Ger 3419a Gas Turbine Inlet Air Treatment

Download as pdf or txt
Download as pdf or txt
You are on page 1of 26

GER-3419A

RL. Loud
and
AA Slaterpryce
Engineer, Gas Turbine
.wer, Gas Turbine
Power Plant Systems
General Elect& Compasiy
Schenectady, NY

AIRFILTRATION

CONTENTS
Page

Need for Filtration

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Air Filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..-..... 1
Anti-Icing Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Inlet Cooling Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
A Table Conversion Factors is included at the
end of this publication.

Any gas turbine, due to its inherent design


and the enormous amount of air consumed
(e.g. 1296 lb/s or 587 kg/s for the MS9001F), is
sensitive to air quality. Filtration is applied to
provide protection against the effects of contaminated air that may degrade gas turbine performance and life: erosion, fouling, corrosion, and
cooling passage plugging. The need for proper
filtration has increased in significance due to
the complex designs of the advanced technology
7F and 9F machines.

INTRODUCTION

Gas turbines manufactured by General Electric


Company are operating successfully in rural areas
and heavy industrial zones, in polar regions and
the tropics, in deserts and at sea In order to adapt
machines to a variety of environments while realizing their full potential in performance and reliability, it is often necessary to treat the air which
they consume. Even in relatively clean environments, a gas turbine may ingest hundreds of
pounds of foreign matter each year. Whether or
not this will cause a problem depends on the
amount of this material, its mechanical properties,
and its chemical composition. The hazards of
nonremoval include erosion of compressor and
turbine components, fouling of compressor airfoils, and corrosion. Solid particles are removed
by appropriate filters, while potentially corrosive
liquids are removed by moisture separators.
In warmer climates, the power available from
a gas turbine may be increased by using an evap
orative cooler or a chilled water cooling system.
Conversely, in very cold environments it is necessary to avoid icing of components such as inlet
filtration and the trash screen, silencers, and
inlet guide vanes.
This paper will discuss in detail the environmental conditions that indicate need for inlet
air treatment, the specific equipment utilized by
General Electric to perform these functions,
and their impact on gas turbine operation.

Erosion
Both the axial compressor and the hot-path
parts can be affected by erosion from hard, abrasive particles, such as sand and mineral dusts.
As these particles impact upon the compressor blades, they cut away a small amount of
metal. The net rate of erosion, although not
precisely quantifiable, depends on the kinetic
energy change as the particles impinge, on the
number of particles impinging per unit time,
the angle of impingement, and on the mechanical properties of both the particles and the
material being eroded.
In general, our gas turbine experience indicates that particles below 10pm do not cause
erosion, whereas particles 20pm and above
normally cause erosion when present in sufficient quantities.
Two examples of eroded parts, a compressor
blade and a first-stage nozzle, are shown in
Figs. 1 and 2. Not only does erosion reduce
aerodynamic performance, but the reduction
in cross-sectional area of the compressor blade
could lead to serious turbine damage if,
because of increased local stresses, it should
break loose during operation. Air filtration
methods are available which can easily and very
efficiently remove airborne particles of 1Opm
and above.
1

ERODED FIRST-STAGE NOZZLE AIR FOIL

COMPRESSOR

TC 197421

Figure 1

Figure 2
blades. One of these is the use of mild abrasive
cleaning materials such as crushed nutshells
which, when ingested at a controlled rate into
the compressor during operation, remove some
or all of these deposits (depending on their
nature). Recent experience has shown that the
use of abrasive cleaning can damage compressor
blade coatings and compressor blade surface finish. Abrasive cleaning compounds are also a
potential cause of plugged cooling passages
which will be descussed shortly. For these reasons, abrasive cleaning is generally not recommended on any size turbine, and definitely not
recommended on the advanced technology turbines. General Electric Instruction GEL41042
should be consulted for the use of any abrasive
compressor cleaning agents on GE gas turbines.
More recent work within the industry has
shown that certain ash-free detergents are very
effective in removing compressor blade deposits.
Both offline and online water wash systems are
available. Offline involves injecting the cleaning
solution into the compressor while it is turning
at cranking speed. Online is not as effective as
offline but has the advantage that it can be

Compressor Fouling
The efficiency of an axial compressor is depen-

dent on, among other considerations, the

smoothness of the rotating and stationary blade


surfaces. These surfaces can be roughened by
erosion, but more frequently roughening is
caused by the ingestion of substances which
adhere to the surfaces. These include oil vapors,
smoke, and sea salt. Figure 3 shows deposits
formed on the leading edge of rotating blades.
The output of a turbine can be reduced as much
as 20 percent in cases of extreme compressor
fouling. The rate at which this fouling takes place
is difficult to quantify because it depends not only
on the types and quantities of materials ingested,
but also on the peculiar properties of the substances that cause them to stick. Filtration can
remove some, but not all, of these substances.
Certain vapors that are adhesive when they condense can pass through filters. Other vapors may
originate between the filter and the compressor,
such as occasional lubricating oil leaks.
Fortunately, today there are ways of removing
these adhesive deposits from the compressor

EFFECT OF CLEANING ON GT OUTPUT

OUTPUT
LOSS

FIRED

HOURS

GTO 415;
GTO 4151

Figure 3

Figure 4
2

applied during turbine operation. Specific water


wash chemical recommendations are contained
in GEI41042.
Figure 4 shows the effect of compressor cleaning on gas turbine output. It shows that output
deteriorates along a decaying exponential curve
as the compressor continues to foul. Removal of
the fouling deposits restores gas turbine output
to nearly the original value.

= Steam-to-fuel mass flow ratio


x, = Contaminant concentration
(weight) in fuel (ppm>
x, = Contaminant concentration
(weight) in inlet air (ppm)
Xs = Contaminant concentration
(weight) in injected
steam/water (ppm)

Compressor Corrosion

When concentrations of trace metals in fuel,


water, or steam are not precisely known, a limit for
these contaminants in the inlet air of 0.005 ppm
will normally be set This limit, based on experience, would cause an insignificant contribution to
the overall contaminant level and have a minor
effect on parts lives. Reference should be made to
the appropriate fuel specification for guidance.

Corrosion of compressor components can be


caused by wet deposits of sea salt, acids, and other
deleterious materials. In addition to rusting of
compressor wheels, such corrosion is also manifested as pitting of the compressor blading. Pitting
causes a roughening of the airfoils with consequent reduction in the aerodynamic performance
of the compressor. These pits also cause local stress
risers and may diminish the fatigue life of the
blades. In addition to filtration, protective coatings
for both blading and wheels have been very effective where environments are known to contain corrosive compounds.

Cding Passage Plugging


Flow of cooling air through passages in the
combustion liner, nozzles, and buckets is necessary to control metal temperatures of these
parts. Since the cooling flow is extracted from
the compressor of the gas turbine, contaminants
in the inlet air may also be present in the cooling air. If these contaminants cause a buildup in
the cooling passages, heat transfer is degraded
and temperatures may increase to levels which
give rise to cracking. This is especially critical in
the advanced technology F machines which,
because of their higher firing temperatures,
require a very complex system of cooling passages. Coal dust, cement dust, and fly ash are
particularly bad, since they tend to sinter.

Hot-Section Corrosion
Possibly the single most important and frequently encountered consequence of inadequate
air filtration has to do with the ingestion of certain metals which, after combining with sulfur
and/or oxygen during the combustion process,
deposit on the surfaces of the hot gas path parts.
These parts include combustion liners, transition
pieces, nozzle partitions and turbine buckets.
There are four such metals which are of primary
concern: sodium (Na), potassium (K), vanadium
(V) and lead (Pb). These metals, either as sulfates or oxides, cause the normally protective
oxide film on hotgaz+path parts to be disrupted
so that the parts oxidize several times faster than
in the presence of gases free of them.lJ They may
be found in fuels and in water or steam, as well
as in the inlet air. Allowable limits are set forth in
GEI-41047. The effects of these contaminants on
the turbine are also discussed in this reference.
The following relationship may be used to calculate the limits in the inlet air:

Environments
Ambient air can be contaminated by solids,
liquids, or gases. Of these three, contamination
by solids is the most common, and usually the
most serious situation. The quantity of solids can
be defined in many ways, such as milligrams per
cubic meter of air or grains per 1000 cubic feet.
A measure General Electric finds convenient is
parts per million (ppm), i.e., the mass of contaminants per million units mass of air. The fact
that this is a convenient measure immediately
demonstrates that the quantity of dust is generally quite small compared to the mass of air..
However, when account is taken ofthe large:
flow rates of gas turbines, it is evident that the
total quantity of dust which is ingested can be
appreciable when summed over hundreds or
thousands of fired hours.

(A)&+ 6)
(F)*+*
(F)
Equivalent contaminants in fuel alone
where
++ = Air-to-fuel massflow ratio
3

several hours, while long-term levels may average one to five ppm. When the wind blows in
these regions, the larger soil particles become
airborne first, smaller particles being more
adherent. When the large particles fall back to
earth, they disturb the surface and splash out
fine particles. By Stokes law, fine particles settle
more slowly; so they remain airborne longer.
The results are that the dust concentration is
highest close to the ground, and that the particles there tend to be coarser than at higher elevations. There is no exact relationship between
dust concentration and elevation above ground,
but available data generally tend to fall within
the range of Fig. 6. This shows that elevating a
filter compartment some 20 ft. in the air approximately halves the dust load, compared to a
ground-mounted compartment.
The size distributions of airborne dusts are
variable with respect to time and place. In general, high values of dust concentration tend to
be associated with coarse dust and low values
with fine dust. Large dust particles tend to fall
out quickly, while smaller particles are more
likely to stay airborne. Consequently, dust samples taken near the source of contamination
tend to be coarser than those samples taken at
a distance.
Some idea of the size distributions experienced in practice can be had by reference to the
standardized dusts, Arizona Coarse and Arizona
Fine, which are widely used in the testing of air
filtration devices. Table 1 shows their mass distribution as a function of particle size. Since the

In the United States, the Environmental


Protection Agency samples airborne particulates periodically at some 4000 locations.
Results of the annual surveys are published, giving an excellent idea of the statistical variation
of dust loading at the test sites.4 The typical
range of values is shown in Fig. 5. Curve A gives
the percentage of U.S. sites exceeding a given
dust load 50 percent of the time; curve B shows
the percentage of test locations exceeding a
particular dust load 10 percent of the time.
These curves show that the typical dust concentration in most locations is from about 0.03 to
0.06 ppm, with occasional excursions at some
sites to 0.2 or 0.3 ppm. It must be understood
that particular locations may deviate significantly from these typical values. While the curves
are derived only from U.S. data, similar values
are to be expected in other developed countries
having temperate climates.
Dust loading in desert regions, particularly
those subject to sand and dust storms, is much
higher than those usually experienced in the
United States. Concentrations in sand storms
may reach several hundred ppm for periods of
PERCENTAGE OF U.S. SITES
EXCEEDING GIVEN DUST LOAD
. ..I
.*
AZ ,OlH PCRClllllLC
m IOTH PCCCWm.L
9,
10
B
PERCENT ,D
A
20
3

Table 1
Components of Arizona Road Dust

0.1lho
0.1
1.0
0.01
DUST LOAD. PPM
TO 767W

Particle Size
=%e
(mkrons)

Figure 5
TYPICAL VARIATION OF DUST
CONCENTRATION WITH ELEVATION

Nominal Percentage of
Total Mass of Particles
Course
Dust

Fine
Dust

O-5

12

39

5-10

12

18

lo-20

14

16

20-40

23

18

40-80

30

80-200

RELATIVE
OUST
COI(CENTRAlION

Figure 6
4

mass of a particle is proportional to the cube of


its diameter, it will be recognized that typical
dusts have many fine particles, and relatively few
particles of large diameter.
The chemical composition of airborne dusts
is significant, particularly with regard to sodium and potassium, which contribute to hot
corrosion. General Electric has analyzed many
dust samples from around the world. Typically,
it is found that airborne dust has about twice as
much of these elements as do local soils. This
apparent anomaly arises because the fine particles of soil tend to be richest in sodium and
potassium, and these particles stay suspended
in the air while larger particles fall back to
earth. Airborne dusts from different locations
vary widely in their composition, depending
partly on local soils and partly on industrial
pollutants released into the air. In general, the
most corrosive dusts come from desert regions
in which the soil is a former seabed. Sodium
and potassium may make up as much as 5 percent of the weight in extreme cases. Values of 1
to 3 percent are more typical. As an example,
suppose that the long-term average dust load at
a desert site is 3 ppm, and that the dust is 2
percent sodium plus potassium. The corrosive
content of the dust is therefore 3 x 0.02 = 0.06
ppm. Assuming a typical air/fuel mass ratio of
50:1, this is equivalent to 50 x 0.06 = 3 ppm
sodium plus potassium in the fuel. This is
excessive and indicates that inlet air filtration
would be required.

High-Efficiency Filters
Highefficiency filters use a special filter medium of fiberglass or treated paper to achieve good
collection efficiency for all particles, including
those as smaller than lpm. Figure 7 shows typical
efficiency as a function of particle size. Because
the collectiori efficiency is very high, the air quality downstream is also high, even when the ambient air is badly contaminated,
High efficiency filters generally take the form
of either a rectangular panel filter or a cylindrical cartridge filter. Other than their shape, the
two major difference2 are in the type of media
used and the design of the seal where the element is attached.
The panel filters typically contain a depth
loading media. Particles are actually trapped
within the body of the media itself. Depth loading media has a billowy texture which allows the
particles to penetrate. Cylindrical cartridge filters contain a surface loading media. This traps
the particles on the outside face where they
form a dust layer. This dust layer actually
enhances the collection efficiency of the filter
causing it to become more efficient with time. It
is the surface loading characteristic that allows
the dust to be dislodged during cleaning.
The seal on the filter element is another area
of prime importance. There is no point in providing filters of such high efficiency if contaminated
air is continually leaking past them. It is here that
the cylindrical cartridge has a distinct advantage
over the rectangular panel. Cylindrical cartridges
have a continuous, circular, neoprene gasket permanently affixed to each element. This gasket is
capable of making up for variations in the mating
surface. Panel filters have various types of sealing
mechanisms available, but none have shown to be
.as reliable as the cylindrical cartridge seal.
Rectangular panel filters are available as a
replaceable element which is held in shape by a

Equipment Description
Equipment designed. by General Electric to filter the inlet air can be divided into two classes,
conventional and self cleaning. Conventional filters include inertial separators and media-type filters; the latter are normally replaced when they
become dirty. Selfcleaning filters, introduced in
the 197Os, have become well accepted and now
account for 80 to 90% of the new systems sold by
General Electric. These are media-type filters
which have the ability to renew themselves by
automatically shedding accumulated dust
An important characteristic of an air filter is
its collection efficiency, calculated from the
weight of dust entering and leaving:

TYPICAL
FILTRATION
EFFICIENCY

EFFICIEKY

W entering -Wleaving
Efficiency =
W entering
x 100 (percent)
Collection efficiency varies with particle
size, typically being lower for small particles
than for large.

Figure 7
5

HIGH-EFFICIENCY FILTER

HIGHEFFICIENCY
FILTERS

G T O 7680

Figure 8

Figure 9

wire frame, Fig. S, or as an integral assembly


with the media bonded to a metal frame, Fig. 9.
Cylindrical cartridge filters are also integral
assemblies incorporating the frame and media
into a single unit, Fig. 10.
High-efficiency filters have an initial pressure
drop which depends upon their construction,
installation, and on the quantity of air passed
through each filter element. Filters normally use
pleated media in order to increase the available
surface area; this decreases pressure drop and
increases dust-holding capacity. As dust is accumulated, pressure drop rises. The rise is relatively slow at first, but increases more rapidly as the
filter nears the end of its useful life. A typical
design would have a new-and-clean pressure
drop of about an inch of water; the final pressure drop depends upon a trade-off between filter life and gas turbine performance. General
Electric recommends a final pressure drop of
2.5 in. as a good compromise for panel filters
and 4.0 in. for cylindrical cartridges.
The dust-holding capacity of a filter is an
important characteristic, since it relates to filter
life. Dust holding capacity is not easy to define,

since it depends upon the particle size distribution of the incident dust. For a given pressure
drop, a filter can hold a greater mass of large
particles than of small particles. Therefore, a filter will load up more quickly with fine dust
than with the same amount of sand. Filter manufacturers commonly use Arizona Fine test dust
to rate high-efficiency filters. This is reasonable,
since it provides a conservative rating which is
valid even in environments where larger particles may not be present in the ambient air.

Self-Cleaning Filters
Self-cleaning inlet filtration, developed in the
197Os, combines the effectiveness of the highefficiency filter with low maintenance. This combination of characteristics is realized by using a
barrier-type filter element which accumulates
dust on the surface which is exposed to the
ambient air. The collection efficiency is typical
of high-efficiency filters. When pressure drop
builds up to a predetermined level, the filter is
cleaned by a brief back-pulse of air, either
extracted from the gas turbine compressor, or

C R O S S - S E C T I O N QU,CX.NUT

EXPANDED METAL
INNER LINER

CYLINDRICAL
CARTRIDGE

PERFORPlTED METAL
OUTER LINER
SEALING
WASHER
GTZI 131

Figure 10

GT?114

Figure 11

derived from an auxiliary source. A filter compartment includes many filter elements, only a
few of which are cleaned at any given time; so
the airflow to the gas turbine is not disturbed by
the cleaning process.
The action of a selfcleaning filter is illustrated
in Fig. 11. Air flows through the filter elements
into a clean-air plenum. Dust in the air is trapped
on the surface of the lilter media, which is formed
from specially treated cellulose, synthetic, or combination cellulose/synthetic lilter paper. The filter
elements are typically in the form of cylindrical
cartridges. The paper is pleated in order to
increase the available sutice area. Many filter elements are used so that the velocity of the air
through the filter media is very low, in the range
of 2.5 to 3 ft/min. This low velocity decreases pressure drop, increases dust-holding capacity, and is
essential to the cleanability of the filters.
As the filters accumulate dust, the pressure drop
gradually rises. When the pressure in the clean-air
plenum reaches a particular value, usually set at 3
to 4 in. of water, gauge, cleaning is initiated. A
cleaning manifold is pressurized nominally to 100
psig with compressed air, extracted from the gas
turbine compressor or some other suitable source.
Upon command from the automatic sequencing
control, a solenoid-operated air valve directs a
brief (about 0.1 s) pulse of air into the filters. This
shocks and causes a momentary backflow through
the filters, dislodging accumulated dust from the
outside of the elements and allowing it to disperse.
Re-entrainment of dust is minimized by the lowvelocity design. The updraft and between filter
velocities are kept at or below 320 and 580 feet per
minute respectively. The process continues, cleaning a few filters at a time, until all elements have
been cleaned and pressure drop reduced to an
acceptable level. A single cleaning cycle is usually
completed in 20 to 30 minutes. This ensures that
the compartment can handle heavy dust loads,
such as those associated with sandstorms, without
excessive rise in pressure drop.
The filter elements are replaced when they
begin to show signs of deterioration caused by
heat and ultraviolet rays from the sun, or when
the cleaning cycle can no longer restore pressure drop. While this period cannot be quantified for all environments, experience indicates
about a two-year life in Middle-East deserts.
However, filter life may be sustantially lower in
extremely harsh environments such as those
heavily laden with airborne cement dust About
100 man-hours are required for complete filter
changeout for an MS7001 gas turbine.
Fipure 12 shows a typical self-cleaning compartment installed on 4 MS6001 gas turbine. It

SELF-CLEANING
INLET FILTER

Figure 12
includes several hundred filter elements, mounted in modules which feed into a tapered cleanair plenum. Each module has the filter elements
enclosed by a metal skirt, which protects them
from damage. The upward velocity of air into
self-cleaning modules is low, so the module acts
as its own weather hood. In order to reduce the
compartment footprint, the modules may be
arranged in two or more tiers. The lower tier of
modules acts as the platform for access to the
upper tier. Walkways, ladders, and railings are
provided as necessary for safe access. Since
access to the clean air plenum is infrequently
required, a bolt-on hatch is provided instead of
a door. There is a convenience outlet to aid interior inspections and maintanence. A differential
pressure gauge/pressure switch is supplied to
read plenum pressure, and control the operation of the self cleaning system. Alarms are provided for excessive differential pressure in the
plenum and for low pressure in the pulse cleaning air supply. Pressure switches are also provided to initiate a controlled shutdown in the event
that differential pressure in the plenum
becomes dangerously high.

Cartridge Type,
Non-Self Cleaning Filters
In environments where the concentration of
airborne contaminants or other considerations
make it impractical to pulse clean inlet filters,
the high efficiency selfcleaning type cylindrical
cartridges may still be used. Such a system can
be identical in configuration to the self-cleaning
compartment with the exception that the puls-.,
ing hardware is omitted.
This system acts as a static barrier filter while
maintaining many of the advantages of the self
cleaning system. Such advantages include high
dust holding capacity, positive sealing mecha7

TYPICAL PRESSURE-DROP HISTORY


INERTIAL
TYPE FILTER
PRESSURE
DROP
INCHES OF
WATER

VANE TYPE

AIR OUTLET

13x5FILTER CHANGEOUT

* COMPLETE CHANGEOUT
TOTAL AIR IN1

1924611

Figure 13

Figure 14

nism, inherent low velocities and low pressure


drop. The dust holding capacity of a single cylindrical self-cleaning we cartridge filter is on the
order of 2500 grams for Arizona Fine dust. Dust
holding capacities for high efficiency panel filters are in the range of 400 to 700 grams of dust.

percent of the primary flow. This system must be


in operation while the turbine is running to
ensure the collection of particles.
Another type of inertial separator is the spintype, shown in Fig. 15. The incoming air/dust
mixture is given a spin by the stationary inlet centrifugal blades, thereby causing the heavier particles to collect near the surface of the outer tube,
where they are scavenged by a bleed fan system.
The clean air is drawn through the center tube
and then on into the gas turbine. Spin tubes iypitally require more frontal area than van-type sep
arators, which may sometimes preclude their use.
While the arrangements of vane-type and
spin-type inertial separators are different, operationally they have much in common. Separation
efficiency rises rapidly at first as flow through
the separator increases; it then reaches a broad
plateau where higher flow has relatively small
effect on efficiency. Since increasing flow leads
to higher pressure drop, which lowers the performance of the gas turbine, the design engineer must balance separator cost and performance against gas turbine performance when
deciding the appropriate design point. The

Prefdters
If the ambient dust load is fairly high, as in
some industrial areas, it may be economical to
further protect the high-efficiency filters by
means of inexpensive, disposable media-type prefilters. The mounting frames for the prefilters are
typically placed directly in front of the high-efficiency filters which they protect. Figure 13 illustrates how the pressure drop of the entire filter
system typically varies with time. Three prefilter
changeouts are shown for each change of highefficiency filters, which is a common experience.
A typical two-stage filter system (prefilters and
high-efficiency filters) can remove several hundred pounds of dust from the gas turbine inlet
air before the high-efficiency filters must be
replaced. It is not possible to predict specific
results based on average filter life because each
site is unique; however, 5000 to 7000 fired hours
-is typical of two-stage systems in the United
States. Without prefilters, the life would be
decreased by a factor of two or more.

INERTIAL TYPE FILTER


SPIN TYPE

Inertial Separator
Air containing dust, dirt, and chemical contaminants enter the open end of a V-shaped
pocket (Fig. 14). The ends of the pocket are
solid, with both sides made up of louvered slots.
The dirt is separated from the air as the air
turns to pass through the open slots in the sides
and the larger dirt particles continue in a
straight line to a collection chute aided by a
bleed fan. The bleed rate is approximately 10

Fiie 15
8

usual choice is the point at which high collection efficiency is combined with acceptable pressure drop, typically 1.0 to 1.5 in. of water.
The bottom curve of Fig. 7 shows typical separation efficiency as a function of particle size.
Since the performance of an inertial separator is
excellent for particles larger than lOpm, this
provides a defense against the compressor erosion described previously. It is also effective
against corrosion if the corrosive particles are in
the greater-than-1Ollm size range.
Generally, inertial separators which, in a sense
are selfcleaning by design, are used as the first
stage of filtration, preceding high-efficiency filters. In this case, they extend the life of the
high-efficiency filters by removing some of the
dust which would otherwise cause them to foul.

PRECIPITATION TERMINAL VELOCITY

Figure 17
upward at low velocity, thereby discriminating
against the snow or rain which is falling downward at some terminal velocity. The terminal
velocities of different forms of precipitation vary
widely (Fig. 17) ,s and it is intuitively evident that
a given hood design will be more effective in
rejecting fast-falling raindrops than slow-falling
snowflakes. In order to quantify this, a modeling
study was conducted on the computer, taking
into account not only the geometry of the hood
and its associated flow field, but also such factors
as the drop-size distributions in rainstorms of
various intensities, Figure 18 gives the rejection
efficiency of single hoods as a function of face
velocity and rainfall rate. A curve is also given
for typical snow rejection. It is clear from these
results that a high degree of rain rejection is
available from hoods of moderate size, but that
large hoods are required to reject snow.

Weather Protection
In cold climates, ingestion of large quantities
of snow or fkeezing rain can cause icing of inlet
components. This can adversely affect performance of filtration equipment, and may result in
physical damage to the inlet duct or the gas turbine compressor. In warmer climates, prolonged
downpours may overload inertial separators,
allowing water to be transmitted downstream. If
there are no high-efficiency filters, this will not be
harmful. If there are highefficiency filters, pro
longed wetting will increase the pressure drop
and weaken the filter media structure. .For these
reasons, certain applications may require that the
air filters be preceded by weather protection.
Weather protection, when required, is usually
provided by means of an inlet hood, such as
shown in Fig. 16, or weather louver%. Louvers
may be subject to icing under winter conditions.
Hoods do not have this problem, and have
demonstrated their suitability in both tropical
and arctic climates. Weather hoods achieve
rejection of precipitation by drawing inlet air

Inlet Filter Compartments


Inlet filter compartments are normally elevated in General Electric designs. If only inertial separators are used, this improves air quah-

INLET COMPARTMENT WEATHER HOOD

WEATHER HOOD PENETRATION

Figure 16
9

Figure 18

cal power. An alarm is provided to indicate


that the pressure drop of the inlet filters is
excessive. If corrective action is not taken and
pressure drop rises further, pressure switches
will automatically initiate an orderly shutdown
of the gas turbine. The alarm is a signal to stop
and service wornout filters.
Inlet compartments are typically fabricated
from 3/16 in. steel plate to provide a rigid
structure capable of withstanding severe environmental loadings. Guides for these loadings
are the Uniform Building Code and ANSI
A58.1. A wind force contour of 40 lb./ft.*,
Zone 4 seismic loads, and 40 lb./ft.* snow
loads (as defined by these authorities) are
used as design criteria. Allowable stress levels
are taken from the AISC Steel Construction
Manual. The standard finish is inorganic zinc
primer with a high build epoxy intermediate
coat inside and out. The epoxy serves as a final
coat for the inside while the external surface
will require a final coat after installation.
Because of their size, inlet compartments are
usually shipped in several subassemblies. These
are seal welded in the field to form the complete
structure. Inlet compartments are normally elevated in order to avoid ground-level polhta~~t~.

MULTI-STAGE INLET FILTER


PREFn.lER

ma LFClCHCl

GT21lJ

Figure 19

ty entering the gas turbine; if the compartment uses high-efficiency filters, eIevation prolongs the filter life. A typical arrangement of
an inlet filter compartment using conventional
components is shown in Fig. 19. The entering
air first encounters a bird screen, then the
weather louvres. The access door is just downstream of the weather louvres. Entry is via a
caged ladder and service platform. The compartment includes interior lighting and convenience outlets, and a junction box for electri-

Table 2
Classification of Ambient Air Quality
Air Quality

Clean

Dusty

Contaminated

Desert

Location

Iand Use

Rural

Recreation

Suburban/Urban

Residential

Rural

Agriculture

Urban

Commercial
or Industrial

Seacoast
Dry Lake
Urban

hY
hY
Industrial

Rural
Arid Lands

Agriculture

Description

hY

10

Undeveloped land
Moderate rain
No extended dry season
Continuous ground cover
Light traffic
Mainly single or multiple dwellings
Paved roads, Iight to moderate traffic
Dust-producing activities such as
plowing and harvesting
Stores, warehouses, trucking, mining
construction, manufacturing
Less than 10 miles from salt water
Former seabed in area of low rainfall
Corrosive elements in dust, such as chemicals,
cement, and coal-fired boilers
Also includes areas subject to smoke and fumes
Dust from chemical fertilizers
Little or no rain, extended dry periods

Winds sometimes cause sand or dust storms


with limited (cl mile) visibility

protection is recommended on all units with


high efficiency filtration. Protection can be in
the form of weather hoods and/or rain louvres.
The self cleaning system is inherently protected
by the skirts that extend to a few inches below
the bottom of the filter cartridges.
For several reasons, General Electric does not
recommend that standard, conventional inlet filter compartments be entered when the gas turbine is operating, or that high-efficiency filters
be serviced under this condition. First, the pressure drop of the weather louvres appears across
the compartment access door, holding it closed
with a force of about 120 lbs., although because
of the relative positions of the hinges and the
latch, only about 60 lbs. pull is required to break
the door free. Second, the pressure drop of the
dirty high- efficiency filters tends to hold them
in place against their mounts with a force of
about 50 lbs., which must be overcome by the
service crew, who may be working several feet
above the floor. Third, the filters should be
released and removed in such a way that they do
not dump dust back into the airstream, and this
may not be possible if the crew does not have
special training and supervision.
Compartments with conventional media-type
filters can be designed with special features to
alleviate these problems. However, in most cases
self-cleaning filter compartments offer a solution that is technically and operationally more
satisfactory, and less expensive. General Electric
recommends the use of self-cleaning filters for
all applications where site conditions require
the use of high-efficiency filters and where the
life of these filters is projected to be shorter
than the interval during which continuous operation is required.
In regions subject to sand and dust storms,
such as deserts of North Africa and the Middle
East, most users find it extremely burdensome
to properly maintain conventional media-type
filters because dust loads may become high at
unpredictable times, resulting in very rapid filter consumption. Unless large supplies of spares
and a changeout crew are available at the site,
the frequent result is that the gas turbine operates for a period with the implosion door open,
ingesting unfiltered air during a time when filtration is needed the most or the protective
pressure switches simply initiate a shutdown and
the turbine is taken out of service. Selfcleaning
filters should be used in this type of environ-
mm because they overcome these problems.
The self-cleaning function permits continuous
operation during storm conditions without
operator attention. Filter life is relatively inde-

Recommended Inlet Air Filtration


Design of a system to adequately protect the
gas turbine requires knowledge of ambient air
quality and establishment of criteria for inlet air
quality; the ratio between them defines the
required filter efficiency. Trade-offs can be
made between first cost, maintenance cost, and
gas turbine performance. The following guide
has taken these concerns into account, and gives
recommendations for heavy-duty gas turbines in
nonmarine applications.
Table 2 can be used to classify ambient air
quality at a particular gas turbine site as either
clean, dusty, contaminated, or desert When making judgments, consideration should be taken of
possible future land use as well as current conditions. The gas turbine itself will have negligible
impact on the quality of the air at the site, but
other associated site developments may have an
effect. This is particularly true when the gas turbine is to be part of a larger process or system.
Recommended inlet air filtration can be related to air quality through the use of Table 3.
Self cleaning filters are the standard filtration
means for General Electric heavy-duty gas turbines. If passive filters are required, prefilters
are also recommended if the ambient dust load
is moderately high (> 0.1 ppm by weight), based
upon economic studies which show that this is
to the users benefit.
In addition to the filters described in Table 3,
other devices are needed to supplement conventional filters in special situations. Insect screens
may be required in subarctic, subtropical, and
tropical locations subject to insect swarms. The
user often provides this equipment. Weather
Table 3
Recommended Filtration
Filtration

I
1

Environment 1
Prefdters
Clean

Desert

HighEffIciency

1
1

Self
Cleaning

Passive

1x1

I
11

pendent of ambient dust loading; experience


indicates that two years is typical. Consequently,
filter maintenance can be combined with other
scheduled maintenance in order to increase
availability. The fact that self-cleaning filters
have longer life in the desert than conventional
designs reduces overall maintenance costs. A
major user of gas turbines in Saudi Arabia has
reported that conventional systems cost three
times as much as selfcleaning for replacement
filters and associated labor for changeouts
In cases where there is a question as to the
most appropriate inlet air filtration, General
Electric should be consulted. Site information
and operating experience are available for many
specific locations, worldwide. Where data are
lacking, various services are available to acquire
and analyze ambient air quality and then to prepare recommendations.

LOCATION OF
SAMPLING STATIONS
FOR AIR-BORNE
NATURAL SEA SALT

GT0407c

Figure21
SALT LEVELS INLAND FROM SURF

AIRFILTRA~ON

IN MAARINE
ENVIRONMENTS

WIND SPEED

.l
SALT-rcu

The Marine Environment


Coastal, marine, and off-shore platform installations present unique problems of inlet air contamination, as salt from seawater can become
airborne in significant quantity due to wind and
wave action. As discussed earlier, this can give
rise to corrosion. The sodium concentration at
any given time and place is a function of many
factors, including elevation, wave height, wind
velocity, temperature, humidity, and the previous history of the local air mass.
The salt content of air above or near the sea
can be thought of as being from two sources: the
fine droplets ejected from bursting bubbles, and
the relatively coarse spray from whitecaps and
breaking waves. These two effects are to a degree

.mr

4
s
8
(0
MILES FROM SUM

12

Fiie 22

separable; they can be evaluated by comparing


the salt content of aerosols in which spray was
excluded, and those in which it was not
Figure 20 contains data from many different
investigators showing salt concentration as a
function of wind speed. The data within the
dotted lines were recorded during test conditions in which there was some effort to eliminate
spray effects. Some of the uncertainty arises
from the fact that salt particles can be transmitted over long distances by the wind; local wind
speeds may not be typical of those at the location where the particles were generated.
If the gas turbine intake is subject to salt spray,
as from surf, whitecaps, or the bow-wave of a
ship, the situation can become much more
severe. The measurements by National Gas
Turbine Establishment (NGTE), Jacobs, and
GPU Service Co. are in poor agreement, demonstrating that salt ingestion from spray can vary
over wide limits depending upon wind speed,
wind direction, elevation, distance from surf, and
selfgeneration (as by a ship).
The measurements by GPU Service Co. are
interesting in that they include data at a number

SALT LEVELS VERSUS WIND SPEED

I-

Figure 20

12

SALT CONCENTRATION VARIATION

MASS DISTRIEIUTION VERSUS WIND SPEED


*rn fi.a*.I,

Figure 23

Figure 24

of stations at different distances from the surf


line. As a result, this information can be used to
estimate the dropoff in salt concentration in onshore applications in coastal regions. Fig. 21 is a
map showing the measurement locations.
Station 1 was on the seaward side of a sandy barrier beach. (It is Station 1 data which are shown
in Fig. 20). Station 2 was on the land side of the
barrier beach or the seaward side of the bay,
about a quarter mile from the surf Station 3 was
on the land side of the bay, while subsequent
measuring points were farther inland.
Figure 22 shows data taken during on-shore
winds, plotted in such a way as to emphasize the
rate of decay of salt level with distance. It is obvious that an order-of-magnitude drop is experienced in going from the surf line to the leeward
side of the barrier beach; it can be assumed that
this is due to the fall-out of spray generated by
the waves. If the data from the lee side of the barrier beach are compared to the salt levels shown
in Fig. 20, it is seen that they fall very close to the
dashed line representing the upper limit of the
nonspray data, confirming the assumption that
these data are essentially free of spray effects.
The next measuring station, some 4.25 miles
from the surf, on the land side of the bay, has salt
levels falling well within the limit lines of Fig. 20.
Salt levels continue to decay with distance up to a
range of eight miles; the data at eleven miles
show a small increase for reasons which are not
explained. It is probable that the data at eight to
eleven miles are approaching the natural background level due to non-marine sources, This
supposition is supported by the fact that the
median sodium level in the ambient air as measured by General Electric at 41 domestic gas turbine sites-mostly far inland-was 0.0026 ppm,
which is equivalent to 0.008 ppm sea salt.
If the statistical variation of wind velocity at a
site is known, Fig. 20 can be used to estimate the

salt content of the ambient air. The hours per year


that a given salt level is likely to be exceeded in
the North Sea and the Gulf of Mexico has been
predicted (Fig. 23). The dashed upper limit of salt
concentration (without spray effects) was used in
this calculation. Figure 23 also includes and interpretation of data on sodium levels measured at 30
ft. elevation during winter months in The
Narrows, at the entrance to New York Harbor.*
Salt levels have been deduced by assuming that
the contaminants were 32 percent sodium, as is
typical of sea salt. The measured salt levels are
about half those predicted for the Gulf of Mexico,
which as a similar wind velocity distribution.
When one considers that winds in this protected
harbor will often come from over land rather than
water, this seems reasonable agreement.
The size distribution of marine aerosols as a
function of wind velocity can be estimated from
Fig. 24, which is based upon data published by
Tobag and by the National Gas Turbine
Establishment.io The two references show variations in detail, but similar trends. Part of the
difference lies in the difIiculty of the measurements, but there are also differences in the philosophy of the studies. Toba combined theory
and experiment to define the environment over
the open ocean, while the NGTE information is
based upon shipboard studies. In each case as
wind velocity increases, The droplet size distribution skews toward the larger sizes. Therefore,
wind speed will generally determine the concentration and size distribution of the particles.
Whether salt particles will exist as dry crystals or
saturated droplets will depend primarily on the
relative humidity. If the salt particles start out as
droplet.% as they will at the high humidity present :
at the water/air boundary, they will remain as
supersaturated droplets until the relative humidity
falls to 45 percent or less.11 This is probably due to
the presence of highly soluble magnesium and
13

Most are available either as single- or threestage systems, the use of which depends on the
environment expected (Fig. 26). Single-stage systems typically consist of a series of vertically oriented hooked vanes mounted parallel to the airflow. These vanes impose several direction
changes to the incoming air. Entrained droplets
impinge upon the sides of the vanes, being
unable to follow the air path due to their greater
mass. The effectiveness of such a system is proportional to the velocity of the air stream and
thus to the momentum of the droplets. After
impingement the droplet migrates along the surface of the vane until a hook is encountered. The
solution migrating to the hooks flows down
along the hooks to a catch through and drain
located below the separator.
A three-stage system typically consists of a firststage vane as described above, followed by a coalescer pad and a second vane stage. The coalescer
pad is typically a nonwoven pad approximately 1
in. thick, made from polyester or similar material.
This pad functions to capture smaller droplets
that were not removed in the first stage of the
separator. After capture these droplets may either
drain down through the pad to the catch through
below or agglomerate with other droplets to form
larger droplets which become re-entrained in the
air stream. These agglomerated droplets are cap
tured by the last stage of vanes, which is typically
identical to the first stage.
Figure 27 shows salt penetration through typical single-stage and three-stage moisture separators as a function of windspeed. These penetration curves can be computed by combining
moisture separator collection efficiencies with the
particle size distribution curves of Fig. 24 and the
overall salt content as a function of wind velocity
from Fig. 20. Tobas particle size distribution
curves and the dashed upper limit curve from Fig.
20 were used for these particular calculations.

TEMPERATURE RISE TO OIVE 45% R.H.

*Y-

-*I I.. .

GT04OQ(

Figure 25
MOISTURE SEPARATORS
SINGLE STAGE

+@%%a
AIR FLOW

TRIPLE STAGE

COALESCER PA0

@@fig,,,
MIST EXTRACTOR

12265551

Figure 26
calcium chlorides. Conversely, once the salt is in
crystalline form, it will not deliquesce until the relative humidity rises to about 73 percent,
Since relative humidity in maritime air very
rarely falls below 45 percent, salt will almost
always be present in droplet form. The exception
to this could be gas turbine installations using
anti-icing systems to heat the inlet air. Under the
assumption that the inlet heating system adds
negligible moisture to the air, Fig. 25 shows the
temperature rise required to decrease relative
humidity to 45 percent as a function of ambient
conditions. If the inlet heating schedule has a
temperature rise equal to or greater than that
defined by the appropriate curve, the relative
humidity of the heated air will drop to such levels that salt will exist as dry crystals.

SALT PENETRATION
SPRAY EXCLUDED
SALT
?ENETRATlON.

Equipment for Salt Removal


Several manufacturers offer equipment suitable for the removal of liquid salt from the
incoming air stream. The majority of these systems operate on the same physical mechanism
and differ only in materials and design details.

020400000
WIN0 EFEEO. NW

Figure 27
14

GTO408

Table 4
Experience with High-Velocity Moisture
Separators on GE
Heavy-Duty Gas Turbines

spray and droplets are not encountered. Highefficiency filters were used to remove salt crystals from the inlet air.

ANTI-ICING SYSTEMS

Moisture
Separator
Application

Ships

45

Platforms, Gulf of Mexico I

Platforms,

Others

The operation of gas turbines in cold climates


presents certain unique problems, one of which
is inlet icing. Icing can block inlet filtration
equipment, causing the gas turbine to ingest
unfiltered air or shut down. It can increase the
pressure drop across trash screens and other
inlet components, leading to performance loss
and possible damage to ductwork from implosive forces. In extreme cases, ice can build up on
inlet bellmouths, with hazard of foreign-object
damage and compressor surge. Anti-icing systems are designed to inhibit ice formation on
inlet components in order to protect the gas turbine from these effects and to allow it to operate
reliably in the icing environment.

12

Platforms, North Sea

Arabian

Introduction

1 z&gi 1 Eg- 1

Gulf
I

I
9

1
I

1
I

Experience
Over 75 General Electric heavy-duty gas turbines equipped with single- or three-stage highvelocity moisture separators have been installed
on platforms, ships, or coastal sites.12 These
applications are summarized in Table 4.
Several of the platform. and ship turbines
have accumulated over 40,000 fired hours with
the original buckets and nozzles. Successful
operation is based on the following conditions:
l

Icing Phenomena
Precipitate icing occurs when water is ingested
as a liquid or solid at temperatures near or below
freezing, with wet snow and freezing rain being
obvious examples. If the precipitation remains
suspended in the air-stream, it causes no special
problems. However, ice will adhere strongly to
most surfaces, and buildup can be a particular
problem if the temperature is near freezing.13
If a body of air cools at relatively constant
moisture content, a point is reached at which the
vapor condenses, forming water droplets. This is
the dew point. Further depression of the temperature results in super-cooling of the droplets.
This condition is unstable, so that when droplets
contact an inlet surface, rapid buildup of hoarfrost results. In typical air masses, with many condensation nuclei present, suspended droplets
remain liquid until about -22OF.14
When fuels are burned, both heat and water
vapor are released into the atmosphere. The
heat tends to reduce relative humidity (RH),
while the water vapor tends to increase it.
Typically, the burning of fuel tends to reduce
RH when ambient temperatures are warmer
than about -20F. When colder than about -30F
the burning of fuel increases RH. Between these
limits, a calculation (which includes initial RH)
is required to predict the effect. If weather conditions inhibit mixing of the air, an increase in
RH can give rise to the arctic phenomenon

The number of stages in the moisture separator is a function of the allowable salt ingestion criteria and the expected wind velocities
at the site. North Sea sites have statistically
higher wind velocities than Gulf of Mexico
sites and therefore require three stages
instead of one.
The moisture separators, particularly the
coalescer pads, must be protected from
drilling mud and cement, sandblasting material, and, in some locations, duststorms. This
will prevent frequent changeout of the coalescers due to plugging from these materials.
Prefilters upstream of the separators may be
necessary to remove these contaminants.
Liquid seals on the separator drains must be
maintained so that drainage water will not
be drawn into the compartment downstream of_. the separators.

Turbines at coastal locations have generally


been far enough from the surf line that salt
15

known as ice fog, in which the atmosphere is


supersaturated with respect to ice.14
While icing generally occurs on the first
obstacle encountered by air entering an inlet
system, typically a trash screen or a filter, it is
possible for ice to form on the inlet bellmouth
of the gas turbine without forming on other
upstream components. This phenomenon is
explained by the isentropic acceleration of the
air as it enters the bellmouth, which results in
cooling. While much of this temperature depression is recovered at surfaces such as the bearing
support struts or inlet guide vanes, these surfaces can still be several degrees cooler than
ambient. The calculated wall temperature
depression at the inlet guide vanes of the
LM2500 is 3.5OF, while the corresponding value
for heavy-duty machines is 2.4F. This temperature depression can cause local icing in the bellmouth if the air is sufficiently moist. Ice formation in the bellmouth could reduce the surge
margin of the compressor, and if chunks of ice
break off and enter the engine, foreign object
damage may occur. Heavy-duty gas turbines are
more tolerant of the bellmouth icing than are
aircraft-derivative engines due to their lesser
temperature depression, heavier compressor
blading, and greater surge margin.

INLET SYSTEM WITH INLET HEATING

Figure 28
even if the screen ices because of cold air being
drawn through any leaks in the ductwork.
Finally, another pressure alarm can be located
in the inlet plenum. If desired, this switch can
be used to initiate a controlled shutdown when
the pressure drop of the total inlet system reaches a predetermined level.
Ingestion of snow and freezing rain into the
inlet should be minimized in order to make the
job of the anti-icing system easier, particularly in
the near-freezing temperature range. One way
that this is done is by elevating the inlet filter
compartment. Studies show that the flux of
blowing snow drops by a factor of about 5 when
going from an elevation of 5 to 25 ft.15 There is
little benefit in further elevation because winddriven snow tends to be concentrated near
ground level. Ingestion of rain and snow is also
minimized by use of a properly designed weather hood if conventional filtration is to be used.

Protective Features
Inlet systems for cold climates are designed to
protect the gas turbine from damage due to
icing and to keep the machine running with
minimum effect on performance. Typical
designs include self cleaning filters which can
remove ice in much the same way that they
remove dust, an inlet heating system to inhibit
ice formation downstream of the filters, and
protective devices to prevent damage in the
event of system malfunction or operation outside the normal design envelope. These features
are illustrated in Fig. 28 which shows the side
elevation of an inlet system.
The anti-icing module contains the inlet heating manifold, which introduces warm air downstream of the self cleaning filters in the inlet
duct. If there is icing on the inlet filters, a pressure switch which senses increasing pressure
drop, initiates the self cleaning system. An alarm
is signalled if pressure drop continues to
increase. If no action is taken by the operator, a
gas turbine shutdown is signalled by the inlet
protective pressure switches. The split trash
screen in the inlet duct protects against ingestion of ice as well as trash. Its design is such that
it can pass air without excessive pressure drop,

Self-Cleaning Filters
Experience shows that selfcleaning filter cartridges can remove hoarfrost in much the same
way that they clean themselves of dust. Tests
SELF-CLEANING INLET FILTER

GTO6807

Figure 29
16

because of its anti-icing capability. It has also


become the favored system throughout Canada
for the same reason.

have been conducted by filter vendors to simulate precipitate icing by spraying water from fog
nozzles under winter conditions. These tests
have demonstrated that, although ice can be
built up on filters, the porosity of this ice is typically so high that the drop in filter pressure stays
within acceptable limits. A frost point detector
may be used to signal the selfcleaning system to
begin pulsing when icing conditions are present. This helps alleviate any potential problems
associated with a buildup of ice on the filters by
removing it as soon as it begins to form.
The unanswered key question was whether
there would be ice formation in the gas turbine
inlet bellmouth due to the temperature depression which occurs there. To study this, extensive
tests were run on an LM2500 gas turbine in
western Canada during the 1981-82 winter (Fig.
29). This machine, which has a self-cleaning
inlet air filter with no inlet heating, had already
completed a full year of successful operation
before the test.
During the test, which covered an additional
2700 fired hours of winter operation, a data logger recorded ambient and inlet temperature
and humidity, pressure drop, and engine performance parameters at lo-minute intervals. In
addition, time-lapse video tape recordings were
made through viewing ports in the inlet plenum
in order to visually identify any ice in the bellmouth. During the test period, frequent intervals of high humidity at below-freezing temperatures were recorded. Frost was visible on the
inlet guide vanes for one period of less than a
minute, but there was no ice build-up, and no
icing problems were experienced.
Two trends can be seen which help to explain
these favorable results. First, when ambient air is
supersaturated with respect to ice, air downstream of the filters is found to be just at the
frost point, indicating that frost is forming on
the outside of the filter elements. Moisture
which freezes on the filters is obviously no
longer available to cause problems at the bellmouth. If too much frost builds up on the filters, it is removed by the self-cleaning action.
Second, temperatures in the inlet bellmouth
run about 2 to 3F warmer than air leaving the
filter compartment, even though there is no
inlet heating system. This heating, which tends
to counteract temperature depression, is apparently due to a combination of radiation and conduction from hot parts of the engine.
Numerous gas turbine installations now use
self-cleaning filters as an anti-icing system. The
self-cleaning filter has become the standard
inlet filtration system at Prudhoe Bay, Alaska

Inlet Heating Systems


Most General Electric inlet heating systems
are operated by mixing hot gas from some
source with cold, ambient air at the entrance to
the inlet system. The hot gas has always been air
(or air plus some combustion products); so the
temperature rise can be calculated by a simple
heat balance:
W hot = W mixed

Tmixed - Tambien t
Thot - Tambient

where
w = Weight flow per unit time
T= Temperature
Early inlet heating systems included exhaust
recirculation, exhaust heat recovery, and cornpressor bleed recirculation designs. These systerns were used to prevent ice buildup both on
the inlet filters and in the ducting and compressor. With the advent of the self-cleaning filter,
and its inherent anti-icing ability, inlet heating is
used today mainly in areas where compressor
icing is of potential concern.
Of the previously mentioned inlet heating
systems, only the compressor bleed system is
typically used today. This is due to the relative
simplicity of the system and its less costly effects
on turbine performance.

Compressor Bleed Inlet Heating


A compressor bleed inlet heating system uses
a portion of the compressor discharge air for
heating
(Fig. 30). As a result of com. the
,. inlet air
_.
presslve forces, this air typically has a temperature of 500 to 75OF, depending upon the ambiCOMPRESSOR

BLEED INLET

HEATING

GT2113j

Figure 30
17

anti-icing, the simplicity of the concept and its


minimal effect on performance make it particularly attractive to the user. For applications
where supplimental inlet heating is required to
prevent icing in the compressor bel,lmouth,.
Fompressor bleed inlet heating is recommended. This is based on a balance of cost, reliability,
and impact on performance.

FROST POINT SENSOR


LED

PHOTO TRANSISTOR

TEMP SENSOR

INLET COOLING SYSTEMS


Introduction
An inlet cooling system is a useful gas turbine
option for applications where significant operation occurs in the warm months and where low
relative humidities are common. The cooled air,
being denser, gives the machine a higher massflow rate and pressure ratio, resulting in an
increase in turbine output and efficiency. This is
a cost-effective way to add machine capacity during the period when peaking power periods are
usually encountered on electric utility systems.
There are two basic systems currently available
for inlet cooling. First, and perhaps the most
widely accepted system is the evaporative cooler.
Evaporative coolers make use of the evaporation
of water to affect a reduction in inlet air temperature. Another system currently being studied is
the inlet chiller. This system is basically a heat
exchanger through which the cooling medium
(usually chilled water) flows and removes heat
from the inlet air thereby reducing the inlet temperature and increasing gas turbine output.
In addition to the obvious advantage of
achieving extra power, the use of an evaporative
cooler improves the environmental impact of
the machine. Increasing water vapor in the inlet
air tends to lower the amount of oxides of nitrogen produced in the combustion process and,
therefore, lowers the emissions of the machine.

Figure 31
ent temperature and the gas turbine model. The
system is basically quite simple, since only one
control valve is required. Because of its simplicity, the reliability has been excellent in Alaska
and Canada, as well as the North Sea.
While the compressor bleed system is simple
and reliable, there is some performance degradation due to the compressor bleed requirement. This can be minimized by heating only
the minimum amount necessary to keep all
parts of the inlet system at a relative humidity
below the frost point. This determination cannot be made on the basis of temperature alone.
What is needed is a device which can measure
the potential for icing, so that a control can be
designed which causes the air to be heated just
enough, but no more.
The key to the solution of this problem is a sensor which measures the moisture content of the
air. Such a device is shown in Fig. 31. A beam from
a lightemitting diode is reflected onto a phototransistor from the polished surface of an electrically cooled plate. The plate is cooled to the point
where dew or frost just begins to deposit, interrupting the beam. Its temperature is measured,
and the difference between this temperature and
the air temperature defines the potential for condensate icing. This device measures absolute
humidity, avoiding the problems inherent in relative humidity sensors and lending itself well to
optional inclusion in a control system.

COOCINti

PSY

Recommendations
Good experience with self-cleaning filters for
both inlet air filtration and anti-icing has made
it the standard system in environments with a
high icing potential. There is no question that
self-cleaning filters provide very high air quality;
thousands of hours of desert operation have
demonstrated this conclusively. As a means of

00

60

60

100

D R Y BUl.B T E M P E R A T U R E F

Figure 32
18

120

TC23564
1732566

channels, and diffuses throughout the media by


wicking action. any excess returns to the tank.
The level of water in the tank is maintained by a
float valve which admits make-up water.
The ambient temperature setpoint (located at
the cooler controller) is adjustable. It is factory
preset to allow cooler operation at ambients
above the setpoint, which must be 60F or higher.
If evaporation were permitted at too low a temperature, there would be a possibility of causing
icing which is of course to be avoided. When
there is a possibility that the dry-bulb temperature will fall below freezing, the whole system
must be deactivated and drained to avoid damage
to the tank and piping, and to avoid the possibility that the porous media would plug with ice.

Evaporative Cooler Theory


The actual temperature drop realized is a
function of both the equipment design and
atmospheric conditions. The design controls the
effectiveness of the cooler, defined as follows:
Cooler effectiveness =

TIDB - T2WB
TlDB-T2WB

Subscript 1 refers to entering conditions


and 2 to the exit; DB means dry-bulb temperature and WB means wet-bulb. The effectiveness of General Electric evaporative coolers is
typically 85 percent; so the temperature drop
can be calculated by:
ATDB = 0.85 (TIDB - TIWB)

Water Requirements

As an example, assume that the ambient


temperature is lOOoF and the relative humidity
is 32 percent. Referring to Fig. 32, which is a
simplified psychrometric chart, the corresponding wet-bulb temperature is 75F. The
temperature drop through the cooler is then
0.85 (100-75)) or 21F. The cooling process follows a line of constant enthalpy as sensible heat
is traded for latent heat by evaporation.
The current self-cleaning filter/evaporative
cooler design is shown in Fig. 33. Water is
pumped from a tank at the bottom of the module to a header which distributes it over the
media blocks. These are made of corrugated layers of fibrous material, with internal channels
formed between layers. There are two alternating sets of channels, one for water and one for
air. This separation of flows is the key to reducing carry-over. However it is standard practice at
General Electric to provide a stage of drift eliminators downstream of the media to protect
against the possibility of water carry-over. The
water flows down by gravity through the water

Evaporative coolers find their greatest application in arid regions. In such areas it is not uncommon to find that available water has a significant
percentage of dissolved solids. If make-up water is
only added in sufficient quantity to replace the
water which has been evaporated, it is obvious
that the water in the tank (which is also the water
pumped to the media for evaporation) must
gradually become more laden with minerals. In
time, these will tend to precipitate out on the
media and reduce evaporation efficiency, and the
hazard increases that some minerals will become
entrained in the air and enter the gas turbine. In
order to minimize this it is usual to continually
bleed some water from the tank to keep the mineral content diluted. This is termed blowdown.
The total amount of water which must be provided as make-up is the sum of evaporation and blowdown. The rate at which water evaporates from a
cooler depends upon the ambient temperature
ad humidity, the altitude, cooler effectiveness, and
the airflow requirement of the gas turbine. The

EVAPORATION RATE FOR MS6001


85% EFFECTIVENESS
EVAP~F~ATION. GPM

MEDIA PACK
COOLER
DESIGN

20 ,

80
90
TEMP - F

1W

110

120
GT2114

Figure 33

Figure 34
19

lied Langlier saturation index chart is used (see


Fig. 35). The adjusted total alkalinity (ppm as
CaCOs) is converted to PALE, and the adjusted
total hardness (ppm as CaCOs) is converted to
PCA by entering the chart on the righthand
ordinate and reading the appropriate quantity
from the righthand abscissa. The adjusted total
dissolved solids are converted to PTDS by entering the left ordinate, selecting the appropriate
water temperature (which may be taken to be
the wet bulb temperature), and reading the
upper left abscissa.

evaporative requirement of an 85 percent effective


MS8001 gas turbine cooler at sea-level is shown in
Fig. 34. The corresponding value for an MS7001 or
MS9001 machine may be estimated by respectively
doubling or tripling the quantity shown.
One of the main concerns in determining the
acceptability of water quality is its propensity to
deposit scale. Scaling is influenced by the interaction of the waters total hardness, total alkalinity
(ALK), total dissolved solids (TDS), pH and water
temperature. To assist in determining whether the
available water is suitable for use in General Electric
evaporative coolers, a saturation index (SI) is used.
A standard laboratory analysis of the water
can determine the total hardness (ppm as
CaCOs), total alkalinity (ppm as CaCOs), total
dissolved solids (ppm) and pH. The levels of the
first three components are first modified by an
adjustment factor W:

Saturation Index (SI) = pH - PCA - PALK PTDS


SI < 1.0 indicates no water treatment is
required.
Water treatment may be used to control any
property or combination of properties to reduce
SI to 1.0 or less. Initially, the blowdown rate is
adjusted to be approximately the same as the
evaporation rate on a typical hot day; this may
later be adjusted based on operational experience and local water quality.
Despite care with water quality, the media will
eventually have to be replaced as material precipitates out in sufficient quantity to impair its effectiveness. However, experience indicates that this
may take quite a long time. At one site there has
been operation for six seasons under very adverse
conditions with insignificant performance degradation. It is expected that the media will continue
to be used for at least two more years. While this
is believed typical, the estimate is subject to
change as more experience is gained.
Tests indicate that the feedwater may have
high levels of sodium and potassium without significant carry-over of these metals into the gas
turbine. However, very careful attention to
detail is necessary in order to realize this level of
performance. This includes proper orientation
of the media packs, correct flows of air and
water, uniform distribution of water over the
media surface, and proper drainage back to the
tank. Any deficiencies in these areas may make it
possible for water to become entrained in the
air, w i t h p o t e n t i a l l y s e r i o u s r e s u l t s .
Consequently, installation and maintenance of
evaporative cooling equipment is very important. In areas where the water exceeds 133 ppm
sodium and potassium it is good practice to per-i- :
odicahy check the rate at which these elements
enter the gas turbine by means of a mass-balante calculation. Any discrepancy between the
rate at which sodium and potassium enter in the

W=(%+l) (%+l)
where
F

flood
factor

water drain rate


from media to tan
water evaporation rate

water bleed rate


from tank
water evaporation rate
Water evaporation rate can be estimated from
Fig. 34.
For most cases F and B are adjusted during
installation to be approximately uniform on a
typical hot day so W = 4. However, to make lowquality water more suitable, an increased blowdown rate may be used to lower the adjustment
factor. Flood factor should not be adjusted to
compensate for water quality since this could
result in liquid water carry-over.
The ppm of TDS, ALK, and hardness are multiplied by the adjustment factor to obtain ppm
(adjusted). To evaluate the suitability of water
for General Electric evaporative coolers, a modiB =

blowdown =
factor

LANGELIER SATURATION INDEX CHART

Figure 35
20

Inlet Cooling Coils

feedwater and the rate at which they leave in the


blowdown can be attributed to carry-over. It will
be recalled that the concentration of these elements in the inlet air should typically be held to
0.005 ppm or less; this is equivalent to an ingestion rate of 0.01 lb./h. for an MS7001 gas turbine, 0.005 lb./h. for an MS5000, and 0.0002
lb./h. for an MS3002.

When medium-type coolers were first placed


in service, some units exhibited unacceptable
carry-over. It was found that this problem had
three possible causes: damaged or improperly
installed media, entrainment of water from the
distribution manifold, or local areas of excessive velocity through the media. The first cause
was removed by new procedures for shipping
and installing the media blocks. Carry-over
from the manifold was eliminated by installation of blanking plates downstream of the spray
elements. The third problem, high flow velocity through portions of the media, was the most
difficult to solve. After considerable effort, two
solutions were developed. The first incorporated features in the design to force more uniform flow, so that velocities everywhere were
within the acceptable range. The second solution was more radical. It involved a new design
which accepted some carry-over from the
media, but which eliminated carry-over into
the gas turbine by use of eliminator blades
(similar to the vanes of a moisture separator)
immediately downstream of the evaporative
media. Both approaches have proven successful
in the field and both approaches are now taken
together to ensure no water carry-over. There
has been no problem in meeting goals for cooler effectiveness in any of the more than 75
media-type coolers now in the field.

AS with the evaporative cooler, the actual


temperature reduction from a cooling coil is a
function of equipment design and ambient
conditions. Unlike the evaporative cooler, however, cooling coils are able to lower the inlet
dry bulb temperature below the ambient wet
bulb temperature. The actual temperature
reduction is limited only by the capacity of the
chilling device, the effectivness of the coils, and
the acceptable temperature/humidity limits of
the compressor.
Figure 36 shows a typical cooling cycle based
on an ambient dry bulb temperature of ZOOOF
and 20 percent relative humidity. Initial cooling
follows a line of constant humidity ratio. As the
air approaches saturation, moisture begins to
condense out of the air. If the air is cooled further, more moisture condenses. Once the ternperature reaches this regime, more and more of
the heat removed from the air is used to condense the water. This leaves less capacity for temperature reduction. Because of the potential for
water condensation, General Electric recommends that drift eliminators be installed downstream of the coils to prevent excessive water
ingestion by the gas turbine. The exact point at
which further cooling is no longer feasable
depends upon the desired gas turbine output
and the capacity of the chilling system.
It is readily apparent in Fig. 36 that the air
can easily be cooled below the ambient wet
bulb temperature. Therein lies one of the
major benefits of the cooling coil system. It
must be pointed out, though, that the lower
limit of cooler operation is a compressor inlet
temperature of 45OF with a relative humidity of
95 percent. At temperatures below 45F with
such high relative humidity, icing of the compressor is probable.

INLET CHILLING PROCESS

EFFECT OF EVAPORATIVE COOLER ON AVAILABLE OUTPUT

Operational Experience

85% EFFECTIVE
;:TE/\SE
,,o~
IN OUTPUT - X

RH-

2Qx

12 -

30x
40x
50%
60%

DRYsu.BTEMPERATUREr

TEMP - F

GT21141

Figure 36

Figure 37
21

5. Artifical Stimulation of Rain, Geophysics


Research Directorate, Air Force Cambridge
Research Center and Geophysics Branch,
Office of Naval Research, Pergamon Press,
NY, 1957, p. 163.

Power Increase
The exact increase in power available from a
particular gas turbine as a result of inlet air cooling depends upon the machine model and site
altitude as well as ambient temperature and
humidity. However, Fig. 37 can be used to make
an estimate of this benefit for evaporative coolers. As would be anticipated, the improvement is
greatest in hot, dry weather. The power increase
from a cooling coil is also dependent upon the
chiller capacity so it is difficult to make a general estimation. The addition of an inlet cooler is
economically viable when the value of the
increased output exceeds the initial and operating costs, and appropriate climatic conditions
permit effective utilization of the equipment.

6. Anderson, A.W. and Neaman, R.G., Field


Experience with Pulse-Jet Self-Cleaning Air
Filtration on Gas Turbines in a Desert
Environment, ASME Paper 82-GT-283.
7. Tatge, R.B., Gordon, C.R., and Conkey, R-S.,
Gas Turbine Inlet Air Filtration in Marine
Environments-Part I: Marine Aerosols and
Equipment for Their Control, ASME Paper
8O-GT-174.
8. Krulls, G.E. and Lastella, J., Gas Turbine Salt
Ingestion Analysis.* ASME Paper 77GT20.

SUMMARY

9. Toba, Y, On the Giant SeaSalt Particles in


the Atmosphere, Tellus, Vol. 17, NO. 1,
1965, pp. 131-145.

It has been shown that there are many environments which are naturally hostile to gas turbine operation, but that General Electric has
developed a wide range of inlet air treatment
equipment which permits its machines to adapt
to these conditions and operate successfully.
With the information given in this paper, it is
hoped that gas turbine users will be able to identify potential needs for air treatment, and to
knowledgeably consider equipment options.
General Electric applications engineers have
many years of experience in this field and are
ready to assist in selection of suitably equipped
inlet compartments to enhance gas turbine performance, reliability, and maintainability.

10. Randles, R.H. and Ansari, F., Evaluation of


the Peerless Mark 1 Spray Eliminator for
Protection of Marine Gas Turbine Air
Intakes, Naval Marine Wing Note No.
30/71, National Gas Turbine Establishment,
Pyestock, Hams, England.
11. Jungle, C.E., ed., Aerosols, Air Chemistry
;I 2ytioactivity, Academic Press, 1963, pp.
12. Tatge, RB., Gordon, C.R., and Conkey, R.S.,
Gas Turbine Inlet Air Filtration in Marine
Environments-Part II: Commercial Experience and Recommended Practice, ASME
Paper 8@GT-175.

REFERENCES
1. Beltran, A.M., and Shores, D.A., Hot
Corrosion, Chapter 11 from Superalloys,
C.T. Sims and W.C. Hagel, eds., John Wiley
and Sons, 1972.

13. Chappell, M.S. Stationary Gas Turbine Icing


Problems: The Icing Environment, National
Research Council, Ottawa, Canada, January
1973.

2. Fairman, L., Mechanism of Accelerated


Oxidation by Vanadium-Containing Fuel
Ash, Corrosion Science, Vol. 2 1962, pp.
293-296.

14. Appelman, H., Ihe Cause and Forecasting


of Ice Fogs, Bull. Am. Meteorological SOc.,
Vol. 34, No. 9, November 1953.

3. Bradury, B.J. Hancock, P., and Lewis H.,


The Corrosion of Nickel-Base Material in
Gas Turbine and Boiler Atmospheres,
Metallurgia, January 1963. pp. 3-14.

15. Grabe, W. and Chappell, M.S. Stationary


Gas Turbine Icing Some Design Guidelines
for Blowing Snow Environments, National
Research Council, Ottawa, Canada,
September 1974.

4. Air Quality Data-1978 Annual Statistics,


EPA-450/4-79-037, U.S. Environmental
Protection Agency, Research Triangle Park,
North Carolina.

Q 1991 GE Company
22

>

CONVERSION FACTORS
The following is a list Of COWerSiOn factors most
commonly used for gas turbine performance.

To

Convert

acres
atm
atm
bars
bars
Btu
Btu
Btu/h
Btulh
Btu/h
Btulhp-h
Btulhp-h
BtulkWh
BtulkWh
Btullb
Btullb
C
C
cm3
cm3
F
ft
ft*
fta
fts
ft-lb
ft-lb
ftlmin
ft3/min
ft3!min
gal
gallmin
hectares
hp (U.S.)

To

Multiply By

To

hectares
kg/cm*
lb/in.*
atm
lb/in.*
J (joules)
kcal
kcallh
kJlh
W (watts)
kcal/kWh
kJlkWh
kcal/kWh
kJlkWh
kcallkg
kJlkg
F
K
ft3
in.3
C
m
m*
I (liters)
m3
Btu
kg-m
km/h
I/s
m3/min
m3
I/s
acres
kW

4.047 x 10
1.0333
1.47 x 10
9.869 X 10-l
1.45 x 10
1.055 x lo3
2.52 x 10
2.520 x 10-l
1.0548
2.931 x 10
3.379 x 10
1.4148
2.5198 x 10-l
1.0548
5.555 x 10
2.3256
(C x 915) + 32
C + 273.18
3.531 x 10~
6.102 x lo-*
(F-32) x 519
3.048 x 10
9.29 x 10-2
2.832 x 10
2.832 x lo-*
1.286 x 1O-3
1.383 x 10-l
1.8288 x lo-*
4.720 x 10-l
2.832 x lo-*
3.785 x 1O-3
6.308 x lo-*
2.471
7.457 x 10

To

Multlply By

hp (U.S.)
in.
in.
in.2
in. of mercury

hp (metric)
cm
mm
mm*
kg/cm*

1.014
.
2.540
.
2.54 x 10
6.452 x lo*
3.453 x lo-*

in. of water
(at 4C)

kg/cm*

2.54 x 1O-3

in. of water
(at 4X)

lb/in.*

3.613 x lo-*

Convert

Btu
lb
kg
kg/cm*
lb/in.*
kg-m
ft-lb
kg/m3
lb/f@
km
miles (statute)
kW
hp
I
fts
lb
kg
lb/In.*
kg/cm*
lb/in.*
Pa
lb-ft*
kg-m*
llmin
ftsls
llmin
galls
m
ft
m*
ft*
m3
fts
mile (statute) km
tons (metric) kg
tons (metric). lb
W
Btulh
W
Btulmin
W
ft-I b/s
W
hp

9.486 x 1O-4
2.2046
1.422 x 10
7.233
6.243 x lo-*
6.214 x 10
1.341
3.531 x 10-2
4.536 x 10
7.03 x lo-*
6.8948 x lo3
4.214 x 10-l
5.886 x 1O-4
4.403 x 1o-3
3.281
1.076 x 10
3.531 x 10
1.6093
1.0 x lo3
2.205 x lo3
3.4129
5.688 x lo-*
7.378 x lo-
1.341 x,10-s

For further information, contact your GE Field


Repres&tative or write to GE CommunicatiDn Programs

GE Industrial &
Power,Systems \
General Electric Company
Building 2, Room 1158
one River Road
One
Schenectady, NY 12345

6/91(2Mb

You might also like