Paper 4 - Energy Auditor - Set B Answer Key: General Instructions

Paper 4 Energy Auditor Set B Answer key
Regn No: _________________

Name: ___________________
(To be written by the candidates)
5th NATIONAL CERTIFICATION EXAMINATION

FOR
ENERGY AUDITORS November, 2007
PAPER 4: ENERGY PERFORMANCE ASSESSMENT FOR EQUIPMENT AND

UTILITY SYSTEMS
Date: 18.11.2007
Timings: 1400-1600 HRS
Duration: 2 HRS
Max. Marks: 100
General instructions:
o
o
o
o
o
Please check that this question paper contains 6 printed pages

Please check that this question paper contains 16 questions
The question paper is divided into three sections
All questions in all three sections are compulsory
All parts of a question should be answered at one place
Section - I:
SHORT DESCRIPTIVE QUESTIONS
Marks: 10 x 1 = 10
(i) Answer all Ten questions

(ii) Each question carries One mark
(iii) Answer should not exceed 50 words
S-1
While using pitot tubes for airflow measurement in large ducts, series of traverse
readings are recommended. Why?
Velocity of air stream is not uniform across the cross section of the duct. Friction
slows the air moving closes to the wall, so the velocity is greater in the center of the
duct. Therefore, average of velocity measurement readings are required
S-2
In an air conditioning system analysis which one temperature is sufficient to

determine the enthalpy of air?
Wet Bulb Temperature
S-3
Installing the capacitor near motor terminals will increase the design power factor of
the motor - True / False
False
S-4
Between back pressure turbine and condensing turbine which will have more power
generation efficiency?
Condensing turbine
_________________________
Bureau of Energy Efficiency

S-5
The active power consumed by a pure inductive or capacitive load will be zero.
State -True or False.
True
S-6
In a shell and tube heat exchanger, engaged in heat transfer between fouling fluid
and clear fluid, the fouling fluid should be put on shell side or tube side?
Tube side
S-7
What is the power factor for electrical loads having only incandescent lamps?
Unity
S-8
S-9
In the determination of which boiler losses specific heat of superheated steam is

used
Loss due to moisture in air, loss due to hydrogen in fuel,
loss due to moisture in fuel
A centrifugal pump raises water to a height of 12 metre. if the same pump handles
brine with specific gravity of 1.2, to what height the brine will be raised?
12 metres or the same height
S-10
While reducing excess air in a boiler what two parameters should be closely
monitored in the exit flue gases ?
CO, O2
-------- End of Section - I ---------
Section - II:
LONG DESCRIPTIVE QUESTIONS
Marks: 2 x 5 = 10
(i) Answer all Two questions

(ii) Each question carries Five marks
L-1
On the recommendations of energy auditor a company replaced a 15 kW, 6

pole standard motor by a 15 kW, 6 pole energy efficient motor for a
centrifugal fan. The power consumption of energy efficient motor actually
increased, while the grid frequency and voltage remained same. What could
be the reason?
Ans.
In energy efficient motor the slip is less compared to standard motor. Hence
the RPM of energy efficient motor will increase.
Power is proportional to cube of speed for centrifugal fan. Hence the power
consumption will increase
L-2
In a commercial building, an energy auditor recommended to bring down the

cooling tower from the terrace to the ground with a view to save energy in the
_________________________

pump. Details are given in the sketch below. Ignoring the friction losses, will
this measure save energy? Explain with reason
Cooling
Tower
Cooling
Tower
50m
2m
Condenser
Pump
Condenser
Pump
Answer: No, because the pressure differential across the pump

will be same as friction losses are ignored
-------- End of Section - II --------Section - III:
Numerical Questions
Marks: 4 x 20 = 80
(i) Answer all Four questions

(ii) Each question carries Twenty marks
N-1 In a municipality pumping system, water is pumped from the river to an
underground circular sump of 8 metre diametre in the intermediate booster
station. Flow measurements were carried out by level difference in the sump.
Pump takes 10 minutes to fill 1 metre level of circular sump. Pressure gauges
are not available in the pumping system. The discharge pipe is horizontal, 300
mm diametre and 8 km long. Friction factor for the pipe is 0.005. The pump has
a negative suction of 2 metre.
The details of power measurements at motor are:
3 phase voltage: 415 V, line current: 93 A and power factor: 0.89. The efficiency
of the Motor is 0.91.
_________________________
As an energy auditor, work out the following:

a) Flow rate of the pump in m3/hr
b) Power drawn by the motor in kW
c) Total head developed by the pump (ignore friction losses in suction piping)
d) Operating efficiency of the pump
x 82 x 60
4
x 10
302 m3/hr
Flow rate of the pump
Power drawn by the motor
3 x v x I x cos
3 x 0.415 x 93 x 0.89
59.5 kW
Total head
Friction head
Velocity (flow/cross sectional area of
pipe) metre/ second
Friction head
Total head developed by the pump

Operating efficiency of the pump
Hydraulic power
Pump shaft power
Pump efficiency
_________________________
4flv2/2gD
(302/3600)/( x 0.302/4)
1.19 m/s
4 x 0.005 x 1.192 x 8000
2 x 9.81 x 0.3
38.5 metres
38.5 ( -2)
40.5 m
(302/3600) x 40.5 x 9.81
33.3 kW
59.5 x 0.91
54.15 kW
33.3 /54.15
61.5 %
N-2
An energy auditor undertakes the energy audit of a steam system. The

operating data is given as per the schematic diagram given below
Steam
Steam flow rate = 7 TPH
Pressure = 10 kg/cm2 (g)
Temperature = 180 C
Conde nsate
Make-up wa ter
Conde nsate return

Quantity = 4 TPH
Temp. = 94 C
Quantity = 3 TPH
Temp. = 28 C
Boiler
Capacity
10 TPH
Feed Water
Tank
Bare Pipe
Feed
Pu mp
Key data and assumptions are enunciated below

a)
b)
c)
d)
e)
f)
g)
Specific enthalpy of water at 10 kg/cm2 (g) pressure

Specific enthalpy of evaporation/latent heat at 10 kg/cm2 (g)
pressure
Dryness fraction of steam generated
Coal consumption
Net calorific value(NCV) of imported coal
Moisture in coal
Hydrogen in coal
Other parameters as indicated in the above figure
: 186 kCal/kg
: 478 kCal/kg
:
:
:
:
:
0.95
840 kg/ hr
6269 kCal/kg
3.5%
4%
Based on preliminary data assessment as stated above, calculate the following:

(a) Feed water temperature to boiler
(b) Boiler efficiency by direct method on GCV basis
(c) If the condensate return is enhanced to 5 TPH (steam generation of 7 TPH
remaining same) what will be the reduction in coal consumption?
Answer
i. Average Feed water temperature at feed water tank:
(4000x 94 + 3000x 28)
7000
=65.7 C
ii boiler efficiency by direct method on GCV basis
_________________________
GCV of coal = (9 x 0.04 + 0.035) x 584 + 6269 = 6500 kCal / kg

H = Enthalpy of steam: 186 + 0.95x 478 = 640.1 kCal / kg
Efficiency by direct method = [7000 x (640.1- 65.7 ) x 100]/ [6500 x 840]
= 73.64 %
iii reduction in coal consumption if condensate recovery is 5 TPH
Average Feed water temperature at feed water tank:
(5000x 94 + 2000x 28)
7000
=75.14C
coal consumption if the condensate is 5 TPH
= 7000 x (640.1-75.14) / (0.7364 x 6500) = 826 kg/hr
Reduction in coal consumption = (840-826) =14 kg/hr
_________________________

N-3 A waste heat recovery system can be installed in a furnace, which will cost
Rs. 6,50,000/- to install. This system is expected to have a useful life of 6 years.
The salvage value will be Rs. 1,00,000/-. The system will reduce the energy cost
by Rs. 2,00,000/- per year, when it operates at full capacity. However the plant
will be operating at partial capacity for the first 3 years and the annual energy
savings will be at 70% of the energy cost savings at full capacity
(Rs. 1,40,000/-).
The new system will entail a maintenance cost of Rs. 10,000/- per year for the
first 3 years and Rs.12,000 per year for the next 3 years. A major overhaul is
required in the 3rd year, which will cost Rs 1,00,000/a) If discount rate is 9%, calculate the NPV and find out whether this energy
conservation measure is profitable
b) What is the profitability index for the project?
Answer
Year
0.0
1.0
2.0
3.0
4.0
5.0
6.0
Capital
investment,
Rs
-650000
Maintenance,
Rs
Savings,
Rs
Real
Savings,
Rs
10000
10000
110000
12000
12000
12000
NPV
140000
140000
140000
200000
200000
300000
130000
130000
30000
188000
188000
288000
Profitability index
Profitability index
Discount
factor
9%
1
0.917431
0.84168
0.772183
0.708425
0.649931
0.596267
Present
Value, Rs
-650000
119266.1
109418.4
23165.5
133183.9
122187.1
171725
28945.99
NPV/Investment
0.04453
N-4 A process industry invites an energy auditor to suggest ways and means to
reduce the maximum demand on the grid supply. The process industry has a
contract demand of 3940 kVA with Electricity Supply Company. The average
monthly maximum demand is recorded as 3250 kVA at the power factor of 0.9.
The process industry has to pay minimum demand charges of 75% of the
contact demand to the electricity supply company.
After analyzing the electricity bill, the auditor studies the existing PF capacitors
installation at the plant LT substation bus bar and observes the following
connections arrangement.
_________________________
R
Operating line
to line voltage
415 V,
AC,3 Phase
B
N
PF capacitors PF capacitors
PF capacitors
--10 capacitor banks per phase

--Each capacitor bank having 5 units
--Each unit rated for 10 kVAr at 415V
-- Neutral potential is zero volt
The auditor observes that, there are 10 capacitor banks per phase, each bank
comprises of 5 units of PF capacitors and each unit is rated for 10 kVAr at 415 V.
Give your answer on the following:
a)
b)
c)
d)
e)
What is the optimum limit of Power factor improvement, so that plant avoids
paying demand charges over and above the minimum demand charges?
What would be the annual maximum demand charge saving if the existing
power factor is improved to optimum power factor (MD charges @ Rs. 250/- per
kVA per month) ?
What is the additional PF capacitors kVARs requirement to achieve the
desired PF?
What is the present operating capacity of PF capacitors installation at the LT
substation bus bar?
Whether energy auditor would still recommend installation of extra power
factor capacitors in the above situation to achieve the additional PF capacitors
kVARs requirement with the existing capacitors installation at the LT bus bar?
Support your answer with reasons.
Answer
a) Optimum limit of PF improvement:
Desirable MD= 3940x0.75=2955kVA
Desired PF = 3250x0.90/2955= 0.99
b) Annual MD Charge saving = Rs. 250 x 12 x (3250 2955) = Rs. 885000
c) Additional PF capacitors kVARs requirement
= kW( tan cos inv PF1- tan cos inv PF2)
= 3250x0.9( tan cos inv 0.9- tan cos inv 0.99)
= 2925(tan25.84193276-tan 8.109614456)
=2925(0.484322104-0.142492782)
=2925(0.341829821)
= 1000kVAR
_________________________

d) Total capacitor banks
Total capacitor units
Total PF capacitors at the rated ratings
= 10 x 3 = 30
= 30 x 5 = 150
= 150 x 10 = 1500 kVAr at 415 V
As operating voltage of the capacitors in the existing arrangement is 415/ 1.73 = 239.6
V, the actual operating kVAr of the capacitor unit will reduce from 10 kVAr to 10 x
(239.6/415 V)^2 = 3.333 kVAr
Total operating kVAr of the existing installation
= 3.333 x 150 = 500 kVAr
e) Since in the existing arrangement, single phase voltage of 239.6 V is being

supplied, each units capacitors capacity has reduced from 10 kVAr to 3.333 kVAr.
In this case the auditor would recommend modifying the PF connection
arrangement, so that each unit is connected between line to line instead of line to
neutral. In this particular modified connection arrangement 415 Voltage would be
supplied across each unit and each unit would give its rated value of 10 kVAr.
Total kVAr capacity of existing arrangement would improve from 500 kVAr to
1500 kVAr. Hence extra 1000 kVAr capacitors capacity would be available for the
power factor improvements.
R
415 V,
3 Phase
B
N
--10 capacitor banks per phase
--Each capacitor bank having 5 units
--Each unit rated for 10 kVAr at 415V
-- Neutral potential is zero volt
-------- End of Section - III ---------
_________________________

Paper 4 - Energy Auditor - Set B Answer Key: General Instructions

Uploaded by

Copyright:

Available Formats

Paper 4 - Energy Auditor - Set B Answer Key: General Instructions

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Paper 4 - Energy Auditor - Set B Answer Key: General Instructions

Uploaded by

Copyright:

Available Formats

What are the advantages of taking traverse readings across the cross-section of a duct for airflow measurement?

What are the advantages of taking traverse readings across the cross-section of a duct for airflow measurement?

Why is the wet bulb temperature sufficient to determine the enthalpy of air in an air conditioning system analysis?

Why is the wet bulb temperature sufficient to determine the enthalpy of air in an air conditioning system analysis?

Paper 4 Energy Auditor Set B Answer key

Regn No: _________________

5th NATIONAL CERTIFICATION EXAMINATION

PAPER 4: ENERGY PERFORMANCE ASSESSMENT FOR EQUIPMENT AND

Timings: 1400-1600 HRS

Max. Marks: 100

Please check that this question paper contains 6 printed pages

SHORT DESCRIPTIVE QUESTIONS

(i) Answer all Ten questions

In an air conditioning system analysis which one temperature is sufficient to