Efek Pockel p5451 - e PDF

LD
Physics
Leaflets
Optics
Polarization
Pockels effect
P5.4.5.1
Demonstrating
the Pockels effect
in a conoscopic beam path
Objects of the experiment

To identify the optical axis of the birefringent crystal of the Pockels cell in a conoscopic beam path.
To demonstrate the Pockels effect in a conoscopic beam path.
To measure the half-wave voltage of the Pockels cell.
Principles
The Pockels effect
The Pockels effect is the name given to the occurrence of
birefringence and to the change in existing birefringence phenomena in an electric field linearly proportional to the electric
field strength. It is related to the Kerr effect, although in the
latter case the birefringence increases exponentially with the
electric field strength. For reasons of symmetry, the Pockels
effect can only occur in crystals with no inversion center,
whereas the Kerr effect can occur in all substances.
When the direction of the light beam and the optical axis of
birefringence are perpendicular to each other, we call this a
transverse configuration (see Fig. 1). The electric field is
applied in the direction of the optical axis. For Pockels cells in
the transverse configuration, lithium niobate (LiNbO3) is most
often used.
Fig. 1: Schematic diagram of a Pockels cell in transverse configuration
Lithium niobate crystals are optically uniaxial, negatively

birefringent and have the main refractive indexes no = 2.29 for
the ordinary beam, and ne = 2.20 for the extraordinary beam
(measured using the wavelength of the He-Ne laser, l =
632.8 nm.
Fig. 2: Diagram of a conoscopic beam path for demonstrating

birefringence
Birefringence in a conoscopic beam path
0206-Sel
The proof of birefringence in a conoscopic beam path is

described in numerous optics textbooks. A crystal with planeparallel cut faces is illuminated with a divergent, linearly
polarized light beam, and the light passing through it is observed behind a perpendicularly aligned analyzer (see Fig. 2).
The optical axis of the birefringence is clearly apparent in the
interference image, as it is indicated by the symmetry in its
vicinity. In this experiment, the optical axis is parallel to the
entrance and exit surfaces; this is why the interference pattern
consists of two sets of hyperbolas [1] which are rotated by 908
with respect to one another. The real axis of the first hyperbola
set is parallel to the optical axis, while that of the second set
is perpendicular to the optical axis.
P5.4.5.1
LD Physics Leaflets
Apparatus
1 Pockels cell . . . . . . . . . . . . . . . . .
1 High-voltage power supply, 10 kV . . . . .
1 He-Ne laser, linearly polarized . . . . . . .
472 90
521 70
471 480
1 Lens in holder, f = 5 mm . . . . . . . . . .
1 Lens in holder, f = 50 mm . . . . . . . . . .
1 Polarization filter . . . . . . . . . . . from
1 Optical bench, 1 m, standard cross-section
5 Optics riders, H = 60 mm, W = 36 mm . . .
460 01
460 02
472 40
460 32
460 353
1 Translucent screen . . . . . . . . . . . . .
1 Saddle base . . . . . . . . . . . . . . . . .
441 53
300 11
1 Safety connection lead, red . . . . . . . .

1 Safety connection lead, blue . . . . . . . .
1 Safety connection lead, 10 cm . . . . . . .
500 641
500 642
500 604
The dark lines of the interference image are caused by light

rays for which the difference between the optical paths of the
extraordinary and the ordinary partial beam in the crystal is an
integral multiple of the wavelength. These light rays retain their
original linear polarization after passage through the crystal,
and are extinguished in the analyzer. The light rays reaching
the center of the interference image are normally incident on
the surface of the crystal. For these rays, the path difference
between the extraordinary and the ordinary partial beam is
D = d (no ne),
Fig. 3: Interference pattern in the conoscopic beam path with the

optical axis of the crystal in the direction of the arrow. The
numbers represent the path difference between the ordinary and the extraordinary partial beam. Thus for example
the lines with the value +1(1) have the path difference
Dm+1 (Dm1)
(I)
where d = 20 is the thickness of the crystal in the direction of

the beam. The path difference corresponds to approximately
2800 wavelengths of the laser light used. however, D is not
usually precisely a whole multiple of l, but rather lies between
two values, Dm = m l and Dm+1 = (m + 1) l. The dark lines
in the first hyperbola set thus correspond to the path differences Dm+1, Dm+2, Dm+3, etc., and those of the second set to
Dm, Dm1, Dm2, etc. (Fig. 3). The position of the dark lines, or
better their distance from the center, depends on the magnitude of the difference between D and m l.
The Pockels effect magnifies or reduces the difference of the

main refractive indices no ne, depending on the sign of the
applied voltage. This in turn alters the difference D m l, and
thus the position of the dark interference lines. If the so-called
half-wave voltage Up is applied, the value of D is changed by
one-half wavelength. The dark interference lines shift to the
positions of the bright lines, and vice versa. This process
repeats itself each time the voltage is increased by Up.
Setup
Safety note
Notes:
The He-Ne laser fulfills the German technical standard

Safety Requirements for Teaching and Training Equipment Laser, DIN 58126, Part 6 for class 2 lasers. When
the precautions described in the Instruction Sheet are
observed, experimenting with the He-Ne laser is not
dangerous.
Carry out all measurements in a darkened room.

Do not insert the rods of the optical components all the way in
the optics riders, so that subsequent fine adjustment of the
height can be carried out.
Fig. 4 shows the experiment setup; the position of the left edge
of each optics rider is given in cm.
Never look directly into the direct or reflected laser

beam.
Do not exceed the glare limit (i. e. no observer should
feel dazzled).
Setting up the optical components:
Mount the He-Ne laser, the 5-mm lens (a) and the 50-mm
lens (b). Carefully turn the laser and the 5-mm lens and
adjust their heights so that optimum illumination of the
50-mm lens is achieved.
Set up the translucent screen at a suitable distance, and
attach a piece of white paper to the screen.
P5.4.5.1
LD Physics Leaflets
b) Demonstrating the Pockels effect:
Fig. 4: Experiment setup for demonstrating the Pockels effect

(a) Lens, f = 5 mm
(b) Lens, f = 50 mm
(c) Pockels cell
(pointer position: 458 with respect to analyzer)
(d) Polarization filter as analyzer
(pointer position: 908 to polarization direction of laser)
Return the pointer on the Pockels cell to the initial position

(+458 or 458 with respect to the analyzer).
Slowly increase the voltage U (do not exceed 2 kV!) and

observe the changes in the interference pattern.
Reduce the voltage to 0 V, connect the plus-socket of the
Set up the polarization filter as the analyzer and vary the
direction of polarization until you obtain the minimum intensity on the screen.
Add the Pockels cell to the assembly and slide it into the
exact position of the minimum beam cross-section. Observe the screen and make sure that light reflections on the
interior surfaces of the crystal and the plate capacitor in the
Pockels cell are avoided.
Turn the pointer by either +458 or 458 with respect to the
analyzer.
high-voltage power supply to the ground socket and

reverse the connections on the Pockels cell.
Once again, increase the voltage U (do not exceed 2 kV!)
and observe the changes in the interference pattern.
c) Determining the half-wave voltage:
Set the voltage to U = 0 V and mark the dark lines of the
interference pattern on the piece of paper using a green

pen.
Slowly increase the voltage U and record each value at
which the bright and dark interference lines are exactly
congruent with the markings on the piece of paper.
Fine adjustment:
Adjust the height of the laser, the 5-mm lens and, if neces-
sary, the Pockels cell as well until the center of the hyperbola sets in the interference pattern is in the center of the
field of view.
If necessary, turn the Pockels cell on the rod axis.
Measuring example and evaluation

a) Demonstrating birefringence:
Electrical connections:
When the Pockels cell is rotated around the axis of the light
beam, the interference image turns as well. In this case, the
real axis of the first hyperbola set is always parallel to the
optical axis of the crystal (indicated by the direction of the
pointer).
Connect the Pockels cell to the left output of the high-volt
age power supply (max. short-circuit current 100 mA); be

sure to connect the minus-socket to the ground socket.
Turn the potentiometer of the power supply all the way to
the left; then switch on the high-voltage power supply and
activate the left-hand output with the selector button.
Carrying out the experiment
Maximum bright-dark contrast is achieved when the angle

between the optical axis and the analyzer is 458. The screen
is dark when the optical axis is parallel or perpendicular to the
analyzer.
a) Demonstrating birefringence:
b) Demonstrating the Pockels effect:
Compare the position of the hyperbola set in the interfer-
When the voltage has the correct polarity, the dark interference
lines of the first hyperbola set (real axis of the hyperbolas
parallel to the optical axis of the crystal) move toward the
center as the voltage increases, while those of the second
hyperbola set move away from the center.
ence pattern with the position of the pointer on the Pockels

cell.
Slowly vary the position of the pointer on the Pockels cell
and note the changes in the interference pattern.
P5.4.5.1
LD Physics Leaflets
The two hyperbolas with the path difference Dm+1 = (m + 1) l

move to the center at a voltage U1 (see Fig. 5); thus, the center
is dark. When the voltage is increased further, the two hyperbolas change over to the second hyperbola set and there
become continuously larger. At a voltage U2 the next two
hyperbolas move across the center to the other hyperbola set,
the following two at a voltage U3 and so on. The interval
between the voltages U1, U2 and U3 corresponds to twice the
half-wave voltage (see below).
When the polarity of the voltage is reversed, the hyperbolas
move in the opposite direction. Thus, the difference of the main
refractive indexes no ne increases or decreases due to the
Pockels effect, depending on the polarity of the voltage.
c) Determining the half-wave voltage:
At the values for the voltage U given in Table 1, the intensity of

the lines at the marked points in the interference pattern
change from bright to dark, as the path difference between the
ordinary and the extraordinary partial beam changes by onehalf the wavelength. The difference between these voltages is
the half-wave voltage Up. This has a value of approx. 0.5 V.
The change in the birefringence dno dne after applying the
half-wave voltage is very small. Using equation (I), we can
calculate
l
= d (dno dne),
2
(II)
and obtain
dno dne = 16 1016
Table 1: Measurement results for determination of the halfwave voltage
U
kV
Brightness on translucent
screen at the marked
location
0.0
Dark
0.52
Bright
1.01
Dark
1.52
Bright
1.91
Dark
LD DIDACTIC GmbH
by LD DIDACTIC GmbH
Bibliography
[1] M. Born and E. Wolf, Principles of Optics, Pergamon Press
Fig. 5: Changes in the conoscopic interference image due to

the Pockels effect; the respective hyperbola of the interference order m + 1 are emphasized with bold lines
Leyboldstrasse 1 D-50354 Hrth Phone (02233) 604-0 Telefax (02233) 604-222 E-mail: [email protected]
Printed in the Federal Republic of Germany
Technical alterations reserved

Efek Pockel p5451 - e PDF

Uploaded by

Copyright:

Available Formats

Efek Pockel p5451 - e PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Efek Pockel p5451 - e PDF

Uploaded by

Copyright:

Available Formats

What is the Pockels effect and how does it relate to birefringence?

What is the Pockels effect and how does it relate to birefringence?

How can the Pockels effect be demonstrated using a conoscopic beam path?

How can the Pockels effect be demonstrated using a conoscopic beam path?

LD

Objects of the experiment

Fig. 1: Schematic diagram of a Pockels cell in transverse configuration

Lithium niobate crystals are optically uniaxial, negatively

Fig. 2: Diagram of a conoscopic beam path for demonstrating

Birefringence in a conoscopic beam path

The proof of birefringence in a conoscopic beam path is

1 Safety connection lead, red . . . . . . . .

The dark lines of the interference image are caused by light

Fig. 3: Interference pattern in the conoscopic beam path with the

where d = 20 is the thickness of the crystal in the direction of

The Pockels effect magnifies or reduces the difference of the

The He-Ne laser fulfills the German technical standard

Carry out all measurements in a darkened room.

Never look directly into the direct or reflected laser

Setting up the optical components:

b) Demonstrating the Pockels effect:

Fig. 4: Experiment setup for demonstrating the Pockels effect

Return the pointer on the Pockels cell to the initial position

Slowly increase the voltage U (do not exceed 2 kV!) and

Reduce the voltage to 0 V, connect the plus-socket of the

Set up the polarization filter as the analyzer and vary the

high-voltage power supply to the ground socket and

c) Determining the half-wave voltage:

Set the voltage to U = 0 V and mark the dark lines of the

interference pattern on the piece of paper using a green

Measuring example and evaluation

Connect the Pockels cell to the left output of the high-volt

age power supply (max. short-circuit current 100 mA); be

Carrying out the experiment

Maximum bright-dark contrast is achieved when the angle

b) Demonstrating the Pockels effect:

Compare the position of the hyperbola set in the interfer-

ence pattern with the position of the pointer on the Pockels

The two hyperbolas with the path difference Dm+1 = (m + 1) l

At the values for the voltage U given in Table 1, the intensity of

Table 1: Measurement results for determination of the halfwave voltage

Fig. 5: Changes in the conoscopic interference image due to

You might also like