Technology Corporation

ProLight PG1x-3LLE
3W UV Power LED
Technical Datasheet
Version: 1.0

Features
● Very long operating life (up to 100k hours)
● Instant light (less than 100ns)
● Industry best moisture senstivity level - JEDEC 2a

4 week floor life without reconditioning

● Low-temp. & lead free reflow soldering

● RoHS compliant

● Cool beam, safe to the touch

● Superior ESD protection

Typical Applications
● UV gluing, UV curing, UV marking
● UV drying of printing inks and lacquers
● Currency inspection

● Forensic analysis - urine, protein stains

● Leak detection using fluorescent dyes

● Detects fluorescing minerals and gems

1 2008/10
Emitter Mechanical Dimensions

Lambertian - Standard Emitter

TOP VIEW BOTTOM VIEW

Lambertian - Low Profile Emitter

TOP VIEW BOTTOM VIEW

Notes:
1. The cathode side of the device is denoted by a hole in the lead frame.
2. Electrical insulation between the case and the board is required --- slug of device is not
electrically neutral. Do not electrically connect either the anode or cathode to the slug.
3. Drawing not to scale.
4. All dimensions are in millimeters.
5. All dimendions without tolerances are for reference only.
6. Please do not bend the leads of the LED, otherwise it will damage the LED.
7. Please do not use a force of over 3kgf impact or pressure on the lens of the LED, otherwise
it will cause a catastrophic failure.

*The appearance and specifications of the product may be modified for improvement without notice.

2
Part Number
Color Standard Emitter Low Profile Emitter Radiation Pattern

UV PG1A-3LLE PG1N-3LLE Lambertian

Flux Characteristics at 700mA, TJ = 25°C

Radiometric Power (mW)
Color Radiation Pattern
Minimum Typical

UV 225 330 Lambertian

● ProLight maintains a tolerance of ± 10% on flux and power measurements.

● Please do not drive at rated current more than 1 second without proper heat sink.

Optical Characteristics at 700mA, TJ = 25°C

Temperature
Spectral Coefficient or
Peak Wavelength λp
Half-width (nm) Dominant Wavelength
Color Min. Typ. Max. Δλ1/2 ΔλD/ ΔTJ (nm/ °C)

UV 390 nm 400 nm 410 nm 20 --

● ProLight maintains a tolerance of ± 1nm for peak wavelength measurements.

Optical Characteristics at 700mA, TJ = 25°C ( Continued)

Total Included Angle Viewing Angle Typical Candela
Color Radiation Pattern θ0.90V (degrees) 2 θ1/2 (degrees) on Axis (cd)

UV Lambertian 160 140 --

Electrical Characteristics at 700mA, TJ = 25°C

Temperature Thermal
Coefficient of Resistance
Forward Voltage VF (V) Dynamic VF (mV/ °C) Junction to
Color Min. Typ. Max. Resistance (Ω) ΔVF/ ΔTJ Slug (°C/ W)

UV 3.0 3.6 4.3 1.0 -2 10

3
Absolute Maximum Ratings
Parameter UV

DC Forward Current (mA) 700

Peak Pulsed Forward Current (mA) 1000
Average Forward Current (mA) 700
ESD Sensitivity ±4000V (Class III)
(HBM per MIL-STD-883E Method 3015.7)
LED Junction Temperature (℃) 120
Aluminum-core PCB Temperature (℃) 105
Storage & Operating Temperature (℃) -40 to +105
Soldering Temperature (℃) 235°C

Radiometric Power Bin Structure

Minimum Radiometric Maximum Radiometric
Color Bin Code
Power (mW) Power (mW)

M 225 275
N 275 335
UV
P 335 435
*When peak wavelength is less than 400nm, P bin is not available.

● ProLight maintains a tolerance of ± 10% on flux and power measurements.

● The flux bin of the product may be modified for improvement without notice.

Peak Wavelength Bin Structure

Minimum Peak Maximum Peak
Color Bin Code
Wavelength (nm) Wavelength (nm)

1 390 395
2 395 400
UV
3 400 405
4 405 410

● ProLight maintains a tolerance of ± 1nm for peak wavelength measurements.

4
UV Color Spectrum

1.0
Relative Spectral Power

0.8
Distribution

0.6

0.4

0.2

0.0
360 380 400 420 440 460 480 500
Wavelength(nm)

Forward Current Characteristics, Tj=25℃

400
800 1.2
1.2
Average Forward Current (mA)
Average Forward Current (mA)

350
700 1.0
1.0
Flux

300
LuminousFlux

600
250 0.8
0.8
500
Relative Luminous

200
400 0.6
0.6
150
300 0.4
0.4
100
Relative

200
0.2
0.2
50
100
0 0.0
0.0
0 0.5
0.5 11 1.5
1.5 22 2.5
2.5 33 3.5
3.5 4 4 00 100
200 200
400 300
600 400
800
ForwardVoltage
Forward Voltage(V)
(V) Forward Current (mA)
Forward Current (mA)

Fig 1. Forward Current vs. Fig 2. Relative Luminous Flux vs.

Forward Voltage Forward Current at
Tj=25℃ maintained.

5
Ambient Temperature vs. Maximum Forward Current
UV (TJMAX = 120°C)

400
800
350
700
Forward Current (mA)

300
600
250
500
RθJ-A = 60°C/W
200
400 RθJ-A = 30°C/W
RθJ-A = 50°C/W
150
300 RθJ-A = 25°C/W
RθJ-A = 40°C/W
100
200 RθJ-A = 20°C/W
RθJ-A = 30°C/W
100
50 RθJ-A = 15°C/W

0
0 25 50 75 100 125 150
Ambient Temperature (℃)

Typical Representative Spatial Radiation Pattern

Lambertian Radiation Pattern

1
0.9
0.8
0.7
Relative Intensity

0.6
0.5
0.4
0.3
0.2
0.1
0
-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
Angular Displacement (Degrees)

6
Moisture Sensitivity Level - JEDEC 2a

Soak Requirements
Level Floor Life Standard Accelerated Environment
Time Conditions Time (hours) Conditions Time (hours) Conditions
≤30°C / 30°C / 60°C /
2a 4 weeks 696 +5/-0 120 +1/-0
60% RH 60% RH 60% RH

● The standard soak time includes a default value of 24 hours for semiconductor manufature's
exposure time (MET) between bake and bag and includes the maximum time allowed out of
the bag at the distributor's facility.
● Table below presents the moisture sensitivity level definitions per IPC/JEDEC's J-STD-020C.

Soak Requirements
Level Floor Life Standard Accelerated Environment
Time Conditions Time (hours) Conditions Time (hours) Conditions
≤30°C / 85°C /
1 Unlimited 168 +5/-0 NA NA
85% RH 85% RH
≤30°C / 85°C /
2 1 year 168 +5/-0 NA NA
60% RH 60% RH
≤30°C / 30°C / 60°C /
2a 4 weeks 696 +5/-0 120 +1/-0
60% RH 60% RH 60% RH
≤30°C / 30°C / 60°C /
3 168 hours 192 +5/-0 40 +1/-0
60% RH 60% RH 60% RH
≤30°C / 30°C / 60°C /
4 72 hours 96 +2/-0 20 +0.5/-0
60% RH 60% RH 60% RH
≤30°C / 30°C / 60°C /
5 48 hours 72 +2/-0 15 +0.5/-0
60% RH 60% RH 60% RH
≤30°C / 30°C / 60°C /
5a 24 hours 48 +2/-0 10 +0.5/-0
60% RH 60% RH 60% RH
Time on Label ≤30°C / Time on Label 30°C /
6 NA NA
(TOL) 60% RH (TOL) 60% RH

7
Qualification Reliability Testing
Stress Test Stress Conditions Stress Duration Failure Criteria
Room Temperature
25°C, IF = max DC (Note 1) 1000 hours Note 2
Operating Life (RTOL)
Wet High Temperature
85°C/60%RH, IF = max DC (Note 1) 1000 hours Note 2
Operating Life (WHTOL)
Wet High Temperature
85°C/85%RH, non-operating 1000 hours Note 2
Storage Life (WHTSL)
High Temperature
110°C, non-operating 1000 hours Note 2
Storage Life (HTSL)
Low Temperature
-40°C, non-operating 1000 hours Note 2
Storage Life (LTSL)
Non-operating -40°C to 120°C, 30 min. dwell,
200 cycles Note 2
Temperature Cycle (TMCL) <5 min. transfer
Non-operating -40°C to 120°C, 20 min. dwell,
200 cycles Note 2
Thermal Shock (TMSK) <20 sec. transfer
1500 G, 0.5 msec. pulse,
Mechanical Shock Note 3
5 shocks each 6 axis

Natural Drop On concrete from 1.2 m, 3X Note 3

Variable Vibration 10-2000-10 Hz, log or linear sweep rate,

Note 3
Frequency 20 G about 1 min., 1.5 mm, 3X/axis
Solder Heat Resistance
260°C ± 5°C, 10 sec. Note 3
(SHR)
Steam age for 16 hrs., then solder dip Solder coverage
Solderability
at 260°C for 5 sec. on lead

Notes:
1. Depending on the maximum derating curve.
2. Criteria for judging failure
Criteria for Judgement
Item Test Condition
Min. Max.
Forward Voltage (VF) IF = max DC - Initial Level x 1.1
Luminous Flux or
IF = max DC Initial Level x 0.7 -
Radiometric Power (ΦV)
Reverse Current (IR) VR = 5V - 50 μA
* The test is performed after the LED is cooled down to the room temperature.

3. A failure is an LED that is open or shorted.

8
Recommended Solder Pad Design

Standard Emitter

Low Profile Emitter

● All dimensions are in millimeters.

● Electrical isolation is required between Slug and Solder Pad.

9
Reflow Soldering Condition
Low-Temp. & Pb-Free Assembly
Profile Feature Sn-Pb Eutectic Assembly
(58Bi-42Sn Eutectic Alloy)
Preheat & Soak
Temperature min (T smin) 100 °C 90 °C
Temperature max (T smax) 150 °C 120 °C
Time (T smin to T smax) 60-120 seconds 60-120 seconds
Average Ramp-Up Rate (Tsmax to T P) 3 °C / second max. 2 °C / second max.
Liquidous temperature (TL) 183°C 138°C
Time at liquidous (t L) 60-150 seconds 20-50 seconds
Peak package body temperature (TP) 235°C 185°C
Time (t P) within 5°C of the specified
20 seconds 20 seconds
classification temperature (T C)
Average ramp-down rate (TP to Tsmax) 6 °C/second max. 3 °C/second max.
Time 25°C to Peak Temperature 6 minutes max. 4 minutes max.

● All temperatures refer to topside of the package, measured on the package body surface.
● Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,
a heat plate should be used. It should be confirmed beforehand whether the characteristics of
LEDs will or will not be damaged by repairing.
● Reflow soldering should not be done more than two times.
● When soldering, do not put stress on the LEDs during heating.
● After soldering, do not warp the circuit board.

10
Heat Plate Soldering Condition
(1) Soldering Process for Solder Paste (2) Soldering Process for Solder Wire

Solder Paste

MCPCB

Heat Plate
MCPCB
Use Solder Mask to print Solder Paste on MCPCB. Put MCPCB on Heat Plate.

Emitter Solder Wire

Heat Plate

Place Emitter on MCPCB. Place Solder Wire to the solder pad of MCPCB.

Emitter

Heat Plate Heat Plate

Put MCPCB on Heat Plate until Solder Paste melt. Put Emitter on MCPCB. Take the MCPCB out
The Solder Paste sould be melted within 10 seconds. from Heat Plate within 10 seconds.
Take out MCPCB out from Heat Plate within 15 seconds.

● Heat plate temperature: 230°C max for Lead Solder and 230°C max for Lead-Free Solder.
● We recommend using the 58Bi-42Sn eutectic alloy for low-temp. and lead free soldering (melting point = 138 °C).
● When soldering, do not put stress on the LEDs during heating.
● After soldering, do not warp the circuit board.

Manual Hand Soldering

Thermal Conductive Glue Solder Wire
MCPCB Soldering Iron
Emitter

Place Thermal Comductive Glue Place Emitter on the MCPCB. Use Soldering Iron to solder the
on the MCPCB. leads of Emtter within 5 seconds.
● For prototype builds or small series production runs it possible to place and solder the emitters by hand.
● Solder tip temperature: 230°C max for Lead Solder and 260°C max for Lead-Free Solder.
● Avoiding damage to the emitter or to the MCPCB dielectric layer. Damage to the epoxy layer can cause

a short circuit in the array.

● Do not let the solder contact from solder pad to back-side of MCPCB. This one will cause a short circuit

and damage emitter.

11
Emitter Tube Packaging

Notes:
1. 50pieces per tube.
2. Drawing not to scale.
3. All dimensions are in millimeters.
4. All dimendions without tolerances are for reference only.

**Please do not open the moisture barrier bag (MBB) more than one week. This may cause the leads
of LED discoloration. We recommend storing ProLight’s LEDs in a dry box after opening the MBB.
The recommended storage conditions are temperature 5 to 30°C and humidity less than 40% RH.

12
Precaution for Use
● Storage
Please do not open the moisture barrier bag (MBB) more than one week. This may cause the
leads of LED discoloration. We recommend storing ProLight’s LEDs in a dry box after opening
the MBB. The recommended storage conditions are temperature 5 to 30°C and humidity less
than 40% RH. It is also recommended to return the LEDs to the MBB and to reseal the MBB.
● The slug is is not electrically neutral. Therefore, we recommend to isolate the heat sink.

● The slug is to be soldered. If not, please use the heat conductive adhesive.

● Any mechanical force or any excess vibration shall not be accepted to apply during cooling

process to normal temperature after soldering.

● Please avoid rapid cooling after soldering.

● Components should not be mounted on warped direction of PCB.

● Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,

a heat plate should be used. It should be confirmed beforehand whether the characteristics of
the LEDs will or will not be damaged by repairing.
● This device should not be used in any type of fluid such as water, oil, organic solvent and etc.

When cleaning is required, isopropyl alcohol should be used.

● When the LEDs are illuminating, operating current should be decide after considering the

package maximum temperature.

● The appearance, specifications and flux bin of the product may be modified for improvement

without notice. Please refer to the below website for the latest datasheets.
http://www.prolightopto.com/

Handling of Silicone Lens LEDs

Notes for handling of silicone lens LEDs
● Please do not use a force of over 3kgf impact or pressure on the silicone lens,

otherwise it will cause a catastrophic failure.

● The LEDs should only be picked up by making contact with the sides of the LED body.

● Avoid touching the silicone lens especially by sharp tools such as Tweezers.

● Avoid leaving fingerprints on the silicone lens.

● Please store the LEDs away from dusty areas or seal the product against dust.

● When populating boards in SMT production, there are basically no restrictions

regarding the form of the pick and place nozzle, except that mechanical pressure
on the silicone lens must be prevented.
● Please do not mold over the silicone lens with another resin. (epoxy, urethane, etc)

╳ ○
13