Tyre Report Sample

PARAMETERS INFLUENCING TYRE MODELLING FOR SUSPENSION DESIGN
Saurabh Ranjan Sharma, AUE, For Student Formula Competetion 2015
ABSTRACT
The purpose of this document is to describe important tyre characteristics and their effects on vehicle
performance. The said vehicle to be designed and manufactured for SUPRA SAE India, Students Formula
2015. The characteristics considered are those that the judges have deemed important for discussion on
tyres at the competition and have actually proved to be crucial for precise design of an automobile
suspension.
INTRODUCTION
Importance of a tyre in a racing competition cannot be overemphasized given that it is the only means
of contact between the road and the vehicle. The tyres are required to produce the forces necessary to
control the vehicle. It will be safe to say that they are at the heart of vehicle handling and performance.
Insight into the various tyre parameters will help us students in many ways. Knowledge of these
characteristics and their effects on racecar performance can give the engineer insight into performance
optimization. A firm grasp on what influences a tyres behavior and how it affects the overall vehicle
dynamics will better prepare the students to score higher during design judging competition. However,
tyre itself is very complex. What we can do is study the specific tyre characteristics in relation with the
racecar dynamics for which purpose we are designing the prototype in the first place.
The Parameters required for the design are:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Co-efficient of friction
Vertical stiffness
Slip angle
Slip ratio
Camber angle
Cornering stiffness
Camber stiffness
Self-aligning torque
Pneumatic trail
Effective rolling radius
Current condition of the tyre in use from the previous vehicle.
SAE CO-ORDINATE SYSTEM
TIRE MODEL ADOPTED

Tyres are complex composites containing many layers of different materials, anisotropic. Hence its
material properties and structure cannot be used to derive its behavior. Simpler empirical models of the
tyre has been adopted to derive its behavior. Though no model truly addresses the complexity of a real
world tyre, realistic results can be obtained when empirical stiffness values are used. The simplest of the
models is the elastic foundation model (Ref: 1).
Each element in an elastic foundation model is considered to be an independent spring. This
model allows for discontinuity in the displacement distribution and slope of center line.
CO-EFFICIENT OF FRICTION
-
Defined as the unit-less ratio of friction force to normal force, not proportional to surface area
of contact.
In case of tyres, this is wrong. Because of viscoelastic behavior of rubber, deformation occurs in tyre,
both elastic and plastic in a non-linear fashion due to natural property of polymer chains.
As the tyre is loaded, total frictional force increases with surface area but co-efficient of friction
is reduced. Hence, coefficient of friction of a tyre can be greater than 1. It can depend upon many
factors: atmospheric dust, humidity, temperature, vibration and extent of contamination.
As the temperature rises due to some reason (continuous skidding/high speeds), the coefficient of
friction attains highest value in the optimal temperature range then starts decreasing. When slip angle
becomes large, the rear of the patch begins to slide and attains low coefficient of friction.
Availability of coefficient of friction facilitates Modelling of Braking system and is required for the
further calculations.
VERTICAL TYRE STIFNESS

The tyre acts as a spring, a part of the suspension system when in contact with the road and hence plays
an important part in the overall suspension design.
Thus as any conventional spring, the tyres have a stiffness/rate.
F = Kt*x
Kt = F/x
N/m
This rate is related to the overall ride rate of a vehicle by:

1/Kr = 1/Kw + 1/Kt
SLIP ANGLE ()
-
Defined as the angle between the wheels direction of travel and wheel heading.
The slip angle produces a component of lateral force (FY). This lateral force acts from behind the center
line of the wheel in a direction that it attempts to realign the tyre. Evident from elastic foundation
model, there is a friction limited value of the lateral force due to the slip angle.
c.d (.FV) / l
c: foundation stiffness
d: tyre center line displacement
l: tyre footprint length
Maximum non-slide force, FY = 0.5*c*l2*

0.5*c*d*l = 0.5*c*{(.FV) / l*c}*l = 0.5* .FV
At high slip angles, rear of the footprint slides on the road surface: Lesser capacity for lateral force,
reduction of self-aligning torque.
When not completely sliding, lateral force is independent of coefficient of friction, depends on
foundation stiffness.
FY = F = C* = CS*FV*
[C = CS*FV]
CS: Cornering stiffness coefficient

C: Cornering stiffness
Since central/drag force ratio reduces with slip angle, higher cornering stiffness is desirable
Ref. Fig:
cos
+sin
SLIP RATIO (% SLIP)

-
Slip in longitudinal plane
SR = (-)/ = {*Re/V*cos } 1
: Angular velocity of driven wheel

: Angular velocity of free rolling wheel
Re: Effective rolling radius
V: Velocity
CAMBER ANGLE
FV = F = C* = Cc*FV*
: Camber angle
C: Camber stiffness
Cc: Camber stiffness coefficient
Camber stiffness is rate of change of camber force with camber angle (F/)
TOTAL LATERAL FORCE

FY = F + F = C* + C*
FY = FV*(CS + CC)
SELF ALIGNING TORQUE
-
Resultant of lateral force and pneumatic trail
Trail may also be induced mechanically from suspension geometry with presence of castor and kingpin
offset.
MZ = FY*t = FY.l/6 = (c*l2*tan )/12
MZ = {2*FV2/ (4*c*l tan )} {(3* FV3)/(6*c2*l3*tan2)}
As slip angle increases, lateral force increases, self-aligning torque decreases. This means that as the
slip angle decreases and lateral force begins to reach its limit, the driver loses the feedback through the
tyres. However this loss of feedback alerts him of the slide beforehand.
Self-aligning torque also affected by tyre pressure.
PNEUMATIC TRAIL
-
Moment arm through which lateral force acts.
As per foundation stiffness model, the lateral force acts from behind the wheels center line.
Now, considering the contact patch as near triangular distribution,
t = MZ/FY=l/6
EFFECTIVE ROLLING RADIUS

Front and rear tyre loaded radius is required to calculate the CG location of non-suspended mass.
REFERENCES
1. Dixon, J.C. (1996). Tires, Suspension and Handling.
2. Smith, Nicholas D. (2004). Understanding parameters influencing Tire Modelling.
3. Milliken & Milliken (1995). Racecar vehicle dynamics.

Tyre Report Sample

Uploaded by

Copyright:

Available Formats

Tyre Report Sample

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tyre Report Sample

Uploaded by

Copyright:

Available Formats

What are the main parameters that influence tire modeling for suspension design?

How does slip angle affect lateral force generation in tires?

PARAMETERS INFLUENCING TYRE MODELLING FOR SUSPENSION DESIGN

Saurabh Ranjan Sharma, AUE, For Student Formula Competetion 2015

SAE CO-ORDINATE SYSTEM

TIRE MODEL ADOPTED

VERTICAL TYRE STIFNESS

This rate is related to the overall ride rate of a vehicle by:

Maximum non-slide force, FY = 0.5cl2*

CS: Cornering stiffness coefficient

SLIP RATIO (% SLIP)

Slip in longitudinal plane

: Angular velocity of driven wheel

TOTAL LATERAL FORCE

Resultant of lateral force and pneumatic trail

Moment arm through which lateral force acts.

EFFECTIVE ROLLING RADIUS

You might also like