Caged Ball LM Guide
Global Standard Type LM Guide Model SHS
2607993
LM rail
LM block
Endplate
End seal
45
45
Ball
Ball cage
Cross section
Fig. 1 Structure of Model SHS
Structure and Features
Balls roll in four rows of raceways precision-ground on an LM rail and an LM block, and ball
cages and endplates incorporated in the LM block allow the balls to circulate.
Each row of balls is placed at a contact angle of 45so that the rated loads applied to the LM
block are uniform in the four directions (radial, reverse-radial and lateral directions), enabling
the LM Guide to be used in all orientations. In addition, the LM block can receive a well-balanced preload, increasing the rigidity in the four directions while maintaining a constant, low
friction coefficient. With the low sectional height and the high rigidity design of the LM block,
SHS achieves highly accurate and stable linear motion.
4-way equal load
Each row of balls is placed at a contact angle of 45so that the rated loads applied to the LM
block are uniform in the four directions (radial, reverse-radial and lateral directions), enabling
the LM Guide to be used in all orientations and in extensive applications.
Self-adjustment capability
The self-adjustment capability through front-to-front configuration of
's unique circular-
arc grooves (DF set) enables a mounting error to be absorbed even under a preload, thus to
achieve highly accurate, smooth linear motion.
Global standard size
SHS is designed to have dimensions almost the same as that of model HSR, which
as
a pioneer of the linear motion system has developed and is practically a global standard model.
Low gravity center, high rigidity
As a result of downsizing the LM rail section, the center of gravity is lowered and the rigidity is increased.
a-134
a. Dimensions of the LM Guides
Model SHS-C
Model SHS-V
The flange of the LM block has tapped
The LM block has a smaller width (W) and
holes.
is equipped with tapped holes.
Can be mounted from the top or the bottom.
Suitable for places where space for the
Used in places where the table cannot
table width is limited.
have through holes for mounting bolts.
Model SHS-R
The LM block has a smaller width (W) and
the mounting holes are tapped.
It succeeds the height dimension of full-ball
type LM Guide HSR-R.
a-135
135 Global Standard Type LM Guide Model SHS
Types and Features
Model SHS-LC
Model SHS-LV
The LM block has the same sectional shape
The LM block has the same sectional
as model SHS-C, but has a longer overall LM
shape as model SHS-V, but has a longer
block length (L) and a greater rated load.
L
overall LM block length (L) and a greater
rated load.
L
Model SHS-LR
The LM block has the same sectional
shape as model SHS-R, but has a longer
overall LM block length (L) and a greater
rated load.
L
a-136
a. Dimensions of the LM Guides
Model SHS is capable of receiving loads in all
four directions: radial, reverse-radial and latPR
PL
eral directions.
The basic load ratings are uniform in the four
directions (radial, reverse-radial and lateral
directions), and their actual values are pro-
PT
PT
vided in the dimensional table for SHS.
Fig. 2
Equivalent Load
When the LM block of model SHS receives loads in all directions simultaneously, the equivalent
load is obtained from the equation below.
PEPR (PL)PT
where
PE
Equivalent load
(N)
Radial direction
Reverse-radial direction
Lateral direction
PR
Radial load
PL
Reverse-radial load
(N)
PT
Lateral load
(N)
(N)
a-137
137 Global Standard Type LM Guide Model SHS
Rated Loads in All Directions
Options
Dust Prevention Accessories
offers various dust prevention accessories for model SHS.
When a dust prevention accessory is required, specify the desired item with the corresponding
symbol provided in table 1 (for details of dust prevention accessories, see pages a-24 and a25).
For supported model numbers for dust prevention accessories and overall LM block length with
dust prevention accessories attached (dimension L), see page a-150.
Table 1 Symbols of Dust Prevention Accessories for Model SHS
Symbol
Dust prevention accessory
UU
With end seal
SS
With end seal + side seal + inner seal
DD
With double seals + side seal + inner seal
ZZ
With end seal + side seal + inner seal + metal scraper
KK
With double seals + side seal + inner seal + metal scraper
SSHH
With end seal + side seal + inner seal + LaCS
DDHH
With double seals + side seal + inner seal + LaCS
ZZHH
With end seal + side seal + inner seal + metal scraper + LaCS
KKHH
With double seals + side seal + inner seal + metal scraper + LaCS
Seal resistance value
Table 2 Maximum Seal Resistance Value of Seal SHS SS
Unit: N
For the maximum seal resistance value per
Seal resistance value
LM block when a lubricant is applied on seal
Model No.
SHS SS, refer to the corresponding value
SHS 15
provided in table 2.
SHS 20
7.0
SHS 25
10.5
SHS 30
17.0
SHS 35
20.5
SHS 45
30.0
SHS 55
31.5
SHS 65
43.0
a-138
4.5
a. Dimensions of the LM Guides
a
The table below shows the dimensions of dedicated bellows JSH for model SHS. Specify the
corresponding model number of the desired bellows from the table.
b
H
W
b1
Lmax
Lmin
S
a
t1
W
H1
t4
t3
H1
t2
S1
S1
b2
Models SHS15 to 30
Models SHS35 to 65
Table 3 Dimensional Table for JSH
Major dimensions (mm)
t1
b1 Type C Type V Type R
Model No.
W
H1
b2
t2
t3
t4
Supported
model
JSH 15
53
26
26
15
22.4
SHS 15
JSH 20
60
30
30
17
27.6
7.5
7.5
SHS 20
JSH 25
75
36
36
20
38
9.1
9.1
13.1
SHS 25
JSH 30
80
38
38
20
44
11
11
14
11
SHS 30
JSH 35
86
40.5
40.5
20
50
11
11
18
20
21.5
SHS 35
JSH 45
97
46
46
20
64.6
13.5
13.5
23.5
26
26.5
SHS 45
JSH 55
105
48
48
20
68
13
13
23
30
31.5
SHS 55
JSH 65
126
63
63
25
80
18
18
34
45
SHS 65
Supported
SHS 15
Mounting bolt
S
S1
M28R M48R
SHS 20
model
Other dimensions (mm)
a
Type C Type V Type R Type C
3
b
Type V
Type R
A
Lmax
Lmin
9.5
9.5
13.5
13.5
M2.68R M36R
1.5
SHS 25
M38R M36R
2.5
SHS 30
M310R M36R
10
10
SHS 35
M410R M48R
SHS 45
M412R M48R
15
11.7
5.5
5.5
SHS 55
M512R M510R
19
17.5
2.5
2.5
SHS 65
M614R M612R
22
Note 1: When desiring to use the dedicated bellows other than in horizontal mount (i.e., vertical, wall and inverted
mount), or when desiring a heat-resistant type of bellows, contact
.
Note 2: For lubrication when using the dedicated bellows, contact
.
Note 3: When using the dedicated bellows, the LM block and LM rail need to be machined so that the bellows can be
mounted. Be sure to indicate that the dedicated bellows is required when ordering SHS.
Model number coding
JSH35-60/420
z
zModel number bellows for SHS35
xBellows dimensions (length when compressed /
length when extended)
Note: The length of the bellows is
calculated as follows.
S
Lmin SStroke length (mm)
(A1)
Lmax LminAAExtension rate
a-139
139 Global Standard Type LM Guide Model SHS
Dedicated Bellows JSH for Model SHS
Dedicated Cap C for LM
Rail Mounting Holes
If any of the LM rail mounting holes of an LM
Table 4 Major Dimensions of Dedicated Cap C
Model No.
Cap C
Bolt
model No.
used
Major dimensions mm
D
7.8
1.0
Guide is filled with cutting chips or foreign
SHS 15
C 4
M 4
matter, they may enter the LM block struc-
SHS 20
C 5
M 5
9.8
2.4
ture. Entrance of such foreign matter can be
SHS 25
C 6
M 6
11.4
2.7
prevented by covering each LM rail mounting
SHS 30
C 8
M 8
14.4
3.7
hole with the dedicated cap so that the top of
SHS 35
C 8
M 8
14.4
3.7
the mounting holes are on the same level as
SHS 45
C12
M12
20.5
4.7
the LM rail top face.
SHS 55
C14
M14
23.5
5.7
Since the dedicated cap C for LM rail mount-
SHS 65
C16
M16
26.5
5.7
ing holes uses a special synthetic resin with
D
high oil resistance and high wear resistance,
it is highly durable.
When placing an order, specify the desired
cap type with the corresponding cap number
indicated in table 4.
Dedicated Cap C
For the procedure for mounting the cap, see
page a-22.
Steel Tape SP
By covering the LM rail mounting holes with
an ultra thin stainless steel (SUS304) plate,
the steel tape SP further increases sealability of the end seal, thus to prevent foreign
Steel tape SP
matter and water from entering the top face
of the LM rail.
For the mounting procedure, see page a-28.
Note 1: To mount the steel tape, the LM block
needs to be removed from the LM rail. It
requires an LM block removing/mounting
jig. Contact
for details.
Note 2: When mounting the steel tape, the LM rail
needs to be machined. Indicate that the
steel tape is required when ordering the
LM Guide.
a-140
Fig. 3
Note: The steel tape is available for models SHS15
to 65.
a. Dimensions of the LM Guides
a
When QZ Lubricator is required, specify the desired type with the corresponding symbol indicated in table 5 (for details of QZ Lubricator, see pages a-19 and a-20).
For supported LM Guide model numbers for QZ Lubricator and overall LM block length with QZ
Lubricator attached (dimension L), see page a-150.
Table 5 Parts Symbols for Model SHS with QZ Lubricator Attached
Symbol
Dust prevention accessories for LM Guide with QZ Lubricator attached
QZUU
With end seal + QZ Lubricator
QZSS
With end seal + side seal + inner seal + QZ Lubricator
QZDD
With double seals + side seal + inner seal + QZ Lubricator
QZZZ
With end seal + side seal + inner seal + metal scraper + QZ Lubricator
QZKK
With double seals + side seal + inner seal + metal scraper + QZ Lubricator
QZSSHH
With end seal + side seal + inner seal + LaCS + QZ Lubricator
QZDDHH
With double seals + side seal + inner seal + LaCS + QZ Lubricator
QZZZHH
With end seal + side seal + inner seal + metal scraper + LaCS + QZ Lubricator
QZKKHH
With double seals + side seal + inner seal + metal scraper + LaCS + QZ Lubricator
a-141
141 Global Standard Type LM Guide Model SHS
QZ LubricatorTM
Standard Length and Maximum Length of the LM Rail
Table 6 shows the standard lengths and the maximum lengths of model SHS variations. If the
maximum length of the desired LM rail exceeds them, connected rails will be used.
Contact
for details.
For the G dimension when a special length is required, we recommend selecting the corresponding G value from the table. The longer the G dimension is, the less stable the G area may
become after installation, thus causing an adverse impact to accuracy.
L0
Table 6 Standard Length and Maximum Length of the LM Rail for Model SHS Unit: mm
SHS 15
SHS 20
SHS 25
SHS 30
SHS 35
SHS 45
SHS 55
SHS 65
160
220
280
340
400
460
520
580
640
700
760
820
940
1000
1060
1120
1180
1240
1360
1480
1600
220
280
340
400
460
520
580
640
700
760
820
940
1000
1060
1120
1180
1240
1360
1480
1600
1720
1840
1960
2080
2200
220
280
340
400
460
520
580
640
700
760
820
940
1000
1060
1120
1180
1240
1300
1360
1420
1480
1540
1600
1720
1840
1960
2080
2200
2320
2440
280
360
440
520
600
680
760
840
920
1000
1080
1160
1240
1320
1400
1480
1560
1640
1720
1800
1880
1960
2040
2200
2360
2520
2680
2840
3000
280
360
440
520
600
680
760
840
920
1000
1080
1160
1240
1320
1400
1480
1560
1640
1720
1800
1880
1960
2040
2200
2360
2520
2680
2840
3000
570
675
780
885
990
1095
1200
1305
1410
1515
1620
1725
1830
1935
2040
2145
2250
2355
2460
2565
2670
2775
2880
2985
3090
780
900
1020
1140
1260
1380
1500
1620
1740
1860
1980
2100
2220
2340
2460
2580
2700
2820
2940
3060
1270
1570
2020
2620
Standard pitch F
60
60
60
80
80
105
120
150
20
20
20
20
20
2500
3000
3000
3000
3000
Standard LM rail length (L0)
Model No.
Max length
22.5
3090
30
35
3060
3000
Note 1: The maximum length varies with accuracy grades. Contact
for details.
Note 2: If connected rails are not allowed and a greater length than the maximum values above is required,
contact
.
a-142
a. Dimensions of the LM Guides
Models SHS-C SHS-LC
a
L
L1
**4-D0
e0
C
f0
T1
d2
T
h
M1
d1
W2
W1
F
Unit: mm
External
dimensions
Model No.
15C
15LC
20C
20LC
25C
25LC
30C
30LC
35C
35LC
45C
45LC
55C
55LC
65C
65LC
LM block dimensions
Height Width Length
M
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
Pilot holes for
side nipples**
24
47
30
63
36
70
42
90
48
100
60
120
70
140
90
170
Grease
B
64.4
38
79.4
79
53
98
92
57
109
106
72
131
122
82
152
140
100
174
171
116
213
221
142
272
Model number coding
30
M 5
4.4
40
M 6
5.4
45
M 8
6.8
52
M10
8.5
62
M10
8.5
80
M12 10.5
95
M14 12.5
110
M16 14.5
L1
48
63
59
78
71
88
80
105
93
123
106
140
131
173
175
226
T1
nipple
x c v
a-144
0
0.05
15 16
13
60 4.57.55.3
B-M6F
4.3
5.3 3
20 21.5 16.5 60
12
B-M6F
5.5 3
23 23.5 20
60
7119
12
B-M6F
5.5
5.2
28 31
23
80
91412
12
B-M6F
6.5
5.5 5.2
34 33
26
80
91412
51.1 10.5
16
B-PT1/8
5.2
45 37.5 32
105 142017
21
57.3 11
16
B-PT1/8
10
5.2
53 43.5 38
120 162320
24
71
19
16
B-PT1/8
10
12
5.2
63 53.5 53
150 182622
10
25.4
6.5
12
9.1
12
30.2
7.5
11.5
15
35
11.5
15
40.5
14.1
18
16
18.8
7.2
, . 0
zModel number xType of LM block cNo. of LM blocks used on the same rail vWith QZ Lubricator
bDust prevention accessory symbol (see page a-138) nRadial clearance symbol (see page a-33)
mLM rail length (in mm) ,Accuracy symbol (see page a-38) .With steel tape
0No. of rails used on the same plane
Note
D0
5.5
f0
5.5 PB1021B
21
5.9
SHS25 LC 2 QZ KKHH C0 +1200L P Z -
z
e0
LM rail dimensions
Width
Height Pitch
W1 W2 M1 F d1d2h
Note
69.58.5
Basic load Static permissible moment kN-m*
rating
C
kN
14.2
17.2
22.3
28.1
31.7
36.8
44.8
54.2
62.3
72.9
82.8
100
128
161
205
253
C0
MA
MB
MC LM block LM rail
2 blocks in
2 blocks in
kN 1 block close
1 block
contact 1 block close contact
24.2 0.175
31.9 0.296
38.4 0.334
50.3 0.568
52.4 0.566
64.7 0.848
66.6 0.786
88.8 1.36
96.6 1.38
2.34
127
2.05
126
3.46
166
3.96
197
6.68
259
8.26
320
408 13.3
Mass
kg
0.23
0.898 0.175 0.898 0.16
1.43 0.296 1.43 0.212 0.29
1.75 0.334 1.75 0.361 0.46
2.8
0.568 2.8
0.473 0.61
2.75 0.566 2.75 0.563 0.72
3.98 0.848 3.98 0.696 0.89
4.08 0.786 4.08 0.865 1.34
1.66
6.6
1.36 6.6
1.15
1.9
6.76 1.38 6.76 1.53
2.54
10.9
2.34 10.9
2.01
3.24
10.1
2.05 10.1
2.68
4.19
16.3
3.46 16.3
3.53
5.35
19.3
3.96 19.3
4.9
6.97
31.1
6.68 31.1
6.44
10.7
40.4
8.26 40.4
9.4
13.7
62.6 13.3 62.6 11.9
kg/m
1.3
2.3
3.2
4.5
6.2
10.4
14.5
23.7
Pilot holes for side nipples** are not drilled through in order to prevent foreign matter from entering the product. the product.
will mount grease nipples per your request. Therefore, do not use the side nipple pilot
holes** for purposes other than mounting a grease nipple.
Static permissible moment*: 1 block: static permissible moment value with 1 LM block
2 blocks: static permissible moment value with 2 blocks closely
contacting with each other
This model number indicates that a single-rail unit constitutes one set (i.e., required number of
sets when 2 rails are used in parallel is 2 at a minimum).
Those models equipped with QZ Lubricator cannot have a grease nipple.
Standard Length and Maximum Length of the LM Rail P. a-142
Selecting a Model Number Refer to the "
General Catalog - Technical Descriptions of the Products," provided separately
a-145
145 Global Standard Type LM Guide Model SHS
W
4-S
H through
a. Dimensions of the LM Guides
Models SHS-V SHS-LV
a
e0
L1
**4-D0
C
f0
d2
h
K
M1
d1
W2
W1
Unit: mm
External
dimensions
Model No.
15V
15LV
20V
20LV
25V
25LV
30V
30LV
35V
35LV
45V
45LV
55V
55LV
65V
65LV
LM block dimensions
Height Width Length
M
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
Pilot holes for
side nipples**
24
34
30
44
36
48
42
60
48
70
60
86
70
100
90
126
Model number coding
Grease
B
64.4
79.4
79
98
92
109
106
131
122
152
140
174
171
213
221
272
26
32
35
40
50
60
75
76
C
26
34
36
50
35
50
40
60
50
72
60
80
75
95
70
120
SR
L1
M44
M55
M66.5
M88
M810
M1015
M1215
M1620
48
63
59
78
71
88
80
105
93
123
106
140
131
173
175
226
nipple
xc v
a-146
D0
3
0
0.05
15
60 4.57.55.3
9.5 13
B-M6F
4.3
5.3 3
20 12
12
B-M6F
5.5 3
23 12.5 20
60
7119
12
B-M6F
5.5
5.2
28 16
23
80
91412
40.5
12
B-M6F
6.5
5.5 5.2
34 18
26
80
91412
14.9
51.1
10.5
16
B-PT1/8
5.2
45 20.5 32
105 142017
19.4
57.3
11
16
B-PT1/8
10
5.2
53 23.5 38
120 162320
19.5
71
19
16
B-PT1/8
10
12
5.2
63 31.5 53
150 182622
21
5.5
25.4
6.5
12
30.2
7.5
35
14.7
PB1021B
, . 0
zModel number xType of LM block cNo. of LM blocks used on the same rail vWith QZ Lubricator
bDust prevention accessory symbol (see page a-138) nRadial clearance symbol (see page a-33)
mLM rail length (in mm) ,Accuracy symbol (see page a-38) .With steel tape
0No. of rails used on the same plane
Note
f0
5.5
5.9
SHS30 V 2 QZ KKHH C1 +1240L P Z -
z
e0
LM rail dimensions
Width
Height Pitch
W1 W2 M1 F d1d2h
Note
16.5
60 69.58.5
Basic load Static permissible moment kN-m*
rating
C
kN
14.2
17.2
22.3
28.1
31.7
36.8
44.8
54.2
62.3
72.9
82.8
100
128
161
205
253
C0
MA
MB
Mass
MC LM block LM rail
2 blocks in
2 blocks in
kN 1 block close
1 block
contact 1 block close contact
24.2 0.175 0.898 0.175 0.898 0.16
31.9 0.296 1.43 0.296 1.43 0.212
38.4 0.334 1.75 0.334 1.75 0.361
50.3 0.568 2.8
0.568 2.8
0.473
52.4 0.566 2.75 0.566 2.75 0.563
64.7 0.848 3.98 0.848 3.98 0.696
66.6 0.786 4.08 0.786 4.08 0.865
88.8 1.36 6.6
1.36 6.6
1.15
96.6 1.38 6.76 1.38 6.76 1.53
2.34 10.9
127
2.34 10.9
2.01
2.05 10.1
126
2.05 10.1
2.68
3.46 16.3
166
3.46 16.3
3.53
3.96 19.3
197
3.96 19.3
4.9
6.68 31.1
259
6.68 31.1
6.44
8.26 40.4
320
8.26 40.4
9.4
408 13.3 62.6 13.3 62.6 11.9
kg
0.19
0.22
0.35
0.46
0.54
0.67
0.94
1.16
1.4
1.84
2.54
3.19
4.05
5.23
8.41
10.7
kg/m
1.3
2.3
3.2
4.5
6.2
10.4
14.5
23.7
Pilot holes for side nipples** are not drilled through in order to prevent foreign matter from entering the product.
will mount grease nipples per your request. Therefore, do not use the side nipple pilot
holes** for purposes other than mounting a grease nipple.
Static permissible moment*: 1 block: static permissible moment value with 1 LM block
2 blocks: static permissible moment value with 2 blocks closely
contacting with each other
This model number indicates that a single-rail unit constitutes one set (i.e., required number of
sets when 2 rails are used in parallel is 2 at a minimum).
Those models equipped with QZ Lubricator cannot have a grease nipple.
Standard Length and Maximum Length of the LM Rail P. a-142
Selecting a Model Number Refer to the "
General Catalog - Technical Descriptions of the Products," provided separately
a-147
147 Global Standard Type LM Guide Model SHS
W
4-SR
a. Dimensions of the LM Guides
Models SHS-R SHS-LR
a
4-SR
e0
L1
**4-D
f0
T
h
K
d
F
W2
W1
Unit: mm
External
dimensions
Model No.
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
SHS
15R
25R
25LR
30R
30LR
35R
35LR
45R
45LR
55R
55LR
Pilot holes for
side nipples**
LM block dimensions
Height Width Length
Grease
N
nipple
e0
f0
D0
9.5
5.5
PB1021B
12
B-M6F
9.5 3
11
12
B-M6F
5.5
5.2
28 16
23
47.5
15
12
B-M6F
6.5 12.5 5.2
34 18
26
14.9
61.1
20.5
16
B-PT1/8
18
5.2
45 20.5 32
19.4
67.3
21
16
B-PT1/8
10
18
5.2
53 23.5 38
SR
L1
28
34
26
25
34.2
11.5
45
60
38
55
70
14.7
70
86
80
100
48
71
88
80
105
93
123
106
140
131
173
5.9
48
26
35
50
40
60
50
72
60
80
75
95
M45
40
64.4
92
109
106
131
122
152
140
174
171
213
35
40
50
60
75
M68
M810
M812
M1017
M1218
Note
Model number coding
SHS45 LR 2 QZ KKHH C0 +1200L P -
z
x c v
LM rail dimensions
Width
Height Pitch
W1 W2 M1 F d1d2h
, .
0
0.05
15
9.5 13
23 12.5 20
Basic load Static permissible moment kN-m*
rating
C
kN
60 4.57.55.3 14.2
31.7
60 7119
36.8
44.8
80 91412
54.2
62.3
80 91412
72.9
82.8
105 142017
100
128
120 162320
161
C0
MA
MB
MC LM block LM rail
2 blocks in
2 blocks in
kN 1 block close
1 block
contact 1 block close contact
24.2
52.4
64.7
66.6
88.8
96.6
127
126
166
197
259
0.175
0.566
0.848
0.786
1.36
1.38
2.34
2.05
3.46
3.96
6.68
0.898
2.75
3.98
4.08
6.6
6.76
10.9
10.1
16.3
19.3
31.1
0.175
0.566
0.848
0.786
1.36
1.38
2.34
2.05
3.46
3.96
6.68
0.898
2.75
3.98
4.08
6.6
6.76
10.9
10.1
16.3
19.3
31.1
Mass
0.16
0.563
0.696
0.865
1.15
1.53
2.01
2.68
3.53
4.9
6.44
kg
kg/m
0.22
0.66
0.8
1.04
1.36
1.8
2.34
3.24
4.19
5.05
6.57
1.3
3.2
4.5
6.2
10.4
14.5
Pilot holes for side nipples** are not drilled through in order to prevent foreign matter from entering the product.
will mount grease nipples per your request. Therefore, do not use the side nipple pilot
holes** for purposes other than mounting a grease nipple.
Static permissible moment*: 1 block: static permissible moment value with 1 LM block
2 blocks: static permissible moment value with 2 blocks closely
contacting with each other
zModel number xType of LM block cNo. of LM blocks used on the same rail vWith QZ Lubricator
bDust prevention accessory symbol (see page a-138) nRadial clearance symbol (see page a-33)
mLM rail length (in mm) ,Accuracy symbol (see page a-38) .No. of rails used on the same plane
Note
a-148
This model number indicates that a single-rail unit constitutes one set (i.e., required number of
sets when 2 rails are used in parallel is 2 at a minimum).
Those models equipped with QZ Lubricator cannot have a grease nipple.
Standard Length and Maximum Length of the LM Rail P. a-142
Selecting a Model Number Refer to the "
General Catalog - Technical Descriptions of the Products," provided separately
a-149
149 Global Standard Type LM Guide Model SHS
Overall LM Block Length with Options
Overall LM Block Length (Dimension L) of Model SHS with a Dust
Prevention Accessory Attached
Unit: mm
Model No.
UU
SS
DD
ZZ
KK
SSHH
DDHH
ZZHH
KKHH
SHS 15C/V/R
64.4
64.4
69.8
66.8
72.2
78.9
84.4
79.9
85.2
SHS 15LC/LV
79.4
79.4
84.8
81.8
87.2
93.9
99.4
94.9
100.2
SHS 20C/V
79
79
85.4
83
89.4
94
100
96
102.5
SHS 20LC/LV
98
98
104.4
102
108.4
113
119
115
121.5
SHS 25C/V/R
92
92
101.6
100.4
107.6
112
119.2
114.4
121.6
SHS 25LC/LV/LR
109
109
118.6
117.4
124.6
129
136.2
131.4
138.6
SHS 30C/V/R
106
106
116
113.8
122.4
129.4
138
131.8
140.4
SHS 30LC/LV/LR
131
131
141
138.8
147.4
154.4
163
156.8
165.4
SHS 35C/V/R
122
122
134.8
132.4
142.2
148
157.8
150.4
160.2
SHS 35LC/LV/LR
152
152
164.8
162.4
172.2
178
187.8
180.4
190.2
SHS 45C/V/R
140
140
152.8
151.2
161
169
178.8
172.2
182
SHS 45LC/LV/LR
174
174
186.8
185.2
195
203
212.8
206.2
216
SHS 55C/V/R
171
171
186.6
184.2
195.4
202
213.2
205.2
216.4
SHS 55LC/LV/LR
213
213
228.6
226.2
237.4
244
255.2
247.2
258.4
SHS 65C/V
221
221
238.6
236.2
248.6
258
270.4
261.2
273.6
SHS 65LC/LV
272
272
289.6
287.2
299.6
309
321.4
312.2
324.6
Overall LM Block Length (Dimension L) of Model SHS with QZ
Lubricator Attached
Unit: mm
QZUU
QZSS
QZDD
QZZZ
SHS 15C/V/R
84.4
84.4
89.8
86.8
92.2
100.4
105.4
101.4
106.9
SHS 15LC/LV
99.4
99.4
104.8
101.8
107.2
115.4
120.4
116.4
121.9
SHS 20C/V
99
99
105.4
103
109.4
115.5
122
118
124.5
SHS 20LC/LV
118
118
124.4
122
128.4
134.5
141
137
143.5
SHS 25C/V/R
114.4
114.4
121.6
120.4
127.6
132
139.2
134.4
141.6
SHS 25LC/LV/LR
131.4
131.4
138.6
137.4
144.6
149
156.2
151.4
158.6
SHS 30C/V/R
127.4
127.4
136
133.8
142.4
149.4
158
151.8
160.4
SHS 30LC/LV/LR
152.4
152.4
161
158.8
167.4
174.4
183
176.8
185.4
SHS 35C/V/R
145
145
154.8
152.4
162.2
168
177.8
170.4
180.2
SHS 35LC/LV/LR
175
175
184.8
182.4
192.2
198
207.8
200.4
210.2
SHS 45C/V/R
173
173
182.8
181.2
191
199
208.8
202.2
212
SHS 45LC/LV/LR
207
207
216.8
215.2
225
233
242.8
236.2
246
SHS 55C/V/R
205.4
205.4
216.6
214.2
225.4
232
243.2
235.2
246.4
SHS 55LC/LV/LR
247.4
247.4
258.6
256.2
267.4
274
285.2
277.2
288.4
SHS 65C/V
256.2
256.2
268.6
266.2
278.6
288
300.4
291.2
303.6
SHS 65LC/LV
307.2
307.2
319.6
317.2
329.6
339
351.4
342.2
354.6
Model No.
a-150
QZKK QZSSHH QZDDHH QZZZHH QZKKHH
a. Dimensions of the LM Guides
Service temperature range of LaCS: -20
C
Table 7 Resistance of LaCS
to +80
C
Resistance of LaCS: indicated in table 7
Unit: N
Model No.
Resistance of LaCS
SHS 15
5.2
SHS 20
6.5
SHS 25
11.7
SHS 30
18.2
SHS 35
20.8
SHS 45
26.0
SHS 55
32.5
SHS 65
39.0
Note 1: Each resistance value in the table only
consists of that of LaCS, and does not
include sliding resistances of seals and
other accessories.
Note 2: For the maximum service speed of LaCS,
contact
.
a-151
151 Global Standard Type LM Guide Model SHS
Basic Specifications of LaCS
Grease Nipple
Those LM Guide models without QZ Lubricator are equipped with a grease nipple. Fig. 4 shows
the mounting location for the grease nipple.
Please note that attaching the grease nipple
increases the LM block width.
For LM Guide Models with Dust Prevention Accessories SSHH,
DDHH, ZZHH or KKHH
LM Guide models with dust prevention accessories SSHH, DDHH, ZZHH or KKHH have the
grease nipple in the location indicated in Fig. 4.
Table 8 shows incremental dimensions with the grease nipple.
Grease nipple mounting location for model SHS
Grease nipple
LaCS
Endplate
K Datum
plane
Fig. 4
Note: When desiring the mounting location for the
grease nipple other than the one indicated in
Fig. 4, contact
.
Model No.
Table 8
Unit: mm
Incremental dimension
with grease nipple H Nipple type
4.7
4.5
4.7
7.4
7.4
7.7
7.4
6.9
SHS 15C/LC
SHS 15R/V/LV
SHS 20C/LC
SHS 20V/LV
SHS 25C/LC
SHS 25R/LR/V/LV
SHS 30C/LC
SHS 30R/LR/V/LV
SHS 35C/LC
SHS 35R/LR/V/LV
SHS 45C/LC
SHS 45R/LR/V/LV
SHS 55C/LC
SHS 55R/LR/V/LV
SHS 65C/LC
SHS 65V/LV
PB107
PB107
PB107
PB107
PB107
PB107
A-M6F
A-M6F
A-M6F
A-M6F
A-M6F
A-M6F
A-M6F
A-M6F
A-M6F
A-M6F
For LM Guide Models with Dust Prevention Accessories UU or SS
For the mounting location of the grease nipple (N) and its incremental dimension (E) when dust
prevention accessories UU or SS are attached, see the corresponding table of dimensions.
For LM Guide Models with Dust Prevention Accessories DD, ZZ or KK
For the mounting location of the grease nipple and its incremental dimension when dust prevention accessories DD, ZZ or KK are attached, contact
Model number coding
SHS25 C 2 QZ KKHH C1 +760L P
z
zLM Guide model number
xQZ
: with QZ Lubricator, without grease nipple
No symbol: without QZ Lubricator, with grease nipple (see Fig. 4)
cDust prevention accessory symbol (see page a-138)
Note 1: QZ Lubricator and LaCS are not sold alone.
Note 2: Those models equipped with QZ Lubricator cannot have a grease nipple. When desiring both QZ
Lubricator and LaCS to be attached, contact
.
a-152
a. Dimensions of the LM Guides
Laminated Contact Scraper LaCS for
LM Guides
Service environment
Be sure the service temperature range of Laminated Contact Scraper LaCS is between -20
C
and +80
C, and do not clean LaCS in an organic solvent or white kerosene, or leave it
unpacked.
Impregnating oil
The lubricant impregnated into Laminated Contact Scraper LaCS is used to increase the sliding capability of LaCS itself. For lubrication of the LM Guide, attach QZ Lubricator or the
grease nipple.
Function
The intended role of Laminated Contact Scraper LaCS is to remove foreign matter or liquids.
To seal oils, end seals are needed.
Design
When using Laminated Contact Scraper LaCS, be sure to use the dedicated cap C for LM rail
mounting holes or an appropriate form of cover.
QZ Lubricator for
LM Guides
Handling
Dropping or hitting this product may damage it. Take much care when handling it.
Do not clean it with an organic solvent or white kerosene.
Do not leave it unpacked for a long period of time.
Do not block the air vent with grease or the like.
Service temperature range
Be sure the service temperature of this product is between -10
C and +50
C.
Use in a special environment
When using it in a special environment, contact
Precaution on selection
Be sure the stroke is longer than the overall length of the LM block length attached with QZ
Lubricator.
Corrosion prevention of LM Guides
QZ Lubricator is a lubricating device designed to feed a minimum amount of oil to the ball
raceway of LM rails, and does not provide corrosion prevention to the whole LM Guide. When
using it in an environment subject to a coolant or the like, we strongly recommend taking an
anti-corrosion measure.
a-153
153 Global Standard Type LM Guide Model SHS
Precautions on Use
