Scribd
Upload
103 views

What Is PID - Tutorial

Understanding PID control

Uploaded by

socrates19582405
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
103 views

What Is PID - Tutorial

Understanding PID control

Uploaded by

socrates19582405
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

What is PID - Tutorial

View this as a full page | ExperTune Home Page

What Is PIDTutorial Overview


PID stands for Proportional, Integral, Derivative. Controllers are designed to eliminate the need for continuous operator attention. Cruise
control in a car and a house thermostat are common examples of how controllers are used to automatically adjust some variable to hold the
measurement (or process variable) at the set-point. The set-point is where you would like the measurement to be. Error is defined as the
difference between set-point and measurement.
(error) = (set-point) - (measurement) The variable being adjusted is called the manipulated variable which usually is equal to the output of
the controller. The output of PID controllers will change in response to a change in measurement or set-point. Manufacturers of PID
controllers use different names to identify the three modes. These equations show the relationships:
P
I
D

Proportional Band = 100/gain


Integral = 1/reset
Derivative = rate = pre-act

(units of time)
(units of time)

Depending on the manufacturer, integral or reset action is set in either time/repeat or repeat/time. One is just the reciprocal of the other. Note
that manufacturers are not consistent and often use reset in units of time/repeat or integral in units of repeats/time. Derivative and rate are the
same.

Proportional Band
With proportional band, the controller output is proportional to the error or a change in measurement (depending on the controller).
(controller output) = (error)*100/(proportional band)
With a proportional controller offset (deviation from set-point) is present. Increasing the controller gain will make the loop go unstable.
Integral action was included in controllers to eliminate this offset.

Integral
With integral action, the controller output is proportional to the amount of time the error is present. Integral action eliminates offset.
CONTROLLER OUTPUT = (1/INTEGRAL) (Integral of) e(t) d(t)

http://www.expertune.com/tutor.html (1 of 5)3/7/2006 2:53:38 PM

What is PID - Tutorial

Notice that the offset (deviation from set-point) in the time response plots is now gone. Integral action has eliminated the offset. The
response is somewhat oscillatory and can be stabilized some by adding derivative action. (Graphic courtesy of ExperTune Loop Simulator.)
Integral action gives the controller a large gain at low frequencies that results in eliminating offset and "beating down" load disturbances. The
controller phase starts out at 90 degrees and increases to near 0 degrees at the break frequency. This additional phase lag is what you give
up by adding integral action. Derivative action adds phase lead and is used to compensate for the lag introduced by integral action.

Derivative
With derivative action, the controller output is proportional to the rate of change of the measurement or error. The controller output is
calculated by the rate of change of the measurement with time.
dm
CONTROLLER OUTPUT = DERIVATIVE ---dt
Where m is the measurement at time t.
Some manufacturers use the term rate or pre-act instead of derivative. Derivative, rate, and pre-act are the same thing.
DERIVATIVE = RATE = PRE ACT
Derivative action can compensate for a changing measurement. Thus derivative takes action to inhibit more rapid changes of the
http://www.expertune.com/tutor.html (2 of 5)3/7/2006 2:53:38 PM

What is PID - Tutorial

measurement than proportional action. When a load or set-point change occurs, the derivative action causes the controller gain to move the
"wrong" way when the measurement gets near the set-point. Derivative is often used to avoid overshoot.
Derivative action can stabilize loops since it adds phase lead. Generally, if you use derivative action, more controller gain and reset can be
used.
With a PID controller the amplitude ratio now has a
dip near the center of the frequency response. Integral
action gives the controller high gain at low
frequencies, and derivative action causes the gain to
start rising after the "dip". At higher frequencies the
filter on derivative action limits the derivative action.
At very high frequencies (above 314 radians/time; the
Nyquist frequency) the controller phase and amplitude
ratio increase and decrease quite a bit because of
discrete sampling. If the controller had no filter the
controller amplitude ratio would steadily increase at
high frequencies up to the Nyquist frequency (1/2 the
sampling frequency). The controller phase now has a
hump due to the derivative lead action and filtering.
(Graphic courtesy of ExperTune Loop Simulator.)

The time response is less oscillatory than with the PI controller. Derivative action has helped stabilize the loop.

Control Loop Tuning


It is important to keep in mind that understanding the process is fundamental to getting a well designed control loop. Sensors must be in
appropriate locations and valves must be sized correctly with appropriate trim.
In general, for the tightest loop control, the dynamic controller gain should be as high as possible without causing the loop to be unstable.
PID Optimization Articles

http://www.expertune.com/tutor.html (3 of 5)3/7/2006 2:53:38 PM

What is PID - Tutorial

Fine Tuning "Rules"


This picture (from the Loop Simulator) shows the effects of a PI controller with too much or too little P or I action. The process is typical
with a dead time of 4 and lag time of 10. Optimal is red.
You can use the picture to recognize the shape of an optimally tuned loop. Also see the response shape of loops with I or P too high or low.
To get your process response to compare, put the controller in manual change the output 5 or 10%, then put the controller back in auto.
P is in units of proportional band. I is in units of time/repeat. So increasing P or I, decreases their action in the picture.

http://www.expertune.com/tutor.html (4 of 5)3/7/2006 2:53:38 PM

What is PID - Tutorial

View this as a full page | PID Optimization Articles

Starting PID Settings For Common Control Loops

Home | Awards
Training | Connecting Your Controller
Articles | What They're Saying
Download Presentation | Information | Send us Mail
19992006 ExperTune, Inc.
Lake Country Research Center
1020 James Drive, Suite A
Hartland WI 53029-8305 USA
Telephone (262) 369-7711 Fax (262) 369-7722

http://www.expertune.com/tutor.html (5 of 5)3/7/2006 2:53:38 PM

You might also like