openUP (March 2008)

The flotation of auriferous pyrite with a mixture of

collectors

A.T. Makanzaa, M.K.G. Vermaaka and J.C. Davidtz a

a

Department of Materials Science and Metallurgical Engineering, University of

Pretoria, Pretoria 0002, South Africa

Abstract
Dithiocarbonates (xanthates) have been the most widely used collectors in sulphide
mineral flotation. More recently, research has resulted in the use of trithiocarbonate
(TTC) collectors. The present study focuses on the effect of mixtures of C12
trithiocarbonate (C12 TTC) and sodium iso-butyl xanthate (SIBX) in the flotation of
auriferous pyrite and the associated gold and uranium from cyanidation tailings.
Improved gold and uranium flotation responses were observed with collector mixtures
than with SIBX alone. Sulphur recoveries were not affected. Mineralogical analysis of
flotation concentrates showed that gold and uranium were also hosted by kerogen. It was
therefore proposed that the improved recoveries could have been mostly due to higher
kerogen recovery rather than synergism in pyrite flotation. This mechanism opens
possibilities into maximising uranium recoveries in auriferous flotation circuits where
low recoveries are common.

Article Outline
1. Introduction
2. Experimental
2.1. Ores and reagents
2.2. Effect of SIBX/C12 TTC mixtures on auriferous pyrite flotation
2.3. Effect of using diluted and aged C12 TTC on the auriferous pyrite flotation

openUP (March 2008)

3. Results and discussion

3.1. Effect of SIBX/C12 TTC mixtures on auriferous pyrite flotation
3.2. Effect of diluted and aged C12 TTC on auriferous pyrite flotation
4. Conclusions
References

1. Introduction
Gold in reclaimed tailings dump material from the Witwatersrand basin in South Africa is
recovered by alkaline cyanide leaching. Occurrences in which metal values are
encapsulated in insoluble minerals like pyrite are not uncommon. Typically, as much as
20% can be associated with the sulphide, which scarcely constitutes more than 4% of the
ore (Botelho De Sousa et al., 1986). This occluded gold is refractory to cyanidation and
has been traditionally recovered by flotation of pyrite from leach residues. The
concentrate produced is calcined at close to 700 C, liberating gold values that are then
leached in cyanide.
Xanthates [dithiocarbonates (DTCs)] have been the collectors of choice for the bulk
flotation of sulphide minerals. Recent advances in collector development have resulted in
the development and application of trithiocarbonate (TTC) collectors. Early bench-scale
flotation research has shown TTCs to be effective in the bulk flotation of sulphides
([Coetzer, 1987], [Coetzer and Davidtz, 1989], [Du Plessis and Davidtz, 1998], [Du
Plessis, 2003] and [Breytenbach et al., 2003]). At present, there is a growing interest in
the flotation behaviour of TTCs when used in combination with other sulphide collectors.
The improved flotation response is believed to be the result of synergism between
collectors, similar to that of dithiocarbamate and dithiocarbonate mixtures reported by
Bradshaw and O'Connor (1994). The work conducted by Du Plessis et al. (2000) also
reported better sulphide flotation response with a mixture of 25% C12 TTC and 75%
SIBX when compared to SIBX alone.
Anglogold Ashanti's No. 2 Gold Plant at Orkney (South Africa) recovers gold from
cyanidation tailings by flotation of pyrite using sodium iso-butyl xanthate (SIBX) as a

openUP (March 2008)

collector. Uranium is recovered as a by-product of the flotation process. Trial runs using
a mixture of SIBX and C12 TTC, first in the laboratory and then at a full plant scale
conducted over a ten-month period showed increases in gold, uranium, and sulphur
recoveries (Davidtz, 2000). This developed interest in the role played by TTC collectors
and prompted further research ([Du Plessis et al., 2000], [Du Plessis, 2003], [Breytenbach
et al., 2003] and [Makanza and Davidtz, 2005]). Some of the areas of interest included
the effect of functional group changes [OCS2 (in DTCs) versus SCS2 (in TTCs)] on
auriferous pyrite flotation response and definition of relevant mechanisms using
electrochemistry and spectroscopy.
Previous studies indicated significant differences between the adsorption mechanisms of
dithiocarbonates (xanthate) and trithiocarbonates (TTC). The xanthate adsorbs via a
charge transfer process and as a result will only adsorb in the presence of an anodic
current. More recent investigations ([Venter and Vermaak, 2007a], [Venter and Vermaak,
2007b] and [Venter and Vermaak, 2007c]) indicated the adsorption of TTC onto the
substrate in reducing conditions it appears that TTC decomposes on the surface and
the decompositional products render the surface hydrophobic. In case of potentials more
positive than equilibrium potential of the TTC monomerdimer couple some oxidation of
the TTC occurs ([Du Plessis, 2003], [Venter and Vermaak, 2007a] and [Venter and
Vermaak, 2007b]).
The present work attempts to quantify the effect of SIBX/TTC collector mixtures on the
flotation of auriferous pyrite from oxidised material such as No. 2 Gold Plant feed.

2. Experimental
2.1. Ores and reagents
The auriferous pyrite ore (80% passing 100 m) used in this study was collected from the
feed to the flotation circuit at No. 2 Gold Plant. Typical chemical and mineralogical
compositions are shown in Table 1 and Table 2. After filtration, approximately 500 kg of
the material was dried at about 60 C for 48 h, screened at 850 m to break any lumps

openUP (March 2008)

and thoroughly mixed. It was first divided into 50 kg batches, and then further divided
into 2 kg samples using the cone and quartering technique.
Table 1.
Typical chemical composition of the bulk ore sample from No. 2 Gold Plant
mass %
Si

Ca

ppm
Fe

Zr

Au Pb

U3O8 Zn

39.62 0.46 3.06 1.03 0.03 0.4 109 140

213

Table 2.
Typical minerals contained in No. 2 Gold Plant feed
Mineral

Chemical formula

Quartz

SiO2

Pyrophyllite

Al2Si4O10(OH)2

Clinochlore

(Mg,Fe)6(Si,Al)4O10(OH)8

Muscovite

(K,Na)(Al,Mg,Fe)2(Si3.1Al0.9)O10(OH)2

Hematite

Fe2O3

Pyrite (cubic) FeS2

Gypsum

CaSO42H2O

Pulp pH was adjusted with reagent grade sulphuric acid and caustic soda. 20 g/t
GEMPOLYM GM4 was used as a depressant, 16 g/t Dowfroth 200 as a frother and 70 g/t
copper sulphate (CuSO45H2O) as an activator. The collectors used in this work were
sodium iso-butyl xanthate, C12 TTC and C12 mercaptan (C12SH). Unless stated otherwise,

openUP (March 2008)

the TTC and mercaptan were dosed from undiluted solutions while the rest of the
reagents were used in the form of 1 wt.% solutions.
2.2. Effect of SIBX/C12 TTC mixtures on auriferous pyrite flotation
The effect of SIBX/C12 TTC mixtures on the flotation of auriferous pyrite was studied
through bulk flotation tests where 20 g/t SIBX was used as a standard. Part of the SIBX
dosage was substituted with C12 TTC on a molar basis (Table 3).
Table 3.
SIBX/C12 TTC mixtures calculated for a 2 kg ore sample
C12 TTC

SIBX

mol% mol 1 wt.% solution (ml) mol% mol 20 wt.% TTC (l)
100

232.6 4.0

0.0

92

214.0 3.7

19

27.9

84

195.3 3.4

16

37

55.8

75

174.4 3.0

25

58

87.2

A 2 kg sample of ore was transferred into a 5 l Denver flotation cell and pulped to
40 wt.% solids using tap water. It was agitated at 1200 rpm for 1 min before any reagents
were added. The pulp was conditioned with copper sulphate for 5 min, followed by the
simultaneous addition of the collectors and 5 min of conditioning. The frother and lastly
the depressant were added, each followed by 1 min of conditioning. Thereafter, the pulp
was aerated and flotation was carried out for 6 min, during which froth was scraped in
15-second intervals at a constant depth. Throughout the experiment, pulp pH was
maintained at 7.2. Froth height was maintained using an automatic level controller
throughout the test.

openUP (March 2008)

Experiments using each collector mixture were repeated in triplicates. The tailings and
bulk concentrates collected from each test were filtered, dried and weighed. Samples
were analysed for sulphur using a 114 Series Leco Sulphur Analyser. Uranium content
was determined with a sequential XRF spectrometer ARL 9400-241 XP+ and gold by fire
assay with lead collection.
2.3. Effect of using diluted and aged C12 TTC on the auriferous pyrite flotation
The effect of using diluted and aged TTC on the flotation of auriferous pyrite was
investigated by means of release curve experiments. The flotation performance of
SIBX/fresh C12 TTC mixture was compared with that of a mixture in which the TTC was
diluted to 1 wt.% and aged for 24 h. A mixture of C12 mercaptan and SIBX was tested for
reference purposes. In all the experiments, SIBX substitutions were done at 8 mol%.
A 4 kg ore sample was transferred into a 10 l Denver flotation cell where it was made up
to a pulp of 40 wt.% solids. After aeration, concentrates were collected at 01, 12, 24,
48, and 820 min intervals. At the end of the each test, concentrates and tailings were
filtered, dried at 60 C and analysed for sulphur, uranium and gold and water recovery
was also determined. All tests were carried out in duplicates. Experimental data were
fitted using empirical first order kinetics outlined by (Cullinan et al., 1999) and (Agar et
al., 1980):
R=Rmax[1ekt].

(1)

Where R (%) is the recovery at time t (min), k (min 1) is the initial rate and Rmax (%) is
the final recovery.

3. Results and discussion

3.1. Effect of SIBX/C12 TTC mixtures on auriferous pyrite flotation
Fig. 1 shows sulphur, gold and uranium recoveries plotted against C12 TTC molar
concentration. Throughout the range of collector compositions, uranium and gold
recoveries followed similar trends. At 8 mol%, uranium recovery was higher than the
standard by 2 percentage points and gold by 4.8. These are equivalent to 7% and 10% of

openUP (March 2008)

the standard respectively, and are significant. At 16 mol% TTC, recoveries were
statistically similar to those observed at 8 mol% and were followed by lower responses at
25 mol%. Sulphur recovery was almost constant throughout the lower response at
25 mol% is insignificant. When long-chain collectors adsorb, very little collector is
needed to saturate all surface active sites. High adsorption density does not necessarily
mean an increase in hydrophobicity. With long-chain collectors, secondary adsorption by
hydrophobic bonding may produce micelle structures with more polar sites exposed and
decreased floatability.

Fig. 1. Response of sulphur, uranium and gold recoveries to C12 TTC concentration in the
collector mixture.
The enhancement of gold and uranium flotation at 8 mol% TTC compared to SIBX alone
could be explained in terms of collector interactions and the nature of minerals that host
the valuable metals. Even though the actual mechanisms are not clearly established
(Bradshaw, 1997) two theories have been proposed in literature to account for flotation
enhancement in applications utilising collector mixtures. Mitrofanov et al. (1985)
attributed better performance to the summation of individual contributions of the
respective collectors. Valdiviezo and Oliveira (1993) however ascribed it to synergism,
the working together of two collectors to yield flotation performances greater than the
sum of the individual reagents. According to Bradshaw (1997) this is due to improved
adsorption characteristics of the mixed collectors on mineral surfaces as compared to
pure collectors. The author highlighted the work conducted by Mellgren (1966) who

openUP (March 2008)

proposed that when one of the collectors adsorbs by chemisorption, it provides sites on
the mineral surface for the subsequent adsorption of the second collector, which is
comprised of more hydrophobic neutral molecules, thereby increasing the overall
hydrophobic properties of the mineral. For the SIBXTTC mixtures being tested in this
present work, since TTC oxidises more readily than SIBX (Du Plessis et al., 2000), it
could initially irreversibly adsorb and the dithiolate of SIBX could then increase the
density of collector packing by physisorption, increasing the hydrophobic state of the
valuable minerals. Surface plasmon resonance (SPR) spectroscopy on gold for
approximately the same alkyl chain length analogue of TTC and DTC, indicated
extremely high values of SPR response obtained for the trithiocarbonate (Groot et al.,
2005). These results indicated a very strong interaction of the TTC with the gold surface.
As a result of this one would expect longer chain TTCs to show a similar strong
interaction compared to the long-chain DTCs.
In Witwatersrand ores, gold refractory to cyanidation and uranium are generally believed
to be hosted by pyrite (Ford, 1993). This means that gold, uranium and sulphur recoveries
should follow fairly similar trends. Fig. 1 shows a significant increase in gold and
uranium recoveries at 8 mol% TTC that is not evident in sulphur recovery. Uranium is
present in the form of oxide minerals uraninite (UO2) and brannerite (U1 xTi2 + xO6)
(Ford, 1993) that are not expected to respond to flotation with thiol collectors by true
flotation entrainment due to changes in the froth structure cannot be ruled out. Since
the presence of liberated gold is unlikely, both metals are probably associated with a
mineral that responded more to SIBX/C12 TTC mixtures than SIBX alone.
In the cyanidation process, milled ores are contacted with activated carbon, which
adsorbs dissolved gold from solution in a process called the carbon-in-leach (CIL)
process. Activated carbon has a tendency of breaking down to sizes small enough to pass
through inter-stage screens placed between leach columns, allowing it to escape into the
tailings stream. The presence of fine particles of loaded activated carbon in cyanidation
tailings such as the material treated in this present work is not unusual. Secondly,
literature has shown that most Witwatersrand ores contain carbonaceous matter known as

openUP (March 2008)

kerogen, which is sometimes associated with gold and uranium ([Simpson and Bowles,
1977], [Anhaeusser et al., 1987], [Robb and Meyer, 1995] and [Parnell, 2001]). Both
activated carbon and kerogen are organic and possess natural hydrophobicity so that they
are likely to influence gold and uranium flotation recoveries.
Back-scattered electron imaging (BEI) and energy dispersive spectroscopy (EDS) were
employed to investigate the presence of carbonaceous matter recovered in the flotation
concentrates. An EDS spectrum (Fig. 3A) of phase A in the electro-micrograph in Fig. 2
shows that it contains 78.95 0.83% by weight uranium and must be uraninite since no
titanium peak could be identified. The occurrence of gold in phase A could not be
determined, most likely because it is below detection limits of the instrument. Phase B
(Fig. 2) contains mostly sulphur and iron (Fig. 3B) and must be pyrite. The darkest
particles (phase C for instance) are high in aluminium and silicon (Fig. 3C) and could be
aluminosilicates and pyrophyllite.

Fig. 2. A back-scattered electron image taken from a concentrate recovered with 8 mol%
C12 TTC.

openUP (March 2008)

Fig. 3. (A), (B) and (C): EDS spectra showing the elemental compositions of the
corresponding phases in Fig. 2.
The presence of lead (15.65 2.90 wt.%) and sulphur (1.32 0.30 wt.%) in the EDS
spectra in Fig. 3(A) suggests the presence of galena and (or) lead in the uraniumcontaining particle. Ford (1993) has reported that uraninite, one of the most important
carriers of uranium in the Witwatersrand, sometimes contains minute specks of up to
20% by mass of galena per grain. The author postulated this to originate from lead
formed by the radioactive decay of uranium. Lead and galena respond very well to
flotation with xanthates ([Tolun and Kitchener, 1963], [Woods, 1971] and [O'Dea et al.,
2001]). Presumably the presence of lead and/ore galena may act as a good substrate for
thiol collector interactions and synergism. In this case the dual function of long-chain
TTCs becomes more interesting. A hydrophobic tail will prefer non-polar surfaces such
as kerogen, as well as a strong sulphide interaction with lead. With regard to gold and
uranium recovery, unique structural features of long-chain TTCs can at least partly
explain improvements in recovery gold not associated with the base metal sulphides is

openUP (March 2008)

expected to show a strong flotation response as indicated by the strong interaction of TTC
with gold surfaces investigated employing SPR spectroscopy (Groot et al., 2005).
The particles labelled A in Fig. 2 are part of a dispersion of fine particles that is
surrounded by a dark matrix. If the borders of the latter are traced, they compound to a
particle. During microprobe analysis of a similar particle (Fig. 4) this matrix remained
unchanged while the surrounding resin was charred by the electron beam of the
instrument. This suggests that it differs from resin used to mount the sample. The EDS
spectra generated during microprobe analysis also showed a significant carbon peak (Fig.
5b) indicating the dark matrix is carbonaceous in nature and could be kerogen. Mounting
the samples in bromine containing resins would have aided the identification of the
carbonaceous matter in these particles.

Fig. 4. A back-scattered electron image taken from the microprobe analysis of

concentrates floated with 8 mol% C12 TTC (A) boundaries of a dark matrix carrying a
fine dispersion of uranium particles, (B) uranium particles, (C) siliceous phase, (D) pyrite
and (E) charring of resin after exposure to electron beam.

openUP (March 2008)

Fig. 5. EDS spectra generated from the microprobe analysis of (a) an iron sulphide and
(b) the dark particle carrying uranium particles found in flotation concentrates.
Another observation from the back-scattered electron image in Fig. 4 is that uranium and
pyrite (see Fig. 5a) co-exist in a single particle. This implies that uranium could at least
be partially recovered with pyrite. Because sulphur recovery was relatively constant
throughout, the higher uranium recovery at 8 mol% TTC was probably due to a
mineralogical association with kerogen and to a lesser extent with pyrite.

openUP (March 2008)

Fig. 6 shows sulphur, gold and uranium concentrate grades plotted versus C12 TTC
concentration. All grades generally decreased as the concentration of TTC was increased.

Fig. 6. Sulphur, uranium and gold grades for different C12 TTC concentrations in the
collector mixture.
In Fig. 7, mass recovery displayed the opposite. Such trends are typical of gangue
flotation. More gangue was recovered as the amount of TTC dosed was increased. This
diluted the concentrates; hence the continuous decrease in grades. A plot of water
recovery versus TTC concentration has also been included in Fig. 7, and it follows a
similar trend with mass recovery. Gangue flotation through entrainment has been known
to be proportional to water recovery ([Engelbrecht and Woodburn, 1975], [Kirjavainen,
1996] and [Savassi et al., 1998]). The correlation between mass and water recoveries
suggests that higher gangue recoveries were more likely to be due to entrainment than
poor selectivity. During experiments, more frothing was observed with SIBX/TTC
mixtures than with SIBX. The behaviour increased with increased TTC concentration.
Gangue collection by long-chain TTC molecules is a possibility. Naturally hydrophobic
gangue minerals such as pyrophyllite and fine particle with activating exchangeable ions
such as cations on muscovite may be collected by true flotation. The long hydrophobic
tail of C12TTC conceivably can attach to the non-polar surface of hydrophobic minerals
and increase entrainment with poorer drainage.

openUP (March 2008)

Fig. 7. Variation of water and mass recovery with C12 TTC concentration in the collector
mixture.
3.2. Effect of diluted and aged C12 TTC on auriferous pyrite flotation
In most flotation processes, it is common practice to dilute collectors prior to their
application. Spectroscopic studies conducted by Du Plessis (2003) and Venter and
Vermaak (2007) have shown that trithiocarbonates decompose to form the respective
mercaptan and carbon bisulphide. The effect of floating pyrite with a diluted (1 wt.%)
and aged C12 TTC (aged for 24 h at a neutral pH) was therefore investigated. Fresh C12
TTC consisting of 20 wt.% solution was used for comparison. A mixture of SIBX and
C12 mercaptan was tested for reference purposes.
The sulphur recovery-grade curves in Fig. 8 show that 8 mol% fresh TTC showed the
best performance. This was followed by the mercaptan mixture, and diluted TTC/SIBX
combination and lastly, the standard. The inability of the thiol (on its own) to act as a
collector was reported by Keller et al. (1994) that found that at low thiol concentrations
(on copper) no significant flotation was possible. Clearly by using a mixture of the thiol
and xanthate good recoveries were realised since the xanthate aids the adsorption of the
thiol. Table 4 contains initial rates and final recovery data. The R2 term shows that all the
data fitted well into first order kinetics described by Eq. (1). Both TTC/SIBX
combinations recorded better sulphur flotation responses than the standard. Between the
TTC mixtures, higher initial rates and final recoveries were obtained with fresh TTC.

openUP (March 2008)

Fig. 8. Sulphur recovery-grade curves for [A] the standard, [B] 8 mol% C12 TTC
diluted and aged for 24 h, [C] 8 mol% C12 mercaptan and [D] 8 mol% fresh C12 TTC.
Table 4.
Sulphur initial rates and final recoveries
Collector composition

R2

k (min 1) Rmax (%)

Standard (20 g/t SIBX)

0.9953 1.03

65.52

8% C12 mercaptan

0.9982 0.82

67.70

8% diluted C12 TTC and aged for 24 h 0.9997 1.42

67.02

8% fresh C12 TTC

69.39

0.9998 1.47

Uranium initial rates and final recoveries are shown in Table 5. Both TTCs (fresh and
aged) had higher initial rates than the standard. The initial rate recorded with fresh TTC
was higher than that for diluted and aged TTC by a factor of 10%. A plot of graderecovery curves in Fig. 9 shows that the final recoveries for the standard and the two TTC
mixtures were almost similar. The fresh TTC/SIBX mixture was more superior because it
recorded the highest initial rate. The mercaptan mixture showed the lowest initial rate and
final recovery.

openUP (March 2008)

Table 5.
Uranium final recoveries and initial rates
Collector composition

R2

k (min 1) Rmax (ppm)

Standard (20 g/t SIBX)

0.9953 0.70

27.47

8% C12 mercaptan

0.9962 0.62

24.30

8% diluted C12 TTC and aged for 24 h 0.9952 0.83

28.40

8% fresh C12 TTC

28.30

0.9966 0.92

Fig. 9. Uranium recovery-grade curves for [A] 8 mol% fresh C12 TTC, [B] 8 mol% C12
mercaptan [C] the standard and [D] 8 mol% C12 TTC diluted and aged for 24 h.
Gold recovery-grade curves are shown in Fig. 10. The respective kinetics data are shown
in Table 6. Initial rates for both SIBX/TTC mixtures differed by 0.03 units and their final
recoveries by 2.4 percentage points. This is equivalent to only 4% and 5% respectively.
The initial rate for the fresh TTC/SIBX mixture was higher than the standard by 0.11
units and considering that this translates to 17% it is significant.

openUP (March 2008)

Fig. 10. Gold recovery-grade curves for [A] the standard, [B] 8 mol% fresh C12 TTC, [C]
8 mol% C12 mercaptan and [D] 8 mol% C12 TTC, diluted and aged for 24 h.
Table 6.
Gold flotation responses for 8 mol% substitution of the standard
Collector composition

R2

k (min 1) Rmax (g/t)

Standard (20 g/t SIBX)

0.9967 0.63

42.4

8% C12 mercaptan

0.9961 0.59

39.4

8% diluted C12 TTC and aged for 24 h 0.9942 0.71

45.0

8% fresh C12 TTC

47.4

0.9956 0.74

Based on the measurement of flotation initial rates and final recoveries, together with
comparison between plotted recovery-grade curves, it is clear that by combining SIBX
and fresh C12 TTC, a better flotation activity is obtained than with SIBX alone. This is in
agreement with earlier plant trials by Davidtz (2000). Previous conclusions have been
that the surface density of collector packing of dixanthogen is promoted by the longchain TTC ([Davidtz, 1999] and [Breytenbach et al., 2003]) implying a synergistic effect.
Furthermore, the addition of TTC at the dosage levels studied does not reduce the
effectiveness of SIBX. The 1 wt.% solution of TTC marginally lost activity when
compared to the fresh TTC solution. This is in good agreement with a microflotation

openUP (March 2008)

study performed by Venter and Vermaak (2007a) indicating that decomposed TTC looses
its effectiveness but still has a higher initial rate compared to xanthate. This is probably
due to the hydrolysis of TTC, forming a mercaptan ([Du Plessis, 2003] and [Venter and
Vermaak, 2007a]). The mercaptan/SIBX reference sample generally showed a distinct
reduction in grade recovery and kinetics. Although there was not much difference
between the fresh and aged TTC, it is likely that the decrease in activity could be more
severe if the concentrations were lower.

4. Conclusions
The effects of replacing mole fractions of SIBX with C12 TTC were investigated. From
bulk flotation tests, it was observed that better gold and uranium flotation performance
was obtained from SIBX/C12 TTC mixtures than with SIBX alone. Sulphur recovery was
comparatively constant throughout all SIBX/TTC mixtures tested. The highest uranium
and gold recoveries were recorded at 8 mol% TTC. Scanning electron and microprobe
investigations showed the presence of a carbonaceous matter called kerogen and is in
agreement with literature. Most of the uranium bearing particles encountered in flotation
concentrates occurred as a fine dispersion in kerogen a small percentage co-exits with
pyrite in a single particle. The better flotation performance was therefore mainly
attributed to enhanced collection of kerogen particles by collector mixtures compared to
SIBX alone. Gold concentrations were below detection limits of the instruments used, but
since literature shows that it is associated with kerogen, the mechanisms described for
uranium be assumed to be common.
Correlation between mass and water recoveries showed that flotation with collector
mixtures was characterised by gangue entrainment. Because kerogen is naturally
hydrophobic, high recoveries of the associated gold and uranium could have been a result
of mass pull but the galena associated with the uranium particles could also enhance the
recovery of the valuables. Measurement of initial rates and final recoveries showed a
marginal decrease in activity of SIBX/TTC mixtures in which TTC has been diluted and
aged compared to fresh TTC.

openUP (March 2008)

References
Agar et al., 1980 G.E. Agar, R. Stratton-Crawley and T.G. Bruce, Optimising the design
of flotation circuits, CIM Bulletin 73 (1980), p. 173.
Anhaeusser et al., 1987 C.R. Anhaeusser, C.E. Feather, W.R. Liebenburg, G. Smits and
J.A. Snegg, Geology and mineralogy of the principal goldfields in South Africa. In: G.G.
Stanley, Editor, The Extractive Metallurgy of Gold in South Africa vol. 1, The South
African Institute of Mining and Metallurgy, Johannesburg (1987), pp. 167.
Botelho De Sousa et al., 1986 A.M.R. Botelho De Sousa, C.T. O'Connor and R.C.
Dunne, The influence of various chemicals, physical and mineralogical factors on the
flotation of gold bearing pyrites, Gold 100: Proceedings of the International Conference
on Gold, Extractive Metallurgy of Gold vol. 2, South African Institute of Mining and
Metallurgy, Johannesburg (1986), pp. 493503.
Bradshaw and O'Connor, 1994 D.J. Bradshaw and C.T. O'Connor, The flotation of pyrite
using mixtures of dithiocarbamates and other thiol collectors, Minerals Engineering 7 (5
6) (1994), pp. 681690.
Bradshaw, 1997 Bradshaw, D. J., 1997, Synergistic effect between thiol collectors used
in the flotation of pyrite. PhD Thesis, University of Cape Town, South Africa.
Breytenbach et al., 2003 W. Breytenbach, M.K.G. Vermaak and J.C. Davidtz, Synergistic
effects among dithiocarbonates (DTCs), dithiophosphate (DTP) and trithiocarbonates
(TTCs) in the flotation of Merensky ores, The Journal of the South African Institute of
Mining and Metallurgy 103 (10) (2003), pp. 667670.
Coetzer, 1987 Coetzer, G., 1987, A quantitative evaluation of sulphydryl collectors on
the selective flotation of a copperleadzinciron ore. Masters Thesis, Potchefstroom
University, South Africa.

openUP (March 2008)

Coetzer and Davidtz, 1989 G. Coetzer and J.C. Davidtz, Sulphydryl collectors in bulk
and selective flotation, Part I. Covalent trithiocarbonate derivatives, The Journal of the
South African Institute of Mining and Metallurgy 89 (10) (1989), pp. 301311.
Cullinan et al., 1999 V.J. Cullinan, S.R. Grano, C.J. Greet, N.W. Johnson and J. Ralston,
Investigating fine galena recovery problems in the lead circuit of Mount Isa Mines
lead/zinc concentrator. Part I: grinding effects, Minerals Engineering 12 (2) (1999), pp.
147163.
Davidtz, 1999 J.C. Davidtz, Quantification of flotation activity by means of excess Gibbs
free energies, Minerals Engineering 12 (10) (1999), pp. 11471161.
Davidtz, 2000 J.C. Davidtz, Optimisation of No. 2 Gold Plant chemical suite, Internal
Report, Anglo Gold (Pty) Ltd, South Africa (2000).
Du Plessis and Davidtz, 1998 R. Du Plessis and J.C. Davidtz, Flotation of copper
sulphide ore, Internal Report, Potchefstroom University, South Africa (1998).
Du Plessis et al., 2000 R. Du Plessis, J.D. Miller and J.C. Davidtz, Preliminary
examination of electrochemical and spectroscopic features of trithiocarbonate collectors
for sulphide mineral flotation, Transactions of the Nonferrous Metallurgy Society of
China 10 (2000), pp. 1218.
Du Plessis, 2003 Du Plessis, R., 2003, The thiocarbonate flotation chemistry of
auriferous pyrite, PhD Thesis, The University of Utah, Utah, USA.
Engelbrecht and Woodburn, 1975 J.A. Engelbrecht and E.T. Woodburn, The effects of
froth height, aeration rate and gas precipitation on flotation, The Journal of the South
African Institute of Mining and Metallurgy (1975), pp. 125132.

openUP (March 2008)

Ford, 1993 M.A. Ford, Uranium in South Africa, The Journal of the South African
Institute of Mining and Metallurgy 2 (1993), pp. 3758.
Groot et al., 2005 D.R. Groot, S.H.M. Harkema and M.K.G. Vermaak, The application of
cyclic voltammetry coupled with surface plasmon resonance measurements to thiolcollector interactions with gold surfaces, The Journal of the South African Institute of
Mining and Metallurgy 105 (2005), pp. 645652.
Keller et al., 1994 H. Keller, P. Simak, W. Screpp and J. Demboski, Surface chemistry of
thiols on copper: an efficient way of producing multilayers, Thin Solid Films 244 (1994),
pp. 799805.
Kirjavainen, 1996 V.M. Kirjavainen, Review and analysis of factors controlling the
mechanical flotation of gangue minerals, International Journal of Mineral Processing 46
(1996), pp. 2134.
Makanza and Davidtz, 2005 A.T. Makanza and J.C. Davidtz, Interim report on the effect
of C12 TTC on the rate grade and recovery of sulphur, gold and uranium at the Anglogold
Ashanti East Plant, Internal Report, Anglogold Ashanti (Pty) Ltd, South Africa (2005).
Mellgren, 1966 O. Mellgren, Heat of adsorption and surface reactions of potassium amyl
xanthate on galena, Transactions of the American Institute of Mining Engineers 235
(1966), pp. 4660.
Mitrofanov et al., 1985 S.I. Mitrofanov, A.S. Kuz'kin and V.N. Filimonov, Theoretical
and practical aspects of using combinations of collectors and frothing agents for sulphide
flotation, Proceedings of 15th Congr. Int. Metall., St. Ettienne, France vol. 2 (1985), pp.
6573.
O'Dea et al., 2001 A.R. O'Dea, K.E. Prince, R.C. Smart and A.R. Gerson, Secondary ion
mass spectrometry investigation of the interaction of xanthate with galena, International
Journal of Mineral Processing 61 (2001), pp. 121143.

openUP (March 2008)

Parnell, 2001 J. Parnell, Paragenesis of mineralisation within fractured pebbles of the

Witwatersrand conglomerates, Mineralium Deposita 36 (2001), pp. 689699.
Robb and Meyer, 1995 L.J. Robb and F.M. Meyer, The Witwatersrand basin, South
Africa: geological framework and mineralisation processes, Ore Geology Reviews 10
(1995), pp. 6794.
Savassi et al., 1998 O.N. Savassi, D.J. Alexander, J.P. Franzidis and E.V. Manlapig, An
empirical model for entrainment in industrial flotation plants, Minerals Engineering 11
(3) (1998), pp. 243256.
Simpson and Bowles, 1977 P.R. Simpson and J.F.W. Bowles, Uranium mineralisation of
the Witwatersrand and dominion reef systems, Philosophical Transactions of the Royal
Society of London 286 (1977), pp. 527548.
Tolun and Kitchener, 1963 R. Tolun and J.A. Kitchener, Electrochemical study of the
galenaxanthateoxygen flotation system, Transactions of the Institute of Mining and
Metallurgy 73 (1963), pp. 313322.
Valdiviezo and Oliviera, 1993 E. Valdiviezo and J.F. Oliviera, Synergism in aqueous
solutions of surfactant mixtures and its effect on the hydrophobicity of mineral surfaces,
Minerals Engineering 6 (1993), pp. 655661.
Venter and Vermaak, 2007a J.A. Venter and M.K.G. Vermaak, Dithiocarbonate and
trithiocarbonate interactions with pyrite, South African Journal of Science 103 (2007), pp.
164168.
Venter and Vermaak, 2007b J.A. Venter and M.K.G. Vermaak, Dithiocarbonate and
trithiocarbonate interactions with copper, Submitted to Minerals Engineering (2007).

openUP (March 2008)

Venter and Vermaak, 2007c J.A. Venter and M.K.G. Vermaak, EIS measurements of
dithiocarbonate and trithiocarbonate interactions with pyrite and copper, Submitted to
Minerals Engineering. (2007).
Woods, 1971 R. Woods, The oxidation of ethyl xanthate on platinum, gold, copper, and
galena electrodes; relation to the mechanism of mineral flotation, Journal of Physical
Chemistry 75 (1971), pp. 354362.

Corresponding authors. Tel.: +27 12 420 4208, +27 84 587 5714; fax: +27 12 362 5304.