Boiler Water LVL DP Cell

Instrumentation & Control
Chu/a/ongkom University
Chapter 1: INSTRUMENTATION El,JUlPMENT

Modu/e 4: Leve/lnstrumentation
CHAPTER 1: INSTRUMENTATION EQUIPMENT

MODULE 4: Level Instrumentation
MODULE OBJECTIVES:
At the end of this module, you will be able to:
,
1.
Sketch and explain the principle of an open tank level measurement installation using a level
transmitter.
.
2.
Sketch and explain the principle of a closed tank level measurement installation using a level
transmitter and dry leg.
3.
Explain the purpose of a tlnee-valve manifold in closed tank level measurement installations.
4.
State the procedure required for valving a level transmitter:

a) into service, and
b) out of service
when a three valve manifold is used.
5.
Briefly explain the principle of operation of a closed tank, wet leg, level measurement installation.
6.
Briefly explain the need for

a} zero suppression, and
b) zero elevation
in level measurement installations by reference to an example process application for each case.
7.
Briefly explain the principle of operation of a bubbler level measurement system.
8.
List two advantages of a bubbler system.

page1-4-1
Chapter 1: INSTRUMENTATlON E:... JIPMENT

Module 4: Levellnstromentation
Instromental/un & Control

Chulalongkom University
Inferential Level Measurement

Inferential level measurement techniques obtain a level indication
exerted by the column of liquid.
n_~
r -
~.
iru:ti~
by monitoring the presslJre
u
n
where
P Pressure (Pa)
5 Weight density of the liquid (N/m 3)
H = Height of liquid column (m)
=
=
Open Tank Application

The high pressure side of the level
transmitter is connected to the base of the
tank while the low pressure side is vented to
atmosphere.
Phigh
~P
Vented to
Atmosphere
T
H
=Palm + 5 . H
Differential pressure
=P
high -
Plow
=5 . H
The level transmitter can be calibrated to

output 4 mA when the tank is at 0% level and
20 mA when the tank is at 100% level.
HP,,-- LP"
flo.... .A
~
Weight Density
Valve
LT
1--....
\. Y
L
-~
4-20mA
Signal
Figure 1: Open Tank Level Measurement Installation.
page1-4-2
Chapter 1: INSTRUMENTA TION e",JIPMENT

Module 4: Level Instrumentation

Closed Tank Application

Should the tank be closed, and a gas
phase exist on top of the liquid, the
rtI"31!'
~W~
'04 ..... 111"'_'"

nroC!-C!-lIra
rnllC!+ ho
"'1
11 ..... _ _ _ _ _
,...n""n.o.nC!~+orl
for.
A change in the gas pressure will
cause a change in transmitter output.
The pressure exerted by the gas
phase may be so high that the
hydrostatic pressure of the liquid
column becomes insignificant
Compensation can be achieved by
applying the gas pressure to both the
high and low pressure sides of the
level transmitter.
. /Pgas
"
Isolation
Valve
Low Pressure
ImpUlse Line
L_~
4-20mA
Signal
Figure 2: Typical Closed Tank Level Measurement System.
We have:
Phl9h = Pgas + S . H
Plow= Pgas
AP = Phigh - Plow = S . H
The effect of the gas pressure is canceled and only the pressure due to the hydrostatic head of the liquid
is sensed.
When the low pressure impulse line is connected directly to the gas phase above the liquid level, it is
calleda~
page1-4-3
Chapter 1: /NSTRUMENTA TlON Er.,v/PMENT

Module 4: Leve/lnstrumentation
Instrumentat/un & Control

Chu/alongkom University
Three Valve Manifold

Applying excessive pressure to a DP capsule is called overranging, which could damage the capsule.
A three valve rn..a..n.i.fQld is a device that is used to ensure that the capsule will not be over-ranged. It also
allows isolation of the transmitter from the process loop. It consists of
- two block valves - high pressure and low pressure block valve
- and an equalizing valve.
Process
High Pressure
Side
Process
Low Pressure
Side
During normal operation, the

equalizing valve is closed and
the two block valves are open.
3 Valve
Manifold
When the tri:!nsmitter is put

into or removed from service,
the valves must be operated in
such a manner that the high
pressure gas phase is never
applied to only one side of the
DP capsule.
-~
Signal
Figure 3: A Three Valve Manifold.
page1-4-4
Chaptf)r 1: INSTRUMENTA TlON E<..,<JIPMENT

InstrumentatIon & Control

Operational Sequences of Three-Valve Manifold Valving Transmitter Into Service

To valve the DP transmitter into service, the following steps should be followed:
1.
Check all valves closed.
2.
Open the equalizing valve - this ensures that the same pressure will be applied to both sides of
the transmitter, i.e. zero differential pressure.
3.
Open the High Pressure block valve slowly, check for leakage from both the high pressure and
low pressure side of the transmitter.
4.
Close the equalizing valve - this locks the pressure on both sides of the transmitter.
5.
Open the low pressure block valve to apply process pressure to the low pressure sides of the
transmitter and establishes the working differential pressure.
The transmitter is now in service.

Note it may be necessary to bleed any trapped air from the capsule housing.
Removing Transmitter From Service (reversal of the above steps):
1.
Close the low pressure block valve.
2.
Open the equalizing valve.
3.
Close the high pressure block valve.
page1-4-5

Chu/alongkorn University
Chapter 1: /NSTRUMENTATION E.... _.PMENT

Module 4: Leve/lnstrumentation
Dry Leg System

If the gas phase is condensable, such as
steam, condensate may form in the low
pressure impulse line iesulting in a column
of liquid which exerts extra pressure on the
low pressure side of the transmitter.
isolating
(H~g.8H'}-rXI_e_--l
Isolating
Valve
A technique to solve this problem is to add a

knock-out pot below the transmitter in the
low pressure side.
Low Pressure
Impulse Line
3 Valve
Manifold
Periodic draining of the condensate in the

knock-out pot will ensure that the impulse
line is free of liquid.
High
A disadvantage of th'3 dry leg that restricts

its use is the frequent maintenance that is
required.
Isolating Valve
(Normally Open)
Knock-out
Pot
Isolating Valve
(Normally Closed)
Figure 4: Dry Leg Installation with a Three Valve Manifold.
page1-4-6
Chapter 1: INSTRUMENTATION Ec.,...,IPMENT

Modu!e 4: Leve/lnstrumentation

Chula/ongkorn University
Wet Leg System
Sloped Towards
Main Tank - -__
In a wet leg system, the low pressure impulse

line is completely filled with liquid (usually the
same iiquid as the process;, and hence the
name "wet leg"..
Pressure
Release Valve
C-atch
Tank
Pgaa
A level transmitter, with the associated three

valve manifold, is used in an identical manner to
the dry leg system.
The gas phase or vapour will condense in the
wet leg and the catch tank.
Steam or
The catch tank, with the inclined interconnecting

line, maintains a constant hydrostatic pressure
on the low pressure side of the level transmitter.
This pressure, being a constant, can easily be
compensated for by calibration.
Electric
Heating
",
Drain Valves
3 Valve
Manifold
Transmitter
Drain Valves
Figure 5: A Wet Leg Installation.
page1-4-7
Chapter 1: INSTRUMENTA TlON El.,<JIPMENT

InstrumentarMl & Control

Zero Suppression
In some cases, the level transmitter has
to be mounted X meters below the base of
The liquid in the high pressure impulse

line exerts a constant pressure (P = S .
X) on the high pressure side.
When the liquid level is at H meters,
pressure on the high pressure side of
the transmitter will be:
;::::;; :
T
H
Isolating
Valve
H.P. Impulse line
Xrn
Phl9h =SH+S,X+Patm
Plow = Patm
~P = Phlgh - Plow == S . H + S . X
The transmitter has to be negatively
biased by a value of -S . X so that the
output of the transmitter is proportional to the
tank level (S . H) only.
Vented to
Atmosphere
LP
Figure 6: Level Transmitter with Zero Suppression.
The above procedure is called Zero Suppression and it can be done during calibration of the transmitter.
page 1-4-8
Chapter 1: INSTRUMENTATION E<.,,,,PMENT


Zero Elevation
Note that (see Figure 7), the height of
the wet leg (X) is always equal to or
. . . . . . . - ,.
greater man me maximum nelgm OT me
liquid column (H) inside the tank.
.. ..
In a wet leg installation the low

pressure side of the level transmitter
will always experience a higher
pressure than the high pressure side.
When the liquid level is at H meters, we
have:
=P
Plow =P
Ph1gh
gas
gas
STEAM
L.P.
IMPULSE
(p g,.)
LINE filled
withHaO
Xm
Hm
HOT WATER
+S.H
+S .X
bP = Phlgh - Plow = S . H - S . X = -S(X . H)
The differential pressure bP sensed by

the transmitter is always a negative
number (i.e. low pressure side is at a
higher pressure than high pressure
side).
WATER
INLET
Figure 7: Simplified Wet Leg Installation.
To properly calibrate the transmitter, a

positive bias (S . X) is needed to elevate the transmitter output. This positive biasing technique is called
zero elevation.
page1-4-9
Chapter 1: INSTRUMENTA TION EI... _.:>MENT


Bubbler Level Measurement System

This system of level measurement is
used when the process liquid cannot be
direct contact with the level transmitter.
The system operates as follows:
A bubbler tUbe is immersed to the
bottom of the vessel in which the
liquid level is to be measured. A gas
(called purge gas) is allowed to pass
through the bubbler tUbe.
When the tank is empty. the gas will
escape freely at the end of the tUbe
and therefore the gas pressure inside
the bubbler tube (called back
pressyre) will be at atmospheric
pressure.
CONSTANT DIFFERENTIAl
PRESSURE RElAY
=oz#."-I)\(J6=====;~===="iF=====o#====1H
L I==)I~ Atmosphere
Vented to
"IU''''''~
"A~
r'"'n....
~~
. SUPPLY
I,"-+-- BUBBLER
TUBE
- .H
-_-_1_-_-_-_:.._-1
REFERENCE - - .....
Figure 8: Bubbler Level Measurement System in an Open Tank.
As the liquid level inside.the tank increases, pressure exerted by the liquid at base of the tank and at the
opening of the bubbler tube increases. The gas pressure in the bubbler tube will continue to increase
until it just balances the hydrostatic pressure (P = S . H) of the liquid. At this point the back pressure in
the bubbler tUbe is exactly the same as the hydrostatic pressure of the liquid and it will remain constant
until any change in the liquid level occurs.
Any excess supply pressure will escape as bubbles through the liquid.
An additional advantage of the bubbler system is that since it measures only the back pressure of the
purge gas, the exact location of the level transmitter is not important. The transmitter can be mounted
some distance from the process.
page 1 - 4 - 10

Boiler Water LVL DP Cell

Uploaded by

Copyright:

Available Formats

Boiler Water LVL DP Cell

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boiler Water LVL DP Cell

Uploaded by

Copyright:

Available Formats

Instrumentation & Control

Chapter 1: INSTRUMENTATION El,JUlPMENT

CHAPTER 1: INSTRUMENTATION EQUIPMENT

State the procedure required for valving a level transmitter:

Briefly explain the need for

Briefly explain the principle of operation of a bubbler level measurement system.

List two advantages of a bubbler system.

Chapter 1: INSTRUMENTATlON E:... JIPMENT

Instromental/un & Control

Inferential Level Measurement

by monitoring the presslJre

Open Tank Application

The level transmitter can be calibrated to

Figure 1: Open Tank Level Measurement Installation.

Chapter 1: INSTRUMENTA TION e",JIPMENT

Instrumentation & Control

Closed Tank Application

'04 ..... 111"'_'"

Chapter 1: /NSTRUMENTA TlON Er.,v/PMENT

Instrumentat/un & Control

Three Valve Manifold

During normal operation, the

When the tri:!nsmitter is put

Figure 3: A Three Valve Manifold.

Chaptf)r 1: INSTRUMENTA TlON E<..,<JIPMENT

InstrumentatIon & Control

Operational Sequences of Three-Valve Manifold Valving Transmitter Into Service

Check all valves closed.

The transmitter is now in service.

Close the low pressure block valve.

Open the equalizing valve.

Close the high pressure block valve.

Instrumentation & Control

Chapter 1: /NSTRUMENTATION E.... _.PMENT

Dry Leg System

A technique to solve this problem is to add a

Periodic draining of the condensate in the

A disadvantage of th'3 dry leg that restricts

Chapter 1: INSTRUMENTATION Ec.,...,IPMENT

Instrumentation & Control

Wet Leg System

In a wet leg system, the low pressure impulse

A level transmitter, with the associated three

The catch tank, with the inclined interconnecting

Chapter 1: INSTRUMENTA TlON El.,<JIPMENT

InstrumentarMl & Control

The liquid in the high pressure impulse

H.P. Impulse line

Figure 6: Level Transmitter with Zero Suppression.

Chapter 1: INSTRUMENTATION E<.,,,,PMENT

Instrumentation & Control

In a wet leg installation the low

bP = Phlgh - Plow = S . H - S . X = -S(X . H)

The differential pressure bP sensed by

Figure 7: Simplified Wet Leg Installation.

To properly calibrate the transmitter, a

Chapter 1: INSTRUMENTA TION EI... _.:>MENT

Instrumentation & Control