRAM:-

Ic

R
I

0.1

90

Ic

IL

L1
1uH

Vs
90

mA
0-30mA

IL

THEORY:The circuit having an inductor & capacitor connected in parallel is called parallel
resonant circuit
If Xc < XL, then Ic >IL & the circuit acts capacitively .
If XL < Xc , then IL >Ic & the circuit acts inductively.
If XL = Xc, then IL =Ic & hence the circuit acts as a pure resistor .
In
1.
2.
3.

parallel resonant circuit at resonance condition

Phase difference between the circuit current and the applied voltage is zero
Maximum impedance
Minimum line current .

As in series resonance , all resonance circuit have the property of discriminating

between the frequency at resonance frequency (fr) and these not at resonance .
this property of the resonant circuit is expressed in terms of its bandwidth (BW)

17

PROCEDURE:1. Make the connections on breadboard according to circuit diagram.

2. Knowing the values of L and C calculate and record the resonance frequency of
parallel resonance circuit.
3. Set the output of function generator to 4 Vrms and frequency to 1khz .Record
the current I through the circuit
4. Increase the frequency gradually and record the resonance frequency Fr at
which the circuit current becomes minimum (that is LED does not glows or
glows very dimly.)
(This is the resonance frequency of the parallel resonance circuit because at
parallel resonance , current I through parallel LC circuit will be minimum)
5. Compare & record the difference in the resonance frequency calculated at step
2 & that measured in step4
6. Vary the input frequency in steps of 500 Hz around the resonance frequency &
in each step record the value of circuit current.
7. From the recorded readings of current in step 6 plot a graph of frequency
versus current & mark the resonance frequency.
8. Mark the -3 dB points on the plotted graph. Find bandwidth (B W) & quality
factor Q

OBSERVATION TABLE:
SR.NO

Frequency

Current (mA)

10Hz
20Hz
1KHz
100kHz

18

CONCLUSION:- At resonance the current is minimum because the circuit impedance

is maximum.

Fr

19

EXPERIMENT NO.7
AIM :- To measure input impedance and output impedance of a given two port network
APPARATUS :- Breadboard , resistance , multimeter , connecting wires, etc.
CIRCUIT DIAGRAM:R1

R2

I1

+
_

V1=5V

R3

V2=5V

R4

THEORY:In two port network port variables are port currents and port voltages. To describe
relationship between ports voltages and currents , two linear equations are
required. In the two port network , there are four variables . These are the
voltages and currents at the input and output ports , namely V1 , I1 and V2 , I2.
From this two are independent and two are dependent variables.
By expressing V1 and V2 in terms of I1 and I2
V1=Z11.I1+ Z22.I2
V2=Z21.I2+Z22.I2
From these equations we can find out all Z parameters.
PROCEDURE :1. Connect dc power supply Va =5V at port 1-1 and keep output port open
circuited i.e. I2=0.
2. Measure the current I1 by connecting milliammeter in series with R1.
3. Measure voltage V2 across R4 by Multimeter.
4. From these values of V1, V2, I1 and I2 (I2=0) find input driving point
impedance where V1=Va.
i.e. Z11 = V1/I1
I2=0
& Find forward transfer impedance
i.e.
Z21 = V2/I1
I2=0

20

5. Connect dc power supply Vb= 5v at port 2-2 and keep input port open circuited
i.e. I1=0.
6. Measure the current I2 by connecting milliammeter in series with supply .
7. Measure the voltage V1 across R3 by multimeter .
8. From this value of V2 , V1 , I2 and I1( I1=0) find output driving point impedance
that is
Z22 = V2/I2
I1=0
&

Z12 = V1/I2
I1=0

9. Calculate z-parameters theoretically. These values should be approximately equal

to the practical values of z-parameters.

OBSERVATION TABLE:
I2=0
Theoretical values

I1=0
Measured values

Theoretical values

V1=

V1=

V2=

V 2=

I1=

I2=

Z11=

Z12=

Z21=

Z22=

Measured values

CONCLUSION:-Since Z12=Z21 the circuit is reciprocal and since Z11 = Z22 the circuit
is not symmetrical.

21

EXPERIMENT NO.8
Aim: To design an attenuator which attenuate given signal to the desired level.
Equipment: Signal generator(0-1MHz),CRO(0-20MHz),Resistors.
Circuit Diagram:

R1
1

R2

Vs

R2

RL

Theory:
1. What is mean by attenuator?
2. Which are the different types of attenuator?
3. Symmetrical T and attenuator.

Design: RL=600 , D=10dB

R1=R0(N2-1)/2N) ,
R2=R0/2[(N+1)/ (N-1)],
N=antilog (Ddb/20)

R1=853.06
R2=577.78
2R2=1155.5

Procedure:
1. Connect the circuit as per circuit diagram.
2. Set input voltage VI=10V using signal generator and vary the frequency from (01MHz) in regular steps.
3. Note down the corresponding output voltage.
4. Plot the graph: output voltage Vs frequencies.

22

Observations:
SR.NO

Frequency

Current (mA)

10Hz
20Hz
1KHz
100kHz

Graph:

Result:
Attenuation:
Theoretical=

Practical=

Conclusion:

23

Questions for Quiz on NA.

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.

State the function of resistor, capacitor and inductor in a circuit?

What are the Kirchhoffs laws?
What is mesh analysis or loop analysis?
What is node or junction analysis?
What is mean by network and what are different types of networks?
Explain the term magnetic coupling?
State the meaning of resonance in LC circuit?
What is the impedance of series LC circuit?
State the condition for resonance in a series LC circuit?
What are the characteristics of series LC circuit at resonance?
Explain the relationship between the Q factor and bandwidth?
What are the different characteristics of LC parallel circuit at resonance?
List a few applications of series and parallel LC circuit?
What is mean by attenuator? What are the basic requirements of
attenuator?
What are the different types of symmetrical and asymmetrical attenuator?
What is minimum loss attenuator?
What is balanced and unbalanced attenuator? Where balanced attenuator is
required?
What is mean by equalizers? What are the types of equalizers?
What is inverse impedance?
What are the different parameters of linear time invariant two port network?
What is linear graph?
What are the properties of trees?
What is incidence matrix, cutset matrix and tieset matrix?
What are the Laplace transform and sin (t) and cos (t) ?
What is gate function, draw it?
State the basic principle of superposition theorem?
What are the steps to convert any network into its thevenins equivalent?
Convert the following network into Nortons equivalent circuit?
What is maximum power transfer theorem?
When a linear network is said to be reciprocal or bilateral?

24

4. Conduction of Viva-Voce Examinations:

Teacher should conduct oral exams of the students with full preparation. Normally, the
objective questions with guess are to be avoided. To make it meaningful, the questions
should be such that depth of the students in the subject is tested. Oral examinations
are to be conducted in cordial environment amongst the teachers taking the
examination. Teachers taking such examinations should not have ill thoughts about
each other and courtesies should be offered to each other in case of difference of
opinion, which should be critically suppressed in front of the students.

5. Evaluation and marking system:

Basic honesty in the evaluation and marking system is absolutely essential and in the
process impartial nature of the evaluator is required in the examination system to
become. It is a wrong approach or concept to award the students by way of easy
marking to get cheap popularity among the students, which they do not deserve. It is a
primary responsibility of the teacher to see that right students who are really putting
up lot of hard work with right kind of intelligence are correctly awarded.
The marking patterns should be justifiable to the students without any ambiguity and
teacher should see that students are faced with just circumstances.

25