EE 742

Power System Components

Y. Baghzouz
ECE Department
UNLV

Desire to have a system with high reliability

and power quality
High reliability ensured by

High quality of components

High level of system security
Reserve of generation
Interconnection with large systems

High power quality ensured by

Well regulated voltage levels
Well regulated frequency
Minimal waveform distortion (low harmonics)

Structure of a Power System

Voltage levels:

Generation: 12-25 kV
Transmission: above 138 kV
Sub-transmission: 69-138 kV
Distribution: 4.16-69 kV
Utilization: below 4.16 kV

US Power Generation Mix

Transmission, Sub-transmission and Distribution

Common transmission voltages: 138kV,
245kV, 345kV, 500kV, 765kV
Common sub-transmission voltages: 69kV
Common distribution voltages: 34.5kV, 25kV,
13.8kV, 13.2kV, 12.47kV, 4.16k
Transmission power loss: 0.5%-1.5%
Distribution power loss: 4%-6%

North American Power Grid

Utilities learned the benefits in reliability and reduced operating

reserves by connecting to neighboring systems.
There are over 3,000 electric utilities in the US.
Some provide service in multiple states.
Over 1,700 non-utility power producers.
Utilities are either investor-owned, publicly-owned, and Federal utilities.
Electric utilities are regulated by local, State, and Federal authorities.

Electric Utilities in Nevada

90% of the states electric load is served by NV Energy
10% of the load is served by 15 small rural electric utilities

https://www.nvenergy.com/renewablesenvironment/renewables/images/renewables_map.pdf

North American Interconnections

The power system of North America is divided into four major

Interconnections which can be thought of as independent islands.
Western Generally everything west of the Rockies.
Texas - Also known as Electric Reliability Council of Texas (ERCOT).
Eastern Generally everything east of the Rockies except Texas and Quebec.
Quebec.

North American Balancing Authorities

The actual operation of the Interconnections is handled by over 100

Balancing Authorities (BAs). The BAs dispatch generators in order to meet
their individual needs. Some BAs also control load to maintain balance.

1000

0
Hour of Day

Time (mm/dd/yy)

9/28/2008

9/21/2008

9/14/2008

9/7/2008

8/31/2008

8/24/2008

8/17/2008

8/10/2008

8/3/2008

7/27/2008

7/20/2008

7/13/2008

7/6/2008

6/29/2008

3000

6/22/2008

4000

6/8/2008

6/1/2008

5000

System demand (MW)

6000

6/15/2008

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

System Load (MW)

Demand

Changes in demand of individual customers is fast and frequent

The aggregated demand is smoother, and total load fluctuations
are usually small.

6000
5000
4000

3000

2000

2000

1000

Generation-load balance
As electricity itself cannot presently be stored on a large scale, changes in
customer demand throughout the day and over the seasons are met by
controlling conventional generation, using stored fuels.
Frequency is maintained as long as there is a balance between resources
and customer demand (plus losses). An imbalance causes a frequency
deviation.
The overall daily profile of load in a given area can be predicted reasonably
well using forecasting tools.
A day-ahead generating schedule can be developed based on the
predicted next-day load profile.

Frequency: the heartbeat of a power System

The figure below shows a sample time history of the frequency on the
grid in the western United States, sampled six times a second. The slope of
the frequency trace is a measure of the overall imbalance of generation
and load at any given moment.
The actual grid frequency tends to oscillate slightly around 60 Hz. The
frequency error from 60 Hz is used to fine-tune the generation level
through regulation.

Source: Alec Brooks, Ed Lu,Dan Reicher, Charles Spirakis, and Bill Weihl,Demand Dispatch IEEE Power &
Energy magazine, May/June 2010

Optimal generator scheduling & Dispatching

Given a power system with n generators, and a load forecast, the problem is
to determine the optimal schedule of each generator while recognizing
generating unit limits and output capability.
6000
5000

4000
3000

2000

Base Load

1000

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

System Load (MW)

Hour of Day

Unit # x
Unit # y
Unit # z

Generation fleet characteristics

Each generating unit has specific (fixed) physical characteristics
that determine the capability of each unit to respond to changes
in system load in the up or down direction:

Minimum generation Pmin (MW)

Maximum generation Pmax (MW)
Maximum ramp rate R (MW/min)
Scheduled operating point - Psched (MW)
Regulation reserve (MW)
Load following reserve (MW)
Contingency reserve Pcont (MW)

Reserve allocation in scheduling process

Operating Reserve Requirements

BAs are required to maintain the following types of reserves

(typically 10-15% of peak load) to provide for regulation, balance
against the load forecasting error and to maintain local area
reliability:
Spinning Reserve Unloaded generation that is synchronized,
automatically responsive to frequency deviations (AGC), and
ready to serve an additional demand.
Non-Spinning Reserve (1) The generating reserve, which is not
connected to the system but capable of serving the demand
within a specified time from its activation; and (2) loads that can
be removed from the system within a specified time.

Interchange error
Customer demand and generation are constantly changing
within all BAs.
BAs will have some unintentional outflow or inflow at any
given instant.
A Balancing Authoritys internal obligations is to control an
instantaneous value called the Area Control Error (ACE) by
keeping it within acceptable limit that is proportional to the BA
size (44 MW for NV Energy South?).
Conceptually, the ACE informs the Balancing Authority what the
frequency is doing in the Interconnected system. For example,
over-generation makes ACE go positive and puts upward
pressure on Interconnection frequency.
Tie-line
M
Scheduled net flow: 350 MW
Actual net flow: 340 MW
(due to load reduction)

ACE goes positive

Frequency goes up

Reduce generation

Power system operation Real time

In real time, the level of generation is adjusted to meet differences
between actual loads and the hourly schedules. This real-time
adjustment, can be separated into load following (within-hour
resource dispatching) and regulation (sub-minute adjustments of
generation) processes according to their respective time scales.
Load following typically requires adjustments every 10
minutes. This is accomplished through a re-dispatch of on-line
generation via automatic adjustments by computerized
control systems.
Regulation is effected by making sub-minute output
adjustments exclusively through an automatic generation
control (AGC) system.
During real time operation, generators under AGC are adjusted every
2 or 4 seconds (although their actual responses are slower) to keep
the ACE close to zero.

Illustration of Regulation and Load Following

Load following is the difference between 10-minute interval average
and 60-minute average (both with ramps) of load, depicting the
variation of load within the hour at a 10-minute time scale.
Load Following = [real-time schedule] [hourly schedule]
Regulation = [actual load] [ real-time schedule]

Note that the regulation ramps (i.e. slopes) are significantly higher
than those of load following

Assessing Adequacy of Ramping Capability

Insufficient ramping capability is identified when the ramp
requirements exceed generation fleet ramping limits.
The figure below illustrates how such a deficiency could occur: the area
in red highlights the magnitude and duration of the interval when
regulation ramp requirements exceed fleet capability.
More units and capacity are needed if composite unit ramping
capability is insufficient,

Power Generation Unit (hydro/steam/gas)

Rotating and Static Excitation Systems

Power rating: typically less than 1% of
generator rating.
Voltage rating: less than 1 kV

Block diagram of excitation and AVR system

The AVR regulates generator voltage by controlling
the amount of field current.
Regulation is stabilized using feedback loops.
Limiters are used to protect the system from
excessive currents and voltages.
The PSS helps with the damping of power swings
in the system.

Dynamic voltage response to step change in

reference value
For small disturbances, the quality of voltage regulation can be
assessed by observing the voltage response of a generator to a step
change in the reference value.
The quality of regulation is assessed by four indices for a given
accuracy:

Rise time
Time to reach peak value
Settling time
overshoot

HW # 2
Assume the following transfer function relating the
generator terminal voltage to the reference voltage:
V (S )
100
2
Vref ( S ) S 10S 100

Determine the rise time, time to reach peak

value, settling time, and overshoot for a step

change in reference voltage (i.e., vref(t) = u(t)).
Allow the error = 1%

Turbines and their Governors

Steam turbines can have non-reheat, single-reheat or double-reheat.
The steam flow is controlled by the governor. The main amplifier of the
governing system and valve mover is an oil servomotor that is
controlled by a pilot valve.
Main and reheat stop valves are normally fully open. The are used only
during generator start-up and shut down.

Open- and Combined-Cycle Gas turbines

Open cycle gas turbine plant efficiency 35%
Combined cycle gas turbine plant efficiency 60%
Combined cycle gas turbine plants have shorter construction time,
lower capital construction, relatively clean, little staffing and the
materials handling problem is much simpler than coal fired plants.
Some plants use heat exhaust for process industry in the vicinity, while
others use steam for district heating.

Hydro Turbines

Head: vertical distance between upper reservoir and level of turbine

Francis Turbine

Block diagram of mechanical-hydraulic and electro-hydraulic

speed governing systems

Turbine Characteristics

See graph below: unregulated turbine (line 1-2), regulated turbine (line 4-3-2)
Role of turbine governor: stable operation in line 3 (with small droop).
Droop (or speed droop coefficient) :

Effective gain (reciprocal of droop) K:

K 1/

Equilibrium point between turbine and load power

The droop should be made small (but cannot be zero or negative)
Load power has a very high positive slope in the (, P) plane.
At the equilibrium point, the opposing electromagnetic and
mechanical torques acting on the shaft are equal in magnitude.
In Fig. (a) with small positive droop, a change of frequency brings the
system back to the equilibrium point.
In Fig. (b) with a small negative droop, a change on frequency results
in system instability.

Block Diagram Transformation

HW # 3
Derive the transfer function of the system
below.

Simplified model of turbine governing system

Ignore steam flow feedback (in electro-hydraulic governing system) and

governor response is dominated by the time constant of the servomotor.
Fig. (a) below (where KA and R represent correspond to the gain in
servomotor amplification and gain in the feedback loop) can be simplified to
Fig. (b) where the effective time constant TG = 1/(KAR)
At steady-state (t, s0), Fig. (b) is simplified to Fig. (c). Assuming
linearity between valve position and mechanical power,
/ n ( R / n )c c Pm / Pn

Transformers
Step-up transformer: connects generator to the transmission network.
Transmission transformer: connects transmission networks with different
voltage levels
Substation transformer: connects the transmission network to the
distribution network
Distribution transformers: connects the distribution network to
customers
Auto-transformer: typically used when the voltage ratio is less than 2.
Two-winding Transformer

Auto-Transformer

Regulating Transformer
The under-load-tap-changing transformer(ULTC), also called the on-load
tap Changer (OLTC) or load tap changer(LTC), allows the taps to be
changed while the transformer is energized. A typical range of regulation
is 10% with 32 steps - each corresponds to (5/8)%.

Diverter and Selector

Switch Combined into
One Unit.

Phase-Shifting Transformer
Phase shifting transformers change the phase angle between the primary
and secondary voltages in order to control the flow of real power. They can
also be used to control the voltage ratio, hence reactive power flow.

Series and Shunt Elements

Shunt reactors are used in long and lightlyloaded transmission lines to lower the voltage.
Shunt capacitors are used in heavily loaded
transmission lines to raise the voltage.
Series capacitors are used in long transmission
lines to offset some of the line inductance thus
allowing more power flow.
Capacitor overvoltage protection during faults is
provided by either spark gaps (G) or Zinc-Oxide
Varistors (R) with a breaker switch (S).

FACTS Devices: SVC

FACTS Devices: STATCOM

FACTS Devices: BESS

FACTS Devices: TCBR

FACTS Devices: UPFC

System Protection
Protective equipment needs to detect a
fault and disconnect the faulty element.
Protection equipment consists of current
and/or potential transformers, relays,
auxiliary power supplies for the relays,
and circuit breakers.
Operation of the protection scheme
must be
fast,
reliable,
and selective.

Protection of transmission lines

Differential current protection (for short line) uses pilot wires and analog
signals.
Interlock scheme (for longer lines) uses power line carrier (PLC) - high frequency
(20-200 kHz) logic signals need for line traps.
Phase comparison scheme (i.e., phase angle between currents at both ends of
the line) also use PLC.
Fiber optics placed inside the ground wire are replacing pilot wires and power
line carriers.

Transformer Protection
The main form of transformer protection is differential current
protection (similar to the current differential protection used to
protect a transmission line).
The protection scheme takes into account
The magnitude and phase angle of the current on each side.
The presence of large magnetizing inrush currents
The transformer is protected against inter-turn faults by the
Buchholz protection a safety device that detects the build-up
of gases inside the transformer.
Transformers are also equipped with ground fault protection
(supplied with zero-sequence current), overload protection, and
thermal protection.

Generator Protection

Differential protection against faults inside the generator,

Over-current and asymmetry protection of stator windings,
Over-current protection of rotor windings
Additional protection systems are used to protect the
generator from loss of excitation, loss of synchronism (poleslip protection), faults in stator windings (under impedance
protection), earth faults in the rotor windings and from failure
of the prime mover (motoring protection).
The generator is also equipped with protection from nonelectrical disturbances due to lubrication oil failure, loss of
boiler fire, over speeding, rotor distortion, excessive vibration
and difference in expansion between rotating and stationary
parts.

System monitoring & Control

The possibility of measuring

synchronized voltage and current phasors
using GPS/GIS has led to new innovative
ways of monitoring, protecting, and
controlling power systems.