PHYSICS 72 Experiment 1 Standing Wave

Group #:
Members
Date Performed:
Date Submitted:
Experiment # 1
Standing Waves In A String
I. OBJECTIVE
To study the variation in the wave speed of a vibrating string with stretching force,
frequency and length of the string.
II. APPARATUS
Sine Wave Generator
String Vibrator
Braided String (inelastic, low-density)
Banana Patch Cords (qty. 2)
Clamp or other device of securing the String Vibrator
Pulley
Mounting Rod for Pulley
Clamp
Mass and Hanger Set
Tape Measure
III. INTRODUCTION
The general appearance of waves can be shown by means of standing waves in a
string. This type
of wave is very important because most vibrations of extended bodies, such as the
prongs of a
tuning fork or the strings of a piano, are standing waves. In this experiment you will
discover how
the speed of the wave in a vibrating string is affected by the length of the string, the
stretching
force and the frequency of the wave.
Theory
Standing waves (stationary waves) are produced by the interference of two traveling
waves, both
of which have the same wavelength, speed and amplitude, but travel in opposite
directions
through the same medium. The necessary conditions for the production of standing
waves can be
met in the case of a stretched string by having waves set up by some vibrating body,
reflected at
the end of the string and then interfering with the oncoming waves.
A stretched string has many natural modes of vibration. If the string is fixed at both ends
then there must be a node at each end. It may vibrate as a single segment, in which
case the length (L) of the string is equal to 1/2 the wavelength () of the wave. It may
also vibrate in two segments with a node at each end and one node in the middle; then
the wavelength is equal to the length of the string. It may also vibrate with a larger
integer number of segments. In every case, the length of the string equals some integer
number of half wavelengths. If you drive a stretched string at an arbitrary frequency, you
will probably not see any particular mode; many modes will be mixed together. But, if the
driving frequency, the tension and the length are adjusted correctly, one vibrational
mode will occur at much greater amplitude than the other modes.
For any wave with wavelength and frequency f, the speed, v, is

(eq. 1)
v=f
In this experiment, standing waves are set up in a stretched string by the vibrations of an
electrically-driven string vibrator. The arrangement of the apparatus is shown below. The
tension in the string equals the weight of the mass suspended over the pulley. You can
alter the tension by changing the mass. You can adjust the amplitude and frequency of
the wave by adjusting the output of the Sine Wave Generator, which powers the string
vibrator.
IV. PROCEDURE
1. As shown in the picture, clamp the Sine Wave Generator and pulley about 120 cm
apart.
Attach about 1.5 m of braided string to the vibrating blade, run it over the pulley, and
hang
about 150 g of mass from it.
2. Measure from the knot where the string attaches to the string vibrator to the top of
the pulley.
This is distance L. (Note that L is not the total length of the string, only the part that is
vibrating.)
3. Turn on the Sine Wave Generator and turn the Amplitude knob all the way down.
Connect the Sine Wave Generator to the string vibrator using two banana patch
cords. Polarity does not matter.
Wavelength and Frequency
1. Set the Amplitude knob about midway. Use the Coarse (1.0) and Fine (0.1) Frequency
knobs of the Sine Wave Generator to adjust the vibrations so that the string vibrates in
one segment. Adjust the driving amplitude and frequency to obtain a large-amplitude
wave, but also check the end of the vibrating blade; the point where the string attaches
should be a node. It is more important to have a good node at the blade than it is to
have the largest amplitude possible. However, it is desirable to have a large amplitude
while keeping a good node.
2. Record the frequency. How much uncertainty is there in this value? How much can you
change the frequency before you see an effect?
3. Repeat steps 1 and 2 for a standing wave with two segments. The string should
vibrate with a
node at each end and one node in the center.
4. How is the frequency of the two-segment wave related to the frequency of the onesegment wave? Calculate the ratio of the frequencies. Is the ratio what you would
expect?
5. Try touching the string at an anti-node. What happens? Try touching the string at the
central node. Can you hold the string at the node and not significantly affect the
vibration?
6. What was the wavelength when the string was vibrating in one segment? Use
Equation 1 to calculate the speed of the one-segment wave.
7. Calculate the speed of the two-segment wave. How do these to values compare? Are
they about the same? Why?
8. Adjust the frequency so that the string vibrates in three segments. Has the velocity
changed? Does the speed of the wave depend on the wavelength and the frequency?
Changing Tension
1. Adjust the frequency so that the string vibrates in two segments. Now, without
changing the frequency, decrease the mass on the hanger until the string vibrates in 4
segments. (You may have to use small masses to get a good waveform. Remember that
it is more important to have a good node at the end of the blade than to have the
biggest amplitude possible.)
2. Record the total hanging mass, including the mass hanger. Calculate the ratio of the
new mass to the original mass. Why is the ratio not 2?
Changing Length
1. Return the mass to its original amount. Set the frequency to a value between the
frequencies that produced waves of two and three segments. Adjust the frequency so
that no particular standing waveform is present.
2. Unclamp the string vibrator and slowly move it towards the pulley. (Do not let go of
the string vibrator without clamping it to the iron stand again.)
3. Without changing the driving frequency or the hanging mass decrease the length of
vibrating string until it vibrates in two segments. Adjust the position to get the best node
at the blade, as before. (If the hanging mass touches the floor, reattach it to the string
higher up.)
4. Measure the new wavelength and calculate the speed of the wave. Is it about the
same as
before? Does the speed of the wave depend on the length of the string?
IV. DATA AND COMPUTATIONS
QUESTIONS:
1) If the string had several knots tied at irregular intervals along its length, could
standing waves be set
up in it?
2) A wave is represented by the equation y = 0.20 sin 0.40(x 60t), where all
distances are measured
in centimeters and time in seconds. Find: a) the amplitude, b) the wavelength,
c) the speed, and d)
the frequency of the wave. e) What is the displacement at x = 5.5 cm and t =
0.020 sec?
V. OBSERVATION AND DISCUSSION
VI. CONCLUSION:

PHYSICS 72 Experiment 1 Standing Wave

Uploaded by

Copyright:

Available Formats

PHYSICS 72 Experiment 1 Standing Wave

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PHYSICS 72 Experiment 1 Standing Wave

Uploaded by

Copyright:

Available Formats

What is the objective of this experiment?

How does changing the tension in the string affect the standing waves?

Group #:

For any wave with wavelength and frequency f, the speed, v, is

You might also like