Designation: D 2487 06

Standard Practice for

Classification of Soils for Engineering Purposes (Unified

Soil Classification System)1
This standard is issued under the fixed designation D 2487; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.

grande in the early 1940s.2 It became known as the Unified

Soil Classification System when several U.S. Government
Agencies adopted a modified version of the Airfield System in
1952.
1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.7 This practice offers a set of instructions for performing
one or more specific operations. This document cannot replace
education or experience and should be used in conjunction
with professional judgment. Not all aspects of this practice may
be applicable in all circumstances. This ASTM standard is not
intended to represent or replace the standard of care by which
the adequacy of a given professional service must be judged,
nor should this document be applied without consideration of
a projects many unique aspects. The word Standard in the
title of this document means only that the document has been
approved through the ASTM consensus process.

1. Scope*
1.1 This practice describes a system for classifying mineral
and organo-mineral soils for engineering purposes based on
laboratory determination of particle-size characteristics, liquid
limit, and plasticity index and shall be used when precise
classification is required.
NOTE 1Use of this standard will result in a single classification group
symbol and group name except when a soil contains 5 to 12 % fines or
when the plot of the liquid limit and plasticity index values falls into the
crosshatched area of the plasticity chart. In these two cases, a dual symbol
is used, for example, GP-GM, CL-ML. When the laboratory test results
indicate that the soil is close to another soil classification group, the
borderline condition can be indicated with two symbols separated by a
slash. The first symbol should be the one based on this standard, for
example, CL/CH, GM/SM, SC/CL. Borderline symbols are particularly
useful when the liquid limit value of clayey soils is close to 50. These soils
can have expansive characteristics and the use of a borderline symbol
(CL/CH, CH/CL) will alert the user of the assigned classifications of
expansive potential.

1.2 The group symbol portion of this system is based on

laboratory tests performed on the portion of a soil sample
passing the 3-in. (75-mm) sieve (see Specification E 11).
1.3 As a classification system, this standard is limited to
naturally occurring soils.

2. Referenced Documents
2.1 ASTM Standards: 3
C 117 Test Method for Materials Finer than 75-m (No.
200) Sieve in Mineral Aggregates by Washing
C 136 Test Method for Sieve Analysis of Fine and Coarse
Aggregates
C 702 Practice for Reducing Samples of Aggregate to
Testing Size
D 420 Guide to Site Characterization for Engineering Design and Construction Purposes
D 422 Test Method for Particle-Size Analysis of Soils
D 653 Terminology Relating to Soil, Rock, and Contained
Fluids

NOTE 2The group names and symbols used in this test method may
be used as a descriptive system applied to such materials as shale,
claystone, shells, crushed rock, etc. See Appendix X2.

1.4 This standard is for qualitative application only.

NOTE 3When quantitative information is required for detailed designs of important structures, this test method must be supplemented by
laboratory tests or other quantitative data to determine performance
characteristics under expected field conditions.

1.5 This standard is the ASTM version of the Unified Soil

Classification System. The basis for the classification scheme
is the Airfield Classification System developed by A. Casa-

2
Casagrande, A., Classification and Identification of Soils, Transactions,
ASCE, 1948, p. 901.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [email protected]. For Annual Book of ASTM
Standards volume information, refer to the standards Document Summary page on
the ASTM website.

This standard is under the jurisdiction of ASTM Committee D18 on Soil and
Rock and is the direct responsibility of Subcommittee D18.07 on Identification and
Classification of Soils.
Current edition approved May 1, 2006. Published June 2006. Originally
approved in 1966. Last previous edition approved in 2000 as D 2487 00.

*A Summary of Changes section appears at the end of this standard.

Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.

D 2487 06
Finepasses 34-in. (19-mm) sieve and retained on No. 4
(4.75-mm) sieve.
3.1.3 organic claya clay with sufficient organic content to
influence the soil properties. For classification, an organic clay
is a soil that would be classified as a clay except that its liquid
limit value after oven drying is less than 75 % of its liquid limit
value before oven drying.
3.1.4 organic silta silt with sufficient organic content to
influence the soil properties. For classification, an organic silt
is a soil that would be classified as a silt except that its liquid
limit value after oven drying is less than 75 % of its liquid limit
value before oven drying.
3.1.5 peata soil composed of vegetable tissue in various
stages of decomposition usually with an organic odor, a
dark-brown to black color, a spongy consistency, and a texture
ranging from fibrous to amorphous.
3.1.6 sandparticles of rock that will pass a No. 4 (4.75mm) sieve and be retained on a No. 200 (75-m) U.S. standard
sieve with the following subdivisions:
Coarsepasses No. 4 (4.75-mm) sieve and retained on No.
10 (2.00-mm) sieve,
Mediumpasses No. 10 (2.00-mm) sieve and retained on
No. 40 (425-m) sieve, and
Finepasses No. 40 (425-m) sieve and retained on No.
200 (75-m) sieve.
3.1.7 siltsoil passing a No. 200 (75-m) U.S. standard
sieve that is nonplastic or very slightly plastic and that exhibits
little or no strength when air dry. For classification, a silt is a
fine-grained soil, or the fine-grained portion of a soil, with a
plasticity index less than 4 or if the plot of plasticity index
versus liquid limit falls below the A line.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 coeffcient of curvature, Ccthe ratio (D 30 ) 2 /
(D10 3 D60), where D60, D30, and D10 are the particle sizes
corresponding to 60, 30, and 10 % finer on the cumulative
particle-size distribution curve, respectively.
3.2.2 coeffcient of uniformity, Cuthe ratio D60/D10, where
D60 and D10 are the particle diameters corresponding to 60 and
10 % finer on the cumulative particle-size distribution curve,
respectively.

D 1140 Test Method for Amount of Material in Soils Finer

Than the No. 200 (75-m) Sieve
D 2216 Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
D 2217 Practice for Wet Preparation of Soil Samples for
Particle-Size Analysis and Determination of Soil Constants
D 2488 Practice for Description and Identification of Soils
(Visual-Manual Procedure)
D 3740 Practice for Minimum Requirements for Agencies
Engaged in the Testing and/or Inspection of Soil and Rock
as Used in Engineering Design and Construction
D 4083 Practice for Description of Frozen Soils (VisualManual Procedure)
D 4318 Test Methods for Liquid Limit, Plastic Limit, and
Plasticity Index of Soils
D 4427 Classification of Peat Samples by Laboratory Testing
D 6913 Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
E 11 Specification for Wire Cloth and Sieves for Testing
Purposes
3. Terminology
3.1 DefinitionsExcept as listed below, all definitions are
in accordance with Terminology D 653.
NOTE 4For particles retained on a 3-in. (75-mm) U.S. standard sieve,
the following definitions are suggested:
Cobblesparticles of rock that will pass a 12-in. (300-mm) square
opening and be retained on a 3-in. (75-mm) U.S. standard sieve, and
Bouldersparticles of rock that will not pass a 12-in. (300-mm) square
opening.

3.1.1 claysoil passing a No. 200 (75-m) U.S. standard

sieve that can be made to exhibit plasticity (putty-like properties) within a range of water contents and that exhibits
considerable strength when air dry. For classification, a clay is
a fine-grained soil, or the fine-grained portion of a soil, with a
plasticity index equal to or greater than 4, and the plot of
plasticity index versus liquid limit falls on or above the A
line.
3.1.2 gravelparticles of rock that will pass a 3-in. (75mm) sieve and be retained on a No. 4 (4.75-mm) U.S. standard
sieve with the following subdivisions:
Coarsepasses 3-in. (75-mm) sieve and retained on 34-in.
(19-mm) sieve, and

4. Summary
4.1 As illustrated in Table 1, this classification system
identifies three major soil divisions: coarse-grained soils,
fine-grained soils, and highly organic soils. These three divisions are further subdivided into a total of 15 basic soil groups.

TABLE 1 Soil Classification Chart

Criteria for Assigning Group Symbols and Group Names Using Laboratory TestsA
COARSE-GRAINED
Gravels
Clean Gravels
SOILS
More than 50 %
More than 50 % of
Less than 5 % finesE
retained on No.
coarse fraction
200 sieve
retained on No. 4
sieve
Gravels with Fines

Cu $ 4 and
1 # Cc # 3C
Cu < 4 and/or
1 > Cc > 3C

Fines classify as ML
or MH

Soil Classification
Group Symbol
Group NameB
GW
Well-graded gravelD
GP

Poorly graded gravelD

GM

Silty gravelD,F,G

D 2487 06
TABLE 1

Continued

Criteria for Assigning Group Symbols and Group Names Using Laboratory TestsA
More than 12 % finesE
Fines classify as CL or
CH
Sands
Clean Sands
Cu $ 6 and
1 # Cc # 3C
50 % or more of
Less than 5 % finesI
Cu < 6 and/or
coarse
1 > Cc > 3C
fraction passes No. 4
Sands with Fines
Fines classify as ML
sieve
or MH
More than 12 % finesI
Fines classify as CL or
CH
FINE-GRAINED
Silts and Clays
inorganic
PI > 7 and plots on or
SOILS
above A lineJ
50 % or more passes
Liquid limit less than
PI < 4 or plots below
the No.
50
A lineJ
200 seive
organic
Liquid limit oven
dried> < 0.75
Liquid limit not dried
Silts and Clays
inorganic
PI plots on or above
A line
Liquid limit 50 or more
PI plots below A line
organic
Liquid limit oven
dried < 0.75
Liquid limit not dried
HIGHLY ORGANIC
Primarily organic matter, dark in color, and organic odor
SOILS

Soil Classification
Group Symbol
Group NameB
,urule;1>GC
Clayey gravelD,F,G
SW

Well-graded sandH

SP

Poorly graded sandH

SM

Silty sandF,G,H

SC

Clayey sandF,G,H

CL

Lean clayK,L,M

ML

SiltK,L,M

OL

Organic clayK,L,M,N

OL
CH

Organic siltK,L,M,O
Fat clayK,L,M

MH
OH

Elastic siltK,L,M
Organic clayK,L,M,P

PT

Organic siltK,L,M,Q
Peat

Based on the material passing the 3-in. (75-mm) sieve.

If field sample contained cobbles or boulders, or both, add with cobbles or boulders, or both to group name.
C
Cu = D60/D10 Cc 5 ~D30!2 D10 3 D60
D
If soil contains $15 % sand, add with sand to group name.
E
Gravels with 5 to 12 % fines require dual symbols:
GW-GM well-graded gravel with silt
GW-GC well-graded gravel with clay
GP-GM poorly graded gravel with silt
GP-GC poorly graded gravel with clay
F
If fines classify as CL-ML, use dual symbol GC-GM, or SC-SM.
G
If fines are organic, add with organic fines to group name.
H
If soil contains $15 % gravel, add with gravel to group name.
I
Sands with 5 to 12 % fines require dual symbols:
SW-SM well-graded sand with silt
SW-SC well-graded sand with clay
SP-SM poorly graded sand with silt
SP-SC poorly graded sand with clay
J
If Atterberg limits plot in hatched area, soil is a CL-ML, silty clay.
K
If soil contains 15 to 29 % plus No. 200, add with sand or with gravel, whichever is predominant.
L
If soil contains $30 % plus No. 200, predominantly sand, add sand to group name.
M
If soil contains $30 % plus No. 200, predominantly gravel, add gravelly to group name.
N
PI $ 4 and plots on or above A line.
O
PI < 4 or plots below A line.
P
PI plots on or above A line.
Q
PI plots below A line.
B

5.3 The various groupings of this classification system have

been devised to correlate in a general way with the engineering
behavior of soils. This standard provides a useful first step in
any field or laboratory investigation for geotechnical engineering purposes.
5.4 This standard may also be used as an aid in training
personnel in the use of Practice D 2488.
5.5 This standard may be used in combination with Practice
D 4083 when working with frozen soils.

4.2 Based on the results of visual observations and prescribed laboratory tests, a soil is catalogued according to the
basic soil groups, assigned a group symbol(s) and name, and
thereby classified. The flow charts, Fig. 1 for fine-grained soils,
and Fig. 3 for coarse-grained soils, can be used to assign the
appropriate group symbol(s) and name.
5. Significance and Use
5.1 This standard classifies soils from any geographic location into categories representing the results of prescribed
laboratory tests to determine the particle-size characteristics,
the liquid limit, and the plasticity index.
5.2 The assigning of a group name and symbol(s) along
with the descriptive information required in Practice D 2488
can be used to describe a soil to aid in the evaluation of its
significant properties for engineering use.

NOTE 5Notwithstanding the statements on precision and bias contained in this standard: The precision of this test method is dependent on
the competence of the personnel performing it and the suitability of the
equipment and facilities used. Agencies that meet the criteria of Practice
D 3740 are generally considered capable of competent and objective
testing. Users of this test method are cautioned that compliance with
Practice D 3740 does not in itself assure reliable testing. Reliable testing

D 2487 06

FIG. 1

FIG. 2

Flow Chart for Classifying Fine-Grained Soil (50 % or More Passes No. 200 Sieve)

Flow Chart for Classifying Organic Fine-Grained Soil (50 % or More Passes No. 200 Sieve)

D 2487 06

FIG. 3

Flow Chart for Classifying Coarse-Grained Soils (More Than 50 % Retained on No. 200 Sieve)

7.3 If the field sample or test specimen is smaller than the

minimum recommended amount, the report shall include an
appropriate remark.

depends on several factors; Practice D 3740 provides a means for

evaluating some of those factors.

6. Apparatus
6.1 In addition to the apparatus that may be required for
obtaining and preparing the samples and conducting the
prescribed laboratory tests, a plasticity chart, similar to Fig. 4,
and a cumulative particle-size distribution curve, similar to Fig.
5, are required.
NOTE 6The U line shown on Fig. 4 has been empirically determined to be the approximate upper limit for natural soils. It is a good
check against erroneous data, and any test results that plot above or to the
left of it should be verified.

8. Classification of Peat
8.1 A sample composed primarily of vegetable tissue in
various stages of decomposition and has a fibrous to amorphous texture, a dark-brown to black color, and an organic odor
should be designated as a highly organic soil and shall be
classified as peat, PT, and not subjected to the classification
procedures described hereafter.
8.2 If desired, classification of type of peat can be performed in accordance with Classification D 4427.

7. Sampling
7.1 Samples shall be obtained and identified in accordance
with a method or methods, recommended in Guide D 420 or by
other accepted procedures.
7.2 Test Methods D 6913 provides guidance on selecting
size of specimen. Two test methods are provided in this
standard. The methods differ in the significant digits recorded
and the size of the specimen (mass) required. The method to be
used may be specified by the requesting authority; otherwise
Method A shall be performed. Whenever possible, the field
samples should have weights two to four times larger than
shown.

9. Preparation for Classification

9.1 Before a soil can be classified according to this standard,
generally the particle-size distribution of the minus 3-in.
(75-mm) material and the plasticity characteristics of the minus
No. 40 (425-m) sieve material must be determined. See 9.8
for the specific required tests.
9.2 The preparation of the soil specimen(s) and the testing
for particle-size distribution and liquid limit and plasticity
index shall be in accordance with accepted standard procedures. Two procedures for preparation of the soil specimens for
testing for soil classification purposes are given in Appendixes
X3 and X4. Appendix X3 describes the wet preparation method
5

D 2487 06

FIG. 4

FIG. 5

Plasticity Chart

Cumulative Particle-Size Plot

D 2487 06
11. Procedure for Classification of Fine-Grained Soils
(50 % or more by dry weight passing the No. 200 (75m) sieve)
11.1 The soil is an inorganic clay if the position of the
plasticity index versus liquid limit plot, Fig. 4, falls on or above
the A line, the plasticity index is greater than 4, and the
presence of organic matter does not influence the liquid limit as
determined in 11.3.2.

and is the preferred method for cohesive soils that have never
dried out and for organic soils.
9.3 When reporting soil classifications determined by this
standard, the preparation and test procedures used shall be
reported or referenced.
9.4 Although the test procedure used in determining the
particle-size distribution or other considerations may require a
hydrometer analysis of the material, a hydrometer analysis is
not necessary for soil classification.
9.5 The percentage (by dry weight) of any plus 3-in.
(75-mm) material must be determined and reported as auxiliary
information.
9.6 The maximum particle size shall be determined (measured or estimated) and reported as auxiliary information.
9.7 When the cumulative particle-size distribution is required, a set of sieves shall be used which include the
following sizes (with the largest size commensurate with the
maximum particle size) with other sieve sizes as needed or
required to define the particle-size distribution:

NOTE 7The plasticity index and liquid limit are determined on the
minus No. 40 (425 m) sieve material.

11.1.1 Classify the soil as a lean clay, CL, if the liquid limit
is less than 50. See area identified as CL on Fig. 4.
11.1.2 Classify the soil as a fat clay, CH, if the liquid limit
is 50 or greater. See area identified as CH on Fig. 4.
NOTE 8In cases where the liquid limit exceeds 110 or the plasticity
index exceeds 60, the plasticity chart may be expanded by maintaining the
same scale on both axes and extending the A line at the indicated slope.

11.1.3 Classify the soil as a silty clay, CL-ML, if the

position of the plasticity index versus liquid limit plot falls on
or above the A line and the plasticity index is in the range of
4 to 7. See area identified as CL-ML on Fig. 4.
11.2 The soil is an inorganic silt if the position of the
plasticity index versus liquid limit plot, Fig. 4, falls below the
A line or the plasticity index is less than 4, and presence of
organic matter does not influence the liquid limit as determined
in 11.3.2.
11.2.1 Classify the soil as a silt, ML, if the liquid limit is
less than 50. See area identified as ML on Fig. 4.
11.2.2 Classify the soil as an elastic silt, MH, if the liquid
limit is 50 or greater. See area identified as MH on Fig. 4.
11.3 The soil is an organic silt or clay if organic matter is
present in sufficient amounts to influence the liquid limit as
determined in 11.3.2.
11.3.1 If the soil has a dark color and an organic odor when
moist and warm, a second liquid limit test shall be performed
on a test specimen which has been oven dried at 110 6 5C to
a constant weight, typically over night.
11.3.2 The soil is an organic silt or organic clay if the liquid
limit after oven drying is less than 75 % of the liquid limit of
the original specimen determined before oven drying (see
Procedure B of Practice D 2217).
11.3.3 Classify the soil as an organic silt or organic clay,
OL, if the liquid limit (not oven dried) is less than 50 %.
Classify the soil as an organic silt, OL, if the plasticity index
is less than 4, or the position of the plasticity index versus
liquid limit plot falls below the A line. Classify the soil as an
organic clay, OL, if the plasticity index is 4 or greater and the
position of the plasticity index versus liquid limit plot falls on
or above the A line. See area identified as OL (or CL-ML) on
Fig. 4.
11.3.4 Classify the soil as an organic clay or organic silt,
OH, if the liquid limit (not oven dried) is 50 or greater. Classify
the soil as an organic silt, OH, if the position of the plasticity
index versus liquid limit plot falls below the A line. Classify
the soil as an organic clay, OH, if the position of the plasticity
index versus liquid-limit plot falls on or above the A line.
See area identified as OH on Fig. 4.

3-in. (75-mm)
34-in. (19.0-mm)
No. 4 (4.75-mm)
No. 10 (2.00-mm)
No. 40 (425-m)
No. 200 (75-m)

9.8 The tests required to be performed in preparation for

classification are as follows:
9.8.1 For soils estimated to contain less than 5 % fines, a
plot of the cumulative particle-size distribution curve of the
fraction coarser than the No. 200 (75-m) sieve is required. A
semi-log plot of percent passing versus partical-size or sieve
size/sieve number is plotted as shown in Fig. 5.
9.8.2 For soils estimated to contain 5 to 15 % fines, a
cumulative particle-size distribution curve, as described in
9.8.1, is required, and the liquid limit and plasticity index are
required.
9.8.2.1 If sufficient material is not available to determine the
liquid limit and plasticity index, the fines should be estimated
to be either silty or clayey using the procedures described in
Practice D 2488 and so noted in the report.
9.8.3 For soils estimated to contain 15 % or more fines, a
determination of the percent fines, percent sand, and percent
gravel is required, and the liquid limit and plasticity index are
required. For soils estimated to contain 90 % fines or more, the
percent fines, percent sand, and percent gravel may be estimated using the procedures described in Practice D 2488 and
so noted in the report.
10. Preliminary Classification Procedure
10.1 Class the soil as fine-grained if 50 % or more by dry
weight of the test specimen passes the No. 200 (75-m) sieve
and follow Section 3.1.2.
10.2 Class the soil as coarse-grained if more than 50 % by
dry weight of the test specimen is retained on the No. 200
(75-m) sieve and follow Section 12.
7

D 2487 06
12.4.2 Classify the soil as a silty gravel, GM, or silty sand,
SM, if the fines are silty, that is, the position of the plasticity
index versus liquid limit plot, Fig. 4, falls below the A line
or the plasticity index is less than 4.
12.4.3 If the fines plot as a silty clay, CL-ML, classify the
soil as a silty, clayey gravel, GC-GM, if it is a gravel or a silty,
clayey sand, SC-SM, if it is a sand.
12.5 If 5 to 12 % of the test specimen passes the No. 200
(75-m) sieve, give the soil a dual classification using two
group symbols.
12.5.1 The first group symbol shall correspond to that for a
gravel or sand having less than 5 % fines (GW, GP, SW, SP),
and the second symbol shall correspond to a gravel or sand
having more than 12 % fines (GC, GM, SC, SM).
12.5.2 The group name shall correspond to the first group
symbol plus with clay or with silt to indicate the plasticity
characteristics of the fines. For example, well-graded gravel
with clay, GW-GC; poorly graded sand with silt, SP-SM (See
9.8.2.1 if insufficient material available for testing).

11.4 If less than 30 % but 15 % or more of the test specimen

is retained on the No. 200 (75-m) sieve, the words with
sand or with gravel (whichever is predominant) shall be
added to the group name. For example, lean clay with sand,
CL; silt with gravel, ML. If the percent of sand is equal to the
percent of gravel, use with sand.
11.5 If 30 % or more of the test specimen is retained on the
No. 200 (75-m) sieve, the words sandy or gravelly shall
be added to the group name. Add the word sandy if 30 % or
more of the test specimen is retained on the No. 200 (75-m)
sieve and the coarse-grained portion is predominantly sand.
Add the word gravelly if 30 % or more of the test specimen
is retained on the No. 200 (75-m) sieve and the coarse-grained
portion is predominantly gravel. For example, sandy lean clay,
CL; gravelly fat clay, CH; sandy silt, ML. If the percent of sand
is equal to the percent of gravel, use sandy.
12. Procedure for Classification of Coarse-Grained Soils
(more than 50 % retained on the No. 200 (75-m) sieve)
12.1 Class the soil as gravel if more than 50 % of the coarse
fraction [plus No. 200 (75-m) sieve] is retained on the No. 4
(4.75-mm) sieve.
12.2 Class the soil as sand if 50 % or more of the coarse
fraction [plus No. 200 (75-m) sieve] passes the No. 4
(4.75-mm) sieve.
12.3 If 12 % or less of the test specimen passes the No. 200
(75-m) sieve, plot the cumulative particle-size distribution,
Fig. 5, and compute the coefficient of uniformity, Cu, and
coefficient of curvature, Cc, as given in Eqs 1 and 2.
Cu5D60/D10
2

Cc5~D30! /~D103D60!

NOTE 10If the fines plot as a silty clay, CL-ML, the second group
symbol should be either GC or SC. For example, a poorly graded sand
with 10 % fines, a liquid limit of 20, and a plasticity index of 6 would be
classified as a poorly graded sand with silty clay, SP-SC.

12.6 If the specimen is predominantly sand or gravel but

contains 15 % or more of the other coarse-grained constituent,
the words with gravel or with sand shall be added to the
group name. For example, poorly graded gravel with sand,
clayey sand with gravel.
12.7 If the field sample contained any cobbles or boulders or
both, the words with cobbles, or with cobbles and boulders
shall be added to the group name. For example, silty gravel
with cobbles, GM.

(1)
(2)

where:
13. Report
13.1 The report should include the group name, group
symbol, and the results of the laboratory tests. The particle-size
distribution shall be given in terms of percent of gravel, sand,
and fines. The plot of the cumulative particle-size distribution
curve shall be reported if used in classifying the soil. Report
appropriate descriptive information according to the procedures in Practice D 2488. A local or commercial name or
geologic interpretation for the material may be added at the end
of the descriptive information if identified as such. The test
procedures used shall be referenced.

D10, D30, and D60 = the particle-size diameters corresponding to 10, 30, and 60 %, respectively, passing on the cumulative particle-size distribution curve, Fig. 5.
NOTE 9It may be necessary to extrapolate the curve to obtain the D10
diameter.

12.3.1 If less than 5 % of the test specimen passes the No.

200 (75-m) sieve, classify the soil as a well-graded gravel,
GW, or well-graded sand, SW, if Cu is greater than or equal to
4.0 for gravel or greater than 6.0 for sand, and Cc is at least 1.0
but not more than 3.0.
12.3.2 If less than 5 % of the test specimen passes the No.
200 (75-m) sieve, classify the soil as poorly graded gravel,
GP, or poorly graded sand, SP, if either the Cu or the Cc
criteria for well-graded soils are not satisfied.
12.4 If more than 12 % of the test specimen passes the No.
200 (75-m) sieve, the soil shall be considered a coarsegrained soil with fines. The fines are determined to be either
clayey or silty based on the plasticity index versus liquid limit
plot on Fig. 4. (See 9.8.2.1 if insufficient material available for
testing) (see Note 7).
12.4.1 Classify the soil as a clayey gravel, GC, or clayey
sand, SC, if the fines are clayey, that is, the position of the
plasticity index versus liquid limit plot, Fig. 4, falls on or above
the A line and the plasticity index is greater than 7.

NOTE 11Example: Clayey Gravel with Sand and Cobbles (GC)

46 % fine to coarse, hard, subrounded gravel; 30 % fine to coarse, hard,
subrounded sand; 24 % clayey fines, LL = 38, PI = 19; weak reaction with
HCl; original field sample had 4 % hard, subrounded cobbles; maximum
dimension 150 mm.

In-Place Conditionsfirm, homogeneous, dry, brown,

Geologic Interpretationalluvial fan.
NOTE 12Other examples of soil descriptions are given in Appendix
X1.

14. Precision and Bias

14.1 Criteria for acceptability depends on the precision and
bias of Test Methods D 422, D 1140 and D 4318.
8

D 2487 06
15. Keywords
15.1 Atterberg limits; classification; clay; gradation; gravel;
laboratory classification; organic soils; sand; silt; soil classification; soil tests

APPENDIXES
(Nonmandatory Information)
X1. EXAMPLES OF DESCRIPTIONS USING SOIL CLASSIFICATION

X1.1.3 Organic Clay (OL)100 % fines, LL (not

dried) = 32, LL (oven dried) = 21, PI (not dried) = 10; wet,
dark brown, organic odor, weak reaction with HCl.
X1.1.4 Silty Sand with Organic Fines (SM)74 % fine to
coarse, hard, subangular reddish sand; 26 % organic and silty
dark-brown fines, LL (not dried) = 37, LL (oven dried) = 26, PI
(not dried) = 6, wet, weak reaction with HCl.
X1.1.5 Poorly Graded Gravel with Silt, Sand, Cobbles and
Boulders (GP-GM)78 % fine to coarse, hard, subrounded to
subangular gravel; 16 % fine to coarse, hard, subrounded to
subangular sand; 6 % silty (estimated) fines; moist, brown; no
reaction with HCl; original field sample had 7 % hard, subrounded cobbles and 2 % hard, subrounded boulders with a
maximum dimension of 18 in.

X1.1 The following examples show how the information

required in 13.1 can be reported. The appropriate descriptive
information from Practice D 2488 is included for illustrative
purposes. The additional descriptive terms that would accompany the soil classification should be based on the intended use
of the classification and the individual circumstances.
X1.1.1 Well-Graded Gravel with Sand (GW)73 % fine to
coarse, hard, subangular gravel; 23 % fine to coarse, hard,
subangular sand; 4 % fines; Cc = 2.7, Cu = 12.4.
X1.1.2 Silty Sand with Gravel (SM)61 % predominantly
fine sand; 23 % silty fines, LL = 33, PI = 6; 16 % fine, hard,
subrounded gravel; no reaction with HCl; (field sample smaller
than recommended). In-Place ConditionsFirm, stratified and
contains lenses of silt 1 to 2 in. thick, moist, brown to gray;
in-place density = 106 lb/ft3 and in-place moisture = 9 %.

X2. USING SOIL CLASSIFICATION AS A DESCRIPTIVE SYSTEM FOR SHALE, CLAYSTONE, SHELLS, SLAG, CRUSHED
ROCK, ETC.

After laboratory processing by slaking in water for 24 h,

material classified as Sandy Lean Clay (CL)61 % clayey
fines, LL = 37, PI = 16; 33 % fine to medium sand; 6 %
gravel-size pieces of shale.
X2.4.2 Crushed SandstoneProduct of commercial crushing operation; Poorly Graded Sand with Silt (SP-SM)91 %
fine to medium sand; 9 % silty (estimated) fines; dry, reddishbrown, strong reaction with HCl.
X2.4.3 Broken Shells65 % gravel-size broken shells;
31 % sand and sand-size shell pieces; 4 % fines; Cc = 2.4,
Cu = 1.9; would be classified as Poorly Graded Gravel with
Sand (GP).
X2.4.4 Crushed RockProcessed gravel and cobbles from
Pit No. 7; Poorly Graded Gravel (GP)89 % fine, hard,
angular gravel-size particles; 11 % coarse, hard, angular sandsize particles, dry, tan; no reaction with HCl; Cc = 2.4,
Cu = 0.9.

X2.1 The group names and symbols used in this standard

may be used as a descriptive system applied to materials that
exist in situ as shale, claystone, sandstone, siltstone, mudstone,
etc., but convert to soils after field or laboratory processing
(crushing, slaking, etc.).
X2.2 Materials such as shells, crushed rock, slag, etc.,
should be identified as such. However, the procedures used in
this standard for describing the particle size and plasticity
characteristics may be used in the description of the material.
If desired, a classification in accordance with this standard may
be assigned to aid in describing the material.
X2.3 If a classification is used, the group symbol(s) and
group names should be placed in quotation marks or noted with
some type of distinguishing symbol. See examples.
X2.4 Examples of how soil classifications could be
incorporated into a description system for materials
that are not naturally occurring soils are as follows:
X2.4.1 Shale ChunksRetrieved as 2- to 4-in. pieces of
shale from power auger hole, dry, brown, no reaction with HCl.

D 2487 06
X3. PREPARATION AND TESTING FOR CLASSIFICATION PURPOSES BY THE WET METHOD

X3.7 Determine the liquid limit and plasticity index as

follows:
X3.7.1 If the soil disaggregates readily, mix on a clean, hard
surface and select a representative sample by quartering in
accordance with Practice C 702.
X3.7.1.1 If the soil contains coarse-grained particles coated
with and bound together by tough clayey material, take
extreme care in obtaining a representative portion of the No. 40
(425-m) fraction. Typically, a larger portion than normal has
to be selected, such as the minimum weights required in 7.2.
X3.7.1.2 To obtain a representative specimen of a basically
cohesive soil, it may be advantageous to pass the soil through
a 34-in. (19-mm) sieve or other convenient size so the material
can be more easily mixed and then quartered or split to obtain
the representative specimen.
X3.7.2 Process the representative specimen in accordance
with Procedure B of Practice D 2217.
X3.7.3 Perform the liquid-limit test in accordance with Test
Method D 4318, except the soil shall not be air dried prior to
the test.
X3.7.4 Perform the plastic-limit test in accordance with Test
Method D 4318, except the soil shall not be air dried prior to
the test, and calculate the plasticity index.

X3.1 This appendix describes the steps in preparing a soil

sample for testing for purposes of soil classification using a
wet-preparation procedure.
X3.2 Samples prepared in accordance with this procedure
should contain as much of their natural water content as
possible and every effort should be made during obtaining,
preparing, and transportating the samples to maintain the
natural moisture.
X3.3 The procedures to be followed in this standard assume
that the field sample contains fines, sand, gravel, and plus 3-in.
(75-mm) particles and the cumulative particle-size distribution
plus the liquid limit and plasticity index values are required
(see 9.8). Some of the following steps may be omitted when
they are not applicable to the soil being tested.
X3.4 If the soil contains plus No. 200 (75-m) particles that
would degrade during dry sieving, use a test procedure for
determining the particle-size characteristics that prevents this
degradation.
X3.5 Since this classification system is limited to the
portion of a sample passing the 3-in. (75-mm) sieve, the plus
3-in. (75-mm) material shall be removed prior to the determination of the particle-size characteristics and the liquid limit
and plasticity index.

X3.8 Determine the particle-size distribution as follows:

X3.8.1 If the water content of the fraction passing the 3-in.
(75-mm) sieve was required (X3.6.3), use the water-content
specimen for determining the particle-size distribution. Otherwise, select a representative specimen in accordance with
Practice C 702 with a minimum dry weight as required in 7.2.
X3.8.2 If the cumulative particle-size distribution including
a hydrometer analysis is required, determine the particle-size
distribution in accordance with Test Method D 422. See 9.7 for
the set of required sieves.
X3.8.3 If the cumulative particle-size distribution without a
hydrometer analysis is required, determine the particle-size
distribution in accordance with Test Method C 136. See 9.7 for
the set of required sieves. The specimen should be soaked until
all clayey aggregations have softened and then washed in
accordance with Test Method C 117 prior to performing the
particle-size distribution.
X3.8.4 If the cumulative particle-size distribution is not
required, determine the percent fines, percent sand, and percent
gravel in the specimen in accordance with Test Method C 117,
being sure to soak the specimen long enough to soften all
clayey aggregations, followed by Test Method C 136 using a
nest of sieves which shall include a No. 4 (4.75-mm) sieve and
a No. 200 (75-m) sieve.
X3.8.5 Calculate the percent fines, percent sand, and percent gravel in the minus 3-in. (75-mm) fraction for classification purposes.

X3.6 The portion of the field sample finer than the 3-in.
(75-mm) sieve shall be obtained as follows:
X3.6.1 Separate the field sample into two fractions on a
3-in. (75-mm) sieve, being careful to maintain the natural water
content in the minus 3-in. (75-mm) fraction. Any particles
adhering to the plus 3-in. (75-mm) particles shall be brushed or
wiped off and placed in the fraction passing the 3-in. (75-mm)
sieve.
X3.6.2 Determine the air-dry or oven-dry weight of the
fraction retained on the 3-in. (75-mm) sieve. Determine the
total (wet) weight of the fraction passing the 3-in. (75-mm)
sieve.
X3.6.3 Thoroughly mix the fraction passing the 3-in. (75mm) sieve. Determine the water content, in accordance with
Test Method D 2216, of a representative specimen with a
minimum dry weight as required in 7.2. Save the water-content
specimen for determination of the particle-size analysis in
accordance with X3.8.
X3.6.4 Compute the dry weight of the fraction passing the
3-in. (75-mm) sieve based on the water content and total (wet)
weight. Compute the total dry weight of the sample and
calculate the percentage of material retained on the 3-in.
(75-mm) sieve.

10

D 2487 06
X4. AIR-DRIED METHOD OF PREPARATION OF SOILS FOR TESTING FOR CLASSIFICATION PURPOSES

limit and plasticity index as follows (see 9.8 for when these
tests are required):

X4.1 This appendix describes the steps in preparing a soil

sample for testing for purposes of soil classification when
air-drying the soil before testing is specified or desired or when
the natural moisture content is near that of an air-dried state.

X4.5.1 Thoroughly mix the fraction passing the 3-in. (75mm) sieve.
X4.5.2 If the cumulative particle-size distribution including
a hydrometer analysis is required, determine the particle-size
distribution in accordance with Test Method D 422. See 9.7 for
the set of sieves that is required.
X4.5.3 If the cumulative particle-size distribution without a
hydrometer analysis is required, determine the particle-size
distribution in accordance with Test Method D 1140 followed
by Test Method C 136. See 9.7 for the set of sieves that is
required.
X4.5.4 If the cumulative particle-size distribution is not
required, determine the percent fines, percent sand, and percent
gravel in the specimen in accordance with Test Method D 1140
followed by Test Method C 136 using a nest of sieves which
shall include a No. 4 (4.75-mm) sieve and a No. 200 (75-m)
sieve.
X4.5.5 If required, determine the liquid limit and the plasticity index of the test specimen in accordance with Test
Method D 4318.

X4.2 If the soil contains organic matter or mineral colloids

that are irreversibly affected by air drying, the wet-preparation
method as described in Appendix X3 should be used.
X4.3 Since this classification system is limited to the
portion of a sample passing the 3-in. (75-mm) sieve, the plus
3-in. (75-mm) material shall be removed prior to the determination of the particle-size characteristics and the liquid limit
and plasticity index.
X4.4 The portion of the field sample finer than the 3-in.
(75-mm) sieve shall be obtained as follows:
X4.4.1 Air dry and weigh the field sample.
X4.4.2 Separate the field sample into two fractions on a
3-in. (75-mm) sieve.
X4.4.3 Weigh the two fractions and compute the percentage
of the plus 3-in. (75-mm) material in the field sample.
X4.5

Determine the particle-size distribution and liquid

X5. ABBREVIATED SOIL CLASSIFICATION SYMBOLS

X5.1 In some cases, because of lack of space, an abbreviated system may be useful to indicate the soil classification
symbol and name. Examples of such cases would be graphical
logs, databases, tables, etc.

s = sandy
g = gravelly

X5.2 This abbreviated system is not a substitute for the full

name and descriptive information but can be used in supplementary presentations when the complete description is referenced.

X5.4 The soil classification symbol is to be enclosed in

parentheses. Some examples would be:
Group Symbol and Full Name
CL, Sandy lean clay
SP-Sm, Poorly graded sand with silt and gravel
GP, poorly graded gravel with sand, cobbles, and
boulders
ML, gravelly silt with sand and cobbles

X5.3 The abbreviated system should consist of the soil

classification symbol based on this standard with
appropriate lower case letter prefixes and suffixes
as:
Prefix

s = with sand
g = with gravel
c = cobbles
b = boulders

Suffix

11

Abbreviated
s(CL)
(SP-SM)g
(GP)scb
g(ML)sc

D 2487 06
SUMMARY OF CHANGES
In accordance with Committee D18 policy, this section identifies the location of changes to this standard since
the last edition (2000) that may impact the use of this standard.
(1) Added Test Method D 6913 to Section 2 and 7.2.
(2) Corrected 7.2 in selecting size of a sample.

(3) Corrected Example X2.4.3 .

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org).

12