HyperMesh Geometry Cleanup

Tutorial - 2
Geometry clean-up & Mid-Surface.

Open and view the model file, clip.hm.
View the model in topology display toolbar and shaded mode to evaluate its integrity.
1.
2.
Observe where the model has incorrect connectivity and missing or duplicate surfaces.
Click Geom page and then click on autocleanup to open the Auto Geometry Cleanup panel.
Note that the surface edges are now colored according to their topology status. This occurs because Geometry Color is set to
auto
3.
Now click on the drop down arrow just beside Auto and select Mixed
edges with the specified colour. (The colour scheme is explained below)
4.
Click Wireframe Geometry

to display the model in Wire frame mode.
The toolbar contains icons that control the display of the surfaces and surface edges. Surfaces can be shaded with or without
edges or wireframe. Right-click the icons to access the drop-down menu for additional options. Place your mouse over the
cursor to view a description of the buttons functionality.
5.
Click Visualization
and navigate to the Topology tab.
Visualization controls the display of the surfaces and surface edges. Surfaces can be shaded or wireframe. The check boxes
within this menu turn the display of the different edge types and fixed points (surface vertices) on or off.
Clear all the check boxes except the Free check box.
6.
7.
8.
, this will show the
Only the free edges should be displayed at this point.

Observe the free edges and make note of where they are.
The free (red) edges show where there is incorrect connectivity or gaps.
Note the locations where there are closed loops of free edges. These are locations that probably have missing surfaces.
Free edges indicating surface discontinuities of the clip geometry.
9. Select only the Non-manifold check box.

10. Observe the non-manifold edges and make note of where they are.
The non-manifold edges show where there are more than two surfaces sharing an edge, which might indicate incorrect
connectivity. For this part, there are yellow edges completely surrounding two areas. This indicates that there are probably
duplicate surfaces in these locations.
11. Select all the check boxes.

12. Click the Close button to close the Visualization tab.
13. Click return to exit the panel.
14. Click Shaded Geometry and Surface Edges
The surfaces should now appear solid rather than having only their edges displayed.
15. Rotate, zoom, and pan to locate any errors in the geometry.
16. Make note of the areas to be worked on:
A surface that overhangs a round corner.
A missing surface.
An edge that has apparently been collapsed.
Surface overhanging an edge and a missing surface
Area of collapsed edge
Delete the surface that overhangs the round corner

1.
Enter the Delete panel in one of the following ways:
2.
From the menu bar click Geometry > Delete > Surfaces.
Press F2.
Click on the drop down arrow, and select surfs from the list.
3.
In the graphics area, select the overhanging surface shown
4.
5.
Click delete entity to delete the selected entities.

Click return to exit the panel.
Create surfaces to fill large gaps in the model

1.
Go to Geom page, here click on surfaces panel.
2.
Now here click on Spline/Filler option to generate the missing surface.
3.
Click the Keep tangency check box.

The Keep tangency option examines surfaces attached to the selected edges and tries to create a surface tangent to them.
This helps to form a smooth transition to the surrounding surfaces. (Note : Sometimes if the check box of keep tangency is on, it may be
possible that it will not generate the surface, so just uncheck it so that it will generate the surface).
4.
5.
6.
Verify the entity type is set to lines.

Verify the Auto create (free edges) check box is selected.
The Auto create option simplifies the selection of the lines bounding the missing surface. Once a line is selected, HyperMesh
automatically selects the remaining free edges that form a closed loop, and then create the filler surface.
Zoom into the area indicated in the following image.
Area of missing surfaces
7.
Pick one of the red lines bounding one of the gaps (missing surfaces).
8.
9.
HyperMesh automatically creates a filler surface to close the hole.

Repeat sub-step 7 to create a filler surface in the other gap.
Set the global geometry cleanup tolerance to 0.01.

1.
Press O to go to the Options panel.
2.
3.
Go to the geometry subpanel.

In the cleanup tol = field, type 0.01 to stitch the surfaces with a gap less than 0.01.
4.
Combine multiple free edge pairs at one time with the equivalence tool.
1.
Go to Geom page, here select edge edit.
2.
Here select the equivalence radio button
3.
4.
5.
6.
Activate the equiv free edges only check box.

Select surfs >> all.
Verify that the cleanup tol= is set to 0.01, which is the global cleanup tolerance specified in the Options panel.
Click the green equivalence button to combine any free edge pairs within the specified cleanup tolerance.
Most of the red free edges are combined into green shared edges. The few remaining are caused by gaps larger than the
cleanup tolerance.
Combine free edge pairs, one pair at a time, using the toggle.
1.
Go to the toggle subpanel.
2.
In the cleanup tol = field, type 0.1.
3.
In the graphics area, click one of the free edges shown in the following image.
Rotate and zoom into the area if needed. When the edge is selected, it will change from red to green, indicating that the free
edge pair has been equivalence.
Area where free edges need to be toggled
Combine the remaining free edge pair using replace

1.
Go to the replace subpanel.
2.
In the Model Browser, click
3.
4.
5.
6.
7.
With the selector under moved edge: active, click the leftmost free edge in the graphics area.
Verify that the selector under retained edge: is now active.
Select the rightmost red edge.
In the cleanup tol = field, enter 0.1.
Click replace.
Once the line is selected, HyperMesh posts a message similar to:
"Gap = (.200018). Do you still wish to toggle?"
Click Yes to close the gap.
8.
next to the View2 saved view
Edges to retain and move for replacement
9.
Find and delete all duplicate surfaces

You should still be in the Geom Cleanup panel.
1. From the menu bar, click Geometry > Defeature.
2.
Click on the duplicate radio button to activate the duplicate command.
3.
4.
5.
Click surfaces >> displayed.

In the cleanup tol = field, type 0.01.
Click find.
The status bar displays the following message, "2 surfaces are duplicated.".
Click delete to remove any duplicate surfaces.
6.
Observe the model again to identify any remaining free edges, or missing or duplicate surfaces.
1.
2.
Use the topology display and shaded modes to perform this task. All of the edges in the model should be displayed as green
shared edges, indicating that we have a completely enclosed thin solid part.
Generating a Midsurface
Generate a midsurface from midsurface panel.
1.
From the menu bar, click Geometry > Create > Midsurfaces > Auto.
2.
3.
4.
Verify that the closed solid option and the yellow surfs selector are active.
Select one surface from the graphics area.
Click extract to start the midsurface generation.
The midsurface is created, and the surfaces are organized into a new Middle Surface component. Note that when a midsurface
is created, transparency is turned on for all the other components in the model except the new Middle Surface component.
The next step covers how to control surface transparency.
Review the parts midsurface

1.
From the Model Browser, turn off the display of geometry in the component named lvl10 to display only the Middle Surface
component.
The midsurfaces generated for the solid sections of the model using the auto-midsurface subpanel are shown in the following
image.
Midsurface generated from a volume of surfaces
3.
Turn the geometry for lvl10 component back on from the Model Browser.
4.
5.
On the Visualization toolbar, access the Transparency panel (

).
With the comps selector active, select a line or surface of the lvl10 component in the graphics region.
You may need to zoom in on the model to select a valid entity.
Since the entity selector is set to comps, selecting a line or surface in the component selects the entire component.
In the panel, click the arrow button on the right under transparency several times.
You should see the surfaces in the lvl10 component becoming more and more transparent.
6.
7.
You can also drag the slider back and forth to control the level of transparency.
Rotate, zoom, and pan to visualize the midsurface.

HyperMesh Geometry Cleanup

Uploaded by

Copyright:

Available Formats

HyperMesh Geometry Cleanup

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HyperMesh Geometry Cleanup

Uploaded by

Copyright:

Available Formats

Tutorial - 2

Geometry clean-up & Mid-Surface.

Click Wireframe Geometry

, this will show the

Only the free edges should be displayed at this point.

Free edges indicating surface discontinuities of the clip geometry.

9. Select only the Non-manifold check box.

11. Select all the check boxes.

Area of collapsed edge

Delete the surface that overhangs the round corner

Enter the Delete panel in one of the following ways:

In the graphics area, select the overhanging surface shown

Click delete entity to delete the selected entities.

Create surfaces to fill large gaps in the model

Go to Geom page, here click on surfaces panel.

Now here click on Spline/Filler option to generate the missing surface.

Click the Keep tangency check box.

Verify the entity type is set to lines.

Area of missing surfaces

HyperMesh automatically creates a filler surface to close the hole.

Set the global geometry cleanup tolerance to 0.01.

Press O to go to the Options panel.

Go to the geometry subpanel.

Click return to exit the panel.

Go to Geom page, here select edge edit.

Here select the equivalence radio button

Activate the equiv free edges only check box.

Go to the toggle subpanel.

In the cleanup tol = field, type 0.1.

Area where free edges need to be toggled

Combine the remaining free edge pair using replace

Go to the replace subpanel.

In the Model Browser, click

next to the View2 saved view

Edges to retain and move for replacement

Click return to exit the panel.

Find and delete all duplicate surfaces

Click on the duplicate radio button to activate the duplicate command.

Click surfaces >> displayed.

Review the parts midsurface

Midsurface generated from a volume of surfaces

On the Visualization toolbar, access the Transparency panel (

You might also like