Technology Corporation

ProLight PP6M-1LFP-3SC
3W RGB Power LED Module
Technical Datasheet
Version: 1.3

Features
● R, G, B three color in one Package
● High Flux per LED

● Good color uniformity

● RoHS compliant

● More energy efficient than incandescent and

most halogen lamps

● Low Voltage DC operated

● Instant light (less than 100ns)

● No UV

Typical Applications
● Reading lights (car, bus, aircraft)
● Uplighters/Downlighters

● Decorative/Entertainment
● Bollards/Security/Garden

● Cove/Undershelf/Task
● Indoor/Outdoor Commercial and

Residential Architectural

1 2009/02
Module Mechanical Dimensions

Notes:
1. Electrical interconnection pads labeled on the aluminum-core PCB with "+" and "-" to denote
positive and negative, respectively. All positive pads are interconnected, as are all negative pads,
allowing for flexibility in array interconnection.
2. Drawing not to scale.
3. All dimensions are in millimeters.
4. All dimendions without tolerances are for reference only.
5. Please do not use a force of over 3kgf impact or pressure on the lens of the LED, otherwise
it will cause a catastrophic failure.

*The appearance and specifications of the product may be modified for improvement without notice.

2
Flux Characteristics at 150mA, T J = 25°C
Radiation Part Number Lumious Flux ΦV (lm)
Color
Pattern Module Minimum Typical

Green 58.9 66
Lambertian Blue PP6M-1LFP-3SC 10.7 14
Red 30.6 40

● ProLight maintains a tolerance of ± 10% on flux and power measurements.

● Please do not drive at rated current more than 5 second without proper heat sink.

Electrical Characteristics at 150mA, T J = 25°C

Temperature Thermal
Coefficient of Resistance
Forward Voltage VF (V) Dynamic VF (mV/ °C) Junction to
Color Min. Typ. Max. Resistance (Ω) ΔVF/ ΔTJ Board (°C/ W)

Green 8.4 10.5 12.9 1.0 -2.0 5

Blue 8.4 10.5 12.9 1.0 -2.0 5
Red 5.7 6.6 9.3 2.4 -2.0 5

Optical Characteristics at 150mA, T J = 25°C

Temperature
Coefficient of Total
Dominant Wavelength λD, Spectral Dominant included Viewing
or Color Temperature CCT Half-width Wavelength Angle Angle
Radiation (nm) (nm/ °C) (degrees) (degrees)
Color
Pattern Min. Typ. Max. Δλ1/2 ΔλD/ ΔTJ θ0.90V 2 θ1/2

Green 515 nm 525 nm 535 nm 35 0.04 160 140

Lambertian Blue 455 nm 465 nm 475 nm 25 0.04 160 140
Red 613.5 nm 623 nm 631 nm 20 0.05 160 140

● ProLight maintains a tolerance of ± 1nm for dominant wavelength measurements.

3
Absolute Maximum Ratings
Parameter Green/Blue/Red

DC Forward Current (mA) 150

Peak Pulsed Forward Current (mA) 250
Average Forward Current (mA) 150
ESD Sensitivity
> ±500V
(HBM per MIL-STD-883E Method 3015.7
LED Junction Temperature (°C) 120
Aluminum-core PCB Temperature (°C) 105
Storage & Operating Temperature (°C) -40 to +105

Dominant Wavelength Bin Structure

Minimum Dominant Maximum Dominant
Color Bin Code
Wavelength (nm) Wavelength (nm)

A 515 520
1 520 525
Green
2 525 530
3 530 535

A 455 460
1 460 465
Blue
2 465 470
3 470 475

2 613.5 620.5
Red
4 620.5 631.0

● ProLight maintains a tolerance of ± 1nm for dominant wavelength measurements.

Note: Although several bins are outlined, product availability in a particular bin varies by production run
and by product performance. Not all bins are available in all colors.

4
Color Spectrum, TJ = 25°C

1.0
Blue Green Red
Relative Spectral Power

0.8
Distribution

0.6

0.4

0.2

0.0
400 450 500 550 600 650 700
Wavelength(nm)

Light Output Characteristics

Relative Light Output vs. Junction Temperature at 150mA

160
Green
140 Blue
Relative Light Output (%)

Red
120

100

80

60

40

20

0
1
-20 02 3
20 4
40 5
60 6
80 7
100 8
120
Junction Temperature, T J (℃)

5
Forward Current Characteristics, TJ = 25°C

1. Forward Voltage vs. Forward Current

160 160
Green, Blue Red
Average Forward Current (mA)

Average Forward Current (mA)

140 140
120 120
100 100
80 80
60 60
40 40
20 20
0 0
0 2 4 6 8 10 12 0 2 4 6 8 10 12
Forward Voltage (V) Forward Voltage (V)

2. Forward Current vs. Normalized Relative Luminous Flux

1.2 1.2
Green, Blue Red
1.0 1.0
Relative Luminous Flux
Relative Luminous Flux

0.8 0.8

0.6 0.6

0.4 0.4

0.2 0.2
0.0 0.0
0 50 100 150 200 0 50 100 150 200
Forward Current (mA) Forward Current (mA)

6
Ambient Temperature vs. Maximum Forward Current
1. Green, Blue (TJMAX = 120°C)

180

150
Forward Current (mA)

120

90 RθJ-A = 60°C/W

60 RθJ-A = 50°C/W
RθJ-A = 40°C/W
30
RθJ-A = 30°C/W
0
0 25 50 75 100 125 150
Ambient Temperature (℃)

2. Red (TJMAX = 120°C)

180

150
Forward Current (mA)

120

90 RθJ-A = 60°C/W
RθJ-A = 50°C/W
60
RθJ-A = 40°C/W
30 RθJ-A = 30°C/W

0
0 25 50 75 100 125 150
Ambient Temperature (℃)

7
Typical Representative Spatial Radiation Pattern
Lambertian Radiation Pattern

100
90
Relative Intensity (%)

80
70
60
50
40
30
20
10
0
-100 -80 -60 -40 -20 0 20 40 60 80 100

Angular Displacement (Degrees)

Collimator Options
Collimator Part Number Collimator Outline

PP6N-3N25

● Please refer to the datasheet of PP6N-3N25 for the details

8
Qualification Reliability Testing
Stress Test Stress Conditions Stress Duration Failure Criteria
Room Temperature
25°C, IF = max DC (Note 1) 1000 hours Note 2
Operating Life (RTOL)
Wet High Temperature
85°C/60%RH, IF = max DC (Note 1) 1000 hours Note 2
Operating Life (WHTOL)
Wet High Temperature
85°C/85%RH, non-operating 1000 hours Note 2
Storage Life (WHTSL)
High Temperature
110°C, non-operating 1000 hours Note 2
Storage Life (HTSL)
Low Temperature
-40°C, non-operating 1000 hours Note 2
Storage Life (LTSL)
Non-operating -40°C to 120°C, 30 min. dwell,
200 cycles Note 2
Temperature Cycle (TMCL) <5 min. transfer
Non-operating -40°C to 120°C, 20 min. dwell,
200 cycles Note 2
Thermal Shock (TMSK) <20 sec. transfer

Notes:
1. Depending on the maximum derating curve.
2. Criteria for judging failure
Criteria for Judgement
Item Test Condition
Min. Max.
Forward Voltage (VF) IF = max DC - Initial Level x 1.1
Luminous Flux or
IF = max DC Initial Level x 0.7 -
Radiometric Power (ΦV)
Reverse Current (IR) VR = 5V - 50 μA
* The test is performed after the LED is cooled down to the room temperature.

3. A failure is an LED that is open or shorted.

9
Precaution for Use
● Storage
Please do not open the moisture barrier bag (MBB) more than one week. This may cause the
leads of LED discoloration. We recommend storing ProLight’s LEDs in a dry box after opening
the MBB. The recommended storage conditions are temperature 5 to 30°C and humidity less
than 40% RH. It is also recommended to return the LEDs to the MBB and to reseal the MBB.
● The slug is is not electrically neutral. Therefore, we recommend to isolate the heat sink.

● The slug is to be soldered. If not, please use the heat conductive adhesive.

● Any mechanical force or any excess vibration shall not be accepted to apply during cooling

process to normal temperature after soldering.

● Please avoid rapid cooling after soldering.

● Components should not be mounted on warped direction of PCB.

● Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,

a heat plate should be used. It should be confirmed beforehand whether the characteristics of
the LEDs will or will not be damaged by repairing.
● This device should not be used in any type of fluid such as water, oil, organic solvent and etc.

When cleaning is required, isopropyl alcohol should be used.

● When the LEDs are illuminating, operating current should be decide after considering the

package maximum temperature.

● The appearance, specifications and flux bin of the product may be modified for improvement

without notice. Please refer to the below website for the latest datasheets.
http://www.prolightopto.com/

Handling of Silicone Lens LEDs

Notes for handling of silicone lens LEDs
● Please do not use a force of over 3kgf impact or pressure on the silicone lens,

otherwise it will cause a catastrophic failure.

● The LEDs should only be picked up by making contact with the sides of the LED body.

● Avoid touching the silicone lens especially by sharp tools such as Tweezers.

● Avoid leaving fingerprints on the silicone lens.

● Please store the LEDs away from dusty areas or seal the product against dust.

● When populating boards in SMT production, there are basically no restrictions

regarding the form of the pick and place nozzle, except that mechanical pressure
on the silicone lens must be prevented.
● Please do not mold over the silicone lens with another resin. (epoxy, urethane, etc)

╳
10