DD501 Setup G03 081120

ASSEMBLY INSTRUCTIONS
Caution !
Watch your fingers when adjusting clamps. They may become pinched resulting in injury.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.
Inside This Package

Before assembly, please make sure that all the items listed below are present.
[Kick Trigger] box
[CYMBAL PADS] box

Cymbal Pad x 3
Beater
Foot Pedal
Kick Pad
[DRUM PADS] box

Tom Pad x 2
Snare Pad x 1
[ACCESSORIES] box
Cymbal holders (L & R)
Drumstick x 2
[DRUM MODULE and
HEADPHONES] box
Screws x4
for Drum Module
Cymbal holder
screwdriver
for Drum Module
Drum module
Metal Rod
AC Adaptor
HEADPHONES
Hexagon Key
Drum Key
Instruction Manual
Assembly Instructions
Stand
Round Seat
[HI-HAT PEDAL] box
Hi-Hat control pedal
Standard-gauge tubing
Double-Braced Legs
Assembly
1 Open the stand
[A]
[1]Tear off the adhesive tape on the stand.

[2] Loosen the wing nuts on the pillars.
[3] Open the stand in the order shown
in the illustration (A, B, C).
[4] Adjust the pillars height so that the
stand can locate steadily on the floor.
[5] Tighten the wing nuts on the pillars.
Tighten
Lossen
Wing nuts
Tear off the adhesive tape
[B]
adjust the
pillars height
[C]
2 Attaching the tom pads

[1] Insert the two tom pads into the
side arms respectively.
[2] Use a drum key to tighten the
screw on the bottom of tom pad.
[3] Adjust the side arms height so that
it does not interfere with other pads.
[4] Tighten the wing nuts on the pillars.
Insert the two tom

pads into the side
arms respectively.
side arm
Use a drum key to

tighten the screw on
the bottom of tom pad.
tighten the wing nut.
3 Attaching the snare pad

[1] Adjust the clamp position, then tighten
the wing nuts on the clamp.
[2] Use hexagon key to loosen the screw of
holder clamp.
[3] Insert the metal rod into the holder clamp
and adjust the position.
[4] Use hexagon key to tighten the screw of
holder clamp.
[5] Attach the snare pad to the metal rod and
adjust the position, then tighten the screw
on the snare pad.
use hexagon key to

loosen or tighten the
screw.
insert the metal rod into
the lock and adjust the
position.
attach the snare pad
to the metal rod.
tighten the
screw.
metal rod
4 Attaching the Drum Module

Use M4x15mm x2 screws
[1]Tear off the adhesive tape on the drum

module.
[2]Place the Drum Module on the drum
module holder, and use the included
screws to fasten it.
Use a
screwdriver
Tear off the adhesive tape
Use M4x25mm x2 screws
5 Attaching the cymbal pads

[1] Attach the Cymbal holders to the Holder
clamps on the arms.
[2] Use a drum key to tighten the screws on
the Holder clamps.
[3] Move out the wing nut and the felt washer
of each Cymbal holders.
[4] Attach the Cymbal pads to the cymbal
holders.
[5] Attach the felt washer and wing nut,
tighten the wing nut of each cymbal.
attach the cymbal holders

to the holder clamps arms.
use a drum key to
tighten the screws.
Wing nut
Felt washer
Cymbal holder
move out
Cymbal holder
Wing nut
Felt washer
attach and tighten
Cymbal pad
6 Attaching the Hi-Hat Control pedal

[1] Move out the pillar from the rubber foot.
[2] Attach the Hi-Hat control pedal to the
pillar.
attach the Hi-Hat
control pedal to
the pillar.
move out the

pillar from the
rubber foot.
7 Attaching the Kick Trigger

[1] Attach the Rod to the holders.
[2] Attach the Kick Pedal to the Kick Pad.
[3] Tighten the wing screw on the Kick Pedal.
[4] Loosen the screw.
[5] Attach the Beater to the Kick Pedal
[6] Position the Beater from the center of the pedal, tighten the screw
[3]
[1]
[1]
[2]
[4]
Beater
[6]
[9]
8 Attaching the Drum Throne

[1] Attach the standard-gauge tubing to the round seat.
[2] Tighten the wing nut on the round seat.
[3] Open the legs.
[4] Remove the wing nut and screw attached to the
Double-Braced Legs.
[5] Attach the standard-gauge tubing to the
Double-Braced Legs.
[6] Reattach the win nut and screw.
[7] Tighten the wing nut and screw.
[5]
9 Setup Example
Cymbal Pad
Drum Module
Tom Pad
Cymbal Pad
[4]
[3]
[3]
[5]
[1]
Snare Pad
[6],[7]
[3]
[2]
Hi-Hat control pedal
Kick Trigger
DD501_Setup_G03_081120

DD501 Setup G03 081120

Uploaded by

Copyright:

Available Formats

DD501 Setup G03 081120

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DD501 Setup G03 081120

Uploaded by

Copyright:

Available Formats

ASSEMBLY INSTRUCTIONS

Inside This Package

[CYMBAL PADS] box

[DRUM PADS] box

[1]Tear off the adhesive tape on the stand.

Tear off the adhesive tape

2 Attaching the tom pads

Insert the two tom

Use a drum key to

tighten the wing nut.

3 Attaching the snare pad

use hexagon key to

4 Attaching the Drum Module

[1]Tear off the adhesive tape on the drum

Use M4x25mm x2 screws

5 Attaching the cymbal pads

attach the cymbal holders

attach and tighten

6 Attaching the Hi-Hat Control pedal

move out the

7 Attaching the Kick Trigger

8 Attaching the Drum Throne

Hi-Hat control pedal

You might also like