AWS D1.2 Guides

WPSAmerica.
com
AWS D1.2 (Structural Welding Code-Aluminum)
Quick Review on Essential Variables
1-Guide (General)
AWS D1.2, Table 3.1 A change in the mode of metal transfer
for GMAW, a change from AC to DC (GTAW, GMAW) or
vice versa, a change from DCEN to DCEP (GTAW) or vice
versa, a change on shielding gases, M-number, etc. are change
of essential variables and need re-qualification of WPS (by
PQR).
2-Guide (Position)
AWS D1.2, Table 3.1 Vertical Welding: For any pass from
upward to downward or vice versa is essential variable. Also
change from forehand to backhand and vice versa (except as
stated in Table 4.4) are essential variables.
AWS D1.2, Table 3.3 WPS Qualification

CJP and PJP Groove (Plate or Pipe), or
Fillet Weld (Plate or Pipe) Qualification Test:
Position Tested
1G, 1G (Rotated)
2G (CJP)
2G (PJP)
3G (CJP)
3G (PJP)
4G (CJP)
4G (PJP)
5G
6G
1F, 1F (Rotated)
2F, 2F (Rotated)
3F
4F (Plate)
4F (Tubular)
5F
Position Qualified*
F
F, H
H
F, V
V
F, OH
OH
F, V, OH
All Positions
F
F, H
V
All Positions
F, H, OH
All Positions
* Test on plate qualifies for welding pipe or tubing over 24 in

(610 mm) in diameter.
PAGE 1 OF 6
WPSAmerica.com
3-Guide (Thickness/Diameter of Base Metal Range)
AWS D1.2, Table 3.4:
Test on Plate, CJP Groove Welds:
T: Thickness of Test Coupon Welded
T less than 1/8 in. (3 mm):
Qualified Thickness Range: T Min., 2T Max.
T from 1/8 in. (3 mm), to 3/8 in. (10 mm), incl.:
Qualified Thickness Range: 1/8 in. (3 mm) Min., 2T Max.
T over 3/8 in. (10 mm), to less than 1 in. (25 mm):
Qualified Thickness Range: 0.5T Min., 2T Max.
T 1 in. (25 mm) and over:
Qualified Thickness Range: 0.5T Min., Unlimited
AWS D1.2, Table 3.5:

Test on Plate, PJP Groove Welds:
S: Thickness of Test Groove Depth
Groove type same as construction,
Groove Depth Max. 1 in. (25 mm):
Qualified Thickness Range: Unlimited
Fillet Weld WPS Qualification (Qualify all Plate/Pipe
Thickness): Test shall be based on Max. single pass and Min.
multiple pass fillet weld size to be used in construction
(See AWS D1.2, Table 3.6).
PAGE 2 OF 6
WPSAmerica.com
4-Guide (Diameter of Base Metal Range)
AWS D1.2, Table 3.4
Test on Pipe (Tube), CJP Groove Welds:
Tests on Cyclically Loaded Tubular Structures:
A) Job Size Test Pipes:
A.1) Nominal Diam. Less than 24 in. (610 mm):
T less than 1/8 in. (3 mm):
Qualified Thickness Range: T Min., 2T Max.
T from 1/8 in. (3 mm) to 3/8 in. (10 mm), incl.:
T over 3/8 in. (10 mm), but less than 3/4 in. (19 mm):
Qualified Thickness Range: T/2 Min., 2T Max.
T from 3/4 in. (19 mm) and over:
Qualified Nominal Diameter of Pipe (Tube) Size:
Test diameter and over
A.2) Nominal Diam. from 24 in. (610 mm) and over

B) Standard Test Pipes
Test on Pipe (Tube), CJP Groove Welds
Tests on Cyclically Loaded Tubular Structures
(See results for A.2) and B) on the next page):
PAGE 3 OF 6
WPSAmerica.com
AWS D1.2, Table 3.4
Tests on Cyclically Loaded Tubular Structures:
A.2) Nominal Diam. from 24 in. (610 mm) and over:
T from 1/8 in. (3 mm) to 3/8 in. (10 mm), incl.:
Test diameter and over
T over 3/8 in. (10 mm), but less than 3/4 in. (19 mm):
24 in. (610 mm OD) and over
T from 3/4 in. (19 mm) and over:
Qualified Thickness Range: 3/8 in. (10 mm) Min., Unlimited
B) Standard Test Pipes:
2 in. Sch. 80 or 3 in. Sch. 40
Qualified Thickness Range:
1/8 in. (3 mm) Min., 1/2 in. (13 mm) Max.
3/4 in. (19 mm OD) through 4 in. (100 mm OD)
6 in. Sch. 120 or 8 in. Sch. 80
Qualified Thickness Range: 3/8 in. (10 mm) Min., Unlimited
PAGE 4 OF 6
WPSAmerica.com
AWS D1.2, Table 3.4
Tests on Statically Loaded Tubular Structures:
C.1) Wrought material type
[6 thru 8 in. OD; T from 1/8 (3 mm) to 3/8 in. (10 mm) incl.]
1/8 in. (3 mm) Min., 2T Max.
3/4 in. (19 mm) Min., 16 in. (410 mm OD) Max.
C.2) Cast to Wrought or Cast to Cast material type
[3 thru 5 in. OD with T=3/16 in (5 mm)]
1/8 in. (3 mm) Min., 1/2 in. (13 mm) Max.
2 in. (50 mm) Min., 16 in. (410 mm OD) Max.
5-Guide (Base Metal Selection)

AWS D1.2, Table 3.1 A change from one M-number group to
another M-number group or to an alloy that does not have Mnumber is essential variables.
6-Guide (Filler Metal Selection)
AWS D1.2, Table 3.1 A change from one F-number group to
another F-number group or to an alloy that does not have Fnumber is essential variables.
PAGE 5 OF 6
WPSAmerica.com
7-Guide (Joint)
AWS D1.2, Table 3.1: Essential Variables for Joints:
-A change in groove type (e.g., single-V to double-V), except
qualification of any CJP groove weld qualifies for any groove
detail as shown in Annex B1 except square groove joints
-A change in type of groove to a square groove
-A decrease of more than 5 degrees in the nominal groove
angle
-The omission, but not inclusion, of backgouging
-A change from permanent backing to temporary backing or no
backing
PAGE 6 OF 6

AWS D1.2 Guides

Uploaded by

Copyright:

Available Formats

AWS D1.2 Guides

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AWS D1.2 Guides

Uploaded by

Copyright:

Available Formats

WPSAmerica.

AWS D1.2, Table 3.3 WPS Qualification

* Test on plate qualifies for welding pipe or tubing over 24 in

AWS D1.2, Table 3.5:

A.2) Nominal Diam. from 24 in. (610 mm) and over

5-Guide (Base Metal Selection)

You might also like