Polymeric Insulator Cleaning Procedure

Hi*Lite XL Insulator
Recommended Cleaning
Procedures
POWER SYSTEMS, INC.
Web: http://www.hubbellpowersystems.com
E-mail: [email protected]
Phone 573-682-5521
Copyright
Fax 573-682-8714
2004 Hubbell 210 North Allen Street Centralia, MO 65240
Bulletin EU1272-HR
Introduction
They are:
Hi*Lite XL transmission line insulators normally require no cleaning, washing, or other

routine maintenance. Chalking of the rubber
weathershed surfaces that are exposed to
sunlight in normal as is darkening of the surfaces that are shaded or sheltered from the
sun. Neither condition is indicative of the need
for cleaning.
1. Salt
Washing or cleaning may be required if the

insulators are installed in areas of severe
environmental contamination and, there are
indications of abnormal leakage currents or
scintillations on the insulator surface in fog,
mist or other conditions of light wetting.
In the event that washing or cleaning is required, the procedures outlined in Section IX
of the "IEEE GUIDE FOR INSULATOR
CLEANING", P957 are generally applicable.
Type of Contaminants
Insulators in service are subject to surface dirt,
to some degree, in all operating areas. Most
commonly encountered contaminants have
little effect on insulator performance as long as
the surface is dry. Fog, mist, or light rain can
create a condition which results in a conductive surface film on the dirty insulator surface
without washing the contaminant from the
surface.
Contaminants are generally classified by the
source of the airborne impurities. Local agricultural, industrial, and geographic conditions
determine which contaminants are present in
the atmosphere.
Seven types of contaminants which can affect
insulator performance have been identified.
Page 2
EU1272-HR
Substantial salt deposits may result from windblown spray in areas near bodies of salt water
and in areas adjacent to highways, particularly
elevated roads, where salt is used to remove
snow or ice. These deposits dissolve quickly
and are normally washed off by heavy rain. It
may be necessary to clean insulators in these
areas when long, dry periods are followed by
intervals of light misty rain or fog.
2. Cement/Lime
Insulators located near cement plants, construction sites, or rock quarries may accumulate deposits of cement or lime. These materials can build up thick, hard, crusty layers on
the insulator surface. When these deposits are
lightly wetted, leakage currents flowing on the
insulator surface may be trapped along the
insulator/contaminant interface and the resulting high temperatures may degrade or erode
the weathershed surface
3. Dust
The dusts that can be deposited on insulators
originate from a wide variety of sources.
These dusts include fertilizers and other agricultural dusts and coal dust as well as the soot
and fly ash by-products from the industrial
burning of coal.
4. Defecation
Insulators located in the vicinity of roosts of
large birds of prey are subject to contamination by the defecation of those birds. Eagles,
hawks, and other large birds often roost on or
hunt from transmission line support structures.
5. Chemical
Atmospheric pollutants from a wide variety of
industrial chemical processes and aerial
spraying of agricultural and fire fighting chemicals are deposited on insulators. The characteristics of those chemicals vary widely and
they may or may not be water soluble.
we
6. Smog
can follow this
Automobile emissions and other industrial

emissions in urban areas introduce significant
amounts of particulate matter into the environment. The characteristics of the resulting
insulator contamination will depend upon the
combination of pollutants present in the atmosphere.
7. Cooling Tower Effluent
Cooling tower effluent is composed of water
vapor and small amounts of dissolved solids
which should quickly disperse under normal
wind and temperature conditions. Under some
conditions, however, the effluent can create
localized fog which can moisten dry, dirty
insulators to adversely affect insulator performance. The result would depend upon the
characteristics of the dry contaminant and its
reaction with the chemistry of the effluent fog.
Caution:
Proper safety standards and operating and
maintenance procedures must be strictly
followed to prevent injury to personnel and
damage to equipment. Local work rules should
govern. In their absence, other recognized
industry standards and codes may be employed. These include ANSI C2 (National
Electrical Safety Code) and IEEE P957/D7
(Guide for Cleaning Insulators). Another recommended document is "Application of Insulators in a Contaminated Environment," IEEE
Transactions on Power Apparatus and Systems, Vol. PAS-98, September/October 1979,

pp. 1676-1695.
Hi*Lite XL polymer insulators can be safely
cleaned while energized or deenergized by
adhering to proper cleaning procedures.
Deenergized Cleaning
If the insulators can be deenergized for cleaning, they can be hand washed with rags or
wiping cloths in detergent water followed by a
low pressure flood rinse with clean water to
remove any residue. Solvents or harsh abrasives are normally not required to effectively
clean the insulator weathersheds. Wetting
agents or additives such as Poly-sol can be
used to improve the washing action of the
cleaning water. Solvents such as Stoddard
(Safety) Solvent or Chlorothene may be used
with steel wool, if necessary, provided all
cleaning residue and metal particles are removed by the final clean water rinse.
Energized Cleaning
Two techniques can be used to clean energized Hi*Lite XL polymer insulators. They are
compressed air with dry abrasive and low
pressure water washing. Abrasive cleaning is
often more effective in removing hard, thick, or
caked deposits such as cement or lime.
Compressed Air/Dry Abrasive Cleaning
This procedure involves the use of compressed air and dry, abrasive cleaning media.
Equipment required includes an air compressor capable of supplying air at a minimum of
0.052 cubic meters/second (110CFM) at a
pressure of 860 kPa (125 psi) along with a
pressure blaster, applicator wand, supply
hose, and abrasive cleaning media.
Page 3
EU1272-HR
An air dryer is often used between the compressor and the pressure blaster to remove
moisture from the compressed air.
Commonly used abrasive cleaning compounds
consist of ground corn cob mixed with ground
walnut or pecan shells. Powdered silica or lime
may be either added to the compound or used
alone for increased abrasiveness.
The actual cleaning process is similar to sandblasting in that a pressurized air stream is used
to bombard the insulator surfaces with the
abrasive media. After cleaning, the contaminant and abrasive residue remaining on the
insulator surfaces are blown off with dry, clean,
compressed air.
With the proper cleaning media and procedures, virtually any contaminant can be safely
removed from the insulator surfaces without
the need for area cleanup of the abrasive
residue.
These represent the acceptable

washing angles for Hi*Lite XL post
and suspension insulators.
Water Cleaning
Any water washing procedure must be confined to flood wash pressure. The acceptable
water pump pressure is 1380 kPa (200 psi) at
the ground level pump. To prevent possible
damage to the insulator, the distance from the
spray nozzle or wand to the insulator should
not be less than 4.6 meters (15 feet).
The washing procedure is to start from the
energized end of the insulator and work toward
the grounded end. By removing contaminants
from the energized end first, the weathersheds
just cleaned will maintain an adequate insulation level.
NOTE: Because Hubbell has a policy of continuous product improvement, we reserve the right to change design and specifications without notice.
Page 4
EU1272-HR

Polymeric Insulator Cleaning Procedure

Uploaded by

Copyright:

Available Formats

Polymeric Insulator Cleaning Procedure

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Polymeric Insulator Cleaning Procedure

Uploaded by

Copyright:

Available Formats

Hi*Lite XL Insulator

POWER SYSTEMS, INC.

2004 Hubbell 210 North Allen Street Centralia, MO 65240

Hi*Lite XL transmission line insulators normally require no cleaning, washing, or other

Washing or cleaning may be required if the

can follow this

Automobile emissions and other industrial

Transactions on Power Apparatus and Systems, Vol. PAS-98, September/October 1979,

These represent the acceptable

You might also like