Connect Network Monitoring via no-ip
1. Register on the no-ip website and fill in registration information.
2. Download and install the no-ip client software.
3. Fill in the applied dynamic domain name in the client to access the network monitoring device remotely.
Connect Network Monitoring via no-ip
1. Register on the no-ip website and fill in registration information.
2. Download and install the no-ip client software.
3. Fill in the applied dynamic domain name in the client to access the network monitoring device remotely.
Connect Network Monitoring via no-ip
1. Register on the no-ip website and fill in registration information.
2. Download and install the no-ip client software.
3. Fill in the applied dynamic domain name in the client to access the network monitoring device remotely.
Connect Network Monitoring via no-ip
1. Register on the no-ip website and fill in registration information.
2. Download and install the no-ip client software.
3. Fill in the applied dynamic domain name in the client to access the network monitoring device remotely.
1. Enter the no-ip official website for registration http://www.noip.
com/ (no-ip official website) 2. Click to register i (as the red part shown below) and fill in the registration information.
Note: (1) The password should be simple but not too complex (2) After registration, no-ip will send an activation email immediately:
Click the link to confirm activation
3.ClickDownload,and then chooseDownload Now (As the blue
part shown below ) Web: https://www.noip.com/downloads.php?page=win
4. Download the client software (https://www.noip.com/downloads.
php?page=win) as below picture.
5. Install the client.
6. Fill in the applied domain name.
7. Fill in the dynamic domain name you have applied http://ansjer.
no-ip.biz/ for access to your device.
Connect Network Monitoring via Meibu
1.Enter meibu official website for registration http://www.meibu.com// (meibu official website)
2. Click to register (As the red part shown above).
Note :(1) The password should be simple but not too complex; (2) After registration ,Meibu will send a free domain name.
3. Click and choose "software download software" (Shown below
in blue:) Web: http://www.meibu.com/khd.asp
4. Download the client software (http://www.meibu.com/khd.asp) as
below picture.
5. Install the client.
6. Fill in the applied domain name.
7. Fill in the dynamic domain name you have applied http://
ansjertest.meibu.net/ for access to your device.
How to set your router parameters
1. Click the bottom left of your computer
input ipconfig/all(This step is to
obtain the network parameters through the computer, providing network parameters for the next DVR setting)
Note: 192.168.0.106: (This is the IP address of the computer, Please set the IP address of the DVR to be: 192.168.0.XXX (XXX ranges from 2 to 254, but can not be 106, otherwise the IP of DVR will conflict with that of the computer which will lead DVR can not remote login ). 255.255.255.0: The subnet mask of DVR is the same to this setting. 192.168.0.1: Gateway of DVR is the same to this setting. 192.168.0.1: The DNS of DVR is the same to this setting. Note: If can not set successfully, please enter the gateway through the IE browser and login router to view the correct DNS in the operating status.. HTTP port: Here cantt be set as 80, otherwise it will cause the port confliction Server port: Common use low port such as: 3000, 6000, etc.
2. Network parameters of DVR are as following:
10
3. Set DVR DDNS
Click [main menu] [Configuration Management] [Network Configuration] [more configuration] to enter setup interface:
[Dynamic Domain Name Service] After ticking and choosing, it will enable. [Dynamic Domain Name Server] Select the Domain Name Server which the device supports [User name] Fill in the registered name when applying dynamic domain name [Password] Fill in the set password when applying dynamic domain name [Host Domain name] Fill in the applied dynamic domain name. [Test] After clicking to test the filled in information is correct or not After finishing setting, save and exit.
