SI Heat 4e Chap07 Lecture PDF

Heat and Mass Transfer: Fundamentals & Applications
Fourth Edition in SI Units

Yunus A. Cengel, Afshin J. Ghajar
McGraw-Hill, 2011
Chapter 7
EXTERNAL FORCED
CONVECTION
Mehmet Kanoglu
University of Gaziantep
Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Objectives
Distinguish between internal and external flow.
Develop an intuitive understanding of friction drag and
pressure drag, and evaluate the average drag and
convection coefficients in external flow.
Evaluate the drag and heat transfer associated with

flow over a flat plate for both laminar and turbulent flow.
Calculate the drag force exerted on cylinders during
cross flow, and the average heat transfer coefficient.
Determine the pressure drop and the average heat
transfer coefficient associated with flow across a tube
bank for both in-line and staggered configurations.
DRAG AND HEAT TRANSFER IN EXTERNAL FLOW
Fluid flow over solid bodies frequently

occurs in practice such as the drag force
acting on the automobiles, power lines,
trees, and underwater pipelines; the lift
developed by airplane wings; upward
draft of rain, snow, hail, and dust particles
in high winds; and the cooling of metal or
plastic sheets, steam and hot water pipes,
and extruded wires.
Free-stream velocity: The velocity of the

fluid relative to an immersed solid body
sufficiently far from the body.
It is usually taken to be equal to the

upstream velocity V (approach
velocity), which is the velocity of the
approaching fluid far ahead of the body.
The fluid velocity ranges from zero at the

surface (the no-slip condition) to the freestream value away from the surface.
Friction and Pressure Drag
Drag: The force a flowing fluid exerts on a

body in the flow direction.
The components of the pressure and wall

shear forces in the normal direction to flow tend
to move the body in that direction, and their
sum is called lift.
Both the skin friction (wall shear) and pressure

contribute to the drag and the lift.
The drag force FD depends on the density of the fluid, the upstream velocity
V, and the size, shape, and orientation of the body, among other things.
The drag characteristics of a body is represented by the dimensionless drag
coefficient CD defined as
The part of drag that is due directly to wall

shear stress w is called the skin friction drag
(or just friction drag) since it is caused by
frictional effects, and the part that is due
directly to pressure P is called the pressure
drag.
At low Reynolds numbers, most drag is

due to friction drag.
The friction drag is proportional to the

surface area.
The pressure drag is proportional to the

frontal area and to the difference
between the pressures acting on the
front and back of the immersed body.
The pressure drag is usually dominant

for blunt bodies and negligible for
streamlined bodies.
When a fluid separates from a body, it

forms a separated region between the
body and the fluid stream.
Separated region: The low-pressure

region behind the body where
recirculating and backflows occur.
The larger the separated region, the
larger the pressure drag.
Wake: The region of flow trailing

the body where the effects of the
body on velocity are felt.
Viscous and rotational effects are
the most significant in the
boundary layer, the separated
region, and the wake.
6
Heat Transfer
Local and average
Nusselt numbers:
Average Nusselt number:

Film temperature:
Average friction
coefficient:
Average heat transfer
coefficient:
Heat transfer rate:
7
PARALLEL FLOW OVER FLAT PLATES

The transition from laminar to turbulent flow depends on the surface geometry,
surface roughness, upstream velocity, surface temperature, and the type of fluid,
among other things, and is best characterized by the Reynolds number.
The Reynolds number at a distance x from the leading edge of a flat plate is
expressed as
A generally accepted value for

the Critical Reynolds number is
The actual value of the engineering

critical Reynolds number for a flat
plate may vary somewhat from 105 to
3 106, depending on the surface
roughness, the turbulence level, and
the variation of pressure along the
surface.
8
Friction Coefficient
Combined laminar + turbulent flow:
10
Heat Transfer Coefficient

The local Nusselt number at a location x for laminar flow over a flat
plate may be obtained by solving the differential energy equation to be
These relations are for

isothermal and smooth surfaces.
The local friction and heat transfer

coefficients are higher in turbulent
flow than they are in laminar flow.
Also, hx reaches its highest values
when the flow becomes fully
turbulent, and then decreases by a
factor of x0.2 in the flow direction.
The variation of the local friction
and heat transfer coefficients for
flow over a flat plate.
11
Nusselt numbers for average heat transfer coefficients
Laminar +
turbulent
For liquid metals

For all liquids, all Prandtl numbers
Graphical representation of the average

heat transfer coefficient for a flat plate with
combined laminar and turbulent flow.
12
13
Flat Plate with Unheated Starting Length

Local Nusselt numbers
Average heat transfer coefficients
Flow over a flat plate

with an unheated
starting length.
14
Uniform Heat Flux

For a flat plate subjected to uniform heat flux, the local Nusselt
number is given by
These relations give values that are 36 percent higher for

laminar flow and 4 percent higher for turbulent flow relative
to the isothermal plate case.
When heat flux is prescribed, the rate of heat transfer to or
from the plate and the surface temperature at a distance x
are determined from
15
FLOW ACROSS CYLINDERS AND SPHERES

Flow across cylinders and spheres is frequently encountered in practice.
The tubes in a shell-and-tube heat exchanger involve both internal flow through
the tubes and external flow over the tubes.
Many sports such as soccer, tennis, and golf involve flow over spherical balls.
At very low velocities, the fluid

completely wraps around the
cylinder. Flow in the wake region is
characterized by periodic vortex
formation and low pressures.
Laminar boundary layer

separation with a turbulent
wake; flow over a circular
cylinder at Re = 2000.
16
For flow across a cylinder or sphere, both the friction drag and the pressure drag
can be significant.
The high pressure in the vicinity of the stagnation point and the low pressure on
the opposite side in the wake produce a net force on the body in the direction of
flow.
The drag force is primarily due to friction drag at low Reynolds numbers (Re < 10)
and to pressure drag at high Reynolds numbers (Re > 5000).
Both effects are significant at intermediate Reynolds numbers.
Average drag
coefficient for
cross-flow
over a smooth
circular cylinder
and a smooth
sphere.
17
18
Effect of Surface Roughness

Surface roughness, in general, increases the drag coefficient in turbulent flow.
This is especially the case for streamlined bodies.

For blunt bodies such as a circular cylinder or sphere, however, an increase in
the surface roughness may increase or decrease the drag coefficient depending
on the Reynolds number.
The effect of surface roughness on the drag coefficient of a sphere.
19
20

Flows across cylinders and
spheres, in general, involve flow
separation, which is difficult to
handle analytically.
Flow across cylinders and
spheres has been studied
experimentally by numerous
investigators, and several
empirical correlations have been
developed for the heat transfer
coefficient.
Variation of the local heat

transfer coefficient along the
circumference of a circular
cylinder in cross flow of air.
21
For flow over a cylinder
The fluid properties are evaluated at the film temperature
For flow over a sphere
The fluid properties are evaluated at the free-stream temperature T,

except for s, which is evaluated at the surface temperature Ts.
Constants C and m are
given in the table.
The relations for cylinders above are for single cylinders or
cylinders oriented such that the flow over them is not affected by
the presence of others. They are applicable to smooth surfaces.
22
23
24
FLOW ACROSS TUBE BANKS
Cross-flow over tube banks is commonly encountered in

practice in heat transfer equipment, e.g., heat
exchangers.
In such equipment, one fluid moves through the tubes
while the other moves over the tubes in a perpendicular
direction.
Flow through the tubes can be analyzed by considering
flow through a single tube, and multiplying the results by
the number of tubes.
For flow over the tubes, the tubes affect the flow pattern
and turbulence level downstream, and thus heat transfer
to or from them altered.
Typical arrangement: in-line or staggered in the direction
of flow.
The outer tube diameter D is the characteristic length.
The arrangement of the tubes is characterized by the
transverse pitch ST, longitudinal pitch SL, and the
diagonal pitch SD between tube centers.
25
Diagonal
pitch
Arrangement of the
tubes in in-line and
staggered tube
banks (A1, AT, and
AD are flow areas at
indicated locations,
and L is the length of
the tubes).
26
All properties except Prs are to

be evaluated at the arithmetic
mean temperature.
Correlations in Table 7-2
The average Nusselt number relations in Table 72 are for tube banks
with more than 16 rows. Those relations can also be used for tube
banks with NL < 16 provided that they are modified as
NL < 16
where F is a correction factor whose values are given in Table 73.
For ReD > 1000, the correction factor is independent of Reynolds number.
Log mean
temperature
difference
Exit temperature
Heat transfer
rate
27
28
Pressure drop
f is the friction factor and

c is the correction factor.
The correction factor c

given is used to account
for the effects of deviation
from square arrangement
(in-line) and from
equilateral arrangement
(staggered).
29
Summary
Drag and Heat Transfer in External Flow
Friction and Pressure Drag
Heat Transfer
Parallel Flow Over Flat Plates

Friction Coefficient
Flat Plate with Unheated Starting Length
Uniform Heat Flux
Flow Across Cylinders and Spheres

Effect of Surface Roughness
Flow Across Tube Banks

Pressure Drop
30

SI Heat 4e Chap07 Lecture PDF

Uploaded by

Copyright:

Available Formats

SI Heat 4e Chap07 Lecture PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SI Heat 4e Chap07 Lecture PDF

Uploaded by

Copyright:

Available Formats

Heat and Mass Transfer: Fundamentals & Applications

Fourth Edition in SI Units

Evaluate the drag and heat transfer associated with

DRAG AND HEAT TRANSFER IN EXTERNAL FLOW

Fluid flow over solid bodies frequently

Free-stream velocity: The velocity of the

It is usually taken to be equal to the

The fluid velocity ranges from zero at the

Friction and Pressure Drag

Drag: The force a flowing fluid exerts on a

The components of the pressure and wall

Both the skin friction (wall shear) and pressure

The part of drag that is due directly to wall

At low Reynolds numbers, most drag is

The friction drag is proportional to the

The pressure drag is proportional to the

The pressure drag is usually dominant

When a fluid separates from a body, it

Separated region: The low-pressure

Wake: The region of flow trailing

Average Nusselt number:

PARALLEL FLOW OVER FLAT PLATES

A generally accepted value for

The actual value of the engineering

Combined laminar + turbulent flow:

Heat Transfer Coefficient

These relations are for

The local friction and heat transfer

Nusselt numbers for average heat transfer coefficients

For liquid metals

Graphical representation of the average

Flat Plate with Unheated Starting Length

Average heat transfer coefficients

Flow over a flat plate

Uniform Heat Flux

These relations give values that are 36 percent higher for

FLOW ACROSS CYLINDERS AND SPHERES

At very low velocities, the fluid

Laminar boundary layer

Effect of Surface Roughness

This is especially the case for streamlined bodies.

The effect of surface roughness on the drag coefficient of a sphere.

Heat Transfer Coefficient

Variation of the local heat

For flow over a cylinder

The fluid properties are evaluated at the film temperature

For flow over a sphere

The fluid properties are evaluated at the free-stream temperature T,

FLOW ACROSS TUBE BANKS

Cross-flow over tube banks is commonly encountered in

All properties except Prs are to

Correlations in Table 7-2

f is the friction factor and

The correction factor c

Parallel Flow Over Flat Plates

Uniform Heat Flux

Flow Across Cylinders and Spheres

Flow Across Tube Banks

You might also like