Bearing Properties

HEMANTH KUMAR C
Tribology
CHAPTER 7
Bearing Materials and Wear
1. Introduction
Another factor that can affect the successful operation of
tribological
elements
is
the
solid
materials
used.
Bearing
materials must have special characteristics if the bearings are to

operate successfully. Some desirable characteristics that will be
explored
in
this
chapter
are
compatibility
with
rubbing
counterface materials; embeddability for dirt particles and wear

debris; conformability to enable the bearing to accommodate
misalignment, geometrical errors, and deflection in the structure;
thermal stability; corrosion resistance; and fatigue resistance.
1.1 Properties / Characteristics of Bearing Material
The
selection
of
the
bearing
material
for
particular
application depends on:

The type of bearing (journal, thrust, ball, etc.),
The type of lubricant (grease, oil, water, gas, etc.), and
The environmental conditions (temperature, pressure, etc.).
No single material has been developed that can satisfy all the
requirements of a good bearing material. Therefore, the selection
must be made on the basis of the characteristics considered of
primary importance in the application.
1. Compatibility, 2. Embeddability, 3. Conformability, 4. Corrosion
resistance,
5. Fatigue Resistance, 6. Dimensional and
thermal Stability
Dept of mechanical Engineering
SVIT, Bangalore
HEMANTH KUMAR C
Tribology
1. Compatibility: Although a properly performing hydrodynamic

bearing is one in which the shaft and the bearing are separated
by a lubricant film, there are times during the operation (starting
and stopping) when the shaft and the bearing come into contact.
High spots on the shaft and the bearing rub, localized heating
occurs, the high spots can weld, and the microscopic welds can
fracture. This sequence of events results in scoring damage to
both the shaft and bearing materials. The ability of these material
combinations to resist welding and scoring is a measure of their
compatibility.
2. Embeddability:
In the operation of bearings dirt or other
foreign debris is carried into the bearing clearance by the

lubricant and by the rotation of the shaft. If this dirt cannot be
embedded in the bearing material, scoring damage results. The
ability to embed or absorb this dirt determines the embeddability
characteristic of the bearing material.
3. Conformability: As the term implies, conformability is a
measure of the ability of the bearing material to conform to
misalignment between the shaft and the bearing or to other
geometric inaccuracies produced in manufacturing the parts and
SVIT, Bangalore
HEMANTH KUMAR C
Tribology
deflection in the structure. Usually, bearing materials having a low

modulus of elasticity (low E) are readily conformable.
4. Corrosion resistance: The bearing material should be
resistant to attack by the lubricant or any of the oxidation
products
produced
during
lubricant
degradation
under
the
influence of time and temperature. For example, lubricating oils

without oxidation inhibitors produce organic acids and peroxide
which attack and corrode certain bearing materials. Due to this,
insoluble organic soaps are deposited in the system.
Bearings are subjected to greater corrosion when the volume
of the oil circulating through the bearing is small compared to its
surface area. Materials containing lead, Zinc copper and silver are
the ones mostly subjected to corrosion.
5. Fatigue Resistance: High fatigue resistance is necessary in
applications in which the load changes direction or in which the
load intensity varies cyclically. Fatigue failures appear initially as
cracks in the bearing surface. These cracks propagate throughout
the bearing material, interconnecting with other cracks and
resulting in loose pieces of bearing material. Fatigue strength is
particularly important where cyclic loading is present.
6.
Dimensional
and
thermal
Stability:
The
thermal
characteristics of the bearing material are important with regard

to both heat dissipation and thermal distortion. The thermal
SVIT, Bangalore
HEMANTH KUMAR C
Tribology
conductivity of the bearing material should be high to ensure

maximum
dissipation
of
the
frictional
heat
generated
if
hydrodynamic lubrication conditions cannot be maintained.

7. Relative hardness:
The bearing material should usually be softer than that of the
journal to prevent shaft wear but hard enough to resist adhesive
and abrasive wear of its own surface.
Bearings are easier to replace than shafts (that require
dismantling of the whole engine). If one bearing is worn out only
that bearing needs replacement instead of the whole shaft.
8. Elasticity: should be elastic enough to allow the bearing to
return to original shape upon relief of stresses that may cause
temporary distortion, such as misalignment and overloading.
9. Availability: The material should be readily and sufficiently
available, not only for initial installation but also to facilitate
replacement in the event of bearing failure.
10. Cost: The economic consideration is the ultimate deciding
factor in selecting a bearing material.
SVIT, Bangalore

Bearing Properties

Uploaded by

Copyright:

Available Formats

Bearing Properties

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bearing Properties

Uploaded by

Copyright:

Available Formats

HEMANTH KUMAR C

materials must have special characteristics if the bearings are to

counterface materials; embeddability for dirt particles and wear

application depends on:

5. Fatigue Resistance, 6. Dimensional and

1. Compatibility: Although a properly performing hydrodynamic

In the operation of bearings dirt or other

foreign debris is carried into the bearing clearance by the

Dept of mechanical Engineering

deflection in the structure. Usually, bearing materials having a low

influence of time and temperature. For example, lubricating oils

characteristics of the bearing material are important with regard

Dept of mechanical Engineering

conductivity of the bearing material should be high to ensure

hydrodynamic lubrication conditions cannot be maintained.

Dept of mechanical Engineering

You might also like