Scribd
Upload
173 views

Control Engineering Stability

1. The document discusses the concepts of stability for linear control systems, including absolute and relative stability. 2. A stable system is defined as one where the output is bounded for a bounded input. The stability of a system depends on the location of its poles - a system is stable if all poles are in the left half of the s-plane. 3. The root locus method can be used to analyze how the location of a system's poles varies with changes in a system parameter like a controller gain K. The root locus traces the path of the poles in the s-plane as K varies.

Uploaded by

Ahmad Azree Othman
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
173 views

Control Engineering Stability

1. The document discusses the concepts of stability for linear control systems, including absolute and relative stability. 2. A stable system is defined as one where the output is bounded for a bounded input. The stability of a system depends on the location of its poles - a system is stable if all poles are in the left half of the s-plane. 3. The root locus method can be used to analyze how the location of a system's poles varies with changes in a system parameter like a controller gain K. The root locus traces the path of the poles in the s-plane as K varies.

Uploaded by

Ahmad Azree Othman
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 23

Stability of Linear Control System

Concept of Stability
Closed-loop feedback system is either stable or unstable.

This type of

characterization is referred to as absolute stability. Given that the system is


stable, the degree of stability of the system is referred to as relative stability.

A stable system is defined as a system with bounded response to a bounded


input.
Bounded input
signal

Output signal
system

impulse

step

Bounded output
signal - system
stable

Output signal
unbounded
unstable system

Consider the concept of stability for cones shown below.

Example 3.1
Obtain the time response of the system shown below for a unit step input
U(s) = 1/s (an example of a bounded input). Determine whether the system
is stable or unstable.
U(s)

1
s +1

Y(s)

Example 3.2
Obtain the time response of the system shown below for a unit step input
U(s) = 1/s (an example of a bounded input). Determine whether the system
is stable or unstable.
U(s)

1
s 1

Y(s)

Stability of a Closed-loop system


When a closed-loop is designed, the problem of stability may arise if the
controller is not properly designed. A stable open-loop system may become
an unstable closed-loop system.

In some cases, an unstable open-loop

system can be stabilized using a feed-back control system.

Consider a closed-loop system shown below.


u

y
G(s)

H(s)

The transfer function is


y
G
=
u 1 + GH

The equation 1 + GH = 0 is known as the characteristic equation. In


general, the transfer function of a closed loop system can be written as
y N ( s) bm s m + bm 1 s m 1 +L+ b0
, n>m
=
=
u D( s)
s n + an 1 s n 1 +L+ a0

where D(s) = 0 is the characteristic equation. This transfer function can be


written in pole-zero configuration as
y ( s + z1 )( s + z 2 ) L ( s + z m )
=
u ( s + p1 )( s + p 2 ) L ( s + p n )

where the poles are the roots of the denominator of the transfer function and
zeros are the roots of the numerator of the transfer function.

The response of this system to a unit impulse input U(s) = 1 can be obtained
as

The response is bounded if the poles are negative. Stability of the system is
determined by the poles only. Thus, the sufficient condition for stability of a
feedback control system is all poles of the closed loop transfer function must
have a negative real values. Stability region on the s-plane is shown below.
The system is stable if all the poles are located on the left hand side of the
imaginary axis.

Example 3.3
Determine the stability of a system with a characteristic equation
q(s) = s3 + 4s2 + 6s + 4

Example 3.4
For a marginally stable open-loop system shown below, determine the
stability of a closed-loop system if a proportional controller gain Kp = 24 is
used.
m

1
s ( s + 1)( s + 2)

Routh Stability Criterion


The Routh Stability Criterion is a method which can determine the existence
of positive poles. This criterion is sufficient if the designer only wish to
determine the range of control parameter that will ensure closed loop
stability. Consider a closed loop system with the characteristic equation
q ( s) = a n s n + a n 1 s n 1 + L + a 0 = 0

The stability of this system can be tested by constructing the Routh table as
shown below.

This table is filled horizontally and vertically until the remaining elements
are zeros. The characteristic equation has all negative roots if the signs of all
elements in the first column are the same. The number of positive roots is
equal to the number of the signs change.

Example 3.5
Determine the stability of a system with a characteristic equation
q ( s ) = s 4 + 5s 3 + 20s 2 + 40 s + 50

Example 3.6
Determine the stability of a closed-loop system shown below.
y
u

24
3
s + s 2 + 2s
-

Example 3.7
Determine the stability of a system with a characteristic equation
q ( s ) = s 5 + 2s 4 + 2s 3 + 4s 2 + 11s + 10

Example 3.8

K
s( s + 3)( s + 10)

Determine the range of K which ensure the closed loop system to be stable.

The Root Locus Method

The Root Locus Concept


The relative stability and the transient performance of a closed-loop control
system are directly related to the location of the closed-loop roots of the
characteristic equation in the s-plane. It is frequently necessary to adjust one
or more parameters in order to obtain suitable root locations. The root locus
is the path of the roots of the characteristic equation traced out in the splane as a system parameter is changed.

Consider a feedback control system shown below.


u

y
KG(s)

H(s)

The closed-loop transfer function, the open-loop transfer function, and the
characteristic equation can be written as:

It can be seen that the values of the roots of the characteristic equation will
change if the value of the parameter K is changed. When K = 0 the locus
starts at the poles of the open-loop transfer function and the locus ends at the
zeros of the open-loop transfer function when K = .

Magnitude and Angle Criteria


Every point on the locus must satisfy the magnitude and angle criteria and
can be formally written as:

Example 3.9
Draw the locus of the roots of the characteristic equation of the control
system shown below when K varies from 0 to .
y
u

K
s ( s + 2)
-

Example3.10
For a control system shown below, show that the root locus starts at the
poles of the open-loop transfer function when K = 0 and it ends at the zeros
of the open-loop transfer function when K = .
y
u

K
s ( s + 2)
-

Example 3.11
Using the magnitude and angle criteria, verify that s1 = -1 + j is one of the
roots of the characteristic equation of the control system shown below when
K=4
y
u

K
s ( s + 4 s + 6)
2

The Root Locus Procedure

The Root Locus Procedure


1. Locate the poles and zeros of the open-loop transfer function and plot
them using x for poles and o for zeros.
2. The root locus on the real axis always lies in a section of the real axis to
the left of an odd number of poles and zeros.
3. The loci begin at the poles and end at zeros or zeros at infinity, , along
asymptotes.
4. The number of asymptotes is equal to the number of poles minus the
number of zeros, p z. The direction of the asymptotes is define by the
asymptote angle , where
=

(2r + 1)180 0
pz

with r = 0, 1, 2,

5. All asymptotes intersect the real axis at a single point A , often called the
asymptote centroid, defined by
A =

p z
i

pz

where

pi is the values of the poles


zi is the values of the zeros

6. Points of breakaway from or arrival at the real axis may also exist and
can be obtained by rearranging the characteristic equation to isolate the
multiplying factor K in the form of
K = f(s)
On the real axis, the breakaway point happens when K is maximum, i.e.
dK
=0
ds

7. The loci are symmetrical about the real axis. The loci approach or
leaving the real axis at an angle of 90o.
8. The angle of departure, d, form a complex pole is obtained from the
angle criterion

d = 1800 - p + z
where p and z are the angles from other poles and zeros to the pole in
question.
9. The intersection of the locus with the imaginary axis is obtained using the
Routh stability criterion.

Example 3.12
Draw the root locus for a control system with an open-loop transfer function
given as
KGH ( s ) =

K
s ( s + 2)( s + 6)

Determine the number of asymptotes, the asymptote angles, and the


asymptote centroid.

Example 3.13
Draw the root locus for a control system with an open-loop transfer function
given as
KGH ( s ) =

K
( s + 2)( s + 4)

Determine the breakaway point.

Example 3.14
Draw the root locus for a control system with an open-loop transfer function
given as
KGH ( s ) =

K ( s + 2)
( s 2 + 2 s + 4)

Determine the breakaway point.

Example 3.15
Draw the root locus for a control system with an open-loop transfer function
given as
KGH ( s ) =

K ( s + 2)
s ( s 2 + 2 s + 2)

Determine the departure angle from the complex poles.

Example 3.16
Draw the root locus for a control system with an open-loop transfer function
given as
KGH ( s ) =

K
s ( s + 6 s + 25)
2

Determine the intersection of the locus with the imaginary axis.

Interpretation of Root Locus

Interpretation of Root Locus and controller design


When the design of a feedback control system is undertaken, the controller
must be chosen such that the closed-loop system is stable and its transient
response is satisfactory and all specifications are satisfied. For a stable
system, all roots must lie on the left-hand side of the imaginary axis.
Meanwhile, the transient response of the closed-loop system is determined
by the damping ratio, , natural frequency, n, damped natural frequency,

d , and time constant, T. The values of these parameters can be estimated


from the location of the dominant roots from the root locus in the s-plane.

Example 3.17
A control system is represented by a block diagram shown below.
u

1
2
( s + 1)( s + 4 s + 8)

a) Draw the root locus when K increases from zero.


b) It is given that when K = 10, the roots of the characteristic equation are
3 dan 1 j2.24. Determined the damping ratio, natural frequency,
damped natural frequency, and time constant, T for K = 10.

Example 3.18
For a control system shown below, chose the value of the controller K such
that the maximum value of the damping ratio is 0.5 and the minimum value
of the time constant is 1s.
u

K
-

5
s (0.25s + 1)(0.1s + 1)

You might also like