Scribd
Upload
552 views4 pages

TRIO Manual en

power source

Uploaded by

mihailmi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
552 views4 pages

TRIO Manual en

power source

Uploaded by

mihailmi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

TruePower Trio

Models: TP3-430, TP3-550, TP3-650

Users Manual
Manuel de lutilisateur
Anwenderhandbuch
Manuale per loperatore
Manual del usuario

Antec TruePower Trio Users Manual


ATX12V version 2.2 power supply
Models: TP3-430, TP3-550, TP3-650
The TruePower Trio series comply with the ATX12V version 2.2 (EPS12V for
TP3-550 and TP3-650) specifications. This includes three +12V outputs that
deliver safer and more reliable power to your systems components. With up to
85% efficiency, the power supply helps save energy and money on your electrical
bill compared to typical power supplies. TruePower Trio power supplies generate
less heat because of their high efficiency and thus keep the power supply itself
cooler and prolong its life. They also include a variety of industrial-grade protective
circuitry: OPP (over power protection), OVP (over voltage protection), SCP (short
circuit protection), and UVP (under voltage protection).
Connectors: TruePower Trio has a 24-pin main connector with detachable 4-pin
section, a 4-pin +12V connector for single CPU systems, and a 8-pin +12V
connector for multi CPU systems (TP3-550 and TP3-650). All models include six
4-pin peripheral connectors, four 15-pin SATA connectors, one floppy connector,
and PCI-Express Connectors (two for TP3-550 and TP3-650; one for TP3-430).
The power supply has an advanced temperature response system that provides
optimum balance between noise reduction and cooling. The 120mm quiet fan will
always run at the lowest speed possible for existing load and conditions.
In addition, it can control the speed of your system case fans. You can find two
fan connectors (marked Fan Only) to which you can connect your system case
fans. TruePower Trio will then regulate your case fans, further reducing system
noise. Note: Do not connect more than two external fans to the Fan Only
connectors. Also, Antec DOES NOT recommend connecting a CPU fan to the Fan
Only connectors.
TruePower Trio power supplies include Universal Input and Active Power Factor
Correction (PFC). Universal Input allows you to connect TruePower Trio power
supply to any AC power input between 100~240V, without having to worry
about setting a voltage switch. Active PFC improves the power factor value of the
power supply by altering the input current wave shape and thus helps the power
plant to provide power to users more efficiently.
Power Switch: This power supply comes with a main power switch. Make sure
you turn the switch to the ON ( I ) position before you boot up your computer for
the first time. In normal operation there is no need to turn the switch to the OFF
(O) position since the power supply is equipped with a soft on/off feature which
turns your computer on and off through the soft switch on your computer case.
You may need to turn the switch to the OFF position occasionally should your
computer crash and you cannot shut it down through use of the soft switch.
Installation:
This power supply is backwards-compatible to previous ATX12V specifications.
To make sure you connect your power supply properly, please refer to the user
manuals supplied with your motherboard and peripherals before connecting the
TruePower Trio to any of your devices.
1

1.
2.

Disconnect the power cord from your old power supply.


Open your computer case, following the directions provided in your case
manual.
3. Disconnect all power connectors from the motherboard and from peripherals
devices such as case fans, hard drives, optical drives, floppy drives, etc.
4. Remove the existing power supply from your computer case and replace it
with your new Antec power supply.
Picture 1
Picture 2
5. Connect the 24-pin Main Power Connector. If your
motherboard uses a 20-pin connector, detach the
4-pin attachment on the 24-pin power connector (see
pictures 1 and 2).
Note: the detachable 4-pin section cannot be used in
place of the 4-pin +12V connector.
6. For TP3-430, connect the 4-pin +12V connector.
For TP3-550 and TP3-650, if you are using single CPU system, just connect
the 4-pin +12V connector. If you are using dual CPUs system or a system
that requires the 8-pin +12V connector, use the 8-pin +12V connector
(Note: some high end single CPU motherboards may require an 8-pin +12V).
7. Connect the 4-pin peripheral connectors to the peripheral devices such as
optical drives and hard drives.
8. Optional: If youd like to monitor the speed of the power supply fan, connect
the 3-pin fan signal connector to one of the fan connectors on your
motherboard.
Note: You dont need to connect the fan signal connector in order for the
power supply to work.
9. Connect the 15-pin SATA connectors to your SATA hard drives as needed.
10. Connect the 6-pin PCI Express connectors marked PCI-E to your PCI Express
graphic cards if needed.
Note: Please consult the user manual supplied with your PCI Express graphic
card for detailed usage instructions.
11. Connect the power cord to the power supply.

Antec, Inc.
47900 Fremont Blvd.
Fremont, CA 94538
USA
tel: 510-770-1200
fax: 510-770-1288

Antec Europe B.V.


Stuttgartstraat 12
3047 AS Rotterdam
The Netherlands
tel: +31 (0) 10 462-2060
fax: +31 (0) 10 437-1752

Customer Support:
US & Canada
1-800-22ANTEC
[email protected]

Europe
+31 (0) 10 462-2060
[email protected]

www.antec.com

Copyright 2007 Antec, Inc. All rights reserved.


All trademarks are the property of their respective owners.
Reproduction in whole or in part without written permission is prohibited.
Printed in China.

You might also like