Scribd
Upload
64 views

Determinate Structures Are Analysed Just by The Use of Basic Equilibrium

Structures can be classified as determinate or indeterminate. Determinate structures can be analyzed using only equilibrium equations, while indeterminate structures require additional conditions like compatibility of deformations. Indeterminate structures include continuous beams, fixed beams, and frames with more supports than the number of equilibrium equations. Special methods are used to analyze redundant structures by considering the structure's material properties, cross sections, and other factors.

Uploaded by

Sougata Das
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
64 views

Determinate Structures Are Analysed Just by The Use of Basic Equilibrium

Structures can be classified as determinate or indeterminate. Determinate structures can be analyzed using only equilibrium equations, while indeterminate structures require additional conditions like compatibility of deformations. Indeterminate structures include continuous beams, fixed beams, and frames with more supports than the number of equilibrium equations. Special methods are used to analyze redundant structures by considering the structure's material properties, cross sections, and other factors.

Uploaded by

Sougata Das
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 10

Structure is an assemblage of a number of components like slabs, beams,

columns, walls, foundations and so on, which remains in equilibrium. It has to


satisfy the fundamental criteria of strength, stiffness, economy, durability and
compatibility, for its existence. It is generally classified into two categories
as Determinate andIndeterminate structures or Redundant Structures.
Any structure is designed for the stress resultants of bending moment, shear
force, deflection, torsional stresses, and axial stresses. If these moments,
shears and stresses are evaluated at various critical sections, then based on
these, the proportioning can be done. Evaluation of these stresses, moments
and forces and plotting them for that structural component is known as
analysis. Determination of dimensions for these components of these stresses
and proportioning is known as design.
Determinate structures are analysed just by the use of basic equilibrium
equations. By this analysis, the unknown reactions are found for the further
determination of stresses. Redundant or indeterminate structures are not
capable of being analysed by mere use of basic equilibrium equations. Along
with the basic equilibrium equations, some extra conditions are required to be
used like compatibility conditions of deformations etc to get the unknown
reactions for drawing bending moment and shear force diagrams.
Example of determinate structures are: simply supported beams, cantilever
beams, single and double overhanging beams, three hinged arches, etc.
Examples of indeterminate structures are: fixed beams, continuous beams,
fixed arches, two hinged arches, portals, multistoried frames, etc.
Special methods like strain energy method, slope deflection method, moment
distribution method, column analogy method, virtual work method, matrix
methods, etc are used for the analysis of redundant structures.

Indeterminate Structures: a structure is termed as statically indeterminate,


if it can not be analysed from principles of statics alone,
i.e.

. A statically indeterminate structure may be

classified as:
1. Externally indeterminate, (example: continuous beams and frames
shown in figure-1(a) and (b)).
2. Internally indeterminate, (example: trusses shown in figure-1(c) and
(d)).
3. Both externally and internally indeterminate, (example: trussed
beams, continuous trusses shown in figure-1 (e) and (f)).

Figure.1

EXTERNALLY INDETERMINATE STRUCTURES:

A structure is usually externally indeterminate or redundant if the reactions at


the supports can not be determined by using three equations of equilibrium,
i.e.

. In the case of beams subjected to vertical

loads only, two reactions can be determined by conditions of equilibrium.


Therefore, simply supported cantilever and overhanging beams shown in figure
2 are statically determinate structures.

Figure 2
If however a beam rests on more than two supports or in addition any of the
end support is fixed, there are more than two reactions to be determined. These
reactions can not be determined by conditions of equilibrium alone. The degree
of indeterminacy or redundancy is given by the number of extra or redundant
reactions to be determined. The beam shown in figure 3 (a) is statically
indeterminate to one degree because there are three unknown reactions and
statics has only two reactions. The beam in figure 3(b) is statically redundant to
two degree. The beam in figure 3(c) is redundant to three degree and the beam
in figure 3(d) is redundant to four degrees.

Figure 3
A portal frame is statically determinate if there are only three external
reactions, because there are three conditions of equilibrium for such a system.
The portal frame shown in figure 4 are statically determinate because there are
only three reactions to be determined. If a portal frame has more than three
reactions it is statically indeterminate, the degree of indeterminacy or
redundancy being equal to the number of redundant or extra reactions to be
determined. Therefore, the portal frames of figure 5(a) and (b) are redundant
by one degree, that of figure 5(c) is redundant by two degrees, that of figure
5(d) is redundant by three degrees, and that of figure 5(e) is redundant by 5
degrees.

Figure 4

Figure 5

The statically indeterminate beams and frames can be analysed by strain


energy method, three moment equation, slope deflection method or
moment distribution method.

INTERNALLY INDETERMINATE STRUCTURES:


A truss is statically determinate internally if the total number of members
m=2j 3
where j= number of joints.
A truss having more than (2j 3) members is statically indeterminate or
redundant, the degree of indeterminacy or redundancy being equal to the
number of extra members.

Figure 6
Thus the truss shown in figure 6(a) is statically redundant by one degree
because there are 14 members and 8 joints.
Number of redundant members = m= 2j 3
= 14 (16 3) = 1

Similarly, the truss shown in figure 6(b) is internally redundant by two degrees.
The internally indeterminate trusses can be analysed by strain energy
method.

EXTERNALLY AND INTERNALLY INDETERMINATE STRUCTURES


A truss is statically determinate, both externally and internally when
(a) All the reactions can be determined from the conditions of equilibrium,
namely

, and

(b) The total number of members, m= 2j 3, where j= number of joints.


The truss shown in figure 7 is externally indeterminate to one degree because
the numbers of reactions to be determined are three, and the conditions of
equilibrium reduces to two, namely

. This truss is also

internally indeterminate to one degree because there is one extra member.


Number of redundant member = m (2j 3)= 22 (2 x 12 3)= 1
Such trusses can be analysed by using strain energy method.

Figure 7

DIFFERENCE BETWEEN DETERMINATE AND INDETERMINATE


STRUCTURES
S.

Determinate Structures

Indeterminate Structures

Equilibrium conditions are fully adequate

Conditions of equilibrium are not

to analyse the structure.

adequate to fully analyse the structure.

Bending moment or shear force at any

Bending moment or shear force at any

section is independent of the material

section depends upon the material

property of the structure.

property.

The bending moment or shear force at

The bending moment or shear force at

any section is independent of the cross-

any section depends upon the cross-

section or moment of inertia.

section or moment of inertia.

Temperature variations do not cause

Temperature variations cause stresses.

No.

stresses.

No stresses are caused due to lack of fit.

Stresses are caused due to lack of fit.

Extra conditions like compatibility of

Extra conditions like compatibility of

displacements are not required to analyse

displacements are required to analyse

the structure.

the structure along with the equilibrium


equations.

You might also like