Quiz

Course: Advanced Hydraulics
Module 1: Open Channel Flow
Objective type questions

1. Under which of the following conditions steady non-uniform flow in open channels
occurs?
a. When for a constant discharge the liquid depth in the channel varies along its length
b. When a constant discharge flows at the constant depth
c. When a constant discharge flows in a channel laid at a fixed slope
d. When the discharge and the depth both vary along the channel length
2. When the depth of flow changes gradually over a length of the channel, then the flow will
be termed as
a. Rapidly varied flow
b. Critical flow
c. Gradually varied flow
d. Uniform flow
3. Non-uniform flow may caused by
a. The change in width, depth, bed slope etc. of the channel
b. An obstruction, across a channel of uniform width
c. None of the above.
d. Both (a) and (b)
4. The phenomenon occurring in an open channel when a rapidly flowing stream abruptly
changes to slowly flowing stream causing a distinct rise of liquid surface, is
a. Uniform flow
b. Critical discharge
c. Hydraulic jump
d. None of the above
5. The channel whose boundary is not deformable is known as
a.
b.
c.
d.
Rigid channel
Prismatic channel
Mobile channel
Boundary channel
Answers:1 (a)
2 (c)
3(d) 4(c)
Subjective questions:-
5(a)
What is the difference between open channel flow and pipe flow.
Distinguish between:
a. Steady and Uniform flow
b. Unsteady and non-uniform flow
c. Gradually and Spatially varied flow
d. Critical and Super critical flows
e. Prismatic and non-prismatic channel.
Define specific energy. Draw a neat sketch of specific energy curve for a rectangular
channel showing all the details.
Write a short note on velocity distribution in a open channel.
What do you mean by critical flow? Derive the equation for the critical depth in
triangular and rectangular channels.
Find at the discharge in a trapezoidal channel with a bed width of 10m, side slope of 1:1
and depth of flow of 2.0m under uniform flow condition. The bottom slope of 0.0001
and n=0.02. Also, find the Chezys coefficient at this depth. (Ans. 16 cumec, 52.4 m1/2/s)
A rectangular channel has a bed width of 4m, bottom slope of 0.0004 and Manning's n
of 0.02. The normal depth of flow in this channel is 2m. If the channel empties into a
pool at the downstream and the pool elevation of 0.6m higher than canal bed elevation at
the downstream end. Calculate the critical depth of section. (Ans. 0.742 m)
Find the critical depth and critical velocity of the water flowing through a rectangular
channel of width 8m, when discharge is 20cumecs. (Ans 2.9 m/s)
For a given triangular channel, section of side slope 2H: 1V, minimum specific energy is
1.5m. Find the corresponding critical velocity. (Ans. 2.426 m/s)
10
The discharge of water through a rectangular channel of width 6m is 18 cumecs, when

depth of flow of water is 2m. Calculate,
1. Specific energy of flowing water
2. Critical depth and critical velocity
3. Value of minimum specific energy.
(Ans. 2.115m, 0.9716m and 1.457m respectively)
11
A lined channel of trapezoidal section carries a discharge of 10 cumecs, at a depth of
1.2m, with bottom width 2m and side slope of 1.5 Horizontal to 1Vertical. Consider
uniform flow and calculate:
a. The longitudinal slope of the channel.
b. The average shear stress over the wetted perimeter
c. The value of equivalent Darcys f .
d. The Froude number of flow. Assume, Mannings n= 0.010.
(Ans. 1/1351.4, 5.22N/m2, 0.008, 0.776)
12
A rectangular channel 4m wide and bed slope 1 in 5000, conveys a discharge of 5.0
cumecs. The depth of flow at a section is 0.80m. How far upstream will the depth of
flow be 1.0m? Assume N=0.012. (Ans. 461.53m)
13
For a constant specific energy of 1.0 N-m/N, calculate the maximum discharge that may
occur in a rectangular channel, 1.0m wide. (Ans. 2.91cumec)
14
A trapezoidal channel has a bottom width of 6m and side slope of 1:1. The depth of the
flow is 1.5m; bottom slope is 1 in 1000 and discharge of 15cumec flows through it.
Determine the specific energy. Take n=0.015. (Ans. 1.663m).
References:1. Chaudhry, M.H., 1994, Open-Channel Flow, Prentice Hall of India Pvt. Ltd. New
Delhi.
2. Chow, V.T., 1959. Open-channel hydraulics, McGraw Hill, New York.
3. Nagaratnam,S., 1976. Fluid mechanics, Khanna publishers, Delhi
4. Ojha, C.S.P., Berndtsoon, R., and Chandramouli, P.N., 2010. Fluid Mechanics and
Machinery, Oxford University Press, India.
5. Subramanya, K., 1991. Flow in open channels, Tata McGraw-Hill New Delhi.

Quiz

Uploaded by

Copyright:

Available Formats

Quiz

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quiz

Uploaded by

Copyright:

Available Formats

Course: Advanced Hydraulics

Module 1: Open Channel Flow

Objective type questions

Course: Advanced Hydraulics

Module 1: Open Channel Flow

Write a short note on velocity distribution in a open channel.

The discharge of water through a rectangular channel of width 6m is 18 cumecs, when

A lined channel of trapezoidal section carries a discharge of 10 cumecs, at a depth of

Course: Advanced Hydraulics

Module 1: Open Channel Flow

Course: Advanced Hydraulics

Module 1: Open Channel Flow

You might also like