RINA - Inclining Test & Lightweight Check

Pt B, Ch 3, App 1
APPENDIX 1
1
1.1
INCLINING TEST AND LIGHTWEIGHT CHECK
Inclining test and lightweight check

General
1.1.1 General conditions of the ship

Prior to the test, the Societys Surveyor is to be satisfied of
the following:
the weather conditions are to be favourable
the ship is to be moored in a quiet, sheltered area free
from extraneous forces, such as to allow unrestricted
heeling. The ship is to be positioned in order to minimise the effects of possible wind, stream and tide
the ship is to be transversely upright and the trim is to be
taken not more than 1% of the length between perpendiculars. Otherwise, hydrostatic data and sounding
tables are to be available for the actual trim
cranes, derrick, lifeboats and liferafts capable of inducing oscillations are to be secured
main and auxiliary boilers, pipes and any other system
containing liquids are to be filled
the bilge and the decks are to be thoroughly dried
preferably, all tanks are to be empty and clean, or completely full. The number of tanks containing liquids is to
be reduced to a minimum taking into account the
above-mentioned trim. The shape of the tank is to be
such that the free surface effect can be accurately determined and remain almost constant during the test. All
cross connections are to be closed
the weights necessary for the inclination are to be
already on board, located in the correct place
all work on board is to be suspended and crew or personnel not directly involved in the inclining test are to
leave the ship
the ship is to be as complete as possible at the time of
the test. The number of weights to be removed, added
or shifted is to be limited to a minimum. Temporary
material, tool boxes, staging, sand, debris, etc., on
board is to be reduced to an absolute minimum.
1.1.2 Inclining weights
The total weight used is preferably to be sufficient to provide a minimum inclination of one degree and a maximum
of four degrees of heel to each side. The Society may, however, accept a smaller inclination angle for large ships provided that the requirement on pendulum deflection or Utube difference in height specified in [1.1.4] is complied
with. Test weights are to be compact and of such a configuration that the VCG (vertical centre of gravity) of the
weights can be accurately determined. Each weight is to be
marked with an identification number and its weight. Recertification of the test weights is to be carried out prior to
the incline. A crane of sufficient capacity and reach, or
some other means, is to be available during the inclining test
RINA Rules 2009
to shift weights on the deck in an expeditious and safe manner. Water ballast is generally not acceptable as inclining
weight.
1.1.3 Water ballast as inclining weight
Where the use of solid weights to produce the inclining
moment is demonstrated to be impracticable, the movement of ballast water may be permitted as an alternative
method. This acceptance would be granted for a specific
test only, and approval of the test procedure by the Society
is required. As a minimal prerequisite for acceptability, the
following conditions are to be required:
inclining tanks are to be wall-sided and free of large

stringers or other internal members that create air pockets
tanks are to be directly opposite to maintain ships trim
specific gravity of ballast water is to be measured and

recorded
pipelines to inclining tanks are to be full. If the ships

piping layout is unsuitable for internal transfer, portable
pumps and pipes/hoses may be used
blanks must be inserted in transverse manifolds to prevent the possibility of liquids being leaked during
transfer. Continuous valve control must be maintained
during the test
all inclining tanks must be manually sounded before and

after each shift
vertical, longitudinal and transverse centres are to be

calculated for each movement
accurate sounding/ullage tables are to be provided. The

ships initial heel angle is to be established prior to the
incline in order to produce accurate values for volumes
and transverse and vertical centres of gravity for the
inclining tanks at every angle of heel. The draught marks
amidships (port and starboard) are to be used when
establishing the initial heel angle
verification of the quantity shifted may be achieved by a

flowmeter or similar device
the time to conduct the inclining is to be evaluated. If

time requirements for transfer of liquids are considered
too long, water may be unacceptable because of the
possibility of wind shifts over long periods of time.
1.1.4 Pendulums
The use of three pendulums is recommended but a minimum of two are to be used to allow identification of bad
readings at any one pendulum station. However, for ships of
a length equal to or less than 30 m, only one pendulum can
be accepted. They are each to be located in an area protected from the wind. The pendulums are to be long
enough to give a measured deflection, to each side of
upright, of at least 10 cm. To ensure recordings from indi-
57
Pt B, Ch 3, App 1
vidual instruments are kept separate, it is suggested that the

pendulums be physically located as far apart as practical.
The use of an inclinometer or U-tube is to be considered in
each separate case. It is recommended that inclinometers or
other measuring devices only be used in conjunction with at
least one pendulum.
measured when the sample temperature differs from the

temperature at the time of the inclining (e.g., if the
check of specific gravity is performed at the office).
Where the value of the average calculated specific gravity is different from that reported in the hydrostatic
curves, adequate corrections are to be made to the displacement curve
1.1.5 Means of communications

Efficient two-way communications are to be provided
between central control and the weight handlers and
between central control and each pendulum station. One
person at a central control station is to have complete control over all personnel involved in the test.
all double bottoms, as well as all tanks and compartments which can contain liquids, are to be checked,
paying particular attention to air pockets which may
accumulate due to the ships trim and the position of air
pipes, and also taking into account the provisions of
[1.1.1]
1.1.6 Documentation
The person in charge of the inclining test is to have available
a copy of the following plans at the time of the test:
hydrostatic curves or hydrostatic data
general arrangement plan of decks, holds, inner bottoms, etc
capacity plan showing capacities and vertical and longitudinal centres of gravity of cargo spaces, tanks, etc.
When water ballast is used as inclining weights, the
transverse and vertical centres of gravity for the applicable tanks, for each angle of inclination, must be available
tank sounding tables
draught mark locations, and
docking drawing with keel profile and draught mark corrections (if available).
1.1.7 Determination of the displacement
The Societys Surveyor is to carry out all the operations necessary for the accurate evaluation of the displacement of the
ship at the time of the inclining test, as listed below:
draught mark readings are to be taken at aft, midship
and forward, at starboard and port sides
the mean draught (average of port and starboard reading) is to be calculated for each of the locations where
draught readings are taken and plotted on the ship's
lines drawing or outboard profile to ensure that all readings are consistent and together define the correct
waterline. The resulting plot is to yield either a straight
line or a waterline which is either hogged or sagged. If
inconsistent readings are obtained, the freeboards/draughts are to be retaken
the specific gravity of the sea water is to be determined.
Samples are to be taken from a sufficient depth of the
water to ensure a true representation of the sea water
and not merely surface water, which could contain fresh
water from run off of rain. A hydrometer is to be placed
in a water sample and the specific gravity read and
recorded. For large ships, it is recommended that samples of the sea water be taken forward, midship and aft,
and the readings averaged. For small ships, one sample
taken from midship is sufficient. The temperature of the
water is to be taken and the measured specific gravity
corrected for deviation from the standard, if necessary.
A correction to water specific gravity is not necessary if
the specific gravity is determined at the inclining experiment site. Correction is necessary if specific gravity is
58
it is to be checked that the bilge is dry, and an evaluation of the liquids which cannot be pumped, remaining
in the pipes, boilers, condenser, etc., is to be carried out
the entire ship is to be surveyed in order to identify all
items which need to be added, removed or relocated to
bring the ship to the lightship condition. Each item is to
be clearly identified by weight and location of the centre of gravity
the possible solid permanent ballast is to be clearly
identified and listed in the report.
1.1.8
The incline
The standard test generally employs eight distinct weight

movements as shown in Fig 1.
Figure 1 : Weight shift procedure
Inertial position
1
2
3
4
1 shift
2 shift
3 shift
4 shift
4
5 shift
6 shift
4
7 shift
8 shift
3
4
2
3
4
The weights are to be transversally shifted, so as not to modify the ships trim and vertical position of the centre of gravity.
After each weight shifting, the new position of the transverse centre of gravity of the weights is to be accurately
determined.
RINA Rules 2009
Pt B, Ch 3, App 1
After each weight movement, the distance the weight was

moved (centre to centre) is to be measured and the heeling
moment calculated by multiplying the distance by the
amount of weight moved. The tangent is calculated for each
pendulum by dividing the deflection by the length of the
pendulum. The resultant tangents are plotted on the graph
as shown in Fig 2.
Figure 2 : Graph of resultant tangents
heeling angles
tangential (starboard)
heeling moment (port)
The pendulum deflection is to be read when the ship has

reached a final position after each weight shifting.
heeling moment
(starboard)
During the reading, no movements of personnel are

allowed.
For ships with a length equal to or less than 30 m, six distinct weight movements may be accepted.
RINA Rules 2009
heeling angles
tangential (port)
59

RINA - Inclining Test & Lightweight Check

Uploaded by

Copyright:

Available Formats

RINA - Inclining Test & Lightweight Check

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RINA - Inclining Test & Lightweight Check

Uploaded by

Copyright:

Available Formats

Pt B, Ch 3, App 1

INCLINING TEST AND LIGHTWEIGHT CHECK

Inclining test and lightweight check

1.1.1 General conditions of the ship

RINA Rules 2009

inclining tanks are to be wall-sided and free of large

tanks are to be directly opposite to maintain ships trim

specific gravity of ballast water is to be measured and

pipelines to inclining tanks are to be full. If the ships

all inclining tanks must be manually sounded before and

vertical, longitudinal and transverse centres are to be

accurate sounding/ullage tables are to be provided. The

verification of the quantity shifted may be achieved by a

the time to conduct the inclining is to be evaluated. If

vidual instruments are kept separate, it is suggested that the

measured when the sample temperature differs from the

1.1.5 Means of communications

The standard test generally employs eight distinct weight

RINA Rules 2009

After each weight movement, the distance the weight was

Figure 2 : Graph of resultant tangents

heeling moment (port)

The pendulum deflection is to be read when the ship has

During the reading, no movements of personnel are

RINA Rules 2009

You might also like