Chapter 5 PDF

Chapter 5
The Finite Volume Method for

Convection-Diffusion Problems
Prepared by: Prof. Dr. I. Sezai

Eastern Mediterranean University
Mechanical Engineering Department
Introduction
The steady convection-diffusion equation is
div( u ) = div(grad ) + S
Integration over the control volume gives :
n ( u)dA = n (grad )dA + S dV

A
CV
This equation represents the flux balance in a control volume.

The main problem in the discretisation of the convective terms is the
calculation of at CV faces and its convective flux across these
boundaries.
Diffusion process affects the distribution of in all directions.
Convection spreads influence only in the flow direction. This sets a
limit on the grid size for stable convection-diffusion calculations with
central difference method.
ME555 : Computational Fluid Dynamics
I. Sezai - Eastern Mediterranean University
Steady one-dimensional convection and diffusion

In the absence of sources, the steady convection and diffusion of a
property in a given one-dimensional flow field u is governed by
d
d
d
( u ) = ( )
dx
dx dx
(5.3)
The flow must also satisfy continuity, so

d
( u) = 0
dx
Integrating Eqn. (5.3) over the CV

( uA )e ( uA ) w = A A
x
x w
(5.5)
Integrating continuity Eqn.

( uA)e ( uA) w = 0
(5.6)
3
Let F = uA convective mass flux

at cell faces
D = A/x diffusion conductance
At cell faces:
Fw = ( uA) w
Fe = ( uA)e
Dw =
w Aw
xWP
De =
e Ae
xPE
Using central difference approach for the diffusion terms, Eqn (5.5)
becomes
Fee Fww = De (E P ) Dw (P W )
(5.9)
C i i equation
Continuity
i becomes
b
Fe Fw = 0
We assume that velocity field is known Fe, Fw known.

We need to calculate at faces e and w.
(5.10)
The Central Differencing Scheme

Works well for diffusion terms.
Let us use this method to compute the convective terms by
linear interpolation.
For a uniform grid, cell face values are:
e = (P + E ) / 2
w = (W + P ) / 2
Substituting into eqn (5.9)
Fe
F
(P + E ) w (W + P ) = De (E P ) Dw (P W )
2
2
Rearranging,
Fw
Fe
Fw
Fe
Dw 2 + De + 2 P = Dw + 2 W + De 2 E

Fw
Fe
Fw
Fe
Dw + 2 + De 2 + ( Fe Fw ) P = Dw + 2 W + De 2 E

which is of the form

aPP = aW W + aEE
(5.14)
where
aW
Dw +
aE
Fw
2
De
aP
Fe
2
aW + aE + ( Fe Fw )
This equation has the same general form as the diffusion eqn. (4.11).
Example 5.1
A property is transported by convection and diffusion through the
one dimensional domain shown below. Using central difference
scheme, find the distribution of for (L =1,
1, = 1, = 0.1)
(i) Case 1: u = 0.1 m/s (use 5 CVs)
(ii) Case 2: u = 2.5 m/s (use 5 CVs)
Compare the results with the analytical solution.
o exp( ux / ) 1
=
L o exp( uL / ) 1
(iii) Case 3: u = 2.5 m/s (20 CVs)
The governing equation is:

A
1
=1
d
d d
( u ) =
dx
dx dx
4
w
e
5
x/2
B
7
=0
xWP= x xPE=x
x/2
aPP = aW W + aEE + Su
where
aP = aW + aE + ( Fe Fw ) S P
Fw = ( uA) w
Dw =
w Aw
xWP
Fe = ( uA)e
De =
For interior nodes: xWP = xPE = x

For node 2: xWP = x / 2
For node 6: xPE = x / 2
e Ae
xPE
Node
aW
aE
SP
Su
2
0
De Fe / 2 ( Dw + Fw / 2) ( Dw + Fw / 2) A
3, 4,5 Dw + Fw / 2 De Fe / 2
0
0
6
0
( De Fe / 2) ( De Fe / 2)B
Dw + Fw / 2
The resulting system of equations are

aP2
aW3
aE 2
a p3
aE 3
aW4
a p4
aE 4
aWi
a pi
aE i
aWn2
a pn 2
aWn1

Su2
2
3
Su3
4 Su4

Su
i
i

Su
aE n 2 n 2
n2
a pn1 n 1 Sun 1
Solve the system of equations using Tri-diagonal matrix algorithm

(TDMA) for 2, 3, 4, n-1 , where (n = 7)
The solution for case 1 is:

1 1
0.9421
2
3 0.8006

4 = 0.6276
5 0.4163

6 0.1573
0
Exact solution is:
( x) =
2.7183 exp( x)
1.7183
Comparison of the numerical result with the

analytical solution.
10
The solution for case 2: (u = 2.5 m/s, 5 CVs)
Comparison of the numerical result with the analytical solution.
The solution appears to oscillate about the exact solution.

11
The solution for case 3: (u = 2.5 m/s, 20 CVs)
Comparison of the numerical result with the analytical solution.
Grid refinement has reduced the F/D ratio from 5 to 1.25.

Central difference scheme yields accurate results when F/D ratio is low.
12
Properties of Discretisation Schemes

The numerical results will only be physically
realistic when the discretisation scheme has certain
fundamental properties. The most important ones
are:
Conservativeness
Boundednes
Transportiveness
13
1. Conservativeness
To ensure conservation of for the whole solution
domain the flux of leaving a CV across a certain
face must be equal to the flux of entering the
face
adjacent CV through the same face.
To achieve this the flux through a common face
must be represented in a consistent manner (by one
and the same expression) in adjacent CVs.
14
Example of consistent specification of diffusive fluxes
w 2 (2 1 )
x
Flux entering CV 2
e 2 (3 2 )
x
Flux leaving CV 2
An overall flux balance may be obtained by summing the net flux through each CV
(3 2 )
(2 1 )
(2 1 )

e1 x q A + e 2 x w 2 x
(4 3 )
(3 2 )
(4 3 )
+ e3
w3
+ q w4
= q q
x
x B
x B A
e1 = w2, e2 = w3 and e3 = w4 Fluxes across CV faces are

expressed in consistent manner,
fluxes cancel out in pairs when summed over the entire domain.
15
Flux Consistency ensures conservation of over the entire domain

for the central difference formulation of the diffusive flux.
Inconsistent flux interpolation formulae give rise to unsuitable
schemes that do not satisfy overall conservation.
For nodes 1, 2 and 3 quadratic function 1 is used.

For nodes 2, 3 and 4 quadratic function 2 is used.
If gradient of 1 gradient of 2 at cell face flux leaving CV 2 will
not be equal to flux entering CV 3
overall conservation is not satisfied.
16
2) Boundedness
The sufficient condition for a convergent iterative method is
nb
aP
1 at all nodes
< 1 at one node at least
aP = aP S p
(5.22)
If eqn. (5.22) is satisfied, resulting matrix coefficients are diagonally

dominant.
For diagonal dominance, (aP Sp) should be large and Sp < 0.
Diagonal dominance is a desirable feature for satisfying the boundedness
criterion.
This states that in the absence of sources the internal nodal values of
should be bounded by its boundary values.
In a steady conduction problem without sources for which the boundary
temperatures are 200 and 500 oC, all interior values of T should be between
these temperatures.
17
Another essential requirement for boundedness is that all coefficients

of the discretised equations should have the same sign.
If the discretisation scheme does not satisfy the boundedness criteria
the solution may not converge at all.
all Or if it converges it will contain
wiggles. (See case 2 of Example 5.1). In case 2 most of the aE values
were negative (Table 5.3).
Table 5.3
Node
2
3
4
5
6
aE = De
Fe e Ae ue Ae
=
2 xPE
2
18
3) Transportiveness
The transportiveness property of a fluid flow can be illustrated by
considering a constant source of at a point P
u
F
cell Peclet number
Pe = =
D / x
Distribution of in the vicinity

of a source at different Peclet
numbers.
Lines represent contours of constant .

For no convection and pure diffusion Pe = 0
For no diffusion and pure convection Pe , E = P E is
influenced only by P.
19
Assesment of the Central Differencing Scheme for Convection

Diffusion Problems
Conservativeness
The central differencing scheme uses
consistent expressions to evaluate convective
and diffusive fluxes at the CV faces.
The scheme is conservative.
20
10
Boundedness
(i) The internal coefficients of discretised scalar transport equation
(5.14) are
aW
Dw +
aE
Fw
2
De
aP
Fe
2
aW + aE + ( Fe Fw )
(Fe Fw) = 0 from continuity aP = aW + aE

Thus, convergence criteria (5.22) is satisfied by the central difference
scheme
scheme.
In the example of section 5.3:
For case 2: Pe = 5 oscillatory
For case 1 and 3: Pe < 2
21
(ii) aE = De Fe/2
For aE > 0
or
Fe
< De
2
Fe
= Pee < 2
De
to have positive aE .
If Pe > 2 CD scheme violates boundedness

gives physically unrealistic solutions.
22
11
Transportiveness
The CD scheme does not recognise the direction of the
flow or the strength of convection relative to diffusion.
Thus it does not posses the transportiveness property at
Thus,
high Pe.
Accuracy
The CD scheme is stable and accurate only if Pe = F/D <
2.
The CD scheme satisfies this criteria for low Re numbers
or for small grid spacings.
Thus, CD scheme is not a suitable discretisation practice
for general purpose flow calculations.
23
5.6 The upwind differencing scheme

The scheme takes into account the flow direction, at cell face = at upstream
node formulation is used
When the flow is in the positive direction, uw>0, ue>0 (Fw>0, Fe>0), the
upwind scheme sets w = W and e = P
(5.25)
24
12
The discretised equation (5.9) becomes

FeP Fww = De (E P ) Dw (P W )
(5.26)
Which can be rearranged as

( Dw + De + Fe ) P = ( Dw + Fw ) W + DeE
to give
( Dw + Fw ) + De + ( Fe Fw ) P = ( Dw + Fw ) W + DeE
(5.27)
When the flow is in the negative direction, uw<0, ue<0 (Fw<0, Fe<0), the
scheme takes
w = P and e = E
(5.28)
Now the discretised euqation is
(5.29)
FeE FwP = De (E P ) Dw (P W )
or
Dw + ( De Fe ) + ( Fe Fw ) P = DwW + ( De Fe )E
25
(5.30)
the equations (5.27) and (5.30) can be written in the usual general
form
aPP = aW W + aEE
(5.31)
with central coefficient
aP = aW + aE + ( Fe Fw )
and neighbour coeffcients
aw
ae
Fw>0, Fe>0
Dw + Fw
De
Fw<0,
Dw
De - Fe
<0 Fe<0
A form of notation for neighbour coefficients of the upwind
differencing method that covers both flow directions is:
ae
aw
Dw + max(Fw,0)
26
De + max(0, Fe)
13
Example 5.2 Solve the problem considered in example 5.1 using the
upwind differencing scheme for
(i) u = 0.1 m/s,
((ii)) u = 2.5 m/s
with the coarse five-point grid.
=1
Dw =
w Aw
xWP
=0
x/2
Fe = ( uA)e
De =
B
7
xWP= x xPE=x
aP = aW + aE + ( Fe Fw ) S P
Fw = ( uA) w
e
P
where
x/2
d
d d
( u ) =
dx
dx dx
The governing equation is:

A
1
27
For interior nodes: xWP = xPE = x

For node 2: xWP = x / 2
For node 6: xPE = x / 2
e Ae
xPE
Node
aW
aE
SP
Su
2
0
De + max(0, Fe ) ( Dw + max( Fw , 0)) ( Dw + max( Fw , 0)) A
3, 4,5 Dw + max( Fw , 0) De + max(0, Fe )
0
0
6
0
( De + max(0, Fe )) ( De + max(0, Fe ))B
Dw + max( Fw , 0)
28
14
u = 0.l m/s:
29
u = 2.5 m/s
Upwind scheme produced a much more realistic solution compared with

central difference scheme.
However, the solution is not very close to the exact value.
30
15
5.6.1 Assessment of the upwind differencing scheme
Conservativeness
the upwind differencing scheme utilises consistent
expressions to calculate fluxes through cell faces: therefore
it can be easily shown that the formulation is conservative
Boundedness
the coefficients of the discretised equation are always
positive and satisfy the requirements for boundedness
Fe Fw = 0 aP = aW + aE
Stable iterative solution
All coefficients are positive

Coefficient matrix is diagonally dominant
Transportiveness
No wiggles in
solution
The scheme accounts for the direction of the flow so

transportiveness is build into the formulation.
31
Accuracy
the scheme is based on the backward differencing formula so the accuracy is only
first order on the basis of the Taylor series truncation error (see Appendix A):
A major drawback of the scheme:
it p
produces erronous results when the flow is not aligned
with the ggrid lines.
g
is smeared error has a diffusion-like appearance false diffusion
32
16
Consider pure convection without diffusion and no source term.

the true solution is:
all nodes above diagonal should be 100
all nodes below diagonal should be 0
Upwind method is not suitable for accurate flow calcualtions

33
5.7 The hybrid differencing scheme

Central differencing scheme: accurate to second order Not transportive
Upwind differencing scheme: accurate to first order is transportive
Hybrid difference scheme uses:
central difference scheme for Pe < 2
upwind difference scheme in which diffusion has been set to zero for Pe 2
For a west face
Pew =
( u )w
Fw
=
Dw w / xWP
(5.35)
The hybrid differencing formula for the net flux through the west face is as
follows:
1
2
1
2
qw = Fw 1 +
W + 1
P
2 Pew
2 Pew
qw = FwW
qw = FwP
34
for
2 < Pew < 2
for
Pew 2
for
Pew 2
(5.36)
17
The general form of the discretised equation is

aPP = aW W + aEE
(5.37)
The central coefficient is given by
After some re-arrangement it is easy to establish that the neighbour
coefficients for the hybrid differencing scheme for steady one dimensional convection diffusion can be written as follows:
aW
aE
F
F
max Fw , Dw + w , 0 max Fe , De e
2
2
35

, 0

Example 5.2 Solve the problem considered in case 2 of

example 5.1 using the hybrid scheme for u=2.5 m/s.
Compare a 5 node solution with a 25 node solution
36
18
Comparison with the analytical solution

The numerical results are compared with the analytical solution in table 5.9
37
5.7.1 Assessment of the hybrid differencing scheme
Is fully conservative
Is unconditionally bounded (since the coefficients
are always positive)
Satisfies the transportiveness property
Produces physical realistic solutions
Highly stable compared with higher order scheme
Is only first order accurate
38
19
Hybrid differencing scheme for multi-dimensional

convection-diffusion
The discretised equation that covers all cases is given by
aPP = aW W + aEE + aSS + aN N + aBB + aT T
with central coefficient

aP = aW + aE + aS + aN + aB + aT + F
39
The coefficient of this equation for the hybrid differencing scheme

are as follows:
One-dimensional flow
two-dimensional flow
three-dimensional flow
aW
max[Fw,(D
(Dw+Fw/2),0]
/2) 0] max[Fw,(D
(Dw+Fw/2),0]
/2) 0] max[Fw,(D
(Dw+Fw/2),0]
/2) 0]
aE
max[-Fe,(De-Fe/2),0]
aS
max[Fs,(Ds+Fs/2),0]
max[Fs,(Ds+Fs/2),0]
aN
max[-Fn,(Dn-Fn/2),0]
max[-Fn,(Dn-Fn/2),0]
aB
max[Fb,(Db+Fb/2),0]
aT
max[-Ft,(Dt-Ft/2),0]
Fe-Fw
Fe-Fw+Fn-Fs
Fe-Fw+Fn-Fs+Ft-Fb
40
20
In the above expressions the value of F and D are calculated

with the following formulae
Face
F
(u)wAw
(u)eAe
(u)sAs
(u)nAn
(u)bAb
(u)tAt
wAw/xWP
eAe/xPE
sAs/ySP
nAn/yPN
bAb/zPN
tAt/zPT
41
The Power Law Scheme

Is a more accurate approximation to the 1-D exact
solution
Produces better results than the hybrid
scheme
y
for Pe > 10 diffusion is set to zero
for 0 < Pe < 10 the flux is evaluated by a
polynomial expression
42
21
For example, the net flux per unit area at the west control volume
face is evaluated using
qw = Fw W w (P W ) for
5
where w = (1 0.1
0 1Pew ) Pew
and
qw = FwW
for
0 < Pe < 10
(5.44a)
Pew > 10
(5.44b)
The coefficients of the one-dimensional descretised equation

utilising the power-law scheme for steady one-dimensional
convection-diffusion are given by
Central coefficient: aP = aW + aE + ( Fe Fw )
and
aW
Dw max 0, (1 0.1 Pew
aE
) + max [ F , 0]
5
De max 0, (1 0.1 Pee
43
) + max [ F , 0]
5
5.9 Higher order differencing schemes for convectiondiffusion problems
Hybrid and Upwind schemes are

Stable
Obey the transportiveness requirement
But have first order accuracy
Are prone to numerical diffusion errors
Such errors can be minimized by employing higher order

discretisations.
CentralDifference scheme is second order accurate but is not
stable.
Formulations that do not take into account the flow direction are
unstable
For more accuracy:
use higher order schemes, which preserve upwinding for
stability
44
22
5.9.1 Quadratic upwind differencing scheme: the QUICK scheme
The quadratic upstream interpolation for convective kinetic (QUICK)

scheme of Leonard(1979) uses a three-point upstream-weighted
upstream quadratic interpolation for cell face values. The face value of
is obtained from a quadratic function through two bracketing nodes
( each
h side
id off the
h face)
f ) andd a node
d on the
h upstream side
id (Fig.
( i 5.17)
1 )
(on
Two upstream nodes and one downstream node is used to calculate the
face value of
45
It can be shown that for a uniform grid the value of at the cell face
between two bracketing nodes i and i-1, and upstream node i-2 is given by
the following formula:
6
3
1
face = i 1 + i i 2
(5.45)
8
8
8
h uw > 0, the
h bbracketing
k i nodes
d for
f the
h west face
f
d P, the
h
When
w are W and
upstream node is WW (Figure 5.17), and
6
3
1
(5.46)
w = W + P WW
8
8
8
When ue > 0, the bracketing nodes for the east face e are P and E, the
upstream node is W ,so
6
8
3
8
1
8
e = P + E W
(5.47)
The diffusion terms may be evaluated using the gradient of the appropriate
parabola.
It is interesting to note that on a uniform grid this practice gives the same
expressions as central differencing for diffusion.
46
23
If Fw>0 and Fe>0 and if we use equations (5.46-5.47) for the convective
terms and central differencing for the diffusion terms, the discretised form of
the one-dimensional convection-diffusion transport equation(5.9) may be
written as Fee Fww = De (E P ) Dw (P W )
(5.9)
6
3
1
3
1
6
Fe 8 P + 8 E 8 W Fw 8 W + 8 P 8 WW = De (E P ) Dw (P W )

which can be rearranged to give
3
6
6
1
3
1
Dw 8 Fw + De + 8 Fe P = Dw + 8 Fw + 8 Fe W + De 8 Fe E 8 FwWW
This is now written in the standard form for discretised equations

aPP = aW W + aEE + aWW WW
where
47
(5.48)
(5.49)
(5 49)
For Fw < 0 and Fe < 0 the flux across the west and east boundaries is given
by the expressions
6
3
1
8
8
8
6
3
1
e = E + P EE
8
8
8
w = P + W E
(5 50)
(5.50)
Substitution of these two formulae for the convective terms in the discretised
convection-diffusion equation (5.9) together with central differencing for the
diffusion terms leads, after re-arrangement as above, to the following
coefficients:
48
24
General expressions, valid for positive and negative flow directions, can be obtained
by combining the two sets of coefficients above.
The QUICK scheme for one-dimensional convection-diffusion problems can be
summarised as follows:
aPP = aW W + aEE + aWW WW + aEEEE
(5.51)
With central coefficient
aP = aW + aE + aWW + aEE + ( Fe Fw )
And neighbour coefficients
where
w=1 for Fw > 0 and e=1 for Fe > 0

w=0 for Fw < 0 and e=0 for Fe < 0
49
Example 5.4 Using the QUICK scheme solve the problem considered in
example 5.1 for u=0.2 m/s on a five-point grid. Compare the quick solution
with the exact and central differencing solution.
A
1
=1
w
W
x/2
e
P
xWP= x xPE=x
B
7
=0
x/2
Boundaryy Points :
Consider node 2. w = A
To calculate e : w is needed. But there is no w use linear

interpolation to create a mirror node at x/2 to the west of boundary A.
50
25
Mirror Node
Domain boundary
Node 2
It can be easily shown that the linearly extrapolated value at the minor
node is given by
(5.52)
0 = 2 A P
The extrapolation to the mirror node has given us the required W node
for the formula (5.47) that calculates e at the east face of control
volume 2:
6
8
3
8
e = P + E
1
7
3
2
( 2 A P ) = P + E A
8
8
8
8
51
(5.53)
At the boundary nodes the gradients in diffusive flux terms

can be evaluated using central difference scheme similar to
calculation of diffusion terms in interior nodes.
52
26
The discretised equations for nodes 2, 3 and 6 are now written to fit into the
standard form to give:
aPP = aWW WW + aW W + aEE + Su
with
(5.59)
aP = aW + aE + aWW + aEE + ( Fe Fw ) S P
The solution is
2 0.9648
0.8707
3
4 = 0.7309

5 0.5226
6 0.2123
(5.60)
(5 60)
53
54
27
5.9.2 Assessment of the QUICK scheme

The scheme:
Uses consistent quadratic profiles is conservative
Is based on a quadratic function has 3rd order truncation error
Is based on 2 upstream and 1 downstream nodes has
transportiveness
aP = anb if flow field satisfies continuity desirable for
boundedness
aE and aW may not be positive aWW and aEE are negative
If uw > 0 and ue > 0 :
F 8
Then aE = De 3 / 8 Fe becomes negative for Pee = e >
De 3
Gives rise to stability problems and unbounded solutions.
QUICK scheme is conditionally stable
Involves WW and EE which are not immediate-neighbour nodes
55
5.9.3 Stability problems of the QUICK scheme and remedies

May have negative main coefficients can be unstable
Also other higher order schemes may be oscillatory and unstable
under certain conditions
In this case use:
Method of deferred correction
In this method the cell face value f is formulated as the sum of the
upwind value and other higher order terms which are evaluated at the
previous iteration.
u
o
f = f + f
HO
of = of of
where:
uf = f value to be computed by 1st order upwind method
HO
0f = f value computed by high order scheme from previous old values

u
0f = f value computed by 1st order upwind method from previous old values
56
28
Let us apply the deferred correction method to QUICK scheme.

For uw > 0 QUICK scheme is
6
3
8
8
This can be written as
1
8
w = W + P WW
w = W +
Similarly:
uf
1
[3P 2W WW ]
8
For Fw > 0
0f is added to source term Su
1
[3E 2P W ]
8
1
w = P + [3W 2P E ]
8
1
e = E + [3P 2E EE ]
8
e = P +
57
F Fe > 0
For
For Fw < 0
For Fe < 0
The discretisation equation takes the form

The central coefficient is
where
aw
ae
Dw + max( Fw , 0) De + max(0, Fe )
(5.62)
(5.63)
((5.64))
Su
max[ Fw , 0](w W ) max[ Fw , 0](w P )
+ max[ Fe , 0](e E ) max[ Fe , 0](e P )
((5.65))
Note that aw and ae are the same as that of the upwind method.
The advantage of this approach is that the coefficients are always

positive and now satisfy the requirements for conservativeness,
boundedness and transportiveness
58
29
5.9.4 general comments on the QUICK differencing scheme
QUICK scheme
Has greater accuracy than central, upwind or power schemes
Retains the upwind weighted characteristics
Resultant false diffusion is small
Can give (minor) undershoots and overshoots (see Fig. 5.20)

59
To prevent this problem use:

1. Limiters
Limit the scheme to have the face value f to be between
certain values (ULTRA SHARP)
2. Total variation diminishing schemes (TVD)
60
30
Homework
H
y
Consider a fluid at a uniform temperature Ti entering a channel whose surface is maintained at a

different temperature Ts. A Thermal boundary layer along the tube developes, after which the form of
the temperature profile does not change. Assume that the flow profile is constant in the channel where
the velocities are given by
2
u
2y
= 1
1 and v = 0
umax
H
where umax = 1.5umean. The energy equation is

( uT ) ( vT ) k T k T
+
=
+
x
y
x c p x y c p y
Find the temperature profile in the channel for Re = umeanH/ = 10, Pr = cp/k = 1. Use Lx/H = 5, where
Lx is the length of the solution domain. Use UPWIND method. (Note: k/cp = /Pr for fluids.). Also,
choosing = 1, find from Re relation. Take Tin = 0, Twalls = 100, umean = 1 m/s
61
Generalisation of Upwind-biased Schemes

For convection terms, an estimate of value at the faces of a CV is
required. Consider east face, assuming ue > 0
1) Standard Upwind Differencing Scheme (UD)
P
w
WW
e = P
e
EE
ve
UPWIND
The face value of is taken to be equal to the value of the upstream

node;
e = P
(5.66)
62
31

2) Linear Upwind Differencing Scheme (LUD) also called the second
order upwind differencing scheme (SOU)
e = P +(P W) / 2
P
w
WW
SOU (LUD)
EE
ve
is assumed to vary linearly between W and e. Then e is found by

extrapolating the two upstream node values W and P to face e.
(P W ) x
x
2
1
= P + (P W )
2
e = P +
(5.67)
The term (P W) can be thought as a second order correction to

the standard upwind scheme.
63

3) Central Differencing Scheme (CD)
e = (P + W) / 2
e
w
WW
CENTRAL
EE
ue
The value of is assumed to vary linearly between the two nodes

straddling the face, that is;
( + )
(5 68)
(5.68)
e = P E
2
or
1
2
(5.69)
64
e = P + (E P )
32

4) QUICK Scheme
e = 6/8P + 3/8E 1/8W)
P
W
w
WW
e
P
QUICK
EE
ue
The scheme is based on the assumption that varies in terms of a

second degree polynomial between two upstream (W and P) and the
downstream node E.
E
6
3
1
(5.70)
e = P + E W
8
8
8
1
(5.71)
e = P + (3E 2P W )
or
8
65

All higher order schemes can be expressed in the form:
1
e = P + (E P )
2
= an appropriate
pp p
function
(5.72)
Convective flux at face e is Fee

For a higher order scheme convective flux consist of two parts:
1) Upwind flux, FeP
2) Additional flux, Fe(E P)/2
Additional flux is connected to the gradient of at face e, as
indicated by (E P)
66
33

= 0 for UD scheme
= 1 for CD scheme
LUD scheme may be written as
1
e = P + P W (E P )
2 E P
(5.73)

= P W for LUD scheme
E P
(5.74)
QUICK scheme may

Q
y be written as
1
2
P W
E P
e = P + 3 +

=3+ P W
E P
1
(E P )
4
(5.75)
1
for QUICK scheme
4
67
(5.76)

let
r=
P W
E P
(5.77)
r = ratio of upwind-side gradient to downwind-side gradient

is a function of r:
= (
(r))
A higher order convection scheme can be written as
1
e = P + (r )(E P )
2
= 0 for UD scheme
(5.78)
= 1 for CD scheme
P W
for LUD scheme
E P
1
= 3 + P W for QUICK scheme
E P 4
68
34
All of the above expressions assume that the flow

direction is positive (from west to east).
Similar expressions
exist for negative
flow direction.
p
g
In that case, r is still the ratio of upwind-side
gradient to downwind-side gradient.
69
Total Variation and TVD Schemes

UD scheme is the most stable scheme (no wiggles)
CD and QUICK have higher order accuracy but give rise
to wiggles under certain conditions.
Our aim is to find a convection scheme with a higherorder accuracy but without wiggles.
The desirable property for a stable, non-oscillatory, higher
order scheme is monotonicity preserving.
For a scheme to preserve to preserve monotonicity:
1. It must not create local extrema
2. The value of an existing local minimum must be non-decreasing
and that of a local maximum must be non-increasing.
Monotonicity preserving schemes do not create

new undershoots and overshoots.
70
35

Consider the discrete data set shown in the figure.
The total variation of this data set is

TV ( ) = 2 1 + 3 2 + 4 3 + 5 4
(5.79)
= 3 1 + 5 3
For monotonicity, this TV must not increase with

time.
71

In other words TV must diminish with time.
Hence, the term total variation diminishing or
TVD.
Originally TVD was developed for time-dependent
flows.
For TVD: TV(n+1) TV(n) where n refer to time
step.
In the next section we show how TVD is also linked
to desirable behaviour of discretisation schemes for
steady convection-diffusion problems.
72
36
Criteria for TVD Schemes

Necessary and sufficient conditions for a scheme to be TVD
1) For 0 < r < 1 (r) 2r
2) For r 1 (r) 2
UD scheme is TVD
LUD scheme is not TVD for r > 2
CD scheme is not TVD for r < 0.5
QUICK scheme is not TVD for r < 3/7 and r > 5
73
Requirement for Second Order Accuracy

For second order accuracy, the flux limiter function should pass
through the point (1, 1) in the r diagram.
Range of possible second-order schemes is bounded by the CD and
LUD schemes:
For 0 < r < 1 for TVD to be second order r (r) 1
For r 1 for TVD to be second order 1 (r) r
Region for a second-order TVD scheme

74
37
Symmetry Property for Limiter Functions

Symmetry Property for limiter functions:
(r )
(5.80)
= (1/ r )
r
A limiter function that satisfies the symmetry
property ensures that backward and forward-facing
gradients are treated in the same fashion without the
need for special coding.
75
Flux Limiter Functions

Name
Van Leer
V Alb
Van
Albada
d
Min-Mod
Limiter function
Source
r+ r
Van Leer (1974)
1+ r
r + r2
1+ r2
V
Van Alb
Albada
d et all. (1982)
min(r ,1) if r > 0
if r 0
0
(r ) =
Roe (1985)
SUPERBEE
max[0, min(2r ,1), min( r , 2)]
Roe (1985)
Sweby
max[0, min( r ,1), min(r , )]
Sweby (1984)
QUICK
UMIST
S
max[0, min(2r , (3 + r ) / 4, 2)]

max[0,
[0 min(2
i (2r , (1 + 3r ) / 4,
4 (3 + r ) / 4,
4 2)]
Leonard (1988)
Lien
i andd Leschziner
h i
(1993)
0 2
= 1 Min-Mod Limiter
= 2 SUPERBEE Limiter of Roe
76
38
Flux Limiter Functions
MINMOD
MINMOD
All Limiter functions in a r diagram

All limiter functions are symmetric except QUICK limiter.
UMIST limiter function is a symmetric version of the QUICK limiter.
77
Implementation of TVD Schemes

For the one dimensional convection diffusion equation
d
d d
( u ) =
(5.81)
dx
dx dx
The coefficients of the discretized equation are written in the deferred correction
approach.
h IIn thi
this approach,
h the
th aE, aW, aP coefficients
ffi i t are the
th same as off UD scheme.
h
The extra terms resulting from the application of a limiter function is added to the
source term Sdc.
The face values are:
For u > 0
For u < 0
1
2
1
w = W + (rw+ )(P W )
2
e = P + (re+ )(E P )
1
2
1
w = P + (rw )(W P )
2
e = E + ( re )(P E )
78

re+ = P W
E P

rw+ = W WW
P W

re = EE E
E P

rw = E P
P W
(5.82)
(5.83)
39
Implementation of TVD Schemes

The discretisation equation takes the form
aPP = aW W + aEE + S dc
(5.84)
The central coefficient is

(5 85)
(5.85)
where
aw
ae
Dw + max( Fw , 0) De + max(0, Fe )
S dc
max[ Fw , 0](w W ) max[ Fw , 0](w P )
+ max[ Fe , 0](e E ) max[ Fe , 0](e P )
e and w are as defined in Eqs. (5.82) and (5.83)
((5.86))
Note that Sdc is the same as defined in Eq. (5.65).

Note also that aw and ae are the same as that of the upwind method.
The advantage of this approach is that the coefficients are always positive
and now satisfy the requirements for conservativeness, boundedness and
transportiveness
79
Evaluation of TVD Schemes
Comparison of TVD schemes for pure convection flowing 45o to the grid direction.
TVD schemes does not give unphysical overshoots or undershoots.

However, TVD schemes require about 15% more CPU time.
80
40

Chapter 5 PDF

Uploaded by

Copyright:

Available Formats

Chapter 5 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 5 PDF

Uploaded by

Copyright:

Available Formats

Chapter 5

The Finite Volume Method for

Prepared by: Prof. Dr. I. Sezai

Integration over the control volume gives :

n ( u)dA = n (grad )dA + S dV

This equation represents the flux balance in a control volume.

I. Sezai - Eastern Mediterranean University

Steady one-dimensional convection and diffusion

The flow must also satisfy continuity, so

Integrating Eqn. (5.3) over the CV

Integrating continuity Eqn.

I. Sezai - Eastern Mediterranean University

Let F = uA convective mass flux

We assume that velocity field is known Fe, Fw known.

I. Sezai - Eastern Mediterranean University

The Central Differencing Scheme

I. Sezai - Eastern Mediterranean University

which is of the form

I. Sezai - Eastern Mediterranean University

(iii) Case 3: u = 2.5 m/s (20 CVs)

ME555 : Computational Fluid Dynamics

The governing equation is:

I. Sezai - Eastern Mediterranean University

For interior nodes: xWP = xPE = x

I. Sezai - Eastern Mediterranean University

The resulting system of equations are

Solve the system of equations using Tri-diagonal matrix algorithm

I. Sezai - Eastern Mediterranean University

The solution for case 1 is:

Exact solution is:

ME555 : Computational Fluid Dynamics

Comparison of the numerical result with the

I. Sezai - Eastern Mediterranean University

The solution for case 2: (u = 2.5 m/s, 5 CVs)

Comparison of the numerical result with the analytical solution.

The solution appears to oscillate about the exact solution.

I. Sezai - Eastern Mediterranean University

The solution for case 3: (u = 2.5 m/s, 20 CVs)

Comparison of the numerical result with the analytical solution.

Grid refinement has reduced the F/D ratio from 5 to 1.25.

I. Sezai - Eastern Mediterranean University

Properties of Discretisation Schemes

ME555 : Computational Fluid Dynamics

I. Sezai - Eastern Mediterranean University

ME555 : Computational Fluid Dynamics

I. Sezai - Eastern Mediterranean University

Example of consistent specification of diffusive fluxes

e1 = w2, e2 = w3 and e3 = w4 Fluxes across CV faces are

I. Sezai - Eastern Mediterranean University

Flux Consistency ensures conservation of over the entire domain

For nodes 1, 2 and 3 quadratic function 1 is used.

I. Sezai - Eastern Mediterranean University

< 1 at one node at least

If eqn. (5.22) is satisfied, resulting matrix coefficients are diagonally

I. Sezai - Eastern Mediterranean University

Another essential requirement for boundedness is that all coefficients

ME555 : Computational Fluid Dynamics

I. Sezai - Eastern Mediterranean University

Distribution of in the vicinity