ADEC™ - Error List - 2006 - MTU® PDF

ECU7 Software
ADEC Error List

2006-11-16
sorted by No. and ZKP-No.
Dokument
ADEC Error List SFW 2_1_1_1_11_0 SFW 2_2_33_1_1_0.doc
FSW-No:
2_1_1_1_11_0 / 2_2_33_1_1_0
Application:
Universal / All Applications
Generated:
2006-11-16
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
1 von 33
ECU7 Software
No.
ZKP-No.
Name
2.0122.931
HI T-Fuel
2.0122.932
SS T-Fuel
2.0121.931
HI T-Charge Air
2.0121.932
SS T-Charge Air
2.0124.931
HI T-Coolant Intercooler
10
2.0124.932
SS T-Coolant Intercooler
15
2.0100.921
LO P-Lube Oil
16
2.0100.922
SS P-Lube Oil
19
2.0126.931
HI T-Exhaust A
20
2.0126.932
SS T-Exhaust A
21
2.0127.931
HI T-Exhaust B
22
2.0127.932
SS T-Exhaust B
23
2.0152.921
LO Coolant Level
25
2.0154.931
HI P-Diff-Lube Oil
26
2.0154.932
SS P-Diff-Lube Oil
27
2.0151.931
HI Level Leakage Fuel
29
1.8004.206
HI ETC Idle Speed too High
30
2.2510.932
SS Engine Overspeed
31
2.3011.931
HI ETC1 Overspeed
Dokument
Description
Fuel temperature too high (limit 1).
(Alarm Configuration Parameter, for details see PR 2.8008.100)
Charge air temperature too high (limit 1) ==> Check InterCooler
Coolant temperature of InterCooler too high (limit 1).
Pressure of lube oil too low (limit 1).
Exhaust gas temperature (A-side) too high (limit 1).
Exhaust gas temperature (B-side) too high (limit 1).
Coolant level too low (limit 1) ==> Check coolant level in compensation container
Differential pressure of oilfilter too high (limit 1).
Level of leakage fuel too high (limit 1).
Idle Speed of one of the switcheable chargers too high.
Engine Overspeed (limit 2).
Speed of basic charger too high (limit 1).
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
2 von 33
ECU7 Software
No.
ZKP-No.
Name
32
2.3012.932
SS ETC1 Overspeed
36
2.3013.931
HI ETC2 Overspeed
37
2.3013.912
SS ETC2 Overspeed
38
1.8004.205
AL ETC Speed Deviation
39
1.8004.204
AL ETC2 CutIn Failure
44
2.0153.921
LO Coolant Level Intercooler
51
2.0125.931
HI T-Lube Oil
52
2.0125.932
SS T-Lube Oil
57
2.0101.921
LO P-Coolant
58
2.0101.922
SS P-Coolant
59
2.0120.933
SS T-Coolant L3
60
2.0120.934
SS T-Coolant L4
63
2.0106.931
HI P-Crank Case
64
2.0106.932
SS P-Crank Case
65
2.0102.921
LO P-Fuel
66
2.0102.922
SS P-Fuel
67
2.0120.931
HI T-Coolant
68
2.0120.932
SS T-Coolant
81
1.8004.046
AL Rail Leakage
82
2.0104.931
HI P-Fuel (Common Rail)
Dokument
Description
Speed of 1st switcheable charger too high (limit 1).
Speed deviation between basic turbo charger and one of the switcheable chargers.
Switching of charger ETC2 failed.
Coolant level of intercooler too low (limit 1).
Lube oil temperature too high (limit 1).
Lube oil temperature to high (limit 2).
Coolant pressure too low (limit 1) ==> check cooling cycle.
Coolant pressure too low (limit 2) ==> Engine stop or limitation of the injection quantity ==> check cooling cycle
Coolant temperature too high/ too low (limit 3).
Crankcase pressure too high (limit 1).
Fuel supply pressure too low (limit 1) ==> Check filter, fuel on low-pressure side
Fuel supply pressure too low (limit 2) ==> Check filter (low-pressure side)
Coolant temperature too high (limit 1) ==> Check circulation of coolant
Rail pressure gradient too low for Start or too high for Stop
(==> High-pressure system leaks, air in the system)
Rail pressure > setpoint value => DBR reduction, shift of start of injection delayed
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
3 von 33
ECU7 Software
No.
ZKP-No.
83
2.0104.921
85
2.0128.931
86
2.0128.932
89
2.2500.030
90
2.1090.925
91
2.1090.924
92
2.1090.923
93
2.1090.922
94
2.1090.921
95
2.1090.920
102
1.8004.624
104
1.8004.623
118
2.0140.921
119
2.0140.922
120
2.0140.931
121
2.0140.932
122
2.0132.921
176
2.4000.004
Name
Description
(==> interphase transformer sticks or connections of the interphase transformer)
Rail pressure < setpoint value => DBR reduction
LO P-Fuel (Common Rail)
(==> interphase transformer defective or leakage in high-pressure system)
Umblasen' temperature too high (limit 1).
HI T-Umblasen
SS T-Umblasen
Engine is being stalled. The engine speed of the normally operating engine dropped below the limit from
parameter 2.2500.027 Limit Engine Speed Low without any stop request. For safety reason the engine is
SS Engine Speed too Low
stopped when this event occurs.
Idle speed not reached ==> Start abort ==> pay attention to other messages
SS Idle Speed Not Reached
SS Release Speed Not
Acceleration speed not reached ==> Start abort ==> observe other messages
Reached
SS Starter Speed Not
Starter speed not reached ==> Start abort ==> Starter does not turn or turns too slowly
Reached
Preheat temperature too low (limit 2) ==> Coolant temperature for engine start too low ==> Bolting engine start
SS T-Preheat
Preheat temperature too low (limit 1) ==> Coolant temperature for engine start too low
LO T-Preheat
Prelubrication fault.
AL Prelubrication Fault
AL Fuel Cons. Counter
Fuel consumption counter defect.
Defect
Engine Hours Counter defect.
AL Eng Hours Counter Defect
LO ECU Power Supply
Power supply voltage too low (limit 1) ==> Check battery / generator
Voltage
LOLO ECU Power Supply
Voltage
HI ECU Power Supply
Power supply voltage too high (limit 1) ==> Check battery / generator
Voltage
HIHI ECU Power Supply
Voltage
Temperature of electronic too high (limit 1).
HI T-ECU
No (fitting) LifeData-Backup-System is available within a delaytime after ECU-Reset . ==> Backup-system has
AL LifeData not available
no LifeData-function or CAN bus interrupted to Backup-system.
Dokument
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
4 von 33
ECU7 Software
No.
ZKP-No.
Name
177
2.4000.006
AL LifeData restore
incomplete
180
2.0500.680
AL CAN1 Node Lost
181
2.0500.681
AL CAN2 Node Lost
182
2.0500.682
AL CAN Wrong Parameters
183
2.0500.683
AL CAN No PU-Data
184
2.0500.684
AL CAN PU-Data Flash Error
186
2.0500.686
AL CAN1 Bus Off
187
2.0500.687
AL CAN1 Error Passive
188
2.0500.688
AL CAN2 Bus Off
189
2.0500.689
190
2.0500.690
AL EMU Parameter Not

Supported
201
1.8004.570
SD T-Coolant
202
1.8004.572
SD T-Fuel
203
1.8004.571
SD T-Charge Air
205
1.8004.574
SD T-Coolant Intercooler
Dokument
Description
If the ADEC has to restore the LifeData from the backup-system and at least one checksum is wrong after the
upload or the upload is incomplete, then this failure is set.
Connection to a node on CAN bus 1 lost. ==> Check devices connected on CAN
Incorrect CAN parameter values have been entered.
A CAN mode is selected which the communication is initialized aided of the PU data module. However,
required PU data module is not present or is not valid.
==> Check the devices connected by CAN
During attempt to copy a received PU data module to Flash module, a program error occurred. ==> Electronic
service
CAN Controller 1 is in "Bus Off" state => Automatic switchover to CAN2
==>causes e.g. short circuit, massive interference or baud rate incompatibility
CAN Controller 1 has signaled a warning. ==> causes e.g. lack of associated nodes, slight interference or
short-term bus overload.
CAN-Controller 2 is in "Bus Off" state => Automatic switchover to CAN 1 ==>causes e.g. short circuit, massive
interference or baud rate incompatibility.
EMU parameters are not supported. ==> Incompatibility
Coolant temperature-sensor defect. ==> short circuit or cable breakage
==> Check sensor and cable (B6), if necessary replace it.
Fuel temperature-sensor defect. ==> short circuit or cable breakage
Charge air temperature-sensor defect. ==> short circuit or cable breakage
Intercooler coolant temperature-sensor defect. ==> short circuit or cable breakage
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
5 von 33
ECU7 Software
No.
ZKP-No.
Name
206
1.8004.576
SD T-Exhaust A
207
1.8004.577
SD T-Exhaust B
208
1.8004.566
SD P-Charge Air
211
1.8004.563
SD P-Lube Oil
212
1.8004.564
SD P-Coolant
213
1.8004.569
SD P-Coolant Intercooler
214
1.8004.568
SD P-CrankCase
215
1.8004.567
SD P-HD
216
1.8004.575
SD T-Lube Oil
219
1.8004.573
SD T-Intake Air
220
1.8004.584
SD Level Coolant Water
221
1.8004.585
SD P-Diff Lube Oil
222
1.8004.582
SD Level Leakage Fuel
Dokument
Description
Exhaust gas temperature-sensor on A-side defect. ==> short circuit or cable breakage
==> Check sensor and cable (B4.21), if necessary replace it.
Exhaust gas temperature-sensor on B-side defect. ==> short circuit or cable breakage
Charge air pressure-sensor defect. ==> short circuit or cable breakage
Lube oil pressure-sensor defect. ==> short circuit or cable breakage ==> Check sensor and cable (B5), if
necessary replace it.
Collant pressure-sensor defect. ==> short circuit or cable breakage
Intercooler coolant pressure-sensor defect. ==> short circuit or cable breakage
Crankcase pressure-sensor defect. ==> short circuit or cable breakage ==> Check sensor and cable (B50), if
Rail pressure-sensor defect. ==> High-pressure controller emergency operation ==> short circuit or cable
breakage
Lube oil temperature-sensor defect. ==> short circuit or cable breakage
Intake air temperature-sensor defect. ==> short circuit or cable breakage
Sensor for coolant level defect. ==> short circuit or cable breakage
==> Check sensor and cable (F33), if necessary replace it.
Sensor for differential pressure of lube oil defect. ==> short circuit or cable breakage
Sensor for leakage level of fuel defect. ==> short circuit or cable breakage
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
6 von 33
ECU7 Software
No.
ZKP-No.
Name
223
1.8004.583
SD Level Coolant Intercooler
227
1.8004.620
SD P-Lube Oil before Filter
229
1.8004.562
AL Stop Camshaft Sensor

Defect
230
1.8004.498
SD Crankshaft Speed
231
1.8004.499
SD Camshaft Speed
232
1.3011.128
SD Charger 1 Speed
233
1.3011.129
SD Charger 2 Speed
240
1.8004.565
SD P-Fuel
241
1.8004.581
SD T-Umblasen
242
1.8004.622
SD T-Coolant (R)
244
1.8004.621
SD P-Lube Oil (R)
245
2.8006.589
SD ECU Power Supply

Voltage
266
2.8006.586
SD Speed Demand
269
2.8006.588
SD Loadp.Analog filt
Dokument
Description
Sensor for coolant level of intercooler defect. ==> short circuit or cable breakage
Pressure sensor for lube oil before filter defect. ==> short circuit or cable breakage
Sensor of Camshaft defect and sensor of crankshaft defect before. ==> Engine stop
==> Check sensor and cable of B1, if necessary replace it. ==> After Engine restart curing of failure.
Sensor defect on crankshaft. ==> short circuit or cable breakage
==> Check sensor and cable (B13), if necessary replace it. After Engine restart follows curing of failure.
Sensor defect on camshaft. ==> short circuit or cable breakage ==> Check sensor and cable (B1), if necessary
replace it. After Engine restart follows curing of failure.
Speed-sensor of basic charger defect. ==> short circuit or cable breakage
Speed-sensor of switching charger defect. ==> short circuit or cable breakage
Fuel pressure-sensor defect. ==> short circuit or cable breakage
Temperature-sensor of recirculated charge air defect. ==> short circuit or cable breakage
Redundant coolant temperature-sensor defect. ==> short circuit or cable breakage
==> Check sensor and cable, if necessary replace it.
Redundant pressure sensor for lube oil defect. ==> short circuit or cable breakage
Internal ECU error. ==> electronic defect
Analog speed demand defect. ==> short circuit or cable breakage
==> Check setpoint tacho-generator and cable, if necessary replace it.
Filtered analog load pulse signal not available. ==> short circuit or cable breakage
==> Check cable, if necessary replace it.
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
7 von 33
ECU7 Software
No.
ZKP-No.
Name
270
2.8006.590
SD Frequency Input
301
1.8004.500
AL Timing Cylinder A1
302
1.8004.501
303
1.8004.502
304
1.8004.503
305
1.8004.504
306
1.8004.505
307
1.8004.506
308
1.8004.507
309
1.8004.508
310
1.8004.509
311
1.8004.510
AL Timing Cylinder B1
312
1.8004.511
313
1.8004.512
Dokument
Description
Frequency input defect ==> short circuit or cable breakage
Error in timing of injector cylinder A1: timing value too low / high.
==> if very often replace solenoid
Error in timing of injector cylinder B1: timing value too low / high.
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
8 von 33
ECU7 Software
No.
ZKP-No.
Name
314
1.8004.513
315
1.8004.514
316
1.8004.515
317
1.8004.516
318
1.8004.517
319
1.8004.518
320
1.8004.519
321
1.8004.520
AL Wiring Cylinder A1
322
1.8004.521
323
1.8004.522
324
1.8004.523
325
1.8004.524
Dokument
Description
Short circuit in injector cable of cylinder A1. ==> interrupted ignition
==> Remove short circuit of solenoid (plus to ground) (e.g. replace injector)
==> after engine restart curing of failure
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
9 von 33
ECU7 Software
No.
ZKP-No.
Name
326
1.8004.525
327
1.8004.526
328
1.8004.527
329
1.8004.528
330
1.8004.529
331
1.8004.530
AL Wiring Cylinder B1
332
1.8004.531
333
1.8004.532
334
1.8004.533
335
1.8004.534
Dokument
Description
Short circuit in injector cable of cylinder B1. ==> interrupted ignition
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
10 von 33
ECU7 Software
No.
ZKP-No.
Name
336
1.8004.535
337
1.8004.536
338
1.8004.537
339
1.8004.538
340
1.8004.539
341
1.8004.540
AL Open Load Cylinder A1
342
1.8004.541
343
1.8004.542
344
1.8004.543
345
1.8004.544
346
1.8004.545
347
1.8004.546
Dokument
Description
Open load in injector cable of cylinder A1 ==> Interrupted ignition ==> Check cable and solenoid if open load
(e.g. replace injector) ==> after cycle curing of failure
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
11 von 33
ECU7 Software
No.
ZKP-No.
Name
348
1.8004.547
349
1.8004.548
350
1.8004.549
351
1.8004.550
AL Open Load Cylinder B1
352
1.8004.551
353
1.8004.552
354
1.8004.553
355
1.8004.554
356
1.8004.555
357
1.8004.556
358
1.8004.557
359
1.8004.558
360
1.8004.559
361
1.8004.496
AL Power Stage Low
Dokument
Description
Open load in injector cable of cylinder B1 ==> Interrupted ignition ==> Check cable and solenoid if open load
Internal error of electronic (electronic defect possible) ==> Start ITS ==> if electronic o.k. continue to pay
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
12 von 33
ECU7 Software
No.
ZKP-No.
Name
362
1.8004.497
AL Power Stage High
363
1.8004.560
AL Stop Power Stage
365
1.8004.561
AL Stop MV-Wiring Ground
371
1.8004.634
AL Wiring TO 1
372
1.8004.635
AL Wiring TO 2
373
1.8004.636
AL Wiring TO 3
374
1.8004.637
AL Wiring TO 4
381
2.8006.638
AL Wiring TOP 1
382
2.8006.639
AL Wiring TOP 2
383
2.8006.640
AL Wiring TOP 3
384
2.8006.641
AL Wiring TOP 4
390
1.1085.009
AL MCR exceeded
392
2.0129.931
HI T-Coolant (R)
393
2.0129.932
SS T-Coolant (R)
394
2.0112.921
LO P-Lube Oil (R)
Dokument
Description
attention to messages.
If bit "1.1020.021" (Power Stage Failure: Stop Engine) set ==> Engine stop.
Cable line error ==> If bit "1.1020.021" (Power Stage Failure: Stop Engine) set ==> Engine stop
==> possible causes:
1. short circuit of injector line-plus to ground.
2. short circuit of injector line-minus to ground.
Short circuit or open load on transistor output 1 (TO 1).
Short circuit or open load on transistor output plant 1 (TOP 1).
DBR/MCR Function: MCR (Maximum Continuous Rating) is exceeded.
Redundant coolant temperature too high (limit 1) ==> Check circulation of coolant
Redundant pressure of lube oil too low (limit 1).
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
13 von 33
ECU7 Software
No.
ZKP-No.
Name
395
2.0112.922
SS P-Lube Oil (R)
396
1.8004.626
TD T-Coolant
397
1.8004.625
TD P-Lube Oil
400
2.8006.625
AL Open Load Digital Input 1
401
2.8006.626
402
2.8006.627
403
2.8006.628
404
2.8006.629
405
2.8006.630
406
2.8006.631
407
2.8006.632
408
2.8006.633
AL Open Load Emerg. Stop

Input ESI
410
2.0141.921
LO U-PDU
411
2.0141.922
LOLO U-PDU
412
2.0141.931
HI U-PDU
413
2.0141.932
HIHI U-PDU
414
2.0156.931
HI Level Water Fuel Prefilter
415
2.0107.921
LO P-Coolant InterCooler
416
2.0107.922
SS P-Coolant InterCooler
417
1.8004.594
SD Level Water Fuel Prefilter
Dokument
Description
Maximum deviation of coolant temperature.
Maximum deviation of lube oil pressure.
Open Load on digitil input 1. ==> cable breakage or no resistance above switch
Open Load on input for emergency stop. ==> cable breakage or no resistance above switch
Power driver voltage (injectors) too low (limit 1).
Power driver voltage (injectors) too high (limit 1).
Water level of fuel prefilter too high (limit 1) ==> empty fuel prefilter
Coolant pressure of InterCooler too low (limit 1).
Water level-sensor of fuel prefilter defect. ==> short circuit or cable breakage
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
14 von 33
ECU7 Software
No.
ZKP-No.
420
2.0160.921
421
2.0160.922
428
2.0130.921
440
2.0110.921
442
2.0110.931
444
1.8004.578
445
1.8004.580
448
2.0103.931
449
2.0103.932
450
2.8006.592
454
2.7000.011
455
2.8006.650
456
2.8006.651
460
2.8006.652
461
2.8006.653
462
2.8006.654
464
1.8004.589
467
2.0130.922
468
1.8004.579
469
1.8004.590
Name
Description
Input of Aux 1 injured limit 1.
AL L1 Aux 1
AL L2 Aux1
Temperature input of Aux 1 injured limit 1.
AL L1 T-Aux 1
Pressure input of Aux 1 injured limit 1.
AL L1 P-Aux 1
AL L2 P-Aux1
Sensor defect of Injector Power driver unit. ==> Internal error of ECU7. Change ECU7.
SD U-PDU
Ambient air pressure-sensor defect.
SD P-Ambient Air
Pressure of charge air too high (limit 1).
HI P-Charge Air
SS P-Charge Air
Input of Idle/End-Torque defect. ==> short circuit or cable breakage
SD Idle/End-Torque Input [%] ==> Check transmitter and cable, if necessary replace it. After Engine restart follows curing of failure.
Power Reduction is activated.
SS Power Reduction Active
Input of Aux 1 (plant) injured limit 1.
AL L1 Aux1 Plant
AL L2 Aux1 Plant
Exhaust gas temperature of EMU too high (limit 1).
HI T-Exhaust EMU
Exhaust gas temperature of EMU too low (limit 1).
LO T-Exhaust EMU
Coolant temperature of EMU injured limit 1.
HI T-Coolant EMU
Analog input for pressure Aux 1 defect. ==> short circuit or cable breakage
SD P-AUX 1
==> Check transmitter of pressure and cable, if necessary replace it.
AL L2 T-Aux1
Analog input for Temperature Aux 1 defect.
SD T-AUX 1
SD AUX 1
Analog input for Aux 1 defect. ==> short circuit or cable breakage
Dokument
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
15 von 33
ECU7 Software
No.
ZKP-No.
Name
470
1.8004.587
SD T-ECU
471
1.8004.592
SD Coil Current
472
2.8006.593
AL Stop SD
473
1.8004.593
AL Wiring PWM_CM2
474
2.8006.655
AL Wiring FO
475
1.8010.009
AL CR Trigger Engine Stop
476
1.8010.007
AL Crash Rec. Init. Error
478
2.8006.001
AL Comb. Alarm Yel (Plant)
479
2.8006.002
AL Comb. Alarm Red (Plant)
480
2.0291.921
AL Ext. Engine Protection
500
1.4500.900
AL Wiring POM Starter 1
501
1.4500.901
502
1.4500.902
AL Open Load POM

Alternator
503
1.4500.903
AL Battery Not Charging
504
1.4500.904
AL CAN POM Node Lost
Dokument
Description
==> Check transmitter and cable, if necessary replace it.
ECU temperature-sensor defect. ==> short circuit or cable breakage
Coil Current sensor defect. ==> short circuit or cable breakage
Engine stop, because critical channel has sensor defect.
Open load or short circuit on channel PWM_CM2.
Open load or short circuit on frequency output (FO) channel.
Released in case of an engine stop in order to trigger the crash recorder.
Initial error of crash recorder.
Combined Alarm YELLOW (Plant).
Combined Alarm RED (Plant).
External Engine Protection function active.
A wiring fault has been detected in the connection of starter 1 of CPM. This could be an open load, cable break
or short circuit.
==> Check connection between POM and starter.
or short circuit.
An open load on POM's alternator output has been detected.
==> Check connection between POM and alternator.
Battery is not being charged by alternator.
==> Check alternator and connection.
POM is missing on CAN bus.
==> Check connection and POM.
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
16 von 33
ECU7 Software
No.
ZKP-No.
Name
505
1.4500.905
AL New POM Found
506
1.4500.906
AL Low Starter Voltage
507
1.4500.907
AL POM Error
508
1.4500.908
AL Wrong POM-ID
509
1.4500.909
AL Check POM Fuse
510
2.7002.010
AL Override applied
515
2.1090.926
AL Starter Not Engaged
543
2.0555.005
AL Multiple FDH Slaves
544
2.0555.003
AL Configuration Changed
555
2.0555.001
AL Call MTU Field Service
Dokument
Description
A new POM has been found connected to the ECU.
Battery voltage is too low for starting.
==> Check starter battery and cabling.
A general POM error has been detected.
==> Replace POM.
POM sends a different identification number (ID) than expected.
==> Check POM harness.
Reserved.
Override applied.
Starter of CPM / POM could not be engaged. => New starting attempt.
If the number of automatic starting attempts from PR 1.1090.134 Number of Starting Attempts has been
executed, starting procedure is aborted. Check CPM, starter and cabling.
There is more than one device which is configured as Backup for FDH-Functionality.
Gets active in case of changing system configuration e. g. by changing ECU- or SAM-Device.
Remains until undo procedure or data is transfered by a valid maintenance case.
Is cancelled automatically.
Gets active in case of completing a maintenance-case which manipulates Engine-Parameters.
Remains also after switching on-off ECU until a valid release code is entered via Display- and Button-Control of
SAM-Device.
Release Code is available via Internet by a special procedure.
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
17 von 33
ECU7 Software
ZKP-No.
No.
Name
1.1085.009
390
AL MCR exceeded
1.3011.128
232
SD Charger 1 Speed
1.3011.129
233
SD Charger 2 Speed
1.4500.900
500
1.4500.901
501
1.4500.902
502
AL Open Load POM

Alternator
1.4500.903
503
AL Battery Not Charging
1.4500.904
504
AL CAN POM Node Lost
1.4500.905
505
AL New POM Found
1.4500.906
506
AL Low Starter Voltage
1.4500.907
507
AL POM Error
1.4500.908
508
AL Wrong POM-ID
1.4500.909
509
AL Check POM Fuse
1.8004.046
81
AL Rail Leakage
Dokument
Description
DBR/MCR Function: MCR (Maximum Continuous Rating) is exceeded.
Speed-sensor of basic charger defect. ==> short circuit or cable breakage
Speed-sensor of switching charger defect. ==> short circuit or cable breakage
or short circuit.
or short circuit.
An open load on POM's alternator output has been detected.
==> Check connection between POM and alternator.
Battery is not being charged by alternator.
==> Check alternator and connection.
POM is missing on CAN bus.
==> Check connection and POM.
A new POM has been found connected to the ECU.
Battery voltage is too low for starting.
==> Check starter battery and cabling.
A general POM error has been detected.
==> Replace POM.
POM sends a different identification number (ID) than expected.
==> Check POM harness.
Reserved.
Rail pressure gradient too low for Start or too high for Stop
(==> High-pressure system leaks, air in the system)
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
18 von 33
ECU7 Software
ZKP-No.
No.
Name
1.8004.204
39
AL ETC2 CutIn Failure
1.8004.205
38
AL ETC Speed Deviation
1.8004.206
29
HI ETC Idle Speed too High
1.8004.496
361
AL Power Stage Low
1.8004.497
362
AL Power Stage High
1.8004.498
230
SD Crankshaft Speed
1.8004.499
231
SD Camshaft Speed
1.8004.500
301
1.8004.501
302
1.8004.502
303
1.8004.503
304
1.8004.504
305
1.8004.505
306
1.8004.506
307
Dokument
Description
Switching of charger ETC2 failed.
Speed deviation between basic turbo charger and one of the switcheable chargers.
Idle Speed of one of the switcheable chargers too high.
Sensor defect on crankshaft. ==> short circuit or cable breakage
==> Check sensor and cable (B13), if necessary replace it. After Engine restart follows curing of failure.
Sensor defect on camshaft. ==> short circuit or cable breakage ==> Check sensor and cable (B1), if necessary
replace it. After Engine restart follows curing of failure.
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
19 von 33
ECU7 Software
ZKP-No.
No.
Name
1.8004.507
308
1.8004.508
309
1.8004.509
310
1.8004.510
311
1.8004.511
312
1.8004.512
313
1.8004.513
314
1.8004.514
315
1.8004.515
316
1.8004.516
317
1.8004.517
318
1.8004.518
319
1.8004.519
320
Dokument
Description
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
20 von 33
ECU7 Software
ZKP-No.
No.
Name
1.8004.520
321
1.8004.521
322
1.8004.522
323
1.8004.523
324
1.8004.524
325
1.8004.525
326
1.8004.526
327
1.8004.527
328
1.8004.528
329
1.8004.529
330
1.8004.530
331
Dokument
Description
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
21 von 33
ECU7 Software
ZKP-No.
No.
Name
1.8004.531
332
1.8004.532
333
1.8004.533
334
1.8004.534
335
1.8004.535
336
1.8004.536
337
1.8004.537
338
1.8004.538
339
1.8004.539
340
1.8004.540
341
Dokument
Description
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
22 von 33
ECU7 Software
ZKP-No.
No.
Name
1.8004.541
342
1.8004.542
343
1.8004.543
344
1.8004.544
345
1.8004.545
346
1.8004.546
347
1.8004.547
348
1.8004.548
349
1.8004.549
350
1.8004.550
351
1.8004.551
352
1.8004.552
353
1.8004.553
354
1.8004.554
355
Dokument
Description
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
23 von 33
ECU7 Software
ZKP-No.
No.
Name
1.8004.555
356
1.8004.556
357
1.8004.557
358
1.8004.558
359
1.8004.559
360
1.8004.560
363
AL Stop Power Stage
1.8004.561
365
AL Stop MV-Wiring Ground
1.8004.562
229
AL Stop Camshaft Sensor

Defect
1.8004.563
211
SD P-Lube Oil
1.8004.564
212
SD P-Coolant
1.8004.565
240
SD P-Fuel
1.8004.566
208
SD P-Charge Air
Dokument
Description
Cable line error ==> If bit "1.1020.021" (Power Stage Failure: Stop Engine) set ==> Engine stop
==> possible causes:
1. short circuit of injector line-plus to ground.
2. short circuit of injector line-minus to ground.
Sensor of Camshaft defect and sensor of crankshaft defect before. ==> Engine stop
==> Check sensor and cable of B1, if necessary replace it. ==> After Engine restart curing of failure.
Lube oil pressure-sensor defect. ==> short circuit or cable breakage ==> Check sensor and cable (B5), if
Collant pressure-sensor defect. ==> short circuit or cable breakage
Fuel pressure-sensor defect. ==> short circuit or cable breakage
Charge air pressure-sensor defect. ==> short circuit or cable breakage
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
24 von 33
ECU7 Software
ZKP-No.
No.
Name
1.8004.567
215
SD P-HD
1.8004.568
214
SD P-CrankCase
1.8004.569
213
SD P-Coolant Intercooler
1.8004.570
201
SD T-Coolant
1.8004.571
203
SD T-Charge Air
1.8004.572
202
SD T-Fuel
1.8004.573
219
SD T-Intake Air
1.8004.574
205
SD T-Coolant Intercooler
1.8004.575
216
SD T-Lube Oil
1.8004.576
206
SD T-Exhaust A
1.8004.577
207
SD T-Exhaust B
1.8004.578
444
SD U-PDU
1.8004.579
468
SD T-AUX 1
1.8004.580
445
SD P-Ambient Air
Dokument
Description
Rail pressure-sensor defect. ==> High-pressure controller emergency operation ==> short circuit or cable
breakage
Crankcase pressure-sensor defect. ==> short circuit or cable breakage ==> Check sensor and cable (B50), if
Intercooler coolant pressure-sensor defect. ==> short circuit or cable breakage
Coolant temperature-sensor defect. ==> short circuit or cable breakage
Charge air temperature-sensor defect. ==> short circuit or cable breakage
Fuel temperature-sensor defect. ==> short circuit or cable breakage
Intake air temperature-sensor defect. ==> short circuit or cable breakage
Intercooler coolant temperature-sensor defect. ==> short circuit or cable breakage
Lube oil temperature-sensor defect. ==> short circuit or cable breakage
Exhaust gas temperature-sensor on A-side defect. ==> short circuit or cable breakage
Exhaust gas temperature-sensor on B-side defect. ==> short circuit or cable breakage
Sensor defect of Injector Power driver unit. ==> Internal error of ECU7. Change ECU7.
Analog input for Temperature Aux 1 defect.
Ambient air pressure-sensor defect.
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
25 von 33
ECU7 Software
ZKP-No.
No.
Name
1.8004.581
241
SD T-Umblasen
1.8004.582
222
SD Level Leakage Fuel
1.8004.583
223
SD Level Coolant Intercooler
1.8004.584
220
SD Level Coolant Water
1.8004.585
221
SD P-Diff Lube Oil
1.8004.587
470
SD T-ECU
1.8004.589
464
SD P-AUX 1
1.8004.590
469
SD AUX 1
1.8004.592
471
SD Coil Current
1.8004.593
473
AL Wiring PWM_CM2
1.8004.594
417
SD Level Water Fuel Prefilter
1.8004.620
227
SD P-Lube Oil before Filter
1.8004.621
244
SD P-Lube Oil (R)
1.8004.622
242
SD T-Coolant (R)
Dokument
Description
Temperature-sensor of recirculated charge air defect. ==> short circuit or cable breakage
Sensor for leakage level of fuel defect. ==> short circuit or cable breakage
Sensor for coolant level of intercooler defect. ==> short circuit or cable breakage
Sensor for coolant level defect. ==> short circuit or cable breakage
Sensor for differential pressure of lube oil defect. ==> short circuit or cable breakage
ECU temperature-sensor defect. ==> short circuit or cable breakage
Analog input for pressure Aux 1 defect. ==> short circuit or cable breakage
==> Check transmitter of pressure and cable, if necessary replace it.
Analog input for Aux 1 defect. ==> short circuit or cable breakage
==> Check transmitter and cable, if necessary replace it.
Coil Current sensor defect. ==> short circuit or cable breakage
Open load or short circuit on channel PWM_CM2.
Water level-sensor of fuel prefilter defect. ==> short circuit or cable breakage
Pressure sensor for lube oil before filter defect. ==> short circuit or cable breakage
Redundant pressure sensor for lube oil defect. ==> short circuit or cable breakage
Redundant coolant temperature-sensor defect. ==> short circuit or cable breakage
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
26 von 33
ECU7 Software
ZKP-No.
No.
1.8004.623
104
1.8004.624
102
1.8004.625
397
1.8004.626
396
1.8004.634
371
1.8004.635
372
1.8004.636
373
1.8004.637
374
1.8010.007
476
1.8010.009
475
2.0100.921
15
2.0100.922
16
2.0101.921
57
2.0101.922
58
2.0102.921
65
2.0102.922
66
2.0103.931
448
2.0103.932
449
2.0104.921
83
2.0104.931
82
Name
Description
Engine Hours Counter defect.
AL Eng Hours Counter Defect
AL Fuel Cons. Counter
Fuel consumption counter defect.
Defect
Maximum deviation of lube oil pressure.
TD P-Lube Oil
Maximum deviation of coolant temperature.
TD T-Coolant
AL Wiring TO 1
AL Wiring TO 2
AL Wiring TO 3
AL Wiring TO 4
Initial error of crash recorder.
AL Crash Rec. Init. Error
Released in case of an engine stop in order to trigger the crash recorder.
AL CR Trigger Engine Stop
LO P-Lube Oil
SS P-Lube Oil
Coolant pressure too low (limit 1) ==> check cooling cycle.
LO P-Coolant
Coolant pressure too low (limit 2) ==> Engine stop or limitation of the injection quantity ==> check cooling cycle
SS P-Coolant
Fuel supply pressure too low (limit 1) ==> Check filter, fuel on low-pressure side
LO P-Fuel
Fuel supply pressure too low (limit 2) ==> Check filter (low-pressure side)
SS P-Fuel
HI P-Charge Air
SS P-Charge Air
Rail pressure < setpoint value => DBR reduction
LO P-Fuel (Common Rail)
(==> interphase transformer defective or leakage in high-pressure system)
Rail pressure > setpoint value => DBR reduction, shift of start of injection delayed
HI P-Fuel (Common Rail)
(==> interphase transformer sticks or connections of the interphase transformer)
Dokument
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
27 von 33
ECU7 Software
ZKP-No.
No.
Name
2.0106.931
63
HI P-Crank Case
2.0106.932
64
SS P-Crank Case
2.0107.921
415
LO P-Coolant InterCooler
2.0107.922
416
SS P-Coolant InterCooler
2.0110.921
440
AL L1 P-Aux 1
2.0110.931
442
AL L2 P-Aux1
2.0112.921
394
LO P-Lube Oil (R)
2.0112.922
395
SS P-Lube Oil (R)
2.0120.931
67
HI T-Coolant
2.0120.932
68
SS T-Coolant
2.0120.933
59
SS T-Coolant L3
2.0120.934
60
SS T-Coolant L4
2.0121.931
HI T-Charge Air
2.0121.932
SS T-Charge Air
2.0122.931
HI T-Fuel
2.0122.932
SS T-Fuel
2.0124.931
HI T-Coolant Intercooler
2.0124.932
10
SS T-Coolant Intercooler
2.0125.931
51
HI T-Lube Oil
2.0125.932
52
SS T-Lube Oil
Dokument
Description
Lube oil temperature too high (limit 1).
Lube oil temperature to high (limit 2).
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
28 von 33
ECU7 Software
ZKP-No.
No.
Name
2.0126.931
19
HI T-Exhaust A
2.0126.932
20
SS T-Exhaust A
2.0127.931
21
HI T-Exhaust B
2.0127.932
22
SS T-Exhaust B
2.0128.931
85
HI T-Umblasen
2.0128.932
86
SS T-Umblasen
2.0129.931
392
HI T-Coolant (R)
2.0129.932
393
SS T-Coolant (R)
2.0130.921
428
AL L1 T-Aux 1
2.0130.922
467
AL L2 T-Aux1
2.0132.921
122
HI T-ECU
2.0140.921
118
2.0140.922
119
2.0140.931
120
2.0140.932
121
2.0141.921
410
LO U-PDU
2.0141.922
411
LOLO U-PDU
2.0141.931
412
HI U-PDU
2.0141.932
413
HIHI U-PDU
2.0151.931
27
HI Level Leakage Fuel
2.0152.921
23
LO Coolant Level
LO ECU Power Supply

Voltage
LOLO ECU Power Supply
Voltage
HI ECU Power Supply
Voltage
HIHI ECU Power Supply
Voltage
Dokument
Description
Temperature of electronic too high (limit 1).
Level of leakage fuel too high (limit 1).
Coolant level too low (limit 1) ==> Check coolant level in compensation container
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
29 von 33
ECU7 Software
ZKP-No.
No.
Name
2.0153.921
44
LO Coolant Level Intercooler
2.0154.931
25
HI P-Diff-Lube Oil
2.0154.932
26
SS P-Diff-Lube Oil
2.0156.931
414
HI Level Water Fuel Prefilter
2.0160.921
420
AL L1 Aux 1
2.0160.922
421
AL L2 Aux1
2.0291.921
480
AL Ext. Engine Protection
2.0500.680
180
AL CAN1 Node Lost
2.0500.681
181
AL CAN2 Node Lost
2.0500.682
182
AL CAN Wrong Parameters
2.0500.683
183
AL CAN No PU-Data
2.0500.684
184
AL CAN PU-Data Flash Error
2.0500.686
186
AL CAN1 Bus Off
2.0500.687
187
2.0500.688
188
AL CAN2 Bus Off
2.0500.689
189
2.0500.690
190
AL EMU Parameter Not
Dokument
Description
Coolant level of intercooler too low (limit 1).
Water level of fuel prefilter too high (limit 1) ==> empty fuel prefilter
External Engine Protection function active.
Incorrect CAN parameter values have been entered.
A CAN mode is selected which the communication is initialized aided of the PU data module. However,
required PU data module is not present or is not valid.
==> Check the devices connected by CAN
During attempt to copy a received PU data module to Flash module, a program error occurred. ==> Electronic
service
CAN Controller 1 is in "Bus Off" state => Automatic switchover to CAN2
==>causes e.g. short circuit, massive interference or baud rate incompatibility
CAN-Controller 2 is in "Bus Off" state => Automatic switchover to CAN 1 ==>causes e.g. short circuit, massive
interference or baud rate incompatibility.
EMU parameters are not supported. ==> Incompatibility
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
30 von 33
ECU7 Software
ZKP-No.
No.
Name
Supported
2.0555.001
555
AL Call MTU Field Service
2.0555.003
544
AL Configuration Changed
2.0555.005
543
AL Multiple FDH Slaves
2.1090.920
95
AL Prelubrication Fault
2.1090.921
94
LO T-Preheat
2.1090.922
93
SS T-Preheat
2.1090.923
92
2.1090.924
91
2.1090.925
90
SS Idle Speed Not Reached
2.1090.926
515
AL Starter Not Engaged
2.2500.030
89
SS Engine Speed too Low
2.2510.932
30
SS Engine Overspeed
2.3011.931
31
HI ETC1 Overspeed
2.3012.932
32
SS ETC1 Overspeed
2.3013.912
37
SS ETC2 Overspeed
2.3013.931
36
HI ETC2 Overspeed
SS Starter Speed Not

Reached
SS Release Speed Not
Reached
Dokument
Description
Gets active in case of completing a maintenance-case which manipulates Engine-Parameters.
Remains also after switching on-off ECU until a valid release code is entered via Display- and Button-Control of
SAM-Device.
Release Code is available via Internet by a special procedure.
Gets active in case of changing system configuration e. g. by changing ECU- or SAM-Device.
Remains until undo procedure or data is transfered by a valid maintenance case.
Is cancelled automatically.
There is more than one device which is configured as Backup for FDH-Functionality.
Prelubrication fault.
Preheat temperature too low (limit 1) ==> Coolant temperature for engine start too low
Preheat temperature too low (limit 2) ==> Coolant temperature for engine start too low ==> Bolting engine start
Starter speed not reached ==> Start abort ==> Starter does not turn or turns too slowly
Acceleration speed not reached ==> Start abort ==> observe other messages
Idle speed not reached ==> Start abort ==> pay attention to other messages
Starter of CPM / POM could not be engaged. => New starting attempt.
If the number of automatic starting attempts from PR 1.1090.134 Number of Starting Attempts has been
executed, starting procedure is aborted. Check CPM, starter and cabling.
Engine is being stalled. The engine speed of the normally operating engine dropped below the limit from
parameter 2.2500.027 Limit Engine Speed Low without any stop request. For safety reason the engine is
stopped when this event occurs.
Engine Overspeed (limit 2).
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
31 von 33
ECU7 Software
ZKP-No.
No.
2.4000.004
176
2.4000.006
177
2.7000.011
454
2.7002.010
510
2.8006.001
478
2.8006.002
479
2.8006.586
266
2.8006.588
269
2.8006.589
245
2.8006.590
270
2.8006.592
450
2.8006.593
472
2.8006.625
400
2.8006.626
401
2.8006.627
402
2.8006.628
403
2.8006.629
404
2.8006.630
405
Name
Description
No (fitting) LifeData-Backup-System is available within a delaytime after ECU-Reset . ==> Backup-system has
AL LifeData not available
no LifeData-function or CAN bus interrupted to Backup-system.
If the ADEC has to restore the LifeData from the backup-system and at least one checksum is wrong after the
AL LifeData restore
upload or the upload is incomplete, then this failure is set.
incomplete
Power Reduction is activated.
SS Power Reduction Active
Override applied.
AL Override applied
Combined Alarm YELLOW (Plant).
AL Comb. Alarm Yel (Plant)
Combined Alarm RED (Plant).
AL Comb. Alarm Red (Plant)
Analog speed demand defect. ==> short circuit or cable breakage
SD Speed Demand
==> Check setpoint tacho-generator and cable, if necessary replace it.
Filtered analog load pulse signal not available. ==> short circuit or cable breakage
SD Loadp.Analog filt
SD ECU Power Supply
Internal ECU error. ==> electronic defect
Voltage
Frequency input defect ==> short circuit or cable breakage
SD Frequency Input
Input of Idle/End-Torque defect. ==> short circuit or cable breakage
SD Idle/End-Torque Input [%] ==> Check transmitter and cable, if necessary replace it. After Engine restart follows curing of failure.
Engine stop, because critical channel has sensor defect.
AL Stop SD
AL Open Load Digital Input 6 Open Load on digitil input 6. ==> cable breakage or no resistance above switch
Dokument
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
32 von 33
ECU7 Software
ZKP-No.
No.
Name
2.8006.631
406
2.8006.632
407
2.8006.633
408
AL Open Load Emerg. Stop

Input ESI
2.8006.638
381
AL Wiring TOP 1
2.8006.639
382
AL Wiring TOP 2
2.8006.640
383
AL Wiring TOP 3
2.8006.641
384
AL Wiring TOP 4
2.8006.650
455
AL L1 Aux1 Plant
2.8006.651
456
AL L2 Aux1 Plant
2.8006.652
460
HI T-Exhaust EMU
2.8006.653
461
LO T-Exhaust EMU
2.8006.654
462
HI T-Coolant EMU
2.8006.655
474
AL Wiring FO
Dokument
Description
Open Load on input for emergency stop. ==> cable breakage or no resistance above switch
Exhaust gas temperature of EMU too high (limit 1).
Exhaust gas temperature of EMU too low (limit 1).
Coolant temperature of EMU injured limit 1.
Open load or short circuit on frequency output (FO) channel.
Version
1.0
Datum
00.00.2006
Autor
TEE
Seite
33 von 33

ADEC™ - Error List - 2006 - MTU® PDF

Uploaded by

Copyright:

Available Formats

ADEC™ - Error List - 2006 - MTU® PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ADEC™ - Error List - 2006 - MTU® PDF

Uploaded by

Copyright:

Available Formats

What are some of the errors listed in the document?

What are some of the errors listed in the document?

What parameters are used for alarm configuration?

What parameters are used for alarm configuration?

ECU7 Software

ADEC Error List

Universal / All Applications

HI Level Leakage Fuel

HI ETC Idle Speed too High

AL ETC Speed Deviation

AL ETC2 CutIn Failure

LO Coolant Level Intercooler

HI P-Fuel (Common Rail)

AL CAN1 Node Lost

AL CAN2 Node Lost

AL CAN Wrong Parameters

AL CAN PU-Data Flash Error

AL CAN1 Bus Off

AL CAN1 Error Passive

AL CAN2 Bus Off

AL CAN2 Error Passive

AL EMU Parameter Not

SD Level Coolant Water

SD P-Diff Lube Oil

SD Level Leakage Fuel

SD Level Coolant Intercooler

SD P-Lube Oil before Filter

AL Stop Camshaft Sensor

SD P-Lube Oil (R)

SD ECU Power Supply

AL Timing Cylinder A10

AL Timing Cylinder B10

AL Wiring Cylinder A10

AL Wiring Cylinder B10

AL Open Load Cylinder A1

AL Open Load Cylinder A2

AL Open Load Cylinder A3

AL Open Load Cylinder A4

AL Open Load Cylinder A5

AL Open Load Cylinder A6

AL Open Load Cylinder A7

AL Open Load Cylinder A8

AL Open Load Cylinder A9

AL Open Load Cylinder A10

AL Open Load Cylinder B1

AL Open Load Cylinder B2

AL Open Load Cylinder B3

AL Open Load Cylinder B4

AL Open Load Cylinder B5

AL Open Load Cylinder B6

AL Open Load Cylinder B7

AL Open Load Cylinder B8

AL Open Load Cylinder B9

AL Open Load Cylinder B10

AL Power Stage Low

AL Power Stage High

AL Stop Power Stage

AL Stop MV-Wiring Ground

LO P-Lube Oil (R)