Cisco Dpc3828

O
L- 2 9 1 5
9 -0 1
Cisco Model DPC3828/EPC3828

DOCSIS/EuroDOCSIS 3.0 8x4
Wireless Residential Gateway
User Guide
Please Read
Important
Please read this entire guide. If this guide provides installation or operation
instructions, give particular attention to all safety statements included in this guide.
Notices
Trademark Acknowledgments
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its
affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. DOCSIS is a registered trademark of Cable
Television Laboratories, Inc. EuroDOCSIS, EuroPacketCable, and PacketCable are
trademarks of Cable Television Laboratories, Inc. The Wi-Fi Protected Setup mark is
a mark of the Wi-Fi Alliance. Wi-Fi Protected Setup is a trademark of the Wi-Fi
Alliance.
Other third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between
Cisco and any other company. (1110R)
Publication Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that may
appear in this publication. We reserve the right to change this publication at any
time without notice. This document is not to be construed as conferring by
implication, estoppel, or otherwise any license or right under any copyright or
patent, whether or not the use of any information in this document employs an
invention claimed in any existing or later issued patent.
Disclaimer
The maximum performance for wireless is derived from IEEE Standard 802.11
specifications. Actual performance can vary, including lower wireless network
capacity, data throughput rate, range and coverage. Performance depends on many
factors, conditions and variables, including distance from the access point, volume of
network traffic, building materials and construction, operating system used, mix of
wireless products used, interference and other adverse conditions.
Software and Firmware Use

The software described in this document is protected by copyright law and
furnished to you under a license agreement. You may only use or copy this software
in accordance with the terms of your license agreement.
The firmware in this equipment is protected by copyright law. You may only use the
firmware in the equipment in which it is provided. Any reproduction or distribution
of this firmware, or any portion of it, without our express written consent is
prohibited.
Copyright
2013 Cisco Systems, Inc. All rights reserved. Printed in the United States of
America.
Information in this publication is subject to change without notice. No part of this
publication may be reproduced or transmitted in any form, by photocopy,
microfilm, xerography, or any other means, or incorporated into any information
retrieval system, electronic or mechanical, for any purpose, without the express
permission of Cisco Systems, Inc.
Contents
IMPORTANT SAFETY INSTRUCTIONS
vii
United States FCC Compliance
xi
CE Compliance
xiii
Chapter 1 Introducing the DOCSIS Wireless Residential Gateway 1

Introduction ......................................................................................................................... 2
What's In the Carton? .......................................................................................................... 3
Front Panel Description ...................................................................................................... 4
Back Panel Desc ription ....................................................................................................... 5
Chapter 2 Installing the DOCSIS Wireless Residential Gateway
Installation P reparations ..................................................................................................... 8

Install the Wireless Res idential Gateway ........................................................................ 13
Chapter 3 Operation of Front Panel Indicators
17
Initial Power Up, Calibration, and Registration (AC Power Applied).......................... 18

Normal Op erations (AC Power Applied) ....................................................................... 20
Special Conditions ............................................................................................................. 21
Chapter 4 Troubleshooting the DOCSIS Wireless Residential

Gateway
23
Frequently Asked Questions ............................................................................................ 24

Common Troubles hooting Issues .................................................................................... 29
Tips for Improved Performa nce ....................................................................................... 30
OL-29 159 -01
Chapter 5 Customer Information
31
Index
33
iii
Notice to Installers
The servicing instructions in this notice are for use by qualified service personnel only. To reduce the
risk of electric shock, do not perform any servicing other than that contained in the operating
instructions, unless you are qualified to do so.
Notice lattention des installateurs de rseaux cbls

Les instructions relatives aux interventions dentretien, fournies dans la prsente notice, sadressent
exclusivement au personnel technique qualifi. Pour rduire les risques de chocs lectriques, neffectuer
aucune intervention autre que celles dcrites dans le mode d'emploi et les instructions relatives au
fonctionnement, moins que vous ne soyez qualifi pour ce faire.
Mitteilung fr CATV-Techniker
Die in dieser Mitteilung aufgefhrten Wartungsanweisungen sind ausschlielich fr qualifiziertes
Fachpersonal bestimmt. Um die Gefahr eines elektrischen Schlags zu reduzieren, sollten Sie keine
Wartungsarbeiten durchfhren, die nicht ausdrcklich in der Bedienungsanleitung aufgefhrt sind,
auer Sie sind zur Durchfhrung solcher Arbeiten qualifiziert.
Aviso a los instaladores de sistemas CATV

Las instrucciones de reparacin contenidas en el presente aviso son para uso exclusivo por parte de
personal de mantenimiento cualificado. Con el fin de reducir el riesgo de descarga elctrica, no realice
ninguna otra operacin de reparacin distinta a las contenidas en las instrucciones de funcionamiento, a
menos que posea la cualificacin necesaria para hacerlo.
2 0 0 8 0 8 1 4 _Insta ller8 2 0 _ Intl

1)
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding-type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10
)
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11
)
Only use attachments/accessories specified by the manufacturer.
12
)
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13
)
Unplug this apparatus during lightning storms or when unused for long periods of
time.
14
)
Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as a power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
Power Source Warning

A label on this product indicates the correct power source for this product. Operate this product only
from an electrical outlet with the voltage and frequency indicated on the product label. If you are
uncertain of the type of power supply to your home or business, consult your service provider or your
local power company.
The AC inlet on the unit must remain accessible and operable at all times.
OL-29 159-01
vii
Ground the Product

WARNING: Avoid electric shock and fire hazard! If this product connects to coaxial
cable wiring, be sure the cable system is grounded (earthed). Grounding provides
some protection against voltage surges and built-up static charges.
Protect the Product from Lightning

In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.
Verify the Power Source from the On/Off Power Light

When the on/off power light is not illuminated, the apparatus may still be connected to the power
source. The light may go out when the apparatus is turned off, regardless of whether it is still plugged
into an AC power source.
Eliminate AC Power/Mains Overloads

WARNING: Avoid electric shock and fire hazard! Do not overload AC power/mains,
outlets, extension cords, or integral convenience receptacles. For products that require
battery power or other power sources to operate them, refer to the operating
instructions for those products.
Provide Ventilation and Select a Location

Remove all packaging material before applying power to the product.
Do not place this apparatus on a bed, sofa, rug, or similar surface.
Do not place this apparatus on an unstable surface.
Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation
provides proper ventilation.
Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or
other objects on top of this product.
Do not block ventilation openings.
Operating Environment
This product is designed for operation indoors with a temperature range from 32 to 104 F (0 to 40C).
Each product should have adequate spacing on all sides so that the cooling air vents on the chassis are
not blocked.
viii
OL-29159-01
Protect from Exposure to Moisture and Foreign Objects

WARNING: Avoid electric shock and fire hazard! Do not expose this product to
dripping or splashing liquids, rain, or moisture. Objects filled with liquids, such as
vases, should not be placed on this apparatus.
WARNING: Avoid electric shock and fire hazard! Unplug this product before cleaning.
Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning
device (dust remover) to clean this product.
WARNING: Avoid electric shock and fire hazard! Never push objects through the
openings in this product. Foreign objects can cause electrical shorts that can result in
electric shock or fire.
Service Warnings
WARNING: Avoid electric shock! Do not open the cover of this product. Opening or
removing the cover may expose you to dangerous voltages. If you open the cover, your
warranty will be void. This product contains no user-serviceable parts.
Check Product Safety

Upon completion of any service or repairs to this product, the service technician must perform safety
checks to determine that this product is in proper operating condition.
Protect the Product When Moving It

Always disconnect the power source when moving the apparatus or connecting or disconnecting
cables.
OL-29 159 -01
ix

This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against such interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy. If not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment OFF and ON, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Consult the service provider or an experienced radio/television technician for help.
Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Any changes or modifications not expressly approved by Cisco Systems, Inc., could void the
user's authority to operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below is a
requirement of the FCC and is intended to supply you with information regarding the FCC
approval of this device. The phone numbers listed are for FCC-related questions only and not
intended for questions regarding the connection or operation for this device. Please contact your
service provider for any questions you may have regarding the operation or installation of this device.
Declaration of Conformity
This device complies with Part 15 of FCC
Rules. Operation is subject to the following
two conditions: 1) the device may not cause
harmful interference, and 2) the device must
accept any interference received, including
interference that may cause undesired
operation.
DOCSIS Wireless Residential Gateway

Model(s): DPC3828 EPC3828
Manufactured by:
Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 770 236-1077
Canada EMI Regulation

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numrique de la class B est conforme la norme NMB-003 du Canada.
RF Exposure Statements
Note: This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with a minimum
distance of 7.9 inches (20 cm) between the radiator and your body.
OL-29 159 -01
xi
US
This system has been evaluated for RF exposure for humans in reference to ANSI C 95.1
(American National Standards Institute) limits. The evaluation was based in accordance with
FCC OET Bulletin 65C rev 01.01 in compliance with Part 2.1091 and Part 15.27. The minimum
separation distance from the antenna to general bystander is 7.9 inches (20 cm) to maintain
compliance.
Canada
This system has been evaluated for RF exposure for humans in reference to Canada Health
Code 6 (2009) limits. The evaluation was based on evaluation per RSS-102 Rev 4. The
minimum separation distance from the antenna to general bystander is 7.9 inches (20 cm) to
maintain compliance.
2 0 1 0 0 5 2 7 FCC DSL_ Domestic
x ii
OL-29159-01
CE Compliance
CE Compliance
Declaration of Conformity with Regard to the EU Directive 1999/5/EC
(R&TTE Directive)
This declaration is only valid for configurations (combinations of software, firmware and
hardware) supported or provided by Cisco Systems for use within the EU. The use of
software or firmware not supported or provided by Cisco Systems may result in the
equipment no longer being compliant with the regulatory requirements.
OL-29 159 -01
x iii
CE Compliance
Note: The full declaration of conformity for this product can be found at
http://www.cisco.com/ we b/co nsumer/ support/ compliance_info.htm l.
The following standards were applied during the assessment of the product against the
requirements of the Directive 1999/5/EC:
Radio: EN 300 328

EMC: EN 301 489-1 and EN 301 489-17
Safety: EN 60950 and EN 50385
The CE mark and class-2 identifier are affixed to the product and its packaging. This product
conforms to the following European directives:
-1999/5/EC
National Restrictions
This product is for indoor use only.
France
For 2.4 GHz, the output power is restricted to 10 mW EIRP when the product is used
outdoors in the band 2454 - 2483.5 MHz. There are no restrictions when used in other parts of
the 2.4 GHz band. Check http://www.arcep.fr/ for more details.
Pour la bande 2,4 GHz, la puissance est limite 10 mW en p.i.r.e. pour les quipements
utiliss en extrieur dans la bande 2454 - 2483,5 MHz. Il n'y a pas de restrictions pour des
utilisations dans d'autres parties de la bande 2,4 GHz. Consultez http://www.arcep.fr/ pour
de plus amples dtails.
Italy
This product meets the National Radio Interface and the requirements specified in the
National Frequency Allocation Table for Italy. Unless this wireless LAN product is operating
within the boundaries of the owner's property, its use requires a general authorization.
Please check http://www.comuni cazi oni.it/i t/ for more details.
Questo prodotto conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano
Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all 'interno del
proprio fondo, l'utilizzo di prodotti Wireless LAN richiede una Autorizzazione Generale.
Consultare http://www.comuni cazi oni.it/i t/ per maggiori dettagli.
Latvia
The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic
Communications Office. Please check http://www.esd.lv for more details.
2,4 GHz frekvenu joslas izmantoanai rpus telpm nepiecieama atauja no Elektronisko
sakaru direkcijas. Vairk informcijas: http://www.esd.lv.
Note: The regulatory limits for maximum output power are specified in EIRP. The EIRP level
of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the
output power available at the connector (specified in dBm).
x iv
OL-29159-01
CE Compliance
Antennas
Use only the antenna supplied with the product.
2 0 1 1 0 3 1 1 _CE_ Gatewa y
OL-29 159 -01
xv
1 Chapter 1
Introducing the DOCSIS
Purpose
This guide covers the following product models:
DPC3828 DOCSIS Wireless Residential Gateway
EPC3828 DOCSIS Wireless Residential Gateway
All features described in this guide are standard to these models of
residential gateways unless otherwise noted. For the purpose of this
guide, whenever a feature or option applies to only a specific model,
the model number is specified. If a model number is not specified,
then the feature or option applies to both of the models.
e
This guide is written for the home subscriber.
nt Version
This is the first formal release of this document.
In This Chapter
OL-29 159 -01
Introduction ..........................................................................................2
What's In the Carton? ...........................................................................3
Front Panel Description .......................................................................4
Back Panel Desc ription ........................................................................5
Chapter 1 Introducing the DOC SIS Wireless Residential Gateway
Introduction
Your new Cisco Model DPC3828 DOCSIS 3.0 or EPC3828 EuroDOCSIS Wireless
Residential Gateway meets industry standards for high-speed data connectivity.
This residential gateway delivers data and wired (Ethernet) or wireless gateway
capabilities to connect a variety of devices in the home or small office and support
high-speed data access and cost-effective voice services, all in one device.
This guide provides procedures and recommendations for installing, operating, and
troubleshooting your residential gateway for high-speed Internet service. Contact
your service provider for more information about subscribing to these services.
Your new residential gateway offers the following outstanding benefits and features:
Compliant with DOCSIS and EuroDOCSIS 3.0, 2.0, and 1.x standards along with
PacketCable and EuroPacketCable specifications to deliver high-end
performance and reliability
High performance broadband Internet connectivity to energize your online
experience
Four 1000/100/10BASE-T Ethernet ports to provide wired connectivity
802.11n Wireless Access Point
User configurable Parental Control blocks access to undesirable Internet sites
Advanced firewall technology deters hackers and protects the home network
from unauthorized access
Attractive compact design that allows for vertical, horizontal, or wall-mounted
operation
Color-coded interface ports and corresponding cables simplify installation and
setup
DOCSIS-5 compliant LED labeling and behavior provides a user and technician
friendly method to check operational status and act as a troubleshooting tool
Allows automatic software upgrades by your service provider
OL-29159-01
What's In the Carton?
What's In the Carton?

When you receive your residential gateway, you should check the equipment and
accessories to verify that each item is in the carton and that each item is undamaged.
The carton contains the following items:
One DPC3828 or EPC3828 DOCSIS

One power adapter (models requiring
external power supply)
One Ethernet cable (May not be

provided with all products.)
One USB cable (Image may vary from

actual product. May not be provided
with all products.)
If any of these items are missing or damaged, please contact your service provider
for assistance.
Notes:
You need an optional cable signal splitter and additional standard RF coaxial
cables if you want to connect a VCR, a Digital Home Communications Terminal
(DHCT) or a set-top converter, or a TV to the same cable connection as your
residential gateway.
If your product supports telephone service, cables, and other equipment needed
for telephone service must be purchased separately. Contact your service
provider to inquire about the equipment and cables you need for telephone
service.
OL-29 159 -01
Front Panel Description

The front panel of your residential gateway provides LED status indicators that
indicate how well and at what state your residential gateway is operating. See
Operation of Front Panel Indicators (on page 17), for more information on front
panel LED status indicator functions.
POWERON, power is applied to the residential gateway.
DSON, the residential gateway is receiving data from the cable network.
USON, the residential gateway is sending data to the cable network.
ONLINEON, the residential gateway is registered on the network and fully

operational.
LINKON, the Ethernet connection is operational. BLINKING indicates that

data is being transferred over the Ethernet connection. OFF indicates that the
Ethernet connection is not connected or has been disabled by the user.
USBON, a device is connected to the USB port. BLINKING indicates that data
is being transferred over the USB connection.
WIRELESS ON/OFF (Optional)Press this button to activate and turn on the

Wireless feature. This feature allows users to transfer data over the wireless
connection. When the WIRELESS indicator is ON, it indicates that the Wireless
Access Point is operational. BLINKING indicates that data is being transferred
over the wireless connection. OFF indicates that the Wireless feature has been
disabled.
WIRELESS SETUPPress this button to activate the Wireless Setup feature.

This feature allows users to add new Wireless Protected Setup (WPS) compliant
wireless clients to the home network. When the SETUP indicator is OFF (normal
condition), it indicates that the wireless setup is not active. BLINKING indicates
the user has activated wireless setup to add new wireless clients on the wireless
network.
OL-29159-01
Back Panel Description
Back Panel Description

The following illustration identifies the back panel components on the DPC3828 and
EPC3828 residential gateways. Descriptions for each component follow the
illustration.
Important: Do not connect your PC to both the Ethernet and USB ports at the same
time. Your residential gateway will not function properly if both the Ethernet and
USB ports are connected to your PC at the same time.
1
ON/OFF SWITCH (Provided only on products that carry the CE mark)

Allows you to turn off the residential gateway without removing the power cord.
Turning the residential gateway off using this switch ensures that the unit is
consuming no energy.
POWERConnects the residential gateway to the AC power adapter that is

provided with your residential gateway.
Important: Use only the power supply provided with your residential gateway.
OL-29 159 -01
USB (Optional for some models)Connects to selected devices. For models that
support USB, the default is one USB port.
ETHERNETFour RJ-45 Ethernet ports connect to the Ethernet port on your PC

or your home network.
CABLEF-connector connects to an active cable signal from your service

provider.
RESETA momentary pressing (1-2 seconds) of this switch restarts (power

cycles) the device. Pressing and holding the switch for more than ten seconds
first causes a reset-to-factory-default of all settings and then restarts (power
cycles) the device.
5

CAUTION:
The RESET button is for maintenance purposes only. Do not use unless
instructed to do so by your service provider. Doing so may cause you to lose
any settings you have selected.
MAC ADDRESS LABELDisplays the CM and WAN MAC addresses for the
residential gateway
OL-29159-01
2 Chapter 2
Installing the DOCSIS Wireless
Residential Gateway
Introduction
This chapter describes how to properly install the residential gateway
and to connect the residential gateway to a computer and other
devices.
In This Chapter
OL-29 159 -01
Installation P reparations ......................................................................8

Install the Wireless Res idential Gateway .........................................13
Chapter 2 Installing the D OC SIS Wireless Residential Gateway
Installation Preparations
Before installing the residential gateway, make sure that your system meets or
exceeds the requirements listed in this section. Also, make sure that you have
prepared your home and home devices as described in this section.
What Are the System Requirements for Internet Service?

To ensure that your residential gateway operates efficiently for high-speed Internet
service, you must have an Internet-capable PC, Mac, or Internet appliance equipped
with an Ethernet port.
Note: You will also need an active cable input line and an Internet connection.
What Types of Service Accounts Do I Need?

Depending upon the features your service provider offers, you may need to establish
one or both of the following accounts:
A high-speed Internet access account, if your residential gateway supports an
Internet connection
An account for telephone service, if your residential gateway supports digital
telephone service
Refer to one of the following topics to learn more about the types of service accounts
that you may need to establish.
High-Speed Internet Access Account
If you do not have a high-speed Internet access account, your service provider will
set up your account and become your Internet Service Provider (ISP). Internet access
enables you to send and receive e-mail, access the World Wide Web, and receive
other Internet services.
You will need to give your service provider information about the residential
gateway in order to use the high-speed internet feature that this product offers. Refer
to Information Your Service Provider Needs (on page 9) to learn how to locate the
information your service provider needs to establish a high-speed Internet access
account for the residential gateway
If you have an existing high-speed Internet access account, you will need to give
your service provider the serial number and MAC address of the residential gateway
in order to use the high-speed internet feature that this product offers. Refer to
Information Your Service Provider Needs (on page 9) to learn how to locate this
information.
OL-29159-01
Information Your Serv ice Prov ider Needs

You will need to give your service provider the following information, which is
printed on the bar code label attached to the device:
The Serial Number (S/N) of the residential gateway. The serial number consists
of a series of nine digits.
The Media Access Control (CM MAC) address of the residential gateway. The
CM MAC address consists of a series of 12 alphanumeric characters.
The Media Access Control (MAC) address of the residential gateway media
terminal adapter (MTA MAC). The MTA MAC address consists of a series of 12
alphanumeric characters.
The following illustration shows a typical bar coded label; the image may vary from
the label on the actual product.
Write down these numbers in the spaces provided:

Serial Number _______________________
CM MAC MAC Address ________________________
MTA MAC Address ________________________

I Already Hav e a High-Speed Internet Access Account
Where Is the Best Location for My Wireless Residential Gateway?

The ideal location for your residential gateway is where it has access to outlets and
other devices. Think about the layout of your home or office, and consult with your
service provider to select the best location for your residential gateway. Read this
user guide thoroughly before you decide where to place your residential gateway.
Consider these recommendations:
Choose a location close to your computer if you will also use the residential
OL-29 159 -01
gateway for high-speed Internet service.

Choose a location that is near an existing RF coaxial connection to eliminate the
need for an additional RF coaxial outlet.
Choose a location that is relatively protected from accidental disturbance or
harm, such as a closet, basement, or other protected area.
Choose a location so that there is plenty of room to guide the cables away from
the residential gateway without straining or crimping them.
Choose a location that allows adequate ventilation around the residential
gateway.
How Do I Mount the Wireless Residential Gateway on a Wall? (Optional)

If you wish, you can mount the residential gateway to a wall. This section describes
how to mount the residential gateway to a wall, and includes a list of equipment you
will need along with suggestions for choosing an appropriate place to mount the
Select an Appropriate Place to Mount the Wireless Residential Gateway
You may mount the residential gateway to a wall that is made of cement, wood, or
drywall. When choosing an appropriate mounting place, refer to the following
recommendations:
Ensure that the mounting location is free of obstructions on all sides, and the
cables should be able to easily reach the residential gateway without strain.
Leave sufficient clearance between the bottom of the residential gateway and any
flooring or shelving underneath to allow access to cabling.
Allow enough slack in all cables so that the residential gateway can be removed
for any required maintenance without disconnecting the cables.
Choose a location that allows adequate ventilation around the residential
gateway.
Equipment Needed
Verify that you have the following items that you will need to mount the residential
gateway:
Two wall anchors for #8 x 1-inch screws
Two #8 x 1-inch pan head sheet metal screws
Drill with a 3/16-in. wood or masonry bit, as appropriate for the wall
composition
A copy of the wall-mounting illustrations shown on the following pages
10
OL-29159-01
Position the Wireless Residential Gateway

Use the following illustrations to guide you in positioning the residential gateway on
the wall.
Location and Dimensions of the Wall-Mounting Slots

The following illustration shows the location and dimensions of the wall-mounting
slots on the bottom of the residential gateway. Use this illustration as a guide for
mounting the residential gateway to the wall.
OL-29 159 -01
11
Note: Image not to scale.
Mounting the Wireless Residential Gateway on a Wall

1
Using a drill with a 3/16-inch bit, drill two holes at the same height and 4 inches
apart.
Note: The preceding graphic illustrates the location of the mounting holes on the
back of the residential gateway.
Are you mounting the residential gateway into a drywall or concrete surface
where a wooden stud is available?
If yes, go to step 3.
If no, drive the anchor bolts into the wall, and install the mounting screws
into the anchor bolts; leave a gap of about 1/4-inch between the screw head
and the wall. Then, go to step 4.
Install the mounting screws into the wall; leave a gap of about 1/4-inch between
the screw head and the wall. Then, go to step 4.
Verify that no cables or wires are connected to the residential gateway.
Lift the residential gateway into position. Slip the large end of both mounting
slots (located in the back of the residential gateway) over the mounting screws,
and then slide the residential gateway down until the narrow end of the keyhole
slot contacts the screw shaft.
Important: Verify that the mounting screws securely support the residential
gateway before you release the unit.
12
OL-29159-01
Install the Wireless Residential Gateway

This section describes how to connect your residential gateway to support the
services that the residential gateway offers.
Connect Devices to the Wireless Residential Gateway

The following illustration shows all of the possible connections that can be made to
your residential gateway for various services. Although your model may not
support all of the services pictured, you can determine which services your model
supports by referring to the Benefits and Features list in Introduction (on page 2).
Note: Professional installation may be available. Contact your local service provider
for further assistance.
Connect the Wireless Residential Gateway

The following installation procedure ensures proper setup and configuration for the
OL-29 159 -01
13
Choose an appropriate and safe location to install the residential gateway (close
to a power source, an active cable connection, and your PC-if using high-speed
Internet). For assistance, go to Where Is the Best Location for My Wireless
Residential Gateway? (on page 9).
WARNING:
To avoid personal injury, follow the installation instructions in the exact

order shown.
Wiring and connections must be properly insulated to prevent electrical

shock.
Disconnect power from the residential gateway before attempting to

connect to any device.
Power off your PC and other networking device; then, unplug them from the
power source.
Connect the active RF coaxial cable from your service provider to the coax
connector labeled CABLE on the back of the residential gateway.
Note: To connect a TV, DHCT, set-top, or VCR from the same cable connection,
you will need to install a cable signal splitter (not included). Always check with
your service provider before using a splitter as a splitter may degrade the signal.
Connect your PC to the residential gateway using either of the following

connections:
Ethernet Connection: Locate the yellow Ethernet cable, connect one end of
the Ethernet cable to the Ethernet port on your PC, and connect the other end
to the yellow ETHERNET port on the back of the residential gateway.
Note: To install more Ethernet devices than ports provided on the residential
gateway, use an external mulit-port Ethernet switch(s).
Wireless: Make sure that your wireless device is powered up. You will need
to associate your wireless device with the wireless residential gateway once
the residential gateway is operational. Follow the directions provided for
your wireless device for associating with a wireless access point. If the
residential gateway has a WIRELESS ON/OFF button, make sure that
WIRELESS is enabled by confirming that the ON/OFF indicator is ON. If the
indicator is OFF, press the ON/OFF button to enable the WIRELESS feature.
More information about the factory default configuration of your wireless
residential gateway can be found later in this guide in Configure Wireless
Settings.
14
Locate the AC power cord provided with your residential gateway. Insert one
end of the power cord into the AC connector on the back of the residential
gateway. Then, plug the AC power cord into an AC outlet to power-up the
residential gateway. The residential gateway will perform an automatic search to
locate and sign on to the broadband data network. This process may take up to 25 minutes. The residential gateway will be ready for use when the POWER, DS,
US, and ONLINE LEDs on the front panel of the residential gateway stop
blinking and remain on continuously.
OL-29159-01
Plug in and power on your PC and other home network devices. The LINK LED
on the residential gateway corresponding to the connected devices should be on
or blinking.
Once your residential gateway is online, most Internet devices will have
immediate Internet access.
Note: If your PC does not have Internet access, refer to How Can I Make Sure
TCP/IP Is Configured Correctly on my PC? (see "How Do I Configure TCP/IP
Protocol?" on page 24) for information on how to configure your PC for TCP/IP.
For Internet devices other than PCs, refer to the DHCP or IP Address
configuration section of the User Guide or Operations Manual for those devices.
OL-29 159 -01
15
3 Chapter 3
Operation of Front Panel
Indicators
Introduction
This section describes the behavior of the front panel indicators when
the residential gateway is first powered up, during normal operations,
and in special conditions.
In This Chapter
OL-29 159 -01
Initial Power Up, Calibration, and Registration (AC Power

Applied) ..............................................................................................18
Normal Op erations (AC Power Applied) ........................................20
Special Conditions ..............................................................................21
17
Initial Power Up, Calibration, and Registration (AC

Power Applied)
The following chart illustrates the sequence of steps and the corresponding
appearance of the residential gateway front panel LED status indicators during
power up, calibration, and registration on the network when AC power is applied to
the residential gateway. Use this chart to troubleshoot the power up, calibration, and
registration process of your residential gateway.
Note: After the residential gateway completes Step 7 (Data Network Registration
Complete), the residential gateway proceeds immediately to Normal Operations. See
Normal Operations (AC Power Applied) (on page 20).
Front Panel LED Status Indicators During Initial Pow er Up, Calibration, and
Registration
Part 1, High Speed Data Registration
Step:
Front Panel
Indicator
Self
Test
Downstream
Scan
Downstream
Signal Lock
Ranging
Requesting IP
Address
Request High Speed

Data Provisioning
File
POWER
On
On
On
On
On
On
DS
On
Blinking
On
On
On
On
US
On
Off
Off
Blinking
On
On
ONLINE
On
Off
Off
Off
Off
Blinking
LINK
On
Off, On, or
Blinking
Off, On, or
Blinking
Off, On, or Off, On, or

Blinking
Blinking
Off, On, or Blinking
USB
On
Off, On, or
Blinking
On or Blinking
On or
Blinking
On or Blinking
On or Blinking
WIRELESS
ON/OFF
Off
On or Blinking
On or Blinking
On or
Blinking
On or Blinking
On or Blinking
WIRELESS
SETUP
Off
On or Blinking
On or Blinking
On or
Blinking
On or Blinking
On or Blinking
Front Panel LED Status

Indicators During Initial Pow er
Up, Calibration, and
Registration
High Speed Data Registration
(continued)
18
Step:
Front Panel
Indicator
Data Network
Registration
Complete
POWER
On
DS
On
US
On
4
5
ONLINE
LINK
On
On
OL-29159-01
Initial Power Up, Calibration, and Registration (AC Power Applied)
OL-29 159 -01
USB
On or Blinking
WIRELESS
ON/OFF
On or Blinking
WIRELESS
SETUP
Off
19
Normal Operations (AC Power Applied)

The following chart illustrates the appearance of the residential gateway front panel
LED status indicators during normal operations when AC power is applied to the
gateway.
Front Panel LED Status Indicators During Normal Conditions
Front Panel Indicator
Normal Operations
POWER
On
DS
On
US
On
ONLINE
On
LINK
On - When a single device is connected to the Ethernet

port and no data is being sent to or from the residential
gateway
Blinks - When only one Ethernet device is connected and

data is being transferred between the consumer premise
equipment (CPE) and the wireless home gateway
Off - When no devices are connected to the Ethernet ports
Blinks - When only one USB device is connected and data

is being transferred between the consumer premise
equipment (CPE) and the wireless home gateway
Off - When no devices are connected to the USB ports
Blinks - When data is being transferred between the CPE

and the wireless home gateway
Off - When the wireless access point is disabled by the

user
Off - When wireless setup is not active
USB
WIRELESS
ON/OFF
WIRELESS
SETUP
On - When a single device is connected to the USB port

and no data is being sent to or from the modem
On - When the wireless access point is enabled and

operational
Blinks - When wireless setup is active to add new wireless

clients on the wireless network
Note: In addition to the status shown in the previous table, some service providers
use color-coded LEDs to indicate detailed channel bonding and data link status. For
additional information about color-coded LEDs, check with your service provider.
20
OL-29159-01
Special Conditions
Special Conditions
The following chart describes the appearance of the residential gateway front panel
LED status indicators during special conditions to show when you have been denied
network access.
Front Panel LED Status Indicators During Special Conditions
Front Panel Indicator
POWER
Network Access Denied
Slow Blinking
(once per second)
DS
Slow Blinking
(once per second)
US
Slow Blinking
(once per second)
ONLINE
Slow Blinking
(once per second)
LINK
Slow Blinking
(once per second)
USB
Slow Blinking
(once per second)
OL-29 159 -01
WIRELESS
ON/OFF
WIRELESS
SETUP
Slow Blinking
(once per second)
Slow Blinking
(once per second)
21
4 Chapter 4
Troubleshooting the DOCSIS
Introduction
This chapter describes the most common issues that may occur after
the residential gateway is installed and provides possible solutions
and tips for improved performance of the residential gateway.
In This Chapter
OL-29 159 -01
Frequently Asked Questions .............................................................24

Common Troubles hooting Issues .....................................................29
Tips for Improved Performa nce ........................................................30
23
Chapter 4 Troubleshooting the D OCSIS Wireless Residential Gateway
Frequently Asked Questions

This section provides answers to common questions about the residential gateway.
How Do I Configure TCP/IP Protocol?

To configure TCP/IP protocol, you need to have an Ethernet Network Interface Card
(NIC) with TCP/IP communications protocol installed on your system. TCP/IP is a
communications protocol used to access the Internet. This section contains
instructions for configuring TCP/IP on your Internet devices to operate with the
residential gateway in Microsoft Windows or Macintosh environments.
TCP/IP protocol in a Microsoft Windows environment is different for each
operating system. Follow the appropriate instructions in this section for your
operating system.
Configuring TCP/IP on Window s 7 Sy stems
1 Open Network Connections by clicking the Start button, and then clicking
Control Panel.
2
In the Search box, type adapter, and then, under Network and Sharing Center,
click View network connections.
Right-click the connection that you want to change, and then click Properties. If
you are prompted for an administrator password or confirmation, type the
password or provide confirmation. The Local Area Connection Properties
window opens.
Click the Networking tab.
Under This connection uses the following items, click either Internet Protocol
Version 4 (TCP/IPv4) or Internet Protocol Version 6 (TCP/IPv6), and then click
Properties.
To specify IPv4 IP address settings, do one of the following:
8
24
To get IP settings automatically using DHCP, click Obtain an IP address

automatically, and then click OK.
To specify an IP address, click Use the following IP address, and then, in the
IP address, Subnet mask, and Default gateway boxes, type the IP address
settings.
To specify IPv6 IP address settings, do one of the following:
To get IP settings automatically using DHCP, click Obtain an IPv6 address

automatically, and then click OK.
To specify an IP address, click Use the following IPv6 address, and then, in
the IPv6 address, Subnet prefix length, and the Default gateway boxes, type
the IP address settings.
To specify DNS server address settings, do one of the following:

OL-29159-01
To get a DNS server address automatically using DHCP, click Obtain DNS
server address automatically, and then click OK.
To specify a DNS server address, click Use the following DNS server
addresses, and then, in the Preferred DNS server and Alternate DNS server
boxes, type the addresses of the primary and secondary DNS servers.
To change advanced DNS, WINS, and IP settings, click Advanced.
10 When you are finished, click OK.

11 Try to access the Internet. If you cannot access the Internet, contact your service
provider for further assistance.
Configuring TCP/IP on Window s XP Sy stems
1 Click Start, and depending on your Start menu setup, choose one of the
following options:
If you are using the Windows XP Default Start Menu, select Connect to,
choose Show all connections, and then go to step 2.
If you are using the Windows XP Classic Start Menu, select Settings, choose
Network Connections, click Local Area Connection, and then go to step 3.
Double-click the Local Area Connection icon in the LAN or High-Speed Internet
section of the Network Connections window.
Click Properties in the Local Area Connection Status window.
Click Internet Protocol (TCP/IP), and then click Properties in the Local Area
Connection Properties window.
Select both Obtain an IP address automatically and Obtain DNS server address
automatically in the Internet Protocol (TCP/IP) Properties window, and then
click OK.
Click Yes to restart your computer when the Local Network window opens. The
computer restarts. The TCP/IP protocol is now configured on your PC, and your
Ethernet devices are ready for use.
Try to access the Internet. If you cannot access the Internet, contact your service
provider for further assistance.
Configuring TCP/IP on Macintosh Sy stems

1 Click the Apple icon in the upper-left corner of the Finder. Scroll down to
Control Panels, and then click TCP/IP.
OL-29 159 -01
Click Edit on the Finder at the top of the screen. Scroll down to the bottom of the
menu, and then click User Mode.
Click Advanced in the User Mode window, and then click OK.
Click the Up/Down selector arrows located to the right of the Connect Via
section of the TCP/IP window, and then click Using DHCP Server.
Click Options in the TCP/IP window, and then click Active in the TCP/IP
Options window.
25
Note: Make sure that the Load only when needed option is unchecked.
6
Verify that the Use 802.3 option located in the upper-right corner of the TCP/IP
window is unchecked. If there is a check mark in the option, uncheck the option,
and then click Info in the lower-left corner.
Is there a Hardware Address listed in this window?
If yes, click OK. To close the TCP/IP Control Panel window, click File, and
then scroll down to click Close. You have completed this procedure.
If no, you must power off your Macintosh.
With the power off, simultaneously press and hold down the Command
(Apple), Option, P, and R keys on your keyboard. Keeping those keys pressed
down, power on your Macintosh but do not release these keys until you hear the
Apple chime at least three times, then release the keys and let the computer
restart.
When your computer fully reboots, repeat steps 1 through 7 to verify that all
TCP/IP settings are correct. If your computer still does not have a Hardware
Address, contact your authorized Apple dealer or Apple technical support center
for further assistance.
How Do I Renew the IP Address on My PC?

If your PC cannot access the Internet after the residential gateway is online, it is
possible that your PC did not renew its IP address. Follow the appropriate
instructions in this section for your operating system to renew the IP address on
your PC.
Renew ing the IP Address on Window s 7 Sy stems
1 Click the Windows Start button.
2
Type cmd in the Search box. The cmd window opens.
Type ipconfig /renew and press Enter to renew the IP address of the computer.
Renew ing the IP Address on Window s XP Sy stems

1 Click Start, and then click Run. The Run window opens.
2
Type cmd in the Open field and click OK. A window with a command prompt
opens.
Type ipconfig /release at the C:/ prompt and press Enter. The system releases
the IP address.
Type ipconfig /renew at the C:/ prompt and press Enter. The system displays a
new IP address.
Click the X in the upper-right corner of the window to close the Command
Prompt window. You have completed this procedure.
Note: If you cannot access the Internet, contact your service provider for further
assistance.
26
OL-29159-01
Renew ing the IP Address on Macintosh Sy stems

1
Close all open programs.
Open your Preferences folder.
Drag the tcp/ip preferences file to the Trash.
Close all open windows and empty the Trash.
Restart your computer.
As your computer starts, simultaneously press and hold down the Command
(Apple), Option, P, and R keys on your keyboard. Keeping those keys pressed
down, power on your Macintosh but do not release these keys until you hear the
Apple chime at least three times; then, release the keys and let the computer
restart.
When your computer fully reboots, click the Apple icon in the upper-left corner
of the Finder. Scroll down to Control Panels, and then click TCP/IP.
Click Edit on the Finder at the top of the screen. Scroll down to the bottom of the
menu, and then click User Mode.
Click Advanced in the User Mode window, and then click OK.
10 Click the Up/Down selector arrows located to the right of the Connect Via
section of the TCP/IP window, and then click Using DHCP Server.
11 Click Options in the TCP/IP window, and then click Active in the TCP/IP
Options window.
Note: In some cases, the Load only when needed option does not appear. If it
appears, select the option. A check mark appears in the option.
12 Verify that the Use 802.3 option located in the upper-right corner of the TCP/IP
window is not selected. If there is a check mark in the option, select the option to
clear the check mark, and then click Info in the lower-left corner.
13 Is there a Hardware Address listed in this window?
If yes, click OK. To close the TCP/IP Control Panel window, click File, and
then scroll down to click Close.
If no, repeat these instructions from step 6.
14 Reboot your computer.
What if I Don't Subscribe to Cable TV?

If cable TV is available in your area, data service may be made available with or
without subscribing to cable TV service. Contact your local service provider for
complete information on cable services, including high-speed Internet access.
OL-29 159 -01
27
How Do I Arrange for Installation?

Call your service provider to inquire about professional installation. A professional
installation ensures proper cable connection to the residential gateway and to your
PC, and it ensures the proper configuration of all hardware and software settings.
Contact your service provider for more information about installation.
How Does the Wireless Residential Gateway Connect to My Computer?

The residential gateway connects to the 10/100/1000BASE-T Ethernet port on your
PC. To use the Ethernet interface, Ethernet cards available from your local PC or
office supply retailer, or from your service provider. For best performance over an
Ethernet connection, your PC should be equipped with a Gigabit Ethernet card.
After My Wireless Residential Gateway Is Connected, How Do I Access the

Internet?
Your local service provider becomes your Internet Service Provider (ISP). They offer
a wide range of services including e-mail, chat, news, and information services. Your
service provider will provide the software you will need.
Can I Watch TV and Surf the Internet at the Same Time?

Absolutely! If you subscribe to cable television service, you can watch TV and use
your residential gateway at the same time by connecting your TV and your
residential gateway to the cable network using an optional cable signal splitter.
28
OL-29159-01
Common Troubleshooting Issues
Common Troubleshooting Issues

This section describes common problems and offers solutions.
I don't understand the front panel status indicators

See Operation of Front Panel Indicators (on page 17), for more detailed information
on front panel LED status indicator operation and function.
The Wireless Residential Gateway does not register an Ethernet connection

Try one of the following solutions:
Verify that your computer has an Ethernet card and that the Ethernet driver
software is properly installed. If you purchase and install an Ethernet card,
follow the installation instructions very carefully.
Verify the status of the front panel status indicator lights.
The Wireless Residential Gateway does not register an Ethernet connection after
connecting to a hub
If you are connecting multiple PCs to the residential gateway, you should first
connect the residential gateway to the uplink port of the hub using the correct
crossover cable. The LINK LED of the hub will illuminate continuously.
The Wireless Residential Gateway does not register a cable connection

The residential gateway works with a standard, 75-ohm, RF coaxial cable. If you are
using a different cable, your residential gateway will not function properly. Contact
your service provider to determine whether you are using the correct cable.
OL-29 159 -01
29
Tips for Improved Performance

If your residential gateway does not perform as expected, the following tips may
help. If you need further assistance, contact your service provider.
Verify that the plug to your residential gateway AC power is properly inserted
into an electrical outlet.
Verify that your residential gateway AC power cord is not plugged into an
electrical outlet that is controlled by a wall switch. If a wall switch controls the
electrical outlet, make sure the switch is in the ON position.
Verify that the ONLINE LED status indicator on the front panel of your
residential gateway is illuminated.
Verify that your cable service is active and that it supports two-way service.
Verify that all cables are properly connected, and that you are using the correct
cables.
If you are using the Ethernet connection, verify that your TCP/IP is properly
installed and configured.
Verify that you have called your service provider and given them the serial
number and MAC address of your residential gateway.
If you are using a cable signal splitter so that you can connect the residential
gateway to other devices, remove the splitter and reconnect the cables so that the
residential gateway is connected directly to the cable input. If the residential
gateway now functions properly, the cable signal splitter may be defective and
may need to be replaced.
If you are connected to your PC with an Ethernet connection, your PC should be
equipped with a Gigabit Ethernet card for best performance.
30
OL-29159-01
5 Chapter 5
Customer Information
Introduction
If you have technical questions, call Cisco Services for assistance.
Follow the menu options to speak with a service engineer.
Access your company's extranet site to view or order additional
technical publications. For accessing instructions, contact the
representative who handles your account. Check your extranet site
often as the information is updated frequently.
OL-29 159 -01
31
Index
power switch 5
product 2
A
accessing the Internet 28
accessories 3
performance, tips to improve 30

product
accessories 3
features 2
overview 2
cable service 27
connections
description of 5
how to connect 13
to computer 28
E
Ethernet 29
exposure to moisture viii
F
features, product 3
I
indicators
behavior 18, 20, 21
described 4
operation of 17
installation
professional 28
installation requirements
minimum system requirements 8
ventilation viii
Internet
how to access 28
surfing while watching T V 28
unable to access 26
IP address, renewing 27
S
safety instructions vii
ground product vii
system requirements 8
T
T CP/IP
configuring for Macintosh systems 25
configuring for Windows XP 25
troubleshooting 23
U
unpacking 3
USB 3, 28
V
ventilation requirements viii
Voice settings
LEDs 4, 18, 20, 21
W
wall mounting
instructions 12
slots 11
L
LEDs 4, 18, 20, 21
location
selecting viii, 9
O
overview
OL-29 159 -01
33
Cisco Systems, Inc.

5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
678 277-1120
800 553-6387
www.cisco.com
This document includes various trademarks of Cisco Systems, Inc. Please see the Notices
section of this document for a list of the Cisco Systems, Inc. trademarks used in this
document.
Product and service availability are subject to change without notice.
2013 Cisco and/or its affiliates. All rights reserved.
April 2013 Printed in USA
Part Number OL-29159-01

Cisco Dpc3828

Uploaded by

Copyright:

Available Formats

Cisco Dpc3828

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cisco Dpc3828

Uploaded by

Copyright:

Available Formats

O

Cisco Model DPC3828/EPC3828

Software and Firmware Use

United States FCC Compliance

Chapter 1 Introducing the DOCSIS Wireless Residential Gateway 1

Chapter 2 Installing the DOCSIS Wireless Residential Gateway

Installation P reparations ..................................................................................................... 8

Chapter 3 Operation of Front Panel Indicators

Initial Power Up, Calibration, and Registration (AC Power Applied).......................... 18

Chapter 4 Troubleshooting the DOCSIS Wireless Residential

Frequently Asked Questions ............................................................................................ 24

OL-29 159 -01

Chapter 5 Customer Information

Notice lattention des installateurs de rseaux cbls

Aviso a los instaladores de sistemas CATV

2 0 0 8 0 8 1 4 _Insta ller8 2 0 _ Intl

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not defeat the safety purpose of the polarized or grounding-type plug. A

Only use attachments/accessories specified by the manufacturer.

Power Source Warning

IMPORTANT SAFETY INSTRUCTIONS

Ground the Product

Protect the Product from Lightning

Verify the Power Source from the On/Off Power Light

Eliminate AC Power/Mains Overloads

Provide Ventilation and Select a Location

Do not block ventilation openings.

IMPORTANT SAFETY INSTRUCTIONS

Protect from Exposure to Moisture and Foreign Objects

Check Product Safety

Protect the Product When Moving It

OL-29 159 -01

United States FCC Compliance

United States FCC Compliance

Reorient or relocate the receiving antenna.

Consult the service provider or an experienced radio/television technician for help.

Increase the separation between the equipment and receiver.

DOCSIS Wireless Residential Gateway

Canada EMI Regulation

United States FCC Compliance

OL-29 159 -01

Radio: EN 300 328

OL-29 159 -01

OL-29 159 -01

Chapter 1 Introducing the DOC SIS Wireless Residential Gateway

What's In the Carton?

What's In the Carton?

One DPC3828 or EPC3828 DOCSIS

One Ethernet cable (May not be

One USB cable (Image may vary from

OL-29 159 -01

Chapter 1 Introducing the DOC SIS Wireless Residential Gateway

Front Panel Description