Scribd
Upload
534 views4 pages

Distillation Version 3

This document provides details for an assignment to optimize a distillation column that separates a 1000 kmol/h feed of benzene and toluene. Students are asked to calculate the reflux ratio, R, that minimizes the equivalent annual operating cost (EAOC) of the column using specified equations. Results should be presented as two plots showing how the terms in the EAOC equation and the EAOC itself change with R/Rmin.

Uploaded by

Toru Lucis Caelum
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
534 views4 pages

Distillation Version 3

This document provides details for an assignment to optimize a distillation column that separates a 1000 kmol/h feed of benzene and toluene. Students are asked to calculate the reflux ratio, R, that minimizes the equivalent annual operating cost (EAOC) of the column using specified equations. Results should be presented as two plots showing how the terms in the EAOC equation and the EAOC itself change with R/Rmin.

Uploaded by

Toru Lucis Caelum
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

ChE 102

Spring 2011
Project #3
Distillation Column Optimization Version 3
Background
Distillation columns are used throughout the chemical industry to separate and purify products
using the difference in volatility of materials to effect the separation. The unit operation of
distillation usually involves several pieces of equipment that are shown in Figure 1.

O v e rh e a d C o n d e n s e r

4
D is t illa t io n T o w e r o r C o lu m n

cw
F IC

L IC

R e flu x D r u m
R e flu x P u m p

L IC

lp s

R e b o ile r
Figure 1: Illustration of the main pieces of equipment used in distillation

2
Feed material containing (for our case) two components with different boiling points are
introduced into the column in Stream 1. Heat in added to the column through a heat exchanger
(the reboiler) located at the bottom of the column, and heat is removed in the exchanger
(overhead condenser) located at the top of the column. In order for the column or tower to
operate properly, a portion of the top and bottom products must be returned or recycled to the
column. We refer to the amount of product (kmol/h) returned to the top of the tower as the reflux
and designate this as L. The top product, Stream 2, is usually referred to as D. Other notation
used to describe the process at the top of the column is given in Figure 2.
D
V

L
F
R = L /D
V = L + D = (1 + R )D
Figure 2: Illustration of top part of distillation column with stream notation
Project Details
When designing distillation columns, it is common to optimize the column using the reflux ratio,
R, as the design variable, where R is defined in Figure 2. The overall cost of building the
column and running it must be considered when optimizing the design. The capital investment
(cost) for the equipment includes the cost of the column, plus the costs of the reboiler, condenser,
reflux drum, and pump. For this project we will consider only the costs of the column and the
two heat exchangers (reboiler and condenser). The operating costs include the cost of the
cooling medium (water) for the condenser and the heating medium (steam) for the reboiler.
Because the equipment costs are one-time purchase costs and the operating costs (steam and
water) occur all the time, the time value of money must be taken into consideration when
defining an objective function. For this project we want to minimize the equivalent annual
operating cost (EAOC) of the column that is defined in Equation 1:

EAOC[$ / y ]

i 1

i 1

PCi [$]( A / P, i, n)[1/ y] UCi [$ / y]

(1)

where PCi are the purchase costs of the column and heat exchangers and UCi are the operating
(utility) costs (water and steam). You should assume that the effective annual interest rate, i, is
8% pa and that the length of the project, n, is 10 years.
Assignment
You are to optimize a distillation column (calculate the value of R that minimizes the EAOC)
that is to separate 1000 kmol/h of an equal molar feed of benzene and toluene into a top product
containing 99.5 mol% benzene with a recovery of benzene of 98%. The recovery of benzene is
the ratio of total amount (kmol) of benzene in the top product to that entering in the feed
(DyB/FzB, where zB is the feed mole fraction of benzene). The column is to operate at a pressure
of 1 atm. The term yB is the mole fraction of benzene in the top stream and xB is the mole fraction
of benzene in the bottom stream.
The relationship between the reflux ratio, R, and the number of stages or trays in the column, N,
is given by the following relationships:
yB 1 xB

xB 1 yB

ln
N min

ln

(2)

N N min
N 1

(3)

2
1

(4)

R Rmin
R 1

(5)

1 54.5 X X 1
Y 1 exp


11 117.2 X X

(6)

where is the relative volatility of the benzene with respect to the toluene, which is equal to 2.3
for this system. Material balances are required to determine xB. If you are not familiar with
material balances, you instructor will provide assistance.

4
The costs of utilities for the overhead condenser (cooling water = CW) and reboiler (steam) vary
with the cost of energy. Examine the range of costs shown in Table 1.
Table 1: Range of Parameters to Use for Utility Costs
Utility
Equation
Low Value
High Value
-7
UCCW [$/h ] aVV
cooling water
a = 0.2510
a = 210-7
UC steam [$/h ] bUCCW [$/h]
steam
b = 0.5
b=8
where V is the latent heat of vaporization kJ/kmol) of benzene at its normal boiling point and V
(kmol/h) is shown in Figure 2. The purchase cost of the column is given by:
0.85
PCcol $10, 000Vcol

(7)

where Vcol = d2L/4 is the volume of the column in m3 and d[m] and L[m] are the diameter and
height of the column, respectively. The diameter and height of the column are given by:

d [m] 0.15(V [kmol/h] ) 0.5

(8)

L[m] N

(9)

The purchase costs of the condenser and reboiler may be taken as 10% and 20% of the cost of
the column, respectively.
You should present your final results as two plots. The first should show how each term in
Equation 1 changes with R/Rmin, and the second plot should show the EAOC (y-axis) as a
function of R/Rmin (x-axis). Your report should contain a physical explanation of the reason for
the trends on these plots.

You might also like