Tanker

CUSTOMER SERVICE INNOVATION MANUFACTURING QUALITY TECHNICAL EXPERTISE EXCELLENCE DESIGN
Tanker & Overfill

Prevention
Products
Customer Service: +44 (0)1772 323529
4
2
Telephone: +44 (0)1772 323529
Fax: +44 (0)1772 314664
Tanker & Overfill

Prevention Products
Tanker & Storage Tank Products.................................................................... 4
Dry Bulk Products.................................................................................. 5-13
Bayco Petroleum Products................................................................. 14-22
FloTech Overfill Prevention Products............................................... 23-35
Swivel Joints....................................................................................... 36-41
Dry Disconnect Couplings................................................................... 42-43
Dry Disconnect Adapters............................................................................ 44
Dry Break Cam & Groove Couplings................................................... 45-46
Dry Break Cam & Groove Adapters ........................................................... 47
Aluminium Storz Couplings................................................................. 48-51
Tank Wagon Couplings EN 14420-6:2004................................................... 52
Tank Wagon Spares & Seals EN 14420-6:2004........................................... 53
Low Pressure Tank Equipment.................................................................... 54
Telephone: +44 (0)1772 323529
Fax: +44 (0)1772 314664
Tanker & Overfill Prevention Products

Tanker & Storage Tank Products
Dixon offers a comprehensive range of equipment for use on dry bulk & petroleum
tankers including overfill protection equipment. The range is supplemented by an
excellent range of storage tank equipment including, pressure & vacuum relief valves,
emergency relief valves and gauge hatches.
Dry Bulk Tanker Products
Petroleum Tanker Products
Low Pressure Tank Equipment
Air Relief Valves.
API Valves / Drop Adapters.
Vacuum Relief Valves.
Vacuum Relief Valves.
Vapour Valves, Couplers & Caps.
Pressure Relief Valves.
Caps, Adapters and Reducers.
Vapour Elbows & Air Interlocks.
Combined Pressure and Vacuum.
Filtration Systems.
Shut off and pressure Nozzles.
Emergency Relief Valves.
Swing Check Valves.
Flanged Sight Flow Indicators.
Gauge Hatches.
Butterfly Valves.
Pipe Caps & Reducers.

FloTech Overfill Prevention.

Dry Bulk
Dixon Dry Bulk products are designed for use with bulk trailers and truck blowers for the
pneumatic transfer of dry bulk commodities such as powders, grains and plastic pellets.
Other industrial applications are possible when pneumatic control of air or dry products
is required.
Hose Accessories
Air and Vacuum Relief Valves
Pneuclean
Filter Systems
Tube Doors
Fluidisers
Butterfly Valves and Hopper Tees

Swing Check Valves

Air Relief Valves
Designed to relieve air pressure at a specific pressure setting (customer to advise when ordering typical setting 15-25 psi)
Air Relief Flow Rates:
A2180 up to 500 SCFM
A choice of setting tolerances are provided. In addition to conventional field duty tolerances of +3/-0 psi, offers OEM
tolerances of +1/-0 psi. The tighter tolerance air reliefs are designated with the prefix A, (A2180, A3180, A2182). Both
conventional field duty and OEM tolerance products are of identical construction, however OEM models are identified
with an A imprinted before the setting stamp
NOTE: Adjustable models, (A2180ADJ, A3108ADJ) are only available with OEM settings
Relief Valve Flow Rates vary depending on the preset relief pressure, for specific relief rates contact Dixon.
Features:
High Grade Diaphragms White, food grade, and high
temperature elastomers for all models
Tamper proof stainless steel cup seals

Available in a female thread version
Suitable for high temperature (to 200C) and food
Model 2182 has Silicon rubber poppet which
grade service
reduces tendency to cake cement, lime etc
Safety Note: Air/vacuum relief valves must be regularly inspected, cleaned and maintained. Product particles can prevent the valve from fully reseating which
can lead to early opening/leakage from the valve or can prevent it from opening at all. For ease of removal and installation, to allow for inspections, cleaning
and maintenance all 2180 and 2182 series air relief valves are available with either male cam and groove or victaulic grooved connections.
Designed for trailer service
CUP SEALS
PART No.
Description
2180/xx
A2180/xx
3180/xx
A3180/xx
2
2
3
3
PART No.
Description
2180V/15
2 Grooved End
Female
Female
Female
Female
NPT
NPT
NPT
NPT
Shown with optional Safety Lanyard

(CAL25) attached.
Set at 15 psi
PART No.
Description
2180B/15
2 Adapter
Shown with optional Safety Lanyard

(CAL25) attached.
Set at 15 psi
PART No.
Description
A2180/xxADJ
A3180/xxADJ
2 Female NPT
2 Female NPT
CUP SEALS
Adjustable models allow an adjustment of + or - 3 psi from specified setting. Designed for trailer service.
/xx refers to the choice of pressure settings provided. Please request the required settings when ordering.

Designed for high capacity blower or trailer service

PART No.
Description
PART No.
Description
2182/xx
A2182/xx
2182B/xx
2182V/xx
2 Male NPT
2 Male NPT
2 Adapter
2 Grooved End
2182F/xx
2 Female NPT
/xx refers to the choice of pressure settings provided. Please request the required settings when ordering.
Pneuclean Pneumatic Filtration System

The Pneuclean unit is designed to remove microscopic particles generated by blowers during pneumatic conveying of
contaminant-sensitive dry bulk products. Contaminants such as Iron and Hydrocarbons are produced by blowers and can
adversely affect dry products such as plastic pellets and food materials.
These filter units are typically used on dry bulk tanker trucks and placed after the blower and before the bulk storage
tanker. This in-line pneumatic system is also suitable for industrial applications or wherever microscopic filtration (up to 4
microns) of impurities is required.
Standard units employ 4 inlets and outlets. However, 3 plumbing can be used with available weld-on 4 x 3 female
NPT adapters.
Special cartridge-style filter elements have a typical life expectancy of approximately 12 months or 2000 hrs. of service.
4 AW and 4 DW Aluminium fittings may be butt-welded to filter inlet to allow quick coupler connection of hose.
4 inlet (can be converted

to 3 by use of
4 x 3 adapter)
Stainless Steel
cartridge with
microporous,
semi-permeable
PTFE membrane
filter element.
4 outlet (can be converted to 3

by use of 4 x 3 adapter)
PART No.
Description
PC5000
PART No.
replacement parts Description
PC5001
PC5003
PC5004
PC5005
PC5006
PC5007
4 Pneuclean complete housing with filter
Filter
Mounting Bracket
V-clamp
Lid O-ring
Bottom Gasket
Lid w/Adjusting nut
In-Line High Pressure Air Filtration for 4 Air Lines

FDA Medium with 99.99% maximum efficiency at 4 microns.
Average 12 month filter cartridge lifespan
Maximum air flow 1000 CFMs
Quick release V-clamp for easy inspection
Back pressure only .05 psi
Overall weight 26 lbs (11.8kg)
Temperature range -45 to 230C

Swing Check Valves
High flow body design
Easy maintenance inspection lid
Drop in flapper assembly
Captive springs and shaft to prevent contamination
High temperature white food grade seal
Stainless Steel hardware
SWING CHECK VALVES

3030SQ
3090MA
PART No.
3030SQ
3090M
3090MA
3090MB
3030SK
3090MS
3090MAS
3090MBS
Description
3 Square Flange Swing Check Valve
3 Swing Check Manifold
3 Swing Check Manifold with 3 Adapter
3 Swing Check Manifold with 4 Adapter
Security Kit For 3 Swing Check Manifold
3 Swing Check Manifold with Security Kit installed
3 Swing Check Manifold with 3 Adapter and Security Kit installed
3 Swing Check Manifold with 4 Adapter and Security Kit installed
3 and 4 Swing Check Valves

Cast Aluminium bodies with Bronze inspection caps
Safety flapper assembly - all flapper assemblies are drilled and pinned and will
not come apart
Choice of seals: metal-to-metal, Buna or Silicon Rubber seals
Choice of models with or without spring loaded flapper
Full flow design - flappers swing out of flow path for maximum flow and
low resistance
Designs with large caps allow flapper repair/rebuild on unit
Check valves allow one way directional flow only. They are used as a protective safety device to prevent flow reversal should back pressure result.
These valves are designed specifically for service with pneumatic equipment which transfers dry bulk commodities.
3 ROUND FLANGED (TTMA)

PART No.
3000N
3000SP
3000B
3000S
3000BSP
3000SSP
Description
Metal-to-metal seal
Metal-to-metal seal & spring loaded flapper
Buna Rubber seal
Silicon Rubber seal
Buna seal & spring loaded flapper
Silicon Rubber seal & spring loaded flapper
3 SQUARE FLANGED (TTMA)

PART No.
3001SQN
3001SQSP
3001SQB
3001SQS
3001SQBSP
3001SQSSP
Description
Metal-to-metal seal
Buna Rubber seal
Silicon Rubber seal
3 Threaded Ends (NPT)

PART No.
3000TE
3000TESP
3000TEB
3000TES
3000TEBSP
3000TESSP
Description
Metal-to-metal seal
Buna Rubber seal
Silicon Rubber seal
Gaskets should be purchased separately.
4 Round Flanged (TTMA)

PART No.
4040RD
Description
4 Threaded Ends (NPT)

PART No.
4040TE
Description
Silicone seal, spring loaded flapper
2 Swing Check Valves

A
luminium cast, square flanged and threaded end models
S
elf-aligning, moulded white food grade EPDM rubber flapper assembly
(176C / 350F) with externally mounted springs, to prevent ingestion of parts
Easy open (no tools required) inspection cap
Full flow performance
2 SWING CHECKS
PART No.
3020SQ
3020TE
Description
2 Square Flange
2 Female NPT

Horizontal Swing Check Valves
Swing Check Valves are designed to prevent backflow
in plumbing and liquid piping systems, while offering full
flow performance with a minimum of turbulence
or pressure loss
For horizontal or vertical use

Rated to 200 psi WOG
Brass body & disc
A positive seating disc allows flow only in one
Temperature range (-4C to 66C / -20F to 150F)
direction and a screw-in cap provides easy access

for periodic cleaning
Female NPT x Female NPT

PART No.
Description
SWCV50
SWCV75
SWCV100
SWCV125
SWCV150
SWCV200
SWCV300
1/2
3/4
1
11/4
11/2
2
3
In-line Sight Glass

Designed for dry bulk transfer applications
Available in combination of 3 and 4 coupler or adapter ends
Includes:
Aluminium bodies
Buna seals
Acrylic sight glasses
Stainless steel hardware
Bronze cam arms (where applicable)
10
PART No.
Description
3544CA
3533CA
3543CA
3534CA
3533AA
4 Coupler x 4 Adapter
3 Adapter x 3 Adapter
3544AA
3534AA
3544CC
3533CC
3543CC
4 Adapter
3 Adapter
4 Coupler
3 Coupler
4 Coupler
x
x
x
x
x
4
4
4
3
3
Adapter
Adapter
Coupler
Coupler
Coupler

Butterfly Valves - 400 Series
Housing:
Aluminium
Discs:
Type 316 Stainless or Nodular Iron
Stem Packing:
Buna-N
Stem Bushings:
Thermal plastic polymer, top and bottom
Resilient Seat:
Nitrile
Handle: High strength 713 Alloy Aluminium with retrogressive re-aging process - stronger
than industry standard Cast Iron handles. Stainless Steel spring and locking lever pin
Throttling Plate: Five position, high strength Aluminium Alloys
Features:
Aluminium Body
N
odular Iron Disc
1
7-4 SS Stem
N
itrile, FDA approved Black Seat
nodular iron
complete valve with
nodular iron disc
PART No.
2-400-1500
3-400-1500
4-400-1500
4A-400-1500
5-400-1500
6-400-1500
nodular iron
replacement discs

SIZE
2
3
4
4 TTMA
5
6
PART No.
2-400-422237F
3-400-422237F
4-400-422237U
5-400-422237U
6-400-422237U
SIZE
black
Replacement Nitrile Seats

PART No.
2-400-422500
3-400-422500
4-400-422500
4A-400-422500
5-400-422500
6-400-422500
2
3
4
5
6
SIZE
2
3
4
4 TTMA
5
6
Handles should be ordered separately.
Features:
A
luminium Body
3
16 SS Disc
1
7-4 SS Stem
N
itrile, FDA approved White Seat
stainless steel
complete valve with
316 stainless steel disc
PART No.
SIZE
3-400-3501
4-400-3501
5-400-3501
6-400-3501
3
4
5
6
316 stainless steel

replacement discs
PART No.
2-400-422209F
3-400-422209F
4-400-422209U
5-400-422209U
6-400-422209U
SIZE
2
3
4
5
6
White
Replacement Nitrile Seats
PART No.
2-400-422501
3-400-422501
4-400-422501
4A-400-422501
5-400-422501
6-400-422501
SIZE
2
3
4
4 TTMA
5
6
11

Butterfly Valves - 390 Series
Housing:
Aluminium
Discs:
Type 316 Stainles
Body Screws:
Cadmium Plated Steel
Stem Packing:
Buna
Stem Bushings:
Thermal plastic polymer, top and bottom
Resilient Seat:
Nitrile
Handle: High strength 713 Alloy Aluminium with retrogressive re-aging process - stronger than
industry standard Cast Iron handles. Stainless Steel spring and locking lever pin
Throttling Plate: Five position, high strength Aluminium Alloy
Features:
2 Piece Aluminium Body
One piece 316 SS Disc and Stem
N
itrile, FDA approved White Seat
Stainless Steel
complete valve with
316 SS disc

PART No.
316 stainless steel

replacement discs

SIZE
3-390-828501
4-390-828U501
5-390-828U501
6-390-828U501
PART No.
SIZE
3-390-209F
4-390-209U
5-390-209U
6-390-209U
3
4
5
6
white replacement
nitrile seats

PART No.
SIZE
3-400-422501
4-400-422501
5-400-422501
6-390-363501
3
4
5
6
3
4
5
6

For 6 390 series valve, use special handle 400-206-65.
dimensions & weights

dimensions
Size
2
3
4
5
6
weight
in lbs.
4.000
4.000
4.000
4.000
4.000
.375
.375
.438
.438
.438
.563
.563
.625
.625
.625
1.250
1.250
1.250
1.250
1.250
3.938
4.875
6.000
6.000
6.500
4.125
5.375
6.875
7.625
8.750
2.125
3.125
4.125
5.188
6.125
1.625
1.750
2.000
2.125
2.125
1.688
2.875
3.875
5.000
6.000
3
4
7
9
9
NOTE: Q dimension is the minimum allowable inside diameter of the pipe or mating flange.
12

Butterfly Valve Accessories
Aluminium Handle Kit

PART No.
SIZE
206-23-5
206-46-5
400-206-65*
2 and 3
4 thru 6
6 - 390
BUSHING & PACKING KITS

PART No.
SIZE
2-3-400-99-BPKIT
4-6-400-99-BPKIT
6-99-400BPKIT*
2 and 3
4 thru 6
6
316 STAINLESS SCREW SETS

PART No.
SIZE
2-3-213
4-5-6-213
2 and 3
4 thru 6
17-4 STAINLESS STEMS

PART No.
2-400-422240
3-400-422240
4-400-422240
5-400-422240
6-400-422240
SIZE
2
3
4
5
6
Includes handle plate kit and handle/lever assembly.

*Use on 6 390 series valves
13

Dixon products are engineered for dependable,
long service life and designed for easy,
low cost maintenance. Where possible, modular
systems are incorporated with common parts
to minimise inventory of repair items.
14

4 api Valves
API Valves are used for bottom loading and unloading of petroleum tankers. Valve nose shape and opening comply with
American Petroleum Institute standard (API RP-1004) enabling Dixon API valves to interchange with competitor items
made to the same specification. Two styles are available; a load only model without handle and a load/unload model
with a handle to allow manual opening.
Unique flow and fluid level sight indicators are available
Load/unload versions feature an ergonomically curved handle that opens with a short 62 stroke.
Can be ordered with a fixed or removable handle
Chemical resistant crank seals and poppet seal (PTFE seals optional)
Any required maintenance is simplified, can be completely rebuilt without removing the valve from the tank
The ALH (anodised aluminium hard coat) nose ring can be rotated to provide a fresh cam service to
compensate for wear
API load /unload valve

PART No.

Description
5204NG
5204
5204C
5204NGC
5204SNG
5204TNG
5204NGV
Fixed handle, without sight glass, ALH nose ring, Baylast seal
Fixed handle, sight glass, ALH nose ring, Baylast seal
Removable handle*, sight glass, ALH nose ring, Baylast seal
Removable handle*, without sight glass, ALH nose ring, Baylast seal
Fixed handle, without sight glass, ALH nose ring, stainless spring for
crude oil, Baylast seal
Fixed handle, without sight glass, ALH nose ring, PTFE seals
Fixed handle, without sight glass, Viton seals
* Removable handle for Canadian market
API load only valve

PART No.
Description
5204L
5204LNG
Load only API valve with sight glass, ALH nose ring
Load only API valve without sight glass, ALH nose rings
15

API Bottom Rack Loading Fitting
Dixon API coupler uses a snap on connection where the coupling action is automatic upon contact with the API adapter.
The coupler is completely modular so it can be built with various face seal combinations to be compatible with different
alternative fuel, performance levels and applications. Two models are available: bonded nose seal and replaceable nose seal.
Material Specifications:
4 TTMA inlet mounting flange
Body: hard coated anodized AL 356 T6
5 cam design for easy alignment and tight connection
Shroud: hard coated anodized AL 356 T6, SS insert

Link, shaft, pin and crank: hardened 17-4PH stainless steel
Ball-end handle for easy, comfortable operation
Cam: CF8M stainless steel
No special tools needed for maintenance
Poppet and bearing: ZA-12
Shaft seals can be changed without removing coupler
Seal options: Baylast, Viton-B, Viton GFLT
from loading arm
Chemical Compatibility (Baylast seals):
Fully compliant with API RP1004:2003 specifications
Gasoline
Fully interlocked collar can not be opened when
Diesel
connected and can not be disconnected when opened
Avgas
One piece bonded nose seal ensures long life and
100% ethanol
cannot be washed out
100% methanol
B2 to B20 biodiesel blends
Optional replaceable nose seal for quick replacement

without removal from loading arm
Technical Specifications:
Weight: 9.1 kgs.
Maximum working pressure: 150 PSI
Peak surge pressure: 350 PSI
O
perating temperature:
Viton seals: -29C (-20F) to 204C (+400F)
Baylast seals: -29C (-20F) to 121C (+250F)
Maximum flow rate: 600 GPM
Pressure drop: 3 to 4 PSI
Chemical Compatibility (Viton-B seals):
bonded nose seal

model - 5300
Gasoline
Diesel
BOTTOM LOADING ARM API COUPLER
Jet fuel
Avgas
bonded nose
seal No.
100% ethanol
100% methanol
100% biodiesel
Any blend of the above fluids
5300
5300B
5300G
replacement
Nose seal No.

5400
5400B
5400G
SEAL MATERIAL
Baylast
Viton-B
Viton GFLT
api Dust Caps

API dust caps
PART No.

16
41450-DCAL
5000-24
5000-25
Description
Aluminium API cap with flat gasket
Aluminium API cap with O-ring gasket
Nylon API cap with flat gasket, pad lockable arm

Gravity Drop Adapters
Gravity drop adapters attach and seal directly against openable APIs and allow
Quality cast aluminium body with
drop hose with standard cam and groove couplers to clamp on and transfer
inside lip to hang on API while
petroleum from the API. Dixon manufactures two styles of gravity drop adapters:
clamping
1) standard one piece and, 2) a 2 piece bolt together design with sight glass.
Both are Dixon quality cast construction with bronze cam arms and Buna
O-Ring seals (Viton O-Rings available upon request).
Inexpensive replacement of Buna

O-Ring seal (Viton seal available)
Bronze cam arms with stainless
steel pins, finger rings
STANDARD ONE PIECE BODY

PART No.
4530
4540
41450-DCAL
31440-225AL
41440-225AL
Description
3 outlet
4 outlet
4 API Dust Cap (not shown)
3 x 4 API Offloading 10 Angle Spout, Flat gasket (not shown)
4 x 4 API Offloading 10 Angle Spout, Flat gasket (not shown)
Consists of a 4500 ring assembly and an outlet which contains mounting bolts, sight glass and seals
Customer assembly required (see sketch)
Order 4500 ring and outlets separately
TWO PIECE DESIGN WITH SIGHT GLASS

PART No.
4500
4501
4502
4503
4503SPECIAL
4504
4501ASSM
4502ASSM
4503ASSM
4504ASSM
Description
Ring only
3 Male x 4 TTMA Flange x 221/2
4 Male x 4 TTMA Flange x 221/2
4 Male x 4 TTMA Flange Straight
4 Male x 4 TTMA Flange Straight, no sight glass
4 Female x 4 TTMA Flange x 221/2 Coupler
3 Male Adapt. 221/2 x API Cplr. (4501 & 4500)
4 Male Adapt. 221/2 x API Cplr. (4502 & 4500)
4 Male Adapt. Straight x API Cplr. (4503 & 4500)
4 Female Cplr. 221/2 x API Cplr. (4504 & 4500)
Sketch illustrates assembly of 2 piece drop adapter
17

Vapour Valves
Bulb design for maximum vapour flow (low resistance) for
fast loading of tankers
Quality cast aluminium construction

4 TTMA flange
With angled acrylic sight glasses (2) and drain plug, allows
viewing and drainage of fluids if in system
With air interlock mount (use air interlock 5000AIV

if required)
PART No.
SIZE
VR4000
Features easy seal replacement while on tanker
With air interlock mount (use air interlock 5000AI

if required)
Heavy duty cast aluminium body
Available as special order without poppet (VR4100NP)
4 female NPT
PART No.
VR4100
SIZE
4
Vapour Caps
Lockable push/pull cap for vapour valves (VR4000 & VR4100) or vapour adapter (VR4086)
Aluminium cap and arms with bronze locking cam and Buna gasket
Painted orange
PART No.
VR4050AL
VR4050ALC
400-G-BU
PART No.
VR4050PL
VR4050PLC
40018BN
18
Description
Aluminium cap
Aluminium cap with chain
Replacement gasket
Description
Ultra lightweight nylon cap
Ultra lightweight nylon cap with chain
Replacement gasket

Vapour Hose Couplers
For use with vapour hose
C
ast aluminium body

Buna gasket
V
R4030CS-AL has Viton poppet seal
PART No.
description
VRC3000AL
400-CVR-AL
4030-CVR-AL
VR4030CS-AL
4030-DAVR-AL
4030-DVR-AL
400-DVR-AL
3 coupler with probe x 3 hose shank

4 coupler with poppet & probe x 3 hose shank
4 coupler with poppet & probe x 3 adapter
4 coupler with probe x 3 female NPT
4 coupler with probe x 4 female NPT
Sequential Vapour Vents

Sequential vapour vents are used for venting tank vapours during the bottom loading and unloading of petroleum tankers.
These pneumatically activated vapour vents can either be installed to open sequentially or to open independently. Vapour vents
available to suit either 16 or 20 tank manholes.
Highest flow vapour recovery vents
F
loating piston design ensures
T
ested vapour tight to 36 psi,
long life and resists poppet sticking
on the market
Baylast seals resist chemical attack from
fuel additives and alcohol
certification 49 CFR 178.345-5
C
an be used for both sequential
S
ealed system eliminates common
and non-sequential operation
leak points and improves reliability
Q
uick and easy to rebuild with
simple hand tools
PART No.
description
VR6030SQ
VR6035SQ
For 16 manhole, mounting ring attachment

For 20 manhole, 3 TTMA flange attachment
Air Interlocks
Includes 1/4 x 13/4 stainless steel
C
hoice of standard piston end or
Mounts to APIs, vapor valves and
paddle end (for bulb style vapor valve)
safety bars
Rugged solid bayloy body for dependable
service and superior corrosion resistance

PART No.
5000AI
5000AIV
5000AIR
5000AIS
5000AIST
5000S
5000ST
mounting bolts
A
djustable stroke to accommodate
length variations
description
Standard 1 button plunger pneumatic interlock
Paddle plunger pneumatic interlock, for use with VR4000 vapor valve
Roller ball plunger pneumatic interlock, ideal for use on cabinet doors
Standard 1 button plunger pneumatic interlock with electronic switch,
ideal for connecting to electronic overfill systems
1 button plunger pneumatic interlock
Electronic switch kit, for adding electronic switching to Bayco brand
pneumatic interlock valves
Replacement 1 large button
Repair kits and replacement parts available.
19

Ball Nozzles for Bulk Delivery
The Bayco brand ball nozzle uses a full port ball valve for high flow rate at a given inlet pressure.
The internal flow path is computer designed to provide low pressure drop across the nozzle.
Lower pressure drop permits higher flow rates at lower pressure, reducing foaming or backups.
Our unique swivel design permits low temperature operation without leakage around the O-ring
seals. The swivel freely rotate seven at temperatures as low as -40C (-40F) and pressures as
high as 100 PSI. Through-hardened chrome steel roller balls and hardened carbon steel ball race
provide long service life.
Standard nozzle uses a 3 PSI check valve. An optional 5 PSI check valve is available as a field
replaceable kit
Available with a field replaceable Scully compatible connector or tube spout
ball nozzles for bulk delivery

PART No.
Description
BL062
BL064
BL066
BL066NS
BL068
BL068NS
BL072
BL072NS
1143A
1125A
1 NPT swivel inlet x quick fi ll outlet

1 NPT swivel inlet x quick fi ll outlet
1 NPT swivel inlet x 1 NPT with spout
1 NPT swivel inlet x 1 NPT without spout
1 NPT swivel inlet x 1 NPT without spout
1 NPT inlet x 1 NPT without spout
1 aluminum replacement spout
1 aluminum replacement spout
Note: Nozzles also available in BSPP thread.
Swivel Nut Pipe Adapters for Ball Nozzles

Nozzle connectors are manufactured from rugged cast bronze. Short body reduces overall length of nozzle.
Interchangeable withother manufacturers. For home fuel oil delivery.
Swivel Nut Pipe Adapters for Ball Nozzles

PART No.
Description
BL002
BL001
BL005
1 male NPT
1 male NPT
fine thread
Note: Some fuel additives are not compatible with certian seal materials. Please contact the Factory for fuel
additive compatibility.
20

Trigger Nozzles - MK2
Sizes:
Standard 1 BSP Pl. inlet
Materials:
Aluminium body
Nitrile Seals
Pressure:
Maximum working pressure 60 psi / 4 bar
Details: Ideal for Diesel fuel For gravity or pumped use
trigger nozzle mk 2
PART No.
Description
DATN
DATN/MS
DATNC/MS
DATN/FS
DATNC/FS
Basic
Male Swivel Tail
With Trigger Catch
With Female Swivel Tail
With Trigger Catch
Automatic
Sizes:
Available in 3/4 BSP Pl. Female
Materials:
Aluminium
Pressure:
30 psi / 2 bar minimum working pressure
Details: For Diesel dispensing

Low flow shut down Robust, quality construction Simple lever catch
Automatic flow shut-off
automatic nozzle
PART No.
M3700
Description
Fuel dispensing nozzle
Tank Transport Equipment

Pipe Caps with 12 chain and S hook - BSPP Thread

AluminiuM
PART No.
300PCALAP
SIZE
21

Tank Transport Equipment - Intermodel
STAINLESS STEEL REDUCERS* FEMALE BSPP X MALE BSP
stainless steel*
PART No.
SIZE
3020RDSSAP
3 x 2
* PTFE gaskets standard
Gaskets & Washers

BUNa-n
PART No.
200GPCBU
300GPCBU
-
NEOPRENE
PART No.
PTFE
PART No.
150GPCTF
200GPCTF
300GPCTF
400GPCTF
KNW25
KNW35
KNW40
viton
PART No.
KVW25
KVW35
-
Grounding Stud
Solid brass, stainless steel or aluminium
With 3/8-16 UN-3A thread
For static electric grounding and overfill protection systems
PART No.
GS1
GS2
22
material
Brass
Stainless Steel
SIZE
11/2
2
3
4

FloTechTM Overfill Prevention Products
Overfill detection for road tankers is a secondary emergency shut-off system used to prevent overfilling of tanker compartments
during the terminal loading process. When an overfill situation is detected, the system will override and shut down the terminal
pump/metering equipment filling the tanker compartment(s).
The system consists of overfill sensing devices, which are electronically connected to controls at the terminal through a plug
and socket connection. Often on board tanker monitors are employed to inform on the loading process and provide diagnostic
data should a problem occur. Monitors also translate electronic signal formats for different operating systems which may
exist between the trailer and terminal. The two signal formats used are known as optic and thermistor and are defined by
API as Standard #1004. FloTech products specifications for bottom loading and are approved by FM and CSA. Products are
manufactured in accordance with EN13922.
Dixon manufactures a full line of sensors, monitors and sockets compatible with Scully and Civacon systems as well as complete
overfill kits.
23

Principals of Operation
Knowledge and Experienced Design
Dixon employees have vast experience in electronics, manufacturing
and most important, with the in-the-field trouble shooting of overfill
terminal and tanker installation. That is why we have focused on
easy, drop-in replacement features with improved probe life, and why
Dixon have included heavy duty hardware made from premium,
corrosion resistant materials.
Trouble Free Probes and Sensors:

FloTech brand probes/sensors do not use epoxy bonded prisms as a
means to seal the prism. Therefore, they are not subject to malfunction
due to epoxy/prism interface separation. FloTech brand probes/sensors
incorporate a double elastomer design which seals and secures the sensitive optic prism tip. The elastomer seals are
flexible allowing thermal expansion and resistance to steam cleaning and petroleum chemical attack.
Best in Class Technical Support

Dixon provide the most reliable overfill components and systems available on the market today. Over the years
the FloTech brand has earned a reputation for reliable overfill components compatible with other common systems.
FloTech brand items are shipped with easy to follow installation instructions and manuals.
Easy Installation
FloTech brand components are manufactured to be installed easily, even on other systems. They have been designed
to be drop-in compatible with API systems being used around the world.
Products In Stock, Delivered On Time

Dixon realise that downtime costs you money so we do everything we can to ensure you receive your parts when
you need them.
A Great Product With An Unparalleled Warranty

FloTech brand products are covered by a three year limited warranty. The warranty is part of the total system that
makes FloTech overfill detection the best choice for your operation.
24

Checkmate Retain Overfill System 2-Wire Black and White
Dixon is proud to introduce Checkmate with advanced automatic self-checking technology and performance enhancing
features not found in any other system. The FloTech Checkmate has a long list of features that greatly improve reliability
and provide years of trouble free service. Checkmate is compatible with the Scully brand black and white two-wire, overfill
and retain system. The components are drop-in replacements and compatible with the signal format required by Scully
brand on-board monitors.
FT208 Checkmate Retain / Overfill Monitors
Easy to follow programming guide for a maximum of eight compartments top only or
top and bottom service with the same monitor
Monitor can be programmed up to 100,000 times without sending it back to the factory
Monitor resists oxidation of wire connections
Stainless steel terminal blocks resist rusting of contacts
Stainless steel hardware used on all products
Powder coated colour matched components for exceptional appearance
Auxiliary input for Hobbs type switches
Power control relay output
Drop-in compatibility, see compatibility chart on at the end of this section
Factory Mutual and Canadian Standards Association approved, ATEX approval pending
Wide input power 12-24 VDC
25
FloTech brand overfill system kits provide everything needed to install a new overfill
system on your tank. One through eight compartment kits are available off the shelf.
FloTech brand kits provide everything needed to make a professional installation.
Systems include; 1 FT208 monitor, 1 FT151 sensor per compartment, 1 FT404 cable
and 1 FT402 (20pcs.) strain reliefs. Sockets sold separately.
Special length probes are available. Please refer to comparison chart for cross references
to other manufacturer model numbers.
Checkmate Overfill Systems (top only)

PART No.
Description
FT2801
FT2802
FT2803
FT2804
FT2805
FT2806
FT2807
FT2808
FT2801-12
FT2802-12
FT2803-12
FT2804-12
FT2805-12
FT2806-12
FT2807-12
FT2808-12
Checkmate, 1 compartment system (top only)

Checkmate, 1 compartment system (top only) - 12 probes
Systems include: 1 FT208 monitor, 1 FT151 overfill and FT152 retain sensor per
compartment, 1 FT404-150 cable and 1 FT403 (30 pcs.) strain reliefs. Sockets
sold separately.
Special length probes are available. Please refer to comparison chart for cross references
to other manufacturer model numbers.
Checkmate Retain / Overfill Systems (retain and overfill)

26
PART No.
Description
FT2811
FT2812
FT2813
FT2814
FT2815
FT2816
FT2817
FT2818
FT2811-12
FT2812-12
FT2813-12
FT2814-12
FT2815-12
FT2816-12
FT2817-12
FT2818-12
Checkmate, 1 compartment system (retain and overfill)

Checkmate, 1 compartment system (retain and overfill) - 12 probes

Checkmate Retain Overfill System 2-Wire Black and White
The FT150 thermo-optic 2 wire probe is electronically and mechanically compatible
for drop-in replacement of commonly used 2-wire probes with black and white wires.
The FT150 provides the fast response and reliability of optic technology in a thermistor
application. All FloTech brand probes come with a unique dual elastomer seal for prisms
and a smooth tapered tip design for easy installation without gasket damage. Custom
lengths available upon request. Compatible with the Scully Intellicheck system (probe
housing is part # FT90001)
FT150 Replacement Black and White 2-Wire Probes

PART No.
Description
FT150
FT150-12
FT150-18
FT155
Replacement probe, thermo-optic, 2 wire (black and white), 7

Dummy
The FT151 thermo-optic sensor contains the FT150 probe and a 2 NPT housing. Our probe
holder is cast aluminium with a 2 NPT mounting thread, heavy duty stainless steel hardware,
and Viton probe seal. Install in a 2 NPT female thread or 23/8 hole using the gasket and
locking nut provided. All screws and rings are heavy duty stainless steel for easy assembly
and long life. Compatible with Scully Intellicheck monitors (probe housing is part # FT9000)
AT
APPR EX
OVED
FT151 Thermo-Optic Sensors

PART No.
Description
FT151 - ATEX
FT151-12 - ATEX
FT151-18 - ATEX
Sensor, thermo-optic, 2 wire (black and white), 2 NPT housing with 7 probe
The FT152 retain sensor is a bottom retain detection sensor. The sensor has a 1/2 NPT
mounting. Sensor is shipped with a 1/2 NPT weld-on aluminium half coupling for mounting.
The main sensor portion is stainless steel to prevent galling in the trailer. The wiring box is
plastic to prevent corrosion and is removable to facilitate installation. The side ports come out
of the same side (like the overfill sensors) to make wiring easier. The FT152 is mechanically
and electrically compatible with Scully model 08819 and the Scully Intellicheck System.
AT
APPR EX
OVED
D
FT152 Retain Sensor

PART No.

Description
FT152 - ATEX
Replacement Scully retain sensor, 2 wire (black and white)
The FT208 Checkmate is compatible with the Scully brand black and white two-wire
thermo-optic (thermistor) overfill and retain system. Components are drop-in replacement and
compatible with the signal format required by the Scully Intellicheck brand on-board monitors.
Easy to follow programming guide for a maximum of eight compartments, programmable for
number of compartments, top only, top and bottom service with the same monitor.
FT208 Checkmate Retain / Overfill Monitor

PART No.

FT208
FT207
Description
Checkmate monitor, programmable for top only, or top and bottom sensors, with housing
Checkmate replacement monitor module
27

R/OM Type Retain/Overfill System Red & Black 2 Wire
These systems incorporate the preferred optic technology (red and black 2 wire) using top overfill as well as bottom
retain sensors. Retain sensors inform the terminal if the compartments are empty or if product has been retained.
Monitors include advanced diagnostic capabilities as well as translation abilities for all socket types (optic, thermistor
or float). The system offers true load at any rack compatibility.
FloTech brand overfill system kits provide everything needed to install a new API
compatible overfill system on your tank. One through six compartment kits are available
off the shelf. Systems include: 1 FT204P monitor, 1 FT202 sensor per compartment,
1 FT401 100 cable and 1 FT402 (20 pcs.) strain reliefs. Sockets sold separately.
Special length probes are available. Please refer to comparison chart for cross
references to other manufacturer model numbers.
ROM Overfill System (top only)

PART No.

FT2101
FT2102
FT2103
FT2104
FT2105
FT2106
FT2101-12
FT2102-12
FT2103-12
FT2104-12
FT2105-12
FT2106-12
Description
R/OM
R/OM
R/OM
R/OM
R/OM
R/OM
R/OM type, 1 compartment system (top only)

type, 1 compartment system (top only) - 12 probes
compatible retain/ overfill monitor top and bottom system. One through six compartment
kits are available off the shelf. Systems include: 1 FT204P monitor, 1 FT202 sensor for each
compartment, 1 FT206 retain sensor per compartment, 1 FT401 100 cable and 1 FT402
(20 pcs.) strain reliefs. Sockets sold separately. Special length probes are available.
Please refer to comparison chart for cross references to other manufacturer model numbers.
ROM Retain / Overfill Systems (retain and overfill)

28
PART No.
Description
FT2001
FT2002
FT2003
FT2004
FT2005
FT2006
FT2001-12
FT2002-12
FT2003-12
FT2004-12
FT2005-12
FT2006-12
R/OM type, 1 compartment system (retain and overfill)

R/OM type, 1 compartment system (retain and overfill) - 12 probes

The FT201 is a replacement probe for the FloTech brand FT202 sensor and is compatible
with Civacons 3150 two wire optic probe. The FloTech brand FT200 series probe uses
our unique dual elastomer seal prism design to prevent fouling. Other sensor designs
use epoxy which crack allowing fuel to leak into the optic path ultimately causing signal
malfunction. Custom lengths available upon request (probe housing is part # FT9000).
FT201 Replacement Probes

PART No.
Description
FT201
FT201-12
FT201-18
Replacement R/OM type, 2 wire (red and black) top probe, 7

The FT202 sensor is a top overfill sensor and part of the FloTech brand retain/overfill
monitoring system. The probe holder is cast aluminium with a 2 NPT mounting thread,
heavy duty stainless steel hardware, and Viton seals. The FT202 is mechanically and
electrically compatible with the Civacon model 1050 two wire top sensor. The sensor is
installed by threading it into a 2 NPT female thread or mounting it in a 23/8 hole secured
by a gasket and metal locking nut. (probe housing is part # FT9000).
FT202 Thermo-Optic Sensors
ATEX
APPR
OVED
PART No.

FT202 - ATEX
FT202-12 - ATEX
FT202-18 - ATEX
Description
Sensor R/OM type (red and black), top with 2 NPT housing, with 7 probe
The FT206 retain sensor is a bottom retain detection sensor and part of the FloTech brand
retain/ overfill monitoring system. The sensor has a 1/2 NPT mounting. Sensor comes with
a 1/2 NPT weld-on aluminium half coupling for mounting. The main sensor portion is
stainless steel to prevent galling in the trailer. The wiring box is plastic to prevent corrosion
and is removable to facilitate installation. The side ports come out of the same side (like
the overfill sensors) to make wiring easier. The FT206 is mechanically and electrically
compatible with the Civacon model 1000 two wire retain sensor.
AT
APPR EX
OVED
D
FT206 Retain Sensor

PART No.

FT206 - ATEX
Description
Retain sensor R/OM type (red and black), 1/2 NPT sensor
The FT204P retain/overfill monitor is designed to diagnose and monitor up to six

compartments. The FT204P monitor will provide API compatible optic, thermistor, and float
socket outputs for a true load at any rack compatibility. FloTechs FT203P is a replacement
chassis and is compatible with Civacon 3250 and 3252 onboard monitors.
FT204P Retain / Overfill Monitor

PART No.

FT204P
FT203P
Description
R/OM type onboard monitor, with housing
Replacement chassis, R/OM type on-board
29

API Optic System 5-Wire
FloTech series FT100 and FT101 sensors are compatible with Scully brand 5 wire optic sensors. FloTech API compatible
overfill systems feature long service life and resistance to harsh environments typical on petroleum cargo tanks. Long
service life and compatibility make FloTechTM the ideal choice for demanding cargo applications.
compatible overfill system on your tank. One through six compartment kits are available off
the shelf. Systems include: 1 FT103 monitor, 1 FT101 sensor per compartment, 1 FT400
100 cable and 1 FT402 (20 pcs.) strain reliefs. Sockets sold separately.
Optic Overfill Kits

Description
PART No.

FT1001
FT1002
FT1003
FT1004
FT1005
FT1006
FT1001-12
FT1002-12
FT1003-12
FT1004-12
FT1005-12
FT1006-12
API
API
API
API
API
API
API compatible 1 compartment system (optic)

compatible 1 compartment system (optic) - 12 probe
The FT100 replacement probe is electronically and mechanically compatible with the API
optic or 5 wire signal format. The FT100 sensor features a dual prism seal design which is
more reliable than other designs which glue in the prism using epoxies. Custom lengths are
available upon request. The FT100 is compatible with Scully #09208 and Civacon #1300.
(probe housing is part # FT9000).
FT100 REPLACEMENT PROBE

PART No.
Description
FT100
FT100-12
FT100-18
5 wire API optic probe, 7

The FT101 sensor is compatible with the API optic or 5 wire signal format. Our probe holder is
cast aluminium with a 2 NPT mounting thread, heavy duty stainless steel hardware, and Viton
seals. Install in a 2 NPT female thread or 23/8 hole using the provided gasket and locking nut.
(probe housing is part # FT9000).
AAPTPREOVXED
FT101 sensors
PART No.

FT101 - ATEX
FT101-12 - ATEX
FT101-18 - ATEX
Description
Sensor, optic, 5 wire, 2 NPT housing with 7 probe
The FT103 API compatible monitor works with the FloTech API compatible sensor models
FT101/ 100. This six channel monitor will provide API compatible optic, thermistor, and float
socket outputs for a true load at any rack compatibility. Entity approved by CSA and FM to
ensure safety. The FT102 replacement chassis is compatible with Civacon 3150 or Scully
08563 on-board monitors.
FT103 API COMPATIBLE MONITOR

PART No.

30
FT103
FT102
Description
API compatible on-board monitor, with housing
Replacement chassis, API compatible

Dummies send a permissive signal for any missing compartments. For example, in the
United States all overfill systems are formatted assuming a six compartment thermistor
trailer. Therefore, the terminal controller must receive six permissive sensor signals to allow
loading. One dummy can send up to five signals. Consequently a one to five compartment
trailer will contain one FT155 dummy (wired to socket). In Canada, where eight channel
systems are mandated, two FT155 dummies are needed with one to three compartment
trailers and one FT155 for four to seven compartments. The FloTech FT155 thermistor
dummy provides instant permissive signal in the coldest weather and is mechanically and
electrically compatible with Scully and Civacon models.
FT155 dummy
PART No.

FT155
Description
Thermistor dummy, 5 compartment
When using the FloTech trailer mounted ground ball the trailer cannot be loaded unless the
terminal ground is directly connected to the ground ball.
grounding ball
PART No.

FT451
Description
Stainless steel grounding ball
Cables are colour matched to commonly used overfill systems and have a tough, thick
outer jacket resistant to oil, UV and abrasion. For watertight cable/sensor connections
apply FloTech brand strain/relief sealing glands. Two packages are available: FT402 - 20
pieces for typical top only sensor connection systems or; FT403 - 30 pieces for typical
top and bottom sensor connection systems.
cables and glands

PART No.

FT400
FT400-1000
FT401
FT401-150
FT401-1000
FT404
FT404-150
FT404-1000
FT402
FT403
FT405-500
Description
5 conductor cable 100
5 conductor cable 1000 FT reel
7 conductor cable 1000 FT reel
11 conductor cable 1000 reel
Strain relief fittings, 1/2 NPT, 1 box = 20 pcs.
Strain relief fittings, 1/2 NPT, 1 box = 30 pcs.
Strain relief fittings, 1/2 NPT, 500 piece box
The FT520 optic test kit includes a Go, No/Go tester and test lead sets to test five wire
optic probes, two wire optic probes, and on-board monitor socket outputs. It uses the
same permissive signal verification as an optic rack monitor. Optional FT521, FT522, FT523
optic test plugs are available for an entire trailer Go, No/Go test.
Optic system tester

PART No.

FT520
FT520CASE
FT520WOGA
FT520WOGACASE
FT521
FT522
FT523
FT524
FT524-8
Description
Optic system tester
Case only for FT520
Optic system tester with FT521 test plug no test leads
Optional case for FT520 WOGA
API optic test plug with six pins and three J-slots
Optic test plug with six pins and two or four J-slots
Optic test plug J-560 type
Thermistor socket test plug (US)
Thermistor socket test plug (Canada)
31

Sockets
Sockets allow the transfer of the electronic signal from the terminal control monitor to the tanker and return. Sockets will
vary depending upon terminal equipment and regional regulations. Dixon offer a full line of sockets for all requirements.
FloTech brand sockets are mechanically and electronically compatible with the API RP1004 Rel. 2003 Bottom Loading
Specification. Optic and thermistor socket face plates are hard coated aluminium alloy to prevent J-slot wear.
All hardware and contact buttons are stainless steel to prevent corrosion. FloTech brand sockets are standard colour coded
to permit easy identification (optic sockets are blue, thermistors are green, and float are red). Coloured caps are included
for optic and thermistor models. All sockets now incorporate the patented removable nose ring.
Aluminium Hardcoat J-Slot Wear Ring
FT300 Optic Socket
FT301 Thermistor Socket
FT302 Float Socket
Overfill Prevention Sockets
PART No.
Description
FT300
FT301
FT302
FT303
FT304
FT305
FT306
FT307
FT3010
FT3011
FT3013
FT3014
FT3015
FT3016
FT3017
FT3020
FT3021
FT304BI
FT304VI
FT304BVI
Optic socket API / WOGA, 6 pin and 3 J-slots

Thermistor socket, API, 8 pin and 4 J-slots
Float, API, J560 pin type socket
Optic socket, 6 pin and 4 J-slots (U.S.)
Thermistor socket, 10 pin and 4 J-slots (Canada, Europe)
Thermistor socket, J560 pin type
Optic socket, J560 pin type
Optic socket, 6 pin and 4 J-slots (Canada)
API optic face plate assembly, 6 pin. 3-J slots
API thermistor face plate assembly, 8 pin, 4-J slots
Optic pattern contact assembly with thermistor, 6 pin, 4-J slots
Thermistor face plate assembly (Canada/Europe), 10 pin 4-J slots
Thermistor replacement face plate, J560 type
Optic replacement face plate, J560 type
Optic pattern face plate assembly (Canada), 6 pin, 4-J slots
Blue optic dust cap
Green thermistor dust cap
Socket with brake interlock
Socket with vapour recovery interlock
Socket with both brake interlock and vapour recovery interlock
Dixon offer a complete range of replacement parts for your overfill systems.
GFL series stainless steel nose rings are now available on any configuration socket that
you require. The Dixon stainless steel J-slots outlast competitor versions because they are
tougher and more corrosion resistant than any other on the market. *GFL socket J-slots are
so tough that they are Guaranteed for Life against wear. U.S. patent 6,824,423.
GFL (Guaranteed for Life*) Series Stainless Steel J-Slot Wear Ring
PART No.

32
FT300SS
FT301SS
FT303SS
FT304SS
FT307SS
FT310SS
FT311SS
FT313SS
Description

FT314SS
FT317SS
Optic socket API / WOGA, 6 pin and 3 J-slots GFL stainless wear ring
Thermistor socket, API, 8 pin and 4 J-slots GFL stainless wear ring
Optic socket, 6 pin and 4 J-slots (U.S.) GFL stainless wear ring
Thermistor socket, 10 pin and 4 J-slots (Canada, Europe) GFL stain.wear ring
Optic socket, 6 pin and 4 J-slots (Canada) GFL stainless wear ring
API optic face plate assembly, 6 pin, 3 J-slots GFL stainless wear ring
API thermistor face plate assembly, 8 pin, 4 J-slots GFL stainless wear ring
Optic pattern face plate assembly with thermistor, 6 pin, 4-J slots
GFL stainless wear ring
Thermistor face plate assembly (Canada/Europe), 10 pin, 4-J slots
Optic pattern face plate assembly (Canada), 6 pin, 4 J-slots

API Compatible Rack Cords
FT600 and FT620 are compatible with API thermistor and optic configurations
Cord available in coiled or straight lengths
Cord features a heavy highly visible safety orange jacket to meet trip hazard requirements
Cord is bonded mechanically and has superior abrasion and oil resistance
Cord sets are interchangeable with Scully and Civacon, please refer to pages 34-35 for the cross reference chart
Plug body is machined from 6061 aluminum and is color coded optic blue or thermistor green
Button contacts are made from 316 stainless steel to prevent corrosion or galling
All other hardware is stainless steel
All wiring is compatible with standard Scully color codes and wiring number configurations
The 9 pin conductor is shielded to be compatible with Scully VIP system
Model FT620 API Optic Assemblies

PART No.
FT620
FT620S
FT621
FT622
FT623
Scully
Part No.
Civacon
Part No.
Description
21831
21766
27211
08235
7120SR
7110
-
plug with 30 coiled cable

plug with 20 straight cable
replacement plug body
replacement 30 coiled cable
plug hanger
Model FT600 API Thermistor Assemblies
PART No.
Scully
Part No.
Civacon
Part No.
Description
FT600
FT600C
FT600S
FT600SC
FT601
FT601-10
FT602
FT603
FT604
21818
20769
08959
27211
-
7320
7310
-
plug with 30 coiled cable

API thermistor plug and 30 coiled cord set (Canada)
plug with 20 straight cable
plug with 20 straight cord set (Canada)
replacement plug body
replacement plug, 10 pin (Canada)
replacement 30 coiled cable
plug hanger
replacement 20 straight cord
33

Comparison Reference Chart
Listed is a cross reference between FloTech brand Drop In replacement parts and competitor products.
Replacement Parts & COMPETITOR PRODUCTS

Liquid
Level
sensors
flotech
PART No.

FT100
FT100-12
FT101
FT101-12
FT150
FT150-12
FT151
F151-12
1300
13008
1110
11108
1650
16508
1550
15508
09209
09214
09208
09213
09409
09414
09408
09413
FT152
FT155
FT201
FT201-12
FT202
FT202-12
FT205
FT206
1900
1350
13508
1050
1910
1000
08810
08542
-
flotech
PART No.
civacon
PART No.
SCULLY
PART No.
FT102
FT103
FT203P
FT204P
FT207
FT208
3150
3100
3252
3202
-
08563
88687
09100/09111
09109.09107
flotech
PART No.
civacon
PART No
SCULLY
PART No.
FT300
FT301
FT302
FT303
FT304
FT305
FT306
FT310
FT311
FT314
FT320
FT321
FT390
FT304BI
FT304VI
FT304BVI
4100
4400
4600
4200
4401
4500
4300
4110
4410
4150
4450
4401B
4401E-SQS
07974
07720
08116
07976
07716
07681
08199
21790
20770
20768
08575
08574
09060
08646I
08646P
08646IP
flotech
PART No.
civacon

PART No
SCULLY
PART No.
FT400
FT401
FT402
FT403
FT520
FT530
22056
27382
-
On BOARD
MONITORS
SOCKETS
HARDWARE
SYSTEM
TESTERS
scully
PART No.
civacon
PART No.
2100
2310
2510
-
Description
Replacement probe, optic, 5-wire, 7 long
Replacement probe, optic, 5-wire, 12 long
Sensor, optic, 5-wire, 2 NPT housing, 7 probe
Sensor, optic, 5-wire, 2 NPT housing with 12 probe
Replacement probe, thermo-optic, 7 long, 2-wire (black & white)
Replacement probe, thermo-optic, 12 long, 2-wire (black & white)
Sensor, thermo-optic, 2 NPT housing, 7 probe, 2-wire (black & white)
Sensor, thermo-optic, 2 NPT housing,12 probe, 2-wire (black &
white)
Retain sensor
Thermistor dummy, 5 compartment
Replacement R/OM type, 7 top probe, 2-wire (red & black)
Replacement R/OM type, 12 top probe, 2-wire (red & black)
Top sensor R/OM type, 2 NPT housing, 7 probe, 2-wire (red & black)
Top sensor R/OM type, 2 NPT housing, 12 probe, 2-wire(red & black)
Terminator
Retain sensor R/OM type, ? NPT sensor (red & black)
Description
Replacement chassis, API compatible

API compatible on-board monitor, with housing
Replacement chassis, R/OM type on-board monitor
R/OM type on-board monitor, with housing
Replacement module, Checkmate on-board monitor
Checkmate programmable monitor for top, or top and bottom sensors
Description
API compatible optic socket with cap (6 pin, 3 J-slots)

API compatible thermistor socket with cap (8 pin, 2/4 J-slots)
API compatible float socket
Optic pattern with thermistor J-slots, and cap (6 pin, 2/4 J-slots)
Canadian / European thermistor socket with cap (10 pin, 4 J-slots)
Thermistor socket, J560 type
Optic socket, J560 type
API optic face plate assembly with cap
API thermistor face plate assembly with cap
Canadian / European thermistor replacement face plate with cap
Blue optic dust cap
Green thermistor dust cap
EZ-Cept dual socket assembly
Socket with brake interlock
Socket with vapour recovery interlock
Socket with both brake interlock and vapour recovery interlock
Description

20 strain relief fittings, 1/2 NPT
30 strain relief fittings, 1/2 NPT
Optic system tester
T.I.M. reader
Civacon and R/OM are registered trademarks of Civacon/Dover Corp. Intellicheck is a registered trademark of Scully Signal Co.
34

Comparison Reference Chart (continued)
Listed is a cross reference between FloTech brand Drop In replacement parts and competitor products.
Replacement Parts & COMPETITOR PRODUCTS

ON board
systems
flotech
PART No.

FT1004
FT1005
FT2004
FT2005
FT2104
FT2105
FT2801
FT2802
FT2803
FT2804
FT2805
FT2806
FT2807
FT2808
FT2811
FT2812
FT2813
FT2814
FT2815
FT2816
FT2817
FT2818
scully
PART No.
civacon
PART No.

2004
2005
3024
3025
3034
3035
-
08305
08306
08251
08352
08353
08354
08355
08356
08380
08381
08361
08362
08363
08364
08365
08366
08382
08383
Description
API compatible 4 compartment system
API compatible 5 compartment system
R/OM type, 4 compartment system
R/OM type, 5 compartment system
Checkmate system, one compartment, top only
Checkmate system, two compartment, top only
Checkmate system, three compartment, top only
Checkmate system, four compartment, top only
Checkmate system, five compartment, top only
Checkmate system, six compartment, top only
Checkmate system, seven compartment, top only
Checkmate system, eight compartment, top only
Checkmate system, one compartment, top and bottom sensors
Checkmate system, two compartment, top and bottom sensors
Checkmate system, three compartment, top and bottom sensors
Checkmate system, four compartment, top and bottom sensors
Checkmate system, five compartment, top and bottom sensors
Checkmate system, six compartment, top and bottom sensors
Checkmate system, seven compartment, top and bottom sensors
Checkmate system, eight compartment, top and bottom sensors
Civacon and R/OM are registered trademarks of Civacon/Dover Corp. Intellicheck is a registered trademark of Scully Signal Co.
Dixon Valve and Coupling Company warrants the FloTech products described herein, and manufactured by Dixon to be free
from defects in material and workmanship for a period of three (3) years from date of shipment by Dixon under normal use
and service.
For further warranty information see page 57.
35

V-Ring Swivel Joints
1. Body
6. Spring retainer
2. Sleeve
7. Spring
3. Ball bearings
8. Ball retainer screw
4. Seal retainer
9. Grease fitting
5. V-Ring (pressure) seal
10. O-Ring (dust) seal
V-Ring Features
T
he spring-loaded triple V-ring sealing system ensures a leak proof seal at either high or low pressure
and an extended seal life compared to the conventional single O-ring design
T
he 3 - 8 carbon steel swivels are manufactured from a special grade of carbon steel with flame
hardened dual raceways for greater load bearing capacity and longer life
The stainless steel swivels are manufactured in 316 grade stainless steel for superior corrosion resistance.
Available with pressure ratings to 1,000 psi
Available in carbon steel, stainless steel and aluminum
Single Plane V-Ring Style 20
weld end x weld end

sizes 2 - 8
female NPT x female NPT

sizes 2 - 8
150# ASA flange x 150# ASA flange

sizes 2 - 8

sizes 2 - 8

sizes 2 - 8

sizes 2 - 8
36

sizes 2 - 8

Double Plane V-Ring Style 50

sizes 2 - 8

sizes 2 - 8

sizes 2 - 8

sizes 2 - 8

sizes 2 - 8
Triple Plane V-Ring Style 80

sizes 2 - 8

sizes 2 - 8

sizes 2 - 8
Triple Plane V-Ring Style 10

sizes 2 - 8

sizes 2 - 8
37

Typical Applications for V-Ring Swivels
Loading Arms
Floating Roof Drains
38
Floating Suction

O-Ring Swivel Joints
1. O-Ring (dust) seal
4. Grease fitting
2. Ball retainer screw
5. Ball bearings
3. O-Ring (pressure) seal
O-Ring Features
The O-ring pressure seal ensures a leak-proof seal at either high or low pressure
and smoother rotation at lower torque than multiple seal designs
Spring-loaded PTFE pressure seals are available up through 3
Carbon steel and stainless steel O-ring type swivels provide greater strength
and corrosion resistance when needed for lower torque applications
Available in carbon steel, stainless steel, aluminum, brass and iron
Single Plane O-Ring Style 20

sizes 1 - 4

sizes 1 - 4

sizes 1 - 4

sizes 1 - 4
tank truck flange x tank truck flange

sizes 2 - 4

sizes 1 - 4

sizes 1 - 4
tank truck flange x tank truck flange

sizes 2 - 4
39

Double Plane O-Ring Style 50

sizes 1 - 4

sizes 1 - 4
Double Plane O-Ring Style 60

sizes 1 - 4

sizes 1 - 4
Triple Plane O-Ring Style 70

sizes 1 - 4
40

sizes 1 - 4

Typical Applications for O-Ring Swivels
Loading Arms
Hose Loaders
* style 60 may also be found in this application
41

Dry Disconnect Couplings
When your product is:
E
xpensive
E
xpensive to clean up
E
xpensive to reprocess or dispose
H
azardous to workers or the environment
P
rone to accidental spillage and product loss
Dry Disconnect Couplings are designed for quick and spill free connection and disconnection
of hoses and pipelines. They are used by producers of ink, adhesives, fatty acids,
pharmaceuticals, liquid soaps, petroleum, chemicals, agricultural and a wide variety of common
caustic and specialty acids.
Easy to handle Push and turn - free flow, turn and pull - closed
Time savingNo need to drain hoses or pipe systems
EconomicalNo loss or spillage of liquids at connection or
disconnection
SafetyThe valve cannot be opened until the unit
is coupled
Environment friendlyAccidental spillage eliminated
Safe and reliableDue to rugged construction
SelectivityOptional selectivity for preventing contamination due to

incorrect and cross-coupling
Product lifeUncomplicated design and high quality materials ensures
longer product life
Working Pressure Aluminum:
260 psi / 18 bar
Brass/ Gunmetal: 360 psi / 25 bar
Stainless Steel:
360 psi / 25 bar
Optional SealsEPDM
Kalrez
Perlast
BR - nitrile
Chemraz
Interchanges with Avery Hardoll and Todo-matic
How it works
The principle of operation is identical for all sizes of couplings.
Closed:
Open:
Turn

and pull
Push and turn
Its released - no spillage
42
Its coupled - full flow

Dry Quick Disconnect Couplers
Hose Unit
Coupler has built-in swivel
Electrically conductive
Stainless Steel ball bearings
All wetted parts are stainless steel
Shaft journal in stainless steel embedded in PTFE to
R
ollers for the stainless steel units are Hastelloy
C276 on the stainless steel shaft
eliminate seizure
Riveted piston pin to minimise the risk for failure under
Rollers for the Aluminium and Brass units are

Aluminium-bronze on the stainless steel shaft
extreme pressure conditions

Protecting ring is weather resistant rubber
Dry Quick Disconnect Couplers x Female THREAD with Viton seals

Part NO. female ntp/bsp body size
DDC150SS
DDC200SS
DDC300SS105
DDC300SS
DDC400SS
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
DDC150AL
DDC200AL
DDC300AL105
DDC300AL
DDC400AL
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
DDC150BR
DDC200BR
DDC300GM105
DDC300GM
DDC400GM
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
Body Material
316
316
316
316
316
Stainless
Stainless
Stainless
Stainless
Stainless
Anodised
Anodised
Anodised
Anodised
Anodised
Steel
Steel
Steel
Steel
Steel
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Brass
Brass
Gunmetal
Gunmetal
Gunmetal
Composite Dust Plugs for Couplers

Part NO. size body size
DDDP150
DDDP300105
DDDP300
DDDP400
11/2 and 2
3
3
4
70mm
105mm
119mm
164mm
43

Dry Quick Disconnect Adapters
Tank Unit
T
he adapter is usually installed on the tank or manifold
Construction:
A
vailable in female NPT/BSP or 150# ASA flange
Aluminium adapter - Aluminium poppet, stainless

steel internal parts
C
onical valve seat to eliminate the risk for
Stainless Steel adapter - Stainless steel poppet,
piston blow out
stainless steel internal parts
P
TFE bearing between the piston shaft and the
piston guide to eliminate the risk for seizure
B
rass / Gunmetal adapter - Brass poppet, Brass
and stainless steel internal parts
Dry Quick Disconnect Adapters x Female THREAD with Viton seals
Part NO. female npt/bsp body size
DDA150SS
DDA200SS
DDA300SS105
DDA300SS
DDA400SS
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
DDA150AL
DDA200AL
DDA300AL105
DDA300AL
DDA400AL
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
DDA150BR
DDA200BR
DDA300GM105
DDA300GM
DDA400GM
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
Body Material
316
316
316
316
316
Stainless
Stainless
Stainless
Stainless
Stainless
Anodised
Anodised
Anodised
Anodised
Anodised
Steel
Steel
Steel
Steel
Steel
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Brass
Brass
Gunmetal
Gunmetal
Gunmetal
Dry Quick Disconnect Adapters x 150# ASA Flange with Viton seals
Part NO. female npt/bsp body size
DDA150SSFL
DDA200SSFL
DDA300SS105FL
DDA300SSFL
DDA400SSFL
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
DDA150ALFL
DDA200ALFL
DDA300AL105FL
DDA300ALFL
DDA400ALFL
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
DDA150BRFL
DDA200BRFL
DDA300GM105FL
DDA300GMFL
DDA400GMFL
11/2
2
3
3
4
70mm
70mm
105mm
119mm
164mm
Body Material
316
316
316
316
316
Stainless
Stainless
Stainless
Stainless
Stainless
Anodised
Anodised
Anodised
Anodised
Anodised
44
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Brass
Brass
Gunmetal
Gunmetal
Gunmetal
Composite Dust Caps for Adapters

Part NO. size body size
DDDC150
DDDC300105
DDDC300
DDDC400
11/2 and 2
3
3
4
Steel
Steel
Steel
Steel
Steel
70mm
105mm
119mm
164mm

Dry Break Cam and Groove Dry Disconnect Couplings
Compatible with most cam and groove style dry disconnects. The Bayco dry disconnect helps prevent spillage from
normal or accidental disconnects. A spring loaded sealing device is designed to snap closed should the valve become
disconnected with the poppet open, significantly limiting liquid loss.
Our dry disconnect couplings are available in a wide range of sizes, metals, and seal materials. Please refer to our product
description cross-reference chart for details. Special configurations can be designed for your application.
Couplers
Dry disconnect coupler has automatic closing poppet assembly
Dixon EZ Boss-Lock cam arms provide high security from

accidental opening due to vibration or snagging on 1
Heavy duty stainless steel crank and link provide long
and 2 fittings
service life
Large paddle type cam arms allow for an easy grip on
Stainless steel handle allows product exposure to corrosive
3 fittings
chemicals or washdown service

Strong handle attachment prevents bending of crank assembly
Fully interchangeable with Kamvalok (OPW trademark)
SAFETY ALERT
style fittings
Aluminum fittings have stainless steel internals*
For pressure ratings at other temperatures, contact the factory
Must be used with a DBA style adapter for coupler to operate.

Adapter sold separately.
coupler x female NPT
1 and 2 coupler x female NPT
1 and 2 coupler x female NPT
Aluminium
Part NO.
Stainless SteeL* Female

Part NO.
NPT
DBC61-150
DBC61-200
DBC61-300
DBC62-150
DBC62-200
DBC62-300
DBC63-150
DBC63-200
DBC63-300
DBC64-150
DBC64-200
DBC64-300
--DBC66-200
--------DBC69-300
DBC71-150
DBC71-200
DBC71-300
DBC72-150
DBC72-200
DBC72-300
DBC73-150
DBC73-200
DBC73-300
DBC74-150
DBC74-200
DBC74-300
DBC76-150
DBC76-200
DBC76-300
DBC77-150
DBC77-200
DBC77-300
DBC79-300
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
3
Seal
Material
Coupler
Size
2
2
4
2
2
4
2
2
4
2
2
4
2
2
4
2
2
4
4
Buna
Viton
PTFE Encapsulated
Silicone & Kalrez
EPT
Kalrez
and PTFE**
PTFE Encapsulated
Viton & Kalrez
Viton B
Max. PSI
at 70C
210
150
120
210
150
120
210
150
120
210
150
120
210
150
120
210
150
120
120
greaseless coupler x female NPT

Stainless Steel* Female

Part NO.
NPT
DBC77-150-GL
DBC77-200-GL
1
2
Coupler
Size
Seal
Material
Max. PSI
at 70C
2
2
PTFE Encapsulated Viton & Kalrez

PTFE Encapsulated Viton & Kalrez
210
150
* Stainless steel corrosion resistance is comparable to 304 stainless steel

**Kalrez gasket, main seal O-ring and handle O-ring. PTFE seals on cylinder assembly, stuffing box, and seal under poppet screw.
45
coupler x 90 swivel female NPT

Aluminum
Part NO.
DBS61-200
DBS62-200
DBS63-200
Female
NPT
Coupler
Size
Seal
Material
Max. PSI
at 70C
2
2
2
2
2
2
Buna
Viton
PTFE Encapsulated Silicone & Kalrez
150
150
150
Dust Plug for Couplers

Dust Plug for Couplers

Aluminium
Part NO.
Stainless Steel*
Part NO.
SIZE
200-DP-AL
250-DP-AL
400-DP-AL
200-DP-SS
250-DP-SS
400-DP-SS
2
2
4
Locking Kit for Couplers

Locking Kit for Couplers
46
Aluminium
Part NO.
DBCL-200
DBCL-300
Description
for use with 1 and 2 dry disconnect couplers
for use with 3 dry disconnect couplers

Adapters
Two-piece adapter design for easy rebuilding of adapters
Aluminum fittings have aluminum nose piece and brass piston
Fully interchangeable with Kamvalok (OPW trademark)
F
or pressure ratings at other temperatures, contact
style fittings
the factory
adapter x female NPT
1 and 2 adapter
3 adapter
Aluminium
Part NO.
Stainless Steel* Female

Part NO.
NPT
DBA11-150
DBA11-200
DBA11-300
DBA12-150
DBA12-200
DBA12-300
DBA63-150
DBA63-200
DBA63-300
DBA64-150
DBA64-200
DBA64-300
DBA66-150
DBA66-200
DBA66-300
------DBA69-300
DBA71-150
DBA71-200
DBA71-300
DBA72-150
DBA72-200
DBA72-300
DBA73-150
DBA73-200
DBA73-300
DBA74-150
DBA74-200
DBA74-300
DBA76-150
DBA76-200
DBA76-300
DBA77-150
DBA77-200
DBA77-300
---
2
2
4
2
2
4
2
2
4
2
2
4
2
2
4
2
2
4
4
Seal
Material
Adapter
Size
2
2
4
2
2
4
2
2
4
2
2
4
Max. PSI
at 70C
Buna
Viton
PTFE Encapsulated
Silicone
EPT
Kalrez
PTFE Encapsulated
Viton
Viton B
210
150
120
210
150
120
210
150
120
210
150
120
210
150
120
210
150
120
120
jump size adapter x female NPT

Aluminium
Part NO.
Female
NPT
Adapter
Size
Seal
Material
Max. PSI
at 70C
DBA11-1520
DBA12-1520
2
2
2
2
Buna
Viton
150
150
adapter x 150# ASA flange

Stainless Steel*
Part NO.
DBAF72-1520
DBAF73-1520
DBAF74-1520
DBAF76-1520
DBAF72-200
DBAF73-200
DBAF74-200
DBAF76-200
DBAF72-300
DBAF73-300
DBAF74-300
DBAF76-300
Flange
Size
Adapter
Size
Seal
Material
Max. PSI
at 70C
2
2
2
2
2
2
2
2
2
3
3
3
2
2
2
2
2
2
2
2
2
4
4
4
Viton
PTFE Encapsulated Silicone
EPT
Kalrez
Viton
EPT
Kalrez
Viton
EPT
Kalrez
150
150
150
150
150
150
150
150
150
120
120
120
vapor adapter x female thread

Stainless Steel*
Part NO.
DBAV73-2030
Female
NPSM
Adapter
Size
Seal
Material
Max. PSI
at 70C
PTFE
150
47

Aluminium Storz Couplings
Sizes:
1/2
Materials:
Aluminium Alloy
Optional Materials of Stainless Steel and Brass available
Pressure:
Maximum working pressure 16 bar/232 psi
Options:
Both halves of the coupling are of an identical design with no separate
to 8
male or female halves. Either half can, therefore, be connected to

any similar size of coupling. The hose coupling can be connected to
another style, e.g.: hose tail, female or male threaded and blanking
caps. It is essential that the distance between locking ears (KA) is the
same on all fittings
SUCTION COUPLINGS

PART NO. NOMINAL SIZE
2/D-25 AL
2/32-19 AL
2/32-25 AL
2/32-32 AL
2/38-38 AL
2/C-32 AL
2/C-38 AL
2/C-45 AL
2/C-52 AL
2/C-60 AL
2/65-65 AL
2/B-65 AL
2/B-70 AL
2/B-75 AL
2/B/80 AL
2/90 AL
2/100 AL
2/A-100 AL
2/A-110 AL
2/125 AL
2/135-135 AL
2/150-150 AL
2/165-150 AL
2/205 AL
96
Storz 25 (D) = DIN 14301

Storz 32
Storz 32
Storz 32
Storz 38
Storz 52 (C)
Storz 52 (C)
Storz 52 (C)
Storz 52 (C) = DIN14321
Storz 52 (C)
Storz 65
Storz 75 (B)
Storz 75 (B)
Storz 75 (B) = DIN 14322
Storz 75 (B)
Storz 90
Storz 100
Storz 110 (A)
Storz 110 (A) = DIN 14323
Storz 125
Storz 135
Storz 150 = F (3 Claws) Forged
Storz 165
Storz 205
Storz Spanner
Rubber Seals (suitable for Petrol and Oil Fluids)
48
D (mm)
KA (mm)
L (mm)
25
19
25
32
38
25
32
45
52
60
65
65
70
75
80
90
100
100
110
125
135
150
150
205
-
31
44
44
44
52
66
66
66
66
66
81
89
89
89
89
105
115
133
133
148
159
160
188
220
-
50
65
65
75
75
90
90
90
90
125
90
125
95
125
135
150
120
170
170
196
196
180
275
375
-
BSPP FEMALE THREADED ADAPTERS


DIN ISO 228

3/D-050 AL
Storz 25 (D) - DS*

3/D-075 AL
Storz 25 (D) - DS*

3/D-100 AL
Storz 25 (D) - DS* = DIN14306

3/32-100 AL
Storz 32 - DS*

3/32-125 AL
Storz 32 - DS*

3/38-150 AL
Storz 38 - DS*

3/38-200 AL
Storz 38 - DS*

3/C-100 AL
Storz 52 (C)

3/C-125 AL
Storz 52 (C)

3/C-150 AL
Storz 52 (C)

3/C-200 AL
Storz 52 C = DIN14307

3/C-250 AL
Storz 52 (C)

3/65-200 AL
Storz 65

3/65-250 AL
Storz 65

3/B-200 AL
Storz 75 (B)

3/B-250 AL
Storz 75 B = DIN 14308

3/B-300 AL
Storz 75 (B)

3/90-300 AL
Storz 90

3/100-400 AL
Storz 100 - DS*

3/A-400 AL
Storz 110 (A)

3/A-450 AL
Storz 110 A = DIN 14309

3/125-500 AL
Storz 125

3/150-600 AL
Storz 150 = F (3 Claws) Forged

3/165-600 AL
Storz 165

3/165-700 AL
Storz 165

3/205-800 AL
Storz 205

96
Storz Spanner
PIPE
THREAD
1/2
3/4
1
1
11/4
11/2
2
1
11/4
11/2
2
21/2
2
21/2
2
21/2
3
3
4
4
41/2
5
6
6
7
8
-
KA MATERIAL
(mm)
31
31
31
44
44
52
52
66
66
66
66
66
81
81
89
89
89
105
115
133
133
148
160
188
188
220
-
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
-
*DS - Suitable for both pressure and suction couplings
BSPP MALE THREADED ADAPTERS


DIN ISO 228

4/D-100 AL
Storz 25 (D) - DS*

4/D-32-100 AL
Storz 32 DS*

4/32-125 AL
Storz 32 DS*

4/38-150 AL
Storz 38 - DS*

4/C-125 AL
Storz 52 (C)

4/C-200 AL
Storz 52 (C)

4/B-250 AL
Storz 75(B)

4/B-300 AL
Storz 75(B)

4/A-400 AL
Storz 110(A)
PIPE
THREAD
1
1
11/4
11/2
11/4
2
21/2
3
4
KA MATERIAL
(mm)
31
44
44
52
66
66
89
89
133
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
49
REDUCERS STORZ - STORZ (SWIVEL)

7/C-D AL
7/B-C AL
7/A-B AL
C - D = DIN 14341
B - C = DIN 14342
A - A = DIN 14343
KA x KA (mm) MATERIAL
66/31
89/66
133/89
Aluminium Alloy
Aluminium Alloy
Aluminium Alloy
REDUCERS STORZ - STORZ (RIGID)

7/C-38 AL
7/C-32 AL
7/65-C AL
7/B-65 AL
7/90-B AL
7/100-B AL
7/A-100 AL
7/125-A AL
7/150-A
Storz C-38
Storz C-32
Storz 65-C
Storz B-65
Storz 90-B
Storz 100-B
Storz A-100
Storz 125-A
Storz 150-A
KA x KA (mm) MATERIAL
66/52
66/44
81/66
89/81
105/89
115/89
133/115
148/133
160/133
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
BLANK CAPS WITH CHAIN

KA (mm) MATERIAL
I.D. of coupling

8/D AL
8/32 AL
8/38 AL
8/C AL
8/65 AL
8/B AL
8/90 AL
8/100 AL
8/A AL
8/125 AL
8/150 AL
8/165 AL
8/205 AL
96
Storz 25 D - DS* = DIN 14310

Storz 32 DS*
Storz 38 DS*
Storz 52 C = DIN 14311
Storz 65
Storz 90
Storz 100 - DS*
Storz 110 A = DIN 14313
Storz 125
Storz 150 = F (3 Claws) forged
Storz 165
Storz 205
Storz Spanner
50
31
44
52
66
81
89
105
115
133
148
160
188
220
-
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
Aluminium
-
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
Alloy
DELIVERY-SUCTION SEALS

PART NO.
NOMINAL SIZE
69/D PB
69/32 PB
69/38 PB
69/CPB
69/65 PB
69/BPB
69/90 PB
69/100 PB
69/A PB
69/125 PB
Storz 25 D* = DIN 14301

Storz 32 - DS*
Storz 38 - DS*
Storz 52 C = DIN 14311
Storz 65
Storz 90
Storz 100 - DS*
Storz 110 A = DIN 14313
Storz 125
*DS - Suitable for both pressure & suction couplings.

Food quality material available on request.
51

Tank Wagon Couplings BS EN 14420-6:2004
STAINLESS STEEL TANKWAGON COUPLINGS

PART NO.
SIZE MATERIAL

MK50SS
MK80SS
MK100SS

VK50SS

VK80SS

VK100SS
DN50
DN80
DN100
Stainless Steel
Stainless Steel
Stainless Steel
DN50
DN80
DN100
Stainless Steel
Stainless Steel
Stainless Steel

VB50SS

VB80SS

MB50SS
MB80SS
DN50
DN80
Stainless Steel
Stainless Steel
DN50
DN80
Stainless Steel
Stainless Steel
FORGED BRASS TANKWAGON COUPLINGS

PART NO.
SIZE MATERIAL

MK50BR
MK80BR
MK100BR

VK50BR

VK80BR

VK100BR
52
DN50
DN80
DN100
Forged Brass
Forged Brass
Forged Brass
DN50
DN80
DN100
Forged Brass
Forged Brass
Forged Brass

Tank Wagon Spares & Seals BS EN 14420-6:2004
STAINLESS STEEL TANKWAGON SPARE PARTS

PART NO.
SIZE

DESCRIPTION
MKLR 50SS

MKLR 80SS

MKLR 100SS
DN50
DN80
DN100
Locking Ring
Locking Ring
Locking Ring
MKSR 50SS
MKSR 80SS
MKSR 100SS
DN50
DN80
DN100
Sealing Ring Section

FORGED BRASS TANKWAGON SPARE PARTS

PART NO.
SIZE

DESCRIPTION
MKLR50BR

MKLR80BR

MKLR100BR
DN50
DN80
DN100
Locking Ring
Locking Ring
Locking Ring
MKSR50BR
MKSR80BR
MKSR100BR
DN50
DN80
DN100

SEALS AND GASKETS FOR TANKWAGON COUPLINGS

PART NO.
SIZE

MBG50

MBG80

MBG100
DESCRIPTION
DN50
DN80
DN100
Female Blanking Gasket

TWHS50
TWHS80
TWHS100
DN50
DN80
DN100
Hypalon Seal
Hypalon Seal
Hypalon Seal
TS 50T
TS 80T
TS 100T
DN50
DN80
DN100
PTFE Thread Seal

PTFE Thread Seal
PTFE Thread Seal
53

Our range of low pressure tank equipment is designed to meet the stringent requirements specified for the safe storage of
volatile liquids and gasses.
All our products are designed to offer both practical and cost effective solutions in such diverse industries as
Petrochemical, Tank storage, Pharmaceutical, Chemical and Oil & Gas. All industries where safety is paramount.
Products
B100 - Combined Pressure and Vacuum Relief Valves
The B100 Series ensures that tanks and vessels are kept safe during periods of excessive
pressure and vacuum caused by filling and emptying of product and changes in temperature
due to climatic or external fire sources. Available as vent to atmosphere and piped
away version.
B200 - Vacuum Relief Valves

vacuum caused by emptying of product and changes in temperature due to climatic
changes. Conventional and side mounting options available.
B300 - Pressure Relief Valves

pressure caused by filling of product and changes in temperature due to climatic or external
fire sources. Available as vent to atmosphere and piped away units with the piped away unit
also capable of operating as a vacuum relief valve.
B400 - Emergency Relief Valves

pressure due to external fire sources and also allows access to the tank for inspection /
cleaning purposes.
B500 - Gauge Hatches

The B500 Series are designed to provide access to tanks or vessels for sampling,
measurement and inspection. Options include self closing, clamp down and lockable.
FOR INFORMATION ON ANY OF THESE PRODUCTS PLEASE DO NOT HESITATE TO CONTACT OUR SALES DEPARTMENT
54

Index
Page #
Page No.
FloTech Comparison Chart
34-35
FloTech Overfill Prevention
23-35
Replacement Probes
A
Air Interlock
S
G
19
Air Relief Valves
6-7
Sequential Vapour Vents
Gaskets
22
Sockets
API Bottom Rack Loading
16
Gravity Drop Adapter
17
Storz
API Compatible Rack Cord
33
Grounding Ball
31
Swing Check Valves
API Dust Cap
16
Grounding Studs
22
Swivel Joints
API Optic System
23-31
19
32
48-51
8-10
36-41
30-31
API Valves
15
ATEX
27-31
Horizontal Swing Check Valve
20
Butterfly Valves
In Line Sight Glass
11-13
C
Checkmate Retain Overfill System
Dry Break Cam & Groove
42-47
Dry Bulk Tanker Products
5-13
E
EN 14420-6:2004 Tank Wagon
Couplings
Optic Sensor Tester
31
Overfill Prevention Socket
32
42-47
23-31
Pneuclean
21
52-53
V
6-7
Vapour Caps
18
Vapour Hose Coupler
19
Vapour Valve
18
P
27, 29
Trigger Nozzles
Vacuum Relief Valves
Overfill System
Thermo Optic Sensor
54
52-53
57
TW Couplings
25-27
Dry Disconnect Couplings & Adapters
10
Tank Wagen Couplings

Terms & Conditions
B
Ball Nozzles
T
10
14-22
Warranty
57
52-53
R
F
Filtration Systems
R/OM Type Retain Overfill System

7
Rack Cord
28-29
33
55

Alphabetical Part Number Index
In the following Index, a is used to represent a variable.
Part No
Page
DDASS
44
FT20P
29
FT600
33
A2180/XX
DDASSFL
44
FT200
28
FT601
33
A2182/XX
DDCAL
43
FT200-12
28
FT62
33
A3180/XX
DDCBR
43
FT201
29
GS
22
54
DDCGM
43
FT201-12
29
KNW
22
BL00
20
DDCSS
43
FT201-18
29
KVW
22
BL06
20
DDDC
44
FT210
28
M3700
21
BL07
20
DDDP
43
FT210-12
28
MBSS
52
DATN/FS
21
FT-12-ATEX
27
FT280
26
MKSS
52
DATN/MS
21
FT-15-ATEX
27
FT280-12
26
MKSS
52
DATNC/FS
21
FT-ATEX
27
FT281
26
MKLRBR
53
DATNC/MS
21
FT10
30
FT281-12
26
MKLRSS
53
DBA-
47
FT100
30
FT3SS
32
MKSR
53
DBAF-
47
FT100
30
FT30
32
MKSRSS
53
DBAV73-2030
47
FT100-12
30
FT304 BI
32
PC500
DBC-
45
FT100-12
30
FT304 BVI
32
SWCV
10
DBC77--GL
45
FT100-18
30
FT304 VI
32
VBSS
52
DBCL-
46
FT101 - ATEX
30
FT40
31
VKSS
52
DBS6-200
46
FT101-12 - ATEX
30
FT40-1000
31
VKSS
52
DDAAL
44
FT101-18 - ATEX
30
FT40-150
31
VR4
18
DDAALFL
44
FT150
27
FT40-500
31
VR4PL
18
DDABR
44
FT150-
27
FT451
31
VR60SQ
19
DDABRFL
44
FT155
27
FT52
31
VRC3000AL
19
DDAGM
44
FT155
31
FT52-8
31
DDAGMFL
44
FT20
27
FT520
31
1143A
20
3090
4540
17
Numerical Part Number Index

In the following Index, a is used to represent a variable.
Part No
-CVR-AL
19
2/- AL
48
31440-225AL
17
5000 AI
19
-DP-AL
46
206--5
13
35AA
10
5000 AIR
19
-DP-SS
46
2180B/15
35CA
10
5000 AIS
19
-DVR-AL
19
2180V/15
35CC
10
5000 AIV
19
GPCBU
22
2182B/XX
4/- AL
49
5000 S
19
GPCTF
22
2182F/XX
40018BN
18
5000 ST
19
--400-99-BPKIT
13
2182V/XX
400-206-65
13
5000-
16
/ AL
50
3/- AL
400-G-BU
18
5204
15
5300
16
-390-
12-13
49
3000
4040
-390-209U
12
3000TE
41440-225AL
17
69/ PB
51
-390-828U501
12
3001
41450-DCAL
16
6-99-400BPKIT
13
-400-
11
300PCALAP
450
17
7/- AL
50
-400-
1125A
56
Page
21
12-13
3020
450ASSM
17
7/- AL
50
20
3030
4530
17
96
48

Dixon Terms & Conditions
Limited Warranty
Dixon Group Europe Ltd (herein called Dixon) warrants the products described herein, and manufactured by Dixon to be
free from defects in material and workmanship for a period of one (1) year from date of shipment by Dixon under normal
use and service. Its sole obligation under this warranty being limited to repairing or replacing, as hereinafter provided, at its
option any product found to Dixons satisfaction to be defective upon examination by it, provided that such product shall
be returned for inspection to Dixons factory within three (3) months after discovery of the defect. The repair or replacement
of defective products will be made without charge for parts or labour. This warranty shall not apply to: (a) parts or products
not manufactured by Dixon, the warranty of such items being limited to the actual warranty extended to Dixon by its
supplier; (b) any product that has been subject to abuse, negligence, accident, or misapplication; (c) any product altered
or repaired by others than Dixon; and (d) to normal maintenance services and the replacement of service items (such as
washers, gaskets and lubricants) made in connection with such services. To the extent permitted by United Kingdom
law, this limited warranty shall extend only to the buyer and any other person reasonably expected to use or consume
the goods who is injured in person by any breach of the warranty. No action may be brought against Dixon for an alleged
breach of warranty unless such action is instituted within one (1) year from the date the cause of action accrues. This
limited warranty shall be construed and enforced to the fullest extent allowable by applicable United Kingdom law.
OTHER THAN THE OBLIGATION OF DIXON SET FORTH HEREIN, DIXON DISCLAIMS ALL WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, AND ANY OTHER OBLIGATION OR LIABILITY. THE FOREGOING
CONSTITUTES DIXONS SOLE OBLIGATION WITH RESPECT TO DAMAGES, WHETHER DIRECT, INCIDENTAL OR
CONSEQUENTIAL, RESULTING FROM THE USE OR PERFORMANCE OF THE PRODUCT.
Some products and sizes may be discontinued when stock is depleted, or may require a minimum quantity for ordering.
Dixon Group Europe Ltd is committed to a policy of continuous development, and as such, the above detailed specification
and may be subject to change without notice. Dixon Group Europe Ltd reserves the right to change and modify designs
and specification without notice.
Pricing
Dixon will always try to maintain pricing, however, with the fluctuation of material cost we may be forced to change prices.
Please be aware pricing is subject to change without notice.
Freight/Postage & Carriage Charges

Postage & carriage charges are at the customers expense and will be charged at current appropriate rates.
Returns
Dixon will allow its customers to return any product for any reason within 30 days of shipment, provided it is received in a
saleable condition. The customer must call to receive a CCR number prior to returning goods to Dixon and shipping will be
at the customers expense, unless it is determined Dixon created the reason for the return.
A re-stocking charge of 25% applies to all returns.
Limits of Liability
This catalogue is intended as a product offering. It is not intended to be a user or technical manual. Information in this
catalogue is subject to change without notice. All users and distributors of products sold through this catalogue should
contact Dixon with questions of use, compatibilitys, coupling procedures and life of product. Dixons full time engineering
and test staff is always available to recommend uses and to assist distributors and users with questions.
Copyright
Copyright 2012 by Dixon Group Europe Ltd.
All rights reserved. This book is copyrighted material. Use, reproduction or copying of it by anyone other than Dixon is
strictly forbidden without its express written consent.
57

Notes
58

Notes
59
Dixon Europe
Dixon Deutschland GmbH
Godesberger Strasse 20b
D 53842 Troisdorf Spich
Germany
Tel: +49 (0)2241 844 060
Email: [email protected]
Dixon Middle East

Executive Suite,
PO Box 121599,
Saif Zone-Sharjah,
United Arab Emirates
Dixon Russia
22/2 A Sadovaya Street
Office 27-H
Saint Petersburg
Russia
Tel: +7 (812) 677 54 47
Dixon France
105 Route Pommiers
UBIDOCA Center, 5837
F-74370 Saint Martin Bellevue
France
Dixon Worldwide
Dixon Valve & Coupling Co
800 High Street
Chestertown
MD 21620
USA
Tel: +1 410 778 2000
Dixon Shanghai
Room 801-803
No.3553 North Zhongshan Rd
Putuo District
Shanghai, China
Tel: +86 21 6173 7998
Dixon Asia Pacific

PO Box 2491
Regency Park
SA 5942
Australia
Tel: +61 8 8202 6000
Dixon India
90, Virwani Industrial Estate,
Western Express Highway,
Goregaon East,
Mumbai 400 063, India
Tel: +91-22-61949494 / 29271152
Dixon Group Europe Limited

Dixon House, 350 Leach Place,
Walton Summit Centre, Preston PR5 8AS, UK.
Telephone: +44 (0)1772 323529
Fax: +44 (0)1772 314664
www.dixoneurope.co.uk / www.dixoneurope.eu
Stay connected with Dixon on
or
www.youtube.com/user/DixonValve
Customer Service: +44 (0)1772 323529
2012 DGEL
Printed in the UK
TANKCAT01

Tanker

Uploaded by

Copyright:

Available Formats

Tanker

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tanker

Uploaded by

Copyright:

Available Formats

CUSTOMER SERVICE INNOVATION MANUFACTURING QUALITY TECHNICAL EXPERTISE EXCELLENCE DESIGN

Tanker & Overfill

Customer Service: +44 (0)1772 323529

Telephone: +44 (0)1772 323529

Fax: +44 (0)1772 314664

Tanker & Overfill

Telephone: +44 (0)1772 323529

Fax: +44 (0)1772 314664

Tanker & Overfill Prevention Products

Dry Bulk Tanker Products

Petroleum Tanker Products

Low Pressure Tank Equipment

Air Relief Valves.

API Valves / Drop Adapters.

Vacuum Relief Valves.

Vacuum Relief Valves.

Vapour Valves, Couplers & Caps.

Pressure Relief Valves.

Caps, Adapters and Reducers.

Vapour Elbows & Air Interlocks.

Combined Pressure and Vacuum.

Shut off and pressure Nozzles.

Emergency Relief Valves.

Swing Check Valves.

Flanged Sight Flow Indicators.

Pipe Caps & Reducers.

Tanker & Overfill Prevention Products

Air and Vacuum Relief Valves

Butterfly Valves and Hopper Tees

Tanker & Overfill Prevention Products

A2180 up to 500 SCFM

A2182 up to 1400 SCFM

A3180 up to 1300 SCFM

Tamper proof stainless steel cup seals

Suitable for high temperature (to 200C) and food

Model 2182 has Silicon rubber poppet which

reduces tendency to cake cement, lime etc

Designed for trailer service

Shown with optional Safety Lanyard

Shown with optional Safety Lanyard

Tanker & Overfill Prevention Products

Pneuclean Pneumatic Filtration System

4 inlet (can be converted

4 outlet (can be converted to 3

replacement parts Description

4 Pneuclean complete housing with filter

In-Line High Pressure Air Filtration for 4 Air Lines

Average 12 month filter cartridge lifespan

Maximum air flow 1000 CFMs

Quick release V-clamp for easy inspection

Back pressure only .05 psi

Overall weight 26 lbs (11.8kg)

Temperature range -45 to 230C

Tanker & Overfill Prevention Products

Easy maintenance inspection lid

Drop in flapper assembly

Captive springs and shaft to prevent contamination

High temperature white food grade seal

Stainless Steel hardware

SWING CHECK VALVES

Tamper proof stainless steel cup seals

Suitable for high temperature (to 200C) and food

Model 2182 has Silicon rubber poppet which

Average 12 month filter cartridge lifespan

Maximum air flow 1000 CFMs

Quick release V-clamp for easy inspection

Back pressure only .05 psi

Overall weight 26 lbs (11.8kg)

Temperature range -45 to 230C

A positive seating disc allows flow only in one

4 TTMA inlet mounting flange

5 cam design for easy alignment and tight connection

Ball-end handle for easy, comfortable operation

No special tools needed for maintenance

Shaft seals can be changed without removing coupler

Fully compliant with API RP1004:2003 specifications

Fully interlocked collar can not be opened when

One piece bonded nose seal ensures long life and

Optional replaceable nose seal for quick replacement

Quality cast aluminium body with

Inexpensive replacement of Buna