Coaxial Cables

Many consumers, when they think of "coaxial cable," tend to think it refers only to the cabling used by
cable and satellite companies for cable TV. However, this is only one example of coaxial cable. In this
article we will breakdown what makes up a typical coaxial cable as well as go over a few common
types.

Coax cable is defined as any cable with the following properties:

A center conductor
Insulation covering the center conductor, called a "dieletric"
A braided shield surrounding the dieletric
An optional foil shield
An outer jacket

Each of these components plays a specific role. Let's take a look at each in more detail:
Center Conductor:
At the heart of a coaxial cable is a center conductor. Typically constructed of either pure copper (in
higher-end cables) or copper-coated steel or aluminum (in less-expensive cables), the center
conductor is responsible for transmitting the cable's signal. As such, it must meet certain electrical
properties (such as wire resistance). The rest of the cable construction is primarily designed to help
the center conductor maintain its electrical integrity.
Dielectric Insulator:
The dielectric insulator's purpose is two-fold; first, it acts as an insulator between the center conductor
and the outer braided / foil shielding. Second, it helps physically hold the center conductor in the
center of the cable. This is important, as signal loss can occur if the center conductor strays too close

to the outer area of the cable. Various materials are commonly used for the dielectric. A few of the
more common materials, in order of quality (from best to worst), are below:
1.

Foamed Polyethylene (FPE)

2.

Teflon

3.

Polyethylene (PE)

4.

Polypropylene (PP)

5.

Polyvinylchloride (PVC)

When reading specifications on coaxial cables, you may see references to the dialetric constant. The
closer this number is to 1.0, the better. Foamed Polyethylene (FPE), for example, generally has a
dielectric constant somewhere around 1.5, while PVC's dialetric constant is around 3.0 to 4.0.
(Foamed PE basically uses gas, often nitrogen, to create gas bubbles in the material to lower the
dielectric constant. Marketing literature that refers to "gas-injected dielectric" usually indicates the use
of FPE. It is one of the best dielectric materials in common use.)
Braided Shield:
Long copper cables have a tendency to act like antennas, picking up stray signals from the
environment. These unwanted signals, known as "interference", disrupt the signal that the cable is
supposed to be carrying. Interference tends to come in two different flavors: electromagnetic
interference (known as EMI) and radio frequency interference (RFI). EMI interference is often caused
by heavy power lines, cell phone signals, etc. A braided shield protects the signal from EMI
interference.
When looking at cable specs, the braided shield will often be expressed in a percent coverage, which
often ranges anywhere from 30% to 95% coverage. The higher the coverage, the better the
protection.
Foil Shield:
Although not always present on coaxial cables, the foil shield serves to protect from RFI interference.
Foil shields are almost always made out of aluminum foil, and simply wrap around the inner parts of
the cable. Unlike braided shields, which have a percent coverage, foil shields always cover 100%.
Outer Jacket:
The outer jacket is generally made out of flexible PVC (polyvinyl chloride) and serves primarily to hold
the cable together and protect it from the elements.

Connectors
There are many different connectors that can terminate a coaxial cable. We will now go over a few of
the more common connectors.
RCA
The RCA connector was

developed in the early '40s by the Radio Corporation of America to connect record players to
amplifiers. The same basic connector is still in wide use today, and it represents a large portion of the
connectors used for home theater cables. The fact that they are so easy to connect and disconnect
makes RCA connectors a popular choice for home theater applications. RCA cables can be used for
audio, video and digital audio.
The biggest drawback with RCA devices is that each signal is sent on a different cable. For example, a
single RCA-terminated coax cable only carries the left audio channel, or only the right, etc. Three RCA
cables are needed for high-def video, along with two more for the audio. This makes for a mess of
cables behind your equipment. This is one reason that has made HDMI cables so popular.
Attaching RCA connectors can be a bit more time-consuming as, with some types of RCA connectors,
the coaxial cable's wires need to be soldered to the connector after stripping the cable with a stripping
tool. RCA connectors come in solder-on, weatherproof and compression styles. A special tool is
required for compression connectors, and a soldering iron is
needed for solder-on connectors.
BNC
The BNC connector has two bumps on the female side that slide
into corresponding grooves on the male side. The connector is
then rotated a quarter turn to lock into place. BNC connectors
are widely used in commercial applications such as closed circuit
television systems, where its ability to lock in place (unlike the
slip-on RCA) makes BNC cables a perfect fit. BNC connectors come in a wide variety as well, including
twist-on and weatherproof connectors.
F-Pin
The F-Pin connector is probably the most recognized of the coaxial connectors as it's been in use with
televisions and VCRs for decades. The familiar threaded connector makes for a secure connection that
will not easily slip out of a device. This connector is also one of the easiest to attach to a coax cable as
it does not require any soldering. Many different types are available including twist-on, crimp-on and
compression. For outdoor use, weatherproof connectors are also available to create an F-Pin cable
with a secure connection and loss-less signal transfer.
Many manufacturers are doing away with the F-pin
connector on their TVs. This is because that little F-pin
connector is actually part of a device called a tuner. The
tuner is what sifts through the signal coming through the
cable and separates all of the TV channels. Since so
many people change channels using a cable box or
satellite receiver, these tuners are becoming obsolete.
This can pose a problem for folks who have standard
cable TV that still requires the TV to have an F-pin connector. Unfortunately, a small adapter or special
cable won't do the trick. A tuner is required. There are a couple ways to do this. One way is to use an

old VCR. VCRs have built in tuners. The other way is to use a device called an RF demodulator. A
demodulator is essentially a TV tuner that will let you change the channels.
Crimp-on, solder or twist-on?
There are 3 main styles of each connector available on the market. With each of these styles the
coaxial cable must be stripped in such a way that a portion of each component of the cable is
exposed:

Crimp: This encompasses compression as well as crimping connectors. Crimping connectors slide onto
the cable and then pinche the base of the connector onto the outer jacket. The compression connectors
require a special tool to press the cable into the connector and pinch it all at the same time. Weatherproof

connectors are most often compression style, where the connector seals to keep water out.
Solder: This style, like its name implies, requires the center conductor and the braided shield to be

soldered to parts of the connector. These offer the best connection, but are more labor-intensive to install.
Twist-on: These are for the consumer that just wants a quick and easy solution. Especially handy if you
are only trying to fix a single broken cable, these don't require any solder or tools. Simply twist the
connector onto the cable and you're done. They're not the best for durability, but they get the job done.

Types of Coaxial Cable

RG58
Largely used in the commercial security camera industry, RG58 cable is a low profile, inexpensive
choice for large projects where a high-bandwidth cable is not needed. Most often terminated with BNC
connectors, this type of cable can also be found attached to testing equipment and 2-way radio
systems.
RG59
Once the standard for cable TV, RG59 cables are still found packaged with VCRs and televisions. RG59
was a good low-cost option for cable TV for years until the cable industry recently began its move into
digital cable television, which needs a thicker cable. Modern satellite television also requires a higherbandwidth-capable cable and so RG6 coaxial cable is becoming much more popular, making RG59 no
longer the industry standard.
RG6
RG6 cable is differentiated from RG59 cable by having a thicker copper center conductor. RG6 is
primarily being used today for satellite and digital cable TV, where higher frequencies are required
that RG59 cable cannot support. RG6 cable is most often sold with F-pin connectors for cable or
satellite applications.