EasyGen 2000 Configuration Manual 37427 PDF

37427
easYgen-2000 Series
Genset Control
Configuration
Software Version 1.xxxx
Manual 37427
Manual 37427
easYgen-2000 Series - Genset Control
WARNING
Read this entire manual and all other publications pertaining to the work to be performed before
installing, operating, or servicing this equipment. Practice all plant and safety instructions and
precautions. Failure to follow instructions can cause personal injury and/or property damage.
The engine, turbine, or other type of prime mover should be equipped with an overspeed
(overtemperature, or overpressure, where applicable) shutdown device(s), that operates totally
independently of the prime mover control device(s) to protect against runaway or damage to the
engine, turbine, or other type of prime mover with possible personal injury or loss of life should the
mechanical-hydraulic governor(s) or electric control(s), the actuator(s), fuel control(s), the driving
mechanism(s), the linkage(s), or the controlled device(s) fail.
Any unauthorized modifications to or use of this equipment outside its specified mechanical, electrical,
or other operating limits may cause personal injury and/or property damage, including damage to the
equipment. Any such unauthorized modifications: (i) constitute "misuse" and/or "negligence" within
the meaning of the product warranty thereby excluding warranty coverage for any resulting damage,
and (ii) invalidate product certifications or listings.
CAUTION
To prevent damage to a control system that uses an alternator or battery-charging device, make sure
the charging device is turned off before disconnecting the battery from the system.
Electronic controls contain static-sensitive parts. Observe the following precautions to prevent
damage to these parts.
Discharge body static before handling the control (with power to the control turned off, contact a
grounded surface and maintain contact while handling the control).
Avoid all plastic, vinyl, and Styrofoam (except antistatic versions) around printed circuit boards.
Do not touch the components or conductors on a printed circuit board with your hands or with
conductive devices.
OUT-OF-DATE PUBLICATION
This publication may have been revised or updated since this copy was produced. To verify that you
have the latest revision, be sure to check the Woodward website:
http://www.woodward.com/pubs/current.pdf
The revision level is shown at the bottom of the front cover after the publication number. The latest
version of most publications is available at:
http://www.woodward.com/publications
If your publication is not there, please contact your customer service representative to get the latest
copy.
Important definitions
WARNING
Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation that, if not avoided, could result in damage to equipment.
NOTE
Provides other helpful information that does not fall under the warning or caution categories.
Woodward reserves the right to update any portion of this publication at any time. Information provided by Woodward is believed to be
correct and reliable. However, Woodward assumes no responsibility unless otherwise expressly undertaken.
Woodward
All Rights Reserved.
Page 2/339
Woodward
Manual 37427
Revision History
Rev. Date
NEW 09-06-09
Editor
TE
Changes
Release
Content
CHAPTER 1. GENERAL INFORMATION ..................................................................................... 11
Document Overview ............................................................................................................................... 11
Abbreviations ......................................................................................................................................... 12
CHAPTER 2. CONFIGURATION ................................................................................................ 13

Configuration Via The Front Panel ......................................................................................................... 13
Configuration Using The PC .................................................................................................................. 14
Install ToolKit Configuration and Visualization Software ............................................................... 14
Configure ToolKit ........................................................................................................................... 15
ToolKit Files ................................................................................................................................... 16
Language-Dependent SID Files ...............................................................................................................17

SID Files for Using ToolKit on the CAN Bus With Other CANopen Devices.............................................17
Loading WSET Files of Previous Revisions .............................................................................................17
Connect ToolKit and the easYgen Unit ......................................................................................... 18

View easYgen Data with ToolKit ................................................................................................... 19
Configure the easYgen with ToolKit .............................................................................................. 20
The Settings File Function of ToolKit ............................................................................................ 20
Function of the Inputs and Outputs ........................................................................................................ 21
CHAPTER 3. PARAMETERS..................................................................................................... 25
Configure Language / Clock................................................................................................................... 26
Configure Display ................................................................................................................................... 29
Lamp Test .............................................................................................................................................. 29
Enter Password ...................................................................................................................................... 30
System Management ............................................................................................................................. 32
System Management: Password System ..................................................................................... 34
Configuration .......................................................................................................................................... 35
Configure Measurement......................................................................................................................... 36
Configure Measurement: Configure Transformer ......................................................................... 42
Generator .................................................................................................................................................42
Busbar ......................................................................................................................................................44
Mains PT ..................................................................................................................................................45
Mains Current Transformer ......................................................................................................................45
Ground Current Transformer ....................................................................................................................46
Woodward
Page 3/339
Manual 37427
Configure Monitoring ............................................................................................................................. 47

Configure Monitoring: Generator .................................................................................................. 47
Configure Monitoring: Generator, Operating Voltage / Frequency ........................................................... 48

Configure Monitoring: Generator, Overfrequency (Levels 1 & 2) ANSI# 81O .......................................... 49
Configure Monitoring: Generator, Underfrequency (Levels 1 & 2) ANSI# 81U ........................................ 51
Configure Monitoring: Generator, Overvoltage (Levels 1 & 2) ANSI# 59 ................................................. 53
Configure Monitoring: Generator, Undervoltage (Levels 1 & 2) ANSI# 27 ............................................... 55
Configure Monitoring: Generator, Time-Overcurrent Monit. (Levels 1, 2 & 3) ANSI# 50/51..................... 57
Configure Monitoring: Generator, Reverse/Reduced Power (Levels 1 & 2) ANSI# 32R/F ....................... 59
Configure Monitoring: Generator, Overload IOP (Levels 1 & 2) ANSI# 32............................................... 61
Configure Monitoring: Generator, Overload MOP (Levels 1 & 2) ANSI# 32............................................. 63
Configure Monitoring: Generator, Unbalanced Load (Levels 1 & 2) ANSI# 46 ........................................ 65
Configure Monitoring: Generator, Voltage Asymmetry............................................................................. 68
Configure Monitoring: Generator, Ground Fault (Levels 1 & 2) ................................................................ 70
Configure Monitoring: Generator, Phase Rotation ................................................................................... 73
Configure Monitoring: Generator, Inverse Time-Overcurrent Monitoring ANSI# IEC 255 ........................ 75
Configure Monitoring: Generator, Lagging Power Factor Monitoring (Levels 1 & 2) ................................ 79
Configure Monitoring: Generator, Leading Power Factor Monitoring (Levels 1 & 2) ................................ 81
Configure Monitoring: Mains ......................................................................................................... 83
Configure Monitoring: Mains, Operating Voltage / Frequency ................................................................. 83

Configure Monitoring: Mains, Decoupling ................................................................................................ 85
Configure Monitoring: Mains, Overfrequency (Levels 1 & 2) ANSI# 81O................................................. 87
Configure Monitoring: Mains, Underfrequency (Levels 1 & 2) ANSI# 81U ............................................... 89
Configure Monitoring: Mains, Overvoltage (Levels 1 & 2) ANSI# 59........................................................ 91
Configure Monitoring: Mains, Undervoltage (Levels 1 & 2) ANSI# 27...................................................... 93
Configure Monitoring: Mains, Phase Shift ................................................................................................ 95
Configure Monitoring: Mains, Voltage Phase Rotation - {2oc} ................................................................. 98
Configure Monitoring: Engine ..................................................................................................... 100
Configure Monitoring: Engine, Overspeed (Levels 1 & 2) ANSI# 12 ...................................................... 100

Configure Monitoring: Engine, Underspeed (Levels 1 & 2) .................................................................... 102
Configure Monitoring: Engine/Generator, Speed Detection (Speed/Frequency Mismatch) ................... 104
Configure Monitoring: Engine, Generator Active Power Mismatch ........................................................ 106
Configure Monitoring: Engine, Mains Active Power Mismatch ............................................................... 107
Configure Monitoring: Engine, Generator Unloading Mismatch ............................................................. 108
Configure Monitoring: Engine, Start Failure ........................................................................................... 109
Configure Monitoring: Engine, Shutdown Malfunction ........................................................................... 110
Configure Monitoring: Engine, Unintended Stop .................................................................................... 111
Configure Monitoring: Engine, Operating Range Failure ....................................................................... 112
Configure Monitoring: Engine, Charge Alternator (D+) .......................................................................... 113
Configure Monitoring: Breaker Monitoring .................................................................................. 114
Configure GCB....................................................................................................................................... 114

Configure Synchronization GCB ............................................................................................................ 115
Configure MCB {2oc} ............................................................................................................................. 116
Configure Synchronization MCB ............................................................................................................ 118
Configure Monitoring: Breakers, Generator / Busbar / Mains Phase Rotation - {2oc} ............................ 119
Configure Monitoring: Flexible Limits .......................................................................................... 120

Configure Monitoring: Miscellaneous .......................................................................................... 124
Configure Monitoring: Miscellaneous, Alarm Acknowledgement ........................................................... 124

Configure Monitoring: Miscellaneous, Configure CAN bus overload...................................................... 125
Configure Monitoring: Miscellaneous, Configure CAN Interface 1 ......................................................... 126
Configure Monitoring: Miscellaneous, Configure CAN Interface 2 ......................................................... 127
Configure Monitoring: Miscellaneous, Configure CAN Interface 2, J1939 Interface............................... 128
Configure Monitoring: Miscellaneous, Battery, Overvoltage (Levels 1 & 2) ........................................... 131
Configure Monitoring: Miscellaneous, Battery, Undervoltage (Levels 1 & 2) ......................................... 133
Configure Monitoring: Miscellaneous, Multi-Unit Parameter Alignment ................................................. 135
Configure Monitoring: Miscellaneous, Multi-Unit Missing Members ....................................................... 137
Configure Application........................................................................................................................... 138

Configure Application: Configure Breakers................................................................................. 138
Operation Of The Circuit Breakers ......................................................................................................... 140

Configure Application: Configure Breakers, Dead Bus Detection Limit .................................................. 148
Configure Application: Configure Breakers, GCB .................................................................................. 149
Configure Application: Configure Breakers, MCB .................................................................................. 153
Configure Application: Configure Breakers, Synchronization ................................................................. 155
Page 4/339
Woodward
Manual 37427
Configure Application: Configure Inputs and Outputs ................................................................. 156
Configure Analog Inputs (FlexIn) ............................................................................................................156

Configure Discrete Inputs .......................................................................................................................166
Configure External Discrete Inputs .........................................................................................................169
Discrete Outputs (LogicsManager) .........................................................................................................170
External Discrete Outputs (LogicsManager) ...........................................................................................171
Configure Analog Outputs ......................................................................................................................171
Configure Application: Configure Engine .................................................................................... 176
Configure Application: Configure Engine, Engine Type ..........................................................................176

Configure Application: Configure Engine, Start/Stop ..............................................................................182
Configure Application: Configure Engine, MPU ......................................................................................187
Configure Application: Configure Engine, Idle Mode ..............................................................................188
Configure Application: Configure Emergency Run...................................................................... 189

Configure Application: Configure Automatic Run ........................................................................ 191
Configure Application: Automatic, Start In AUTOMATIC Operating Mode (LogicsManager) .................191

Configure Application: Automatic, Stop In AUTOMATIC Operating Mode (LogicsManager) ..................192
Configure Application: Automatic, Load-Dependent Start/Stop (LDSS) .................................................193
Configure Application: Automatic, Start w/o Load (LogicsManager).......................................................209
Configure Application: Automatic, Operation Modes ..............................................................................209
Configure Application: Automatic, Critical Mode (Sprinkler Operation, LogicsManager) ........................210
Configure Application: Configure Controller ................................................................................ 215
Overview ................................................................................................................................................215
PID Tuning Example ..............................................................................................................................216
Configure Application: Controller, Frequency Control ............................................................................217
Configure Application: Controller, Load Control .....................................................................................223
Configure Application: Controller, Voltage Control .................................................................................229
Configure Application: Controller, Power Factor Control ........................................................................234
Configure Application: Controller, Load Share Control ...........................................................................238
Configure Application: Controller, Discrete Raise/Low/Function ............................................................245
Configure Interfaces ............................................................................................................................. 246

Configure Interfaces: Configure CAN Interfaces (FlexCAN) ....................................................... 246
Configure CAN Interface 1 .....................................................................................................................246

Configure CAN Interface 2 .....................................................................................................................255
Load Share Parameters .........................................................................................................................260
Configure Interfaces: Configure RS-232 Interfaces .................................................................... 261
Configure Serial Interface 1 ....................................................................................................................261
Configure Interfaces: Configure RS-485 Interfaces .................................................................... 262
Configure Serial Interface 2 ....................................................................................................................262
Configure LogicsManager .................................................................................................................... 263

Configure LogicsManager: Configure Internal Flags................................................................... 263
Configure LogicsManager: Set Timer.......................................................................................... 264
LogicsManager: Daily Time Set Point ....................................................................................................264

LogicsManager: Active Time Set Point ...................................................................................................264
LogicsManager: Weekly Time Set Point .................................................................................................265
Configure Counters .............................................................................................................................. 266

Configure Counters: Maintenance Call ....................................................................................... 266
Configure Counters: Operation Hours, kWh, and kvarh.............................................................. 267
Configure Counters: Start Counter .............................................................................................. 268
APPENDIX A. MISCELLANEOUS ............................................................................................ 269
Alarm Classes ...................................................................................................................................... 269

Conversion Factors .............................................................................................................................. 270
Temperature ................................................................................................................................ 270
Pressure ...................................................................................................................................... 270
Woodward
Page 5/339
Manual 37427
APPENDIX B. LOGICSMANAGER ........................................................................................... 271
Structure and Description of the LogicsManager ................................................................................... 271

Configuration of the Command Chain .................................................................................................... 272
Logical Symbols ................................................................................................................................... 272

Logical Outputs .................................................................................................................................... 273
Logical Outputs: Internal Flags ................................................................................................... 273
Logical Outputs: Internal Functions ............................................................................................ 274
Priority Hierarchy of the Logical Outputs .................................................................................... 275
Logical Outputs: Relay Outputs .................................................................................................. 276
Logical Command Variables ................................................................................................................ 277
Logical Command Variables: Group 00: Flags Condition 1 ........................................................ 278
Logical Command Variables: Group 01: Alarm System ............................................................. 280
Logical Command Variables: Group 02: Systems Condition ...................................................... 281
Logical Command Variables: Group 03: Engine Control ............................................................ 282
Logical Command Variables: Group 04: Applications Condition ................................................ 283
Logical Command Variables: Group 05: Engine Related Alarms ............................................... 284
Logical Command Variables: Group 06: Generator Related Alarms .......................................... 285
Logical Command Variables: Group 07: Mains Related Alarms ................................................ 286
Logical Command Variables: Group 08: System Related Alarms .............................................. 286
Logical Command Variables: Group 09: Discrete Inputs ............................................................ 287
Logical Command Variables: Group 10: Analog Inputs .............................................................. 287
Logical Command Variables: Group 11: Clock and Timer ......................................................... 287
Logical Command Variables: Group 12: External Discrete Inputs 1 .......................................... 288
Logical Command Variables: Group 13: Discrete Outputs ......................................................... 288
Logical Command Variables: Group 14: External Discrete Outputs 1 ........................................ 289
Logical Command Variables: Group 15: Flexible Limits ............................................................. 289
Logical Command Variables: Group 18: Transistor Outputs ...................................................... 289
Factory Setting ..................................................................................................................................... 290
Factory Setting: Functions .......................................................................................................... 290
Factory Setting: Relay Outputs ................................................................................................... 300
Discrete Inputs ............................................................................................................................ 304
APPENDIX C. ANALOG MANAGER ......................................................................................... 305
Data Sources ....................................................................................................................................... 305

Group 00: Internal Values ........................................................................................................... 305
Group 01: Generator Values ....................................................................................................... 306
Group 02: Mains Values ............................................................................................................. 306
Group 05: Controller Set Points .................................................................................................. 307
Group 06: DC Analog Input Values............................................................................................. 307
Group 07: Engine Values ............................................................................................................ 308
Reference Values ................................................................................................................................ 310
Generator Rated Voltage ............................................................................................................ 310
Mains Rated Voltage ................................................................................................................... 310
Rated Frequency......................................................................................................................... 311
Generator Rated Active Power ................................................................................................... 311
Generator Rated Reactive Power ............................................................................................... 312
Mains Rated Active Power .......................................................................................................... 312
Mains Rated Reactive Power...................................................................................................... 313
Generator Rated Apparent Power .............................................................................................. 313
Mains Rated Apparent Power ..................................................................................................... 314
Generator / Mains Power Factor ................................................................................................. 315
Generator Rated Current ............................................................................................................ 316
Mains Rated Current ................................................................................................................... 316
Rated Speed ............................................................................................................................... 316
Battery Voltage............................................................................................................................ 317
Busbar 1 Rated Voltage .............................................................................................................. 317
Display Value Format .................................................................................................................. 317
Page 6/339
Woodward
Manual 37427
APPENDIX D. EVENT HISTORY .............................................................................................. 318

Resetting the Event History ......................................................................................................... 318
Resetting the Event History Using the Front Panel ................................................................................318

Event List................................................................................................................................................318
Alarm List ...............................................................................................................................................318
APPENDIX E. TRIGGERING CHARACTERISTICS....................................................................... 321
Time-Dependent Overshoot Monitoring ............................................................................................... 321

Two-Level Overshoot Monitoring ......................................................................................................... 322
Two-Level Undershoot Monitoring ....................................................................................................... 323
Two-Level Reversed/Reduced Load Monitoring .................................................................................. 324
Two-Level Unbalanced Load Monitoring ............................................................................................. 325
One-Level Asymmetry Monitoring ........................................................................................................ 326
APPENDIX F. CHARACTERISTICS OF THE VDO INPUTS .......................................................... 327
VDO Input "Pressure" (0 to 5 bar / 0 to 72 psi) - Index "III" ................................................................. 327

VDO Input "Pressure" (0 to 10 bar / 0 to 145 psi) - Index "IV" ............................................................. 328
VDO Input "Temperature" (40 to 120 C / 104 to 248 F) - Index "92-027-004" .................................. 329
VDO Input "Temperature" (50 to 150 C / 122 to 302 F) - Index "92-027-006" .................................. 330
Pt100 RTD............................................................................................................................................ 331
APPENDIX G. LDSS FORMULAS ........................................................................................... 332
Abbreviations ....................................................................................................................................... 332

LDSS Mode Reserve Power ................................................................................................................ 332
Isolated Operation ....................................................................................................................... 332
Changing the Engine Combination to Increase Rated Power.................................................................332

Changing the Engine Combination to Reduce Rated Power ..................................................................332
Mains Parallel Operation (Import/Export Control) ....................................................................... 332
Starting the First Engine Combination (no engine supplies the busbar) .................................................332
Changing the Engine Combination to Reduce Rated Power ..................................................................332
Stopping the Last Engine Combination (load close to minimum load)....................................................332
LDSS Mode Generator Load................................................................................................................ 333

Isolated Operation ....................................................................................................................... 333

Changing the Engine Combination to Reduce Rated Power (except dynamic set point is not matched)333
Mains Parallel Operation (Import/Export Control) ....................................................................... 333
Starting the First Engine Combination (no engine supplies the busbar) .................................................333
Changing the Engine Combination to Reduce Rated Power (except dynamic set point is not matched)333
Stopping the Last Engine Combination (load close to minimum load)....................................................333
LDSS Dynamic ..................................................................................................................................... 333
APPENDIX H. SERVICE OPTIONS .......................................................................................... 334
Product Service Options ...................................................................................................................... 334

Returning Equipment For Repair ......................................................................................................... 334
Packing A Control ........................................................................................................................ 335
Return Authorization Number RAN ............................................................................................. 335
Replacement Parts ............................................................................................................................... 335
How To Contact Woodward ................................................................................................................. 336
Engineering Services ........................................................................................................................... 337
Technical Assistance ........................................................................................................................... 338
Woodward
Page 7/339
Manual 37427
Figures and Tables

Figures
Figure 2-1: ToolKit - Options window ..................................................................................................................................... 15
Figure 2-2: ToolKit - visualization screen ................................................................................................................................ 19
Figure 2-3: ToolKit - analog value trending screen .................................................................................................................. 19
Figure 2-4: ToolKit - configuration screen ............................................................................................................................... 20
Figure 3-1: Code level display .................................................................................................................................................. 31
Figure 3-2: Configure measurement - generator type selection ................................................................................................ 37
Figure 3-3: AC power triangle .................................................................................................................................................. 39
Figure 3-4: Monitoring - calculated generator ground fault ...................................................................................................... 70
Figure 3-5: Monitoring - calculated generator ground current - vector diagram ....................................................................... 71
Figure 3-6: Monitoring - generator inverse time-overcurrent - "Normal inverse" characteristic .............................................. 75
Figure 3-7: Monitoring - generator inverse time-overcurrent - "Highly inverse" characteristic ............................................... 76
Figure 3-8: Monitoring - generator inverse time-overcurrent - "Extremely inverse" characteristic .......................................... 76
Figure 3-9: Monitoring - generator lagging power factor ......................................................................................................... 79
Figure 3-10: Monitoring - generator leading power factor........................................................................................................ 81
Figure 3-11: Monitoring - phase shift ....................................................................................................................................... 95
Figure 3-12: Monitoring - plausibility check n/f ..................................................................................................................... 104
Figure 3-13: Monitoring - flexible limits - data source selection ............................................................................................ 121
Figure 3-14: Monitoring - miscellaneous parameter alignment ........................................................................................... 135
Figure 3-15: Normally Open / Normally Closed contacts ....................................................................................................... 149
Figure 3-16: Analog input scaling - table (example)............................................................................................................... 156
Figure 3-17: Discrete inputs - alarm/control inputs - operation logic ..................................................................................... 166
Figure 3-18: Monitoring - analog outputs - data source selection ........................................................................................... 173
Figure 3-19: Configure application - engine - preglow criterion selection.............................................................................. 177
Figure 3-20: Start /stop sequence - diesel engine .................................................................................................................... 178
Figure 3-21: Start /stop sequence - gas engine - successful .................................................................................................... 180
Figure 3-22: Start /stop sequence - gas engine - unsuccessful ................................................................................................ 181
Figure 3-23: Engine - firing speed and engine delayed monitoring ........................................................................................ 183
Figure 3-24: Engine - Auxiliary services timing ..................................................................................................................... 186
Figure 3-25: Automatic run - engine start conditions ............................................................................................................. 192
Figure 3-26: Automatic - Critical operation at busbar ............................................................................................................ 210
Figure 3-27: Automatic - Critical operation at generator ........................................................................................................ 212
Figure 3-28: Controllers - Behavior of the derivative parameter ............................................................................................ 216
Figure 3-29: CAN bus load/var sharing, diagram ................................................................................................................... 240
Figure 3-30: Load sharing - grouping ..................................................................................................................................... 243
Figure 3-31: Interfaces - Principle of PDO mapping .............................................................................................................. 250
Figure 3-32: LogicsManager - function overview .................................................................................................................. 271
Figure 3-33: LogicsManager - display in ToolKit .................................................................................................................. 272
Figure 3-34: LogicsManager - display on LCD screen ........................................................................................................... 272
Figure 3-35: Reference values - power factor scaling ............................................................................................................. 315
Figure 3-36: Triggering characteristics - three-level time-dependent overshoot montitoring ................................................. 321
Figure 3-37: Triggering characteristics - two-level overshoot montitoring............................................................................. 322
Figure 3-38: Triggering characteristics - two-level undershoot montitoring........................................................................... 323
Figure 3-39: Triggering characteristics - two-level reversed/reduced load montitoring ......................................................... 324
Figure 3-40: Triggering characteristics - two-level unbalanced load montitoring .................................................................. 325
Figure 3-41: Triggering characteristics - one-level asymmetry montitoring ........................................................................... 326
Figure 3-42: Analog inputs - characteristics diagram VDO 0 to 5 bar, Index "III" ................................................................. 327
Figure 3-43: Analog inputs - characteristics diagram VDO 0 to 10 bar, Index "IV"............................................................... 328
Figure 3-44: Analog inputs - characteristics diagram VDO 40 to 120 C, Index "92-027-004" ............................................. 329
Figure 3-45: Analog inputs - characteristics diagram VDO 50 to 150 C, Index "92-027-006" ............................................. 330
Figure 3-46: Analog inputs - characteristics diagram Pt100 ................................................................................................... 331
Page 8/339
Woodward
Manual 37427
Tables
Table 1-1: Manual - overview ................................................................................................................................................... 11
Table 3-1: Configuration - standard values - configure language/clock .................................................................................... 26
Table 3-2: Daylight saving time - configuration example ......................................................................................................... 29
Table 3-3: Daylight saving time - examplary dates ................................................................................................................... 29
Table 3-4: Configuration - standard values - enter password .................................................................................................... 30
Table 3-5: Configuration - standard values - system management............................................................................................ 32
Table 3-6: Configuration - standard values - system management: password system............................................................... 34
Table 3-7: Measurement - standard values - configure measurement ....................................................................................... 36
Table 3-8: Measurement - standard values - configure transformer .......................................................................................... 42
Table 3-9: Monitoring - standard values - configure generator monitoring .............................................................................. 47
Table 3-10: Monitoring - standard values - configure generator operating voltage / frequency................................................ 48
Table 3-11: Monitoring - standard values - generator overfrequency ....................................................................................... 49
Table 3-12: Monitoring - standard values - generator underfrequency ..................................................................................... 51
Table 3-13: Monitoring - standard values - generator overvoltage ........................................................................................... 53
Table 3-14: Monitoring - standard values - generator undervoltage ......................................................................................... 55
Table 3-15: Monitoring - standard values - generator time-overcurrent ................................................................................... 57
Table 3-16: Monitoring - standard values - generator reverse / reduced power ........................................................................ 59
Table 3-17: Monitoring - standard values - generator overload IOP ......................................................................................... 61
Table 3-18: Monitoring - standard values - generator overload MOP ....................................................................................... 63
Table 3-19: Monitoring - standard values - generator unbalanced load .................................................................................... 65
Table 3-20: Monitoring - standard values - generator voltage asymmetry ................................................................................ 68
Table 3-21: Monitoring - standard values - generator ground fault........................................................................................... 71
Table 3-22: Monitoring - standard values - generator voltage phase rotation ........................................................................... 73
Table 3-23: Monitoring - standard values - generator inverse time-overcurrent ....................................................................... 77
Table 3-24: Monitoring - standard values - generator lagging power factor ............................................................................. 79
Table 3-25: Monitoring - standard values - generator leading power factor ............................................................................. 81
Table 3-26: Monitoring - standard values - configure mains monitoring .................................................................................. 83
Table 3-27: Monitoring - standard values - configure mains operating voltage / frequency ..................................................... 83
Table 3-28: Monitoring - standard values - mains decoupling .................................................................................................. 85
Table 3-29: Monitoring - standard values - mains overfrequency ............................................................................................. 87
Table 3-30: Monitoring - standard values - mains underfrequency ........................................................................................... 89
Table 3-31: Monitoring - standard values - mains overvoltage ................................................................................................. 91
Table 3-32: Monitoring - standard values - mains undervoltage ............................................................................................... 93
Table 3-33: Monitoring - standard values - mains phase shift .................................................................................................. 95
Table 3-34: Monitoring - standard values - mains voltage phase rotation................................................................................. 98
Table 3-35: Monitoring - standard values - engine overspeed ................................................................................................ 100
Table 3-36: Monitoring - standard values - engine underspeed .............................................................................................. 102
Table 3-37: Monitoring - standard values - plausibility control n/f......................................................................................... 105
Table 3-38: Monitoring - standard values - generator active power mismatch ....................................................................... 106
Table 3-39: Monitoring - standard values - mains active power mismatch ............................................................................. 107
Table 3-40: Monitoring - standard values - generator unloading mismatch ............................................................................ 108
Table 3-41: Monitoring - standard values - engine start failure .............................................................................................. 109
Table 3-42: Monitoring - standard values - engine shutdown malfunction ............................................................................. 110
Table 3-43: Monitoring - standard values - engine unintended stop ....................................................................................... 111
Table 3-44: Monitoring - standard values - engine dead bus operation................................................................................... 112
Table 3-45: Monitoring - standard values - engine charge alternator failure .......................................................................... 113
Table 3-46: Monitoring - standard values - breaker monitoring - GCB .................................................................................. 114
Table 3-47: Monitoring - standard values - breaker monitoring - GCB synchronization ........................................................ 115
Table 3-48: Monitoring - standard values - breaker monitoring - MCB ................................................................................. 116
Table 3-49: Monitoring - standard values - breaker monitoring - MCB synchronization ....................................................... 118
Table 3-50: Monitoring - standard values - mains voltage phase rotation............................................................................... 119
Table 3-51: Monitoring - standard values - flexible limits ...................................................................................................... 120
Table 3-52: Monitoring - flexible limit examples ................................................................................................................... 120
Table 3-53: Monitoring - flexible limits - analog value examples .......................................................................................... 122
Table 3-54: Monitoring - flexible limits - parameter IDs ........................................................................................................ 123
Table 3-55: Monitoring - standard values - CAN bus overload .............................................................................................. 125
Table 3-56: Monitoring - standard values - CANopen interface 1 .......................................................................................... 126
Table 3-57: Monitoring - standard values - CANopen interface 2 .......................................................................................... 127
Table 3-58: Monitoring - standard values - J1939 interface .................................................................................................... 128
Table 3-59: Monitoring - standard values - J1939 interface red stop lamp ............................................................................. 129
Table 3-60: Monitoring - standard values - J1939 interface amber warning lamp .................................................................. 130
Table 3-61: Monitoring - standard values - battery overvoltage ............................................................................................. 131
Table 3-62: Monitoring - standard values - battery undervoltage ........................................................................................... 133
Table 3-63: Monitoring - standard values - multi-unit parameter alignment monitoring ........................................................ 135
Table 3-64: Monitoring - standard values - multi-unit missing members monitoring ............................................................. 137
Woodward
Page 9/339
Manual 37427
Table 3-65: Application - standard values - configure breakers.............................................................................................. 138

Table 3-66: Application - standard values - configure GCB ................................................................................................... 149
Table 3-67: Application - standard values - configure MCB .................................................................................................. 153
Table 3-68: Application - standard values - configure synchronization .................................................................................. 155
Table 3-69: Application - standard values - configure analog inputs ...................................................................................... 156
Table 3-70: Application - standard values - configure analog input table A / B ..................................................................... 157
Table 3-71: Analog inputs - table characteristics - parameter IDs .......................................................................................... 158
Table 3-72: Application - standard values - configure analog inputs 1 to 3 ............................................................................ 159
Table 3-73: Discrete inputs - terminal assignment .................................................................................................................. 166
Table 3-74: Application - standard values - configure discrete inputs .................................................................................... 166
Table 3-75: Discrete inputs - parameter IDs ........................................................................................................................... 168
Table 3-76: Application - standard values - configure discrete inputs .................................................................................... 169
Table 3-77: External discrete inputs - parameter IDs .............................................................................................................. 169
Table 3-78: Relay outputs - assignment .................................................................................................................................. 170
Table 3-79: Discrete outputs - parameter IDs ......................................................................................................................... 170
Table 3-80: External discrete outputs - parameter IDs ............................................................................................................ 171
Table 3-81: Analog outputs 1/2 - parameter table ................................................................................................................... 171
Table 3-82: Application - standard values - configure analog outputs 1/2 .............................................................................. 171
Table 3-83: Analog outputs 3/4 - parameter table ................................................................................................................... 172
Table 3-84: Application - standard values - configure analog outputs 3/4 .............................................................................. 172
Table 3-85: Analog outputs - signal type selection ................................................................................................................. 174
Table 3-86: Application - standard values - configure engine type ......................................................................................... 176
Table 3-87: Application - standard values - configure start/stop ............................................................................................ 182
Table 3-88: Application - standard values - configure MPU .................................................................................................. 187
Table 3-89: MPU input - typical configurations ..................................................................................................................... 187
Table 3-90: Application - standard values - configure idle mode ........................................................................................... 188
Table 3-91: Application - standard values - configure emergency run ................................................................................... 190
Table 3-92: Application - standard values - configure automatic run ..................................................................................... 191
Table 3-93: Load-dependent start/stop - parameters for reserve power operation .................................................................. 193
Table 3-94: Load-dependent start/stop - parameters for generator load operation .................................................................. 194
Table 3-95: Application - standard values - configure load dependent start/stop.................................................................... 196
Table 3-96: Application - standard values - configure load dependent start/stop IOP ............................................................ 201
Table 3-97: Load-dependent start/stop - dynamic influence on stopping a genset .................................................................. 204
Table 3-98: Application - standard values - configure load dependent start/stop MOP .......................................................... 205
Table 3-99: Application - standard values - configure critical mode ...................................................................................... 214
Table 3-100: Application - standard values - configure frequency control ............................................................................. 217
Table 3-101: Application - standard values - configure load control ...................................................................................... 223
Table 3-102: Application - standard values - configure voltage control ................................................................................. 229
Table 3-103: Application - standard values - configure power factor control ......................................................................... 234
Table 3-104: Application - standard values - configure load share ......................................................................................... 241
Table 3-105: Application - standard values - configure discrete raise/lower function ............................................................ 245
Table 3-106: Application - standard values - configure CAN interface 1 ............................................................................... 246
Table 3-107: Application - standard values - configure CAN interface 1: additional Server SDOs ....................................... 249
Table 3-108: Application - standard values - configure CAN interface 1: receive PDOs ....................................................... 250
Table 3-109: Application - standard values - configure CAN interface 1: transmit PDOs...................................................... 252
Table 3-110: Application - standard values - configure CAN interface 2 ............................................................................... 255
Table 3-111: Application - standard values - configure CAN interface 2: CANopen ............................................................. 255
Table 3-112: Application - standard values - configure CAN interface 2: J1939 ................................................................... 257
Table 3-113: Application - standard values - configure CAN interface: load share ................................................................ 260
Table 3-114: Application - standard values - configure RS-232 interface: serial interface 1 .................................................. 261
Table 3-115: Application - standard values - configure RS-485 interface: serial interface 2 .................................................. 262
Table 3-116: Application - standard values - configure LogicsManager ................................................................................ 263
Table 3-117: Internal flags - parameter IDs ............................................................................................................................ 263
Table 3-118: Application - standard values - configure counters............................................................................................ 266
Table 3-119: LogicsManager - command overview ............................................................................................................... 271
Table 3-120: LogicsManager - logical symbols...................................................................................................................... 272
Table 3-121: Relay outputs - terminal assignment .................................................................................................................. 276
Table 3-122: Analog Manager - display value format ............................................................................................................ 307
Table 3-123: Event history - event list .................................................................................................................................... 318
Table 3-124: Event history - alarm list.................................................................................................................................... 320
Table 3-125: Analog inputs - characteristics diagram VDO 0 to 5 bar, Index "III" ................................................................ 327
Table 3-126: Analog inputs - characteristics diagram VDO 0 to 10 bar, Index "IV" .............................................................. 328
Table 3-127: Analog inputs - characteristics diagram VDO 40 to 120 C, Index "92-027-004" ............................................ 329
Table 3-128: Analog inputs - characteristics diagram VDO 50 to 150 C, Index "92-027-006" ............................................ 330
Table 3-129: Analog inputs - characteristics diagram Pt100................................................................................................... 331
Page 10/339
Woodward
Manual 37427
Chapter 1.
General Information
Document Overview
Type
easYgen-2000 Series
easYgen-2000 Series - Installation
easYgen-2000 Series - Configuration
easYgen-2000 Series - Operation
easYgen-2000 Series - Application
easYgen-2000 Series - Interfaces
easYgen-2000 Series - Parameter List
easYgen-2000 Series - Brief Operation
Information
this manual
English
German
37426
37427
37428
37429
37430
37431
37432
DE37426
DE37427
DE37428
DE37431
DE37432
Table 1-1: Manual - overview
Intended Use The unit must only be operated for the uses described in this manual. The prerequisite for a proper
and safe operation of the product is correct transportation, storage, and installation as well as careful operation
and maintenance.
NOTE
This manual has been developed for a unit fitted with all available options. Inputs/outputs, functions,
configuration screens and other details described, which do not exist on your unit may be ignored.
The present manual has been prepared to enable the configuration of the unit. On account of the large
variety of parameter settings, it is not possible to cover every possible combination. The manual is
therefore only a guide. In case of incorrect entries or a total loss of functions, the default settings can
be taken from the Parameter List 37431 or from ToolKit and the respective *.SID file.
NOTE
Some parameters, inputs, and outputs are dependent on the configured application mode
(parameter 3401 on page 139) regarding their availability and/or function. The following abbreviations
indicate the application mode for which the concerned information is valid:
{0}
{0 (breaker control)} Application mode setting "None" - "Measuring transducer and engine
control function"
The control unit enables engine start/stop and generator measuring and protection no breaker
control.
{1o} {1 (breaker) open} Application mode setting "GCB open" - "1 breaker control function"
The control unit enables engine start/stop and generator measuring and protection "GCB
open" breaker control.
{1oc} {1 (breaker) open/close} Application mode setting "GCB" - "1 breaker control function"
The control unit enables engine start/stop and generator measuring and protection full
generator breaker control for stand-by power applications with soft generator load transfer.
{2oc} {2 (breaker) open/close} Application mode setting "GCB/MCB" - "2 breaker control function"
The control unit enables engine start/stop and generator measuring and protection full
generator breaker control for stand-by power applications with soft generator load transfer plus
emergency power, open/closed transition, and interchange load transfer applications.
Woodward
Page 11/339
Manual 37427
Abbreviations
The following abbreviations are frequently used throughout this and all other easYgen manuals:
CB
CL
CT
CCW
CW
DI
DO
ECU
GCB
IOP
LDSS
MCB
MOP
MPU
N.C.
N.O.
PF
PID
PLC
P/N
PT
S/N
Circuit Breaker
Code Level
Current Transformer
Counter-Clockwise
Clockwise
Discrete Input
Discrete (Relay) Output
Engine Control Unit
Generator Circuit Breaker
Isolated Operation in Parallel
Load-Dependent Start/Stop operation
Mains Circuit Breaker
Mains Operation in Parallel
Magnetic Pickup Unit
Normally Closed (break) contact
Normally Open (make) contact
Power Factor
Proportional Integral Derivative controller
Programmable Logic Control
Part Number
Potential (Voltage) Transformer
Serial Number
Page 12/339
Woodward
Manual 37427
Chapter 2.
Configuration
Configuration Via The Front Panel
Operation of the unit via the front panel is explained in the operation manual 37428. This manual will familiarize
you with the unit, the meanings/functions of the buttons, and the display.
Woodward
Page 13/339
Manual 37427
Configuration Using The PC
Install ToolKit Configuration and Visualization Software

CAUTION
Woodwards ToolKit software (version 3.1 or higher) is required when configuring the unit via a PC.
ToolKit from 3.1

If not already installed, download and install the ToolKit software. Please proceed as follows for this:
Open your web browser and go to http://www.woodward.com/software/
Select ToolKit in the list and click the Go button
Download and install the file as described on the download page
Minimum system requirements for installing ToolKit:
Microsoft Windows Vista, XP

Microsoft .NET Framework Ver. 3.5
600 MHz Pentium CPU
96 MB of RAM
Minimum 800 by 600 pixel screen with 256 colors
Serial Port
NOTE
Please note that you must register on the website prior to downloading the software.
Microsoft .NET Framework 3.5 must be installed on your computer to be able to install ToolKit. If not
already installed, Microsoft .NET Framework 3.5 will be installed automatically. You must be connected
to the internet for this.
NOTE
If your computer is equipped with a Bluetooth interface please deactivate it temporary for the case that
ToolKit is freezing building up a connection.
Page 14/339
Woodward
Manual 37427
Configure ToolKit
Open ToolKit via Start menu -> Program ->Woodward -> ToolKit 3.x
You may configure the default settings of ToolKit by selecting Tools -> Options from the toolbar. The options
window will be displayed where you may select the default COM port and the default path for the configuration
files. We recommend configuring a dedicated ToolKit data file directory (e.g. C:\Data\ToolKit) instead of storing
the configuration files in the ToolKit installation directory (e.g. C:\Program Files\Woodward\ToolKit). The
changes become effective after restarting ToolKit.
Figure 2-1: ToolKit - Options window
Woodward
Page 15/339
Manual 37427
NOTE
Be sure to have the correct *.SID and *.WTOOL files for your unit ready. The SID file must not be
renamed!
When installing the *.SID and *.WTOOL files on a computer, it is recommended to create a dedicated
ToolKit data file external to the ToolKit program. An example of this would be to create a Woodward
ToolKit folder in a Data directory to store the *.SID and *.WTOOL files. The data files should be kept
separate from the program files. Mixing data and program files makes backing up files more difficult
and uninstalling the files incomplete.
ToolKit Files
ToolKit is using the following files:
*.WTOOL
File name composition: [P/N1]-[Revision]_[Language ID]_[P/N2]-[Revision]_[# of visualized gens].WTOOL
Example file name:
8440-1884-NEW_US_5418-3090-NEW_32.WTOOL
Content of the file:
Display screens and pages for online configuration, which are associated with the
respective *.SID file
*.SID
File name composition: [P/N2]-[Revision].SID
Example file name:
5418-3090-NEW.SID
All display and configuration parameters available in ToolKit
*.WSET
File name composition: [user defined].WSET
Example file name:
easYgen_settings.WSET
Default settings of the ToolKit configuration parameters provided by the SID file or
user-defined settings read out of the unit.
P/N1 = Part number of the unit
P/N2 = Part number of the software in the unit
NOTE
The P/N2 and revision information in the *.SID file name is used for identifying the unit and must not be
renamed.
When opening a *.WTOOL file, ToolKit will look for the respective SID file in the SID file location,
configured in the Options dialog (refer to Figure 2-1).
The *.SID files have identical names regardless of the language and are located in the respective
language folders delivered with the unit. If it happens that you need to switch between different
languages in ToolKit, we recommend to store your *.SID (and *.WTOOL & *.WSET) files in different
folders to avoid confusion. In this case you only need to change the path information as described
under Configure ToolKit on page 15 to switch the language. Refer to the Language-Dependent SID Files
section on page 17 for more details.
Page 16/339
Woodward
Manual 37427
Language-Dependent SID Files

Every language comes with a separate *.sid file. At the moment, only English and German are provided. Due to
current internal structures the *.sid files for every specific language have the same file name.
Therefore, a user will only be able to check the language by opening the *.sid file using an editor. Another
possibility is to select New from SID defaults from the Settings menu in ToolKit. If you select the respective
*.sid file then, a Settings Editor window opens, which displays the language ID ("us" or "de") in the title.
If a "German" version of *.wtool (8440-1884-NEW_de_5418-3090-NEW_32.wtool) tries to open an English
*.sid file, error messages and a red cross are displayed on the screen upon connecting.
If it is required that both language versions of the *.sid file are stored on the computer, because the user wants to
be able to switch between the languages, the *.sid files need to be stored in separate subfolders and the subfolder
name needs to show the name of the appropriate language.
If the user needs to change the language, the appropriate *.sid file needs to be selected by using the ToolKit menu
Tools -> Options -> SID file directories. The folder with the desired language needs to be on top position.
ToolKit needs to be closed and the *.wtool file must be opened again, to ensure that the new *.sid file will be
loaded.
SID Files for Using ToolKit on the CAN Bus With Other CANopen Devices
If a PC with ToolKit is connected to the easYgen via a CAN bus with other external CANopen devices (like a
Phoenix Contact I/O expansion board, for example), it may happen that ToolKit cannot establish a connection
with the easYgen because it looks for a SID file for such an external device, which does not exist.
A special *.sid file can be created in this case. Contact Woodward for support or create a *.sid file with the
following content:
<?xml version="1.0" encoding="utf-8"?>
<ServiceInterfaceDefinition xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" Identifier="[add the
required device application name here]" Specification="EmptyFile">
</ServiceInterfaceDefinition>
The file name must be the same as the Identifier plus the extension *.sid. The file must be stored to the
configured SID file directory.
Loading WSET Files of Previous Revisions
There may be incompatibilities between different easYgen P/Ns and revisions of the same P/N when loading a
*.wset file, saved from an easYgen into an easYgen with a different P/N and/or revision. Proceed as follows to
avoid that settings may get lost or transferred incorrectly:
Select from the ToolKit menu Settings -> Save from Device to File to store the current easYgen settings (note
that the correct *.sid file is available). Then select from the ToolKit menu Settings -> Load Settings File to
Device to load the stored settings into a different easYgen (take care that you provide the correct *.sid file in
the same language that was used to store the *.wset file). If the P/Ns and/or revisions of the easYgens differ, you
will be prompted to resolve the differences. If you are sure that the *.wset file is compatible with the easYgen,
proceed with Next. If you are not sure, proceed with Resolve Differences (please note that this feature is not
supported properly by the CANopen driver). If you select Resolve Differences it may take some minutes until the
next window opens, because ToolKit reads out all settings from the device to compare them with those in the
*.wset file. Then, a Compare Differences window will open and display all differences in value and/or parameter
name. Most of the name differences can be mapped according to the same index number within the parameter
name. Settings of parameters with selectable options cannot be mapped.
Verify all settings after loading them into the different easYgen! To verify the settings save them again from the
easYgen to a *.wset file. Then select ftom the ToolKit menu Settings -> Compare Settings File Differences and
open both, the (old) *.wset file loaded into the easYgen before, and the newly saved *.wset file. If there are no
value differences displayed, the load process was successful. If there are any value differences, take care that they
will be adjusted properly.
If there are any name differences, take care that the settings of the new parameters will be verified to fit the
application purpose.
Woodward
Page 17/339
Manual 37427
Connect ToolKit and the easYgen Unit

For configuration of the unit via ToolKit please proceed as follows:
Connect the null modem communications cable between your laptop/PC and the control unit. Plug the null
modem cable into the RS-232 serial port on unit and the other side to a serial COM port of the laptop/PC. If
the laptop/PC does not have a serial port to connect the null modem cable to, use a USB to serial adapter.
Open ToolKit via Start menu -> All Programs -> Woodward -> ToolKit 3.x
From the main ToolKit window, click File then select Open Tool..., or click the Open Tool icon
on the
tool bar.
Locate and select the desired tool file (*.WTOOL) in the ToolKit data file directory and click Open.
From the main ToolKit window, click Device then click Connect, or select the Connect icon
on the
toolbar.
The Connect dialog window will open if the option is enabled.
Select the COM port that is connected to the communication cable.
Click the OK button.
If the Communications window opens, select ToolConfigurator under Tool Device and close the
Communications window.
The identifier of the device that ToolKit is connected to will display in the status bar.
Now you are able to edit the easYgen parameters. Any changes made are written to the control memory
automatically.
NOTE
A null modem serial cable must be used for communicating with the easYgen-2000 Series to ensure
that the controller functions properly. The connection will not work if you are using a straight cable (a
null modem cable has crosslinked transmit and receive lines in contrast to a straight serial cable).
NOTE
Depending on the computer used and the installed operation system, problems with the
communication via an infrared connection may occur.
NOTE
It is also possible to connect to the unit via CAN bus. If a suitable CAN adapter is used, this may be
selected in the Connect window. We recommend to use the IXXAT USB-to-CAN converter using the VCI
V3 driver.
Be sure to configure the correct baud rate and timeout in the Properties dialog of the Connect window.
The Password for CAN Interface 1 (parameter 10402 on page 31) must be entered before being able to
edit the parameters.
Page 18/339
Woodward
Manual 37427
View easYgen Data with ToolKit

The following figure shows a visualization screen of ToolKit:
Figure 2-2: ToolKit - visualization screen
Navigation through the various visualization and configuration screens is performed by clicking on the
and
icons, by selecting a navigation button, or by selecting a screen from the drop-down list to the right of
the arrow icons.
It is possible to view a trend chart of up to eight values with the trending tool utility of ToolKit. The following
figure shows a trending screen of the measured battery voltage value:
Figure 2-3: ToolKit - analog value trending screen
Each visualization screen provides for trending of monitored values by right-clicking on a value and selecting the
"Add to trend" function. Trending is initiated by clicking on the Start button. Clicking the Export button will
save the trend data to a Comma Separated Values (CSV) file for viewing, editing or printing with office software,
like Microsoft Excel, etc. The Properties button is used to define high and low limits of the scale, sample rate,
displayed time span and color of the graph. The trend functionality is not available if ToolKit is used utilizing a
CAN bus connection to the unit.
Woodward
Page 19/339
Manual 37427
Configure the easYgen with ToolKit

The following figure shows a configuration screen of ToolKit:
Figure 2-4: ToolKit - configuration screen
Entering a new value or selecting a value from a defined list will change the value in a field. The new value is
written to the controller memory by changing to a new field or pressing the Enter key.
Navigation through the various configuration and visualization screens is performed by clicking on the
and
icons, by selecting a navigation button, or by selecting a screen from the drop-down list to the right of
the arrow icons.
The Settings File Function of ToolKit

ToolKit allows you to manage device application settings as well as file based settings.
To create a settings file you can save a devices' settings to a file or create device settings from application (SID)
defaults.
After you have a settings file, you can view and edit it, compare it to another settings file, associate it with a
different application, or merge it with an application file (OH2 only).
Settings files can be exported to a Hypertext Markup Language (html) file for viewing, editing or printing with
office software, like Microsoft Excel, etc.
Refer to the ToolKit Help for a description of working with settings. From the main ToolKit window, click Help
then click Help Contents to open the ToolKit Help window.
Page 20/339
Woodward
Manual 37427
Function of the Inputs and Outputs
Discrete Inputs
The discrete inputs may be grouped into two categories:
programmable
The discrete input has been assigned a default function using either the LogicsManager or preconfigured
alarms such as "emergency stop". The following text describes how these functions are assigned. It is possible
to change the function of the discrete input if required.
The following description of the inputs, labeled with programmable, refers to the preconfiguration.
fixed
The discrete input has a specific function that cannot be changed depending upon the configured application
mode.
programmable, pre-configured for discrete input [DI 1], terminals 43/44
Emergency stop {0}, {1o}, {1oc}, or {2oc}
This discrete input is configured as alarm class F and is not delayed by the engine speed.
Start request in AUTO {0}, {1o}, {1oc}, or {2oc}
Enabled in the AUTOMATIC operation mode
energized ..... If the unit is in the AUTOMATIC operation mode (selected with the operating mode
selection push button on the front panel) the controlled engine is started automatically.
de-energized The engine is stopped.
This discrete input is configured as a Control input in the alarm class and is not delayed by the engine
speed.
Low oil pressure {0}, {1o}, {1oc}, or {2oc}
This discrete input is configured as alarm class B and is delayed by the engine speed.
Coolant temperature {0}, {1o}, {1oc}, or {2oc}
This discrete input is configured as alarm class B and is not delayed by the engine speed.
programmable, pre-configured for discrete input [DI 5], term. 43/48
External acknowledgement {0}, {1o}, {1oc}, or {2oc}
This discrete input is used as a remote acknowledgement for alarms. The input is normally deenergized. When an alarm is to be acknowledged the input is energized. The first time an alarm in
acknowledged, the centralized alarm/horn is silenced. When the input is energized a second time, all
alarms, which are no longer active, will be acknowledged.
speed.
Release MCB {2oc}
energized ..... The MCB is enabled and closure of the breaker is permitted.
de-energized The MCB is not enabled and closure of the breaker is not permitted. This function
permits a supervisory control (i.e. a PLC) to allow the closure of the MCB by the
easYgen.
speed.
Woodward
Page 21/339
Manual 37427
Reply MCB {2oc}

Note: Negative logic function!

programmable, pre-configured to discrete input [DI 7], terminals 43/50
The controller utilizes the CB auxiliary (B) contacts into this discrete input to reflect the state of the
MCB. This discrete input must be energized to show when the breaker is open and de-energized to
show when the MCB is closed. The status of the MCB is displayed on the screen.
This input is used in all breaker modes to change between frequency/voltage and power/power factor
control (refer to below note).
Reply GCB {1oc} or {2oc}
Note: Negative function logic!
fixed to discrete input [DI 8], terminals 43/51
The controller utilizes the CB auxiliary (B) contacts into this discrete input to reflect the state of the
GCB. This discrete input must be energized to show when the breaker is open and de-energized to show
when the GCB is closed. The status of the GCB is displayed on the screen.
This input is used in all breaker modes to enable reverse power protection, overload MOP protection,
mains decoupling and the activation of the load sharing (refer to below note).
Discrete Input 9 {0}, {1o}, {1oc}, or {2oc}
Discrete Input 10 {0}, {1o}, {1oc}, or {2oc}
NOTE
The easYgen decides whether it performs voltage and frequency (V/f) control or power and power
factor (P/PF) control using the reply of the circuit breakers, i.e. the discrete inputs DI 7 and DI 8.
If the GCB is open, only V/f control is performed
If the GCB is closed and the MCB is open, V/f control as well as active and reactive power load sharing
is performed
If the GCB is closed and the MCB is closed, P/PF control or import power control with load sharing and
PF control is performed.
Alarm inputs {0}, {1o}, {1oc}, or {2oc}

All discrete inputs, which are not assigned a function, can be used as alarm or control inputs. These
discrete inputs can be freely configured as such. Refer to the section "Configure Discrete Inputs" on
page 166.
Page 22/339
Woodward
Manual 37427
Discrete Outputs
The discrete outputs can be grouped into two categories:
programmable
The discrete output has been assigned a default function using the LogicsManager. The following text
describes how these functions are assigned using the LogicsManager. It is possible to change the function of
the discrete output if required.
The following description of the outputs, labeled with programmable, refers to the preconfiguration.
fixed
The discrete output has a specific function that cannot be changed depending upon the configured application
mode. The discrete output cannot be viewed or changed in the LogicsManager.
NOTE
The discrete outputs can be "programmable" or "fixed" depending on the application mode
(parameter 3401 on page 139). Table 3-78 on page 170 defines the function of the discrete outputs
according to the configured application mode.
fixed to relay [R1], terminals 30/31
Ready for operation OFF {0}, {1o}, {1oc}, or {2oc}
This discrete output is used to ensure that the internal functions of the controller are operating properly.
It is possible to configure additional events, which cause the contacts of this discrete output to open,
using the LogicsManager.
CAUTION
The discrete output "Ready for operation OFF" must be wired in series with an emergency stop
function. This means that it must be ensured that the generator circuit breaker is opened and the
engine is stopped if this discrete output is de-energeized. We recommend to signal this fault
independently from the unit if the availability of the plant is important.
programmable to relay [R2], terminals 32/33
Centralized alarm {0}, {1o}, {1oc}, or {2oc}
When a centralized alarm is issued, this discrete output is enabled. A horn or a buzzer maybe activated
via this discrete output. Pressing the button next to the "" symbol will acknowledge the centralized
alarm and disable this discrete output. The discrete output will re-enable if a new fault condition
resulting in a centralized alarm occurs. The centralized alarm is initiated by class B alarms or higher.
Starter {0}, {1o}, {1oc}, or {2oc}
The generator starting circuit is engaged when this discrete output is enabled. This discrete output will
enable depending on the start sequence (refer to the start sequence description in the Configure
Application: Configure Engine section starting on page 176) to energize the starter for the configured
starter time (parameter 3306 on page 182.
Fuel solenoid / gas valve (Diesel / gas engine) {0}, {1o}, {1oc}, or {2oc}
Fuel solenoid: The fuel solenoid for the diesel engine is energized when this discrete output is enabled.
If the engine is given a stop command or engine speed drops below the configured firing speed, this
discrete output is disabled immediately.
Gas valve: The gas valve for the engine is energized when this discrete output is enabled. If the engine
is given a stop command or engine speed drops below the configured firing speed, this discrete output is
disabled immediately.
Open MCB {2oc}
The controller enables this discrete output when the MCB is to be opened for switching operations.
CAUTION
The circuit breaker commands must be checked before every commissioning because the relays can
be used for different applications and can be assigened to various functions. Please make sure that all
relay outputs are configured correctly.
Woodward
Page 23/339
Manual 37427

Command: close GCB {1oc} or {2oc}
The "Command: close GCB" output issues the signal for the GCB to close. This relay may be
configured as an impulse or constant output signal depending on parameter 3414 on page 150.
If the output is configured as "Impulse", the discrete output will enable for the time configured in
parameter 3416 on page 150). An external holding coil and sealing contacts must be installed into the
GCB closing circuit if this discrete output is configured for an impulse output signal.
If the relay is configured as "Constant", the relay will energize and remain enabled as long as the
discrete input "Reply GCB" remains de-energized and the generator and busbar voltages are identical. If
a class C or higher alarm occurs, this discrete will disable and the GCB will open immediately.
Command: open GCB {1o}, {1oc}, or {2oc}
The parameter 3403 on page 149 defines how this relay functions. If this parameter 3403 is configured
as "N.O.", the relay contacts close resulting in the GCB opening circuit energizing. If this output is
configured as "N.C.", the relay contacts open resulting in the GCB opening circuit de-energizing. If the
controller is configured for the breaker application "None", this relay is freely configurable.
{1o}: The open GCB command remains enabled until the GCB is manually closed and the discrete
input "Reply GCB" is energized. The open GCB command will be issued when a fault condition or an
engine shut down occurs.
{1oc} or {2oc): The controller enables the open GCB command when the GCB is to be opened for
switching operations. If the discrete input "Reply GCB" is energized, the open GCB command will be
disabled.
Command: close MCB {2oc}
The discrete output "Command: close MCB" is an impulse output signal. This discrete output is enabled
for the time configured in parameter 3417 on page 153. An external holding coil and sealing contacts
must be utilized with the MCB closing circuit.
programmable, pre-configured to relay [R9], terminals 84/85
Stop solenoid {2oc}
Inverted function of Fuel solenoid / gas valve (preconfigured [R4])
Auxiliary services {0}, {1o}, {1oc}, or {2oc}
The auxiliary services output (LogicsManager 03.01) will be enabled with the start command (prior to
the engine start because of the prerun time) and remains enabled as long as the engine is running. It will
be disabled after the engine has stopped and the postrun time has expired (i.e. for operating a cooling
pump). Refer to Figure 3-24 on page 186 for this behavior.
The auxiliary services output (LogicsManager 03.01) is always enabled in MANUAL operation mode.
Shutdown alarm {0}, {1o}, {1oc}, or {2oc}
This discrete output is enabled when a shutdown alarm (class C or higher alarm; refer to Alarm Classes
on page 269 for more information) is issued. After all shutdown alarms have been acknowledged, this
discrete output will disable.
Page 24/339
Woodward
Manual 37427
Chapter 3.
Parameters
All parameters are assigned a unique Parameter Identification Number. The Parameter Identification Number
may be used to reference individual parameters listed in this manual. This Parameter Identification Number is
also displayed in the ToolKit configuration screens next to the respective parameter.
Language and parameter text

EN: English parameter text
DE: German parameter text
Caption
Brief description of the parameter.
Setting range
EN
Text English
DE
Permissible limits valid for this parameter.
Text German
CLx
p
{0}
{1o}
{1oc}
{2oc}
Setting range
Caption
Explanations.
Explanations
Detailed parameter description, settings, and the

effects on the controller.
Validity
{0}: Valid for the basic-mode [None]

{1o}: Valid for the 0-CB-mode [GCB open]
{1oc}: Valid for the 1-CB-mode [GCB]
{2oc}: Valid for the 2-CB-mode [GCB/MCB]
{all}: Valid for all application modes
Present in this mode.
Present in this mode, if the function was
configured accordingly.
--- Not present in this mode.
Parameter Display
[CLx] = Visible in code level x or higher

[p] = Parameter Identification Number
[T] = Only displayed in ToolKit for configuration
Woodward
Page 25/339
Manual 37427
Configure Language / Clock
The following parameters are used to set the unit language, the current date and time, and the daylight saving
time feature.
Parameter Table
Level
Text
Configure language / clock
Language
Hour
Minute
Second
Day
Month
Year
Daylight saving time
DST begin time
DST begin weekday
DST begin nth weekday
DST begin month
DST end time
DST end weekday
DST end nth weekday
DST end month
Setting range
Default value
English / Deutsch / Italiano /

Franais / Espaol / Trke /
Russky / Japanese / Protugus /
Chinese / Polish
0 to 23 h
0 to 59 min
0 to 59 s
1 to 31
1 to 12
0 to 99
On / Off
0 to 23
Sunday / Monday / Tuesday /
Wednesday / Thursday / Friday /
Saturday
1st / 2nd / 3rd / 4th / Last /
LastButOne / LastButTwo /
LastButThree
1 to 12
0 to 23
Sunday / Monday / Tuesday /
Wednesday / Thursday / Friday /
Saturday
1st / 2nd / 3rd / 4th / Last /
LastButOne / LastButTwo /
LastButThree
1 to 12
English
(real-time clock)
(real-time clock)
(real-time clock)
(real-time clock)
(real-time clock)
(real-time clock)
Off
2
Sunday
4th
3
3
Sunday
4th
10
DE
EN
Table 3-1: Configuration - standard values - configure language/clock
CL0
1700
{0}
{1o}
Language
Language
{1oc}
{2oc}
Set language
selectable languages
The desired language for the unit display text is configured here.
NOTE
If an Asian language is configured, some parameter screens may be displayed with an empty space at
the bottom of the parameter list, which may be interpreted as an end of the list, although more
parameters exist and are displayed when scrolling down.
DE
EN
Hour
Stunden
CL0
{0}
{1o}
DE
EN
1710
CL0
1709
{0}
Page 26/339
{1o}
{1oc}
{2oc}
Minute
Minuten
{1oc}
{2oc}
Adjust clock: hour
0 to 23 h
The hour of the clock time is set here. Example:

0 ....................0th hour of the day (midnight).
23 ..................23rd hour of the day (11 pm).
Adjust clock: minute
0 to 59 min
The minute of the clock time is set here. Example:

0 ....................0th minute of the hour.
59 ..................59th minute of the hour.
Woodward
DE
EN
Manual 37427
CL0
{0}
{1o}
Second
Sekunden
{1oc}
DE
EN
1708
CL0
{0}
{1o}
{1oc}
DE
EN
1711
CL0
{0}
{1o}
{1oc}
DE
EN
1712
CL0
1713
{0}
{1o}
{1oc}
{2oc}
Day
Tag
{2oc}
Month
Monat
Adjust clock: second
The second of the clock time is set here. Example:

0.................... 0th second of the minute.
59.................. 59th second of the minute.
Adjust clock: day
Adjust clock: month
The month of the date is set here. Example:

1.................... 1st month of the year.
12.................. 12th month of the year.
Year
Jahr
Adjust clock: year
{2oc}
1 to 31
The day of the date is set here. Example:

1.................... 1st day of the month.
31.................. 31st day of the month.
{2oc}
0 to 59 s
1 to 12
0 to 99
The year of the date is set here. Example:

0.................... Year 2000.
99.................. Year 2099.
The daylight saving time feature enables to automatically adjust the real-time clock to local daylight saving time
(DST) provisions. If daylight saving time is enabled, the real-time clock will automatically be advanced by one
hour when the configured DST begin date and time is reached and falls back again by one hour when the
configured DST end date and time is reached. If the unit is used in the southern hemisphere, the DST function
will be inverted automatically, if the DST begin month is later in the year than the DST end month.
NOTE
DE
EN
Do not change the time manually during the hour of the automatic time change if DST is enabled to
avoid a wrong time setting.
Events or alarms, which occur during this hour might have a wrong time stamp.
CL2
4591

Sommerzeitumschaltung
{0}
{1o}
{1oc}
{2oc}
Adjust clock: Enable daylight saving time
On / Off
On ................ Daylight saving time is enabled.

Off ................ Daylight saving time is disabled.
NOTE
DE
EN
The following parameters will only be displayed, if Daylight saving time (parameter 4591) has been
configured to On and the enter button has been pressed.
CL2
4594
DST begin time

Sommerzeitbeginn Uhrzeit
{0}
Woodward
{1o}
{1oc}
{2oc}
Adjust clock: DST begin time
0 to 23 h
The real-time clock will be advanced by one hour when this time is reached on the
DST begin date. Example:
0.................... 0th hour of the day (midnight).
23.................. 23rd hour of the day (11 pm).
Page 27/339
DE
EN
Manual 37427
CL2
4598
DST begin weekday

Sommerzeitbeginn Wochentag
{0}
{1o}
{1oc}
{2oc}
DE
EN
DE
EN
DST begin nth. weekday

Sommerzeitbeginn x. Wochentag
{1o}
{1oc} {2oc}
CL2 {0}
4592
CL2
{0}
DE
CL2
DE
EN
4597
CL2
DE
EN
4599
CL2
4595
{1o}
{1oc}
{2oc}
DST end time

Sommerzeitende Uhrzeit
EN
4593
DST begin month

Sommerzeitbeginn Monat
{0}
{1o}
{1oc}
{2oc}
DST end weekday

Sommerzeitende Wochentag
{0}
{1o}
{1oc}
{2oc}
DST end nth. weekday

Sommerzeitende x. Wochentag
{0}
Page 28/339
{1o}
{1oc}
{2oc}
Adjust clock: DST begin weekday
weekday
The weekday for the DST begin date is configured here

Adjust clock: DST begin nth weekday
weekday order no.
The order number of the weekday for the DST begin date is configured here.
Example:
1st .................DST starts on the 1st configured weekday of the DST begin month.
2nd................DST starts on the 2nd configured weekday of the DST begin month.
3rd ................DST starts on the 3rd configured weekday of the DST begin month.
4th ................DST starts on the 4th configured weekday of the DST begin month.
Last...............DST starts on the last configured weekday of the DST begin month.
LastButOne .DST starts on the last but one configured weekday of the DST
begin month.
LastButTwo .DST starts on the last but two configured weekday of the DST
begin month.
LastButThree . DST starts on the last but three configured weekday of the DST
begin month.
Adjust clock: DST begin month
1 to 12
The month for the DST begin date is configured here. Example:
1 ....................1st month of the year.
12 ..................12th month of the year.
Adjust clock: DST end time
0 to 23 h
The real-time clock will fall back by one hour when this time is reached on the
DST end date. Example:
23 ..................23rd hour of the day (11 pm).
Adjust clock: DST end weekday
weekday
The weekday for the DST end date is configured here

Adjust clock: DST end nth weekday
weekday order no.
The order number of the weekday for the DST end date is configured here.
Example:
1st .................DST ends on the 1st configured weekday of the DST end month.
2nd................DST ends on the 2nd configured weekday of the DST end month.
3rd ................DST ends on the 3rd configured weekday of the DST end month.
4th ................DST ends on the 4th configured weekday of the DST end month.
Last...............DST ends on the last configured weekday of the DST end month.
LastButOne .DST ends on the last but one configured weekday of the DST end
month.
LastButTwo .DST ends on the last but two configured weekday of the DST end
month.
LastButThree . DST ends on the last but three configured weekday of the DST
end month.
Woodward
DE
EN
Manual 37427
CL2
4596
DST end month

Sommerzeitende Monat
{0}
{1o}
{1oc}
{2oc}
Adjust clock: DST end month
1 to 12
The month for the DST end date is configured here. Example:
1.................... 1st month of the year.
12.................. 12th month of the year.
Example: If daylight saving time starts at 2:00 am on the 2nd Sunday in March and ends at 2:00 am on the 1st
Sunday in November, the unit has to be configured like shown in Table 3-2 to enable an automatic change to
daylight saving time and back to standard time.
ID
4591
4594
4598
4592
4593
4597
4599
4595
4596
Parameter
DST begin time
DST begin weekday
DST begin nth weekday
DST begin month
DST end time
DST end weekday
DST end sunday
DST end month
Setting
On
2
Sunday
2nd
3
2
Sunday
1st
11
Table 3-2: Daylight saving time - configuration example
Year
2008
2009
2010
USA, Canada
DST Begins 2 a.m.
(Second Sunday in March)
March 9, 2008
March 8, 2009
March 14, 2010
DST Ends 3 a.m.

(First Sunday in November)
November 2, 2008
November 1, 2009
November 7, 2010
European Union
DST Begins 1 a.m. UTC=GMT
(Last Sunday in March)
March 30, 2008
March 29, 2009
March 28, 2010
DST Ends 2 a.m. UTC=GMT

(Last Sunday in October)
October 26, 2008
October 25, 2009
October 31, 2010
Table 3-3: Daylight saving time - examplary dates
Configure Display
The contrast and the brightness of the display may be adjusted using this screen.
Lamp Test
All lights on the controller may be tested for correct operation with this function.
Woodward
Page 29/339
Manual 37427
Enter Password
The easYgen-2000 Series utilizes a password protected multi-level configuration access hierarchy. This permits
varying degrees of access to the parameters being granted by assigning unique passwords to designated
personnel. A distinction is made between the access levels as follows:
Code level CL0 (User Level)
Standard password = none
This code level permits for monitoring of the system and limited access to the parameters. Configuration of the
control is not permitted. Only the parameters for setting the language, the date, the time, and the horn reset time
are accessible. The unit powers up in this code level.
Code level CL1 (Service Level)
Standard password = "0 0 0 1"
This code level entitles the user to change selected non-critical parameters, such as setting the parameters
accessible in CL0 plus Bar/PSI, C/F. The user may also change the password for level CL1. Access granted by
this password expires two hours after the password has been entered and the user is returned to the CL0 level.
Code level CL2 (Temporary Commissioning Level)
No standard password available
This code level grants temporary access to most of the parameters. The password is calculated from the random
number generated when the password is initially accessed. It is designed to grant a user one-time access to a
parameter without having to give him a reusable password. The user may also change the password for
level CL1. Access granted by this password expires two hours after the password has been entered and the user is
returned to the CL0 level. The password for the temporary commissioning level may be obtained from the
vendor.
Code level CL3 (Commissioning Level)
Standard password = "0 0 0 3"
This code level grants complete and total access to most of the parameters. In addition, the user may also change
the passwords for levels CL1, CL2 and CL3. Access granted by this password expires two hours after the
password has been entered and the user is returned to the CL0 level.
NOTE
Once the code level is entered, access to the configuration menus will be permitted for two hours or
until another password is entered into the control. If a user needs to exit a code level then code level,
CL0 should be entered. This will block unauthorized configuration of the control. A user may return to
CL0 by allowing the entered password to expire after two hours or by changing any one digit on the
random number generated on the password screen and entering it into the unit.
It is possible to disable expiration of the password by entering "0000" after the CL1 or CL3 password
has been entered. Access to the entered code level will remain enabled until another password is
entered. Otherwise, the code level would expire when loading the standard values (default 0000) via
ToolKit.
Parameter Table
Level
Text
Configure password
Password display
Code level display
Password for CAN interface 1
Code level CAN interface 1
Password for serial interface 1
Code level serial interface 1
Password for serial interface 2
Setting range
Default value
0 to 9999
(display only)
0 to 9999
(display only)
0 to 9999
(display only)
0 to 9999
(display only)
0 to 9999
(display only)
random number
0
random number
0
random number
0
random number
0
random number
0
Table 3-4: Configuration - standard values - enter password
Page 30/339
Woodward
Manual 37427
Figure 3-1 shows a configuration menu screen in code level CL0 (left) and CL1 (right).
DE
EN
Figure 3-1: Code level display
CL0
{0}
DE
EN
10400
CL0
10405
{0}
Password display
Passwort Display
{1o}
{1oc}
{2oc}
Code level display

Codeebene Display
{1o}
{1oc}
{2oc}
Password: Entry via front panel
The password for configuring the control via the front panel must be entered here.
Password system: Code level via display

Codeebene CAN Schnittstelle 1
CL0 {0} {1o} {1oc} {2oc}
10407
Password system: Code level via CAN interface #1

Passwort CAN Schnittstelle 2
CL0 {0} {1o} {1oc} {2oc}
Password: Entry via CAN interface #2

Codeebene CAN Schnittstelle 2
CL0 {0} {1o} {1oc} {2oc}
10422
Password system: Code level via CAN interface #2
DE
EN
Password: Entry via CAN interface #1
DE
EN
DE
EN
DE
EN
DE
EN
10432
CL0
DE
EN
10401
CL0
DE
EN
10406
CL0
DE
EN
10430
CL0
10420
Password for serial interface1

Passwort serielle Schnittst. 1
{0}
{1o}
{1oc}
{2oc}

Codeebene serielle Schnittst. 1
{0}
{1o}
{1oc}
{2oc}
Password for serial interface2

Passwort serielle Schnittst. 2
{0}
{1o}
{1oc}
{2oc}

Codeebene serielle Schnittst. 2
{0}
Woodward
{1o}
{1oc}
{2oc}
Info
This value displays the code level, which is currently enabled for access via the
front panel display.

Passwort CAN Schnittstelle 1
CL0 {0} {1o} {1oc} {2oc}
10402
0000 to 9999
0000 to 9999
The password for configuring the control via the CAN interface #1 must be
entered here.
Info
CAN interface #1s.
0000 to 9999
The password for configuring the control via the CAN interface #1 must be
entered here.
Info
CAN interface #1s.
Password: Entry via serial interface #1
0000 to 9999
The password for configuring the control via the serial interface #1 must be
entered here.
Password system: Code level via serial RS-232 interface #1
Info
This value displays the code level, which is currently enabled for access via RS232 serial interface #1.
Password: Entry via serial interface 2
0000 to 9999
The password for configuring the control via the serial interface #2 must be
entered here.
Password system: Code level via serial RS-485 interface #2
Info
This value displays the code level, which is currently enabled for access via RS485 serial interface #2.
Page 31/339
Manual 37427
System Management
Parameter Table
Level
Text
System managment
Device number
Configure display backlight
Time until backlight shutdown
Factory default settings
Reset factory default values
Start Bootloader
Clear eventlog
Setting range
Default value
1 to 32
On / Key activate.
1 to 999 min
Yes / No
Yes / No
23130 to 23130
Yes / No
1
Key activate.
120 min
No
No
42405
No
DE
EN
Table 3-5: Configuration - standard values - system management
CL2
1702
{0}
Device number
Gertenummer
{1o}
{1oc}
{2oc}
System parameter: Device address
1 to 32
A unique address is assigned to the control though this parameter. This unique
address permits the controller to be correctly identified on the CAN bus. The
address assigned to the controller may only be used once. All other bus addresses
are calculated on the number entered in this parameter. The device number is also
important for the device assignment in load sharing and load-depnedent start/stop.
NOTE
DE
EN
The unit must be restarted after changing the device number to ensure proper operation.
CL0
4556
Configure display backlight

Konfig. Display Beleuchtung
{0}
{1o}
{1oc}
{2oc}
DE
EN
Time until backlight shutdown

Zeit bis Abschaltung
CL2 {0} {1o} {1oc} {2oc}
4557
System parameter: Configure display backlight
On / Off / AUTO / Key activat.
On .................The display backlight is always enabled.

Off ................The display backlight is always disabled.
AUTO...........The display backlight is automatically switched off to save battery
energy, if no mains/busbar voltage is available.
Key activat. ..The display backlight will be dimmed, if no soft key is pressed for
the time configured in parameter 4557.
System parameter: Time until backlight shutdown
1 to 999 min
This parameter is only effective, if parameter 4556 is configured to "Key

activat.".
DE
EN
If no soft key has been pressed for the time configured here, the display backlight
will be dimmed.
CL0
1703
Factory default settings

Werkseinstellung
{0}
Page 32/339
{1o}
{1oc}
{2oc}
Factory settings: Restore default values
Yes / No
Yes ................The following three parameters are visible and restoring the
configured parameters to factory default values is enabled.
No .................The following three parameters are invisible and restoring the
configured parameters to factory default values is not enabled.
Woodward
Manual 37427
NOTE
DE
EN
The following parameters will only be displayed, if Factory Settings (parameter 1703) has been
configured to Yes and the enter button has been pressed.
CL0
{0}
DE
EN
1701
Reset factory default values

Standardwerte
CL2
10500
{0}
{1o}
{1oc}
{2oc}
Start Bootloader
Bootloader starten
{1o}
{1oc}
{2oc}
Factory settings: Set default values
Yes / No
Yes ............... All parameters, which the enabled access code grants priveleges to,
will be restored to factory default values.
No ................. All parameters will remain as currently configured.
Factory settings: Start Bootloader
00000
The bootloader is utilized for uploading application software only. The proper
enable code must be entered while the control is in access code level CL3 or higher
to perform this function.
DE
EN
Attention: This function is used for uploading application software and may only
be used by authorized Woodward technicians!
CL2
1706
Clear eventlog
Ereignisspeicher lschen
{0}
Woodward
{1o}
{1oc}
{2oc}
Factory settings: Clear event log
Yes / No
Yes ............... The event history will be cleared.

No ................. The event history will not be cleared.
Page 33/339
Manual 37427
System Management: Password System

Parameter Table
Level
Text
Password system
Basic code level
Commissioning code level
Temp. commissioning code level
Temp. supercomm. level code
Supercommissioning level code
Setting range
Default value
0 to 9999
0 to 9999
0 to 9999
0 to 9999
0 to 9999
Table 3-6: Configuration - standard values - system management: password system
NOTE
DE
EN
The following passwords grant varying levels of access to the parameters. Each individual password
can be used to access the appropriate configuration level through multiple access methods and
communication protocols (via the front panel, via serial RS-232/485 interface, and via the CAN bus).
CL1
DE
EN
10415
CL3
10413
{0}
Basic code level

Code Serviceebene
{1o}
{1oc}
{2oc}
Commissioning code level

Code Inbetriebnahme Ebene
{0}
{1o}
{1oc}
{2oc}
Password system: Password "Service Level" (CL1)
0000 to 9999
The password for the code level "Service" is defined in this parameter. Refer to
the Enter Password section on page 30 for default values.
Password system: Password "Commission" (CL3)
0000 to 9999
The password for the code level "Commission" is defined in this parameter.
Refer to the Enter Password section on page 30 for default values.
Password system: Password "Temporary Commission" (CL2)
Temp. supercomm. level code

Code temp. Supercomm. Ebene
{1o}
{1oc}
{2oc}
CL5 {0}
10412
Password system: Password "Temporary Supercommissioning" (CL4) 0000 to 9999
Supercommissioning level code

Code Supercommissioning Ebene
{1o}
{1oc}
{2oc}
CL5 {0}
10411
Password system: Password "Supercommissioning" (CL5)
DE
EN
DE
EN
DE
EN
Temp. commissioning code level

Code temp. Inbetriebn. Ebene
{1o}
{1oc}
{2oc}
CL3 {0}
10414
Page 34/339
0000 to 9999
The algorithm for calculating the password for the code level "Temporary
Commissioning" is defined in this parameter.
The algorithm for calculating the password for the code level "Temporary
Supercommissioning" is defined in this parameter.
0000 to 9999
The password for the code level "Supercommissioning" is defined in this

parameter. Refer to the Enter Password section on page 30 for default values.
Woodward
Manual 37427
Configuration
The configuration screen is accessed pressing the Configuration softkey on the Parameter screen. The following
sub-menus are available to configure the unit:
Configure Measurement
Configure Monitoring
Configure Application
Configure Interfaces
Configure LogicsManager
Configure Counters
NOTE
This controller is available in two different hardware version with either 1A [../1] or 5A [../5] current
transformer inputs. Both versions are discussed in this manual. The set points for specific parameters
will differ depending upon the hardware version.
NOTE
It is absolutely essential that correct rated values to be entered when configuring the controller, as
many measurement and monitoring functions refer to these values.
Woodward
Page 35/339
Manual 37427
Configure Measurement
Parameter Table
Level
Text
Configure measurement
Show mains data
Generator type
System rated frequency
Engine rated speed
Generator rated voltage
Mains rated voltage
Busbar 1 rated voltage
Gen. rated active power [kW]
Gen. rated react. power [kvar]
Generator rated current
Mains rated active power [kW]
Mains rated react. pwr. [kvar]
Mains rated current
1Ph2W voltage measuring
1Ph2W phase rotation
Generator voltage measuring
Generator current measuring
Mains voltage measuring
Mains current input
Mains current measuring
Setting range
Default value
Yes / No
Synchron / Asynchron
50 / 60 Hz
500 to 4000 rpm
50 to 650000 V
50 to 650000 V
50 to 650000 V
0.5 to 99999.9 kW
0.5 to 99999.9 kvar
1 to 32000 A
0.5 to 99999.9 kW
0.5 to 99999.9 kvar
5 to 32000 A
Phase - phase / Phase - neutral
CW /CCW
3Ph 4W / 3Ph 3W /
1Ph 2W / 1Ph 3W
L1 L2 L3 / Phase L1 /
Phase L2 / Phase L3
3Ph 4W / 3Ph 3W /
1Ph 2W / 1Ph 3W
Mains current / Ground current /
Off
Phase L1 / Phase L2 / Phase L3
Yes
Synchron
50 Hz
1500 rpm
400 V
400 V
400 V
200 kW
200 kvar
300 A
200 kW
200 kvar
300 A
Phase phase
CW
3Ph 4W
L1 L2 L3
3Ph 4W
Mains current
Phase L1
Table 3-7: Measurement - standard values - configure measurement
NOTE
If the easYgen is intended to be operated in parallel with the mains, the mains voltage measuring
inputs must be connected. If an external mains decoupling is performed, jumpers between busbar and
mains voltage measuring inputs may be installed.
Page 36/339
Woodward
DE
EN
Manual 37427
CL2
235
{0}
{1o}
Generator type
Generatortyp
{1oc}
{2oc}
Generator type
Synchron / Asynchron
The easYgen supports two types of generators:

synchron generators
asynchron generators (induction generators)
Synchron: The unit provides all functions which are needed for synchron
generator applications. Isolated and mains parallel operation is supported.
Asynchron: The unit provides the special function of the asynchronos generator
with:
The speed is regulated with the speed signal from the MPU or
J1939/CAN input (as long as the GCB is open).
The closing of the GCB is executed, if the speed is within the
corresponding frequency range of the generator operating window. The
voltage and phase angle is ignored in this case.
The generator monitoring (under/over frequency and under/overvoltage)
is switched off, until the generator breaker is closed.
After opening the GCB, under/over frequency and under/overvoltage
monitoring is switched off again.
The Frequency/MPU speed plausibility monitoring is only active, if the
GCB is closed.
The synchronoscope is not displayed in the asynchron modus.
The asynchron modus is normally used in mains parallel operation. Please

consider the following settings:
Application mode (3401) = GCB/MCB

MCB control (5733) = Off
Mains decoupling (3110) = GCB
Emergency run (2802) = Off
MPU input (1600) = On
Generator operating frequency (5802, 5803)
DE
EN
Figure 3-2: Configure measurement - generator type selection
CL2
{0}
DE
EN
1750

Nennfrequenz im System
CL2
1601
{0}
Woodward
{1o}
{1oc}
{2oc}
Engine rated speed

Nenndrehzahl
{1o}
{1oc}
{2oc}
50 / 60 Hz
The rated frequency of the system is used as a reference figure for all frequency
related functions, which use a percentage value, like frequency monitoring,
breaker operation windows or the Analog Manager.
Engine rated speed
500 to 4,000 RPM
Number of revolutions per minute of the engine at rated engine speed. The speed
control with an ECU via J1939 CAN bus refers to this value.
Page 37/339
DE
EN
Manual 37427
CL2
1766

Nennspannung Generator
{0}
{1o}
{1oc}
{2oc}
50 to 650000 V
This value refers to the rated voltage of the generator (generator voltage
on data plate) and is the voltage measured on the potential transformer
primary.
DE
EN
The generator potential transformer primary voltage is entered in this parameter.

The generator rated voltage is used as a reference figure for all generator voltage
related functions, which use a percentage value, like generator voltage
monitoring, breaker operation windows or the Analog Manager.
CL2
1768
{0}
---
Mains rated voltage

Nennspannung Netz
{1o}
---
{1oc}
---
{2oc}
Mains rated voltage
50 to 650000 V
This value refers to the rated voltage of the mains and is the voltage
measured on the potential transformer primary.
The mains potential transformer primary voltage is entered in this parameter. The
mains rated voltage is used as a reference figure for all mains voltage related
functions, which use a percentage value, like mains voltage monitoring, breaker
operation windows or the Analog Manager.
DE
EN

Sammelschiene 1 Nennspannung
{1o}
{1oc} {2oc}
CL2 {0}
1781
50 to 650000 V
This value refers to the rated voltage of busbar 1 and is the voltage
measured on the potential transformer primary.
If voltage measuring is configured to 1Ph 3W, the WYE voltage (VL1N)
must be entered here.
DE
EN
The busbar 1 potential transformer primary voltage is entered in this parameter.

The busbar rated voltage is used as a reference figure for all busbar voltage
related functions, which use a percentage value, like synchronization.
CL2
1752
Gen. rated active power [kW]

Nennwirkleistung [kW]
{0}
{1o}
{1oc}
{2oc}
DE
EN
DE
EN
Gen. rated react. power [kvar]

Nennblindleistung [kvar]
CL2 {0} {1o} {1oc} {2oc}
1758
CL2
1754

Nennstrom Generator
{0}
{1o}
{1oc}
{2oc}
DE
EN
Mains rated active power [kW]

Nennwirkleistung Netz [kW]
CL2 {0} {1o} {1oc} {2oc}
1748
Page 38/339
Generator rated active power
0.5 to 99999.9 kW
This value specifies the generator real power rating, which is used as a reference
figure for related functions. The generator rated active power is the generator
apparent power multiplied by the generator power factor (typically ~0.8). These
values are indicated in the generator data plate. Refer to Figure 3-3 for more
information.
Generator rated reactive power
0.5 to 99999.9 kvar
This value specifies the generator reactive power rating, which is used as a
reference figure for related functions. The generator rated reactive power also
depends on the generator values. Refer to Figure 3-3 for more information.
1 to 32000 A
This value specifies the generator rated current, which is used as a reference figure
for related functions.
Mains rated active power
0.5 to 99999.9 kW
This value specifies the mains real power rating, which is used as a reference
figure for related functions. The mains rated active power is a reference value used
by several monitoring and control functions. Refer to Figure 3-3 for more
information.
Woodward
Manual 37427
DE
EN
DE
EN
Mains rated react. pwr. [kvar]

Nennblindleistung Netz [kvar]
CL2 {0} {1o} {1oc} {2oc}
1746
CL2
1785
{0}
Mains rated current

Nennstrom Netz
{1o}
{1oc}
{2oc}
Mains rated reactive power
0.5 to 99999.9 kvar
This value specifies the mains reactive power rating, which is used as a reference
figure for related functions. The mains rated reactive power is a reference value
used by several monitoring and control functions. Refer to Figure 3-3 for more
information.
Mains rated current
5 to 32000 A
This value specifies the mains rated current, which is used as a reference figure for
related functions.
Figure 3-3 shows the AC power triangle to illustrate the dependencies between active power, apparent power,
reactive power, and power factor.
PF = Power Factor
P = Active Power = [kW]
S = Apparent power [kVA]
Q = Reactive Power [kvar]
PF =
P
= cos
S
Q = S 2 P2
S = P2 + Q2
P = S * PF
DE
EN
Figure 3-3: AC power triangle
CL3
1858
1Ph2W voltage measuring

Art der 1Ph2W Messung
{0}
{1o}
{1oc}
{2oc}
Measurement principle: 1Ph 2W measuring
Please refer to the comments on measuring principles in the installation

manual (37426).
Phase - phase The unit is configured for measuring phase-phase voltages if 1Ph
2W measuring is selected.
Phase - neutral The unit is configured for measuring phase-neutral voltages if 1Ph
2W measuring is selected.
NOTE
Do never configure the busbar measurement for phase-neutral, if the other systems like mains and
generator are configured as 3Ph 3W or 4Ph 4W. The phase angle for synchronisation would be not
correct.
DE
EN
1Ph2W phase rotation

Art der 1Ph2W Drehrichtung
CL3 {0} {1o} {1oc} {2oc}
1859
Measurement principle: 1Ph 2W phase rotation
CW / CCW

manual (37426).
CW ............... A clockwise rotation field is considered for 1Ph 2W measuring .
CCW ............ A counter-clockwise rotation field is considered for 1Ph 2W
measuring.
Woodward
Page 39/339
Manual 37427
DE
EN
Generator voltage measuring

Gen.Spannungsmessung
CL2 {0} {1o} {1oc} {2oc}
1851
Measurement principle: Generator
3Ph 4W / 3Ph 3W / 1Ph 2W / 1Ph 3W

manual (37426).
3Ph 4W ........Measurement is performed Line-Neutral (WYE connected system)
and Line-Line (Delta connected system). The protection depends on
the setting of parameter 1770 on page 47. Phase voltages and the
neutral must be connected for proper calculation. Measurement,
display and protection are adjusted according to the rules for WYE
connected systems. Monitoring refers to the following voltages:
VL12, VL23, and VL31 (parameter 1770 configured to "Phase-phase")
VL1N, VL2N, and VL3N (parameter 1770 configured to "Phaseneutral")
3Ph 3W ........Measurement is performed Line-Line (Delta connected system).
Phase voltages must be connected for proper calculation.
Measurement, display and protection are adjusted according to the
rules for Delta connected systems. Monitoring refers to the following
voltages:
VL12, VL23, VL31
1Ph 2W ........Measurement is performed Line-Neutral (WYE connected system) if
parameter 1858 is configured to "Phase - neutral" and Line-Line
(Delta connected system) if parameter 1858 is configured to "Phase phase". Measurement, display and protection are adjusted according
to the rules for phase-phase systems. Monitoring refers to the
following voltages:
VL1N, VL12
1Ph 3W ........Measurement is performed Line-Neutral (WYE connected system)
the setting of parameter 1770 on page 47. Measurement, display, and
protection are adjusted according to the rules for single-phase
systems. Monitoring refers to the following voltages:
VL1N, VL3N (parameter 1770 configured to "Phase-phase")
VL13 (parameter 1770 configured to "Phase-neutral")
NOTE: If this parameter is configured to 1Ph 3W, the generator and
mains rated voltages (parameters 1766 and 1768) must be entered as
Line-Line (Delta) and the busbar 1 rated voltage (parameter 1781)
must be entered as Line-Neutral (WYE).
DE
EN
Generator current measuring

Gen.Strommessung
CL2 {0} {1o} {1oc} {2oc}
1850
Measurement principle: Generator
L1 L2 L3 / Phase L1 / Phase L2 / Phase L3

manual (37426). This parameter is only effective if generator voltage
measuring (parameter 1851) is configured to "3Ph 4W" or "3Ph 3W".
L1 L2 L3 ......All three phases are monitored. Measurement, display and protection
are adjusted according to the rules for 3-phase measurement.
Monitoring refers to the following currents:
IL1, IL2, IL3
Phase L{1/2/3} Only one phase is monitored. Measurement, display and
measurement. Monitoring refers to the selected phase.
Page 40/339
Woodward
DE
EN
Manual 37427
CL2
1853
Mains voltage measuring

Netz.Spannungsmessung
{0}
{1o}
---
---
{1oc}
---
{2oc}
Measurement principle: Mains
3Ph 4W / 3Ph 3W / 1Ph 2W / 1Ph 3W

manual (37426).
3Ph 4W ........ Measurement is performed Line-Neutral (WYE connected system)
the setting of parameter 1771 on page 83. Phase voltages and the
neutral must be connected for proper calculation. Measurement,
display and protection are adjusted according to the rules for WYE
connected systems. Monitoring refers to the following voltages:
VL12, VL23, and VL31 (parameter 1771 configured to "Phase-phase")
VL1N, VL2N and VL3N (parameter 1771 configured to "Phaseneutral")
3Ph 3W ........ Measurement is performed Line-Line (Delta connected system).
Phase voltages must be connected for proper calculation.
Measurement, display and protection are adjusted according to the
rules for Delta connected systems. Monitoring refers to the following
voltages:
VL12, VL23, VL31
1Ph 2W ........ Measurement is performed Line-Neutral (WYE connected system) if
parameter 1858 is configured to "Phase - neutral" and Line-Line
(Delta connected system) if parameter 1858 is configured to "Phase phase". Measurement, display and protection are adjusted according
to the rules for phase-phase systems. Monitoring refers to the
following voltages:
VL1N, VL12
1Ph 3W ........ Measurement is performed Line-Neutral (WYE connected system)
the setting of parameter 1771 on page 83. Measurement, display, and
systems. Monitoring refers to the following voltages:
VL1N, VL3N (parameter 1771 configured to "Phase-phase")
VL13 (parameter 1771 configured to "Phase-neutral")
NOTE: If this parameter is configured to 1Ph 3W, the generator and
mains rated voltages (parameters 1766 and 1768) must be entered as
Line-Line (Delta) and the busbar 1 rated voltage (parameter 1781)
must be entered as Line-Neutral (WYE).
DE
EN
Mains current input

Eingang Netzstrom
CL2
DE
EN
1854
CL2
1852
Mains current measuring

Netz.Strommessung
{0}
---
{1o}
---
{1oc}
---
{2oc}
Measurement principle: Mains current input
Off / Mains current / Ground current
This parameter configures whether ground or mains current is measured on

terminals 1/2 or the input is disabled.
Measurement principle: Mains
Phase L1 / Phase L2 / Phase L3

manual (37426). This parameter is only effective if mains voltage
measuring (parameter 1853) is configured to "3Ph 4W" or "3Ph 3W".
Phase L{1/2/3} Measurement is performed for the selected phase only. The
measurement and display refer to the selected phase. The configured
phase CT must be connected to perform current measurement.
Woodward
Page 41/339
Manual 37427
Configure Measurement: Configure Transformer

Parameter Table
Level
Text
Configure transformer
Gen. PT primary rated voltage
Gen. PT secondary rated volt.
Gen. CT primary rated current
Busb1 PT primary rated voltage
Busb1 PT secondary rated volt.
Mains PT primary rated voltage
Mains PT secondary rated volt.
Mains CT primary rated current
Gnd. CT primary rated current
Setting range
Default value
50 to 650000 V
50 to 480 V
1 to 32000 A
50 to 650000 V
50 to 650000 V
50 to 650000 V
50 to 480 V
1 to 32000 A
1 to 32000 A
400 V
400 V
500 A
400 V
400 V
400 V
400 V
500 A
500 A
Table 3-8: Measurement - standard values - configure transformer
Generator
DE
EN
Gen. PT primary rated voltage

Gen.Spg.Wandler primr
CL2 {0} {1o} {1oc} {2oc}
1801
Generator potential transformer primary voltage rating
50 to 650000 V
Some generator applications may require the use of potential transformers to

facilitate measuring the voltages produced by the generator. The rating of the
primary side of the potential transformer must be entered into this parameter.
If the generator application does not require potential transformers (i.e. the
generated voltage is 480 V or less), then the generated voltage will be entered into
this parameter.
DE
EN
Gen. PT secondary rated volt.

Gen.Spg.Wandler sekundr
CL2 {0} {1o} {1oc} {2oc}
1800
Generator potential transformer secondary voltage rating
50 to 480 V
The control is equipped with dual voltage measuring inputs. The voltage
range of these measurement inputs is dependent upon input terminals are
used (see below). This value refers to the secondary voltages of the
potential transformers, which are directly connected to the control.
Some generator applications may require the use of potential transformers to
facilitate measuring the voltages produced by the generator. The rating of the
secondary side of the potential transformer must be entered into this parameter.
If the generator application does not require potential transformers (i.e. the
generated voltage is 480 V or less), then the generated voltage will be entered into
this parameter.
Rated voltage: 100 Vac (this parameter configured between 50 and 130 V)
- Generator voltage: Terminals 14/16/18/20
- Generator voltage: Terminals 15/17/19/21
!
WARNING:
Only connect the measured voltage to either the 100 Vac or the 400 Vac
inputs. Do not connect both sets of inputs to the measured system.
NOTE
This controller is available in two different hardware version with either 1A [../1] or 5A [../5] current
transformer inputs. Both versions are discussed in this manual. The set points for specific parameters
will differ depending upon the hardware version, indicated on the data plate.
[1]
easYgen-2xxx-1 = Current transformer with ../1 A rated current
[5]
easYgen-2xxx-5 = Current transformer with ../5 A rated current
Page 42/339
Woodward
Manual 37427
DE
EN
Gen. CT primary rated current

Generator Stromwandler
CL2 {0} {1o} {1oc} {2oc}
1806
Generator current transformer primary rating
1 to 32000/5 A
This screen only applies to controls equipped with 5 A CT inputs. This will
not be displayed in the controller screen of a unit equipped with 1 A CT
inputs.
The input of the current transformer ratio is necessary for the indication and
control of the actual monitored value. The current transformers ratio should be
selected so that at least 60% of the secondary current rating can be measured when
the monitored system is at 100% of operating capacity (i.e. at 100% of system
capacity a 5 A CT should output 3 A). If the current transformers are sized so that
the percentage of the output is lower, the loss of resolution may cause inaccuracies
in the monitoring and control functions and affect the functionality of the control.
Woodward
Page 43/339
Manual 37427
Busbar
DE
EN
Busb1 PT primary rated voltage

Sams. 1 Spg.Wandler primr
{1o}
{1oc} {2oc}
CL2 {0}
1813
Busbar 1 potential transformer primary voltage rating
50 to 650000 V
Some applications may require the use of potential transformers to facilitate

measuring the voltages to be monitored. The rating of the primary side of the
potential transformer must be entered into this parameter.
If the application does not require potential transformers (i.e. the measured
voltage is 480 V or less), then the measured voltage will be entered into this
parameter.
DE
EN
Busb1 PT secondary rated volt.

Sams.1 Spg.Wandler sekundr
{1o}
{1oc} {2oc}
CL2 {0}
1812
Busbar 1 potential transformer secondary voltage rating
50 to 480 V
measuring the busbar voltages. The rating of the secondary side of the potential
transformer must be entered into this parameter.
parameter.
- Busbar voltage: Terminals 22/24/26/28
- Busbar voltage: Terminals 23/25/27/29
!
Page 44/339
WARNING:
Woodward
Manual 37427
Mains PT
DE
EN
Mains PT primary rated voltage

Netz.Spg.Wandler primr
{1o}
{1oc} {2oc}
CL2 {0}
------1804
Mains potential transformer primary voltage rating
50 to 650000 V

measuring the voltages to be monitored. The rating of the primary side of the
potential transformer must be entered into this parameter.
parameter.
DE
EN
Mains PT secondary rated volt.

Netz.Spg.Wandler sekundr
{1o}
{1oc} {2oc}
CL2 {0}
------1803
Mains potential transformer secondary voltage rating
50 to 480 V
measuring the mains voltages. The rating of the secondary side of the potential
transformer must be entered into this parameter.
parameter.
- Mains voltage: Terminals 22/24/26/28
- Mains Voltage: Terminals 23/25/27/29
!
WARNING:
Mains Current Transformer

DE
EN
Mains CT primary rated current

Netz Stromwandler
{1o}
{1oc} {2oc}
CL2 {0}
------1807
Mains current transformer primary rating
1 to 32000/5 A
This screen only applies to controls equipped with 5 A CT inputs. This

will not be displayed in the controller screen of a unit equipped with 1 A
CT inputs.
This screen is only visible if parameter 1854 is configured as Mains.
selected so that at least 60% of the secondary current rating can be measured
when the monitored system is at 100% of operating capacity (i.e. at 100% of
system capacity a 5 A CT should output 3 A). If the current transformers are
sized so that the percentage of the output is lower, the loss of resolution may
cause inaccuracies in the monitoring and control functions and affect the
functionality of the control.
Woodward
Page 45/339
Manual 37427
Ground Current Transformer

DE
EN
Gnd. CT primary rated current

Erd-Stromwandler
{1o}
{1oc} {2oc}
CL2 {0}
1810
Ground current transformer primary rating
1 to 32000/5 A
This screen only applies to controls equipped with 5 A CT inputs. This

will not be displayed in the controller screen of a unit equipped with 1 A
CT inputs.
This screen is only visible if parameter 1854 is configured as Ground.
selected so that at least 60% of the secondary current rating can be measured
when the monitored system is at 100% of operating capacity (i.e. at 100% of
system capacity a 5 A CT should output 3 A). If the current transformers are
sized so that the percentage of the output is lower, the loss of resolution may
cause inaccuracies in the monitoring and control functions and affect the
functionality of the control.
Page 46/339
Woodward
Manual 37427
Configure Monitoring
Configure Monitoring: Generator

Parameter Table
Level
Text
Configure generator monitoring
Generator voltage monitoring
Setting range
Default value
Phase - phase
Table 3-9: Monitoring - standard values - configure generator monitoring
DE
EN
Generator voltage monitoring

Gen. Spannungsberwachung
CL2 {0} {1o} {1oc} {2oc}
1770
Generator protection: type of monitoring
The unit can either monitor the phase-neutral (wye) voltages or the phase-phase
(delta) voltages. If the controller is used in a compensated or isolated network,
voltage protection monitoring should be configured as phase-neutral to prevent
earth-faults resulting in tripping of the voltage protections.
!
WARNING:
This parameter defines how the protective functions operate.
Phase - phase The phase-phase voltage will be measured and all subsequent
parameters concerning voltage monitoring "generator" are referred to
this value (VL-L).
Phase - neutral The phase-neutral voltage will be measured and all subsequent
parameters concerning voltage monitoring "generator" are referred to
this value (VL-N).
Woodward
Page 47/339
Manual 37427
Configure Monitoring: Generator, Operating Voltage / Frequency

Parameter Table
Level
Text
Configure generator operating voltage / frequency
Upper voltage limit
Lower voltage limit
Upper frequency limit
Lower frequency limit
Setting range
Default value
100 to 150 %
50 to 100 %
100.0 to 150.0 %
50.0 to 100.0 %
110 %
90 %
110 %
90 %
DE
EN
Table 3-10: Monitoring - standard values - configure generator operating voltage / frequency
CL2
DE
EN
5800
CL2
{0}
{0}
{0}
5803
{1oc}
{2oc}
{0}
{1oc}
{2oc}

Obere Frequenzabw.
{1o}
DE
CL2
{1o}
EN
5802
Lower voltage limit

Untere Spannungsabw.
DE
CL2
{1o}
EN
5801
Upper voltage limit

Obere Spannungsabw.
{1oc}
{2oc}

Untere Frequenzabw.
{1o}
{1oc}
{2oc}
Generator maximum operating voltage limit
100 to 150 %
The maximum permissible positive deviation of the generator voltage from the
generator rated voltage (parameter 1766 on page 38) is configured here. This value
may be used as a voltage limit switch. The conditional state of this switch may be
used as a command variable for the LogicsManager (02.03).
Generator minimum operating voltage limit
50 to 100 %
The maximum permissible negative deviation of the generator voltage from the
generator rated voltage (parameter 1766 on page 38) is configured here. This value
may be used as a voltage limit switch. The conditional state of this switch may be
Generator maximum operating frequency limit
100.0 to 150.0 %
The maximum permissible positive deviation of the generator frequency from the
rated system frequency (parameter 1750 on page 37) is configured here. This value
may be used as a frequency limit switch. The conditional state of this switch may
be used as a command variable for the LogicsManager (02.04).
Generator minimum operating frequency limit
50.0 to 100.0 %
The maximum permissible negative deviation of the generator frequency from the
NOTE
The operating voltage/frequency parameters are used to check if the values are in range when
performing a dead bus closure and synchronization of the generator. Busbar must be within this
ranges to synchronize the generator to the busbar.
It is recommended to configure the operating limits within the monitoring limits.
Page 48/339
Woodward
Manual 37427
Configure Monitoring: Generator, Overfrequency (Levels 1 & 2) ANSI# 81O

This controller provides the user with two alarm levels for generator overfrequency. Both alarms are definite time
alarms and are illustrated in the figure below. The figure diagrams a frequency trend and the associated pickup
times and length of the alarms. Monitoring for overfrequency faults is performed in two steps.
If this protective function is triggered, the display indicates "Gen. overfrequency 1" or
"Gen. overfrequency 2" and the logical command variable "06.01" or "06.02" will be enabled.
Refer to Appendix E: Triggering Characteristics, Figure 3-37 on page 322 for the triggering characteristic of this
monitoring function.
Parameter table
Level
Text
Overfrequency (the hysteresis is 0.05 Hz.)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Delayed by engine speed
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
The parameter limits

represented in this table have
identical permissible ranges.
Each parameter may be
configured with different
settings to create unique trip
characteristics for specific
thresholds.
Setting range
Default value
On / Off
50.0 to 130.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
50.0 to 130.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
110.0 %
1.50 s
B
No
No
On
115.0 %
0.30 s
F
No
No
DE
EN
Table 3-11: Monitoring - standard values - generator overfrequency
CL2
{0}
{1o}
DE
EN
1900
1906
CL2
1904
1910
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen.Overfrequency: Monitoring (Level 1/Level 2)
On / Off
On ................ Overfrequency monitoring is carried out according to the following

parameters. Monitoring is performed at two levels. Both values may
be configured independent from each other (prerequisite: Level 1
limit < limit 2).
Off ............... Monitoring is disabled for Level 1 limit and/or Level 2 limit.
Gen.Overfrequency: Threshold value (Level 1/Level 2)
50.0 to 130.0 %
This value refers to the System rated frequency (parameter 1750 on

page 37).
DE
EN
The percentage values that are to be monitored for each threshold limit are defined
here. If this value is reached or exceeded for at least the delay time without
interruption, the action specified by the alarm class is initiated.
CL2
{0}
{1o}
DE
EN
1905
1911
CL2
1901
1907
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen.Overfrequency: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator frequency value exceeds the threshold value for the
delay time configured here, an alarm will be issued. If the monitored generator
frequency falls below the threshold (minus the hysteresis) before the delay expires
the time will be reset.
Gen.Overfrequency: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F
See chapter "Alarm" on page 269.

Each limit may be assigned an independent alarm class that specifies what action
should be taken when the limit is surpassed.
Page 49/339
DE
EN
Manual 37427
CL2
1902
1908
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

Verzgert durch Motordrehzahl
{1o}
{1oc} {2oc}
CL2 {0}
1903
1909
Page 50/339
Gen. overfrequency: Self acknowledgment (Level 1/Level 2)
Yes / No
Yes ................The control automatically clears the alarm if the fault condition is
no longer detected.
No .................The control does not automatically reset the alarm when the fault
condition is no longer detected. The alarm must be acknowledged
and reset by manually pressing the appropriate buttons or by
activating the LogicsManager output "External acknowledgement"
(via a discrete input or via an interface).
Gen. overfrequency Engine delayed monitoring (Level 1/Level 2)
Yes / No
Yes ................Monitoring for fault conditions is not performed until engine

delayed monitoring is enabled. The engine monitoring delay time
(parameter 3315 on page 184) must expire prior to fault monitoring
being enabled for parameters assigned this delay.
No .................Monitoring for this fault condition is continuously enabled
regardless of engine speed.
Woodward
Manual 37427
Configure Monitoring: Generator, Underfrequency (Levels 1 & 2) ANSI# 81U

This controller provides the user with two alarm levels for generator underfrequency. Both alarms are definite
time alarms and are illustrated in the figure below. The figure diagrams a frequency trend and the associated
pickup times and length of the alarms. Monitoring for underfrequency faults is performed in two steps.
If this protective function is triggered, the display indicates "Gen.underfrequency 1" or
"Gen.underfrequency 2" and the logical command variable "06.03" or "06.04" will be enabled.
Parameter table
Level
Text
Underfrequency (the hysteresis is 0.05 Hz.)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment

thresholds.
Setting range
Default value
On / Off
50.0 to 130.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
50.0 to 130.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
90.0 %
5.00 s
B
No
Yes
On
84.0 %
0.30 s
F
No
Yes
DE
EN
Table 3-12: Monitoring - standard values - generator underfrequency
CL2
{0}
{1o}
DE
EN
1950
1956
CL2
1954
1960
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. underfrequency: Monitoring (Level 1/Level 2)
On / Off
On ................ Underfrequency monitoring is carried out according to the

following parameters. Monitoring is performed at two levels. Both
values may be configured independent from each
other (prerequisite: Level 1 > Level 2).
Gen. underfrequency: Threshold value (Level 1/Level 2)
50.0 to 130.0 %
This value refers to the System rated frequency (parameter 1750 on

page 37).
DE
EN
here. If this value is reached or fallen below for at least the delay time without
CL2
{0}
{1o}
DE
EN
1955
1961
CL2
1951
1957
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. underfrequency: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator frequency value falls below the threshold value for the
frequency exceeds the threshold (plus the hysteresis) again before the delay
expires the time will be reset.
Gen. underfrequency: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

Page 51/339
DE
EN
Manual 37427
CL2
1952
1958
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
1953
1959
Gen. underfrequency: Self acknowledgment (Level 1/Level 2)
Yes / No
Yes................ The control automatically clears the alarm if the fault condition is
no longer detected.
No ................. The control does not automatically reset the alarm when the fault
Gen. underfrequency Engine delayed monitoring (Limit 1/Limit 2)
Yes / No
Yes................ Monitoring for fault conditions is not performed until engine

No ................. Monitoring for this fault condition is continuously enabled
NOTE
This monitoring function is disabled when the idle mode (see page 187) is active.
Page 52/339
Woodward
Manual 37427
Configure Monitoring: Generator, Overvoltage (Levels 1 & 2) ANSI# 59

Voltage is monitored according to how the parameter "Generator voltage measuring" (parameter 1851 on
page 40) is configured. This controller provides the user with two alarm levels for generator overvoltage. Both
alarms are definite time alarms and are illustrated in the figure below. The figure diagrams a frequency trend and
the associated pickup times and length of the alarms. Monitoring for overvoltage faults is performed in two steps.
If this protective function is triggered, the display indicates "Gen. overvoltage 1" or
"Gen. overvoltage 2" and the logical command variable "06.05" or "06.06" will be enabled.
Parameter table
Level
Text
Overvoltage (the hysteresis is 0.7 % of the rated value)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment

thresholds.
Setting range
Default value
On / Off
50.0 to 125.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
50.0 to 125.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
108.0 %
5.00 s
B
No
No
On
112.0 %
0.30 s
F
No
No
DE
EN
Table 3-13: Monitoring - standard values - generator overvoltage
CL2
{0}
{1o}
DE
EN
2000
2006
CL2
2004
2010
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. overvoltage: Monitoring (Level 1/Level 2)
On / Off
On ................ Overvoltage monitoring is carried out according to the following

limit < Level 2 limit).
Off ................ Monitoring is disabled for Level 1 limit and/or Level 2 limit.
Gen. overvoltage: Threshold value (Level 1/Level 2)
50.0 to 125.0 %
This value refers to the Generator rated voltage (parameter 1766 on

page 38).
DE
EN
CL2
{0}
{1o}
DE
EN
2005
2011
CL2
2001
2007
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. overvoltage: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator voltage exceeds the threshold value for the delay time
configured here, an alarm will be issued. If the monitored generator voltage falls
below the threshold (minus the hysteresis) before the delay expires the time will
be reset.
Gen. overvoltage: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

Page 53/339
DE
EN
Manual 37427
CL2
2002
2008
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2003
2009
Page 54/339
Gen. overvoltage: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Gen. overvoltage: Engine delayed monitoring (Level 1/Level 2)
Yes / No

Woodward
Manual 37427
Configure Monitoring: Generator, Undervoltage (Levels 1 & 2) ANSI# 27

Voltage is monitored according to how the parameter "Generator voltage measuring" (parameter 1851 on
page 40) is configured. This controller provides the user with two alarm levels for generator overvoltage. Both
alarms are definite time alarms and are illustrated in the figure below. The figure diagrams a frequency trend and
the associated pickup times and length of the alarms. Monitoring for undervoltage faults is performed in two
steps.
If this protective function is triggered, the display indicates "Gen. undervoltage 1" or
"Gen. undervoltage 2" and the logical command variable "06.07" or "06.08" will be enabled.
Parameter table
Level
Text
Undervoltage (the hysteresis is 0.7 % of the rated value)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment

thresholds.
Setting range
Default value
On / Off
50.0 to 125.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
50.0 to 125.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
92.0 %
5.00 s
B
No
Yes
On
88.0 %
00.30 s
F
No
Yes
DE
EN
Table 3-14: Monitoring - standard values - generator undervoltage
CL2
{0}
{1o}
DE
EN
2050
2056
CL2
2054
2060
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. undervoltage: Monitoring (Level 1/Level 2)
On / Off
On ................ Undervoltage monitoring is carried out according to the following

parameters. Monitoring is performed at two levels. Both values
may be configured independent from each other (prerequisite:
Level 1 limit < Level 2 limit).
Gen. undervoltage: Threshold value (Level 1/Level 2)
50.0 to 125.0 %
This value refers to the Generator rated voltage (parameter 1766 on

page 38).
DE
EN
The percentage values that are to be monitored for each threshold limit are
defined here. If this value is reached or fallen below for at least the delay time
without interruption, the action specified by the alarm class is initiated.
CL2
2055
2061
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Gen. undervoltage: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator voltage falls below the threshold value for the delay
time configured here, an alarm will be issued. If the monitored generator voltage
exceeds the threshold (plus the hysteresis) again before the delay expires the time
will be reset.
Page 55/339
DE
EN
Manual 37427
CL2
{0}
{1o}
2052
2058
{2oc}
Self acknowledge
Selbstquittierend
DE
CL2
{1oc}
Gen. undervoltage: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

EN
2051
2057
Alarm class
Alarmklasse
{0}
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2053
2059
Gen. undervoltage: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Gen. undervoltage: Delayed engine speed (Level 1/Level 2)
Yes / No

NOTE
This monitoring function is disabled when the idle mode (see page 187) is active.
Page 56/339
Woodward
Manual 37427
Configure Monitoring: Generator, Time-Overcurrent Monit. (Levels 1, 2 & 3) ANSI# 50/51

Current is monitored according to how the parameter "Generator current measuring" (parameter 1850 on page 40)
is configured. This controller provides the user with three definite time alarm levels for generator overcurrent
faults and may be setup as illustrated in the figure below. Monitoring of the maximum phase current is performed
in three steps. Every step can be provided with a delay time independent of the other steps.
If this protective function is triggered, the display indicates "Gen. overcurrent 1",
"Gen. overcurrent 2", or "Gen. overcurrent 3" and the logical command variable "06.09",
"06.10.", or "06.11" will be enabled.
Parameter table
thresholds.
Level
Text
Overcurrent (the hysteresis is 1 % of the rated value)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 3
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
50.0 to 300.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
On / Off
50.0 to 300.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
On / Off
50.0 to 300.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
On
110.0 %
30.00 s
E
No
On
150.0 %
1.00 s
F
No
On
250.0 %
0.40 s
F
No
DE
EN
Table 3-15: Monitoring - standard values - generator time-overcurrent
CL2
{0}
{1o}
DE
EN
2200
2206
2212
CL2
2204
2210
2216
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. overcurrent, TOC: Monitoring (Level 1/Level 2/Level 3)
On / Off
On ................ Overcurrent monitoring is carried out according to the following

parameters. Monitoring is performed at three levels. All three values
may be configured independent from each other (prerequisite:
Level 1 < Level 2 < Level 3).
Off ................ Monitoring is disabled for Level 1 limit, Level 2 limit, and/or Level 3
limit.
Gen. overcurrent, TOC: Threshold value (Level 1/Level 2/Level 3)
50.0 to 300.0 %
This value refers to the Generator rated current (parameter 1754 on

page 38).
DE
EN
CL2
2205
2211
2217
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Gen. overcurrent, TOC: Delay (Level 1/Level 2/Level 3)
0.02 to 99.99 s
If the monitored generator current exceeds the threshold value for the delay time
configured here, an alarm will be issued. If the monitored generator current falls
below the threshold (minus the hysteresis) before the delay expires the time will be
reset.
Page 57/339
DE
EN
Manual 37427
CL2
{0}
DE
CL2
2202
2208
2214
{1o}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. overcurrent, TOC: Alarm class (Level 1/Level 2/Level 3)
Class A/B/C/D/E/F

EN
2201
2207
2213
{0}
Page 58/339
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Gen. overcurrent, TOC: Self acknowledgment (Level 1/Level 2/Level 3)
On / Off
Yes ................The control automatically clears the alarm if the fault condition is no
longer detected.
Woodward
Manual 37427
Configure Monitoring: Generator, Reverse/Reduced Power (Levels 1 & 2) ANSI# 32R/F

The power produced by the generator is calculated from the voltage and current values measured in accordance
with how parameters "Generator voltage measuring" (parameter 1851 on page 40) and "Generator current
measuring" (parameter 1850 on page 40) are configured. The generator power limits may be configured for
reduced power and/or reverse power depending on the threshold values entered. The note below explains how a
reduced or reverse power limit is configured. If the single-phase or three-phase measured real power is below the
configured limit of the reduced load or below the configured value of the reverse power, an alarm will be issued.
If this protective function is triggered, the display indicates "Gen. rev./red. pwr.1" or
"Gen. rev./red. pwr.2" and the logical command variable "06.12" or "06.13" will be enabled.
NOTE
Definition
Reduced power
Fault initiated if the monitored real power falls below the configured (positive) limit.
Reverse power
Fault initiated if the direction of the monitored real power reverses and the configured (negative)
limit is exceeded.
The values for reverse /reduced power monitoring can be configured as follows:
Level 1 limit = Positive and

Level 2 limit = Positive (whereas Level 1 limit > Level 2 limit > 0 %):
Both limits are configured for reduced power monitoring.
(example: rated power is 100 kW, Level 1 limit = 5 % > Level 2 limit = 3 %; tripping if real power falls
below
5 kW (Level 1 limit) or 3 kW (Level 2 limit))
Level 1 limit = Negative and

Level 2 limit = Negative (whereas Level 2 limit < Level 1 limit < 0%):
Both limits are configured for reverse power monitoring.
(example: rated power is 100 kW, Level 1 limit = -3 % > Level 2 limit = -5 %; tripping if real power
falls below
-3 kW (Level 1 limit) or -5 kW (Level 2 limit))
Level 1 limit = Positive and

Level 2 limit = Negative (whereas Level 1 limit > 0 % > Level 2 limit):
Level 1 is configured for reduced power monitoring and
Level 2 is configured for reverse power monitoring.
(example: rated power is 100 kW, Level 1 limit = 3 % > Level 2 limit = -5 %; tripping if real power
falls below
3 kW (Level 1 limit) or -5 kW (Level 2 limit))
Parameter table
thresholds.
Level
Text
Setting range
Reverse / reduced power (the hysteresis is 1 % of the rated value)
Monitoring
On / Off
Level 1
Limit
-99.9 to 99.9 %
0.02 to 99.99 s
Level 1 > 0 % Delay
Red. power Alarm class
A/B/C/D/E/F
Yes / No
Level 1 < 0 % Self acknowledgment
Rev. power Delayed by engine speed
Yes / No
Monitoring
On / Off
Level 2
Limit
-99.9 to 99.9 %
0.02 to 99.99 s
Level 2 > 0 % Delay
Red. power Alarm class
A/B/C/D/E/F
Yes / No
Level 2 < 0 % Self acknowledgment
Rev. power Delayed by engine speed
Yes / No
Default value
On
-3.0 %
5.00 s
B
No
No
On
-5.0 %
3.00 s
E
No
No
Table 3-16: Monitoring - standard values - generator reverse / reduced power
Woodward
Page 59/339
DE
EN
Manual 37427
CL2
{0}
{1o}
DE
EN
2250
2256
CL2
2254
2260
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. reverse/reduced power: Monitoring (Level 1/Level 2)
On / Off
On................. Reverse/reduced power monitoring is carried out according to the

following parameters. Both values may be configured independent
from each other (prerequisite for {1oc}, {2oc}: GCB must be
closed).
Gen. reverse/reduced power: Threshold value (Level 1/Level 2)
-99.9 to 99.9 %
This value refers to the Generator rated active power (parameter 1752 on
page 38).
DE
EN
CL2
{0}
{1o}
DE
EN
2255
2261
CL2
{0}
DE
CL2
2252
2258
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. reverse/reduced power: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator power falls below the threshold value for the delay
time configured here, an alarm will be issued. If the monitored generator power
exceeds or falls below the threshold (plus/minus the hysteresis) again before the
delay expires the time will be reset.
Gen. reverse/reduced power: Alarm class (Lim.1/Lim.2)
Class A/B/C/D/E/F

EN
2251
2257
Delay
Verzgerung
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2253
2259
Page 60/339
Gen. reverse/reduced power: Self acknowledgment (Level 1/Level 2)
Yes / No
Yes ................ The control automatically clears the alarm if the fault condition is
no longer detected.
Gen. reverse/reduced power: Engine delayed monitoring (Level 1/Level 2)
Yes / No
Yes ................ Monitoring for fault conditions is not performed until engine
Woodward
Manual 37427
Configure Monitoring: Generator, Overload IOP (Levels 1 & 2) ANSI# 32

(IOP = Isolated Operation in Parallel)
The power produced by the generator is calculated from the voltage and current values measured inaccordance
measuring" (parameter 1850 on page 40) are configured. The controller monitors if the system is in a mains
parallel or an isolated operation. When the contoller detects that the system is operating isolated from the mains,
the Generator Overload MOP (refer to page 63) monitoring is disabled. If the measured generator real power
during an isolated operation is above the configured limit an alarm will be issued.
If this protective function is triggered, the display indicates "Gen. Overload IOP 1" or
"Gen. Overload IOP 2" and the logical command variable "06.14" or "06.15" will be enabled.
Parameter table
thresholds.
Level
Text
Overload (the hysteresis is 1 % of the rated value)
Monitoring
Level 1
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
50.0 to 300.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
On / Off
50.0 to 300.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
On
110.0 %
11.00 s
B
No
On
120.0 %
0.10 s
E
No
DE
EN
Table 3-17: Monitoring - standard values - generator overload IOP
CL2
{0}
{1o}
DE
EN
2300
2306
CL2
2304
2310
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. overload IOP: Monitoring (Level 1/Level 2)
On / Off
On ................ Overload monitoring is carried out according to the following

Gen. overload IOP: Threshold value (Level 1/Level 2)
50.0 to 300.00 %
page 38).
DE
EN
CL2
{0}
{1o}
DE
EN
2305
2311
CL2
2301
2307
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. overload IOP: Delayed (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator load exceeds the threshold value for the delay time
configured here, an alarm will be issued. If the monitored generator load falls
reset.
Gen. overload IOP: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

should be taken when the limit is surpassed.-
Page 61/339
DE
EN
Manual 37427
CL2
2302
2308
{0}
Page 62/339
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Gen. overload IOP: Self acknowledgment (Level 1/Level 2)
Yes / No
longer detected.
Woodward
Manual 37427
Configure Monitoring: Generator, Overload MOP (Levels 1 & 2) ANSI# 32

(MOP = Mains Parallel Operation)
The power produced by the generator is calculated from the voltage and current values measured inaccordance
measuring" (parameter 1850 on page 40) are configured. The controller monitors if the system is in a mains
parallel or an isolated operation. When the contoller detects that the system is operating parallel with the mains,
the Generator Overload IOP (refer to page 61) monitoring is disabled. If the measured generator real power
during a mains parallel operation is above the configured limit an alarm will be issued.
If this protective function is triggered, the display indicates "Gen. Overload MOP 1" or
"Gen. Overload MOP 2" and the logical command variable "06.23" or "06.24" will be enabled.
Parameter table
thresholds.
Level
Text
Overload (the hysteresis is 1 % of the rated value)
Monitoring
Level 1
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
50.0 to 300.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
On / Off
50.0 to 300.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
On
110.0 %
11.00 s
B
No
On
120.0 %
0.10 s
E
No
DE
EN
Table 3-18: Monitoring - standard values - generator overload MOP
CL2
{0}
{1o}
DE
EN
2350
2356
CL2
2354
2360
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. overload MOP: Monitoring (Level 1/Level 2)
On / Off
On ................ Overload monitoring is carried out according to the following

Gen. overload MOP: Threshold value (Level 1/Level 2)
50.0 to 300.00 %
page 38).
DE
EN
CL2
{0}
{1o}
DE
EN
2355
2361
CL2
2351
2357
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. overload MOP: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator load exceeds the threshold value for the delay time
configured here, an alarm will be issued. If the monitored generator load falls
reset.
Gen. overload MOP: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

Page 63/339
DE
EN
Manual 37427
CL2
2352
2358
{0}
Page 64/339
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Gen. overload MOP: Self acknowledgment (Level 1/Level 2)
Yes / No
longer detected.
Woodward
Manual 37427
Configure Monitoring: Generator, Unbalanced Load (Levels 1 & 2) ANSI# 46

Unbalanced load is monitored according to how the parameters "Generator voltage measuring" (parameter 1851
on page 40) and "Generator current measuring" (parameter 1850 on page 40) are configured. The unbalanced
load alarm monitors the individual phase currents of the generator. The percentage threshold value is the
permissible variation of one pahse from the average measured current of all three phases.
If this protective function is triggered, the display indicates "Unbalanced load 1" or
"Unbalanced load 2" and the logical command variable "06.16" or "06.17" will be enabled.
Parameter table
thresholds.
Level
Text
Unbalanced load (the hysteresis is 1 % of the rated value)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
0.0 to 100.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
0.0 to 100.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
10.0 %
10.00 s
B
No
No
On
15.0 %
1.00 s
E
No
No
Table 3-19: Monitoring - standard values - generator unbalanced load
NOTE
This monitoring function is only enabled when Generator voltage measuring (parameter 1851) is
configured to "3Ph 4W" or "3Ph 3W" and Generator current measuring (parameter 1850) is configured
to "L1 L2 L3".
Woodward
Page 65/339
Manual 37427
Formulas for calculation

Phase L1
3 I N PA + I L 2 + I L3
I L1
Exceeding
2
I L 2 + I L3 3 I N PA
Falling below
I L1
2
I L2
I L2
Phase L2
3 I N PA + I L1 + I L3
2
I L1 + I L3 3 I N PA
I L3
I L3
Phase L3
3 I N PA + I L1 + I L 2
2
I L1 + I L 2 3 I N PA
Example 1 - exceeding a limit value

Current in phase L1 = current in phase L3
Current in phase L2 has been exceeded
PA ...... tripping value percentage
IN ....... rated current
(example 10 %)
(example 300 A)
Tripping value for phase L2:
I L2
3 I N PA + I L1 + I L3 3 300A 10% + 300A + 300A
=
=
2
2
3 300A 10
+ 300A + 300A
100
= 345A
2
Example 2 falling below a limit value

Current in phase L2 = current in phase L3
Current in phase L1 has been undershot
PA ...... tripping value percentage
IN ....... rated current
(example 10 %)
(example 300 A)
Tripping value for phase L1:
I L1
I + I L3 3 I N PA 300A + 300A 3 300A 10%

L2
=
=
2
2
Page 66/339
300A + 300A
2
3 300A 10
100
= 255A
Woodward
Manual 37427
DE
EN
Parameters
CL2
{0}
{1o}
DE
EN
2400
2406
CL2
2404
2410
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. unbalanced load: Monitoring (Level 1/Level 2)
On / Off
On ................ Unbalanced load monitoring is carried out according to the

values may be configured independent from each other (condition:
Level 1 < Level 2).
Off ................ No monitoring is carried out for either Level 1 limit or Level 2
limit.
Gen. unbalanced load: Threshold value (Level 1/Level 2)
0.0 to 100.0 %
This value refers to the Generator rated current (parameter 1754 on

page 38).
DE
EN
The percentage value that is to be monitored is defined here. If the current in one
phase differs from the average value of all three phases by more than this value for
at least the delay time without interruption, the action specified by the alarm class
is initiated.
CL2
{0}
{1o}
DE
EN
2405
2411
CL2
{0}
DE
CL2
2402
2408
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. unbalanced load: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored current exceeds the average value of all three phases by more
than the threshold value for the delay time configured here, an alarm will be
issued. If the monitored current falls below the threshold (minus the hysteresis)
before the delay expires the time will be reset.
Gen. unbalanced load: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

EN
2401
2407
Delay
Verzgerung
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2403
2409
Woodward
Gen. unbalanced load: Self acknowledgment (Level 1/Level 2)
Yes / No
Yes ............... The control automatically clears the alarm if the fault condition is
no longer detected.
No................. The control does not automatically reset the alarm when the fault
Gen. unbalanced load: Engine delayed monitoring (Level 1/Level 2)
Yes / No
Yes ............... Monitoring for fault conditions is not performed until engine
No................. Monitoring for this fault condition is continuously enabled
Page 67/339
Manual 37427
Configure Monitoring: Generator, Voltage Asymmetry

The voltage asymetry alarm monitors the individual three-phase voltages of the generator. Voltage asymmetry
monitoring is always performed phase-phase (delta). The percentage threshold value is the permissible variation
from the average measured voltage of all three phases. If a measured voltage exceeds a configured permissible
asymmetrical voltage deviation from the average voltage value, an alarm is issued.
If this protective function is triggered, the display indicates "Gen. volt. asymmetry" and the logical
command variable "06.18" will be enabled.
Parameter table
Level
Text
Setting range
Generator voltage asymmetry (the hysteresis is 0.7 % of the rated value).
Monitoring
On / Off
Limit
0.5 to 15.0 %
Delay
0.02 to 99.99 s
Alarm class
A/B/C/D/E/F
Self acknowledgment
Yes / No
Yes / No
Default value
On
10.0 %
5.00 s
F
No
Yes
Table 3-20: Monitoring - standard values - generator voltage asymmetry
NOTE
DE
EN
This monitoring function is only enabled if Generator voltage measuring (parameter 1851) is configured
to "3Ph 4W" or "3Ph 3W".
CL2
{0}
{1o}
DE
EN
3900
CL2
3903
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. voltage asymmetry: Monitoring
On / Off
On ................ Voltage asymmetry monitoring is carried out according to the

following parameters.
Off ............... No monitoring is carried out.
Gen. voltage asymmetry: Threshold value
0.5 to 15.0 %
This value refers to Generator rated voltage (parameter 1766 on page 38).
DE
EN
The percentage value that is to be monitored is defined here. If the voltage in one
phase differs from the average value of all three phases by more than this value for
at least the delay time without interruption, the action specified by the alarm class
is initiated.
CL2
{0}
{1o}
DE
EN
3904
CL2
3901
{0}
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. voltage asymmetry: Delay
0.02 to 99.99 s
If the monitored generator voltage asymmetry exceeds the threshold value for the
voltage asymmetry falls below the threshold (minus the hysteresis) before the
Gen. voltage asymmetry: Alarm class
Class A/B/C/D/E/F

Page 68/339
Woodward
DE
EN
Manual 37427
CL2
3902
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3905
Woodward
Gen. voltage asymmetry: Self acknowledgment
Yes / No
no longer detected.
Gen. voltage asymmetry: Engine delayed monitoring
Yes / No
Page 69/339
Manual 37427
Configure Monitoring: Generator, Ground Fault (Levels 1 & 2)

Mains Current Input is Configured for Mains Current (Calculated Ground Fault)
(Refer to parameter 1854 on page 41)
The current produced by the generator is monitored depending on how parameter "Generator current measuring"
(parameter 1850 on page 40) is configured. The measured three conductor currents IGen-L1, IGen-L2 and IGen-L3 are
vectorially totaled (IS = IGen-L1 + IGen-L2 + IGen-L3) and compared with the configured fault limit (the calculated
actual value is indicated in the display). If the measured value exceeds the fault threshold limit, a ground fault is
present, and an alarm is issued.
If this protective function is triggered, the display indicates "Ground fault 1" or "Ground fault 2" and
the logical command variable "06.19" or "06.20" will be enabled.
NOTE
The ground fault protection zone is determined by the location where the generator current transformer
are physically installed.
IGen L1 IGen L2 IGen L3

L1
L2
L3
N
G
3~
IN=0
R
Figure 3-4: Monitoring - calculated generator ground fault
Test: Short-circuit one of the three generator current transformers while the generator is at full load. The
measured current should read 100% of rated on the two phases that do not have their current transformers shortcircuited.
The ground current calculation does not take current on the neutral conductor into consideration. In order for the
controller to be able to perform calculated ground fault current protection accurately, the neutral conductor must
not conduct current.
The fault threshold value is configured as a percentage. This percentage threshold refers to the generator rated
current (parameter 1754). Due to unavoidable load asymmetries, the minimum value for this parameter should be
10% or greater.
Page 70/339
Woodward
Manual 37427
Calculation
a)
IL1
b)
IL1
Y
IL3'
IL3Y
IL1'
IS
IL3X
IL2Y
IL3
IL2
IL2X
a) No ground fault
IL2'
IL3Y
c)
IL3'
IL1'
IL2'
IL3X
IL2Y
IL3
IL3'
IL1'
IS
IL2
IL2
IL2X
b) Ground fault (with vectorial calculation)
c) Ground fault (IS = ground fault current)
Figure 3-5: Monitoring - calculated generator ground current - vector diagram
The ground current IS is calculated geometrically/vectorially. The pointers for phase currents IL1 and IL2 are
parallel shifted and lined up as shown in Figure 3-5 a). The pointer between the neutral point and the point of the
shifted pointer IL2' results is the sum current IS as shown in Figure 3-5 b). In order to be able to add the pointers
vectorially, these must be divided into their X- and Y-coordinates (IL2X, IL2Y, IL3X and IL3Y). The ground fault
current may be calculated using the following formula:
(IL1rated + IL2rated + IL3rated) - (IL1measured + IL2measured + IL3measured) / 1.73 = Is
(7A + 7A + 7A) (7A + 6.5A + 6A) / 1.73 = 0.866A
Results of a calculation example:
Phase current IL1 = IRated = 7 A
Phase current IL2 = 6.5 A
Phase current IL3 = 6 A
Sum current (ground fault current) IS = 0.866A.
Mains Current Input is Configured for Ground Current (Measured Ground Fault)
(Refer to parameter 1854 on page 41)
Ground fault current is actively measured when the mains current input is configured to monitor for ground
current. The ground fault threshold is configured as a percentage of the value entered for parameter "Ground
current transformer" (parameters 1810 or Fehler! Verweisquelle konnte nicht gefunden werden. on page 46).
NOTE
The ground fault protection zone is determined by the physical installation location of the generator
current transformer.
Parameter table
thresholds.
Level
Text
Setting range
Generator ground fault (the hysteresis is 0.7 % of the rated value)
Level 1
Monitoring
On / Off
Limit
0 to 300 %
Delay
0.02 to 99.99 s
Alarm class
A/B/C/D/E/F
Self acknowledgment
Yes / No
Yes / No
Level 2
Monitoring
On / Off
Limit
0 to 300 %
Delay
0.02 to 99.99 s
Alarm class
A/B/C/D/E/F
Self acknowledgment
Yes / No
Yes / No
Default value
Off
10 %
0.20 s
B
No
No
Off
30 %
0.10 s
F
No
No
Table 3-21: Monitoring - standard values - generator ground fault
Woodward
Page 71/339
Manual 37427
DE
EN
Parameter
CL2
{0}
{1o}
DE
EN
3250
3256
CL2
3254
3260
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Gen. ground fault: Monitoring (Level 1/Level 2)
On / Off
On................. Ground current monitoring is carried out according to the following

< Level 2).
Gen. ground fault: Threshold value (Level 1/Level 2)
0 to 300 %
This value refers to the Generator rated current of the generator

(parameter 1754 on page 38), if the ground current is calculated from the
generator current values. It refers to the parameter "Ground current
transformer" (parameters 1810 or Fehler! Verweisquelle konnte nicht
gefunden werden. on page 46), if the ground current is measured directly.
NOTE
DE
EN
The ground fault threshold shall not exceed the mains/ground current measuring range (approx. 1.5
Irated; refer to the Technical Data section of the Installation Manual 37426).
CL2
{0}
{1o}
DE
EN
3255
3261
CL2
{0}
DE
CL2
3252
3258
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. ground fault: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored ground fault exceeds the threshold value for the delay time
configured here, an alarm will be issued. If the monitored ground fault falls below
the threshold (minus the hysteresis) before the delay expires the time will be reset.
Gen. ground fault: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

EN
3251
3257
Delay
Verzgerung
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3253
3259
Page 72/339
Gen. ground fault: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Gen. ground fault: Engine delayed monitoring (Level 1/Level 2)
Yes / No
Woodward
Manual 37427
Configure Monitoring: Generator, Phase Rotation
CAUTION
Ensure that the control unit is properly connected to phase voltages on both sides of the circuit
breaker(s) during installation. Failure to do so may result in damage to the control unit and/or
generation equipment due to the breaker closing asynchronously or with mismatched phase rotations.
Also ensure that phase rotation monitoring is enabled at all connected components (engine, generator,
breakers, cable, busbars, etc.).
This function will block a connection of systems with mismatched phases only under the following
conditions:
The voltages being measured are wired correctly with respect to the phase rotation at the
measuring points (i.e. the potential transformers in on both sides of the circuit breaker)
The voltages being measured are wired so that angular phase shifts or any interruptions from the
measuring point to the control unit do not exist
The voltages being measured are wired to the correct terminals of the control unit (i.e. L1 phase of
the generator is connected with the terminal of the control unit which is intended for the generator
L1 phase)
The configured alarm class is of class C, D, E, or F (shutdown alarm).
Correct phase rotation of the phase voltages ensures that damage will not occur during a breaker closure to either
the mains or the generator. The voltage phase rotation alarm checks the phase rotation of the measured voltages
and the configured phase rotation to ensure they are identical. The directions of rotation are differentiated as
"clockwise" and "counter clockwise". With a clockwise field the direction of rotation is "L1-L2-L3"; with a
counter clockwise field the direction of rotation is "L1-L3-L2". If the control is configured for a clockwise
rotation and the measured voltages are monitored as counterclockwise, the alarm will be initiated. The direction
of configured rotation being monitored by the control unit is displayed on the screen.
If this protective function is triggered, the display indicates "Gen.ph.rot. mismatch" and the logical
Parameter table
Level
Text
Setting range
Generator voltage phase direction fault (the hysteresis is 0.7 % of the rated value)
Monitoring
On / Off
Generator phase rotation
CW / CCW
Alarm class
A/B/C/D/E/F
Self acknowledgment
Yes / No
Yes / No
Default value
On
CW
F
No
Yes
Table 3-22: Monitoring - standard values - generator voltage phase rotation
NOTE
This monitoring function is only enabled if Generator voltage measuring (parameter 1851) is configured
to "3Ph 4W" or "3Ph 3W" and the measured voltage exceeds 50 % of the rated voltage (parameter 1766)
or if Generator voltage measuring (parameter 1851) is configured to "1Ph 2W" (in this case, the phase
rotation is not evaluated, but defined by the 1Ph2W phase rotation (parameter 1859)).
Woodward
Page 73/339
DE
EN
Manual 37427
CL2
DE
EN
3950
CL2
{1o}
{0}
{1o}
DE
CL2
3951
{1oc}
{2oc}
Generator phase rotation

Generatordrehfeld
EN
3954
{0}
Monitoring
berwachung
{0}
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen.voltage phase rotation: Monitoring
On / Off
On................. Phase rotation monitoring is carried out according to the following

parameters.
Off ................ No monitoring is carried out.
Gen.voltage phase rotation: Direction
CW / CCW
CW ............... The three-phase measured generator voltage is rotating CW (clockwise; that means the voltage rotates in L1-L2-L3 direction; standard
setting).
CCW ............ The three-phase measured generator voltage is rotating CCW
(counter clock-wise; that means the voltage rotates in L1-L3-L2
direction).
Gen.voltage phase rotation: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
3952
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3953
Page 74/339
Gen.voltage phase rotation: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Gen.voltage phase rotation: Engine delayed monitoring
Yes / No
Woodward
Manual 37427
Configure Monitoring: Generator, Inverse Time-Overcurrent Monitoring ANSI# IEC 255

The current produced by the generator is monitored depending on how parameter "Generator current measuring"
(parameter 1850 on page 40) is configured. If an overcurrent condition is detected, the fault recognition time is
determined by the configured tripping characteristic curve and the measured current. The tripping time is faster as
the measured current increases in magnitude according to a defined curve. According to IEC 255 three different
characteristics are available.
If this protective function is triggered, the display indicates "Inv. time overcurr." and the logical
"Normal inverse" characteristic:
t=
"Highly inverse" characteristic:
t=
"Extremely inverse" characteristic:
t=
Variable meanings:
t:
tp
I
Ip
0.14
( I / I P ) 0.02 1
* t p [s]
13.5
* t p [s]
(I / I P ) 1
80
(I / I P )2 1
* t p [s]
tripping time
setting value time
measured fault current
setting value current
Please take into account during configuration:

for Istart:
for Ip
Istart > In and Istart > Ip

the smaller Ip is, the steeper is the slope of the tripping curve
NOTE
The maximum tripping time is 327 s. If a tripping time greater than 327 s is configured, an overcurrent
fault condition will not be recognized.
Normal Inverse
Ip = 1 x In; I start = 1.1 x In
t[s]
1000
100
10
tp = 1.6 s
tp = 1.0 s
tp = 0.5 s
tp = 0.2 s
tp = 0.1 s
tp = 0.05 s
0.1
I start/Ip
0.01
1
10
I/Ip
100
Figure 3-6: Monitoring - generator inverse time-overcurrent - "Normal inverse" characteristic
Woodward
Page 75/339
Manual 37427
Highly inverse
Ip = In; I-Start = 1.1 x In
t[s]
1000
100
10
tp = 1.6 s
tp = 1.0 s
tp = 0.5 s
tp = 0.2 s
0.1
tp = 0.1 s
tp = 0.05 s
I-Start/Ip
0.01
1
10
I/Ip
100
Figure 3-7: Monitoring - generator inverse time-overcurrent - "Highly inverse" characteristic
Extremely inverse
Ip = In; I-Start = 1.1 x In
t[s]
1000
100
10
tp = 1.6 s
tp = 1.0 s
0.1
tp = 0.5 s
tp = 0.2 s
I-Start/Ip
tp = 0.05 s
tp = 0.1 s
0.01
1
10
I/Ip
100
Figure 3-8: Monitoring - generator inverse time-overcurrent - "Extremely inverse" characteristic
Page 76/339
Woodward
Manual 37427
Parameter table
Level
Text
Setting range
Inverse time-overcurrent (the hysteresis is 1 % of the rated value)
Monitoring
On / Off
Inverse time characteristic
Normal / High / Extreme
Inverse time overcurrent Tp
0.01 to 1.99 s
Inverse time overcurrent Ip
10.0 to 300.0 %
Inv. time overcurrent I start
100.0 to 300.0 %
Alarm class
A/B/C/D/E/F
Self acknowledgment
Yes / No
Yes / No
Default value
On
Normal
0.06 s
100.0 %
115.0 %
F
No
No
DE
EN
Table 3-23: Monitoring - standard values - generator inverse time-overcurrent
CL2
DE
EN
4030
CL2
4034
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Inverse time characteristic

berstrom Charakteristik
{0}
{1o}
{1oc}
{2oc}
Gen. overcurrent, inverse: Monitoring
On / Off
On ................ Overcurrent monitoring is carried out according to the following

parameters.
Gen. overcurrent, inverse: Tripping characteristic
Normal / High / Extreme
Selection of the used overcurrent characteristic.

Normal......... The "normal inverse" tripping curve will be used
High ............. The "highly inverse" tripping curve will be used
Extreme ....... The "extremely inverse" tripping curve will be used.
DE
EN
DE
EN
Inverse time overcurrent Tp=

berstrom (AMZ) Tp=
CL2 {0} {1o} {1oc} {2oc}
4035
CL2
DE
EN
4036
CL2
4037
Inverse time overcurr. Ip=

berstrom (AMZ) Ip=
{0}
{1o}
{1oc}
{2oc}
Inv time overcurr. I-start=

berstrom (AMZ) I-Start=
{0}
Woodward
{1o}
{1oc}
{2oc}
Gen. overcurrent, inverse: Time constant Tp
0.01 to 1.99 s
Time constant Tp used to calculate the characteristics.

Gen. overcurrent, inverse: Current constant Ip
10.0 to 300.0 %
Current constant Ip used to calculate the characteristics.

Gen. overcurrent, inverse: I start
100.0 to 300.0 %
Lower tripping value for inverse time-overcurrent protection. If the monitored

current is less than Istart, the inverse time-overcurrent protection does not trip. If Istart
is less than Ip, Ip is used as the lower tripping value.
Page 77/339
DE
EN
Manual 37427
CL2
4031
{0}
{1o}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. overcurrent, inverse: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
4032
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
4033
Page 78/339
Gen. overcurrent, inverse: Self acknowledgment
Yes / No
no longer detected.
Gen. overcurrent, inverse: Engine delayed monitoring
Yes / No
Woodward
Manual 37427
Configure Monitoring: Generator, Lagging Power Factor Monitoring (Levels 1 & 2)

The power factor is monitored for becoming more lagging (i.e. inductive) than an adjustable limit. This limit may
be a lagging or leading power factor limit. There are two lagging power factor alarm levels available in the
control. This monitoring function may be used for monitoring an overexcitation with a warning and a shutdown
alarm level. Both alarms are definite time alarms. Refer to the Application Manual 37429 for a detailed
description of this monitoring function.
Figure 3-9 shows an example of a leading and a lagging power factor limit and the power factor range, for which
the lagging power factor monitoring issues an alarm.
If this protective function is triggered, the display indicates "Gen. PF lagging 1" or
"Gen. PF lagging 2" and the logical command variable "06.25" or "06.26" will be enabled.
Power Factor
Leading (capacitive)
Lagging (inductive)
More lagging than a leading PF limit of -0.4
-0.4
- 0.5
- 0.75
More lagging than a lagging PF limit of +0.85
1.00
Import Inductive Power
+0.85
+0.75
+0.5
Export inductive Power

Figure 3-9: Monitoring - generator lagging power factor
Parameter table
thresholds.
Level
Text
Generator lagging power factor
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
-0.001 to +0.001
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
-0.001 to +0.001
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
+0.900
30.00 s
B
No
Yes
On
+0.700
1.00 s
E
No
Yes
Table 3-24: Monitoring - standard values - generator lagging power factor
Woodward
Page 79/339
DE
EN
Manual 37427
CL2
{0}
{1o}
DE
EN
2325
2331
CL2
{0}
{1o}
DE
EN
2329
2335
CL2
{0}
{1o}
DE
EN
2330
2336
CL2
{0}
DE
CL2
2327
2333
{1o}
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Gen. lagging power factor: Monitoring (Level 1/Level 2)
On / Off
On................. Generator lagging power factor monitoring is carried out according

to the following parameters. Monitoring is performed at two levels.
Both values may be configured independent from each other.
Gen. lagging power factor: Threshold value (Level 1/Level 2)
-0.001 to +0.001
The values that are to be monitored for each threshold limit are defined here. If the
power factor becomes more lagging (i.e. inductive, refer to Figure 3-9) than a
lagging PF value (positive) or a leading PF value (negative) for at least the delay
time (parameters 2330 or 2336) without interruption, the action specified by the
alarm class is initiated.
Gen. lagging power factor: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator power factor is more lagging than the configured limit
for the delay time configured here, an alarm will be issued. If the monitored
generator power factor returns within the limit before the delay expires the time
will be reset.
Gen. lagging power factor: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

EN
2326
2332
Monitoring
berwachung
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2328
2334
Page 80/339
Gen. lagging power factor: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Gen. lagging power factor: Engine delayed monitoring (Level 1/Level 2)
Yes / No
Woodward
Manual 37427
Configure Monitoring: Generator, Leading Power Factor Monitoring (Levels 1 & 2)

The power factor is monitored for becoming more leading (i.e. capacitive) than an adjustable limit. This limit
may be a leading or lagging power factor limit. There are two leading power factor alarm levels available in the
control. This monitoring function may be used for monitoring an underexcitation with a warning and a shutdown
alarm level. Both alarms are definite time alarms. Refer to the Application Manual 37429 for a detailed
description of this monitoring function.
Figure 3-10 shows an example of a leading and a lagging power factor limit and the power factor range, for
which the leading power factor monitoring issues an alarm.
If this protective function is triggered, the display indicates "Gen. PF leading 1" or
"Gen. PF leading 2" and the logical command variable "06.27" or "06.28" will be enabled.
Power Factor
Leading (capacitive)
Lagging (inductive)
More leading than a leading PF limit of -0.85
- 0.5
- 0.75
-0.85
More leading than a lagging PF limit of +0.4
1.00
Import Inductive Power
+0.75
+0.5
+0.4
Export inductive Power

Figure 3-10: Monitoring - generator leading power factor
Parameter table
thresholds.
Level
Text
Generator leading power factor
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
-0.001 to +0.001
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
-0.001 to +0.001
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
-0.900
30.00 s
B
No
Yes
On
-0.700
1.00 s
E
No
Yes
Table 3-25: Monitoring - standard values - generator leading power factor
Woodward
Page 81/339
DE
EN
Manual 37427
CL2
{0}
{1o}
DE
EN
2375
2381
CL2
{0}
{1o}
DE
EN
2379
2385
CL2
{0}
{1o}
DE
EN
2380
2386
CL2
{0}
{1o}
2377
2383
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Self acknowledge
Selbstquittierend
DE
CL2
{1oc}
Gen. leading power factor: Monitoring (Level 1/Level 2)
On / Off
On ................ Generator leading power factor monitoring is carried out according

to the following parameters. Monitoring is performed at two levels.
Both values may be configured independent from each other.
Off................ Monitoring is disabled for Level 1 limit and/or Level 2 limit.
Gen. leading power factor: Threshold value (Level 1/Level 2)
-0.001 to +0.001
The values that are to be monitored for each threshold limit are defined here. If
the power factor becomes more leading (i.e. capacitive, refer to Figure 3-10) than
a leading PF value (negative) or a lagging PF value (positive) for at least the
delay time (parameters 2380 or 2386) without interruption, the action specified
by the alarm class is initiated.
Gen. leading power factor: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored generator power factor is more leading than the configured limit
for the delay time configured here, an alarm will be issued. If the monitored
generator power factor returns within the limit before the delay expires the time
will be reset.
Gen. leading power factor: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

EN
2376
2382
Monitoring
berwachung
{0}
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2378
2384
Page 82/339
Gen. leading power factor: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Gen. leading power factor: Delayed engine speed (Level 1/Level 2)
Yes / No
Woodward
Manual 37427
Configure Monitoring: Mains

Parameter Table
Level
Text
Configure mains monitoring
Mains voltage monitoring
Mains settling time
Setting range
Default value

0 to 9999 s
Phase - phase
20 s
Table 3-26: Monitoring - standard values - configure mains monitoring
DE
EN
Mains voltage monitoring

Netz Spannungsberwachung
CL2 {0} {1o} {1oc} {2oc}
1771
Mains protection: Type of monitoring
The unit can either monitor the wye voltages (phase-neutral) or the delta voltages
(phase-phase). The monitoring of the wye voltage is above all necessary to avoid
earth-faults in a compensated or isolated network resulting in the tripping of the
voltage protection.
!
WARNING:
This parameter influences the protective functions.
DE
EN
Phase - phase The phase-phase voltage will be measured and all subsequent
parameters concerning voltage monitoring "mains" are referred to
this value (VL-L).
Phase - neutral The phase-neutral voltage will be measured and all subsequent
parameters concerning voltage monitoring "mains" are referred to
this value (VL-N).
CL2
2801
{0}
Mains settling time

Netzberuhigungszeit
{1o}
{1oc}
{2oc}
Breaker: Mains failure: Mains settling time
0 to 9999 s
To end the emergency operation, the monitored mains must be within the
configured operating parameters without interruption for the minimum period of
time set with this parameter without interruption. This parameter permits delaying
the switching of the load from the generator to the mains. The display indicates
"Mains settling" during this time.
Configure Monitoring: Mains, Operating Voltage / Frequency

Parameter Table
Level
Text
Configure mains operating voltage / frequency
Upper voltage limit
Hysteresis upper voltage limit
Lower voltage limit
Hysteresis lower voltage limit
Hysteresis upper frequency limit
Hysteresis lower frequency limit
Setting range
Default value
100 to 150 %
0 to 50 %
50 to 100 %
0 to 50 %
100.0 to 150.0 %
0.0 to 50.0 %
50.0 to 100.0 %
0.0 to 50.0 %
110 %
2%
90 %
2%
110 %
0.5 %
90 %
0.5 %
DE
EN
Table 3-27: Monitoring - standard values - configure mains operating voltage / frequency
CL2
5810
Upper voltage limit

Obere Spannungsabw.
{0}
Woodward
{1o}
{1oc}
{2oc}
Operating voltage window, mains, maximum limit
100 to 150 %
The maximum permissible positive deviation of the mains voltage from the mains
rated voltage (parameter 1768 on page 38) is configured here. This value may be
used as a voltage limit switch. The conditional state of this switch may be used as a
command variable for the LogicsManager (02.09).
Page 83/339
Manual 37427
DE
EN
DE
EN
Hysteresis upper voltage limit

Hyst. obere Spannungsabw.
CL2 {0} {1o} {1oc} {2oc}
5814
CL2
5811
Lower voltage limit

Untere Spannungsabw.
{0}
{1o}
{1oc}
{2oc}
DE
EN
DE
EN
Hysteresis lower voltage limit

Hyst. untere Spannungsabw.
CL2 {0} {1o} {1oc} {2oc}
5815
CL2
DE
EN
5812
CL2
DE
EN
5813
CL2
5817
{1oc}
{2oc}
Hyst. upper frequency limit

Hyst. obere Frequenzabw.
{0}
{1o}
DE
CL2
{1o}
EN
5816
{0}

Obere Frequenzabw.
{0}
{1oc}
{2oc}

Untere Frequenzabw.
{1o}
{1oc}
{2oc}
Hyst. lower frequency limit

Hyst. untere Frequenzabw.
{0}
{1o}
{1oc}
{2oc}
Operating voltage window, mains, maximum limit hysteresis
0 to 50 %
If the mains voltage has exceeded the limit configured in parameter 5810, the
voltage must fall below the limit and the value configured here, to be considered as
being within the operating limits again.
Operating voltage window, mains, minimum limit
50 to 100 %
The maximum permissible negative deviation of the mains voltage from the mains
rated voltage (parameter 1768 on page 38) is configured here. This value may be
used as a voltage limit switch. The conditional state of this switch may be used as a
command variable for the LogicsManager (02.09).
Operating voltage window, mains, minimum limit hysteresis
0 to 50 %
If the mains voltage has fallen below the limit configured in parameter 5811, the
voltage must exceed the limit and the value configured here, to be considered as
Operating frequency window, mains, maximum limit
100.0 to 150.0 %
The maximum permissible positive deviation of the mains frequency from the rated
system frequency (parameter 1750 on page 37) is configured here. This value may
be used as a frequency limit switch. The conditional state of this switch may be
Operating frequency window, mains, maximum limit hysteresis
0.0 to 50.0 %
If the mains frequency has exceeded the limit configured in parameter 5812, the
frequency must fall below the limit and the value configured here, to be considered
as being within the operating limits again.
Operating frequency window, mains, minimum limit
50.0 to 100.0 %
The maximum permissible negative deviation of the mains frequency from the
Operating frequency window, mains, minimum limit hysteresis
0.0 to 50.0 %
If the mains frequency has fallen below the limit configured in parameter 5813, the
frequency must exceed the limit and the value configured here, to be considered as
Example:
If the mains rated voltage is 400 V, the upper voltage limit is 110 % (of the mains rated voltage, i.e. 440 V), and
the hysteresis for the upper voltage limit is 5 % (of the mains rated voltage, i.e. 20 V), the mains voltage will be
considered as being out of the operating limits as soon as it exceeds 440 V and will be considered as being within
the operating limits again as soon as it falls below 420 V (440 V 20 V).
If the rated system frequency is 50 Hz, the lower frequency limit is 90 % (of the rated system frequency, i.e.
45 Hz), and the hysteresis for the lower frequency limit is 5 % (of the rated system frequency, i.e. 2.5 Hz), the
mains frequency will be considered as being out of the operating limits as soon as it falls below 45 Hz and will be
considered as being within the operating limits again as soon as it exceeds 47.5 Hz (45 Hz + 2.5 Hz).
NOTE
The mains operating voltage/frequency parameters are used to trigger mains failure conditions and
activate an emergency run. The mains values must be within this ranges to synchronize the mains
circuit breaker. It is recommended to configure the operating limits within the monitoring limits.
Page 84/339
Woodward
Manual 37427
Configure Monitoring: Mains, Decoupling

The mains decoupling function is intended for use in a mains parallel operation and monitors a series of
subordinate mains protection thresholds. If a threshold is exceeded, the easYgen initiates a breaker opening and
separates the generator(s) from the mains at the defined breaker.
The following thresholds are monitored:
Overfrequency level 2 (refer to page 87 for detailed information)
Underfrequency level 2 (refer to page 89 for detailed information)
Overvoltage level 2 (refer to page 99 for detailed information)
Undervoltage level 2 (refer to page 93 for detailed information)
Mains phase shift (refer to page 95 for detailed information)
If one of these protective functions is triggered, the display indicates "Mains decoupling" (the logical
command variable "07.25" will be enabled) and the active level 2 alarm.
Parameter table
Level
Text
Mains decoupling
Mains decoupling
Mains decoupling feedback delay
Alarm class
Self acknowledgment
Setting range
Default value
GCB / GCB->MCB / MCB /

MCB->GCB / Off
0.10 to 5.00 s
A/B/C/D/E/F
Yes / No
GCB
0.4 s
B
No
DE
EN
Table 3-28: Monitoring - standard values - mains decoupling
CL2
3110
{0}
Mains decoupling
Netzentkopplung
{1o}
{1oc}
{2oc}
DE
EN
Mns. decoupling feedback delay

Netzentkopplg Rckmeldungszeit
{1o}
{1oc} {2oc}
CL2 {0}
3113
Woodward
Mains decoupling: Monitoring
GCB / GCB->MCB / MCB / MCB->GCB / Off
GCB .............Mains decoupling is carried out according to the following

parameters. If one of the subordinate monitoring functions is
triggered, the GCB will be opened. If the unit is operated in parallel
with the mains and the MCB opens, the GCB will be closed again.
GCB->MCB.Mains decoupling is carried out according to the following
triggered, the GCB will be opened. If the reply "GCB open" is not
present within the delay configured in parameter 3113, the MCB
will be opened as well.
MCB .............Mains decoupling is carried out according to the following
triggered, the MCB will be opened.
MCB->GCB.Mains decoupling is carried out according to the following
triggered, the MCB will be opened. If the reply "MCB open" is not
present within the delay configured in parameter 3113, the GCB
will be opened as well.
Off ................Mains decoupling monitoring is disabled.
Mains decoupling: Feedback delay
0.10 to 5.00 s
If the open signal from the respective circuit breaker cannot be detected within
the time configured here, the mains decoupling function performs the action as
configured in parameter 3110.
Page 85/339
DE
EN
Manual 37427
CL2
3111
{0}
{1o}

Alarm class
Alarmklasse
{1oc}
{2oc}
Mains decoupling: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
3112
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Mains decoupling: Self acknowledgment
Yes / No
longer detected.
NOTE
The mains decoupling function is optimized on the both relay outputs "GCB open" and "MCB open". In
case of using a free relay output in conjunction with the command variable 07.25 an additional delay
time of up to 20ms is to consider.
Page 86/339
Woodward
Manual 37427
Configure Monitoring: Mains, Overfrequency (Levels 1 & 2) ANSI# 81O

There are two overfrequency alarm levels available in the control. Both alarms are definite time alarms and are
illustrated in the figure below. The figure diagrams a frequency trend and the associated pickup times and length
of the alarms. Monitoring of the frequency is accomplished in two steps.
If this protective function is triggered, the display indicates "Mains overfreq. 1" or
"Mains overfreq. 2" and the logical command variable "07.06" or "07.07" will be enabled.
Parameter table
The parameters represented in
this table are specified in the
following, whereas the
description is identical for all
limits; the limits may only
differ in their setting ranges.
Level
Text
Overfrequency (the hysteresis is 0.05 Hz.)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
50.0 to 130.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
50.0 to 130.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
100.4 %
0.06 s
A
Yes
No
On
1020.0 %
0.06 s
B
Yes
No
DE
EN
Table 3-29: Monitoring - standard values - mains overfrequency
CL2
{0}
{1o}
DE
EN
2850
2856
CL2
2854
2860
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Mains overfrequency: Monitoring (Limit 1/Limit 2)
On / Off
On ................ Overfrequency monitoring is carried out according to the following

be configured independent from each other (prerequisite: limit 1
< Level 2 limit).
Off................ Monitoring is disabled for limit 1 and/or Level 2 limit.
Mains overfrequency: Threshold value (Limit 1/Limit 2)
50.0 to 130.0 %
This value refers to the System rated frequency (parameter 1750on

page 37).
DE
EN
CL2
{0}
{1o}
DE
EN
2855
2861
CL2
2851
2857
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Mains overfrequency: Delay (Limit 1/Limit 2)
0.02 to 99.99 s
If the monitored mains frequency value exceeds the threshold value for the delay
time configured here, an alarm will be issued. If the monitored mains frequency
falls below the threshold (minus the hysteresis) before the delay expires the time
will be reset.
Mains overfrequency: Alarm class (Limit 1/Limit 2)
Class A/B/C/D/E/F

Page 87/339
DE
EN
Manual 37427
CL2
2852
2858
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2853
2859
Mains overfrequency: Self acknowledgment (Limit 1/Limit 2)
Yes / No
no longer detected.
Mains overfrequency: Delayed engine speed (Level 1/Level 2)
Yes / No
NOTE
The mains overfrequency Level 2 limit configuration parameters are located below the mains
decoupling function menu on the display.
Page 88/339
Woodward
Manual 37427
Configure Monitoring: Mains, Underfrequency (Levels 1 & 2) ANSI# 81U

There are two underfrequency alarm levels available in the control. Both alarms are definite time alarms and are
illustrated in the figure below. The figure diagrams a frequency trend and the associated pickup times and length
of the alarms. Monitoring of the frequency is performed in two steps.
If this protective function is triggered, the display indicates "Mains underfreq. 1" or
"Mains underfreq. 2" and the logical command variable "07.08" or "07.09" will be enabled.
Parameter table
Level
Text
Underfrequency (the hysteresis is 0.05 Hz.)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment

thresholds.
Setting range
Default value
On / Off
50.0 to 130.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
50.0 to 130.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
99.6 %
1.50 s
A
Yes
No
On
98.0 %
0.06 s
B
Yes
No
DE
EN
Table 3-30: Monitoring - standard values - mains underfrequency
CL2
{0}
{1o}
DE
EN
2900
2906
CL2
2904
2910
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Mains underfrequency: Monitoring (Level 1/Level 2)
On / Off
On ................ Underfrequency monitoring is carried out according to the

values may be configured independent from each
other (prerequisite: Level 1 > Level 2).
Mains underfrequency: Threshold value (Level 1/Level 2)
50.0 to 130.0 %
This value refers to the System rated frequency (parameter 1750on

page 37).
DE
EN
CL2
{0}
{1o}
DE
EN
2905
2911
CL2
2901
2907
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Mains underfrequency: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored mains frequency value falls below the threshold value for the
delay time configured here, an alarm will be issued. If the monitored mains
frequency exceeds the threshold (plus the hysteresis) again before the delay
expires the time will be reset.
Mains underfrequency: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

Page 89/339
DE
EN
Manual 37427
CL2
2902
2908
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2903
2909
Mains underfrequency: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Mains underfrequency Engine delayed monitoring (Level 1/Level 2)
Yes / No
NOTE
The mains underfrequency Level 2 limit configuration parameters are located below the mains
decoupling function menu on the display.
Page 90/339
Woodward
Manual 37427
Configure Monitoring: Mains, Overvoltage (Levels 1 & 2) ANSI# 59

Voltage is monitored depending on parameter "Mains voltage measuring" (parameter 1853 on page 41). There
are two overvoltage alarm levels available in the control. Both alarms are definite time alarms and are illustrated
in the figure below. The figure diagrams a frequency trend and the associated pickup times and length of the
alarms. Monitoring of the voltage is done in two steps.
If this protective function is triggered, the display indicates "Mains overvoltage 1" or
"Mains overvoltage 2" and the logical command variable "07.10" or "07.11" will be enabled.
Parameter table
Level
Text
Overvoltage (the hysteresis is 0.7 % of the rated value)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment

thresholds.
Setting range
Default value
On / Off
50.0 to 125.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
50.0 to 125.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
108.0 %
1.50 s
A
Yes
No
On
110.0 %
0.06 s
B
Yes
No
DE
EN
Table 3-31: Monitoring - standard values - mains overvoltage
CL2
{0}
{1o}
DE
EN
2950
2956
CL2
{0}
{1o}
DE
CL2
{0}
{1o}
DE
EN
2955
2961
CL2
2951
2957
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Mains overvoltage: Monitoring (Level 1/Level 2)
On / Off
On ................ Overvoltage monitoring is carried out according to the following

be configured independent from each other (prerequisite: limit 1
< Level 2 limit).
Mains overvoltage: Threshold value (Level 1/Level 2)
50.0 to 125.0 %
This value refers to the Mains rated voltage (parameter 1768 on page 38).
EN
2954
2960
Monitoring
berwachung
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Mains overvoltage: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored mains voltage exceeds the threshold value for the delay time
configured here, an alarm will be issued. If the monitored mains voltage falls
be reset.
Mains overvoltage: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

Page 91/339
DE
EN
Manual 37427
CL2
2952
2958
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
--2953
2959
Mains overvoltage: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Mains overvoltage: Engine delayed monitoring (Level 1/Level 2)
Yes / No
NOTE
The mains overvoltage Level 2 limit configuration parameters are located below the mains decoupling
function menu on the display.
Page 92/339
Woodward
Manual 37427
Configure Monitoring: Mains, Undervoltage (Levels 1 & 2) ANSI# 27

Voltage is monitored depending on parameter "Mains voltage measuring" (parameter 1853 on page 41). There
are two undervoltage alarm levels available in the control. Both alarms are definite time alarms and are illustrated
in the figure below. The figure diagrams a frequency trend and the associated pickup times and length of the
alarms. Monitoring of the voltage is done in two steps.
If this protective function is triggered, the display indicates "Mains undervoltage 1" or
"Mains undervoltage 2" and the logical command variable "07.12" or "07.13" will be enabled.
Parameter table
Level
Text
Undervoltage (the hysteresis is 0.7 % of the rated value)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment

thresholds.
Setting range
Default value
On / Off
50.0 to 125.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
50.0 to 125.0 %
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
92.0 %
1.50 s
A
Yes
No
On
90.0 %
0.06 s
B
Yes
No
DE
EN
Table 3-32: Monitoring - standard values - mains undervoltage
CL2
{0}
{1o}
DE
EN
3000
3006
CL2
{0}
{1o}
DE
CL2
{0}
{1o}
DE
EN
3005
3011
CL2
3001
3007
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Mains undervoltage: Monitoring (Level 1/Level 2)
On / Off
On ................ Undervoltage monitoring is carried out according to the following

Off................ Monitoring is disabled for Level 1 limit and/or Level 2 limit.
Mains undervoltage: Threshold value (Level 1/Level 2)
50.0 to 125.0 %
This value refers to the Mains rated voltage (parameter 1768 on page 38).
EN
3004
3010
Monitoring
berwachung
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Mains undervoltage: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored mains voltage falls below the threshold value for the delay time
configured here, an alarm will be issued. If the monitored mains voltage exceeds
the threshold (plus the hysteresis) again before the delay expires the time will be
reset.
Mains undervoltage: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

Page 93/339
DE
EN
Manual 37427
CL2
3002
3008
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3003
3009
Mains undervoltage: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Mains undervoltage: Delayed engine speed (Level 1/Level 2)
Yes / No
NOTE
The mains undervoltage Level 2 limit configuration parameters are located below the mains decoupling
function menu on the display.
Page 94/339
Woodward
Manual 37427
Configure Monitoring: Mains, Phase Shift

A vector/phase shift is defined as the sudden variation of the voltage curve which may be caused by a major
generator load change. It usually occurs, if the utility opens the MCB, which causes a load change for the genset.
The easYgen measures the duration of a cycle, where a new measurement is started with each voltage passing
through zero. The measured cycle duration will be compared with an internal quartz-calibrated reference time to
determine the cycle duration difference of the voltage signal. A vector/phase shift as shown in Figure 3-11 causes
a premature or delayed zero passage. The determined cycle duration difference corresponds with the occurring
phase shift angle.
Figure 3-11: Monitoring - phase shift
The monitoring may be carried out three-phased or one/three-phased. Different limits may be configured for onephase and three-phase monitoring. The vector/phase shift monitor can also be used as an additional method to
decouple from the mains. Vector/phase shift monitoring is only enabled after the monitored voltage exceeds 50%
of the PT secondary rated voltage.
Function: "Voltage cycle duration not within the permissible range" - The voltage cycle duration exceeds the
configured limit value for the phase/vector shift. The result is, that the power circuit breaker that disconnects
from the mains, is opened, the message "Mains phase shift" is displayed, and the logical command
variable "07.14" is enabled. The prerequisite for phase/vector shift monitoring is that the generator is operating in
a mains parallel operation (the MCB and GCB are both closed).
Parameter table
Level
Text
Mains phase shift
Monitoring
Monitoring
Limit 1 phae
Limit 3 phase
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
1- and 3 phase / 3 phase
3 to 30
3 to 30
A/B/C/D/E/F
Yes / No
Yes / No
On
1- and 3 phase
20
8
B
Yes
No
Table 3-33: Monitoring - standard values - mains phase shift
Woodward
Page 95/339
DE
EN
Manual 37427
CL2
{0}
{1o}
DE
CL2
3053
Monitoring
berwachung
{1oc}
{2oc}
Monitoring
berwachung auf
EN
3050
{0}
{1o}
{1oc}
{2oc}
Mains phase shift: Monitoring
On / Off
On .................Phase shift monitoring is carried out according to the following

parameters.
Off ................Monitoring is disabled.
Mains phase shift: Monitoring
1- and 3 phase / 3 phase
1- and 3 phase During single-phase voltage phase/vector shift monitoring,

tripping occurs if the phase/vector shift exceeds the configured
threshold value (parameter 3054) in at least one of the three phases.
Note: If a phase/vector shift occurs in one or two phases, the singlephase threshold value (parameter 3054) is taken into consideration; if
a phase/vector shift occurs in all three phases, the three-phase
threshold value (parameter 3055) is taken into consideration. Single
phase monitoring is very sensitive and may lead to nuisance tripping
if the selected phase angle settings are too small.
3 phase .........During three-phase voltage phase/vector shift monitoring, tripping
occurs only if the phase/vector shift exceeds the specified threshold
value (parameter 3055) in all three phases within 2 cycles.
NOTE
DE
EN
3 phase mains phase shift monitoring is only enabled if Mains voltage measuring (parameter 1853) is
configured to "3Ph 4W" or "3Ph 3W".
CL2
{0}
DE
CL2
{0}
{1o}
DE
CL2
3051
{1oc}
{2oc}
Limit 3 phase
Grenzwert 3-phasig
EN
3055
{1o}
EN
3054
Limit 1 phase
Grenzwert 1-phasig
{0}
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Mains phase shift: Threshold value 1 phase
3 to 30
If the electrical angle of the mains voltage shifts more than this configured value in
any single phase, an alarm with the class configured in parameter 3051 is initiated.
Depending on the configured mains decoupling procedure (parameter 3110 on
page 85), the GCB, MCB, or an external CB will be opened.
Mains phase shift: Threshold value 3 phase
3 to 30
If the electrical angle of the mains voltage shifts more than this configured value in
all three phases, an alarm with the class configured in parameter 3051 is initiated.
Depending on the configured mains decoupling procedure (parameter 3110 on
page 85), the GCB, MCB, or an external CB will be opened.
Mains phase shift: Alarm class
Class A/B/C/D/E/F

Page 96/339
Woodward
DE
EN
Manual 37427
CL2
3052
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3056
Mains phase shift: Self acknowledgment
Yes / No
no longer detected.
Mains phase shift: Delayed engine speed
Yes / No
NOTE
The mains phase shift configuration parameters are located below the mains decoupling function
menu on the display.
Woodward
Page 97/339
Manual 37427
Configure Monitoring: Mains, Voltage Phase Rotation - {2oc}
CAUTION
Please ensure during installation that all voltages applied to this unit are wired correctly to both sides
of the circuit breaker. Failure to do so may result in damage to the control unit and/or generation
equipment due to closing the breaker asynchronous or with mismatched phase rotations and phase
rotation monitoring enabled at all connected components (engine, generator, breakers, cable, busbars,
etc.).
This function may block a connection of systems with mismatched phases systems only under the
following conditions:
The voltages being measured are wired correctly with respect to the phase rotation at the
measuring points (i.e. the voltage transformer in front and behind the circuit breaker)
The measuring voltages are wired without angular phase shift or interruption from the measuring
point to the control unit
The measuring voltages are wired to the correct terminals of the control unit (i.e. L1 of the
generator is connected with the terminal of the control unit which is intended for the L1 of the
generator)
The LogicsManager function "Enable MCB" (refer to parameter 12923 on page 155) is false in case
of a incorrect rotation field
the mains or the generator. The voltage phase rotation alarm checks the phase rotation of the voltages and the
configured phase rotation to ensure they are identical. The directions of rotation are differentiated as "clockwise"
and "counter clockwise". With a clockwise field the direction of rotation is "L1-L2-L3"; with a counter clockwise
field the direction of rotation is "L1-L3-L2". If the control is configured for a clockwise rotation and the voltages
into the unit are calculated as counterclockwise the alarm will be initiated. The direction of configured rotation
being monitored by the control unit is displayed on the screen.
If this protective function is triggered, the display indicates "Mns.ph.rot. mismatch" and the logical
Parameter table
Level
Text
Setting range
Mains voltage phase direction fault (the hysteresis is 0.7 % of the rated value)
Monitoring
On / Off
Mains phase rotation
CW / CCW
Alarm class
A/B
Self acknowledgment
Yes / No
Yes / No
Default value
On
CW
B
No
No
Table 3-34: Monitoring - standard values - mains voltage phase rotation
NOTE
This monitoring function is only enabled if Mains voltage measuring (parameter 1853) is configured to
"3Ph 4W" or "3Ph 3W" and the measured voltage exceeds 50 % of the rated voltage (parameter 1768) or
if Mains voltage measuring (parameter 1853) is configured to "1Ph 2W" (in this case, the phase rotation
is not evaluated, but defined by the 1Ph2W phase rotation (parameter 1859)).
Page 98/339
Woodward
DE
EN
Manual 37427
CL2
{0}
DE
CL2
{0}
{1o}
DE
CL2
3971
{1oc}
{2oc}
Mains phase rotation

Netzdrehfeld
EN
3974
{1o}
EN
3970
Monitoring
berwachung
{0}
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Mains voltage phase rotation: Monitoring
On / Off
On ................ Phase rotation monitoring is carried out according to the following

parameters
Off ............... No monitoring is carried out.
Mains voltage phase rotation: Direction
CW / CCW
CW .............. The three-phase measured mains voltage is rotating CW (clockwise; that means the voltage rotates in L1-L2-L3 direction; standard
setting).
CCW ........... The three-phase measured mains voltage is rotating CCW (counter
clock-wise; that means the voltage rotates in L1-L3-L2 direction).
Mains voltage phase rotation: Alarm class
Class A/B/C/D/E/F
CAUTION:
If an alarm class that leads to an engine shutdown (alarm class C or
higher) is configured into this parameter, a main phase rotation alarm may
lead to a genset shutdown due to an alarm of class C or higher.
DE
EN
CL2
3972
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3973
Woodward
Mains voltage phase rotation: Self acknowledgment
Yes / No
no longer detected.
No ................ The control does not automatically reset the alarm when the fault
Mains voltage phase rotation: Engine delayed monitoring
Yes / No
No ................ Monitoring for this fault condition is continuously enabled
Page 99/339
Manual 37427
Configure Monitoring: Engine

Configure Monitoring: Engine, Overspeed (Levels 1 & 2) ANSI# 12
The speed measured by the magnetic pickup unit (MPU) is monitored for overspeed. If the MPU is disabled, the
speed may only be monitored using the generator overfrequency monitoring. If the MPU speed exceeds the
overspeed limits the configured alarms will be initiated.
If this protective function is triggered, the display indicates "Overspeed 1" or "Overspeed 2" and the
logical command variable "05.01" or "05.02" will be enabled.
Parameter table
Level
Text
Engine overspeed (the hysteresis is 50 min-1).
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment

thresholds.
Setting range
Default value
On / Off
0 to 9,999 RPM
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
0 to 9,999 RPM
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On
1,850 RPM
1.00 s
B
No
No
On
1,900 RPM
0.10 s
F
No
No
DE
EN
Table 3-35: Monitoring - standard values - engine overspeed
CL2
{0}
{1o}
DE
EN
2100
2106
CL2
{0}
{1o}
DE
EN
2104
2110
CL2
{0}
{1o}
DE
EN
2105
2111
CL2
2101
2107
{0}
{1o}
Page 100/339
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Engine overspeed: Monitoring (Level 1/Level 2)
On / Off
On ................ Overspeed monitoring is carried out according to the following

> Level 2).
Engine overspeed: Threshold value (Level 1/Level 2)
0 to 9,999 RPM
The threshold values that are to be monitored are defined here. If the monitored
engine speed reaches or exceeds this value for at least the delay time without
Engine overspeed: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored engine speed exceeds the threshold value for the delay time
configured here, an alarm will be issued. If the monitored engine speed falls below
the threshold (minus the hysteresis) before the delay expires the time will be reset.
Engine overspeed: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

Woodward
DE
EN
Manual 37427
CL2
2102
2108
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2103
2109
Woodward
Engine overspeed: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Engine overspeed: Engine delayed monitoring (Level 1/Level 2)
Yes / No
Page 101/339
Manual 37427
Configure Monitoring: Engine, Underspeed (Levels 1 & 2)

The speed measured by the magnetic pickup unit (MPU) is monitored for underspeed. If the MPU is disabled, the
speed may only be monitored using the generator underfrequency monitoring. If the MPU speed falls below the
underspeed limits the configured alarms will be initiated.
If this protective function is triggered, the display indicates "Underspeed 1" or "Underspeed 2" and the
logical command variable "05.03" or "05.04" will be enabled.
Parameter table
Level
Text
Engine underspeed (the hysteresis is 50 min-1)
Level 1
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Level 2
Monitoring
Limit
Delay
Alarm class
Self acknowledgment

thresholds.
Setting range
On / Off
0 to 9,999 RPM
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
On / Off
0 to 9,999 RPM
0.02 to 99.99 s
A/B/C/D/E/F
Yes / No
Yes / No
Default value
On
1,300 RPM
1.00 s
B
No
Yes
On
1,250 RPM
0.10 s
F
No
Yes
DE
EN
Table 3-36: Monitoring - standard values - engine underspeed
CL2
{0}
{1o}
DE
EN
2150
2156
CL2
{0}
{1o}
DE
EN
2154
2160
CL2
{0}
{1o}
DE
EN
2155
2161
CL2
2151
2157
{0}
{1o}
Page 102/339
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Engine underspeed: Monitoring (Level 1/Level 2)
On / Off
On ................ Underspeed monitoring is carried out according to the following

> Level 2).
Engine underspeed: Threshold value (Level 1/Level 2)
0 to 9,999 RPM
engine speed reaches or falls below this value for at least the delay time without
Engine underspeed: Delay (Level 1/Level 2)
0.02 to 99.99 s
If the monitored engine speed falls below the threshold value for the delay time
configured here, an alarm will be issued. If the monitored engine speed exceeds
the threshold (plus the hysteresis) again before the delay expires the time will be
reset.
Engine underspeed: Alarm class (Level 1/Level 2)
Class A/B/C/D/E/F

Woodward
DE
EN
Manual 37427
CL2
2152
2158
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
2153
2159
Woodward
Engine underspeed: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Engine underspeed: Engine delayed monitoring (Level 1/Level 2)
Yes / No
Page 103/339
Manual 37427
Configure Monitoring: Engine/Generator, Speed Detection (Speed/Frequency Mismatch)

Speed detection checks if the generator voltage frequency f (determined from the measured generator voltage)
differs from the measured engine speed n (determined from the Pickup signal) and determines a difference (f-n).
If the two frequencies are not identical (f-n 0) and the monitored frequency mismatch reaches or exceeds the
threshold, an alarm is output. Additionally the LogicsManager output "Firing speed" is checked upon its logical
status with respect to the measuring values "generator frequency" and "Pickup speed".
If this protective function is triggered, the display indicates "Speed/freq. mismatch" and the logical
NOTE
Speed/frequency mismatch (n/f mismatch) is carried out only if an MPU is connected to the control and
parameter "Speed pickup" (parameter 1600 on page 187), is configured On. The following is valid:
The measurement via Pickup is disabled (Off):

Mismatch monitoring is carried out using the generator frequency and the LogicsManager. If
the LogicsManager output is enabled and the frequency is outside of the configured limit, an
alarm will be issued.
[Hz]
t[min-SP]
The measurement via Pickup is enabled (On):

Mismatch monitoring is carried out using the engine speed from the Pickup and the generator
frequency. If the speed/frequency mismatch or the LogicsManager is enabled and the
frequency is outside of the configured limit, an alarm will be issued.
t[min-SP]
Limit SP
SPHysteresis
Activation
Frequency
[f-n = 0 Hz]
Monitoring
active
(Requirement: delayed
engine monitoring active)
Activation
frequency
reached
Alarm
Figure 3-12: Monitoring - plausibility check n/f
Page 104/339
Woodward
Manual 37427
Parameter table
Level
Text
Setting range
Speed detection (speed/frequency mismatch) (the hysteresis is 50 RPM).
Monitoring
On / Off
Speed/frequency mismatch limit
1.5 to 8.5 Hz
Delay
0.02 to 99.99 s
Activation frequency
15 to 85 Hz
Alarm class
A/B/C/D/E/F
Self acknowledgment
Yes / No
Default value
On
5.0 Hz
2.00 s
20 Hz
E
No
DE
EN
Table 3-37: Monitoring - standard values - plausibility control n/f
CL2
2450
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
DE
EN
Speed/frequency mismatch limit

Zulssige Differenz
CL2 {0} {1o} {1oc} {2oc}
2454
n/f/LogicsManager mismatch: Monitoring
On / Off
On................. Monitoring of the speed/frequency/LogicsManager mismatch

(n/f/LM mismatch) is carried out according to the following
parameters.
Off ................ Monitoring is disabled.
n/f/LogicsManager mismatch: Threshold value
1.5 to 8.5 Hz
The frequency mismatch that is to be monitored is defined here. If the monitored

frequency mismatch reaches or exceeds this value for at least the delay time
without interruption, the action specified by the alarm class is initiated.
DE
EN
The LogicsManager is monitored with respect to his status.
CL2
{0}
DE
CL2
{0}
{1o}
DE
CL2
2451
{1oc}
{2oc}
Activation frequency
berwachung ab
EN
2453
{1o}
EN
2455
Delay
Verzgerung
{0}
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
n/f/LogicsManager mismatch: Delay
0.02 to 99.99 s
If the monitored frequency mismatch exceeds the threshold value for the delay
time configured here, an alarm will be issued. If the monitored frequency
mismatch falls below the threshold (minus the hysteresis) before the delay expires
the time will be reset.
n/f/LogicsManager mismatch: Start-up frequency
15 to 85 Hz
The speed/frequency mismatch monitoring is enabled at this generator frequency.

n/f/LogicsManager mismatch: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
2452
{0}
Woodward
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
n/f/LogicsManager mismatch: Self acknowledgment
Yes / No
Yes ................ The control automatically clears the alarm if the fault condition is no
longer detected.
Page 105/339
Manual 37427
Configure Monitoring: Engine, Generator Active Power Mismatch

If enabled, this monitoring function becomes only active if generator power control is enabled (refer to Configure
Application: Controller, Load Control on page 223 for more information). If the measured generator power
deviates from the power set point by a value exceeding the limit configured in parameter 2925 for a time
exceeding the delay configured in parameter 2923, an alarm will be issued.
If this protective function is triggered, the display indicates "Gen act.pwr mismatch" and the logical
Parameter table
Level
Text
Generator active power mismatch
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
0.0 to 30.0%
3 to 65000 s
A/B/C/D/E/F
Yes / No
On
5.0 %
30 s
B
No
DE
EN
Table 3-38: Monitoring - standard values - generator active power mismatch
CL2
{0}
{1o}
DE
EN
2920
CL2
2925
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Generator active power mismatch: Monitoring
On / Off
On .................Monitoring of the generator active power mismatch is carried out

according to the following parameters.
Generator active power mismatch: Threshold value
0.0 to 30.0 %
This value refers to the generator rated active power (parameter 1752on
page 38).
DE
EN
If the difference between the measured generator power and the power set point
exceeds this value for at least the delay time (parameter 2923) without interruption,
the action specified by the alarm class is initiated.
CL2
{0}
{1o}
DE
EN
2923
CL2
2921
{0}
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Generator active power mismatch: Delay
3 to 65000 s
If the monitored active power mismatch exceeds the threshold value configured in
parameter 2925 for the delay time configured here, an alarm will be issued. If the
monitored active power mismatch falls below the threshold (minus the hysteresis)
Generator active power mismatch: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
2922
{0}
Self acknowledge
Selbstquittierend
{1o}
Page 106/339
{1oc}
{2oc}
Generator active power mismatch: Self acknowledge
Yes / No
longer detected.
Woodward
Manual 37427
Configure Monitoring: Engine, Mains Active Power Mismatch

If enabled, this monitoring function becomes only active if generator power control is enabled and the active
power set point is configured to "Import" or "Export" (refer to Configure Application: Controller, Load Control
on page 223 for more information). If the measured import or export power deviates from the power set point by
a value exceeding the limit configured in parameter 2935 for a time exceeding the delay configured in
parameter 2933, an alarm will be issued.
If this protective function is triggered, the display indicates "Mns act.pwr mismatch" and the logical
Parameter table
Level
Text
Mains active power mismatch
Monitoring
Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
1.0 to 99.9%
3 to 65000 s
A/B/C/D/E/F
Yes / No
On
5.0 %
30 s
B
No
DE
EN
Table 3-39: Monitoring - standard values - mains active power mismatch
CL2
{0}
{1o}
DE
EN
2930
CL2
2935
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Mains active power mismatch: Monitoring
On / Off
On ................ Monitoring of the mains active power mismatch is carried out

according to the following parameters.
Mains active power mismatch: Threshold value
1.0 to 99.9 %
This value refers to the mains rated active power (parameter 1748on
page 38).
DE
EN
If the difference between the measured import or export power and the power set
point exceeds this value for at least the delay time (parameter 2933) without
CL2
{0}
{1o}
DE
EN
2933
CL2
2931
{0}
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Mains active power mismatch: Delay
3 to 65000 s
If the monitored active power mismatch exceeds the threshold value configured in
parameter 2935 for the delay time configured here, an alarm will be issued. If the
monitored active power mismatch falls below the threshold (minus the hysteresis)
Mains active power mismatch: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
2932
{0}
Woodward
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Mains active power mismatch: Self acknowledge
Yes / No
Yes ............... The control automatically clears the alarm if the fault condition is no
longer detected.
Page 107/339
Manual 37427
Configure Monitoring: Engine, Generator Unloading Mismatch

This monitoring function is always enabled and becomes active when a stop command is issued. Following a stop
command, the controller tries to reduce the power before opening the GCB. If the power falls below the unload
limit (parameter 3125) before the delay (parameter 3123) expires, a "GCB open" command will be issued. If the
controller fails to reduce the power to fall below the unload limit (parameter 3125) before the delay
(parameter 3123) expires, a "GCB open" command will be issued together with an alarm.
If this protective function is triggered, the display indicates "Gen. unloading fault" and the logical
Parameter table
Level
Text
Generator unloading mismatch
Unload Limit
Delay
Alarm class
Self acknowledgment
Setting range
Default value
0.5 to 99.9%
2 to 9999 s
A/B/C/D/E/F
Yes / No
3.0 %
60 s
B
No
Table 3-40: Monitoring - standard values - generator unloading mismatch
DE
EN
Unload Limit
Abschaltleistung
CL2
3125
{0}
{1o}
{1oc}
{2oc}
Generator unloading mismatch: Threshold value
0.5 to 99.9 %
This value refers to the generator rated active power (parameter 1752on
page 38).
DE
EN
If the monitored generator power falls below this value, a "GCB open" command
will be issued.
CL2
{0}
{1o}
DE
EN
3123
CL2
3121
{0}
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Generator unloading mismatch: Delay
2 to 9999 s
If the monitored generator power does not fall below the limit configured in
parameter 3125 before the time configured here expires, a "GCB open" command
will be issued together with an alarm.
Generator unloading mismatch: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
3122
{0}
Self acknowledge
Selbstquittierend
{1o}
Page 108/339
{1oc}
{2oc}
Generator unloading mismatch: Self acknowledge
Yes / No
longer detected.
Woodward
Manual 37427
Configure Monitoring: Engine, Start Failure

If it is not possible to start the engine within a configured number of start attempts (refer to Configure
Application: Configure Engine, Start/Stop on page 182), an alarm will be initiated.
If this protective function is triggered, the display indicates "Start fail" and the logical command variable
"05.08" will be enabled.
Parameter table
Level
Text
Engine start failure
Monitoring
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
A/B/C/D/E/F
Yes / No
On
F
No
DE
EN
Table 3-41: Monitoring - standard values - engine start failure
CL2
{0}
{1o}
DE
EN
3303
CL2
3304
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Start failure: Monitoring
On / Off
On ................ Monitoring of the start sequence is carried out according to the

Startup failure: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
3305
{0}
Woodward
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Start failure: Self acknowledgment
Yes / No
longer detected.
Page 109/339
Manual 37427
Configure Monitoring: Engine, Shutdown Malfunction

If it is not possible to stop the engine within a configured time, an alarm will be initiated.
If this protective function is triggered, the display indicates "Eng. stop malfunct." and the logical
Parameter table
Level
Text
Engine shutdown malfunction
Monitoring
Maximal stop delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
3 to 999 s
A/B/C/D/E/F
Yes / No
On
30 s
F
No
DE
EN
Table 3-42: Monitoring - standard values - engine shutdown malfunction
CL2
DE
EN
2500
CL2
{1o}
{0}
{1o}
DE
CL2
2501
{1oc}
{2oc}
Maximal stop delay

Verzgerung Abstellstrung
EN
2503
{0}
Monitoring
berwachung
{0}
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Stop failure: Monitoring
On / Off
On .................Monitoring of the stop sequence is carried out according to the

Stop failure: Delay
3 to 999 s
The maximum permissible time between the output of a stop command and the
reply that the engine is stopped successfully is defined here. If the engine cannot be
stopped within this time (this means speed via the Pickup, frequency via the
generator voltage, or the LogicsManager is detected) the action specified by the
alarm class is initiated.
Stop failure: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
2502
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Stop failure: Self acknowledgment
Yes / No
longer detected.
NOTE
We recommend to assign this monitoring function to a discrete output to be able to shutdown the
engine with an external device to provide a shutdown redundancy.
Page 110/339
Woodward
Manual 37427
Configure Monitoring: Engine, Unintended Stop

If an engine stop has been detected without a stop command being issued, an alarm will be initiated.
If this protective function is triggered, the display indicates "Unintended stop" and the logical command
variable "05.05" will be enabled.
Parameter table
Level
Text
Engine unintended stop
Monitoring
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
A/B/C/D/E/F
Yes / No
On
F
No
DE
EN
Table 3-43: Monitoring - standard values - engine unintended stop
CL2
{0}
{1o}
DE
EN
2650
CL2
2651
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Unintended stop: Monitoring
On / Off
On ................ Monitoring of an unintended stop is carried out according to the

Unintended stop: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
2657
{0}
Woodward
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Unintended stop: Self acknowledge
Yes / No
longer detected.
Page 111/339
Manual 37427
Configure Monitoring: Engine, Operating Range Failure

The operating range failure monitoring issues an alarm if one of the following conditions is fulfilled:
Check 1: The easYgen tries to close the GCB, but the generator is not within its operating range
(parameters 5800, 5801, 5802, or 5803 on page 48)
Check 2: The easYgen tries to synchronize the GCB, but the busbar or the generator is not within the
generator operating range (parameters 5800, 5801, 5802, or 5803 on page 48)
Check 3: The easYgen tries to close the GCB to the dead busbar, but the busbar voltage is NOT below the
dead busbar detection limit (parameter 5820 on page 148)
Check 4: The easYgen tries to synchronize the GCB, the MCB is closed, but the mains are not within the
mains operating range (parameters 5810, 5811, 5812, or 5813 on page 83)
Check 5: The easYgen tries to close the GCB, the MCB is closed, but the busbar is dead
No alarm will be issued in idle mode. This monitoring function is disabled below firing speed.
If this protective function is triggered, the display indicates "Operat. range failed" and the logical
Parameter table
Level
Text
Operating range failure
Monitoring
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
1 to 999 s
A/B/C/D/E/F
Yes / No
On
30 s
B
No
DE
EN
Table 3-44: Monitoring - standard values - engine dead bus operation
CL2
{0}
{1o}
DE
EN
2660
CL2
{0}
{1o}
DE
EN
2663
CL2
2661
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Operating range failure: Monitoring
On / Off
On .................Monitoring of the operating range is carried out according to the

Operating range failure: Delay
1 to 999 s
If one of the above mentioned conditions for an operating range failure is fulfilled,
an alarm will be issued. If the respective condition is not fulfilled anymore before
the delay time expires, the delay time will be reset.
Operating range failure: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
2662
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Operating range failure: Self acknowledge
Yes / No
longer detected.
CAUTION
If load-dependent start/stop (refer to Configure Application: Automatic, Load-Dependent Start/Stop on
page 193) is enabled, this monitoring function must be configured with a shutdown alarm class (C, D,
E, or F) or disable load-dependent start/stop if triggered to ensure that the next engine will be started.
Page 112/339
Woodward
Manual 37427
Configure Monitoring: Engine, Charge Alternator (D+)

The charge alternator monitoring issues an alarm if the voltage measured at the auxiliary excitation input D+
(terminal 52) falls below a fix limit. The fix limit depends on the power supply voltage. If a power supply voltage
exceeding 16 V is detected, the unit assumes a 24 V system and uses a limit of 20 V. If a power supply voltage
below 16 V is detected, the unit assumes a 12 V system and uses a limit of 9 V.
If this protective function is triggered, the display indicates "Charge alt. low volt" and the logical
Parameter table
Level
Text
Engine charge alternator
Monitoring
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
2 to 9999 s
A/B/C/D/E/F
Yes / No
Yes / No
Off
10 s
B
No
Yes
DE
EN
Table 3-45: Monitoring - standard values - engine charge alternator failure
CL2
{0}
{1o}
DE
EN
4050
CL2
{0}
{1o}
DE
EN
4055
CL2
4051
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Charge alternator failure: Monitoring
On / Off
On ................ Monitoring of the charge alternator is carried out according to the

Charge alternator failure: Delay
2 to 9999 s
If the voltage measured at the auxiliary excitation input D+ falls below a fixed limit
for the time defined here, an alarm will be issued. If the voltage returns within the
limit before the delay time expires, the delay time will be reset.
Charge alternator failure: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
4052
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

Verzgert durch Motordrehz.
CL2 {0} {1o} {1oc} {2oc}
4053
Woodward
Charge alternator failure: Self acknowledge
Yes / No
longer detected.
Charge alternator failure: Engine delayed monitoring (Level 1/Level 2)
Yes / No
Yes ............... Monitoring for fault conditions is not performed until engine delayed
monitoring is enabled. The engine monitoring delay time
No ................. Monitoring for this fault condition is continuously enabled regardless
of engine speed.
Page 113/339
Manual 37427
Configure Monitoring: Breaker Monitoring

Configure GCB
Circuit breaker monitoring contains two alarms: A breaker reclose alarm and a breaker open alarm.
Reclose Alarm: If the control initiates a close of the breaker and the breaker fails to close after the configured
number of attempts the monitoring CB alarm will be initiated (refer to parameter "GCB maximum closing
attempts", parameter 3418 on page 114).
If this protective function is triggered, the display indicates "GCB fail to close" and the logical command
Breaker Open Alarm: If the control is attempting to open the circuit breaker and it fails to see that the CB is
open within the configured time in seconds after issuing the breaker open command then the monitoring CB
alarm will be initiated (refer to parameter "GCB open monitoring", parameter 3420 on page 114).
If this protective function is triggered, the display indicates "GCB fail to open" and the logical command
Parameter table
Level
Text
Breaker monitoring - GCB
Monitoring
GCB alarm class
GCB maximum closing attempts
GCB open monitoring
Setting range
Default value
On / Off
A/B/C/D/E/F
1 to 10
0.10 to 5.00 s
On
C
5
2s
Table 3-46: Monitoring - standard values - breaker monitoring - GCB
DE
EN
GCB monitoring
GLS berwachung
CL2
{0}
---
{1o}
DE
CL2
2601
{0}
---
{1oc}
{2oc}
GCB alarm class

GLS Alarmklasse
EN
2600
{1o}
{1oc}
{2oc}
Circuit breaker monitoring GCB: Monitoring
On / Off
On ................ Monitoring of the GCB is carried out according to the following

parameters.
Circuit breaker monitoring GCB: Alarm class
Class A/B/C/D/E/F

DE
EN
DE
EN
GCB maximum closing attempts

GLS ZU max. Schaltversuche
{1o}
{1oc} {2oc}
CL2 {0}
----3418
CL2
3420
GCB open monitoring

GLS AUF berwachung
{0}
---
{1o}
{1oc}
{2oc}
Breaker monitoring GCB: Max. "GCB close" attempts
1 to 10
The maximum number of breaker closing attempts is configured in this parameter

(relay output "Command: close GCB"). When the breaker reaches the configured
number of attempts, a "GCB fail to close" alarm is issued. The counter for
the closure attempts will be reset as soon as the "Reply GCB" is de-energized for
at least 5 seconds to signal a closed GCB.
Breaker monitoring GCB: Max. time until reply "GCB open"
0.10 to 5.00 s
If the "Reply GCB" is not detected as energized once this timer expires, a "GCB
fail to open" alarm is issued. This timer initiates as soon as the "open
breaker" sequence begins. The alarm configured in parameter 2601 is issued.
CAUTION
Page 114/339
Woodward
Manual 37427
Configure Synchronization GCB

Parameter table
Level
Text
Breaker monitoring - GCB synchronization
Monitoring
Timeout
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
3 to 999 s
A/B/C/D/E/F
Yes / No
On
60 s
B
No
DE
EN
Table 3-47: Monitoring - standard values - breaker monitoring - GCB synchronization
CL2
{0}
{1o}
DE
EN
3060
CL2
{0}
{1o}
DE
EN
3063
CL2
3061
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Timeout
Mindestzeit
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Synchronization GCB: Monitoring
On / Off
On ................ Monitoring of the GCB synchronization is carried out according to

the following parameters.
Synchronization GCB: Timeout
3 to 999 s
If it was not possible to synchronize the GCB within the time configured here, an
alarm will be issued. The message "GCB syn. timeout" is issued and the logical
Synchronization GCB: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
3062
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
Synchronization GCB: Self acknowledge
Yes / No
longer detected.
CAUTION
Woodward
Page 115/339
Manual 37427
Configure MCB {2oc}
NOTE
If an alarm is detected when attempting to close the MCB, an emergency power operation will be
carried out if the "Emergency start with MCB failure" is On.
If an alarm class higher than 'B' class has been selected it will not be possible to start the engine with
the setting "Emergency start with MCB failure" (parameter 3408 on page 190) = configured as On in an
emergency power condition.
Circuit breaker monitoring contains two alarms: A breaker reclose alarm and a breaker open alarm.
Reclose Alarm: If the control initiates a close of the breaker and the breaker fails to close after the configured
number of attempts the monitoring CB alarm will be initiated.
(Refer to parameter "MCB maximum closing attempts", parameter 3419 on page 117).
If this protective function is triggered, the display indicates "MCB fail to close" and the logical command
Breaker Open Alarm: If the control is attempting to open the circuit breaker and it fails to see that the CB is
open within the configured time in seconds after issuing the breaker open command then the monitoring CB
alarm will be initiated.
(Refer to parameter "MCB open monitoring", parameter 3421 on page 117).
If this protective function is triggered, the display indicates "MCB fail to open" and the logical command
The alarm classes have the following influence to the function of the unit.
Fault at 'closing the MCB'
Alarm classes A & B:
Parameter 2802 on page 190 "Emergency run" = Off
If the MCB cannot be closed, the busbar remains without voltage, until the MCB breaker fault is
acknowledged. The control continues attempting to close the MCB.
Parameter 2802 on page 190 "Emergency run" = On, parameter 3408 on page 190 "Emergency start with
MCB failure" = Off
If the MCB cannot be closed, the busbar remains without voltage, until the MCB breaker fault is
acknowledged. The control continues attempting to close the MCB.
Parameter 2802 on page 190 "Emergency run" = On, parameter 3408 on page 190 "Emergency start with
MCB failure" = On
If the MCB cannot be closed, an emergency power operation is initiated (the engine is started and the GCB
is closed; the busbar is supplied by the generator). If the alarm is acknowledged and if the MCB can be
closed, the load is switched to mains supply and the emergency power operation terminates.
Fault at 'opening the MCB'
This fault is processed according to the action described within the alarm classes. As long as the reply is
present that the MCB is still closed, the GCB cannot be closed.
Parameter table
Level
Text
Breaker monitoring - MCB
Monitoring
MCB alarm class
MCB maximum closing attempts
MCB open monitoring
Setting range
Default value
On / Off
A/B/C/D/E/F
1 to 10
0.10 to 5.00 s
On
B
5
2s
Table 3-48: Monitoring - standard values - breaker monitoring - MCB
Page 116/339
Woodward
DE
Manual 37427
CL2
{0}
---
DE
EN
2620
CL2
2621
{0}
---

MCB monitoring
NLS berwachung
{1o}
---
{1oc}
---
{2oc}
MCB alarm class

NLS Alarmklasse
{1o}
---
{1oc}
---
{2oc}
Circuit breaker monitoring MCB: Monitoring
On / Off
On ................ Monitoring of the MCB is carried out according to the following

parameters.
Off ............... Monitoring is disabled.
Circuit breaker monitoring MCB: Alarm class
Class A/B

DE
EN
DE
EN
MCB maximum closing attempts

NLS ZU max. Schaltversuche
{1o}
{1oc} {2oc}
CL2 {0}
------3419
CL2
3421
MCB open monitoring

NLS AUF berwachung
{0}
---
Woodward
{1o}
---
{1oc}
---
{2oc}
Breaker monitoring MCB: Max. "MCB close" attempts
1 to 10
The maximum number of breaker closing attempts is configured in this parameter

(relay output "Command: close MCB"). When the breaker reaches the configured
number of attempts, an "MCB fail to close" alarm is issued. The counter
for the closure attempts will be reset as soon as the "Reply MCB" is de-energized
for at least 5 seconds to signal a closed MCB.
Breaker monitoring MCB: Max. time until reply "MCB open"
0.10 to 5.00 s
If the "Reply MCB" is not detected as energized once this timer expires, an "MCB
fail to open" alarm is issued. This timer initiates as soon as the "open
breaker" sequence begins. The alarm configured in parameter 2621 is issued.
Page 117/339
Manual 37427
Configure Synchronization MCB

Parameter table
Level
Text
Breaker monitoring - MCB synchronization
Monitoring
Timeout
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
3 to 999 s
A/B/C/D/E/F
Yes / No
On
60 s
B
No
DE
EN
Table 3-49: Monitoring - standard values - breaker monitoring - MCB synchronization
CL2
{0}
{1o}
DE
EN
3070
CL2
{0}
{1o}
DE
EN
3073
CL2
3071
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Timeout
Mindestzeit
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Synchronization MCB: Monitoring
On / Off
On .................Monitoring of the MCB synchronization is carried out according to

the following parameters.
Synchronization MCB: Timeout
3 to 999 s
If it was not possible to synchronize the MCB within the time configured here, an
alarm will be issued. The message "MCB syn. timeout" is issued and the logical
Synchronization MCB: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
3072
{0}
Self acknowledge
Selbstquittierend
{1o}
Page 118/339
{1oc}
{2oc}
Synchronization MCB: Self acknowledge
Yes / No
longer detected.
Woodward
Manual 37427
Configure Monitoring: Breakers, Generator / Busbar / Mains Phase Rotation - {2oc}

the mains or the generator. The voltage phase rotation alarm checks, if the phase rotation of the measured voltage
systems are identical. If the control detects different phase rotations of mains and generator, the alarm will be
initiated and a breaker synchronization is inhibited. However, this alarm will not prevent a dead busbar closure,
i.e. a dead bus start.
If this protective function is triggered, the display indicates "Ph.rotation mismatch" and the logical
Parameter table
Level
Text
Phase rotation fault (the hysteresis is 0.7 % of the rated value)
Monitoring
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
A/B/C/D/E/F
Yes / No
On
B
Yes
Table 3-50: Monitoring - standard values - mains voltage phase rotation
NOTE
DE
EN
This monitoring function is only enabled if Generator voltage measuring (parameter 1851) and Mains
voltage measuring (parameter 1853) are configured to "3Ph 4W" or "3Ph 3W" and the measured voltage
exceeds 50 % of the rated voltage (parameter 1766) or if Generator voltage measuring (parameter 1851)
and Mains voltage measuring (parameter 1853) are configured to "1Ph 2W" (in this case, the phase
rotation is not evaluated, but defined by the 1Ph2W phase rotation (parameter 1859)).
CL2
{0}
---
{1o}
---
DE
EN
2940
CL2
2941
{0}
---
{1o}
---
Monitoring
berwachung
{1oc}
---
{2oc}
Alarm class
Alarmklasse
{1oc}
---
{2oc}
Generator /Busbar / Mains phase rotation: Monitoring
On / Off
On ................ Phase rotation monitoring is carried out according to the following

parameters
Generator /Busbar / Mains phase rotation: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
2942
{0}
---
Woodward
Self acknowledge
Selbstquittierend
{1o}
---
{1oc}
---
{2oc}
Generator /Busbar / Mains phase rotation: Self acknowledgment
Yes / No
longer detected.
Page 119/339
Manual 37427
Configure Monitoring: Flexible Limits

CAUTION
Flexible Limits must not be used for protective functions, because the monitoring function is not
guaranteed beyond an exceeding of 320 %.
CAUTION
It is not possible to monitor temperature values in Degree Fahrenheit and pressure values in psi. Even
if the parameters 3631 or 3630 on page 156 are configured to a value display in F or psi, flexible limit
monitoring always refers to the value in Degree Celsius or bar.
This control offers 16 flexible limits. They may be used for "limit switch" functions of all measured analog
values. It is possible to choose between alarm (warning and shutdown) and control operation via the
LogicsManager.
If an alarm class is triggered, the display indicates "Flexible limit {x}", where {x} indicates the flexible
limit 1 to 16, or the text configured using ToolKit and the logical command variable "15.{x}" will be enabled.
The following parameter description refers to flexible limit 1. The flexible limits 2 through 16 are configured
accordingly. The parameter IDs of the flexible limits 2 through 16 are listed in Table 3-54 on page 123.
NOTE
The flexible limits 13 through 16 are disabled during idle mode operation (refer to Configure
Application: Configure Engine, Idle Mode on page 188).
Parameter table
Level
Text
Flexible limits monitoring
Description
Monitoring
Monitored data source
Monitoring at
Limit
Hysteresis
Delay
Alarm class
Self acknowledgment
Setting range
Default value
user-defined
On / Off
[data source]
Overrun / Underrun
-32000 to 32000
0 to 32000
0.02 to 327.00 s
A/B/C/D/E/F/Control
Yes / No
Yes / No
Flex. limit {x}

Off
Overrun
100
1
1s
B
No
No
Table 3-51: Monitoring - standard values - flexible limits
The flexible limits must be used to monitor analog inputs like oil pressure or coolant temperature for example.
We recommend to change the flexible limit description accordingly. Refer to Table 3-52 for configuration
examples. Naturally, the analog inputs must be configured accordingly.
Configuration example Parameter
Description
Monitoring
Monitoring at
Limit
Hysteresis
Delay
Alarm class
Self acknowledgment
example for low oil pressure

monitoring
Oil pressure
On
06.01 Analog input 1
Underrun
200 (2.00 bar)
10
0.50 s
F
No
Yes
example for high coolant

temperature monitoring
Coolant temp.
On
Overrun
80 (80 C)
2
3s
B
No
No
Table 3-52: Monitoring - flexible limit examples
Page 120/339
Woodward
DE
EN
Manual 37427
CL2
T
{0}
{1o}

Description
Beschreibung
{1oc}
{2oc}
4208
FlexLimit {x} [x = 1 to 16]: Description
user-defined
A description for the respective flexible limit may be entered here. The description
may have 4 through 16 characters and is displayed instead of the default text if this
limit is exceeded.
DE
EN
Note: This parameter may only be configured using ToolKit configuration software
CL2
DE
EN
4200
CL2
4206
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}

berwachte Datenquelle
{0}
{1o}
{1oc}
{2oc}
FlexLimit {x} [x = 1 to 16]: Monitoring
On / Off
On ................ Monitoring of the limit {x} is carried out according to the following
parameters.
FlexLimit {x} [x = 1 to 16]: Monitored data source
[data source]
Any possible data source may be selected. Use the and softkeys to scroll
through the list of variables and confirm your selection with the softkey. Refer to
Appendix C: Data Sources on page 305 for a list of all data sources.
These are for example:
00.05 Analog input D+
01.24 Generator total power
02.14 Mains current L1
DE
EN
Figure 3-13: Monitoring - flexible limits - data source selection
CL2
4204
{0}
Woodward
Monitoring at
berwachung auf
{1o}
{1oc}
{2oc}
FlexLimit {x} [x = 1 to 16]: Monitoring for
Overrun / Underrun
Overrun ....... The monitored value must exceed the threshold limit for a fault to be
recognized.
Underrun..... The monitored value must fall below the threshold limit for a fault to
be recognized.
Page 121/339
DE
EN
Manual 37427
CL2
4205
{0}
{1o}

Limit
Grenzwert
{1oc}
{2oc}
FlexLimit {x} [x = 1 to 16]: Threshold
-32000 to 32000
The threshold limit of the value to be monitored is defined by this parameter. If this
value is reached or exceeded / fallen below (dependent on parameter 4204) for at
least the delay time configured in parameter 4207 the action specified by the alarm
class is initiated after the configured delay expires.
The entry format of the threshold depends on the respective analog value.
If the monitored analog value has a reference value (refer to Appendix C:
Reference Values on page 310), the threshold is expressed as a percentage of this
reference value (-320.00 % to 320.00 %). If an analog input is monitored, the
threshold refers to the display value format (refer to Appendix C: Display Value
Format on page 317 for more information).
Refer to Table 3-53 for examples of how to configure the limit.
Example value
01.24 Total generator real power
01.09 Generator frequency
00.01 Engine speed
(configured to VDO 5 bar)
(configured to VDO 150C)
06.03. Analog input 3
(configured to Linear,
Value at 0% = 0,
Value at 100% = 1000)
Desired limit
160 kW
51.5 Hz
1256 rpm
4.25 bar
Reference value / display value

Generator rated real power (parameter 1752) = 200 kW
Rated frequency (parameter 1750) = 50 Hz
Rated speed (parameter 1601) = 1500 rpm
Display in 0.01 bar
Limit entry format

8000 (= 80.00 %)
10300 (= 103.00 %)
06373 (= 63.73 %)
00425 (= 4.25 bar)
123 C
Display in C
00123 (= 123C)
10 mm
Display in 0.000 m
(parameter 1035 on page 165 configured to 0.000m)
00010 (= 0.010
mm)
DE
EN
Table 3-53: Monitoring - flexible limits - analog value examples
CL2
{0}
{1o}
DE
EN
4216
CL2
{0}
{1o}
DE
EN
4207
CL2
4201
{0}
{1o}
Hysteresis
Hysterese
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
FlexLimit {x} [x = 1 to 16]: Hysteresis
0 to 32000
During monitoring, the actual value must exceed or fall below one of the limits
defined in parameter 4205 to be recognized as out of permissible limits. For a value
to register as having returned to the permissible limits, the monitored value must
rise above or fall below this value for the hysteresis. The format for entering the
hysteresis depends on the monitored analog input and corresponds with the one of
the threshold listed in parameter 4205.
FlexLimit {x} [x = 1 to 16]: Delay
00.02 to 327.00 s
If the monitored value exceeds or falls below the threshold value for the delay time
configured here, an alarm will be issued. If the monitored value falls below the
threshold (plus/minus the hysteresis, dependent on parameter 4204) before the
FlexLimit {x} [x = 1 to 16]: Alarm class
Class A/B/C/D/E/F/Control

Page 122/339
Woodward
Manual 37427
EN
Self acknowledge
Selbstquittierend
DE
CL2
4202
{0}
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
4203
FlexLimit {x} [x = 1 to 16]: Self acknowledge
Yes / No
no longer detected.
and reset by manually pressing the appropriate buttons, by
energizing the appropriate discrete input or via interface.
FlexLimit {x} [x = 1 to 16]: Engine speed delay
Yes / No
Table 3-54 shows a complete list of the parameter IDs for the flexible limits 1 through 16.
Flexible
limit #
Description
Monitoring
Monitored
analog input
Monitoring
at
Limit
Hysteresis
Delay
Alarm
class
Self
acknowledge
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4208
4225
4242
4259
7108
7116
7124
7132
7140
7148
7156
7164
7172
7180
7188
7196
4200
4217
4234
4251
4270
4280
4290
6000
6010
6020
6030
6040
6050
6060
6070
6080
4206
4223
4240
4257
4276
4286
4296
6006
6016
6026
6036
6046
6056
6066
6076
6086
4204
4221
4238
4255
4274
4284
4294
6004
6014
6024
6034
6044
6054
6064
6074
6084
4205
4222
4239
4256
4275
4285
4295
6005
6015
6025
6035
6045
6055
6065
6075
6085
4216
4233
4250
4267
4278
4288
4298
6008
6018
6028
6038
6048
6058
6068
6078
6088
4207
4224
4241
4258
4277
4287
4297
6007
6017
6027
6037
6047
6057
6067
6077
6087
4201
4218
4235
4252
4271
4281
4291
6001
6011
6021
6031
6041
6051
6061
6071
6081
4202
4219
4236
4253
4272
4282
4292
6002
6012
6022
6032
6042
6052
6062
6072
6082
Delayed
by engine
speed
4203
4220
4237
4254
4273
4283
4293
6003
6013
6022
6033
6043
6053
6062
6073
6083
Table 3-54: Monitoring - flexible limits - parameter IDs
Woodward
Page 123/339
Manual 37427
Configure Monitoring: Miscellaneous
DE
EN
Configure Monitoring: Miscellaneous, Alarm Acknowledgement
CL0
{0}
{1o}
DE
EN
1756
Time until horn reset

Zeit Hupenreset
CL2
12490
{0}
{1oc}
{2oc}
Ext. acknowledge
Ext. Quittierung
{1o}
{1oc}
{2oc}
Self acknowledgment of the centralized alarm (horn)
0 to 1,000 s
After each alarm of alarm class B through F occurs, the alarm LED flashes and the
horn (command variable 03.05) is enabled. After the delay time 'time until horn
reset' has expired, the flashing LED changes into a steady light and the horn
(command variable 03.05) is disabled. The alarm LED flashes until the alarm has
been acknowledged either via the push button, the LogicsManager, or the interface.
Note: If this parameter is configured to 0, the horn will remain active until it will be
acknowledged.
Protection: External acknowledgment of alarms
LogicsManager
It is possible to acknowledge all alarms simultaneously from remote, e.g. with a

discrete input. The logical output of the LogicsManager has to become TRUE
twice. The first time is for acknowledging the horn, the second for all alarm
messages. The On-delay time is the minimum time the input signals have to be "1".
The Off-delay time is the time how long the input conditions have to be "0" before
the next high signal is accepted. Once the conditions of the LogicsManager have
been fulfilled the alarms will be acknowledged.
The first high signal into the discrete input acknowledges the command
variable 03.05 (horn). The second high signal acknowledges all inactive
alarm messages.
The LogicsManager and its default settings are explained on page 271 in Appendix
B: "LogicsManager".
Page 124/339
Woodward
Manual 37427
Configure Monitoring: Miscellaneous, Configure CAN bus overload

The CAN busses are monitored. If the sum of CAN bus messages on all CAN buses together exceeds 32 per
20 ms, an alarm will be initiated.
If this protective function is triggered, the display indicates "CAN bus overload" and the logical command
Parameter table
Level
Text
CANopen interface 1 monitoring
Monitoring
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
0.01 to 650.00 s
A/B/C/D/E/F
Yes / No
On
5.00 s
B
No
DE
EN
Table 3-55: Monitoring - standard values - CAN bus overload
CL2
{0}
{1o}
DE
EN
3145
CL2
{0}
{1o}
DE
EN
3148
CL2
3146
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
CAN bus overload: Monitoring
On / Off
On ................ CAN bus overload monitoring is carried out according to the

CAN bus overload: Delay
0.01 to 650.00 s
If more than 32 CAN bus messages per 20 ms are sent on the CAN bus within this
time, the action specified by the alarm class is initiated.
CAN bus overload: Alarm class
DE
EN
CL2
3147
{0}
Woodward
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
CAN bus overload: Self acknowledgment
Yes / No
longer detected.
Page 125/339
Manual 37427
Configure Monitoring: Miscellaneous, Configure CAN Interface 1

The CANopen interface 1 is monitored. If the interface does not receive a Receive Process Data Object (RPDO)
before the delay expires, an alarm will be initiated.
If this protective function is triggered, the display indicates "CANopen interface 1" and the logical
Parameter table
Level
Text
Monitoring
Delay
Alarm class
Self acknowledgment
Delayed by eng. speed
Setting range
Default value
On / Off
0.01 to 650.00 s
A/B/C/D/E/F
Yes / No
Yes / No
Off
0.20 s
B
Yes
No
DE
EN
Table 3-56: Monitoring - standard values - CANopen interface 1
CL2
{0}
{1o}
DE
EN
3150
CL2
{0}
{1o}
DE
EN
3154
CL2
3151
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
CANopen Interface 1: Monitoring
On / Off
On .................CANopen interface 1 monitoring is carried out according to the

CANopen Interface 1: Delay
0.01 to 650.00 s
The maximum receiving break is configured with this parameter. If the interface
does not receive an RPDO within this time, the action specified by the alarm class
is initiated. The delay timer is re-initialized after every message is received.
CANopen Interface 1: Alarm class
DE
EN
CL2
3152
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3153
Page 126/339
CANopen Interface 1: Self acknowledgment
Yes / No
longer detected.
CANopen Interface 1: Engine delayed
Yes / No

Woodward
Manual 37427
Configure Monitoring: Miscellaneous, Configure CAN Interface 2

The CANopen interface 2 is monitored. If the interface does not receive a message from the external expansion
board (Node-ID) before the delay expires, an alarm will be initiated.
If this protective function is triggered, the display indicates "CANopen interface 2" and the logical
Parameter table
Level
Text
Monitoring
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
0.01 to 650.00 s
A/B/C/D/E/F
Yes / No
Yes / No
Off
0.20 s
B
Yes
No
DE
EN
Table 3-57: Monitoring - standard values - CANopen interface 2
CL2
{0}
{1o}
DE
EN
16187
CL2
{0}
{1o}
DE
EN
16186
CL2
16188
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
CANopen Interface 2: Monitoring
On / Off
On ................ CANopen interface 1 monitoring is carried out according to the

CANopen Interface 2: Delay
0.01 to 650.00 s
The maximum receiving break is configured with this parameter. If the interface
does not receive message from the external expansion board (Node-ID) within this
time, the action specified by the alarm class is initiated. The delay timer is reinitialized after every message is received.
CANopen Interface 2: Alarm class
DE
EN
CL2
16190
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
16189
CANopen Interface 2: Self acknowledgment
Yes / No
longer detected.
CANopen Interface 2: Engine delayed
Yes / No
NOTE
If you are not using the exact amount of external I/O modules you have defined, the monitoring
function does not work correct.
Woodward
Page 127/339
Manual 37427
Configure Monitoring: Miscellaneous, Configure CAN Interface 2, J1939 Interface

This watchdog triggers if the easYgen is configured to receive J1939 data from an ECU (parameter 15102)
connected to the CAN bus to evaluate these data, and no data is received from the ECU.
If this protective function is triggered, the display indicates "CAN fault J1939" and the logical command
Parameter table
Level
Text
J1939 interface monitoring
Monitoring
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
2 to 6500 s
A/B/C/D/E/F
Yes / No
Yes / No
Off
10 s
B
Yes
No
DE
EN
Table 3-58: Monitoring - standard values - J1939 interface
CL2
{0}
{1o}
DE
EN
15110
CL2
{0}
{1o}
DE
EN
15114
CL2
15111
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
J1939 Interface: Monitoring
On / Off
On .................Monitoring of the J1939 interface is carried out according to the

J1939 Interface: Delay
2 to 6500 s
The delay is configured with this parameter. If the interface does not receive a
CAN SAE J1939 protocol message before the delay expires, the action specified
by the alarm class is initiated. The delay timer is re-initialized after every message
is received.
J1939 Interface: Alarm class
Class A/B/C/D/E/F
DE
EN
CL2
15112
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
15113
Page 128/339
J1939 Interface: Self acknowledgment
Yes / No
no longer detected.
J1939 Interface: Engine delayed
Yes / No

Woodward
Manual 37427
Configure Monitoring: J1939 Interface, Configure CAN Interface 2, Red Stop Alarm
This watchdogs monitors, whether a specific alarm bit is received from the CAN J1939 interface. This enables to
configure the easYgen in a way that a reaction is caused by this bit (e.g. warning, shutdown).
If this protective function is triggered, the display indicates "Red stop lamp" and the logical command
Parameter table
Level
Text
J1939 interface red stop lamp monitoring
Monitoring
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
0 to 999 s
A/B/C/D/E/F
Yes / No
Yes / No
Off
2s
A
Yes
No
DE
EN
Table 3-59: Monitoring - standard values - J1939 interface red stop lamp
CL2
{0}
{1o}
DE
EN
15115
CL2
{0}
{1o}
DE
EN
15119
CL2
15116
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
J1939 Interface: Red stop lamp DM1: Monitoring
On / Off
On ................ Monitoring of the Red Stop Lamp message from the ECU is carried
out according to the following parameters.
Off................ Monitoring is disabled.
J1939 Interface: Red stop lamp DM1: Delay
0 to 999 s
The red stop lamp delay is configured with this parameter. If the ECU sends the
Red Stop Lamp On message, the action specified by the alarm class is initiated
after the delay configured here expires.
J1939 Interface: Red stop lamp DM1: Alarm class
DE
EN
CL2
15117
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
15118
Woodward
J1939 Interface: Red stop lamp DM1: Self acknowledgment
Yes / No
no longer detected.
J1939 Interface: Red stop lamp DM1: Engine delayed
Yes / No
Page 129/339
Manual 37427
Configure Monitoring: J1939 Interface, Configure CAN Interface 2, Amber Warning Alarm
This watchdogs monitors, whether a specific alarm bit is received from the CAN J1939 interface. This enables to
configure the easYgen in a way that a reaction is caused by this bit (e.g. warning, shutdown).
If this protective function is triggered, the display indicates "Amber warning lamp" and the logical
Parameter table
Level
Text
J1939 interface amber warning lamp monitoring
Monitoring
Delay
Alarm class
Self acknowledgment
Setting range
Default value
On / Off
0 to 999 s
A/B/C/D/E/F
Yes / No
Yes / No
Off
2s
A
Yes
No
DE
EN
Table 3-60: Monitoring - standard values - J1939 interface amber warning lamp
CL2
{0}
{1o}
DE
EN
15120
CL2
{0}
{1o}
DE
EN
15124
CL2
15121
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
J1939 Interface: Amber warning lamp DM1: Monitoring
On / Off
On .................Monitoring of the Amber Warning Lamp message from the ECU is

carried out according to the following parameters.
J1939 Interface: Amber warning lamp DM1: Delay
0 to 999 s
The amber warning lamp delay is configured with this parameter. If the ECU
sends the Amber Warning Lamp On message, the action specified by the alarm
class is initiated after the delay configured here expires.
J1939 Interface: Amber warning lamp DM1: Alarm class Class A/B/C/D/E/F/Control
DE
EN
CL2
15122
{0}
Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
15123
Page 130/339
J1939 Interface: Amber warning lamp DM1: Self acknowledgment
Yes / No
no longer detected.
J1939 Interface: Amber warning lamp DM1: Engine delayed
Yes / No

Woodward
Manual 37427
Configure Monitoring: Miscellaneous, Battery, Overvoltage (Levels 1 & 2)

There are two battery overvoltage alarm levels available in the control. Both alarms are definite time alarms and
are illustrated in the figure below. The figure diagrams a frequency trend and the associated pickup times and
length of the alarms. Monitoring of the voltage is done in two steps.
If this protective function is triggered, the display indicates "Bat. overvoltage 1" or
"Bat. overvoltage 2" and the logical command variable "08.01" or "08.02" will be enabled.
Parameter table
Level
Text
Setting range
Battery overvoltage (the hysteresis is 0,7 % of the rated value.)
Level 1
Monitoring
On / Off
Limit
8.0 to 42.0 V
Delay
0.02 to 99.99 s
Alarm class
A/B/C/D/E/F/Control
Self acknowledgment
Yes / No
Yes / No
Level 2
Monitoring
On / Off
Limit
8.0 to 42.0 V
Delay
0.02 to 99.99 s
Alarm class
A/B/C/D/E/F/Control
Self acknowledgment
Yes / No
Yes / No

thresholds.
Default value
On
32.0 V
5.00 s
B
No
No
Off
35.0 V
1.00 s
B
No
No
DE
EN
Table 3-61: Monitoring - standard values - battery overvoltage
CL2
{0}
{1o}
DE
EN
3450
3456
CL2
{0}
{1o}
DE
EN
3454
3460
CL2
{0}
{1o}
DE
EN
3455
3461
CL2
3451
3457
{0}
Woodward
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Battery overvoltage: Monitoring (Level 1/Level 2)
On / Off
On ................ Overvoltage monitoring of the battery voltage is carried out

according to the following parameters. Both values may be configured independent from each other (prerequisite: Level 1
> Level 2).
Battery overvoltage: Threshold value (Level 1/Level 2)
8.0 to 42.0 V
battery voltage reaches or exceeds this value for at least the delay time without
Battery overvoltage: Delay time (Level 1/Level 2)
0.02 to 99.99 s
If the monitored battery voltage exceeds the threshold value for the delay time
configured here, an alarm will be issued. If the monitored battery voltage falls
be reset.
Battery overvoltage: Alarm class (Level 1/Level 2)

Page 131/339
DE
EN
Manual 37427
CL2
3452
3458
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3453
3459
Page 132/339
Battery overvoltage: Self acknowledgment (Level 1/Level 2)
Yes / No
Yes................ The control automatically clears the alarm if the fault condition is
no longer detected.
Battery overvoltage: Engine delayed monitoring (Level 1/Level 2)
Yes / No
Yes................ Monitoring for fault conditions is not performed until engine

Woodward
Manual 37427
Configure Monitoring: Miscellaneous, Battery, Undervoltage (Levels 1 & 2)

There are two battery undervoltage alarm levels available in the control. Both alarms are definite time alarms and
are illustrated in the figure below. The figure diagrams a frequency trend and the associated pickup times and
length of the alarms. Monitoring of the voltage is done in two steps.
If this protective function is triggered, the display indicates "Bat. undervoltage 1" or
"Bat. undervoltage 2" and the logical command variable "08.03" or "08.04" will be enabled.
Parameter table
Level
Text
Setting range
Battery undervoltage (the hysteresis is 0,7 % of the rated value).
Level 1
Monitoring
On / Off
Limit
8.0 to 42.0 V
Delay
0.02 to 99.99 s
Alarm class
A/B/C/D/E/F/Control
Self acknowledgment
Yes / No
Yes / No
Level 2
Monitoring
On / Off
Limit
8.0 to 42.0 V
Delay
0.02 to 99.99 s
Alarm class
A/B/C/D/E/F/Control
Self acknowledgment
Yes / No
Yes / No

thresholds.
Default value
On
24.0 V
60.00 s
B
No
No
On
20.0 V
10.00 s
B
No
No
DE
EN
Table 3-62: Monitoring - standard values - battery undervoltage
CL2
{0}
{1o}
DE
EN
3500
3506
CL2
3504
3510
{0}
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Limit
Grenzwert
{1oc}
{2oc}
Battery undervoltage: Monitoring (Level 1/Level 2)
On / Off
On ................ Undervoltage monitoring of the battery voltage is carried out

according to the following parameters. Both values may be configured independent from each other (prerequisite: Level 1
> Level 2).
Battery undervoltage: Threshold value (Level 1/Level 2)
8.0 to 42.0 V
battery voltage reaches or falls below this value for at least the delay time without
DE
EN
Note
The default monitoring limit for battery undervoltage is 24 Vdc after 60 seconds.
This is because in normal operation the terminal voltage is approximately 26 Vdc
(alternator charged battery).
CL2
{0}
{1o}
DE
EN
3505
3511
CL2
3501
3507
{0}
Woodward
{1o}
Delay
Verzgerung
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Battery undervoltage: Delay time (Level 1/Level 2)
0.02 to 99.99 s
If the battery voltage falls below the threshold value for the delay time configured
here, an alarm will be issued. If the battery voltage exceeds the threshold (plus the
hysteresis) again before the delay expires the time will be reset.
Battery undervoltage: Alarm class (Level 1/Level 2)

Page 133/339
DE
EN
Manual 37427
CL2
3502
3508
{0}

Self acknowledge
Selbstquittierend
{1o}
{1oc}
{2oc}
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
3503
3509
Page 134/339
Battery undervoltage: Self acknowledgment (Level 1/Level 2)
Yes / No
no longer detected.
Battery undervoltage: Engine delayed monitoring (Level 1/Level 2)
Yes / No

Woodward
Manual 37427
Configure Monitoring: Miscellaneous, Multi-Unit Parameter Alignment

The multi-unit parameter alignment functionality requires that the relevant parameters are all configured
identically at all participating units.
If at least one of these parameters is configured different in at least one of the units, the display indicates
"Parameter alignment" on all units and the logical command variable "08.16" will be enabled.
This alarm is always self-acknowledging, i.e. the control automatically clears the alarm if it is no longer valid.
Figure 3-14: Monitoring - miscellaneous parameter alignment
Participating unit is different configured

Participating unit is identical configured
The setting of the following parameters will be monitored:
Start stop mode (parameter 5752 on page 196)

Fit size of engine (parameter 5754 on page 197)
Fit service hours (parameter 5755 on page 198)
Changes of engines (parameter 5756 on page 199)
IOP Reserve power (parameter 5760 on page 201)
IOP Hysteresis (parameter 5761 on page 201)
IOP Max. generator load (parameter 5762 on page 201)
IOP Min. generator load (parameter 5763 on page 202)
IOP Dynamic (parameter 5757 on page 203)
IOP Add on delay (parameter 5764 on page 204)
IOP Add on delay at rated load (parameter 5765 on page 204)
IOP Add off delay (parameter 5766 on page 204)
MOP Minimum load (parameter 5767 on page 205)
MOP Reserve power (parameter 5768 on page 205)
MOP Hysteresis (parameter 5769 on page 205)
MOP Max. generator load (parameter 5770 on page 206)
MOP Min. generator load (parameter 5771 on page 206)
MOP Dynamic (parameter 5758 on page 207)
MOP Add on delay (parameter 5772 on page 208)
MOP Add on delay at rated load (parameter 5773 on page 208)
MOP Add off delay (parameter 5774 on page 208)
Transfer rate LS fast message (parameter 9921 on page 260)
Parameter table
Level
Text
Multi-unit parameter alignement monitoring
Monitoring
Alarm class
Setting range
Default value
On / Off
A/B/C/D/E/F
On
B
DE
EN
Table 3-63: Monitoring - standard values - multi-unit parameter alignment monitoring
CL2
4070
{0}
Woodward
{1o}
Monitoring
berwachung
{1oc}
{2oc}
Multi-unit parameter alignment: Enable
On / Off
On ................ Multi-unit parameter alignment monitoring is carried out.

Page 135/339
DE
EN
Manual 37427
CL2
4071
{0}
{1o}
Alarm class
Alarmklasse
{1oc}
{2oc}
Multi-unit configuration check: Alarm class
Class A/B/C/D/E/F

This function may be assigned an independent alarm class that specifies what
action should be taken when this function triggers an alarm.
Page 136/339
Woodward
Manual 37427
Configure Monitoring: Miscellaneous, Multi-Unit Missing Members

The multi-unit missing members monitoring function checks whether all participating units are available (sending
data on the load share line).
If the number of available units is less than the number of members configured in parameter 4063 for at least the
delay time (refer to below note), the display indicates "Missing members" and the logical command variable
"08.17" will be enabled.
NOTE
After energizing the easYgen, a delay is started, which allows a possible "Missing members" alarm to
become active. This delay depends on the Node-ID of the easYgen (parameter 8950 on page 246) and
the transfer rate of a load share fast message (parameter 9921 on page 260) and may last for approx.
140 seconds for a high Node-ID (e.g. 127). This delay serves for detecting the Master of a CAN bus
connection. Approximately two minutes after energizing the easYgen, the alarm delay will be set to a
fix time, which depends on the setting of parameter 9921 on page 260 (Transfer rate LS fast message)
and is in the range between 3 to 12 seconds.
Parameter table
Level
Text
Multi-unit missing members monitoring
Monitoring
Number of gens communicating
Alarm class
Self acknowledge
Setting range
Default value
On / Off
0 to 32
A/B/C/D/E/F
Yes / No
Off
2
B
No
DE
EN
Table 3-64: Monitoring - standard values - multi-unit missing members monitoring
CL2
DE
EN
4060
CL2
{1o}
{0}
{1o}
DE
CL2
4061
{1oc}
{2oc}
Number of gens communicating

Anzahl Teilnehmer
EN
4063
{0}
Monitoring
berwachung
{0}
{1o}
{1oc}
{2oc}
Alarm class
Alarmklasse
{1oc}
{2oc}
Multi-unit missing members monitoring: Enable
On / Off
On ................ Multi-unit missing members monitoring is carried out.

Multi-unit missing members monitoring: Number of participants
0 to 64
The number of units participating in load sharing is configured here.

Multi-unit missing members monitoring: Alarm class
Class A/B/C/D/E/F

This function may be assigned an independent alarm class that specifies what
action should be taken when this function triggers an alarm.
DE
EN
Self acknowledge
Selbstquittierend
CL2
4062
{0}
Woodward
{1o}
{1oc}
{2oc}
Multi-unit missing members monitoring: Self acknowledgment
Yes / No
no longer detected.
Page 137/339
Manual 37427
Configure Application
Configure Application: Configure Breakers

NOTE
The assignment of the defined relays to defined functions occurs by selection of the application mode
(i.e. function "Command: Close GCB" on relay [R 6], this relay can no longer be operated via the
LogicsManager). The same way some relays are designated to specific functions, others may be
assigned to different functions. These are listed as "programmed" relays. If a relay is "programmable"
the function may be assigned to other relays via the LogicsManager by configuration. Refer to Table
3-78 on page 170 for more information.
NOTE
If the easYgen is intended to be operated in parallel with the mains, the mains voltage measuring
inputs must be connected. If an external mains decoupling is performed, jumpers between busbar and
mains voltage measuring inputs may be installed.
NOTE
Changing the application mode will not change other configured values in the parameters. The
application mode parameter is the only one.
Parameter table
Level
Text
Configure breakers
Application mode
Breaker transition mode
Breaker transition mode 1
Transition mode 1
Transfer time GCBMCB
Dead bus detection max. volt.
Setting range
Default value
GCB/MCB / GCB / GCB open /

None
Parallel / Interchange /
Closed Transit. /
Open Tranistion / External
Parallel / Interchange /
Closed Transit. /
Open Tranistion / External
LogicsManager
1.00 to 99.99 s
0 to 30 %
GCB/MCB
Parallel
Parallel
(0 & 1) & 1
1.00 s
10 %
Table 3-65: Application - standard values - configure breakers
Page 138/339
Woodward
DE
EN
Manual 37427
CL2
3401
{0}
Application mode
Betriebsmodus
{1o}
{1oc}
{2oc}
Application modes
"None" / "GCB open" / "GCB" / "GCB/MCB"
The unit may be configured for four different application modes. The discrete
inputs and relay outputs are pre-defined dependent upon the selected application
mode. Only the screens and functions that pertain to the application mode selected
are displayed. The single line diagram in the main screen will change. Refer to the
Operation manual 37428 for additional information.
None ............. Application mode {0} "Engine Control" [start/stop]
The control unit will function as an engine start/stop control with
generator and engine protection. All necessary inputs and outputs are
assigned and pre-defined.
GCB open .... Application mode {1o} "Protection" [open GCB]
The control unit will function as an engine start/stop control with
generator and engine protection. The control unit can only open the
GCB. All necessary inputs and outputs are assigned and pre-defined.
GCB ............. Application mode {1oc} "1-CB control" [open/close GCB]
The control unit will function as a 1 CB unit. The control unit
performs full control like synchronizing, opening and closing the
GCB with generator and engine protection. All necessary inputs and
outputs are assigned and pre-defined.
GCB/MCB... Application mode {2oc} "2 CB control" [open/close GCB/MCB]
The control unit will function as a 2 CB unit. The control unit
performs full control like synchronizing, opening and closing the
GCB and the MCB with generator and engine protection. The
GCB/MCB perform also full load transfer via open/closed transition,
interchange and parallel mode. All necessary inputs and outputs are
assigned and pre-defined.
Woodward
Page 139/339
Manual 37427
Operation Of The Circuit Breakers

The configuration of pulse switching takes place in the following screen and has the described effect on the signal
sequence (the MCB cannot be controlled by the continuous pulse for security reasons, because otherwise, the
MCB would be opened in case of a failure/exchange of the easYgen). The parameter "Enable MCB"
allows/prevents the closing of the MCB. A closed MCB will not be opened. If the parameter "Auto unlock" is
configured to YES, an open pulse will be issued prior to each close pulse.
Dead bus closing GCB {1oc} or {2oc}
The unit closes the GCB, if the following conditions are met. The display indicates "GCB dead bus cls".
Automatic operation
The operating mode AUTOMATIC has been selected
No class C alarm or higher is present
The engine is running
The engine delayed monitoring (parameter 3315on page 184) as well as the generator stable time
(parameter 3415 on page 151) have been expired or the LogicsManager function "Undelay close GCB"
(parameter 12210 on page 151) is enabled
The generator voltage and frequency are within the configured operating range (refer to Configure
Monitoring: Generator, Operating Voltage / Frequency on page 48)
The MCB has been opened for at least the time configured in "Transfer time GCBMCB"
(parameter 3400 on page 148) ({2oc} with open transition mode only)
The busbar voltage is below the dead bus detection limit (parameter 5820 on page 148)
Manual operation
The operating mode MANUAL has been selected.
No class C alarm or higher is present
The engine is running
The engine delayed monitoring (parameter 3315on page 184) as well as the generator stable time
(parameter 3415 on page 151) have been expired
The generator voltage and frequency are within the configured operating range (refer to Configure
Monitoring: Generator, Operating Voltage / Frequency on page 48)
The button "Close GCB" has been pressed
The MCB has been open for at least the time configured in "Transfer time GCBMCB" (parameter 3400
on page 148) ({2oc} with open transition mode only)
Page 140/339
Woodward
Manual 37427
Synchronization GCB/MCB {1oc} or {2oc}

The synchronization is active, if the following conditions are met simultaneously. The display indicates
"Synchronization GCB" or "Synchronization MCB".
Automatic operation
The mains voltage is available and within the configured operating range (refer to Configure Monitoring:
Mains, Operating Voltage / Frequency on page 83)
The generator and busbar voltage are available and within the configured operating range (refer to
Configure Monitoring: Generator, Operating Voltage / Frequency on page 48)
The differential frequency/voltage is within the configured operating range
Synchronizing the MCB
The GCB is closed (or at least one GCB is closed in a multiple genset application)
The busbar voltage is within the configured operating range
The "Enable MCB" (parameter 12923 on page 155) signal is present, for example discrete input 6 is
energized if configured as DI 6
Synchronizing the GCB
The MCB is closed
Engine delayed monitoring (parameter 3315 on page 184) and generator stable time (parameter 3415
on page 151) have expired or "Undelay close GCB" (parameter 12210 on page 151) is enabled
Manual operation
Operating mode MANUAL has been selected
The generator and busbar voltage is available and within the configured operating range (refer to
Configure Monitoring: Generator, Operating Voltage / Frequency on page 48)
The differential frequency/voltage is within the configured operating range
Synchronizing the MCB
The GCB is closed (or at least one GCB is closed in a multiple genset application)
The button "Close MCB" has been pressed
Synchronizing the GCB
The MCB is closed
Engine delayed monitoring (parameter 3315 on page 184) and generator stable time (parameter 3415
on page 151) have expired or "Undelay close GCB" (parameter 12210 on page 151) is enabled
The button "Close GCB" has been pressed
Dead bus start MCB {2oc}
The unit closes the MCB, if the following conditions are met simultaneously. The display indicates "MCB dead
bus cls".
Automatic operation
The parameter "Dead busbar closure MCB" (parameter 3431 on page 154) is configured On
The GCB is open or has been opened for at least the "Transfer time GCBMCB" (parameter 3400 on
page 148) (open transition mode only)
Woodward
Page 141/339
Manual 37427
Manual operation
Operating mode MANUAL has been selected
The parameter "Dead busbar closure MCB" (parameter 3431 on page 154) is configured On
The GCB is open or has been opened for at least the "Transfer time GCBMCB" (parameter 3400 on
page 148) (open transition mode only)
energized if configured so
The button "Close MCB" has been pressed
Open GCB {1o} or {1oc} or {2oc}
The GCB will be opened when the "Command GCB open" is issued. The behavior of the GCB open relay
depends on the setting of parameter 3403 on page 149. If this parameter is configured as "N.O.", the relay
energizes to open the GCB, if it is configured as "N.C.", the relay de-energizes to open the GCB. The GCB will
be opened under the following conditions.
In STOP operating mode after unloading the generator
In case of a class C alarm or higher
By pressing the "GCB" or "MCB" softkey (depending on the CB logic which has been set) in MANUAL
operating mode
By pressing the button "stop engine" in MANUAL operating mode
In the event of an automatic stopping in the AUTOMATIC operating mode (the start request has been
terminated or a stop request has been initiated)
By pressing the "MCB" softkey (depending on the CB logic which has been set) in MANUAL operating
mode
Above conditions are only valid if the GCB is closed, whereas the following conditions are valid regardless of the
GCB is open or closed.
Prior to the MCB closing onto the dead busbar (depending on the CB logic which has been set)
In case of an alarm of class D or F
Open MCB {2oc}
The MCB will be opened when the relay "Command: MCB open" is energized. The MCB will be opened under
the following conditions if the MCB is closed.
If an emergency power operation is initiated (mains failure) once the generator voltage is within the
permissible limits
Prior to the closure of the GCB (depending on the CB logic which has been set)
Upon pressing the "MCB" or "GCB" softkey (dependent upon the configured CB logic) in MANUAL
operating mode
Page 142/339
Woodward
Manual 37427
DE
EN
Transition Mode
CL2
3411
Breaker transition mode

Schaltermodus
{0}
{1o}
---
---
{1oc}
---
{2oc}
Breaker: Transition mode
Parallel / Interchange / Closed T. / Open T. / External
The control unit automatically controls the two breakers (MCB and GCB). Up to
five (5) breaker logic modes may be selected. These are:
{1oc}
--PARALLEL
-------
{2oc}
EXTERNAL
PARALLEL
OPEN TRANSITION
CLOSED TRANSITION
INTERCHANGE
A detailed explanation for each mode may be found in the following text.
DE
EN
Alternative Transition Modes

The unit provides two alternative transition modes, which may be activated temporarily via the LogicsManager
and override the transition mode configured in parameter 3411.
CL2
3412
Breaker transition mode 1

Schaltermodus Alternative 1
{0}
{1o}
---
---
{1oc}
---
{2oc}
Breaker: Transition mode 1
Parallel / Interchange / Closed T. / Open T. / External
The control unit automatically controls the two breakers (MCB and GCB). Up to
five (5) breaker logic modes may be selected. These are:
{1oc}
--PARALLEL
-------
{2oc}
EXTERNAL
PARALLEL
OPEN TRANSITION
CLOSED TRANSITION
INTERCHANGE
DE
EN
A detailed explanation for each mode may be found in the following text.
CL2
12931
{0}
Transition mode 1
LS-Modus Alternat. 1
---
Woodward
{1o}
---
{1oc}
---
{2oc}
Breaker: Transition mode 1
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the transition mode
configured in parameter 3412 will be used instead of the standard transition mode
configured in parameter 3411. The LogicsManager and its default settings are
explained on page 271 in Appendix B: "LogicsManager".
Page 143/339
Manual 37427
Breaker Logic "PARALLEL"

Parallel operation is enabled by configuring parameter 3411 to "PARALLEL".
NOTE
Parallel breaker logic must be selected for the following operation modes:
Isolated operation
Mains parallel operation
In the event of an engine start request the following occurs:

The GCB is synchronized and closed
The generator assumes load and the adjusted real power or reactive power set points are controlled
Following the stop request the following occurs:
The generator sheds load until real power has reached the "Unload limit" (parameter 3125)
The generator power factor is controlled to "1.00" (unity)
The GCB is opened
The engine is shut down following the configured cool down period
NOTE
When a stop command is issued to the engine, soft loading (power reduction) is carried out before
opening the GCB, except an alarm of class D or F is present.
Page 144/339
Woodward
Manual 37427
Breaker Logic "INTERCHANGE" {2oc}

Mains interchange (import/export) real power control is enabled by configuring parameter 3411 to
"INTERCHANGE".
NOTE
For this breaker logic to function correctly, the mains power measurement must be connected
properly. The following applies for the power display:
Positive mains power
= export power
Negative mains power = import power
In the event of a start request, a change is made from mains to generator supply. The following occurs:
The generator assumes load until the imported mains interchange real power has reached 3 % of the
"Generator rated active power" (parameter 1752)
The MCB is opened
When a stop request has been issued, a change is made from generator to mains supply. The following occurs:
The MCB is synchronized and closed
The generator sheds load until real power has reached the "Unload limit" (parameter 3125)
The generator power factor is controlled to "1.00" (unity)
The GCB is opened
Breaker Logic "CLOSED TRANSIT." {2oc}
Closed transition (make-before-break/overlap synchronization) is enabled by configuring parameter 3411 to
"CLOSED TRANSITION".
NOTE
The circuit breakers are opened irrespective of the power.
In the event of an engine start request, a change is made from mains to generator supply. The following occurs:
The MCB is opened and the generator assumes all loads
After the engine stop request has been issued, a change is made from generator to mains supply. The following
occurs:
The MCB is synchronized and closed
The GCB is opened and the mains assume all loads
NOTE
The maximum time between the reply from the CB and the CB open command is 500 ms.
Woodward
Page 145/339
Manual 37427
Breaker Logic "OPEN TRANSIT." {2oc}

Open transition (break-before-make/change over logic) is enabled via configuration of parameter 3411 to "OPEN
TRANSITION".
In the event of an engine start request, a change is made from mains to generator supply. The following occurs:
The MCB is opened
The GCB is closed after the time configured in "Transfer time GCB<->MCB" (parameter 3400 on page 148)
has expired
After the engine stop request has been issued, a change is made from generator to mains supply. The following
occurs:
The GCB is opened
The MCB is closed after the time configured in "Transfer time GCB<->MCB" parameter 3400 on page 148
has expired
Breaker Logic "EXTERNAL"
External breaker logic is enabled via configuration of parameter 3411 to "EXTERNAL".
All breaker control (especially the CB closing instructions) must be carried out via master controller (e.g. a PLC).
The easYgen controller always issues additionally the breaker open command under fault conditions and in the
breaker unloading states (Unloading GCB) if the stop request is active.
Page 146/339
Woodward
Manual 37427
Overview {2oc}
STOP
MANUAL
AUTOMATIC
EXTERNAL: Breaker logic "External"

In a mains parallel operation, decoupling from the mains is carried out via the MCB or the GCB in the event of a mains
failure. The breakers will not automatically close in emergency power operation. Emergency power operation in accordance
with European Community Specification DIN VDE 0108 is not possible in this power circuit breaker logic.
The GCB is opened.
The MCB and the GCB may be
The GCB is opened if the genset is
manually opened. The circuit breakers
stopped or if decoupling from the mains,
but will not close if the engine is started.
are opened for decoupling from the
The MCB is opened only if decoupling
mains.
from the mains, and is never closed.
PARALLEL: Breaker logic "Mains parallel operation"
The MCB and GCB are synchronized to permit continuous mains parallel operation in this breaker logic mode.
The GCB is opened; the MCB is
Mains parallel operation can be initiated The GCB is synchronized via an add-on
operated depending on the setting of
by pressing the "GCB On" or "MCB
request and a mains parallel operation is
"Enable MCB" (parameter 12923).
On" push-button.
performed. When a shed-off request is
issued, the generator sheds load and
opens the GCB and the engine is shut
down following the configured cool
down period.
Emergency power: The emergency
power operation is terminated following
the expiration of the mains settling time.
The MCB is synchronized and closed,
putting the system back into a mains
parallel operation.
OPEN TRANSIT.: Breaker logic "Open transition / change-over / brake-before-make"
The MCB and GCB are never synchronized in this breaker logic mode.
A change can be made to either
A change is made to generator operation
generator or mains operation by pressing through an add-on request. Once the
either the "GCB On" or "MCB On"
add-on request is terminated, the system
push-button. The "STOP" push-button
changes back to mains operation. The
opens the GCB and simultaneously
MCB is closed when the busbar is dead,
stops the engine.
even if there has not been an add-on
request. Emergency power operations
are terminated following the expiration
of the mains settling timer. The GCB
opens and the MCB closes, transferring
all loads to the mains.
CLOSED TRANSIT.: Breaker logic "Closed transition / make-before-brake / overlap synchronization"
The MCB and the GCB are synchronized, in order to avoid a dead busbar in this breaker logic mode. Immediately after the
synchronization of one breaker, the other is opened. Continuous mains parallel operation is not possible.
Synchronization of either the generator The GCB is synchronized via an add-on
or the mains can be initiated by pressing request. After the GCB closes the MCB
the "GCB On" or "MCB On" pushis opened. Following the shed-off
button.
request being issued, the MCB is
synchronized and closed. After the
MCB has closed the GCB is opened.
the expiration of the mains settling time
and the MCB synchronizing to the
generator. The MCB closes and the
GCB opens immediately afterwards.
Woodward
Page 147/339
Manual 37427
Overview {2oc} (continued)

STOP
MANUAL
AUTOMATIC
INTERCHANGE: Breaker logic "Soft loading / interchange synchronization"

The MCB and the GCB are synchronized, in order to avoid a dead busbar in this breaker logic mode. The operation of a
breaker under load is avoided by utilizing the ability to soft load. Continuous mains parallel operation is not possible with this
breaker logic. Following the shed-off request, the MCB synchronizes and closes, the generator soft unloads to the mains and
the GCB opens. After the GCB is open the engine is stopped following the expiration of the configured cool down period.
Synchronization of either the generator Via an engine request, the GCB is
or the mains can be initiated by pressing synchronized and the generator power is
the "GCB On" or "MCB On" pushincreased. The MCB is then opened.
button.
Following the disabling of the engine
request, the MCB is reverse
synchronized and the GCB is then
opened.
the expiration of the mains settling time.
The MCB closes, the load is transferred,
and the GCB opens.
Overview {1oc}
STOP
MANUAL
AUTOMATIC
DE
EN
PARALLEL: Breaker logic "Mains parallel"

This operation mode may be used both in the case of an isolated system, an isolated parallel system, and a system that is
operated in mains parallel.
The GCB is opened.
Mains parallel operation can be
The GCB is synchronized via an add-on
performed via the "GCB On" pushrequest and mains parallel operation is
button.
performed. When a shed-off request is
issued, the generator sheds load, the
GCB is opened, and the engine is shut
down following the configured cool
down period.
CL2
3400
Transfer time GCBMCB

Pausenzeit GLSNLS
{0}
---
{1o}
---
{1oc}
---
{2oc}
Breaker: Transfer time GCB MCB
0.10 to 99.99 s
Switching from generator supply to mains supply or from mains supply to

generator supply occurs automatically if the operating conditions have been met.
The time between the reply "power circuit breaker is open" and a close pulse is
set by this parameter. This time applies for both directions. During this time the
consumers are de-energized.
Note: This is only valid, if parameter 3411 on page 143 is configured to OPEN
TRANSITION
Configure Application: Configure Breakers, Dead Bus Detection Limit
DE
EN
Dead bus detection max. volt.

Max. Spannung fr SamS schwarz
{1o}
{1oc}
{2oc}
CL2 {0}
5820
Page 148/339
Operating values, maximum voltage for dead bus detection
0 to 30 %
If the busbar voltage falls below this percentage of the busbar 1 rated voltage
(parameter 1781 on page 38), a dead bus condition is detected and the logical
command variable 02.21 (Busbar 1 is dead) becomes TRUE.
Woodward
Manual 37427
Configure Application: Configure Breakers, GCB
NOTE
Normally Open Contacts (No): If a voltage is applied to the discrete input terminals, the discrete input
is enabled (i.e. in the operating state). The controller only recognizes a fault condition or control
operation via the discrete input when the discrete input terminals are energized. If fault monitoring
is performed via Normally Open contacts, the state of the system should be monitored by the state
of the discrete input.
Normally Closed Contacts (NC): If a voltage is applied to the discrete input terminals, the discrete input
is not enabled (i.e. in the idle state). The controller only recognizes a fault condition or control
operation via the discrete input when the discrete input terminals are de-energized.
Normally Open Contacts
current flow
RELEASE
RELEASE
Relay operates
Normally Closed Contacts

24 V
Operating current
contact
Idle-current
contact
Idle-current
contact
RELEASE
no current flow
24 V
0V
Operating current
contact
RELEASE
Relay releases
0V
Figure 3-15: Normally Open / Normally Closed contacts
Parameter table
Level
Text
Configure GCB
GCB open relay
GCB close command
GCB time pulse
Synchronmization GCB
Voltage differential GCB
Pos. freq. differential GCB
Neg. freq. differential GCB
Max. positive phase angle GCB
Max. negative phase angle GCB
Phase matching GCB dwell time
Dead bus closure
Generator stable time
Closing time GCB
Undelay close GCB
Setting range
Default value
N.O. / N.C. / Not used

Constant / Impulse
0.10 to 0.50 s
Slip frequency / Phase matching
0.50 to 20.00 %
0.02 to 0.49 Hz
-0.49 to 0.00 Hz
0.0 to 60.0
-60.0 to 0.0
0.0 to 60.0 s
On / Off
0 to 99 s
40 to 300 ms
LogicsManager
N.O.
Constant
0.50 s
Slip frequency
5.00 %
+0.18 Hz
-0.10 Hz
7.0
-7.0
3.0 s
On
2s
80 ms
(04.09 & 1) & 1
DE
EN
Table 3-66: Application - standard values - configure GCB
CL2
3403
{0}
GCB open relay

GLS ffnen-Kontakt
---
Woodward
{1o}
{1oc}
{2oc}
Breaker: "Command: GCB open" relay
N.O. / N.C. / Not used
N.O. (normally open) ... The relay "command: GCB open" will be energized to
open the GCB and will be de-energized again after the discrete input
"Reply GCB" is energized to signal the control that the GCB is open.
N.C. (normally closed) . The relay "command: GCB open" will be de-energized to
open the GCB and will be energized again after the discrete input
"Reply GCB" is energized to signal the control that the GCB is open.
Not used ....... A GCB open relay is not used and relay R7 (Command: open GCB)
is freely programmable. In this case, parameter 3414 must be
configured to "Constant" to open the breaker.
Page 149/339
DE
EN
Manual 37427
CL2
3414
{0}
---
GCB close command

GLS Schlieen-Befehl
{1o}
---
{1oc}
{2oc}
Breaker: "Command: GCB close"
Constant / Impulse
Impulse ........The relay "Command: GCB close" issues an add-on pulse. If the
relay is configured in this manner a holding coil and sealing contacts
must be installed externally to the control unit. The DI "Reply GCB"
is used to identify closed contacts.
Constant.......The relay "Command: close GCB" may be wired directly into the
holding circuit for the power circuit breaker. If this method is utilized
it is recommended that isolation relays are used. After the connect
pulse has been issued and the reply of the power circuit breaker has
been received, the relay "Command: close GCB" remains energized.
If a class C alarm or higher occurs or a GCB open command is
issued, this relay de-energizes.
DE
EN
In both cases the relay "Command: GCB open" energizes to open the GCB if
parameter 3403 is not configured as "Not used".
CL2
DE
EN
3416
CL2
DE
EN
5729
CL2
5700
{0}
---
GCB time pulse

GLS Impulsdauer
{1o}
{1oc}
{2oc}
Synchronization GCB
Synchronisierung GLS
{0}
---
{1o}
---
{1oc}
---
{2oc}
Voltage differential GCB

Max. Spg. Differenz GLS
{0}
---
{1o}
---
{1oc}
{2oc}
Breaker: Pulse duration to close the GCB
0.10 to 0.50 s
The time of the pulse output may be adjusted to the breaker being utilized.
Breaker: Synchronization frequency GCB
Slip frequency .... The frequency controller adjusts the frequency in a way, that the
frequency of the source (generator) is marginal greater than the target
(busbar). When the synchronizing conditions are reached, a close
command will be issued. The slipping frequency depends on the
setting of "Slip frequency offset" (parameter 5502 on page 221).
Phase matching .. The frequency controller adjusts the phase angle of the source
(generator) to that of the target (busbar), in view of turning the phase
difference to zero.
Breaker: Voltage differential GCB
0.50 to 20.00 %
This value refers to the generator rated voltage (parameter 1766 on

page 38).
DE
EN
The maximum permissible voltage differential for closing the generator circuit
breaker is configured here.
If the difference between generator and busbar voltage does not exceed the value
configured here and the generator voltage is within the operating voltage window
(parameters 5800/5801 on page 48), the "Command: GCB close" may be issued.
CL2
DE
EN
5701
CL2
5702
Pos. freq. differential GCB

Max. positiver Schlupf GLS
{0}
---
{1o}
---
{1oc}
{2oc}
Neg. freq. differential GCB

Max. negativer Schlupf GLS
{0}
---
{1o}
---
Page 150/339
{1oc}
{2oc}
Breaker: Positive frequency differential GCB
0.02 to 0.49 Hz
The prerequisite for a close command being issued for the GCB is that the
differential frequency is below the configured differential frequency. This value
specifies the upper frequency (positive value corresponds to positive slip
generator frequency is higher than the busbar frequency).
Breaker: Negative frequency differential GCB
-0.49 to 0.00 Hz
differential frequency is above the configured differential frequency. This value
specifies the lower frequency limit (negative value corresponds to negative slip
generator frequency is less than the busbar frequency).
Woodward
Manual 37427
DE
EN
Max positive phase angle GCB

Max. pos. Winkeldifferenz GLS
{1o}
{1oc} {2oc}
CL2 {0}
----5703
Breaker: Max. permissible positive phase angle GCB
0.0 to 60.0
This parameter is only displayed, if parameter 5729 is configured to

"Phase matching".
The prerequisite for a close command being issued for the GCB is that the leading
phase angle between generator and busbar is below the configured maximum
permissible angle.
DE
EN
Max negative phase angle GCB

Max. neg. Winkeldifferenz GLS
{1o}
{1oc} {2oc}
CL2 {0}
----5704
Breaker: Max. permissible negative phase angle GCB
-60.0 to 0.0

"Phase matching".
lagging phase angle between generator and busbar is above the configured
minimum permissible angle.
DE
EN
Phase matching GCB dwell time

Verweildauer GLS
{1o}
{1oc} {2oc}
CL2 {0}
----5707
Breaker: Phase matching dwell time of GCB
0.0 to 60.0 s

"Phase matching".
DE
EN
This is the minimum time that the generator voltage, frequency, and phase angle
must be within the configured limits before the breaker will be closed.
CL2
DE
EN
3432
CL2
{0}
{1o}
---
{0}
---
DE
CL2
12210
{1oc}
{2oc}
{1oc}
{2oc}
Closing time GCB

Schaltereigenzeit GLS
EN
5705
---
Generator stable time

Wartezeit vor GLS schlieen
DE
CL2
{1o}
---
EN
3415
{0}
Dead bus closure GCB

Schwarz schlieen GLS
{0}
---
Woodward
{1o}
---
{1oc}
{2oc}
Undelay close GCB

GLS unverzgert
{1o}
---
{1oc}
{2oc}
Breaker: Dead busbar closure GCB
On / Off
On .................A dead busbar closure is allowed if the required conditions are met.
Off ................A GCB close command to a dead busbar is prevented. A
synchronization is still possible.
Breaker: "Command: GCB close": Breaker delay
0 to 99 s
The time configured here begins to count down once the engine monitoring delay
timer has expired. This permits for an additional delay time before the breaker is
closed in order to ensure that none of the engine delayed watchdogs trips. It is
possible to bypass this delay time through the LogicsManager (parameter 12210
on page 151) in the event an emergency operation condition (mains failure)
occurs.
Unnecessary CB switching operations and voltage interruptions should be avoided
by utilizing this parameter.
Inherent delay of GCB for synchronization
40 to 300 ms
The inherent closing time of the GCB corresponds to the lead-time of the close
command. The close command will be issued independent of the differential
frequency at the entered time before the synchronous point.
Breaker: Undelay closing of the GCB
LogicsManager
Once the conditions of the LogicsManager have been fulfilled the GCB will be
closed immediately (without waiting for engine speed delay and generator stable
timer to expire). When using the standard setting, the GCB will be closed without
delay in emergency power operation. The LogicsManager and its default settings
are explained on page 271 in Appendix B: "LogicsManager".
Page 151/339
DE
EN
Manual 37427
CL2
DE
EN
3405
CL2
5708
{0}
---
GCB auto unlock

GLS auto entriegeln
{1o}
---
{1oc}
{2oc}
GCB open time pulse

GLS ffnen Impulsdauer
{0}
---
{1o}
Page 152/339
---
{1oc}
{2oc}
Breaker: Breaker unblocking GCB
Yes / No
This is used for special circuit breakers to put the breaker into a defined initial
state or to enable closing at all.
YES .............. Before every close-pulse, an open-pulse is issued for 1 second. A
CB close pulse is enabled only after the open pulse is issued.
NO ................ The CB close pulse is enabled without being preceded by a CB
open pulse.
Breaker: GCB open time pulse
0.10 to 9.90 s
This time defines the length of the GCB open time pulse, if the automatic switch
unblocking GCB is activated.
Woodward
Manual 37427
Configure Application: Configure Breakers, MCB

Parameter table
Level
Text
Configure MCB
MCB control (easYgen-2200)
MCB control (easYgen-2500)
MCB time pulse
Synchronmization MCB
Voltage differential MCB
Pos. freq. differential MCB
Neg. freq. differential MCB
Max. positive phase angle MCB
Max. negative phase angle MCB
Phase matching MCB dwell time
Dead bus closure
Enable MCB
Setting range
Default value
Off / 1 Relay
Off / 1 Relay / 2 Relays
0.10 to 0.50 s
0.50 to 20.00 %
0.02 to 0.49 Hz
-0.49 to 0.00 Hz
0.0 to 60.0
-60.0 to 0.0
0.0 to 60.0 s
On / Off
LogicsManager
1 Relay
2 Relays
0.50 s
Slip frequency
5.00 %
+0.18 Hz
-0.10 Hz
7.0
-7.0
3.0 s
On
(09.06 & !08.07) &
!07.05
80 ms
Closing time MCB
40 to 300 ms
Table 3-67: Application - standard values - configure MCB

DE
EN
MCB control
NLS Ansteuerung
CL2
{0}
{1o}
---
---
DE
CL2
5733
{1oc}
---
{2oc}
MCB control
NLS Ansteuerung
EN
5732
{0}
{1o}
---
---
{1oc}
---
{2oc}
Breaker: MCB control (easYgen-2200)
Off / 1 Relay
Off ................A MCB is not operated. Relay R5 (38/39/40) can be freely used.
1 Relay .........A MCB is operated and if necessary monitored. Relay R5
(38/39/40) is used and fixed to this function.
Breaker: MCB control (easYgen-2500)
Off / 1 Relay / 2 Relays
Off ................A MCB is not operated. Relay R5 (38/39/40) can be freely used.
1 Relay .........A MCB is operated and if necessary monitored. Relay R5
(38/39/40) is used and fixed to this function.
2 Relays ........A MCB is operated and if necessary monitored. Relay R5
(38/39/40) is used for the open function, relay R8 (82/83) to close
it. The opening and closing is carried out with the pulse method.
NOTE
Even if the MCB operation (Parameter 5732/5733) is switched off and the breaker application mode is
configured to GCB/MCB, the reply of the MCB is observed anyway.
DE
EN
MCB time pulse

NLS Impulsdauer
CL2
{0}
DE
CL2
5730
{1o}
---
EN
3417
{0}
---
{1oc}
---
{2oc}
Synchronization MCB
Synchronisierung NLS
---
Woodward
{1o}
---
{1oc}
---
{2oc}
Breaker: Pulse duration to close the MCB
0.10 to 0.50 s
The time of the pulse output may be adjusted to the breaker being utilized.
Breaker: Synchronization frequency MCB
Slip frequency The frequency controller adjusts the frequency in a way, that the
frequency of the source (busbar) is marginal greater than the target
(mains). When the synchronizing conditions are reached, a close
command will be issued. The slipping frequency is positive to avoid
reverse power.
Phase matching The frequency controller adjusts the phase angle of the source
(busbar) to that of the target (mains), in view of turning the phase
difference to zero.
Page 153/339
DE
EN
Manual 37427
CL2
5710
Voltage differential MCB

Max. Spg. Differenz NLS
{0}
---
{1o}
---
{1oc}
---
{2oc}
Breaker: Voltage differential MCB
0.50 to 20.00 %
This value refers to the mains rated voltage (parameter 1768 on page 38).
DE
EN
The maximum permissible voltage differential for closing the mains circuit
breaker is configured here.
If the difference between mains and busbar voltage does not exceed the value
configured here and the mains voltage is within the operating voltage window
(parameters 5810/5811 on page 84), the "Command: MCB close" may be issued.
CL2
DE
EN
5711
CL2
DE
EN
5712
CL2
5713
Pos. freq. differential MCB

Max. positiver Schlupf NLS
{0}
---
{1o}
---
{1oc}
---
{2oc}
Neg. freq. differential MCB

Max. negativer Schlupf NLS
{0}
---
{1o}
---
{1oc}
---
{2oc}
Max positive phase angle MCB

Max. positive Winkeldiff. NLS
{0}
{1o}
---
---
{1oc}
---
{2oc}
Breaker: Positive frequency differential MCB
0.02 to 0.49 Hz
The prerequisite for a connect command being issued for the MCB is that the
differential frequency is below the configured differential frequency. This value
specifies the upper frequency (positive value corresponds to positive slip
busbar frequency is higher than the mains frequency).
Breaker: Negative frequency differential MCB
-0.49 to 0.00 Hz
differential frequency is above the configured differential frequency. This value
specifies the lower frequency limit (negative value corresponds to negative slip
busbar frequency is less than the mains frequency).
Breaker: Max. permissible positive phase angle MCB
0.0 to 60.0

"Phase matching".
DE
EN
leading phase angle between busbar and mains is below the configured
maximum permissible angle.
CL2
5714
Max negative phase angle MCB

Max. negative Winkeldiff. NLS
{0}
{1o}
---
---
{1oc}
---
{2oc}
Breaker: Max. permissible negative phase angle MCB
-60.0 to 0.0

"Phase matching".
lagging phase angle between busbar and mains is above the configured minimum
permissible angle.
DE
EN
Phase matching MCB dwell time

Verweildauer NLS
{1o}
{1oc}
{2oc}
CL2 {0}
------5717
Breaker: Phase matching dwell time of MCB
0.0 to 60.0 s

"Phase matching".
DE
EN
This is the minimum time that the generator/busbar voltage, frequency, and
phase angle must be within the configured limits before the breaker will be
closed.
CL2
3431
{0}
Dead bus closure MCB

Schwarz schlieen MCB
---
Page 154/339
{1o}
---
{1oc}
---
{2oc}
Breaker: Dead busbar closure MCB
On / Off
On ................ A dead busbar closure is allowed if the required conditions are

met.
Off ............... An MCB close command to a dead busbar is prevented. A
synchronization is still possible.
Woodward
DE
EN
Manual 37427
CL2
{0}
---
DE
EN
12923
CL2
{0}
---
DE
EN
5715
CL2
DE
EN
3407
CL2
5718
{0}
---
{1o}
Enable MCB
Freigabe NLS
{1oc}
---
---
{2oc}
Closing time MCB

Schaltereigenzeit NLS
{1o}
{1oc}
---
---
{2oc}
---
{1oc}
---
{1o}
---
{1oc}
Breaker: Synchronization: Inherent delay of MCB for synchronization 40 to 300 ms
The inherent closing time of the MCB corresponds to the lead-time of the close
command. The close command will be issued independent of the differential
frequency at the entered time before the synchronous point.
Yes / No
This is used for special circuit breakers to put the breaker into a defined initial
state or to enable closing at all.
YES .............. Before every close-pulse, an open-pulse is issued for 1 second. A
CB close pulse is enabled only after the open pulse is issued.
NO ............... The CB close pulse is enabled without being preceded by a CB
open pulse.
{2oc}
Breaker: MCB open time pulse
MCB open time pulse

NLS ffnen Impulsdauer
{0}
Once the conditions of the LogicsManager have been fulfilled the MCB will be
enabled. The LogicsManager and its default settings are explained on page 271
in Appendix B: "LogicsManager".
DI 6 is pre-assigned by default to this function, but may be configured freely.
Breaker: Switch unblocking MCB
MCB auto unlock

NLS auto entriegeln
{1o}
LogicsManager
Breaker: Enable MCB
0.10 to 9.90 s
This time defines the length of the MCB open time pulse, if the automatic switch
unblocking MCB is activated.
{2oc}
Configure Application: Configure Breakers, Synchronization

Parameter table
Level
Text
Configure synchronization
Synchronization mode
Setting range
Default value
Off / Permissice / Check / Run
RUN
DE
EN
Table 3-68: Application - standard values - configure synchronization
CL2
5728
{0}
---
Woodward
Synchronization mode
Synchronisiermodus
{1o}
---
{1oc}
---
{2oc}
Breaker: Synchronization mode Off / Permissive / Check / Run / Controlled by LM
Off ............... The synchronization is disabled; the frequency and voltage

adaptation for synchronization is not active.
Permissive ... The unit acts as a synch check device. The unit will not issue
speed or voltage bias commands to achieve a synchronization, but
if synchronization conditions are matched (frequency, phase,
voltage and phase angle), the control will issue a breaker close
command. There are two different functionalities of this option
depending on the setting of parameter 3414 on page 150 (GCB
close command):
GCB close command set to Impulse
The GCB close command is pulsed as long as the synchronization
conditions are matched.
GCB close command set to Constant
The GCB close command remains enabled as long as the
synchronization conditions are matched.
Check .......... Used for checking a synchronizer prior to commissioning. The
control actively synchronizes generator(s) by issuing speed and
voltage bias commands, but does not issue a breaker closure
command.
Run .............. Normal operating mode. The control actively synchronizes and
issues breaker closure commands.
Page 155/339
Manual 37427
Configure Application: Configure Inputs and Outputs

Configure Analog Inputs (FlexIn)
Parameter table
Level
Text
Configure analog inputs
Display temperature in
Display pressure in
Setting range
Default value
C / F
bar / psi
C
bar
Table 3-69: Application - standard values - configure analog inputs
DE
EN
Display temperature in
Temperaturanzeige in
CL1
{0}
{1o}
DE
CL1
3630
{1oc}
{2oc}
Display pressure in
Druckanzeige in
EN
3631
{0}
{1o}
{1oc}
{2oc}
Temperature display in
C / F
C....................... The temperature is displayed in C (Celsius).

F ....................... The temperature is displayed in F (Fahrenheit).
Pressure display in
bar / psi
bar ..................... The pressure is displayed in Bar.

psi ...................... The pressure is displayed in psi.
NOTE
Refer to the Application Manual 37429 for a detailed configuration example of an analog input.
Analog Inputs: Characteristics "Table A" And "Table B" (9 Point Scaling)
The characteristic curves of "Table A" and "Table B" (freely configurable over 9 defined percentage points) are
independently configurable for all analog inputs. Each percentage point may be scaled to related values measured
from the analog input (0 to 500 Ohm or 0 to 20 mA), so that the actual display reflects the measured values (i.e.
200 to 600 kW). The so developed characteristic curve can be used for visualization and monitoring via the
configuration to "Table A" (for Table A) as well as "Table B" (for Table B).
Range:
{x1}
0
{x2}
10
{x3}
25
{x4}
40
{x5}
50
{x6}
60
{x7}
75
{x8}
90
A = 60
0 kW
20.0 m
{y1}
580 kW
200 kW
18.0 m
A=
{y2}
= 540 kW
250 kW
15.0 m
A
{y3}
465 kW
{y4}
300 kW
12.0 m
A=
350 kW
10.0 m
A = 380
{y5}
330 kW
{y6}
400 kW
8.0 mA
=
450 kW
5.0 mA
= 260 kW
{y7}
= 225 kW
{y8}
500 kW
2.0 mA
550 kW
= 200 kW
{y9}
0.0 mA
600 kW
kW
[corresponds] Value
Input
{x9}
100
[%]
[mA]
0 to 20 mA
0.0
2.0
5.0
8.0
10.0
12.0
15.0
18.0
20.0
0 to 500 Ohm
0.0
50.0
125.0
200.0
250.0
300.0
375.0
450.0
500.0 [Ohm]
Figure 3-16: Analog input scaling - table (example)
Page 156/339
Woodward
Manual 37427
NOTE
The X and Y junction may be moved within the range of values (the junctions don't have to be
equidistant).
When configuring the X coordinates, ensure the coordinates always increase in scale continuously. In
the following example the first set of x/y coordinates are correct and the second set of x/y coordinates
are wrong:
correct
X-coord. 0 %
Y-coordinate -100
10 %
-95
20 %
-500
40 %
-10
50 %
+3
60 %
+17
80 %
+18
90 %
+100
100 %
+2000
wrong
X-coord. 0 %
10 %
20 %
60 %
20 %
30 %
80 %
40 % 100 %
Y-coordinate -100
-50
-95
+18
+17
+3
-10
+2000 +100
If the first X coordinate is >0%, all values smaller than the first X value will be output with the first
Y value. If the last Y value is <100%, all higher values will be output with the value of Y9.
Parameter table
Level
Text
Configure user defined table A / B
Table A
X-value 1
Y-value 1
X-value 2
Y-value 2
X-value 3
Y-value 3
X-value 4
Y-value 4
X-value 5
Y-value 5
X-value 6
Y-value 6
X-value 7
Y-value 7
X-value 8
Y-value 8
X-value 9
Y-value 9
Table B
X-value 1
Y-value 1
X-value 2
Y-value 2
X-value 3
Y-value 3
X-value 4
Y-value 4
X-value 5
Y-value 5
X-value 6
Y-value 6
X-value 7
Y-value 7
X-value 8
Y-value 8
X-value 9
Y-value 9
Setting range
Default value
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
0 to 100 %
-32000 to 32000
2%
0
8%
207
16 %
512
24 %
838
27 %
970
31 %
1160
36 %
1409
37 %
1461
41 %
1600
4%
2553
6%
2288
8%
2100
13 %
1802
16 %
1685
23 %
1488
28 %
1382
42 %
1188
58 %
1035
Table 3-70: Application - standard values - configure analog input table A / B
Woodward
Page 157/339
Manual 37427
DE
EN
The following parameters are used to configure the characteristic curve. Refer to Table 3-71 for the parameter
IDs of the individual parameters for all scaling points of tables A and B.
CL2
{0}
{1o}
DE
EN
3560
CL2
3550
{0}
{1o}
X-value {a}
X-Wert {a}
{1oc}
{2oc}
Y-value {b}
Y-Wert {b}
{1oc}
{2oc}
Table {x} [x = A/B]: X-coordinate {a} [a = 1 to 9]
0 to 100 %
The analog input is assigned to a curve. This parameter defines the actual
percentage assigned to each of the nine points along the X-axis of the total range of
the selected hardware for analog input. For example: If a 0 to 20 mA input is
configured and the X1-coordinate = 0%, then the value configured for Y1 is output
for an input of 0 mA.
Table {x} [x = A/B]: Y-coordinate {b} [b = 1 to 9]
-9999 to 9999
This parameter defines the Y-coordinate (the displayed and monitored value) at the
corresponding X-coordinate. For example: If a 0 to 20mA input is configured and
the X2-coordinate = 10%, then the value configured for the Y2-coordinate is output
for an input of 2 mA.
Table 3-71 shows a complete list of the parameter IDs for the table scaling points.
Scaling point No.
Table A - X value
Table A - Y value
Table B - X value
Table B - Y value
1
3560
3550
3610
3600
2
3561
3551
3611
3601
3
3562
3552
3612
3602
4
3563
3553
3613
3603
5
3564
3554
3614
3604
6
3565
3555
3615
3605
7
3566
3556
3616
3606
8
3567
3557
3617
3607
9
3568
3558
3618
3608
Table 3-71: Analog inputs - table characteristics - parameter IDs
Page 158/339
Woodward
Manual 37427
Analog Inputs: Inputs 1 to 3
NOTE
Monitoring of the analog inputs (overrun/underrun) must be configured manually to the flexible limits
(refer to Configure Monitoring: Flexible Limits on page 120).
Parameter table
Level
Text
Configure analog inputs 1 to 3
Description
Type
User defined min display value

User defined max display value
Sender value at display min.
Sender value at display max.
Sender type
Offset
Sender connection type
Monitoring wire break
Wire break alarm class
Self acknowledge wire break
Filter time constant
Bargraph minimum
Bargraph maximum
Value format
Setting range
Default value
1 to 16 character text
Off / VDO 5bar / VDO 10bar /
VDO 150C / VDO 120C /
Pt100 / Linear /
Table A / Table B
-32000 to 32000
-32000 to 32000
0.00 to 100.00 %
0.00 to 100.00 %
0 - 500 Ohm / 0 20 mA
-20.0 to 20.0 Ohm
Two wire / One wire
Off / High / Low / High/Low
A / B / C / D / E / F / Control
Yes / No
Off / 1 / 2 / 3 / 4 / 5
-32000 to 32000
-32000 to 32000
Analog inp. {x}

Off
0
1000
0.00 %
100.00 %
0 - 500 Ohm
0.0 Ohm
Two wire
Off
B
No
3
0
1000
000000
DE
EN
Table 3-72: Application - standard values - configure analog inputs 1 to 3
CL2
T
{0}
1025
1075
1125
{1o}
Description
Beschreibung
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Message text
user-defined
The event history will store this text message and it is also displayed on the
visualization screen. If the programmed limit value of the analog input has been
reached or exceeded this text is displayed in the control unit screen. The text may
have 1 through 16 characters.
Note: This parameter may only be configured using ToolKit.
Woodward
Page 159/339
DE
EN
Manual 37427
CL2
1000
1050
1100
{0}
{1o}
{1oc}
Type
Typ
{2oc}
Analog input {x} [x = 1 to 3]: Type

Off / VDO 5bar / VDO 10bar /
VDO 150C / VDO 120C / Pt100 / Linear / Table A / Table B
The characteristic curves of the inputs can be found in Appendix F

(page 327).
According to the following parameters different measuring ranges are possible at
the analog inputs. The selectable ranges are:
Off ..................... The analog input is switched off.
VDO 5bar ......... The value of the analog input is interpreted with the VDO
characteristics 0 to 5 bar.
VDO 10bar ....... The value of the analog input is interpreted with the VDO
characteristics 0 to 10 bar.
VDO 150C ....... The value of the analog input is interpreted with the VDO
characteristics 50 to 150 C.
VDO 120C ....... The value of the analog input is interpreted with the VDO
characteristics 40 to 120 C.
Pt100 ................. The value of the analog input is interpreted with a Pt100
characteristic.
Linear................ Each analog input may be assigned to a linear characteristic
curve, which can be only used for the respective defined input
[T{x}] (x = 1 to 2). The minimum (0 %) and maximum (100 %)
value refers to the total measuring range of the analog input
(i.e. 0 to 500 Ohm or 0 to 20 mA) or the values configured as
"Sender value at display min." (parameter 1039, 1089, or 1139)
and "Sender value at display max." (parameter 1040, 1090, or
1140).
Table A / B ........ The analog input is assigned to a characteristic curve which is
defined over 9 points (stored in a table). Two independent tables
(table A and table B) may be allocated to the analog inputs. Note
that if these tables are to be used with the analog inputs, the
defined points of these tables must be programmed into the
control unit.
NOTE
The following parameters "User defined min display value" and "User defined max display value" are
only visible if the previous parameter "Type" is configured to "Linear".
Analog input {x} [x = 1 to 3]: User defined minimum display value
User defined max display value

Frei definierbare max Anzeige
CL2 {0} {1o} {1oc} {2oc}
Analog input {x} [x = 1 to 3]: User defined maximum display value
DE
EN
User defined min display value

Frei definierbare min Anzeige
CL2 {0} {1o} {1oc} {2oc}
DE
EN
1001
1051
1101
1002
1052
1102
Page 160/339
-32000 to 32000
The value to be displayed for the minimum of the input range must be entered
here.
-32000 to 32000
The value to be displayed for the maximum of the input range must be entered
here.
Woodward
Manual 37427
NOTE
DE
EN
The following parameters "Sender value at display min" and "Sender value at display max" are only
visible if the previous parameter "Type" is configured to "Linear", "Table A", or "Table B".
CL2
1039
1089
1139
Sender value at display min.

Quellwert bei min Anzeige
{0}
{1o}
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Source value at display minimum
0.00 to 100.00 %
The value of the configured input range, which shall correspond with the
minimum value configured for the display, must be entered here. This specifies the
lower limit of the hardware range to be measured.
DE
EN
Example: If the input range is 0 to 20 mA where 0 mA corresponds with 0 % and

20 mA corresponds with 100 %, and the value configured here is 20 %, an analog
input value of 4 mA would correspond with the minimum value configured for the
display.
CL2
1040
1090
1140
Sender value at display max.

Quellwert bei max Anzeige
{0}
{1o}
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Source value at display maximum
0.00 to 100.00 %
The value of the configured input range, which shall correspond with the
maximum value configured for the display, must be entered here. This specifies
the upper limit of the hardware range to be measured.
Example: If the input range is 0 to 500 Ohm where 0 Ohm corresponds with 0 %
and 500 Ohm corresponds with 100 %, and the value configured here is 36 %, an
analog input value of 180 Ohm would correspond with the maximum value
configured for the display.
NOTE
DE
EN
The following parameter "Sender type" must be configured to "0 to 500 Ohm", if "Type" (parameter
1000, 1050, or 1100) is configured to "VDO xx" or "Pt100".
CL2
1020
1070
1120
{0}
Sender type
Auswahl Hardware
Woodward
{1o}
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Hardware
0 to 500 Ohm / 0 to 20 mA
The software in the control unit may be configured for various types of sensors.
The configurable ranges apply to the linear analog input. Configurable ranges are:
0 to 500 Ohm The measuring range of the analog input is 0- to 500 Ohm.
0 Ohm = 0 %, 500 Ohm = 100 %.
0 to 20 mA ... The measuring range of the analog input is 0 to 20 mA.
0 mA = 0 %, 20 mA = 100 %.
Page 161/339
Manual 37427
NOTE
DE
EN
The following parameters "Offset" and "Sender connection type" are only visible if the previous
parameter "Sender type" is configured to "0 to 500 Ohm".
CL2
DE
EN
1046
1096
1146
CL2
1041
1091
1141
{0}
{1o}
{1oc}
Offset
Offset
{2oc}
Sender connection type

Anschlu Typ
{0}
{1o}
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Offset
-20.0 to 20.0 Ohm
The resistive input (the "0 to 500Ohm" analog input) may be calculated with a
permanent offset to adjust for inaccuracies. If the offset feature is utilized, the value
configured in this parameter will be added to/subtracted from the measured
resistive value. This has the following effect to the measured values (please note
tables starting on page 327):
-20.0 to 0.1 Ohm
VDO temperature: The displayed value will decrease.
VDO pressure: The displayed value will increase.
+0.1 to 20.0 Ohm
VDO temperature: The displayed value will increase.
VDO pressure: The displayed value will decrease.
Analog input {x} [x = 1 to 3]: Connection type
Two-pole / Single-pole
This parameter defines the type of the used sender. Refer to the Installation Manual
37426 for wiring details.
Two-pole ......A two-wire sender is connected to the easYgen. The unit measures
the sender values between the dedicated terminals.
Single-pole ...A one-wire sender is connected to the easYgen. The unit measures
the sender values between the terminal of the analog input and the
engine ground terminal.
The respective analog input is monitored for wire break.

If this protective function is triggered, the display indicates "Wb: {Text of Parameter
[Description]}" (parameter 1025/1075/1125 on page 159).
DE
EN
Monitoring wire break

Drahtbruchberw.
CL2
1003
1053
1103
{0}
{1o}
Page 162/339
{1oc}
{2oc}
Analog input {x} [x = 1 to 3] wire break monitoring
Off / High / Low / High/Low
The analog input can be monitored for a wire break. The following configurations
are used to monitor for a wire break:
Off ................No wire break monitoring is performed.
High ..............If the actual value rises over the maximum value (overshoot), this is
identified as a wire break.
Low...............If the actual value falls below the minimum value (undershoot), this
is identified as a wire break.
High/Low .....If the actual value rises over the maximum value (overshoot) or falls
below the minimum value (undershoot), this is identified as a wire
break.
Woodward
Manual 37427
NOTE
Monitoring of the analog inputs (overrun/underrun) must be configured manually to the flexible limits
(refer to Configure Monitoring: Flexible Limits on page 120).
If the control unit detects that the measuring range for an analog input has been exceeded and an
alarm is issued, the limit value monitoring of this analog input is disabled and an error message is
displayed.
The measuring range is recognized as being exceeded and an alarm is issued:
0 to 20 mA
Minimum value .........2 mA ................Undershooting
Maximum value.........20.5 mA ...........Overshooting
0 to 500 Ohm
Minimum value .........5 Ohm .............Undershooting (Offset = 0 Ohm)
Maximum value.........515 Ohm .........Overshooting (Offset = 0 Ohm)
Note: Depending on what was configured for the offset value (parameter 1046/1096/1146 on page 162)
the displayed value may be shifted. This may result in a broken wire being recognized early or later
than the actual value being measured. (An offset of +20ohms will recognize a wire break at 25ohms
instead of 5ohms.)
NOTE
A wire break is indicated in ToolKit by displaying an analog input value of 3276.6.
NOTE
DE
EN
The following two parameters are only visible, if wire break monitoring (parameter 1003/1053/1103 on
page 162) is not configured Off.
CL2
DE
EN
1004
1054
1104
CL2
1005
1055
1105
Wire break alarm class

Drahtbruch Alarmklasse
{0}
{1o}
{1oc}
{2oc}
Analog in. {x} [x = 1 to 3]: Alarm class wire break monit.

Self acknowledge wire break

Drahtbruch selbstquitt.
{0}
Woodward
{1o}
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Self acknowledged
Yes / No
longer detected.
Page 163/339
DE
EN
Manual 37427
CL2
10113
10114
10116
{0}

Filter
{1o}
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Filter time constant
Off / 1 / 2 / 3 / 4 / 5
A filter time constant may be used to reduce the fluctuation of an analog input
reading. This filter time constant assesses the average of the signal according to the
following formula:
Cut off frequency =
1
20ms 2 2 N 1
, whereby "N" is the parameter.
DE
EN
Off ................The analog input is displayed without filtering.

1 ....................Cut-off-frequency = 7.96 Hz (filter time constant = 0.02 s)
CL2
3632
3634
3636
{0}
Bargraph minimum
Bargraph Minimum
{1o}
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Bar graph minimum value
-9999 to 9999
The start value for the bar graph display of the analog input is defined here. The
value must be entered according to the display format, which refers to the analog
input type (parameter 1000 on page 160).
DE
EN
Note: This parameter is only effective if parameter 1000 is configured to Linear or

Table A/B.
CL2
3633
3635
3637
{0}
Bargraph maximum
Bargraph Maximum
{1o}
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Bar graph maximum value
-9999 to 9999
The end value for the bar graph display of the analog input is defined here. The
value must be entered according to the display format, which refers to the analog
input type (parameter 1000 on page 160).
Note: This parameter is only effective if parameter 1000 is configured to Linear or
Table A/B.
Page 164/339
Woodward
DE
EN
Manual 37427
CL2
T
{0}
1035
1085
1135
{1o}

Value format
Zahlenformat
{1oc}
{2oc}
Analog input {x} [x = 1 to 3]: Value format
user-defined
If a sign to denote a negative measured value (i.e. 10) is required, then the
first "0" of the numeric display is utilized for this symbol.
To display the measuring value of the analog input for the analog input types linear
as well as Table A and Table B (parameter 1000 on page 160) correctly this
parameter is to be used to define the format. The zeros in the numeric display are
used for the measuring values and are configurable. The placeholders for the digits
may have symbols (i.e. commas).
Note
This parameter may only be configured using ToolKit.
This parameter only applies to the linear and the user defined Table A and
Table B (parameter 1000 on page 160) analog input types.
The displayed value should be configured with the same number of digits as the
desired value to be measured.
The measured value will be displayed from right to left. If the measured value is
larger than the number of digits in the display, only a portion of the measured
value will be shown. An example of this would be a display of three digits is
configured when four digits will be needed. Instead of the number "1234" being
displayed only "234" will be shown.
Examples
Fuel level
- value at 0 % ..............0
- value at 100 % ..........1000
- desired display .........up to 1,000mm
- this parameter ...........0,000mm
Angle
- value at 0 % ..............-1799
- value at 100 % ..........1800
- desired display .........-179.9 to 180.0
- this parameter ...........0000.0
Pressure
- value at 0 % ..............0
- value at 100 % ..........100
- desired display .........up to 10.0bar
- this parameter ...........00.0bar
Note
If the analog input type (parameter 1000 on page 160) is configured to VDO or
Pt100, the following formats apply:
VDO 5 bar
display in 0.01 bar example: 5.0 bar > ToolKit display: 50,0
VDO 10 bar display in 0.01 bar example: 6.6 bar > ToolKit display: 66,0
VDO 120C display in C
example: 69C > ToolKit display: 6,9
VDO 150C display in C
Pt100
display in C
Woodward
Page 165/339
Manual 37427
Configure Discrete Inputs

Number
Terminal
{0}
Internal discrete inputs, board #1

[DI1]
44
[DI2]
45
[DI3]
46
[DI4]
47
[DI5]
48
[DI6]
49
[DI7]
50
[DI8]
51
[DI9]
76
[DI10]
77
Application mode
{1o}
{1oc}
{2oc}
Alarm input (LogicsManager); pre-configured for 'Emergency Stop'

Control input (LogicsManager); pre- configured for 'Start request in AUTO'
Alarm input (LogicsManager); pre- configured for 'Low oil pressure'
Alarm input (LogicsManager); pre- configured for 'Coolant temperature'
Control input (LogicsManager); pre- configured for 'External acknowledgement'
Control input (LogicsManager); pre- configured for 'Release MCB'
Reply MCB
Reply GCB
Alarm input (LogicsManager)
Alarm input (LogicsManager)
Table 3-73: Discrete inputs - terminal assignment
NOTE
Alarm inputs may also be configured as control inputs and then be used as command variables in the
LogicsManager.
Discrete inputs may be configured to normally open (N.O.) or normally closed (N.C.) states. In the state N.O., no
potential is present during normal operation; if an alarm is issued or control operation is performed, the input is
energized. In the state N.C., a potential is continuously present during normal operation; if an alarm is issued or
control operation is performed, the input is de-energized.
Vdc (GND)
GND (Vdc)
Discrete input (N.O.)
Vdc (GND)
GND (Vdc)
Discrete input (N.C.)

Figure 3-17: Discrete inputs - alarm/control inputs - operation logic
NOTE
All reply messages from breakers are evaluated as N.C.
Parameter table
Level
Text
Configure discrete inputs 1 to 10
Text
Operation
Delay
Alarm class
Self acknowledge
Setting range
Default value
N.O. / N.C.
0.08 to 650.00 s
Yes / No
Yes / No
see parameter list

N.O.
0.20 s
B
No
No
Table 3-74: Application - standard values - configure discrete inputs
NOTE
The DIs 1 to 5 are pre-configured to various functions and differ in their default values. However, they
may still be configured freely. The DIs 7 & 8 are always used for the circuit breaker replies and cannot
be configured.
Page 166/339
Woodward
DE
EN
Manual 37427
CL2
T
{0}
{1o}
DI {x} Text
DI {x} Text
{1oc}
{2oc}
1400
Discrete input: Message text
user-defined
If the discrete input is enabled with alarm class, this text is displayed on the
control unit screen. The event history will store this text message as well. The
text may have 4 through 16 characters.
Note: This parameter may only be configured using ToolKit.
Note: If the DI is used as control input with the alarm class "Control", you may
enter here its function (e.g. external acknowledgement) for a better overview
within the configuration.
DE
EN
DI {x} Operation
DI {x} Funktion
CL2
{0}
DE
EN
1201
CL2
{0}
DE
EN
1200
CL2
1202
{0}
{1o}
{1oc}
{2oc}
DI {x} Delay
DI {x} Verzgerung
{1o}
{1oc}
{2oc}
DI {x} Alarm class

DI {x} Alarmklasse
{1o}
{1oc}
{2oc}
Discrete input: Operation
N.O. / N.C.
The discrete inputs may be operated by an normally open (N.O.) or normally

closed (N.C.) contact. The idle circuit current input can be used to monitor for a
wire break. A positive or negative voltage polarity referred to the reference point
of the DI may be applied.
N.O. ............. The discrete input is analyzed as "enabled" by energizing the input
(normally open).
N.C............... The discrete input is analyzed as "enabled" by de-energizing the
input (normally closed).
Discrete input: Delay
0.08 to 650.00 s
A delay time in seconds can be assigned to each alarm or control input. The
discrete input must be enabled without interruption for the delay time before the
unit reacts. If the discrete input is used within the LogicsManager this delay is
taken into account as well.
Discrete input: Alarm class
see chapter "Alarm Classes" on page 269.

An alarm class may be assigned to the discrete input. The alarm class is executed
when the discrete input is enabled.
If "control" has been configured, there will be no entry in the event history and a
function out of the LogicsManager (description at page 270) can be assigned to
the discrete input.
DE
EN
DI {x} Delayed by engine speed

DI {x} Verzgert durch Motordr.
{1o}
{1oc} {2oc}
CL2 {0}
1203
Woodward
Discrete input: Engine delayed monitoring
Yes / No
Page 167/339
DE
EN
Manual 37427
CL2
1204
{0}
DI {x} Self acknowledge

DI {x} Selbstquittierend
{1o}
{1oc}
{2oc}
Discrete input: Self acknowledgment
Yes / No
no longer detected.
If the DI is configured with the alarm class "Control", self acknowledgement is
always active.
NOTE
If a discrete input has been configured with a shut-down alarm that has been enabled to selfacknowledge, and has been configured as engine delayed the following scenario may happen:
The discrete input shuts down the engine because of its alarm class.
Due to the engine stopping, all engine delayed alarms are ignored.
The alarm class is acknowledged automatically.
The alarm will self-acknowledge and clear the fault message that shut the engine down. This
prevents the fault from being analyzed. After a short delay, the engine will restart.
After the engine monitoring delay expires, the fault that originally shut down the engine will do so
again. This cycle will continue to repeat until corrected.
The preceding parameters are used to configure the discrete inputs 1 through 10. The parameter IDs refer to DI 1.
Refer to Table 3-75 for the parameter IDs of the parameters DI 2 through DI 10.
Text
Operation
Delay
Alarm class
Self acknowledged
DI 1
1400
1201
1200
1202
1203
1204
DI 2
1410
1221
1220
1222
1223
1224
DI 3
1420
1241
1240
1242
1243
1244
DI 4
1430
1261
1260
1262
1263
1264
DI 5
1440
1281
1280
1282
1283
1284
DI 6
1450
1301
1300
1302
1303
1304
DI 9
1480
1361
1360
1362
1363
1364
DI 10
1488
1381
1380
1382
1383
1384
Table 3-75: Discrete inputs - parameter IDs
NOTE
The DIs 7 & 8 are always used for the circuit breaker replies and cannot be configured.
Page 168/339
Woodward
Manual 37427
Configure External Discrete Inputs

If a Woodward IKD 1 or other external expansion board (Phoenix Contact) is connected to the easYgen via the
CAN bus, it is possible to use 16 additional discrete inputs.
The configuration of these external DIs is performed in a similar way like for the internal DIs. Refer to Table
3-77 for the parameter IDs of the parameters for external DIs 1 through 16.
Parameter table
Level
Text
Configure external discrete inputs 1 to 16 {x}
Text
Operation
Delay
Alarm class
Self acknowledge
Setting range
Default value
N.O. / N.C.
0.05 to 650.00 s
Yes / No
Yes / No
Ext. DI {x}
N.O.
0.20 s
Control
No
No
Table 3-76: Application - standard values - configure discrete inputs

External
Text
Operation
Delay
Alarm class
Self acknowledged
External
Text
Operation
Delay
Alarm class
Self acknowledged
DI 1
16200
16001
16000
16002
16003
16004
DI 9
16280
16081
16080
16082
16083
16084
DI 2
16210
16011
16010
16012
16013
16014
DI 10
16290
16091
16090
16092
16093
16094
DI 3
16220
16021
16020
16022
16023
16024
DI 11
16300
16101
16100
16102
16103
16104
DI 4
16230
16031
16030
16032
16033
16034
DI 12
16310
16111
16110
16112
16113
16114
DI 5
16240
16041
16040
16042
16043
16044
DI 13
16320
16121
16120
16122
16123
16124
DI 6
16250
16051
16050
16052
16053
16054
DI 14
16330
16131
16130
16132
16133
16134
DI 7
16260
16061
16060
16062
16063
16064
DI 15
16340
16141
16140
16142
16143
16144
DI 8
16270
16071
16070
16072
16073
16074
DI 16
16350
16151
16150
16152
16153
16154
Table 3-77: External discrete inputs - parameter IDs
Woodward
Page 169/339
Manual 37427
Discrete Outputs (LogicsManager)

The discrete outputs are controlled via the LogicsManager.
Please note the description of the LogicsManager starting on page 271.
Some outputs are assigned a function according to the application mode (see following table).
Relay
Number
Term.
None
{0}
Internal relay outputs

[R1]
30/31
[R2]
32/33
[R3]
34/35
[R4]
36/37
[R5]
38/39/40
[R6]
41/42
[R7]
80/81
[R8]
82/83
[R9]
84/85
[R10]
86/87
[R11]
88/89
GCB open
{1o}
Application mode
GCB open/close
{1oc}
GCB/MCB open/close
{2oc}
LogicsManager; pre-assigned with 'Ready for operation OFF'

LogicsManager; pre-assigned with 'Centralized alarm (horn)'
LogicsManager; pre-assigned with 'Starter'
LogicsManager; pre-assigned with 'Diesel: Fuel solenoid, Gas: Gas valve'
LogicsManager; pre-assigned with 'Warning alarm'
Command: open MCB
LogicsManager
Command: close GCB
LogicsManager
Command: open GCB
LogicsManager, pre-assigned with 'Mains decoupling'
Command: close MCB
LogicsManager; pre-assigned with 'Stop solenoid'
LogicsManager; pre-assigned with 'Auxiliary services'
LogicsManager; pre-assigned with 'Shut down alarm'
Table 3-78: Relay outputs - assignment
DE
EN
Ready for op. Off

Betriebsbe abgef.
CL2
12580
{0}
{1o}
{1oc}
{2oc}
Digital outputs: LogicsManager for Ready for operation OFF
LogicsManager
The "Ready for operation OFF" relay is energized by default if the power supply
exceeds 8 V. Once the conditions of the LogicsManager have been fulfilled, the
relay will be de-energized. This LogicsManager output may be configured with
additional conditions, which may signal a PLC an "out of operation" condition by
de-energizing the relay on terminals 41/42, like "shutdown alarm" or No "AUTO
mode" present. The LogicsManager and its default settings are explained on
page 271 in Appendix B: "LogicsManager".
CAUTION
The discrete output "Ready for operation OFF" must be wired in series with an emergency stop
function. This means that it must be ensured that the generator circuit breaker is opened and the
engine is stopped if this discrete output is de-energized. We recommend to signal this fault
independently from the unit if the availability of the plant is important.
DE
EN
Relay {x}
Relais {x}
CL2
12110
{0}
{1o}
{1oc}
{2oc}
Digital outputs: LogicsManager for relay {x}
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the relay will be
energized. The LogicsManager and its default settings are explained on page 271
in Appendix B: "LogicsManager".
Above parameter IDs refers to R 2. Refer to Table 3-79 for the parameter IDs of the parameters for R 3 to R 11.
Parameter ID
R1
12580
R2
12110
R3
12310
R4
12320
R5
12130
R6
12140
R7
12150
R8
12160
R9
12170
R 10
12180
R 11
12560
Table 3-79: Discrete outputs - parameter IDs
Page 170/339
Woodward
Manual 37427
External Discrete Outputs (LogicsManager)

If a Woodward IKD 1 or other external expansion board (Phoenix Contact) is connected to the easYgen via the
CAN bus, it is possible to use 16 additional discrete outputs.
The configuration of these external DOs is performed in a similar way like for the internal DOs. Refer to Table
3-80 for the parameter IDs of the parameters for external DOs 1 through 16.
Parameter ID
Parameter ID
DO 1
12330
DO 9
12410
DO 2
12340
DO 10
12420
DO 3
12350
DO 11
12430
DO 4
12360
DO 12
12440
DO 5
12370
DO 13
12450
DO 6
12380
DO 14
12460
DO 7
12390
DO 15
12470
DO 8
12400
DO 16
12480
Table 3-80: External discrete outputs - parameter IDs
Configure Analog Outputs

Configure Analog Outputs 1/2
The analog outputs 1 and 2 may either be configured as analog or PWM outputs. The analog outputs are prepared
for speed and voltage bias signal for a speed controller and voltage regulator with an output signal of 0 to 20 mA
/ 0 to 10 V by default. Table 3-81 shows the default values for the analog outputs 1 and 2 as well as two
configuration examples. Example 1 is for a generator active power output with a range of -20 kW to 220 kW via
a 4 to 20 mA signal (generator rated power = 200 kW). Example 2 is for a speed bias output via a PWM signal.
ID
Data source
Source value at minimal output
Source value at maximal output
Selected hardware type
User defined min. output value
User defined max. output value
PWM signal
PWM output value
5200
5204
5206
5203
5201
5208
5209
5202
5210
Analog Output 1
default values
00.03 Speed bias
0
10000
Off
0-20mA / 0-10V
----Off
---
ID
5214
5218
5220
5217
5215
5222
5223
5216
5224
Analog Output 2
default values
00.02 Voltage bias
0
10000
Off
0-20mA / 0-10V
----Off
---
Example 1
Example 2
01.24 Gen. total power

-1000 (-20 kW)
11000 (220 kW)
3
User defined
60.00 % (4 mA)
100.00 % (20 mA)
Off
---
00.03 Speed bias

0
10000
Off
User defined
0.00 %
100.00 %
On
6V
Table 3-81: Analog outputs 1/2 - parameter table
Parameter table
Level
Text
Configure analog outputs 1 / 2
Data source
PWM signal
PWM output level
Setting range
Default value
Analogmanager
-32000 to 32000
-32000 to 32000
Off / 1 / 2 / 3 / 4 / 5 / 6 / 7
refer to Table 3-85
0.00 to 100.00 %
0.00 to 100.00 %
On / Off
0.00 to 10.00 V
refer to Table 3-81

0
10000
Off
0-20mA / 0-10V
0.00 %
100.00 %
Off
10.00 V
Table 3-82: Application - standard values - configure analog outputs 1/2
Woodward
Page 171/339
Manual 37427
Configure Analog Outputs 3/4

In comparision to the analog outputs 1 and 2 are the outputs 3 and 4 purely prepared to 0/4 to 20 mA. The outputs
are freely scalable. Each analog source of the analog manager can be passed to this outputs.
ID
Data source
5228
5232
5234
5231
5229
5236
5237
Analog Output 3
default values
00.01 Engine Speed
0
10000
3
Off
-----
ID
5242
5246
5248
5245
5243
5250
5251
Analog Output 4
default values
00.01 Engine Speed
0
10000
3
Off
-----
Table 3-83: Analog outputs 3/4 - parameter table
Parameter table
Level
Text
Configure analog outputs 1 / 2
Data source
Setting range
Default value
Analogmanager
-32000 to 32000
-32000 to 32000
Off / 1 / 2 / 3 / 4 / 5 / 6 / 7
refer to Table 3-85
0.00 to 100.00 %
0.00 to 100.00 %
refer to Table 3-83

0
10000
3
0
0.00 %
100.00 %
Table 3-84: Application - standard values - configure analog outputs 3/4
NOTE
When a burden of 500 Ohm is applied to the analog outputs 3 and 4, the hardware type for voltage can
also be used.
Page 172/339
Woodward
DE
EN
Manual 37427
CL2
5200
5214
5228
5242
{0}
{1o}

Data source
Datenquelle
{1oc}
{2oc}
Analog output {x} [x = 1 to 4]: Data source
refer to text below
The data source may be selected from the available data sources. Use the "+" and "
" softkeys to scroll through the list of sources and confirm your selection with the
Enter softkey. Refer to Appendix C on page 305 for a list of all data sources.
Figure 3-18: Monitoring - analog outputs - data source selection
Analog output {x} [x = 1 to 4]: Source value at minimal output

Quellwert bei Max-Ausgabe
CL2 {0} {1o} {1oc} {2oc}
Analog output {x} [x = 1 to 4]: Source value at maximal output
DE
EN

Quellwert bei Min-Ausgabe
CL2 {0} {1o} {1oc} {2oc}
DE
EN
5204
5218
5232
5246
5206
5220
5234
5248
Woodward
-32000 to 32000
The value from the data source must exceed the value configured here to raise the
output signal above 0 %. Negative percentage values may be used to change the
sign, e.g. for power.
The entry format of the value depends on the selected data source. If the monitored
analog value has a reference value (refer to Appendix C: Reference Values on
page 310), the threshold is expressed as a percentage of this reference value (320.00 % to 320.00 %). If an analog input is monitored, the threshold refers to the
display value format (refer to Appendix C: Display Value Format on page 317 for
more information).
-32000 to 32000
If the value from the data source reaches the value configured here, the output
signal will reach 100 %. Negative percentage values may be used to change the
sign, e.g. for power.
The entry format of the value depends on the selected data source. If the monitored
analog value has a reference value (refer to Appendix C: Reference Values on
page 310), the threshold is expressed as a percentage of this reference value (320.00 % to 320.00 %). If an analog input is monitored, the threshold refers to the
display value format (refer to Appendix C: Display Value Format on page 317 for
more information).
Page 173/339
DE
EN
Manual 37427
CL2
5203
5217
5231
5245
{0}

Filter
{1o}
{1oc}
{2oc}
Analog output {x} [x = 1 to 4]: Filter time constant
Off / 1 / 2 / 3 / 4 / 5 / 6 / 7
A filter time constant may be used to reduce the fluctuation of an analog output
value. This filter time constant assesses the average of the signal according to the
following formula:
Cut off frequency =
1
20ms 2 2 N 1
, whereby "N" is the parameter.
Off ................ The analog output is displayed without filtering.

1.................... Cut-off-frequency = 7.96 Hz (filter time constant = 0.02 s)
DE
EN
Note: The filter is not applied to the analog output display value, i.e. the end value
of the analog output is displayed immediately.
CL2
5201
5215
5229
5243
{0}

Ausgangstyp
{1o}
{1oc}
{2oc}
Analog output {x} [x = 1 to 4]: Selected hardware type
select from list below
This parameter is used to configure the appropriate type of analog controller

signal. The range of the analog output is configured here. The available ranges are
listed below. It is possible to configure the following settings:
Off ................ No analog output signal will be issued.
user defined . A maximum range of +/-20 mA / +/-10 V may be limited using the
parameters 5208 and 5209 on page 175 to obtain a user defined
range.
Type
Current
Voltage
Setting in above
configuration screen
+/-20mA (+/-10V)
+/-10mA (+/-5V)
0 to 10mA (0 to 5V)
0 to 20mA (0 to 10V)
4 to 20mA
10 to 0mA (5 to 0V)
20 to 0mA (10 to 0V)
20 to 4mA
+/-20mA (+/-10V)
+/-10mA (+/-5V)
+/-3V
+/-2.5V
+/-1V
0 to 10mA (0 to 5V)
0.5V to 4.5V
0 to 20mA (0 to 10V)
10 to 0mA (5 to 0V)
4.5V to 0.5V
20 to 0mA (10 to 0V)
Jumper
necessary
no
yes
Range
+/-20mA
+/-10mA
0-10mA
0-20mA
4-20mA
10-0mA
20-0mA
20-4mA
+/-10V
+/-5V
+/-3V
+/-2.5V
+/-1V
0 to 5V
0.5 to 4,5V
0 to 10V
5 to 0V
4.5 to 0,5V
10 to 0V
Lower
level
-20 mA
-10 mA
0 mA
0 mA
4 mA
10 mA
20 mA
20 mA
-10 Vdc
-5 Vdc
-3 Vdc
-2.5Vdc
-1 Vdc
0 Vdc
0.5 Vdc
0 Vdc
5 Vdc
4.5 Vdc
10 Vdc
Upper
level
+20 mA
+20 mA
10 mA
20 mA
20 mA
0 mA
0 mA
4 mA
+10 Vdc
+5 Vdc
+3 Vdc
+2.5 Vdc
+1 Vdc
5 Vdc
4.5 Vdc
10 Vdc
0 Vdc
0.5 Vdc
0 Vdc
Table 3-85: Analog outputs - signal type selection
Page 174/339
Woodward
Manual 37427
DE
EN

Frei definierbares Min-Signal
CL2 {0} {1o} {1oc} {2oc}
5208
5222
5236
5250
Analog output {x} [x = 1 to 4]: User defined minimum output value
0 to 100 %
The minimum output value, which shall correspond with the minimum value of the
output range, must be entered here. This parameter is only active, if
parameter 5201 on page 174 is configured to "user defined".
Example: If the value configured here is 25 %, the maximum output range of +/20 mA / +/-10 V has a lower limit of -10 mA / -5 V.
DE
EN

Frei definierbares Max-Signal
CL2 {0} {1o} {1oc} {2oc}
5209
5223
5237
5251
Analog output {x} [x = 1 to 4]: User defined maximum output value
0 to 100 %
The maximum output value, which shall correspond with the maximum value of
the output range, must be entered here. This parameter is only active, if
parameter 5201 on page 174 is configured to "user defined".
DE
EN
Example: If the value configured here is 75 %, the maximum output range of +/20 mA / +/-10 V has a upper limit of 10 mA / 5 V.
CL2
{0}
DE
CL2
5210
5224
{1o}
EN
5202
5216
{0}
PWM signal
PWM Signal
{1oc}
{2oc}
PWM output level

PWM Ausgangslevel
Woodward
{1o}
{1oc}
{2oc}
Analog output {x} [x = 1 to 2]: PWM signal
On / Off
On................. A PWM signal will be output on the respective analog output. The
amplitude of the PWM signal to be utilized is configured in "PWM
output level" (parameter 5210 on page 175). If a PWM signal is
used, a jumper must be installed (refer to the wiring diagram in
manual 37426). The PWM signal will also be limited by
parameter 5201 on page 174 or parameters 5208 and 5209 on
page 175 if parameter 5201 is user defined.
Off ................ An analog signal will be output on the respective analog output.
Analog output {x} [x = 1 to 2]: PWM output level
0.00 to 10.00 V
If PWM has been enabled in parameter 5203 on page 174, the level of the PWM
signal may be adjusted here.
Page 175/339
Manual 37427
Configure Application: Configure Engine

Configure Application: Configure Engine, Engine Type
Parameter table
Level
Text
Configure engine type
Start/Stop mode logic
Preglow time
Preglow mode
Preglow criterion
Preglow temperature threshold
Ignition delay
Gas valve delay
Minimum speed for ignition
Setting range
Default value
Diesel / Gas / External

0 to 999 s
Always / Analog / Off
Analogmanager
-10 to 250 C
1 to 999 s
0 to 999 s
10 to 1800 rpm
Diesel
5s
Always
06.01
0 C
5s
5s
100 rpm
Table 3-86: Application - standard values - configure engine type
NOTE
DE
EN
All functions which are described in the following text, may be assigned by the LogicsManager to any
relay that is available via the LogicsManager and not assigned to another function.
CL2
3321
{0}
Start/Stop mode logic

Start/Stop Modus
{1o}
{1oc}
{2oc}
Engine: Type of engine
Diesel / Gas / External
Diesel or gas engine start/stop logic must be selected. The starting sequences are
described in the following sections. If this parameter is configured to "External" the
start/stop sequence must be done externally.
Engine: Diesel Engine

Start sequence
The relay "Preglow" will be energized for the preheating time period ("Preglow" is displayed). Following
preheating, the fuel solenoid is first energized and then the starter is engaged ("Start" is displayed). When the
configured firing speed is exceeded, the starter is disengaged and the fuel solenoid remains energized via the
firing speed. "Ramp to rated" is displayed until the engine monitoring delay timer expires and the start
sequence has finished.
If the engine fails to start, a start pause is initiated ("Start - Pause" is displayed). If the number of
unsuccessful start attempts reaches the configured value, an alarm message will be issued ("Start fail" is
displayed).
Stop sequence
After opening the GCB, the coasting time starts and the engine runs without load ("Cool down" is displayed).
On termination of the coasting time, the fuel solenoid is de-energized, and the engine is stopped ("Stop
engine" is displayed). If the engine cannot be stopped via the fuel solenoid, the alarm message "Eng. stop
malfunct." is displayed.
Start/stop diagram
The formula signs and indices mean:
tPRE ............... Auxiliary services prerun ................. [s] (parameter 3300 on page 186)
tPH ................. Preglow time .................................... [s] (parameter 3308 on page 177)
tST ................. Starter time ....................................... [s] (parameter 3306 on page 182)
tSP ................. Start pause ........................................ [s] (parameter 3307 on page 182)
tED................. Engine delayed monitoring .............. [s] (parameter 3315 on page 184)
tPOST .............. Auxiliary services postrun ................ [s] (parameter 3301 on page 186)
tCD ................ Cool down time ................................ [s] (parameter 3316 on page 185)
tGS ................. Generator stable time ....................... [s] (parameter 3415 on page 151)
Page 176/339
Woodward
DE
EN
Manual 37427
CL2
{0}
{1o}
DE
CL2
{0}
DE
CL2
3346
{1o}
EN
3347
{0}
{1oc}
{2oc}
Preglow mode
Vorglhmodus
EN
3308
Preglow time
Vorglhzeit
{1oc}
{2oc}
Preglow criterion
Vorglhen Kriterium
{1o}
{1oc}
{2oc}
Diesel engine: Preglow time [tPH]
0 to 999 s
Prior to each start, the diesel engine is preheated for this time (if a "0" has been
configured here the engine will be started without preglow). The display indicates
"Preglow".
Diesel engine: Preglow mode
Off / Always / Analog
This parameter dictates if and under what conditions a diesel engine is preheated.
Off ................ The diesel engine is never preheated before a start attempt.
Always ......... Before a start attempt the "Preheating" relay is always energized for
the preglow time (parameter 3308). After that a start attempt is
initiated.
Analog ......... A preglow sequence is initiated if the monitored analog input
temperature (coolant temperature) is below the configured threshold
(parameter 3309). The preglow sequence is enabled for the
configured preglow time (parameter 3308). After that a start attempt
is initiated.
Diesel engine: Preglow criterion
refer to text below
The preglow criterion may be selected from the available data sources. Use the
and softkeys to scroll through the list of variables and confirm your selection
with the softkey. Refer to Appendix C on page 305 for a list of all data sources.
Usually, a temperature measuring is selected here, which is measured via a sensor.
Figure 3-19: Configure application - engine - preglow criterion selection

DE
EN
Preglow temperature threshold

Vorglhen wenn Temperatur
CL2 {0} {1o} {1oc} {2oc}
3309
Woodward
Diesel engine: Preglow temperature threshold
-10 to 250 C
This is the temperature threshold, which must be exceeded to prevent a preheating

process, if parameter 3347 has been configured to "Analog".
Page 177/339
Page 178/339
[RPM]
Starting
Engine
monitoring ON
Fuel relay
Starter
Preglow
Auxiliary services
Start request
Firing speed
Start frequency
f control + time
Rated speed
tST
unsuccessful
0.5 s
tPH
tSP
0.5 s
successful
tST
[1/min; RPM]
tED
tPOST
Stopping
t [s]
t [s]
t [s]
t [s]
t [s]
t [s]
t [s]
Manual 37427
Figure 3-20: Start /stop sequence - diesel engine
Woodward
Manual 37427
Engine: Gas Engine

Start sequence
Function: The starter is engaged ("Turning" is displayed). Following the expiration of the firing delay time
and if the engine is rotating with at least the configured "minimum speed for ignition", the ignition is switched on
("Ignition" is displayed). Following the expiration of the gas valve delay, the gas valve is then enabled
("Start" is displayed). If the configured firing speed is exceeded, the starter is disengaged. The gas valve and
the ignition remain enabled via the firing speed. "Ramp to rated" is displayed until the engine monitoring
delay timer expires and the start sequence has finished.
If the configured "minimum speed for ignition" is not reached, a start pause is initiated ("Start - Pause" is
displayed) before the next start attempt.
Stop sequence
Function: After opening the GCB, the coasting time starts and the engine runs without load ("Cool down" is
displayed). On termination of the coasting time, the gas valve is closed or de-energized, and the engine is stopped
("Stop engine" is displayedy). If the engine cannot be stopped, the alarm message "Eng. stop
malfunct." is displayed. If no speed is detected anymore, the ignition remains active for 5 seconds so that the
remaining gas is able to combust.
CAUTION
It is imperative to connect an emergency stop circuit to discrete input DI 1 to be able to perform an
emergency stop by disabling the ignition in case the gas valve fails to close.
DE
EN
Start/stop diagram
The formula signs and indices mean:
tPRE ................ Auxiliary services prerun ............... [s] (parameter 3300 on page 186)
tST ................. Starter time .................................... [s] (parameter 3306 on page 182)
tSP.................. Start pause...................................... [s] (parameter 3307 on page 182)
tID .................. Ignition delay ................................. [s] (parameter 3310 on page 179)
tGD ................. Gas delay ....................................... [s] (parameter 3311 on page 179)
tED ................. Engine delayed monitoring ............ [s] (parameter 3315 on page 184)
tPOST .............. Auxiliary services postrun ............. [s] (parameter 3301 on page 186)
tCD ................. Cool down time ............................. [s] (parameter 3316 on page 185)
tIC .................. Ignition coasting ("post burning") . [s] (fixed to 5 seconds)
tGS ................. Generator stable time ..................... [s] (parameter 3415 on page 151)
CL2
{0}
DE
EN
3310
CL2
DE
EN
3311
CL2
3312
{0}
Ignition delay
Zndverzgerung
{1o}
{1oc}
{2oc}
Gas valve delay

Gasverzgerung
{1o}
{1oc}
{2oc}

Mindestdrehz. fr Zndung
{0}
Woodward
{1o}
{1oc}
{2oc}
Gas engine: Ignition delay [tID]
1 to 999 s
With gas engines often a purging operation is desired before starting. With the
engaging of the starter the ignition delay is started. The display indicates
"Turning". If the "Minimum speed for ignition" is reached after the expiration of
this time, the ignition is energized.
Gas engine: Gas valve delay [tGD]
0 to 999 s
By energizing the ignition relay the gas valve delay is started ("Ignition" is
displayed). After the time set here has expired, and as long as the speed is higher
than the minimum speed for ignition, the gas valve is enabled for the time
configured in parameter 3306 "Starter time" ("Start" is displayed). Once the
ignition speed has been reached, the gas valve remains opened. If the speed falls
below ignition speed, the gas valve will be closed and the "Ignition" relay is deenergized 5 seconds later.
Gas engine: Minimum speed for ignition
10 to 1.800 RPM
After expiration of the ignition delay the number of revolutions set here must be
reached, so the "Ignition" relay will be energized.
Page 179/339
Page 180/339
Starting
Engine
monitoring ON
Gas valve
Starter
Ignition
Auxiliary services
Start request
Minimum speed
for ignition
Firing speed
Rated speed
[RPM]
tPRE
unsuccessf.
tID
tSP
tID

will not be reached
successful
tST
[1/min; RPM]
tED
tIC
tPOST
Stopping
t [s]
t [s]
t [s]
t [s]
t [s]
t [s]
t [s]
Manual 37427
Figure 3-21: Start /stop sequence - gas engine - successful
Woodward
Woodward
Engine
monitoring ON
Gas valve
Starter
Ignition
Auxiliary services
Start request
Minimum speed
for ignition
Firing speed
Rated speed
[RPM]
tPRE
unsuccessf.
tID
tSP
[1/min; RPM]
tID
tGD
tST
Firing speed will

not be reached
unsuccessful

will not be reached
tIC
tSP
Manual 37427
Figure 3-22: Start /stop sequence - gas engine - unsuccessful
Page 181/339
Manual 37427
Configure Application: Configure Engine, Start/Stop

Parameter table
Level
Text
Configure start/stop
Start attempts
Start attempts critical mode
Starter time
Start pause time
Stop time of engine
Firing speed
LogicsManager for firing speed
Firing speed
Engine monitoring delay time
Cool down time
Cool down in STOP mode
Cool down without breaker
Auxiliary services prerun
Auxiliary services postrun
Setting range
Default value
1 to 20
1 to 20
1 to 99 s
1 to 99 s
1 to 99 s
5 to 60 Hz
Yes / No
LogicsManager
1 to 99 s
1 to 9999 s
Yes / No
Yes / No
0 to 9999 s
0 to 9999 s
3
10
5s
7s
10 s
15 Hz
No
(0 & 1) & 1
8s
180 s
Yes
No
0s
0s
DE
EN
Table 3-87: Application - standard values - configure start/stop
CL2
3302
{0}
Start attempts
Anzahl Startversuche
{1o}
{1oc}
{2oc}
DE
EN
DE
EN
Start attempts critical mode

Anzahl Startversuche Sprinkler
CL2 {0} {1o} {1oc} {2oc}
4102
CL2
{0}
{1o}
DE
CL2
{0}
{1o}
DE
EN
3307
CL2
3326
{0}
{1oc}
{2oc}
Start pause time

Startpausenzeit
EN
3306
Starter time
Einrckzeit Anlasser
{2oc}
Stop time of engine

Zeit fr Motorstop
{1o}
Page 182/339
{1oc}
{1oc}
{2oc}
Start alarm: Number of starting attempts
1 to 20
The control will attempt to start the engine with this number of start attempts. If
the engine fails to start after the configured number of attempts, an alarm will be
initiated. An engine has been successfully started if the ignition speed reaches the
configured firing speed and the delayed engine monitoring has expired.
Start alarm: Number of starting attempts in critical mode
1 to 20
If a critical operation mode (refer to Configure Application: Automatic, Critical

Mode (Sprinkler Operation, LogicsManager) on page 210) is initiated, the engine
will continue to attempt to start for the number of starts configured here. An
engine has been successfully started if the ignition speed reaches the configured
firing speed and the delayed engine monitoring has expired.
Engine: Maximum starter delay [tST]
1 to 99 s
This is the maximum time that the starter relay will remain energized ("Start"
display). If the LogicsManager output "Ignition speed reached" = TRUE, the
speed/frequency have reached firing speed, or the time has expired, the relay will
be de-energized.
Engine: Start pause time [tSP]
1 to 99 s
This is the delay time between the individual starting attempts. This time is also
used to protect the starter relay. The message "Start - Pause" is displayed.
Engine: Engine blocking
0 to 99 s
During this time a restart of the engine is blocked. This time should be configured
so that the engine is total shutdown to protect the starting circuit. Once speed from
the engine is no longer detected the time configured in this parameter is initiated.
The message "Stop engine" is displayed. The LogicsManager command
variable "Stop solenoid" (03.27) becomes TRUE as soon as the stop signal has
been issued and remains true until this timer has expired.
Woodward
Manual 37427
t [s]
Delayed engine
monitoring
Ignition speed
reached
Start request
Firing speed
Rated speed
[RPM]
[1/min; RPM]
tED
Firing Speed - Engine Monitoring Delay 2006-08-24.cdr
t [s]
t [s]
t [s]
Engine: Firing Speed And Engine Delayed Monitoring
Figure 3-23: Engine - firing speed and engine delayed monitoring
Woodward
Page 183/339
Manual 37427
NOTE
When the ignition speed is reached, the starter is disengaged under one of the following conditions:
The measurement via MPU is enabled (On):

Ignition speed is detected
Ignition speed (measured via the generator voltage) is detected
Conditions for "Ignition speed" (see LogicsManager) equal true.
The measurement via MPU is disabled (Off):

Ignition speed (measured via the generator voltage) is detected
Conditions for "Ignition speed" (see LogicsManager) equal true.
Generator frequency
Engine speed
LogicsManager
Off
On
Yes
Yes
No
Yes
Yes (if programmed)

Yes (if programmed)
DE
EN
Pickup
CL2
3313
{0}
{1o}
Firing speed
Znddrehzahl
{1oc}
{2oc}
Engine: Firing speed
5 to 60 Hz
After firing speed has been reached, the starter is disengaged and the time counter
for the engine delayed monitoring is activated. The firing speed is to be configured
low enough that it is always exceeded during regular generator operation.
Note: Frequency measurement via the generator voltage input is possible
beginning with 15 Hz or higher. If the MPU measurement is enabled, values down
to 5 Hz can be measured.
DE
EN
DE
EN
LogicsManager for firing speed

Logikm. fr Znddrehzahl
CL2 {0} {1o} {1oc} {2oc}
3324
CL2
12500
{0}
{1o}
Firing speed
Znddrehzahl
{1oc}
{2oc}
Engine: Firing speed via LogicsManager
Yes / No
Yes ............... The engine firing speed is additionally monitored by the

LogicsManager.
No ................ The firing speed is measured by the speed/frequency input (MPU),
not via the LogicsManager.
Engine: Firing speed reached via LogicsManager
LogicsManager
This screen is only visible if parameter 3324 is configured to Yes.

Once the conditions of the LogicsManager have been fulfilled the ignition speed
will be recognized as above minimum limit (e.g. via an oil pressure switch). The
LogicsManager and its default settings are explained on page 271 in Appendix B:
"LogicsManager".
After reaching the firing speed, the engine delayed monitoring timer is started. Upon expiration of this timer all
"engine delayed monitoring" configured alarms and discrete inputs will be enabled.
DE
EN
Engine monitoring delay time

Verzg. Motorberwach.
CL2 {0} {1o} {1oc} {2oc}
3315
Engine: Engine delayed monitoring [tED]
0 to 99 s
Delay between reaching the firing speed and activation of the monitoring of engine
speed delayed alarms (i.e. underspeed).
This timer should be configured in such a manner that it corresponds to the starting time of the engine plus any
possible startup transients. A GCB closure may take place after the expiration of this timer. Note: The GCB
closure can be initiated prior to engine delayed monitoring by configuring the LogicsManager "Undelay close
GCB" (parameter 12210 on page 151).
Page 184/339
Woodward
Manual 37427
DE
EN
Engine: Cool Down
CL2
3316
{0}
Cool down time

Motor Nachlaufzeit
{1o}
{1oc}
{2oc}
Engine: Cool down time [tCD]
1 to 999 s
Regular stop: If the engine performs a normal stop (start request is disabled or
change into STOP operating mode) or a stop caused by an alarm of alarm class
C/D, a cool down with an opened GCB is carried out. This time is programmable.
The message "Cool down" is displayed and the LogicsManager command
variable 04.10 becomes TRUE.
Stop by a class 'C' or 'D' alarm: If the engine is stopped by an alarm of this alarm
class, a cool down is carried out with an opened GCB. This time is programmable.
Stop by a class 'E' or 'F' alarm: If the engine is stopped by an alarm of this alarm
class, the engine is shutdown without a cool down immediately.
NOTE
DE
EN
If a critical operation mode (refer to Configure Application: Automatic, Critical Mode (Sprinkler
Operation, LogicsManager) on page 210) is initiated, the time configured in critical mode postrun
(parameter 4109) will be used instead of the cool down time.
CL2
DE
EN
3319
CL2
3322
Cool down in STOP mode

Nachlauf Betriebsart STOP
{0}
{1o}
{1oc}
{2oc}
Cool down without breaker

Nachlauf ohne LS
{0}
Woodward
{1o}
{1oc}
---
{2oc}
---
Engine: Cool down time in STOP mode
Yes / No
Yes ............... A cool down will be performed if the genset is changed to STOP
operation mode.
No ................. No cool down will be performed if the genset is changed to STOP
operation mode.
Engine: Cool down without breaker
Yes / No
This parameter may be used to perform a cool down if the aplication mode
(parameter 3401 on page 139) is configured to "None" or "GCB open".
Yes ............... A cool down will be performed if a start signal is disabled or a stop
signal is enabled.
No ................. No cool down will be performed if a start signal is disabled or a stop
signal is enabled.
Page 185/339
Manual 37427
Engine: Auxiliary Operations

The auxiliary operations start, as soon as the engine is to be started or a running engine is detected.
At the same time, the discrete output for the auxiliary services (LogicsManager 03.01) will be enabled. This
discrete output remains enabled as long as speed is detected or if the controller is in the MANUAL mode.
Start command
LogicsManager 03.30
tPRE
engine stop
LogicsManager 03.01
Auxiliary services
engine start
Motor stop
LogicsManager 03.31
tPOST
Engine speed
DE
EN
Figure 3-24: Engine - Auxiliary services timing
CL2
3300

Hilfsbetriebe Vorlauf
{0}
{1o}
{1oc}
{2oc}
Engine: Prerun auxiliary operation (start preparation) [tPRE]
0 to 999 s
CAUTION:
During an emergency start this delay time "auxiliary prerun" is not
initialized. The engine will be started immediately.
DE
EN
Prior to a start sequence being initiated, the discrete output for the auxiliary services
prerun (LogicsManager 03.30) remains enabled for the configured amount of time
to permit engine related operations (i.e. open louvers) to be performed. While this
discrete output is enabled the control screen will display the message
"Aux.serv.prerun" for the configured time.
The auxiliary services discrete output disables when the operation mode is changed
from the MANUAL operation mode or, if engine speed is no longer detected, when
the discrete output for the auxiliary services postrun (LogicsManager 03.31) is
disabled.
CL2
3301

Hilfsbetriebe Nachlauf
{0}
{1o}
Page 186/339
{1oc}
{2oc}
Engine: Coasting auxiliary operation (post operation) [tPOST]
0 to 999 s
After each engine stop (the engine stop timer has expired), the discrete output for
the auxiliary services postrun (LogicsManager 03.31) remains energized for an
adjustable time (i.e. operate a cooling pump). If the operating mode is changed
from MANUAL to STOP or AUTOMATIC without a start command the relay
remains energized for this period of time. The message "Aux.serv.postrun"
will be displayed on the control unit screen. In the "MANUAL" operating mode
this relay output is not used.
Woodward
Manual 37427
Configure Application: Configure Engine, MPU

Parameter table
Level
Text
Configure MPU
MPU input
Fly wheel teeth
Setting range
Default value
On / Off
2 to 260
On
118
Table 3-88: Application - standard values - configure MPU
DE
EN
To configure the MPU input, the Number of teeth on the flywheel detected by the magnetic pick up (MPU) or the
number of pickup pulses per revolution of the engine must be configured:
CL2
{0}
DE
CL2
1602
{1o}
EN
1600
{0}
MPU input
Pickup
{1oc}
{2oc}
Fly wheel teeth

Anzahl Pickup-Zhne
{1o}
{1oc}
{2oc}
Pickup
On / Off
On ................ Speed monitoring of the engine is carried out by the MPU.

Off ................ Speed/frequency monitoring of the generator set (the engine) is
performed by measuring the frequency of the generator. There is no
MPU wired to this unit.
Number of flywheel teeth
2 to 260
Number of pulse per revolution/teeth on the flywheel.
Table 3-89 shows the speed measuring range for various flywheel teeth numbers (parameter 1602) and rated
speeds (parameter 1601 on page 37) for a minimum signal voltage of 2 V.
Fly wheel
teeth
5
5
5
5
10
10
10
10
10
25
25
25
25
25
50
50
50
50
50
100
100
100
100
100
150
150
150
150
150
200
200
200
200
200
260
260
260
Rated speed
[rpm]
1500
1800
3000
3600
750
1500
1800
3000
3600
750
1500
1800
3000
3600
750
1500
1800
3000
3600
750
1500
1800
3000
3600
750
1500
1800
3000
3600
750
1500
1800
3000
3600
750
1500
1800
Minimum
voltage [V]
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Speed measuring
range [rpm]
700 to 10000
700 to 10000
700 to 10000
700 to 10000
350 to 10000
350 to 10000
350 to 10000
350 to 10000
350 to 10000
135 to 10000
135 to 10000
135 to 10000
135 to 10000
135 to 10000
65 to 10000
65 to 10000
65 to 10000
65 to 10000
65 to 10000
35 to 5000
35 to 5000
35 to 5000
50 to 5000
50 to 5000
25 to 5000
35 to 5000
35 to 5000
35 to 5000
35 to 5000
20 to 3850
25 to 3850
25 to 3850
25 to 3850
25 to 3850
15 to 2885
22 to 2885
22 to 2885
Table 3-89: MPU input - typical configurations

Woodward
Page 187/339
Manual 37427
Configure Application: Configure Engine, Idle Mode

When the engine is operated at idle speed, undervoltage, underfrequency, and underspeed monitoring as well as
the monitoring of the flexible limits 13 through 16 are not performed. This function allows for a controlled
operation of an engine without alarm messages at a lower speed (below the configured underspeed monitoring
values) for e.g. a warm-up operation with low emission. The frequency controller output does not control the idle
speed; it will remain in initial state position. The GCB cannot be closed in idle mode. A message may be output
to a relay here using the LogicsManager (Idle mode is active, command variable 04.15), e.g. as a signal for a
speed controller. The display indicates "Idle run active" during idle mode.
Parameter table
Level
Text
Configure idle mode
Auto idle mode
Constant idle run
Automatic idle time
During emergency / critical
Setting range
Default value
LogicsManager
LogicsManager
1 to 9999 s
Yes / No
(0 & 1) 0
(0 & 1) & 1
30 s
No
DE
EN
Table 3-90: Application - standard values - configure idle mode
CL2
{0}
DE
EN
12570
Auto idle mode

Automatic Idle Modus
CL2
12550
{0}
{1o}
{1oc}
{2oc}
Constant idle run

Dauernd Idle Modus
{1o}
{1oc}
{2oc}
Engine: LogicsManager automatic idle mode
LogicsManager
Once the conditions of the LogicsManager have been fulfilled the engine will be
operated in idle mode automatically for the configured time during start-up.
Monitoring is limited as described above. This function may always be configured
to "1" for example. The LogicsManager and its default settings are explained on
page 271 in Appendix B: "LogicsManager".
Engine: LogicsManager continuous idle mode
LogicsManager
As long as the conditions of the LogicsManager have been fulfilled the engine will
be continuously operated in idle mode. Monitoring is limited as described above. A
key switch via a DI may be configured here for example. The LogicsManager and
its default settings are explained on page 271 in Appendix B: "LogicsManager".
Note: The idle mode is blocked if the GCB is already closed.
Engine: Time for automatic idle mode
During emergency / critical

Whrend Notstrom/Sprinkler
CL2 {0} {1o} {1oc} {2oc}
3329
Engine: Idle mode possible during emergency / critical operation
DE
EN
DE
EN
Automatic idle time

Zeit fr Automatic Idle Modus
CL2 {0} {1o} {1oc} {2oc}
3328
1 to 9999 s
The automatic idle mode is active for the time configured here. Monitoring is
limited as described above during this time.
Yes / No
Yes ............... If an emergency or critical operation is enabled, the engine will go to

rated speed only after completing the configured idle mode.
No ................ If an emergency or critical operation is enabled, no idle run will be
performed the engine will go directly to rated speed.
NOTE
The normal operation monitoring limits will be enabled again, if one of the following conditions is
fulfilled:
Idle mode has ended and generator frequency and voltage are within the operating range of the
generator (refer to
Configure Monitoring: Generator, Operating Voltage / Frequency on page 48).
Idle mode has ended and engine delayed monitoring (parameter 3315 on page 184) has expired.
NOTE
The flexible limits 13 through 16 are disabled during idle mode operation (refer to Configure
Monitoring: Flexible Limits on page 119).
Page 188/339
Woodward
Manual 37427
Configure Application: Configure Emergency Run

NOTE
The emergency power operation is possible only in application mode {2oc} (2 power circuit breakers).
If the LogicsManager outputs 'Stop request in AUTO' or 'Inhibit emergency run' are TRUE, an
emergency power operation may be prevented or interrupted from an external source.
Prerequisite: The emergency power function can only be activated for synchronous generators with
parameter 2802. Emergency power is carried out in operating mode AUTOMATIC regardless of the status of the
LogicsManager output 'Start request in AUTO' (LogicsManager).
The display indicates "Emergency run" during emergency power operation.
The following principles are observed in case of an emergency power operation:
If an emergency power operation is initiated, the engine is started automatically, unless the start sequence is
interrupted via an alarm or prevented via the LogicsManager or the operating mode is changed.
The GCB can be closed regardless of the engine delay time if the generator frequency and voltage are within
the configured operating limits (refer to Configure Monitoring: Generator, Operating Voltage / Frequency on
page 48) if the parameter "Undelay close GCB" (parameter 12210 on page 151) has been set accordingly
(default setting).
If the mains return during an emergency power operation (GCB is closed), the mains settling time
(parameter 2801 on page 83) must expire before the load is transferred from the generator to mains operation.
Activation of emergency power: If the mains are not within the configured frequency and voltage operating
limits (refer to Configure Monitoring: Mains, Operating Voltage / Frequency on page 83) for at least the time
configured in the parameter "Mains fail delay time" (parameter 2800), an emergency power operation is
activated.
MCB malfunction: An emergency power operation will be performed, if the control is not able to close or
recluse the MCB and the alarm "Fail to close MCB" occurs.
Mains rotation field alarm: If the mains returns after a mains failure with a reversed rotation direction the
generator remains in emergency power operation until the mains rotation matches the rotation of the generator
set.
NOTE
The generator will not start upon a mains rotation field alarm, but it will keep on running if it has
already started.
Woodward
Page 189/339
Manual 37427
Parameter table
Level
Text
Configure emergency run
On / Off
Mains fail delay time
Emerg. start with MCB failure
Inhibit emerg. run
Break emerg. In critical mode
Setting range
Default value
On / Off
0.00 to 99.99 s
Yes / No
LogicsManager
0 to 999 s
On
3.00 s
Yes
(0 & 1) & 1
5s
Table 3-91: Application - standard values - configure emergency run
DE
EN
On / Off
Ein/Aus
CL2
{0}
---
DE
EN
2802
CL2
2800
{0}
---
{1o}
---
{1oc}
---
{2oc}
Mains fail delay time

Startverzgerung
{1o}
---
{1oc}
---
{2oc}
DE
EN
DE
EN
Emerg. start with MCB failure

Bei NLS-Fehler aktivieren
CL2 {0} {1o} {1oc} {2oc}
------3408
CL2
12200
{0}
---
Inhibit emerg. run

Kein Notstrombetrieb
{1o}
---
{1oc}
---
{2oc}
DE
EN
Break emerg. in critical mode

Pause Notstrom bei Sprinkler
CL2 {0} {1o} {1oc} {2oc}
------4101
Page 190/339
Emergency power: Monitoring
On / Off
On ................ If the unit is in the AUTOMATIC operating mode and a mains fault
occurs according to the following parameters, the engine is started
and an automatic emergency operation is carried out.
Off................ No emergency operation is carried out.
Emergency power: Mains failure: Start delay
0.00 to 99.99 s
To start the engine and to carry out an emergency operation the monitored mains
must be failed continuously for the minimum period of time set with this
parameter. This delay time starts only if the easYgen is in AUTOMATIC operating
mode and emergency power is activated.
Emergency power: Emergency operation by MCB failure
Yes / No
Emergency power operations may be configured with the failure of the MCB in
addition to a loss of power on the mains supply. An MCB breaker alarm is
indicated if parameter "MCB monitoring" (parameter 2620 on page 117) is
configured "On".
Emergency power: Inhibit emergency power
LogicsManager
Once the conditions of the LogicsManager have been fulfilled the emergency
power operation will be terminated or blocked. The LogicsManager and its default
settings are explained on page 271 in Appendix B: "LogicsManager".
Emergency power: Override emergency operations in critical mode
0 to 999 s
The emergency power operations are overridden for the configured time when the
critical mode starts in order to supply the complete generator power to the sprinkler
pump.
Woodward
Manual 37427
Configure Application: Configure Automatic Run

Configure Application: Automatic, Start In AUTOMATIC Operating Mode (LogicsManager)
The start of the engine can be performed via different logical conditions. This can be:
a discrete input
a temperature level
an interface start condition
a start request from the LDSS function
a timer
any logical combination
If this logical output becomes TRUE in AUTOMATIC operating mode, the generator starts and the GCB will be
closed. The simultaneous activation of other LogicsManager outputs (e.g. Stop req. in Auto) may affect this
function.
The breaker handling depends on the configured application mode and breaker logic.
NOTE
Refer to Figure 3-25 and Priority Hierarchy of the Logical Outputs on page 275 for the priority of the
logical outputs in case that more than one logical output is TRUE.
Parameter table
Level
Text
Configure automatic run
Start req in AUTO
Stop req. in AUTO
Start w/o load
Startup in mode
Operat. mode AUTO
Operat. mode MAN
Operat. mode STOP
Setting range
Default value
LogicsManager
LogicsManager
LogicsManager
STOP / AUTO / MAN / Last
LogicsManager
LogicsManager
LogicsManager
(09.02 0) 0
(0 & 1) & 1
(0 & 1) & 1
STOP
(0 & 1) & 1
(0 & 1) & 1
(0 & 1) & 1
DE
EN
Table 3-92: Application - standard values - configure automatic run
CL2
12120
{0}
Woodward
Start req in Auto

Startanf. in Auto
{1o}
{1oc}
{2oc}
Start request in operation mode AUTOMATIC
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the control issues a
start request in AUTOMATIC mode. The LogicsManager and its default settings
Page 191/339
Manual 37427
DE
EN
Configure Application: Automatic, Stop In AUTOMATIC Operating Mode (LogicsManager)

If this logical output becomes TRUE, it inhibits all other start processes (e.g. Start req. in Auto, emergency
power, etc.). Stopping of the engine can be initiated externally via a discrete input or any logical combination.
CL2
12190
{0}
Stop req. in Auto

Stopanf. in Auto
{1o}
{1oc}
{2oc}
LogicsManager
Stop request in operation mode AUTOMATIC
Once the conditions of the LogicsManager have been fulfilled, the control issues a
stop request in AUTOMATIC mode. The LogicsManager and its default settings
Engine Start Conditions in AUTOMATIC

LM 00.09: Start request in AUTO
LM 00.11: Inhibit
emergency run
Emergency run
LM 00.10:
Stop request in AUTO
LM 00.86:
Load-dependent
start/stop
Shutdown alarm
Load-dependent start
LM 00.38: Critical mode start (with closed GCB parameter ID 4100 = YES)
Engine
start
LM 00.38: Critical mode start (without closed GCB parameter ID 4100 = NO)
LM 00.19: Start without load
Shutdown alarm
LM = LogicsManager function No.

Internally evaluated
TRUE
CLOSED
TRUE
OPENED
Figure 3-25: Automatic run - engine start conditions
Page 192/339
Woodward
Manual 37427
Configure Application: Automatic, Load-Dependent Start/Stop (LDSS)

Refer to Appendix G: LDSS Formulas on page 332 for all formulas related with the LDSS function.
Load-dependent start/stop may either be performed according to a system reserve power or the generator load
depending on the configuration of the "Start stop mode" (parameter 5752 on page 196).
Configure Application: Automatic, Load-Dependent Start/Stop: System Reserve Power
If the "Start stop mode" (parameter 5752 on page 196) is configured to "Reserve power", load-dependent start
stop is performed in a way that a configured minimum reserve power is maintained in the system. This means
that there is always enough reserve power for load swings on the busbar regardless of the generator load. The
actual reserve power in the system is the total rated power of all gensets on the busbar minus the actual total
generator real power.
This functionality provides high system reliability and is intended for applications that require a dedicated reserve
power on the busbar, independent of the number of gensets on the busbar.
The following parameters need to configured for this operation:
Parameter ID
5760
5761
5767
Parameter text
IOP Reserve power
IOP Hysteresis
MOP Minimum load
5768
MOP Reserve power
5769
MOP Hysteresis
Note
only for isloated operation
only for mains parallel
operation
operation
operation
Table 3-93: Load-dependent start/stop - parameters for reserve power operation
Isolated Operation
PReserve = Prated active PGN real active
Prated active = PRatedGen[1] +PRatedGen[2] + + PRatedGen[n] (total rated power of all gensets on the busbar in the system)
PGN real active = PActualGen[1] +PActualGen[2] + + PActualGen[n] (total actual load of all gensets on the busbar in the
system)
If the reserve power falls below the IOP reserve power threshold (parameter 5760), another genset will be added.
PReserve < PReserveIOP
If the reserve power exceeds the IOP reserve power threshold (parameter 5760) plus the hysteresis
(parameter 5761) plus the rated load of the genset, the genset will be stopped. The hysteresis is intended to
prevent frequent starting and stopping of gensets in case of small load variations.
PReserve > Preserve isolatedIOP + Physteresis IOP + PRatedGen
Woodward
Page 193/339
Manual 37427
Mains Parallel Operation (mains import power control)

PReserve = Prated active PGN real active
Prated active = PRatedGen[1] +PRatedGen[2] + + PRatedGen[n] (total rated power of all gensets on the busbar in the system)
PGN real active = PActualGen[1] +PActualGen[2] + + PActualGen[n] (total actual load of all gensets on the busbar in the
system)
If the required generator load set point for the control at the mains interchange point exceeds the MOP minimum
load threshold (parameter 5767), the first genset will be added.
PMN setpoint PMN real > PMOP minimum
If at least one genset is supplying the load in parallel with the mains and the reserve power falls below the reserve
power threshold (parameter 5768), another genset will be added.
PReserve < Preserve parallel
If at least two gensets are supplying the load in parallel with the mains and the reserve power exceeds the MOP
reserve power threshold (parameter 5768) plus the hysteresis (parameter 5769) plus the rated load of the genset,
the genset will be stopped. The hysteresis is intended to prevent frequent starting and stopping of gensets in case
of small load variations.
PReserve > Preserve parallel + Physteresis MOP + PRatedGen
If one genset is supplying the load in parallel with the mains and the generator load exceeds the MOP minimum
load threshold (parameter 5767) minus the hysteresis (parameter 5769), the genset will be stopped. The hysteresis
is intended to prevent frequent starting and stopping of gensets in case of small load variations.
PMN setpoint PMN real + PGN real active < PMOP minimum Physteresis MOP
Configure Application: Automatic, Load-Dependent Start/Stop: Generator Capacity Utilization
If the "Start stop mode" (parameter 5752 on page 196) is configured to "Generator load", load-dependent start
stop is performed in a way that the next genset will be started if all gensets in operation reach the maximum
generator load (parameter 5762 or 5770 "IOP/MOP Max. generator load"), a configured percentage (e.g. 80%)
of the rated power. In order to stop one generator, the load of all gensets in operation must fall below the
minimum generator load (parameter 5763 or 5771 "IOP/MOP Min. generator load"), a configured percentage
(e.g. 30%) of the rated power. There are different set points for isolated and mains parallel operation.
An additional dynamic parameter (parameter 5757 or 5758 "IOP/MOP Dynamic") prevents the gensets from
being started and stopped continusouly if only a few gensets are in operation. Refer to the description of the
dynamic parameters for detailed information.
This function provides an easy calculation for the start of the next genset.
The following parameters need to configured for this operation:
Parameter ID
5757
5758
Parameter text
IOP Dynamic
MOP Dynamic
5767
MOP Minimum load
5769
MOP Hysteresis
5770
MOP Max. generator laod
Note
operation
operation
operation
operation
Table 3-94: Load-dependent start/stop - parameters for generator load operation
Page 194/339
Woodward
Manual 37427
Isolated Operation
If the configured maximum generator capacity utilization is exceeded, another genset will be added.
PGN real active > Pmax. load isolated
If the configured minimum generator capacity utilization has been fallen below, a genset will be stopped
depending on the dynamic setting. (refer to parameter 5757 on page 203 for detailed information).
PGN real active < Pmin. load isolated
Mains Parallel Operation (mains import power control)
If the required generator load set point for the control at the mains interchange point exceeds the MOP minimum
load threshold (parameter 5767), the first genset will be added.
PMN setpoint PMN real > PMOP minimum
If at least one genset is supplying the load in parallel with the mains and the total generator load exceeds the
MOP maximum generator load threshold (parameter 5770), another genset will be added.
PGN real active > Pmax. load parallel
If at least two gensets are supplying the load in parallel with the mains and the configured minimum generator
capacity utilization has been fallen below, a genset will be stopped depending on the dynamic setting. (refer to
parameter 5758 on page 207 for detailed information)
PGN real active < Pmin. load parallel
If one genset is supplying the load in parallel with the mains and the generator load exceeds the MOP minimum
load threshold (parameter 5767) minus the hysteresis (parameter 5769), the genset will be stopped. The hysteresis
is intended to prevent frequent starting and stopping of gensets in case of small load variations.
Configure Application: Automatic, Load-Dependent Start/Stop: Generator Selection
If a genset is to be started, the genset with the highest priority configured will be started. If a genset is to be
stopped, the genset with the lowest priority configured will be stopped. If all gensets have the same priority, the
next genset is selected according to the size of engine, i.e. the genset combination, which allows an optimum
efficiency will be used. If all gensets have the same rated load or this parameter is disabled, the remaining hours
until the next maintenance are considered. If these are also the same, the genset with the lowest generator number
will be started first or stopped last.
Priority order:
1.
2.
3.
4.
Priority (parameter 5751)

Efficiency (size of engines) (parameter 5754)
Service hours (parameter 5755)
Generator (device) number (parameter 1702)
Woodward
Page 195/339
Manual 37427
The load-dependent start/stop function requires the following conditions have been met:
The control has been placed in AUTOMATIC operating mode
A start request (Start req. in AUTO, Emergency run) is active
All load sharing parameters are configured identically for all generators participating in load sharing (refer to
Configure Monitoring: Miscellaneous, Multi-Unit on page 135)
The mains interchange load control (import/export power) has been enabled or the gensets are in isolated
operation
The conditions of the LogicsManager function "Load-dependent start/stop" have been fulfilled
Parameter table
Level
Text
Configure load dependent start/stop
LD start stop
Start stop mode
Dead busbar start mode
Base priority
LDSS priority 2
LDSS priority 3
LDSS priority 4
Fit size of engines
Fit service hours
Changes of engines
Minimum running time
Setting range
Default value
LogicsManager
Reserve power / Generator laod
All / LDSS
1 to 32
LogicsManager
LogicsManager
LogicsManager
Yes / No
Off / Equal / Staggered
Off / All 32h /All 64h / All 128h
0 to 32000 s
(0 & !04.27) & !00.19

Reserve power
All
5
(0 & 1) & 1
(0 & 1) & 1
(0 & 1) & 1
No
Off
Off
180 s
Table 3-95: Application - standard values - configure load dependent start/stop
DE
EN
LD start stop
Lastabh. Zu/Abs.
CL2
{0}
{1o}
DE
EN
12930
CL2
5752
{0}
{1oc}
{2oc}
Start stop mode

Start Stop Modus
{1o}
{1oc}
{2oc}
DE
EN
Dead busbar start mode

Schwarze Schiene Start Modus
CL2 {0} {1o} {1oc} {2oc}
5753
Load-dependent start stop
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the load-dependent
start/stop function is enabled. The LogicsManager and its default settings are
Load-dependent start stop: Start stop mode
Reserve power / Generator load
Reserve power .. Load-dependent start stop is performed in a way that a configured

minimum reserve power is maintained in the system. The reserve
power is the total generator rated power minus the total actual
generator power. If the reserve power falls below the threshold,
another genset will be started. If the reserve power is sufficient to
stop one genset without falling below the threshold, a genset will be
stopped.
Generator load . Load-dependent start stop is performed in a way that a configured
maximum generator capacity utilization is not exceeded. If the
generator capacity utilization exceeds this threshold, another genset
will be started. If the generator capacity utilization is low enough to
stop one genset without exceeding the threshold again, a genset will
be stopped.
Load-dependent start stop: Dead busbar start mode
All / LDSS
All ................ All available gensets will be started in case of a dead busbar and
remain connected to the busbar for the minimum running time
(parameter 5759). Then the gensets will be stopped according to the
configured LDSS procedure. The start delay is configured in
parameter 2800 (Mains fail delay time).
LDSS ........... The start of the gensets will be performed according to the
configured LDSS priority in case of a dead busbar.
Note: This function cannot be used as an emergency power function in mains
parallel operations because it cannot control the MCB operation. If the MCB shall
be operated, the emergency run function (parameter 2802) must be enabled
Page 196/339
Woodward
Manual 37427
DE
EN
Base priority
Grund Prioritt
CL2
{0}
DE
EN
5751
CL2
{0}
{1o}
DE
CL2
{0}
{1o}
DE
EN
12925
CL2
DE
EN
12924
CL2
5754
{0}
{1oc}
{2oc}
LDSS Priority 2
LZA Prioritt 2
EN
12926
{1o}
{1o}
{1oc}
{2oc}
LDSS Priority 3
LZA Prioritt 3
{1oc}
{2oc}
LDSS Priority 4
LZA Prioritt 4
{1oc}
{2oc}
Fit size of engine

Auswahl nach Nennleistung
{0}
{1o}
{1oc}
{2oc}
Load-dependent start stop: Base priority
1 to 16
The priority of the genset in the load-dependent start/stop network is configured

with this parameter (refer to Configure Application: Automatic, Load-Dependent
Start/Stop: Generator Selection on page 195). The lower the number configured
here, the higher the priority. This priority may be overridden by the LDSS Priority
parameters (parameters 12924, 12925, and 12926).
Load-dependent start stop: Priority 2
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the load-dependent
start/stop priority will be set to 2 (the highest priority is valid). The LogicsManager
and its default settings are explained on page 271 in Appendix B:
"LogicsManager".
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the loaddependent start/stop priority will be set to 3 (the highest priority is valid). The
"LogicsManager".
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the loaddependent start/stop priority will be set to 4 (the highest priority is valid). The
"LogicsManager".
Load-dependent start stop: Fit size of engine
Yes / No
This parameter defines whether the start/stop priority order (refer to Configure
Application: Automatic, Load-Dependent Start/Stop: Generator Selection on
page 195) considers the size of the engine (generator rated power) or not. In case
of different sized gensets, the control can start a genset combination which results
in optimum efficiency. The fuel efficiency may be optimized when this parameter
is enabled. This parameter may be disabled if all generators have the same size.
Yes ............... The priority order considers the engine size for the start of the next
engine for gensets with the same priority.
No ................ The priority order does not consider the rated power of the engines
to fit the best size of engines.
Woodward
Page 197/339
Manual 37427
DE
EN
Fit service hours

Auswahl nach Wartungsintervall
{1o}
{1oc} {2oc}
CL2 {0}
5755
Page 198/339
Load-dependent start stop: Fit service hours
Off / Staggered / Equal
Off ................ The remaining hours until the next service is required are not
considered when evaluating the engines to be started.
Staggered ..... The remaining hours until the next service is required are
considered when evaluating the engines to be started for gensets
with same priority. The gensets are utilized in a way that the
maintenance may be performed at different times to ensure that not
all gensets have a downtime due to a maintenance at the same time.
The genset with the lowest hours until the next service will be
started first.
Equal ............ The remaining hours until the next service is required are
considered when evaluating the engines to be started for gensets
with same priority. The gensets are utilized in a way that the
maintenance may be performed at the same time for all gensets.
The genset with the highest hours until the next service will be
started first.
Woodward
DE
EN
Manual 37427
CL2
5756
{0}

Changes of engines
Aggregatewechsel
{1o}
{1oc}
{2oc}
Load-dependent start stop: Changes of engines
Off / All 32h / All 64h / All 128h
This parameter is only effective if fit service hours (parameter 5755) is

configured to "Equal".
Engine sequencing may be configured to start and stop engines according to the
time remaining until the maintenance hours counter (parameter 2550) expires
(counter reaches 0 hrs). The easYgen-2000 Series takes the time remaining on the
maintenance hours counter and divides it by the service hours group
(32/64/128 h) configured in this parameter to determine the individual units time
group. A generator with a larger time group number has more time remaining
before the maintenance hours timer expires and is considered to be the higher
priority generator. If two generators are in the same time group, the configured
generator number determines which generator is the higher priority and will be
started first. This functionality enables the end user to have multiple generators
due for service at approximately the same time.
Off................ No engine change will be performed. The engines are selected
according to the setting of parameter 5755 (Fit service hours) with
1 hour spacing in case of load changes.
All 32/64/128h If parameter 5754 (Fit size of engine) is configured to "Yes",
only engines with the same rated power and priority are changed, if
it is configured to "No", engines with the same priority are changed
depending on the service hours and generator number. All engines
are divided into 32/64/128 service hour groups. An engine change
is performed if one engine changes to another group in
32/64/128 hour spacing.
Example 1: "Changes of engines" is configured to "All 64h"
Generator 1 has 262 maintenance hours remaining
The time group for generator 1 is calculated as: 262h/64h = 4.09 = Time group 4
Both generators are in time group 4. Time group 4 consists of any generator that
the time group calculation total ranges from 4.00 through 4.99. In this instance
the assigned generator number is used to determine which generator is brought
online. Generator 1 will be started.
Example 2: "Changes of engines" is configured to "All 64h"
Generators 1 and 3 are in time group 4. Time group 4 consists of any generator
that the time group calculation total ranges from 4.00 through 4.99. Generator 2 is
in time group 5. Time group 5 consists of any generator that the time group
calculation total ranges from 5.00 through 5.99. In this instance the largest time
group will determine which generator is brought online. Generator 2 will be
started because it is in time group 5.
Woodward
Page 199/339
DE
EN
Manual 37427
CL2
5759
Minimum running time

Aggregate Mindestlaufzeit
{0}
Page 200/339
{1o}
{1oc}
{2oc}
Load-dependent start stop: Minimum running time
0 to 32000 s
If a genset has been started by the LDSS function, it continues to operate at least
for this time even if it would have been stopped before. This timer is started with
the closure of the GCB. If an emergency run is active (refer to Configure
Application: Configure Emergency Run on page 189) and the mains return, this
timer will be overridden and the load is transferred back to the mains after the
mains settling time (parameter 2801 on page 83) has expired.
Woodward
Manual 37427
Configure Application: Automatic, Load-Dependent Start/Stop: Isolated Parallel Operation (IOP)

In case of an isolated parallel operation (MCB open), the first genset will be connected to the de-energized
busbar. At least one genset must be in operation in isolated operation. There are dedicated LDSS parameters for
isolated parallel operation because the supply of the load is important here.
Parameter table
Level
Text
Setting range
Configure load dependent start/stop isolated operation
IOP Reserve power
1 to 999999 kW
IOP Hysteresis
5 to 65000 kW
IOP Max. generator load
0 to 100 %
IOP Min. generator load
0 to 100 %
IOP Dynamic
Low / Moderate / High
IOP Add on delay
0 to 32000 s
IOP Add on delay at rated load
0 to 32000 s
IOP Add off delay
0 to 32000 s
Default value
100 kW
20 kW
70 %
30 %
Low
10 s
3s
60 s
DE
EN
Table 3-96: Application - standard values - configure load dependent start/stop IOP
CL2
5760
{0}
IOP Reserve power

IPB Reserveleistung
{1o}
{1oc}
{2oc}
Load-dependent start stop: IOP Reserve power
0 to 999999 kW
This parameter is only effective if start stop mode (parameter 5752) is

configured to "Reserve power".
The value configured for the reserve power determines when an additional
generator will be started. The reserve power is the desired spinning reserve of a
generator or generators. The reserve power is usually estimated as the largest load
swing that a power plant may encounter during the time it takes to bring an
additional generator online. The available generator power is calculated by adding
up the generator real power ratings of all generators with closed GCBs. The reserve
generator power is calculated by subtracting the power currently being produced by
all generators with closed GCBs from the total available generator power. If the
actual reserve power of the generators is less than the value configured in this
parameter, the next generator will be started.
DE
EN
Currently available total generator rated real power

- Currently available total generator actual real power
=
Reserve power
CL2
5761
{0}
{1o}
IOP Hysteresis
IPB Hysterese
{1oc}
{2oc}
Load-dependent start stop: IOP Hysteresis
0 to 65000 kW

DE
EN
If the reserve power is sufficient to stop one genset without falling below the
threshold and the hysteresis configured here, a genset will be stopped.
CL2
5762
IOP Max. generator load

IPB Max. Generatorlast
{0}
{1o}
{1oc}
{2oc}
Load-dependent start stop: IOP Maximum generator load
0 to 100 %

configured to "Generator load".
If the generator load exceeds the threshold configured here, the load-dependent
start/stop function will start another genset.
Woodward
Page 201/339
DE
EN
Manual 37427
CL2
5763
IOP Min. generator load

IPB Min. Generatorlast
{0}
{1o}
{1oc}
{2oc}
Load-dependent start stop: IOP Minimum generator load
0 to 100 %

If the generator load falls below the threshold configured here, the load-dependent
start/stop function will stop a genset. If only a few gensets are operating in a multigenset application, the IOP Dynamic (parameter 5757 on page 203) will also be
considered when stopping a genset.
NOTE
The maximum generator load must be configured higher then the minimum generator load for proper
operation.
Page 202/339
Woodward
DE
EN
Manual 37427
CL2
5757
{0}
{1o}

IOP Dynamic
IPB Dynamik
{1oc}
{2oc}
Load-dependent start stop: IOP Dynamic

The dynamic determines when to start or stop the next genset and shows the
following behavior:
Starting a genset:
The Dynamic is only considered for the start sequence if "Fit size of engines" is
enabled (refer to parameter 5754). The control requests a certain amount of
additional load depending on the dynamic. It may start two or more gensets to
supply the required load. Also refer to the following example.
Low .............. A larger genset is requested and it will take longer until the next
change is required. The engines are operated with more reserve
power.
The requested load is calaculated so that the gensets will be loaded
with 25 % of the range between minimum and maximum generator
load (parameters 5762 & 5763) after the new genset has been started.
Moderate ..... A medium genset is requested.
High ............. A smaller genset is requested to operate the engines with higher
efficiency. This may lead to more frequent starts and stops.
Stopping a genset:
The dynamic determines how soon a genset will be stopped. It prevents continuous
start and stop if only a few gensets are in operation. In this case, the remaining
gensets would not reach the maximum limit if one genset stops (if, for example,
two gensets with 100 kW rated load, a minimum load of 40 % and a maximum
load of 70 % are operated, the second genset will be shut down if both reach 40 kW
and the remaining engine would operate with 80 kW and request the next engine
and so on). The more gensets are running, the less the influence of this parameter.
Also refer to the following example.
Low .............. The genset will shut down at a lower limit and be operated longer.
The number of gensets in operation will remain constant for a wider
range of load.
The load on the remaining gensets must not exceed 25 % of the
range between minimum and maximum generator load (parameters
5762 & 5763).
Moderate ..... The load on the remaining gensets must not exceed 50 % of the
5762 & 5763).
High ............. The genset will be shut down earlier. This may lead to more frequent
starts and stops.
5762 & 5763).
Woodward
Page 203/339
Manual 37427
Example for starting a genset:

A plant made up of several gensets with a rated power of 50, 100, and 200 kW is configured to a maximum
generator load of 70 % and a minimum generator load of 40 %. One genset with 200 kW is running and the
actual load reaches 140 kW. This is the 70 % maximum load limit of the running genset and requires the start of
the next genset.
If the dynamic is configured to Low, a total generator rated power of 294.7 kW is requested and a 100 kW
genset will be started.
If the dynamic is configured to Moderate, a total generator rated power of 254.5 kW is requested and a
100 kW genset will be started.
If the dynamic is configured to High, a total generator rated power of 224.0 kW is requested and a 50 kW
genset will be started.
Refer to Appendix G: LDSS Formulas on page 332 for details about the formulas used for calculation.
Example for stopping a genset:
Two gensets with the same rated power are configured to a maximum generator load of 70 % and a minimum
generator load of 40 %. Table 3-97 shows the load level before stopping the second genset and the resulting load
level for the first genset depending on the dynamic setting.
Dynamic
Low
Moderate
High
Load level before stopping

23.75 %
27.5 %
31.25 %
Resulting load level for remaining engine

47.5 % (25 % of the difference between 70 and 40 %)
55 % (50 % of the difference between 70 and 40 %)
62.5 % (75 % of the difference between 70 and 40 %)
DE
EN
Table 3-97: Load-dependent start/stop - dynamic influence on stopping a genset
CL2
5764
IOP Add on delay

IPB Zusetzverzgerung
{0}
{1o}
{1oc}
{2oc}
DE
EN
DE
EN
IOP Add on delay at rated load

IPB Zusetzverzg. bei Nennlast
CL2 {0} {1o} {1oc} {2oc}
5765
CL2
5766
IOP Add off delay

IPB Absetzverzgerung
{0}
{1o}
Page 204/339
{1oc}
{2oc}
Load-dependent start stop: IOP Add on delay
0 to 32000 s
Load swings may exceed the threshold momentarily. In order to prevent the engine
from starting due to short-term load swings, a delay time may be configured. The
LDSS criterion for adding load must be exceeded without interruption for this
delay time, configured in seconds, prior to a start command being issued. If the
LDSS criterion for adding load is fallen below before the delay time expires, the
delay time is reset and a start command is not issued.
Load-dependent start stop: IOP Add on delay at rated load
0 to 32000 s
The command to start the next genset in case a genset exceeds rated load will be
issued after the delay configured here has expired. This parameter becomes only
effective in case a genset exceeds rated load to achieve a faster start and overrides
parameter 5764.
Load-dependent start stop: IOP Add off delay
0 to 32000 s
Load swings may fall below the threshold momentarily. In order to prevent the
engine from stopping due to short-term load swings, a delay time may be
configured. The load must remain below the hysteresis set point without
interruption for the delay time, configured in seconds, prior to a stop command
being issued. If the load exceeds the hysteresis set point before the delay time
expires, the delay time is reset and a stop command is not issued.
Woodward
Manual 37427
Configure Application: Automatic, Load-Dependent Start/Stop: Mains Parallel Operation (MOP)

In case of a mains parallel operation (MCB closed), load-dependent start stop is only enabled, if the gensets
participates in load sharing at the interchange point (all participating gensets must be configured to the same set
point). A minimum load threshold must be exceeded to start the first genset, i.e. a genset will only be started if a
minimum load would be demanded from the generator. There are dedicated LDSS parameters for mains parallel
operation.
Parameter table
Level
Text
Setting range
Configure load dependent start/stop mains parallel operation
MOP Minimum load
0 to 65000 kW
MOP Reserve power
1 to 999999 kW
MOP Hysteresis
0 to 65000 kW
MOP Max. generator load
0 to 100 %
MOP Min. generator load
0 to 100 %
MOP Dynamic
MOP Add on delay
0 to 32000 s
MOP Add on delay at rated load
0 to 32000 s
MOP Add off delay
0 to 32000 s
Default value
10 kW
50 kW
20 kW
70 %
30 %
Low
20 s
3s
60 s
DE
EN
Table 3-98: Application - standard values - configure load dependent start/stop MOP
CL2
5767
{0}
MOP Minimum load

NPB Mindestlast
{1o}
{1oc}
{2oc}
Load-dependent start stop: MOP Minimum load
0 to 65000 kW
For the mains interchange (import/export) real power control to function, a

minimum generator power set point value is required to start the first genset. In
many cases, it is desirable that the engine is prevented from starting unless the
generator will operate at a specific kW level or higher to ensure a reasonable
degree of efficiency.
Example: The mains interchange must reach a level that will permit an 80kW
generator to operate at a minimum load of 40kW prior to the engine starting.
DE
EN
MOP Hysteresis
NPB Hysterese
CL2
5769
{0}
{1o}
{1oc}
{2oc}
Load-dependent start stop: MOP Hysteresis
0 to 65000 kW
The importance of this parameter depends on the setting of the start stop
mode (parameter 5752).
Start stop mode configured to "Reserve power": If the reserve power is sufficient to
stop one genset without falling below the reserve power threshold and the
hysteresis configured here, a genset will be stopped.
DE
EN
If the generator load falls below the minimum load threshold minus the hysteresis
configured here, the last genset will be stopped.
CL2
5768
{0}
MOP Reserve power

NPB Reserveleistung
{1o}
{1oc}
{2oc}
Load-dependent start stop: MOP Reserve power
0 to 999999 kW

The minimum reserve power in mains parallel operation is configured here. This is
the maximum expected load swing on the busbar, which shall be supported by the
gensets. If the reserve power falls below this value, the load-dependent start/stop
function will start another genset.
Woodward
Page 205/339
DE
EN
Manual 37427
CL2
5770
MOP Max. generator load

NPB Max. Generatorlast
{0}
{1o}
{1oc}
{2oc}
Load-dependent start stop: MOP Maximum generator load
0 to 100 %

DE
EN
If the generator load exceeds the threshold configured here, the load-dependent
start/stop function will start another genset.
CL2
5771
MOP Min. generator load

NPB Min. Generatorlast
{0}
{1o}
{1oc}
{2oc}
Load-dependent start stop: MOP Minimum generator load
0 to 100 %

If the generator load falls below the threshold configured here, the load-dependent
start/stop function will stop a genset. If only a few gensets are operating in a multigenset application, the MOP Dynamic (parameter 5758) will also be considered
when stopping a genset.
NOTE
The maximum generator load must be configured higher then the minimum generator load for proper
operation.
Page 206/339
Woodward
Manual 37427
EN
MOP Dynamic
NPB Dynamik
DE
CL2
5758
{0}
{1o}
{1oc}
{2oc}
Load-dependent start stop: MOP Dynamic

The dynamic determines when to start or stop the next genset and shows the
following behavior:
Starting a genset:
The Dynamic is only considered for the start sequence if "Fit size of engines" is
enabled (refer to parameter 5754). The control requests a certain amount of
additional load depending on the dynamic. It may start two or more gensets to
supply the required load.
Low .............. A larger genset is requested and it will take longer until the next
change is required. The engines are operated with more reserve
power.
Moderate ..... A medium genset is requested.
High ............. A smaller genset is requested to operate the engines with higher
efficiency. This may lead to more frequent starts and stops.
Stopping a genset:
The dynamic determines how soon a genset will be stopped. It prevents continuous
start and stop if only a few gensets are in operation. In this case, the remaining
gensets would not reach the maximum limit if one genset stops (if, for example,
two gensets with 100 kW rated load, a minimum load of 40 % and a maximum
load of 70 % are operated, the second genset will be shut down if both reach 40 kW
and the remaining engine would operate with 80 kW and request the next engine
and so on). The more gensets are running, the less the influence of this parameter.
Also refer to the following example.
Low .............. The genset will shut down at a lower limit and be operated longer.
The number of gensets in operation will remain constant for a wider
range of load.
5762 & 5763).
Moderate ..... The load on the remaining gensets must not exceed 50 % of the
5762 & 5763).
High ............. The genset will be shut down earlier. This may lead to more frequent
starts and stops.
5762 & 5763).
Refer to parameter 5757 on page 203 for examples on starting and stopping a
genset depending on the dynamic setting.
Woodward
Page 207/339
Manual 37427
EN
MOP Add on delay

NPB Zusetzverzgerung
DE
CL2
5772
{0}
{1o}
{1oc}
{2oc}
DE
EN
MOP Add on delay at rated load

NPB Zusetzverzg. bei Nennlast
{1o}
{1oc} {2oc}
CL2 {0}
5773
DE
EN
MOP Add off delay

NPB Absetzverzgerung
CL2
5774
{0}
Page 208/339
{1o}
{1oc}
{2oc}
Load-dependent start stop: MOP Add on delay
0 to 32000 s
Load swings may exceed the threshold momentarily. In order to prevent the
engine from starting due to short-term load swings, a delay time may be
configured. The LDSS criterion for adding load must be exceeded without
interruption for this delay time, configured in seconds, prior to a start command
being issued. If the LDSS criterion for adding load is fallen below before the
delay time expires, the delay time is reset and a start command is not issued.
Load-dependent start stop: MOP Add on delay at rated load
0 to 32000 s
The command to start the next genset in case a genset exceeds rated load will be
issued after the delay configured here has expired. This parameter becomes only
effective in case a genset exceeds rated load to achieve a faster start and overrides
parameter 5772.
Load-dependent start stop: MOP Add off delay
0 to 32000 s
Load swings may fall below the threshold momentarily. In order to prevent the
engine from stopping due to short-term load swings, a delay time may be
configured. The load must remain below the hysteresis set point without
interruption for the delay time, configured in seconds, prior to a stop command
being issued. If the load exceeds the hysteresis set point before the delay time
expires, the delay time is reset and a stop command is not issued.
Woodward
Manual 37427
DE
EN
Configure Application: Automatic, Start w/o Load (LogicsManager)
CL2
12540
Start w/o load

Start ohne bernahme
{0}
{1o}
---
---
{1oc}
{2oc}
Start without assuming load
LogicsManager
If this LogicsManager condition is TRUE switching from mains to generator

supply following an engine start is prevented (the GCB close operation is blocked).
This function may be used to perform a test operation. If an emergency power case
occurs meanwhile, it is still possible to change to generator operation. If this
condition becomes TRUE in isolated operation, the GCB cannot be opened before
the MCB has been closed. The LogicsManager and its default settings are
DE
EN
Configure Application: Automatic, Operation Modes
CL2
1795
Startup in mode
Einschalten in Betriebsart
{0}
{1o}
---
---
{1oc}
{2oc}
Operating mode after applying the power supply
STOP / AUTO / MAN / Last
If the controller is powered down, the unit will start in the following configured
mode when it is powered up again.
STOP ........... The unit starts in the STOP operating mode.
AUTO .......... The unit starts in the AUTOMATIC operating mode.
MAN ............ The unit starts in the MANUAL operating mode.
Last .............. The unit starts in the last operating mode the control was in prior to
being de-energized.
NOTE
DE
EN
For the selection of the operating mode via the LogicsManager (if two different operating modes have
been selected simultaneously) the control unit will prioritize the modes as follows:
1. STOP
2. MANUAL
3. AUTOMATIC
CL2
{0}
DE
CL2
{0}
DE
CL2
12530
{0}
{1oc}
{2oc}
Operat. mode MAN

Betriebsart MAN
{1o}
EN
12520
{1o}
EN
12510
Operat. mode AUTO

Betriebsart AUTO
{1oc}
{2oc}
Operat. mode STOP

Betriebsart STOP
Woodward
{1o}
{1oc}
{2oc}
Activate operating mode AUTOMATIC
LogicsManager
Once the conditions of the LogicsManager have been fulfilled the unit will change
into operating mode AUTOMATIC. If AUTOMATIC mode is selected via the
LogicsManager it is not possible to change operating modes via the front panel.
B: "LogicsManager".
Activate operating mode MANUAL
LogicsManager
into operating mode MANUAL. If MANUAL mode is selected via the
LogicsManager it is not possible to change operating modes via the front panel.
B: "LogicsManager".
Activate operating mode STOP
LogicsManager
into operating mode STOP. If STOP mode is selected via the LogicsManager it is
not possible to change operating modes via the front panel. The LogicsManager
and its default settings are explained on page 271 in Appendix B:
"LogicsManager".
Page 209/339
Manual 37427
Configure Application: Automatic, Critical Mode (Sprinkler Operation, LogicsManager)

The critical mode may be used to operate a fire engine pump or any other critical operation which does not allow
a shutdown of the genset under any alarm conditions. The LogicsManager is used to define the conditions that
will enable the critical mode like a discrete input (for conditions and explanation of programming refer to
Configure LogicsManager on page 263).
Alarm Classes
When critical mode is enabled the alarm classes are reclassified as follows:
Normal operation
Critical mode
A
A
B
B
Alarm classes
C
D
B
B
E
B
F
B
Critical mode "On"

A critical mode will be initiated/started once the critical mode operation LogicsManager output becomes TRUE
(logic "1"). The "Critical mode" message is displayed on the display screen. If the engine is not already
running, the controller will attempt to start the engine as configured (parameter 4102 on page 182). All shutdown
alarms become warning messages (see above).
Critical mode "Off"
A critical mode will be interrupted/stopped once critical mode operation LogicsManager output becomes FALSE
(logic "0") and the postrun time has expired. If the operation mode changes to STOP, this time will be considered
as expired. With termination of the critical mode, a normal cool down is performed.
NOTE
Refer to Priority Hierarchy of the Logical Outputs on page 275 for more information about the priorities
of the logical outputs.
Critical Operation (Sprinkler) Connected to the Busbar

Aforementioned fire engine pump or other critical operation is connected to the busbar, i.e. it requires a closed
GCB to be supplied by the generator during critical operation. Parameter 4100 (Close GCB in critical mode)
should be configured to "Yes" and an external provision for load reduction should be provided. This ensures the
pump operation of a sprinkler system.
Application and breaker transition mode remain as configured. A mains parallel operation is possible.
Load
MCB
GCB
Figure 3-26: Automatic - Critical operation at busbar
NOTE
The GCB will not be closed if the load is supplied by the mains until the mains fail and the MCB
remains closed because emergency run (parameter 2802) is disabled.
Critical Mode During Mains Supply

If critical mode is enabled during mains supply (MCB is closed), the generator will be started (if not already
running) and the GCB will be closed. The "Critical mode" message is displayed on the display screen. All
shutdown alarms become warning messages.
If critical mode is disabled again, all shutdown alarms become active again. If the genset was not running before
critical mode has been enabled, it will be stopped after the critical mode postrun time (parameter 4102) has
expired. MCB operation will be performed according to the configured transition mode.
Page 210/339
Woodward
Manual 37427
Emergency Power During Critical Mode

If there is a mains failure during critical mode, the "Emerg/Critical" message is displayed on the display
screen after the mains fail delay time (parameter 2800) has expired. All shutdown alarms become warning
messages.
Critical mode ends before mains recovery: The emergency power operation will be continued and all
shutdown alarms become active again. If the mains return, the unit transfers the load from generator supply to
mains supply after the mains settling delay expires.
Emergency power operation ends before the end of the critical mode: The critical mode is maintained and the
load is transferred from generator supply to mains supply after the mains settling delay expires. The engine
remains running until the conditions for the critical mode are no longer existent. If the genset was not running
before critical mode has been enabled, it will be stopped after cool down time (parameter 3316) has expired.
The GCB will take on the same state as it has before the critical mode has been enabled.
Critical Mode During Emergency Power
An emergency power operation is active (load is supplied by the generator, GCB is closed, MCB is open). If
critical mode is enabled now, the GCB remains closed and the "Emerg/Critical" message is displayed on
the display screen. All shutdown alarms become warning messages.
mains supply after the mains settling delay expires, if Enable MCB (parameter 12923) has been enabled.
load is transferred from generator supply to mains supply after the mains settling delay expires. The engine
remains running until the conditions for the critical mode are no longer existent. If the genset was not running
before critical mode has been enabled, it will be stopped after cool down time (parameter 3316) has expired.
The GCB will take on the same state as it has before the critical mode has been enabled.
Start Request During Critical Mode
The critical mode operation has priority than the remote request (Start/Stop request in AUTO). Therefore, the
remote request cannot start or stop the engine and has no effect on the breaker positions. The "Critical
mode" message is displayed on the display screen and all shutdown alarms become warning alarms.
Critical mode ends before the start request is terminated: The engine continues running. All shutdown alarms
will become active again. By resetting the start request the GCB will be opened and the engine will be
stopped.
Start request will be terminated before the critical mode is terminated: The critical mode operation is
continued. The engine keeps running until the conditions for the critical mode are no longer fulfilled and all
shutdown alarms will become active again. If the genset was not running before critical mode has been
enabled, it will be stopped after cool down time (parameter 3316) has expired. The GCB will take on the same
state as it has before the critical mode has been enabled.
Critical mode and start request: The generator is supplying load in automatic mode with closed GCB. If
critical mode is enabled, the "Critical mode" message is displayed on the display screen and all
shutdown alarms become warning alarms.
Woodward
Page 211/339
Manual 37427
Critical Operation (Sprinkler) Connected to the Generator

Aforementioned fire engine pump or other critical operation is connected to the generator, i.e. it does not require
a closed GCB to be supplied by the generator during critical operation. Parameter 4100 (Close GCB in critical
mode) should be configured to "No". This ensures an open GCB during critical mode. A closed CGB is possible
in case of an emergency operation.
Load
MCB
GCB
M
G
Figure 3-27: Automatic - Critical operation at generator
Critical Mode During Mains Supply

If critical mode is enabled during mains supply (MCB is closed), the generator will be started (if not already
running) and operated at idle speed (GCB is open). The "Critical mode" message is displayed on the display
screen. All shutdown alarms become warning messages.
If critical mode is disabled again, all shutdown alarms become active again. If the genset was not running before
critical mode has been enabled, it will be stopped after the critical mode postrun time (parameter 4102) has
expired.
Emergency Power During Critical Mode
If there is a mains failure during critical mode, the MCB will be opened after the mains fail delay time
(parameter 2800) has expired and the GCB will be closed. It is not necessary to configure parameter 4101 (Break
emerg. in critical mode) because the critical operation is already supplied. The "Emerg/Critical" message is
displayed on the display screen and all shutdown alarms become warning messages.
load is transferred from generator supply to mains supply after the mains settling delay expires. The GCB will
be opened without unloading (transition mode interchange or parallel). If open transition mode is configured,
the GCB will not be opened to prevent a dead busbar. All shutdown alarms become active again. If the genset
was not running before critical mode has been enabled, it will be stopped after cool down time
(parameter 3316) has expired.
Critical Mode During Emergency Power
An emergency power operation is active (load is supplied by the generator, GCB is closed, MCB is open). If
critical mode is enabled now, the GCB will be opened dependent on the setting of the parameter 4101 (Break
emerg. in critical mode) and a closure of the GCB is prevented for this time. The "Emerg/Critical" message
is displayed on the display screen and all shutdown alarms become warning messages.
load is transferred from generator supply to mains supply after the mains settling delay expires. The GCB will
be opened without unloading (transition mode interchange or parallel). All shutdown alarms become active
again. If the genset was not running before critical mode has been enabled, it will be stopped after cool down
time (parameter 3316) has expired.
Page 212/339
Woodward
Manual 37427
Start Request During Critical Mode

The critical mode operation has priority than the remote request (Start/Stop request in AUTO). Therefore, the
remote request cannot start or stop the engine and has no effect on the breaker positions. The "Critical
mode" message is displayed on the display screen and all shutdown alarms become warning alarms.
Critical mode ends before the start request is terminated: The engine continues running and a change to
generator or parallel operation is performed. All shutdown alarms will become active again.
enabled, it will be stopped after cool down time (parameter 3316) has expired. The GCB will take on the same
state as it has before the critical mode has been enabled.
Critical Mode During Start Request
The generator supplies the load and the GCB is closed. If critical mode is enabled, the MCB will be operated
according to the configured transition mode (parameter 3411). The GCB will be opened without unloading
(transition mode interchange or parallel). The "Critical mode" message is displayed on the display screen
and all shutdown alarms become warning alarms.
Critical mode ends before the start request is terminated: The engine continues running and a change to
generator or parallel operation is performed. All shutdown alarms will become active again.
enabled, it will be stopped after cool down time (parameter 3316) has expired.
Critical mode During Isolated Operation
The busbar is supplied by the generator and emergency run (parameter 2802) is disabled. If the critical mode is
enabled, the GCB will be opened although the MCB is not enabled. This will cause a dead busbar.
Woodward
Page 213/339
Manual 37427
Parameters
Parameter table
Level
Text
Configure critical mode
Critical mode
Critical mode postrun
Close GCB in critical mode
Critical mode alarm class MAN
Setting range
Default value
LogicsManager
0 to 6000 s
Yes / No
Yes / No
(0 & !05.08) & !09.01

600 s
No
No
Table 3-99: Application - standard values - configure critical mode
DE
EN
If this logical output becomes TRUE in AUTOMATIC operating mode, it starts the critical mode.
CL2
{0}
DE
CL2
DE
EN
4109
CL2
DE
EN
4100
CL2
4105
{1o}
EN
12220
{0}
Critical mode
Sprinklerbetrieb
{1oc}
{2oc}
Critical mode postrun

Sprinkler Nachlaufzeit
{1o}
{1oc}
{2oc}

GLS schlieen bei Sprinkler
{0}
---
{1o}
---
{1oc}
{2oc}
Override alarmcl. also in MAN

Sprinkler Alarmkl. in MAN
{0}
Page 214/339
{1o}
{1oc}
{2oc}
Critical mode request
LogicsManager
The LogicsManager and its default settings are explained on page 271 in
Appendix B: "LogicsManager".
Critical mode postrun time
0 to 6000 s
The critical mode operation is continued for the time configured here after the
critical mode request has been terminated. The message "Cool down" is
displayed and the LogicsManager command variable 04.10 becomes TRUE.
Yes / No
Yes ............... If a critical mode operation is detected the GCB will close.
No ................ The GCB cannot be closed during a critical mode operation.
Critical mode alarm classes active in MANUAL operating mode
Yes / No
Yes ............... The critical mode alarm classes will override the normal operation
alarm classes when in MANUAL operation mode and the
LogicsManager output 12220 becomes TRUE.
No ................ The alarm classes will not be changed in the MANUAL operating
mode.
Woodward
Manual 37427
Configure Application: Configure Controller

WARNING
The following parameters dictate how the easYgen-2000 Series controls voltage, frequency, load, and
power factor. It is vital that the correct setting be entered in these parameters. Failure to do so may
lead to incorrect measurements and failures within the control unit resulting in damage to or
destruction of the generator and/or personal injury or death.
Overview
The Real load, reactive load, and process control all utilize PID controllers. The response of each control loop
can be adjusted for optimum response, however it is important to understand what a PID controller is and the
effect of each controller adjustment has on the controller response. Proportional gain, integral gain (stability), and
DR (speed derivative ratio) are the adjustable and interacting parameters used to match the response of the
control loop with the response of the system. They correspond to the P (proportional), I (integral), and D
(derivative) terms, and are displayed in the easYgen as follows:
P = Proportional gain (%)
I = Integral gain (%)
D = Derivative gain (determined by DR and I)
Proportional Control
Proportional response is directly proportional to a process change. [Analogy: Setting hand throttle to keep
constant speed on straight and level.]
Proportional control (using the same analogy) results in a certain speed as long as the car is not subjected to any
load change such as a hill. If a throttle is set to any particular setting, the speed of the car will remain constant as
long as the car remains straight and level. If the car goes up a hill it will slow down. Of course, going down a hill
the car would gain speed.
Integral Control
Integral compensates for process and set point load changes. [Analogy: Cruise control maintains constant speed
regardless of hills.]
Integral, sometimes called reset, provides additional action to the original proportional response as long as the
process variable remains away from the set point. Integral is a function of the magnitude and duration of the
deviation. In this analogy the reset response would keep the car speed constant regardless of the terrain.
Derivative
Derivative provides a temporary over-correction to compensate for long transfer lags and reduce stabilization
time on process upsets (momentary disturbances). The behavior of the derivative parameter is shown in Figure
3-28 on page 216. [Analogy: Accelerating into high speed lane with merging traffic.]
Derivative, sometimes called "preact" of "rate", is very difficult to draw an accurate analogy to, because the
action takes place only when the process changes and is directly related to the speed at which the process
changes. Merging into high speed traffic of a freeway from an "on" ramp is no easy task and requires accelerated
correction (temporary overcorrection) in both increasing and decreasing directions. The application of brakes to
fall behind the car in the first continuous lane or passing gear to get ahead of the car in the first continuous lane is
a derivative action.
Woodward
Page 215/339
Manual 37427

1.00
Input dominant
Feedback dominant
Derivative operates in
relation to the actual
value
Derivative operates in
relation to the
controller output value
0.01
100.00
Figure 3-28: Controllers - Behavior of the derivative parameter
PID Tuning Example

If the system is unstable, make sure the governor is the cause. This can be checked by closing the valve limiter
until it has control of the actuator output. If the governor is causing the oscillation, time the oscillation cycle time.
A rule-of- thumb is, if the systems oscillation cycle time is less than 1 second, reduce the Proportional gain term.
A rule-of-thumb is, if the systems oscillation cycle time is greater than 1 second, reduce the Integral gain term
(proportional gain may need to be increased also).
On an initial startup with the easYgen-2000 Series, all PID dynamic gain terms will require adjustment to match
the respective PIDs response to that of its control loop. There are multiple dynamic tuning methods available
that can be used with the easYgens PIDs to assist in determining the gain terms that provide optimum control
loop response times.
The following method can be used to achieve PID gain values that are close to optimum:
1. Increase Derivative Ratio (DR) to 100.
2. Reduce integral gain to 0.01.
3. Increase proportional gain until system just starts to oscillate.
4. The optimum gain for this step is when the system just starts to oscillate and maintains a self-sustaining
oscillation that does not increase or decrease in magnitude.
5. Record the control gain (Kc) and oscillation period (T) in seconds.
6. Set the dynamics as follows:
For PI control: G=P(I/s + 1)
Set: Proportional gain = 0.45*Kc
Integral gain = 1.2/T
Derivative ratio = 100
For PID control: G=P(I/s + 1 + Ds)
Set: Proportional gain = 0.60*Kc
Integral gain = 2/T
Deriv ratio = 8/(T*Integral Gain) for feedback dominant
= (T*Integral Gain)/8 for input dominant
7. This method of tuning will get the gain settings close, they can be fine-tuned from this point.
Page 216/339
Woodward
Manual 37427
Configure Application: Controller, Frequency Control

Parameter table
Level
Text
Configure frequency control
Frequency control
Proportional gain
Integral gain
Derivative ratio
Deadband
Time pulse minimum
Gain factor
Expand deadband factor
Delay expand deadband
Frequency setpoint 1 source
Int. freq. control setpoint 1
Setpoint 2 freq.
Start frequency control level
Start frequency control delay
Freq. control setpoint ramp
Frequency control droop
Freq. droop act.
Slip frequency setpoint offset
Phase matching gain
Phase matching df-start
Freq. control initial state
Setting range
Default value
Off / PID analog / 3pos controller

0.01 to 100.00
0.01 to 100.00
0.01 to 100.00
0.02 to 9.99 Hz
0.01 to 2.00 s
0.1 to 10.0
1.0 to 9.9
1.0 to 9.9 s
Analogmanager
15.00 to 85.00 Hz
Analogmanager
15.00 to 85.00 Hz
LogicsManager
15.00 to 85.00 Hz
0 to 999 s
0.10 to 60.00 Hz/s
0.0 to 20.0 %
LogicsManager
0.00 to 0.50 Hz
1 to 99
0.02 to 0.25 Hz
0.0 to 100.0 %
PID analog
1.00
1.00
0.01
0.08 Hz
0.05 s
5.0
1.0
2.0 s
05.01
50.00 Hz
05.02
50.00 Hz
(0 & 1) & 1
47.00 Hz
5s
2.50 Hz/s
2.0 %
(08.17 & 1) & 1
0.10 Hz
5
0.05 Hz
50.0 %
DE
EN
Table 3-100: Application - standard values - configure frequency control
CL2
{0}
DE
EN
5507
Frequency Control
Frequenzregler
CL2
5510
{0}
{1o}
{1oc}
{2oc}
Proportional gain
Verstrkung
{1o}
{1oc}
{2oc}
Frequency control: activation
PID analog / 3pos controller / Off
PID analog .. The frequency is controlled using an analog PID controller.

3pos contr. ... The frequency is controlled using a three-step controller.
Off ................ Frequency control is not carried out.
Frequency control: proportional gain
0.01 to 100.00
This parameter is only visible if frequency control (parameter 5507) is

configured to "PID analog".
DE
EN
The proportional coefficient specifies the gain. By increasing the gain, the response
is increased to permit larger corrections to the variable to be controlled. The farther
out of tolerance the process is the larger the response action is to return the process
to the tolerance band. If the gain is configured too high, the result is excessive
overshoot/undershoot of the desired value.
CL2
5511
{0}
Integral gain
Integrierbeiwert
{1o}
{1oc}
{2oc}
Frequency control: integral gain
0.01 to 100.00

The integral gain identifies the I part of the PID controller. The integral gain
corrects for any offset (between set point and process variable) automatically over
time by shifting the proportioning band. Reset automatically changes the output
requirements until the process variable and the set point are the same. This
parameter permits the user to adjust how quickly the reset attempts to correct for
any offset. The integral gain constant must be greater than the derivative time
constant. If the integral gain constant is too large, the engine will continually
oscillate. If the integral gain constant is too small, the engine will take too long to
settle at a steady state.
Woodward
Page 217/339
DE
EN
Manual 37427
CL2
5512
{0}
Derivative ratio
Differenzierverhltnis
{1o}
{1oc}
{2oc}
Frequency control: derivative ratio
0.01 to 100.00

DE
EN
The derivative ratio identifies the D part of the PID controller. By increasing this
parameter, the stability of the system is increased. The controller will attempt to
slow down the action of the actuator in an attempt to prevent excessive overshoot or
undershoot. Essentially this is the brake for the process. This portion of the PID
loop operates anywhere within the range of the process unlike reset.
CL1
5550
{0}
Deadband
Unempfindlichkeit
{1o}
{1oc}
{2oc}
Frequency control: deadband
0.02 to 9.99 Hz

configured to "3pos controller".
DE
EN
Isolated operation: The generator frequency is controlled in such a manner that

the measured frequency does not deviate from the configured set point by more
than the value configured in this parameter without the controller issuing a
frequency raise/lower signal to the frequency control. This prevents unneeded wear
on the frequency bias output control or the raise/lower relay contacts.
Example: If the frequency set point is 50 Hz and a deadband of 0.5 Hz is
configured, the measured generator frequency must exceed 50.5 Hz (50 + 0.5) to
issue a lower pulse or fall below 49.5 Hz (50 - 0.5) to issue a raise pulse.
Synchronization: The generator frequency is controlled in such a manner that the
measured frequency does not deviate from the monitored reference (mains or
busbar) frequency by more than the value configured in this parameter without the
controller issuing a frequency raise/lower signal to the frequency control. This
prevents unneeded wear on the frequency bias output control or the raise/lower
relay contacts. The value configured for this parameter must be less than the value
configured for the df max (maximum frequency differential) for synchronization.
CL1
5551
Time pulse minimum

Impulsdauer Minimum
{0}
{1o}
{1oc}
{2oc}
Frequency control: time pulse minimum
0.01 to 2.00 s

DE
EN
A minimum pulse on time must be configured here. The shortest possible pulse
time should be configured to limit overshoot of the desired speed reference point.
CL1
5552
{0}
Gain factor
Verstrkungsfaktor
{1o}
{1oc}
{2oc}
Frequency control: gain factor
0.1 to 10.0

The gain factor Kp influences the operating time of the relays. By increasing the
number configured in this parameter, the operating time of the relay will be increased in response to a deviation from the frequency reference. By increasing the
gain, the response is increased to permit larger corrections to the variable to be
controlled. The farther out of tolerance the process is the larger the response action
is to return the process to the tolerance band. If the gain is configured too high, the
result is excessive overshoot/undershoot of the desired value.
Page 218/339
Woodward
Manual 37427
DE
EN

Aufweitung Unempfindlichkeit
CL1 {0} {1o} {1oc} {2oc}
5553
Frequency control: expand deadband factor
1.0 to 9.9

If the measured generator frequency is within the deadband range (parameter 5550)
and the configured delay expand deadband time (parameter 5554) expires, the
deadband will be multiplied with the factor configured here.
Kick Impulse Function

Frequency control provides a kick impulse function, which issues a pulse if the frequency control deadband
(parameter 5550) is not exceeded and no synchronization could be performed for 20 seconds. The function is
enabled, if a synchronization is carried out.
If the phase angle is between 0 and 180, a "frequency lower" signal is issued.
If the phase angle is between 180 and 360, a "frequency raise" signal is issued.
The pulse duration is 100ms. If the synchronization still fails, another pulse will be issued after 10 seconds.
DE
EN
The following conditions are required for the kick impulse function:
Frequency control (parameter 5507) is configured to "3pos controller"
Synchronization mode (parameter 5728) is configured to "RUN" or "CHECK" (or "Controlled by LM" and
RUN or CHECK enabled by the LogicsManager)
CL1
5554

Verzgerung Aufweitung
{0}
{1o}
{1oc}
{2oc}
Frequency control: delay expand deadband
1.0 to 9.9 s

The measured generator frequency must be within the deadband range for the time
configured here in order to multiply the deadband with the factor configured in
parameter 5553.
DE
EN

Frequenz Sollwert 1 Auswahl
CL2 {0} {1o} {1oc} {2oc}
5518
Frequency control: frequency setpoint 1 source
refer to text below
The Frequency setpoint 1 source may be selected from the available data sources.
Use the and softkeys to scroll through the list of variables and confirm your
selection with the softkey. Even it is possible to select all data sources (refer to
Appendix C on page 305), only the following data sources may be used (selecting a
different data source may not allow the controller to operate properly):
05.01 Internal frequency setpoint 1
Internal frequency control setpoint 1 (parameter 5500) is used as setpoint 1
05.03 Interface frequency setpoint
The setpoint, which is transmitted via the interface, is used as setpoint
05.13 Discrete raise/lower frequency
The setpoint from the discrete raise/lower frequency function is used as
setpoint
Analog input 1 is used to control the setpoint
The frequency set point may be adjusted within the configured operating limits
(refer to Configure Monitoring: Generator, Operating Voltage / Frequency on
page 48).
Woodward
Page 219/339
Manual 37427
Frequency control: internal set point 1

Frequenz Sollwert 2 Auswahl
CL2 {0} {1o} {1oc} {2oc}
5519
Frequency control: frequency setpoint 2 source
DE
EN
DE
EN

Frequenzregler Sollwert 1 int.
CL1 {0} {1o} {1oc} {2oc}
5500
15.00 to 85.00 Hz
The internal generator frequency set point 1 is defined in this screen. This value is
the reference for the frequency controller when performing isolated and/or no-load
operations. Generally 50 Hz or 60 Hz will be the values entered into this parameter.
It is possible to enter a different value here.
refer to text below
The Frequency setpoint 2 source may be selected from the available data sources.
05.03 Interface frequency setpoint
05.13 Discrete raise/lower frequency
The setpoint from the discrete raise/lower frequency function is used as
setpoint
The frequency set point may be adjusted within the operating limits (refer to
Configure Monitoring: Generator, Operating Voltage / Frequency on page 48).
DE
EN

Frequenzregler Sollwert 2 int.
CL1 {0} {1o} {1oc} {2oc}
5501
DE
EN
Setpoint 2 freq.
Freq. Sollwert 2
CL2
DE
EN
12918
CL1
5516
{0}
{1o}
{1oc}
{2oc}
Start frequency control level

Startwert
{0}
{1o}
Page 220/339
{1oc}
{2oc}
Frequency control: internal set point 2
15.00 to 85.00 Hz
The internal generator frequency set point 2 is defined in this screen. This value is
the reference for the frequency controller when performing isolated and/or no-load
operations. Generally 50 Hz or 60 Hz will be the values entered into this parameter.
It is possible that a different value may be entered here.
Frequency control: frequency set point 2 activation
LogicsManager
If this LogicsManager condition is TRUE, the frequency set point 2 will be

enabled, i.e. the setting of parameter 5519 overrides the setting of parameter 5518.
B: "LogicsManager".
Frequency control: start value
15.00 to 85.00 Hz
The frequency controller is activated when the monitored generator frequency has
exceeded the value configured in this parameter. This prevents the easYgen from
attempting to control the frequency while the engine is completing its start
sequence.
Woodward
Manual 37427
DE
EN
DE
EN
Start frequency control delay

Start Verzgerung
CL1 {0} {1o} {1oc} {2oc}
5517
CL2
DE
EN
5503
CL2
{0}
{0}
DE
CL2
12904
{1o}
{1oc}
{2oc}
Frequency control droop

Frequenzregler Statik
EN
5504
Freq. control set point ramp

Frequenzregler Rampe
{0}
{1o}
{1oc}
{2oc}
Freq. droop act.

Freq.Statik akt.
{1o}
{1oc}
{2oc}
Frequency control: start delay
0 to 999 s
The frequency controller is enabled after the configured time for this parameter
expires.
Frequency control: set point ramp
0.10 to 60.00 Hz/s
The different set point values are supplied to the controller via this ramp. The slope
of the ramp is used to alter the rate at which the controller modifies the set point
value. The faster the change in the set point is to be carried out, the greater the
value entered here must be.
Frequency control: droop
0.1 to 20.0 %
If this control is to be operated on a generator in parallel with other generators and

frequency control is enabled, a droop characteristic curve must be used. Each
generator in the system will require the same value to be configured for the droop
characteristic, so that when the system is stable the active power will be distributed
proportionally among all generators in relation to their rated power.
Frequency droop active
LogicsManager
If this LogicsManager condition is TRUE, the frequency droop is enabled. The

"LogicsManager".
NOTE
The active droop will also be sent to an ECU connected to the J1939 interface (CAN interface 2). This
information is independent from the breaker states or active controller (frequency or power controller).
Example
Rated power:
500 kW
Rated frequency set point: 50.0 Hz
Droop
5.0 %
Active power
0 kW = 0 % of rated power
Frequency is adjusted to (50.0 Hz [5.0% * 0.0 * 50 Hz]) = 50.0 Hz.
Active power
+250 kW = +50 % of rated power
Frequency is adjusted to (50.0Hz [5 % * 0.50 * 50 Hz]) = 50.0 Hz 1.25 Hz = 48.75 Hz.
DE
EN
Active power
+500 kW = +100 % of rated power
Frequency is adjusted to (50.0Hz [5 % * 1.00 * 50 Hz]) = 50.0 Hz 2.5 Hz = 47.50 Hz.
CL2
5502
Slip frequency setpoint offset

Frequenz Offset Schlupf
{0}
{1o}
{1oc}
{2oc}
Frequency control: slip frequency set point offset
0.00 to 0.50 Hz
This value is the offset for the synchronization to the busbar / utility. With this
offset, the unit synchronizes with a positive slip.
Example:
If this parameter is configured to 0.10 Hz and the busbar/mains frequency is
50.00 Hz, the synchronization set point is 50.10 Hz.
DE
EN
Phase matching gain

Nullphasen Regelg. Verstrkg.
CL2 {0} {1o} {1oc} {2oc}
5505
Woodward
Frequency control: phase matching gain
1 to 99
The phase matching gain multiplies the setting of the proportional gain
(parameter 5510 on page 217) for phase matching control.
Page 221/339
DE
EN
Manual 37427
CL2
5506
Phase matching df-start

Nullphasen Regelg. df-Start
{0}
{1o}
{1oc}
{2oc}
DE
EN
Freq. control initial state

Frequenzregler Grundstellung
CL2 {0} {1o} {1oc} {2oc}
5508
Page 222/339
Frequency control: phase matching df start
0.02 to 0.25 Hz
Phase matching will only be enabled if the frequency difference between the
systems to be synchronized is below the configured value.
Frequency control: initial state
0.0 to 100.0 %
The value entered for this parameter is the start reference point for the analog
output to the speed controller. If the output to the speed control has been disabled,
the output will act as a control position reference point.
Woodward
Manual 37427
Configure Application: Controller, Load Control

Parameter table
Level
Text
Configure load control
Load control
Proportional gain
Integral gain
Derivative ratio
Deadband
Time pulse minimum
Gain factor
Load setpoint 1 source
Load setpoint 1
Int. load control setpoint 1
Load setpoint 2
Setpoint 2 load
Load control setpoint ramp
Load control setpoint maximum
Minimum gen. import/export
Warm up load limit
Warm up time
Warm up mode
Engine warmup criterion
Warm up threshold
Setting range
Default value

0.01 to 100.00
0.01 to 100.00
0.01 to 100.00
0.10 to 9.99 %
0.01 to 2.00 s
0.1 to 10.0
1.0 to 9.9
1.0 to 9.9 s
Analogmanager
Constant / Import / Export
0.0 to 99999.9 kW
Analogmanager
Constant / Import / Export
0.0 to 99999.9 kW
LogicsManager
0.10 to 100.00 %/s
0 to 150 %
0 to 100 %
0 to 100 %
0 to 9999 s
Time controlled / Analog val contr
Analogmanager
0 to 1000 C
PID analog
1.00
1.00
0.01
1.00 %
0.05 s
5.0
1.0
2.0 s
05.04
Constant
100.0 kW
05.05
Constant
200.0 kW
(0 & 1) & 1
3.00 %/s
100 %
0%
15 %
0s
Time controlled
06.01
80 C
DE
EN
Table 3-101: Application - standard values - configure load control
CL2
{0}
DE
EN
5525
CL2
5513
{0}
Load Control
Wirkleistungsregler
{1o}
{1oc}
{2oc}
Proportional gain
Verstrkung
{1o}
{1oc}
{2oc}
Load control: activation
PID analog ... The generator load is controlled using an analog PID controller.
3pos contr. ... The generator load is controlled using a three-step controller.
Off ................ Load control is not carried out.
Load control: proportional gain
0.01 to 100.00
This parameter is only visible if load control (parameter 5525) is

The proportional coefficient specifies the gain. By increasing the gain, the
response is increased to permit larger corrections to the variable to be controlled.
The farther out of tolerance the process is the larger the response action is to
return the process to the tolerance band. If the gain is configured too high, the
DE
EN
Integral gain
Integrierbeiwert
CL2
5514
{0}
{1o}
{1oc}
{2oc}
Load control: integral gain
0.01 to 100.00

Woodward
Page 223/339
DE
EN
Manual 37427
CL2
5515
{0}
Derivative ratio
{1o}
{1oc}
{2oc}
Load control: derivative ratio
0.01 to 100.00

slow down the action of the actuator in an attempt to prevent excessive overshoot
or undershoot. Essentially this is the brake for the process. This portion of the PID
DE
EN
Deadband
Unempfindlichkeit
CL1
5560
{0}
{1o}
{1oc}
{2oc}
Load control: deadband
0.10 to 9.99 %

DE
EN
The generator load is controlled in such a manner, when paralleled with the
mains, so that the monitored load does not deviate from the configured load set
point by more than the value configured in this parameter without the controller
issuing a raise/lower signal to the speed control. This prevents unneeded wear on
the raise/lower relay contacts. The configured percentage for the dead band refers
to the generator rated active power (parameter 1752 on page 38).
CL1
5561
Time pulse minimum

Impulsdauer Minimum
{0}
{1o}
{1oc}
{2oc}
Load control: time pulse minimum
0.01 to 2.00 s

DE
EN
time should be configured to limit overshoot of the desired load reference point.
CL1
5562
{0}
Gain factor
Verstrkungsfaktor
{1o}
{1oc}
{2oc}
Load control: gain factor
0.1 to 10.0

number configured in this parameter, the operating time of the relay will be increased in response to a deviation from the power reference. By increasing the
DE
EN

CL1 {0} {1o} {1oc} {2oc}
5563
Load control: expand deadband factor
1.0 to 9.9

If the measured generator load is within the deadband range (parameter 5560) and
the configured delay expand deadband time (parameter 5564) expires, the
Page 224/339
Woodward
DE
EN
Manual 37427
CL1
5564

{0}
{1o}
{1oc}
{2oc}
Load control: delay expand deadband
1.0 to 9.9 s

DE
EN
The measured generator load must be within the deadband range for the time
parameter 5563.
CL2
5539

Wirkl. Sollwert 1 Auswahl
{0}
{1o}
{1oc}
{2oc}
Load control: load setpoint 1 source
refer to text below
The load setpoint 1 source may be selected from the available data sources. Use the
with the softkey. Even it is possible to select all data sources (refer to Appendix
C on page 305), only the following data sources may be used (selecting a different
data source may not allow the controller to operate properly):
05.04 Internal load setpoint 1
Internal load control setpoint 1 (parameter 5520) is used as setpoint 1
05.06 Interface load setpoint
05.14 Discrete raise/lower load
The setpoint from the discrete raise/lower load function is used as setpoint
The load set point may be adjusted between 0 and the configured load control
setpoint maximum (parameter 5523 on page 227).
DE
EN
Load setpoint 1
Sollwert 1
CL2
DE
EN
5526
CL1
5520
{0}
{1o}
{1oc}
{2oc}

Lstg.regler Sollwert 1 intern
{0}
Woodward
{1o}
{1oc}
{2oc}
Load control: set point 1
Import / Export / Constant
Import ......... The value entered for the import level shall always be supplied by the
utility. All load swings are absorbed by the generator(s) provided the
load rating for the generator(s) is not exceeded. The generator will
always start when an import power operation is enabled.
Export.......... The value entered for the export level shall always be supplied to the
always start when an export power operation is enabled.
Constant ...... The generator shall always supply the value entered for the constant
power level. All load swings are absorbed by the utility. The
generator will always start when a constant power (base load)
operation is enabled.
Load control: internal load control set point 1
0 to 9,999.9 kW
The load set point 1 is defined in this screen. This value is the reference for the load
controller when performing parallel operations.
Page 225/339
DE
EN
Manual 37427
CL2
5540

Wirkl. Sollwert 2 Auswahl
{0}
{1o}
{1oc}
{2oc}
Load control: load setpoint 2 source
refer to text below
The load setpoint 2 source may be selected from the available data sources. Use the
with the softkey. Even it is possible to select all data sources (refer to Appendix
C on page 305), only the following data sources may be used (selecting a different
data source may not allow the controller to operate properly):
05.06 Interface load setpoint
05.14 Discrete raise/lower load
The setpoint from the discrete raise/lower load function is used as setpoint
The load set point may be adjusted between 0 and the configured load control
setpoint maximum (parameter 5523 on page 227).
DE
EN
Load setpoint 2
Sollwert 2
CL2
DE
EN
5527
CL1
{1o}
{0}
{1o}
DE
CL2
12919
{1oc}
{2oc}

Lstg.regler Sollwert 2 intern
EN
5521
{0}
{0}
{2oc}
Setp. 2 load
Lstg.regler Soll2
{1o}
Page 226/339
{1oc}
{1oc}
{2oc}
Load control: set point 2
Import / Export / Constant
Import ..........The value entered for the import level shall always be supplied by the
always start when an import power operation is enabled.
Export ..........The value entered for the export level shall always be supplied to the
always start when an export power operation is enabled.
Constant.......The generator shall always supply the value entered for the constant
power level. All load swings are absorbed by the utility. The
generator will always start when a constant power (base load)
operation is enabled.
Load control: internal load control set point 2
0 to 9,999.9 kW
The load set point 2 is defined in this screen. This value is the reference for the load
controller when performing parallel operations.
Load control: set point 2 request
LogicsManager
If this LogicsManager condition is TRUE, the load set point 2 will be enabled, i.e.
the setting of parameter 5540 overrides the setting of parameter 5539. The
"LogicsManager".
Woodward
DE
EN
Manual 37427
CL2
5522
Load control setpoint ramp

Leistungsregler Rampe
{0}
{1o}
{1oc}
{2oc}
Load control: set point ramp
0.10 to 100.0 %/s
The different set point values are supplied to the controller via this ramp. The
slope of the ramp is used to alter the rate at which the controller modifies the set
point value. The faster the change in the set point is to be carried out, the greater
the value entered here must be.
Note: This ramp is also used in isolated operation for loading or unloading an
additional genset. An excessive oscillation may occur if the ramp is configured
too high.
DE
EN
DE
EN
Load control setpoint maximum

Leistgsregler Sollwert Maximum
{1o}
{1oc} {2oc}
CL2 {0}
5523
CL2
DE
EN
5524
CL2
{0}
{1o}
{0}
{1o}
DE
CL2
5534
{1oc}
{2oc}
Warm up load limit

Aufwrmleistungs- Limit
EN
5532
Minimum gen. import/export

Min. Gen.leistg bergabereg.
{0}
{1o}
{1oc}
{2oc}
Warm up time
Aufwrmzeit
{1oc}
{2oc}
Load control: set point maximum
0 to 150 %
If the maximum generator load is to be limited, a percentage based on the rated

generator power (parameter 1752 on page 38) must be entered here. The
controller adjusts the generator in such a manner that this value is not exceeded.
This parameter limits the set point of the load controller when the generator is in a
mains parallel operation.
Load control: minimum generator load on import/export
0 to 100 %
If the minimum generator load is to be limited, a percentage based on the rated

generator power (parameter 1752 on page 38) must be entered here. The
controller will not permit the load to drop below the configured load limit value.
This parameter is only functional when the generator is in a mains parallel
operation.
Load control: warm up load limit
0 to 100 %
The maximum load is limited to this percentage of the generator rated power
(parameter 1752 on page 38) until the warm up time (parameter 5534 on
page 227) has expired or the warm up temperature threshold (parameter 5546 on
page 228) has been exceeded.
Power control: warm up time
0 to 9999 s
This parameter is only effective if Warm up mode (parameter 5533) is

configured to "Time controlled".
The maximum load is limited to the value configured in parameter 5532 on
page 227 for the time configured here.
DE
EN
Warm up mode
Aufwrmmodus
CL2
5533
{0}
Woodward
{1o}
{1oc}
{2oc}
Load control: warm up mode
Analog val contr / Time controlled
Analog val contr .. The maximum load is limited to the value configured in
parameter 5532 until the temperature measured according to the
setting in parameter 5538 has exceeded the threshold configured in
parameter 5546.
Time controlled ... The maximum load is limited to the value configured in
parameter 5532 until the time configured in parameter 5534 has
expired.
Page 227/339
DE
EN
Manual 37427
CL2
5538
Engine warm up criterium

Teillast Warmlauf Kriterium
{0}
{1o}
{1oc}
{2oc}
Load control: warm up load criterion
refer to text below

configured to "Analog val contr".
The engine warm up criterion may be selected from the available data sources.
Appendix C on page 305), only the following data source may be used (selecting
a different data source may not allow the controller to operate properly):
DE
EN

CL2
5546
{0}
Warm up threshold
Aufwrm Grenzwert
{1o}
{1oc}
{2oc}
Load control: warm up threshold
0 to 1000 C

configured to "Analog val contr".
The maximum load is limited to the value configured in parameter 5532 until the
temperature has exceeded the threshold configured here.
Page 228/339
Woodward
Manual 37427
Configure Application: Controller, Voltage Control

Parameter table
Level
Text
Configure voltage control
Voltage control
Proportional gain
Integral gain
Derivative ratio
Deadband
Time pulse minimum
Gain factor
Voltage setpoint 1 source
Int. voltage control setpoint 1
Int. voltage control setpoint 2
Setpoint 2 voltage
Start value
Start delay
Voltage control setpoint ramp
Voltage control droop
Volt. droop act.
Voltage control initial state
Setting range
Default value

0.01 to 100.00
0.01 to 100.00
0.01 to 100.00
0.10 to 9.99 %
0.01 to 2.00 s
0.1 to 10.0
1.0 to 9.9
1.0 to 9.9 s
Analogmanager
50 to 650000 V
Analogmanager
50 to 650000 V
LogicsManager
0 to 100 %
0 to 999 s
1.00 to 300.00 %/s
0.0 to 20.0 %
LogicsManager
0.0 to 100.0 %
PID analog
1.00
1.00
0.01
1.00 %
0.05 s
5.0
1.0
2.0 s
05.07
400 V
05.08
400 V
(0 & 1) & 1
70 %
5s
5.00 %/s
5.0 %
(08.17 & 1) & 1
50.0 %
DE
EN
Table 3-102: Application - standard values - configure voltage control
CL2
{0}
DE
EN
5607
CL2
5610
{0}
Voltage Control
Spannungsregler
{1o}
{1oc}
{2oc}
Proportional gain
Verstrkung
{1o}
{1oc}
{2oc}
Voltage control: activation
PID analog .. The voltage is controlled using an analog PID controller.

3pos contr. ... The voltage is controlled using a three-step controller.
Off ................ Voltage control is not carried out.
Voltage control: proportional gain
0.01 to 100.00
This parameter is only visible if voltage control (parameter 5607) is

The proportional coefficient specifies the gain. By increasing the gain, the
response is increased to permit larger corrections to the variable to be controlled.
The farther out of tolerance the process is the larger the response action is to
return the process to the tolerance band. If the gain is configured too high, the
DE
EN
Integral gain
Integrierbeiwert
CL2
5611
{0}
{1o}
{1oc}
{2oc}
Voltage control: integral gain
0.01 to 100.00

Woodward
Page 229/339
DE
EN
Manual 37427
CL2
5612
{0}
Derivative ratio
{1o}
{1oc}
{2oc}
Voltage control: derivative ratio
0.01 to 100.00

DE
EN
slow down the action of the actuator in an attempt to prevent excessive overshoot
or undershoot. Essentially this is the brake for the process. This portion of the PID
CL1
5650
{0}
Deadband
Unempfindlichkeit
{1o}
{1oc}
{2oc}
Voltage control: deadband
0.10 to 9.99 %

DE
EN
Isolated operation: The generator voltage is controlled in such a manner that the
measured voltage does not deviate from the configured set point by more than the
value configured in this parameter without the controller issuing a voltage
raise/lower signal to the voltage regulator. This prevents unneeded wear on the
voltage bias output control or the raise/lower relay contacts.
Synchronization: The generator voltage is controlled in such a manner that the
measured voltage does not deviate from the monitored reference (mains or busbar)
voltage by more than the value configured in this parameter without the controller
issuing a voltage raise/lower signal to the voltage regulator. This prevents
unneeded wear on the voltage bias output control or the raise/lower relay contacts.
The value configured for this parameter must be less than the value configured for
the dV max (maximum voltage differential) for synchronization (parameters 5700
or 5710).
CL1
5651
Time pulse minimum

Impulsdauer Minimum
{0}
{1o}
{1oc}
{2oc}
Voltage control: time pulse minimum
0.01 to 2.00 s

DE
EN
time should be configured to limit overshoot of the desired voltage reference point.
CL1
5652
{0}
Gain factor
Verstrkungsfaktor
{1o}
{1oc}
{2oc}
Voltage control: gain factor
0.1 to 10.0

number configured in this parameter, the operating time of the relay will be increased in response to a deviation from the voltage reference. By increasing the
Page 230/339
Woodward
Manual 37427
DE
EN

CL1 {0} {1o} {1oc} {2oc}
5653
Voltage control: expand deadband factor
1.0 to 9.9

DE
EN
If the measured generator voltage is within the deadband range (parameter 5650)
and the configured delay expand deadband time (parameter 5654) expires, the
CL1
5654

{0}
{1o}
{1oc}
{2oc}
Voltage control: delay expand deadband
1.0 to 9.9 s

The measured generator voltage must be within the deadband range for the time
parameter 5653.
DE
EN

Spannungs Sollwert 1 Auswahl
CL2 {0} {1o} {1oc} {2oc}
5618
Voltage control: voltage setpoint 1 source
refer to text below
The voltage setpoint 1 source may be selected from the available data sources. Use
the and softkeys to scroll through the list of variables and confirm your
05.07 Internal voltage setpoint 1
Internal voltage control setpoint 1 (parameter 5600) is used as setpoint 1
05.09 Interface voltage setpoint
05.15 Discrete raise/lower voltage
The setpoint from the discrete raise/lower voltage function is used as setpoint
DE
EN
The voltage set point may be adjusted within the configured operating limits (refer
to Configure Monitoring: Generator, Operating Voltage / Frequency on page 48).
CL1
5600
Int.voltage control setpoint 1

Spg.regler Sollwert 1 intern
{0}
Woodward
{1o}
{1oc}
{2oc}
Voltage control: internal voltage set point 1
50 to 650,000 V
The internal generator voltage set point 1 is defined in this screen. This value is the
reference for the voltage controller when performing isolated and/or no-load
operations.
Page 231/339
Manual 37427
DE
EN

Spannungs Sollwert 2 Auswahl
CL2 {0} {1o} {1oc} {2oc}
5619
Voltage control: voltage setpoint 2 source
refer to text below
The voltage setpoint 2 source may be selected from the available data sources. Use
the and softkeys to scroll through the list of variables and confirm your
05.09 Interface voltage setpoint
05.15 Discrete raise/lower voltage
The setpoint from the discrete raise/lower voltage function is used as setpoint
DE
EN
The voltage set point may be adjusted within the configured operating limits (refer
to Configure Monitoring: Generator, Operating Voltage / Frequency on page 48).
CL1
DE
EN
5601
CL2
{0}
{1o}
{0}
{1o}
DE
CL1
5616
{1oc}
{2oc}
Setp. 2 voltage
Spannung Einstellpunkt 2
EN
12920
Int.voltage control setpoint 2

Spg.regler Sollwert 2 intern
{0}
{1o}
{1oc}
{2oc}
Start value
Startwert
{1oc}
{2oc}
Voltage control: internal voltage set point 2
50 to 650,000 V
The internal generator voltage set point 2 is defined in this screen. This value is the
reference for the voltage controller when performing isolated and/or no-load
operations.
Voltage set point 2 request
LogicsManager
If this LogicsManager condition is TRUE, the voltage set point 2 will be enabled,
i.e. the setting of parameter 5619 overrides the setting of parameter 5618. The
"LogicsManager".
Voltage control: start value
0 to 100 %
This value refers to the generator voltage set point (parameter 5600 or 5601
on page 232).
DE
EN
The voltage controller is activated when the monitored generator voltage has
exceeded the value configured in this parameter. This prevents the easYgen from
attempting to control the voltage while the engine is completing its start sequence.
CL1
5617
{0}
Start delay
Start Verzgerung
{1o}
Page 232/339
{1oc}
{2oc}
Voltage control: start delay
0 to 999 s
The voltage controller is enabled after the configured time for this parameter
expires.
Woodward
Manual 37427
DE
EN
DE
EN
Voltage control set point ramp

Spannungsregler Rampe
CL2 {0} {1o} {1oc} {2oc}
5603
CL2
{0}
DE
CL2
12905
{1o}
EN
5604
Voltage control droop

Spannungsregler Statik
{0}
{1oc}
{2oc}
Volt. droop act.

Spannungs Statik aktiv
{1o}
{1oc}
{2oc}
Example
Rated reactive power:
Rated voltage set point:
Droop
Voltage control: set point ramp
1.00 to 300.00 %/s
Voltage control: droop
0.0 to 20.0 %
If this control is to be operated on a generator in parallel with other generators and

voltage control is enabled, a droop characteristic curve must be used. Each
generator in the system will require the same value to be configured for the droop
characteristic, so that when the system is stable the reactive power will be
distributed proportionally among all generators in relation to their rated reactive
power.
Voltage droop active
LogicsManager
If this LogicsManager condition is TRUE, the voltage droop is enabled. The

"LogicsManager".
400 kvar
410 V
5.0 %
Reactive power
0 kvar = 0 % of rated power
Voltage is adjusted to (410 V [5.0% * 0.0 * 410 V]) = 410 V.
Reactive power
400 kvar = 100 % of rated reactive power
Voltage is adjusted to (410 V [5.0% * 1.0 * 410 V]) = 410 V 20.5 V = 389.5 V.
DE
EN
Voltage control initial state

Spannungsregler Grundstellung
{1o}
{1oc} {2oc}
CL2 {0}
5608
Woodward
Voltage control: initial state
0.0 to 100.0 %
The value entered for this parameter is the start reference point for the analog
output to the voltage controller. If the output to the voltage control has been
disabled, the output will act as a control position reference point.
Page 233/339
Manual 37427
Configure Application: Controller, Power Factor Control

Parameter table
Level
Text
Configure power factor control
Power factor control
Proportional gain
Integral gain
Derivative ratio
Deadband
Time pulse minimum
Gain factor
Power factor setpoint 1 source
Int. power factor setpoint 1
Power factor setpoint 2 source
Int. power factor setpoint 2
Setp. 2 pwr.factor
React. pwr. ctrl setpoint ramp
Setting range
Default value

0.01 to 100.00
0.01 to 100.00
0.01 to 100.00
0.001 to 0.300
0.01 to 2.00 s
0.1 to 10.0
1.0 to 9.9
1.0 to 9.9 s
Analogmanager
-0.710 to 1.000 to +0.710
Analogmanager
-0.710 to 1.000 to +0.710
LogicsManager
0.01 to 100.00 %/s
PID analog
1.00
1.00
0.01
0.010 %
0.05 s
5.0
1.0
2.0 s
05.10
+1.000
05.11
+1.000
(0 & 1) & 1
3.00 %/s
DE
EN
Table 3-103: Application - standard values - configure power factor control
CL2
{0}
{1o}
DE
CL2
5613
{0}
{1oc}
{2oc}
Proportional gain
Verstrkung
EN
5625
Power factor Control

Leistungsfaktor-Regler
{1o}
{1oc}
{2oc}
Power factor control: activation
PID analog ...The power factor is controlled using an analog PID controller.
3pos contr. ...The power factor is controlled using a three-step controller.
Off ................Power factor control is not carried out.
Power factor control: proportional gain
0.01 to 100.00
This parameter is only visible if power factor control (parameter 5625) is

DE
EN
The proportional coefficient specifies the gain. By increasing the gain, the response
is increased to permit larger corrections to the variable to be controlled. The farther
out of tolerance the process is the larger the response action is to return the process
to the tolerance band. If the gain is configured too high, the result is excessive
overshoot/undershoot of the desired value.
CL2
5614
{0}
Integral gain
Integrierbeiwert
{1o}
{1oc}
{2oc}
Power factor control: integral gain
0.01 to 100.00

Page 234/339
Woodward
DE
EN
Manual 37427
CL2
5615
{0}
Derivative ratio
{1o}
{1oc}
{2oc}
Power factor control: derivative ratio
0.01 to 100.00

slow down the action of the actuator in an attempt to prevent excessive overshoot or
undershoot. Essentially this is the brake for the process. This portion of the PID
DE
EN
Deadband
Unempfindlichkeit
CL1
5660
{0}
{1o}
{1oc}
{2oc}
Power factor control: deadband
0.001 to 0.300

DE
EN
The generator power factor is controlled in such a manner, when paralleled with the
mains, so that the monitored power factor does not deviate from the configured
power factor set point by more than the value configured in this parameter without
the controller issuing a raise/lower signal to the voltage regulator. This prevents
unneeded wear on the raise/lower relay contacts. The configured percentage for the
dead band refers to the generator rated reactive power (parameter 1758 on page 38).
CL1
5661
Time pulse minimum

Impulsdauer Minimum
{0}
{1o}
{1oc}
{2oc}
Power factor control: time pulse minimum
0.01 to 2.00 s

DE
EN
time should be configured to limit overshoot of the desired power factor reference
point.
CL1
5662
{0}
Gain factor
Verstrkungsfaktor
{1o}
{1oc}
{2oc}
Power factor control: gain factor
0.1 to 10.0

number configured in this parameter, the operating time of the relay will be increased in response to a deviation from the power factor reference. By increasing
the gain, the response is increased to permit larger corrections to the variable to be
DE
EN

CL1 {0} {1o} {1oc} {2oc}
5663
Power factor control: expand deadband factor
1.0 to 9.9

If the measured generator power factor is within the deadband range
(parameter 5660) and the configured delay expand deadband time
(parameter 5664) expires, the deadband will be multiplied with the factor
configured here.
Woodward
Page 235/339
DE
EN
Manual 37427
CL1
5664

{0}
{1o}
{1oc}
{2oc}
Power factor control: delay expand deadband
1.0 to 9.9 s

The measured generator power factor must be within the deadband range for the
time configured here in order to multiply the deadband with the factor configured
in parameter 5663.
DE
EN
Power Factor setpoint 1 source

Cos.phi Sollwert 1 Auswahl
CL2 {0} {1o} {1oc} {2oc}
5638
Power factor control: power factor setpoint 1 source
refer to text below
The power factor setpoint 1 source can be selected from the available data sources.
05.10 Internal power factor setpoint 1
Internal power factor control setpoint 1 (parameter 5620) is used as setpoint 1
05.12 Interface power factor setpoint
05.16 Discrete raise/lower power factor
The setpoint from the discrete raise/lower power factor function is used as
setpoint
DE
EN
The power factor set point may be adjusted between 0.71 leading and 0.71 lagging.
CL1
5620
Int: power factor setpoint 1

Cos.phi Sollwert 1 intern
{0}
{1o}
Page 236/339
{1oc}
{2oc}
Power factor control: internal power factor set point 1
-0.710 to +0.710
The desired power factor may be configured here so that the reactive power is
regulated in the system. The designations "" and "+" stand for inductive/lagging
(generator overexcited) and capacitive/leading (generator underexcited) reactive
power. This set point is active only in mains parallel operation.
Woodward
Manual 37427
DE
EN
Power Factor setpoint 2 source

Cos.phi Sollwert 2 Auswahl
CL2 {0} {1o} {1oc} {2oc}
5639
Power factor control: power factor setpoint 2 source
refer to text below
The power factor setpoint 2 source can be selected from the available data sources.
05.12 Interface power factor setpoint
05.16 Discrete raise/lower power factor
The setpoint from the discrete raise/lower power factor function is used as
setpoint
DE
EN
The power factor set point may be adjusted between 0.71 leading and 0.71 lagging.
CL1
{0}
DE
EN
5621
Int: power factor setpoint 2

Cos.phi Sollwert 2 intern
CL2
12921
{0}
{1o}
{1oc}
{2oc}
Setp. 2 pwr.factor
Cos.phi Soll 2
{1o}
{1oc}
{2oc}
DE
EN
React. pwr. ctrl setpoint ramp

Blindlstg.regler Rampe
CL2 {0} {1o} {1oc} {2oc}
5622
Power factor control: internal power factor set point 2
-0.710 to +0.710
The desired power factor may be configured here so that the reactive power is
regulated in the system. The designations "" and "+" stand for inductive/lagging
(generator overexcited) and capacitive/leading (generator underexcited) reactive
power. This set point is active only in mains parallel operation.
Reactive power set point 2 request
LogicsManager
If this LogicsManager condition is TRUE, the power factor set point 2 will be
enabled, i.e. the setting of parameter 5639 overrides the setting of parameter 5638.
B: "LogicsManager".
Power factor control: reactive power ramp
0.01 to 100.00 %/s
Note: This ramp is also used in isolated operation for loading or unloading an
additional genset. An excessive oscillation may occur if the ramp is configured too
high.
Woodward
Page 237/339
Manual 37427
Configure Application: Controller, Load Share Control

The easYgen performs proportional load and/or var sharing. This means each generator will share the load at the
same percentage level of the generator rated power when paralleled against the mains, in an isolated operation
with multiple generators paralleled, or when re-synchronizing the common bus to the mains. Proportional
load/var sharing will not be performed when the easYgen has the GCB closed and is in the constant power/base
load mode. A system can consist out of 32 gensets which are controlled by a single easYgen.
Mains parallel operation with mains interchange real power control (import/export)
The easYgen controllers maintain the real load level on the individually controlled generators at a level so that
the real power set point at the mains interchange remains at the configured set point. The real power set point for
the mains interchange must be configured identically for each easYgen.
The easYgen controller communicates with other controls in the system via a CAN bus. This enables the
controllers to adjust the real power generated by the generator while remaining within the rated power of the
generator. A smaller generator will contribute less real power as compared to a large generator, but they will both
be utilized to the same capacity factor. An example of this would be a 100 kW generator with a configured
1000 kW generator and a mains interchange of 825 kW. The 100 kW generator would contribute 75 kW and the
1000 kW generator would contribute 750 kW or both generators would be at 75% of their rated capacity.
Reactive load sharing is not performed when operating in parallel with the mains. The reactive power control will
be defined by the configured power factor set point of the individual controllers. If the power factor controller set
point is configured as +0.950, the easYgen will proportionally share the real load with all generators in parallel
with the mains while controlling the reactive power at a 0.95 inductive (lagging) power factor regardless of the
what power factor the mains is operating at.
The parameter "Active power Load share factor" (parameter 5530) can be used now to define the priority of the
real power sharing reference variable (real power at interchange). A higher configured percentage influences the
control more towards maintaining the real power set point for the interchange. A lower configured percentage
influences the control more towards maintaining real power sharing between units.
The parameter "React. power Load share factor" (parameter 5630) has no influence here.
Isolated operation in parallel
The easYgen controllers maintain the voltage and frequency of the individually controlled generators at a
constant level. This makes it imperative that the voltage and frequency set points are configured identically for
each easYgen.
The easYgen controller communicates with other controls in the system via a CAN bus. This enables the
controllers to adjust the real power generated by the generator while remaining within the rated power of the
generator. A smaller generator will contribute less real power as compared to a large generator, but they will both
be utilized to the same capacity factor. An example of this would be a 100 kW generator and a 1000 kW
generator with an 825 kW load. The 100 kW generator would contribute 75 kW and the 1000 kW generator
would contribute 750 kW or both generators would be at 75% of their rated capacity.
The reactive power will be shared proportionally among all generators involved.
The parameter "Active power Load share factor" (parameter 5530) can be used to define the priority of the
reference variable for real power sharing. A higher configured percentage influences the control more towards
frequency control. A lower configured percentage influences the control more towards real power sharing.
The parameter "React. power Load share factor" (parameter 5630) can be used now to define the priority of the
reference variable for reactive power sharing. A higher configured percentage influences the control more
towards voltage control. A lower configured percentage influences the control more towards reactive power
sharing.
Page 238/339
Woodward
Manual 37427
Re-synchronization of the busbar to the mains

The system is operating as an isolated system, for synchronization to be performed the voltage and frequency
differentials of the mains and bus must be within the configured windows.
The bus frequency reference point is dictated by the measured mains frequency and the configured frequency
differential (+ slip frequency setpoint offset (parameter 5502 on page 221)).
Example: If + slip frequency setpoint offset = 0.2 Hz, the easYgen will calculate the bus frequency reference
point as:
[measured mains frequency] + [slip frequency setpoint offset] = bus frequency reference point
A practical example of this would be:
The monitored mains frequency is 60 Hz
Configured + slip frequency setpoint offset = 0.2 Hz
[60 Hz] + [0.2Hz] = 60.2 Hz bus frequency reference point
The differential voltage is configured as a window. The monitored voltage from the potential transformers
secondary for the mains and the bus must be within the configured voltage differential limit in relation to the
rated voltage configuration.
This means that the voltage window dV [%] is in relation to the rated voltage configuration [%].
When the monitored bus frequency and voltage are within the configured differential limits, the "Command:
close MCB" relay will enable, closing the MCB, and the system will be paralleled to the mains.
Prerequisites
All easYgen controllers connected to the system must have rated system frequencies and breaker logic configured
identically and the parameter "Active power load share" (parameter 5531) or "Reactive power load share"
(parameter 5631) must be enabled.
Description of the load-share interface
The easYgen utilizes a peer relationship between units to control the system. This permits for parallel
applications of up to 16 generators.
NOTE
Refer to the Interface section of the Installation Manual 37426 for information about the CAN bus
connection.
Diagram of load/var sharing via the CAN bus

Refer to Figure 3-29 on page 240 for this diagram. The parameter "Active load sharing factor" determines if and
how a generator performs real power or frequency control when paralleled with other generators in an isolated
operation. This parameter is defined as a percentage. In the figure below 10 % means increased real power
control and 99 % increased frequency control. This parameter must be configured individually for each generator.
In the illustrated control system, it must be noted that each control calculates the mean utilization factor of all
controls from the data transmitted via the CAN bus and then compares this with its own utilization factor. The
utilization factor is compared with the reference variable and results in a new reference variable set point.
Frequency and real power control are carried out simultaneously in these controls (corresponding to the reference
variable).
Frequency control is carried out via the measured voltage/frequency of the voltage system. The MPU is used
merely for monitoring functions, or is available as a control value to the secondary controller.
Woodward
Page 239/339
Manual 37427
Figure 3-29: CAN bus load/var sharing, diagram
Page 240/339
Woodward
Manual 37427
Parameter table
Level
Text
Configure load share
Active power load share
Active power load share factor
Reactive power load share
React. power load share factor
Segment number
Segment no.2 act
Mode ext. load share interface
Setting range
Default value
On / Off
10 to 99 %
On / Off
10 to 99 %
1 to 32
LogicsManager
0 to 16
On
50 %
On
50 %
1
(0 & 1) & 1
0
DE
EN
Table 3-104: Application - standard values - configure load share
CL2
5531
Active power load share

Wirkleistungsverteilung
{0}
{1o}
{1oc}
{2oc}
DE
EN
Active power load share factor

Wirkl.verteilg. Fhrungsgr.
CL2 {0} {1o} {1oc} {2oc}
5530
Load share control: active power LS activation
On / Off
On .................Active power load share is enabled. When multiple generators are

operating in parallel, the real power is shared proportionally.
Off ................Active power load share is disabled
Load share control: active power load share factor
10 to 99 %
It is possible to change the emphasis placed on maintaining control variables. By

increasing or decreasing the percentage value in this parameter, the control places
a higher priority on maintaining the primary or secondary control reference
variable. If the value for this parameter is configured higher, maintaining the
primary control variable has a higher priority. If the value for this parameter is
configured lower, maintaining the secondary control variable has a higher priority.
Primary control variable
Isolated operation = frequency maintained
Mains parallel operation = real power level at the mains interchange point
maintained
Secondary control variable
Isolated operation = real power sharing with other generators maintained
Mains parallel operation = real power sharing with other generators maintained
DE
EN
The smaller this factor the higher the priority to equally share the load among all
generators.
If 99 % is configured here, only the primary control reference variable is
considered. If 10 % is configured here, only the secondary control reference
variable is considered.
CL2
5631
Reactive power load share

Blindleistungsverteilung
{0}
Woodward
{1o}
{1oc}
{2oc}
Load share control: reactive power LS activation
On / Off
On .................Reactive power load share is enabled. When multiple generators are

operating in parallel, the reactive power is shared proportionally.
Off ................Reactive power load share is disabled
Page 241/339
Manual 37427
DE
EN
React. power load share factor

Blindl.verteilg. Fhrungsgr.
CL2 {0} {1o} {1oc} {2oc}
5630
Load share control: reactive power load share factor
10 to 99 %
It is possible to change the emphasis placed on maintaining control variables. By

increasing or decreasing the percentage value in this parameter, the control places
a higher priority on maintaining the primary or secondary control reference
variable. If the value for this parameter is configured higher, maintaining the
primary control variable has a higher priority. If the value for this parameter is
configured lower, maintaining the secondary control variable has a higher priority.
Primary control variable
Isolated operation = voltage maintained
Secondary control variable
Isolated operation = reactive power sharing with other generators maintained
The smaller this factor the higher the priority to equally share the load among all
generators.
If 99 % is configured here, only the primary control reference variable is
considered. If 10 % is configured here, only the secondary control reference
variable is considered.
Page 242/339
Woodward
Manual 37427
Configure Application: Controller, Load Share Control, Grouping

Load sharing with several gensets is possible for a supply of a maximum of four split busbars. A group breakers
splits the busbar in a way that some gensets supply one busbar and some supply another one. However, it is
necessary to group the gensets, which supply the same busbar, into segments.
The configured segment number can be changed to one of three alternative segment numbers. The
LogicsManager is used to realize this.
Example:
Six gensets (G1 through G6) supply a system with two group breakers (A, B) as shown in Figure 3-30. All
gensets have the same segment number configured #1 (parameter 1723)
Case I: Group breakers A and B are closed and G1 through G6 supply the same busbar.
The same segment number is configured to each genset since all gensets supply the same busbar.
Case II: Group breaker A is closed and group breaker B is open (G1 through G4 supply a different busbar than
G5 and G6).
A different segment number must be selected for G5 and G6 by enabling the LogicsManager function
"Segment no.2 act" (parameter 12929) in order to change the segment number of G5 and G6 to #2.
A
G1
G3
G2
G2
G6
2
B
A
G1
G5
G4
II
G3
G4
G5
G6
Figure 3-30: Load sharing - grouping
Woodward
Page 243/339
Manual 37427
EN
Segment number
Segmentnummer
DE
CL2
{0}
{1o}
DE
EN
1723
CL2
12929
{0}
{1oc}
{2oc}
Segment no.2 act

Segmentnr.2 aktiv
{1o}
{1oc}
{2oc}
DE
EN
Mode ext. load share interface

Modus Ext. Verteilungsmodul
CL2 {0} {1o} {1oc} {2oc}
5568
Load share control: segment number
1 to 32
The genset is assigned a load share segment number with this parameter. This
segment number may be overridden by the following parameter 12929.
Load share control: segment number 2 active
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, this genset is
assigned load share segment number 2. The LogicsManager and its default
Load share control: Mode for external load share interface
0 to 16
The operation mode for the external Woodward LSI load share interface is
configured here.
0.................... External load share interface is disabled
1.................... External load share interface is enabled for Woodward EGCP-2 or
GCP-1 connectivity
2.................... External load share interface is enabled for Woodward SPM-D
connectivity
3.................... External load share interface is enabled for Woodward 2301 A
connectivity
4.................... External load share interface is enabled for Caterpillar LSM 9907252 connectivity
5.................... External load share interface is enabled for Caterpillar LSM 9907173 1 connectivity
6.................... External load share interface is enabled for Barber Colman POW-RCON connectivity
7 to 16 .......... External load share interface is disabled (reserved settings)
Page 244/339
Woodward
Manual 37427
Configure Application: Controller, Discrete Raise/Low/Function

The frequency / load and voltage / reactive power set points may be raised and lowered using the LogicsManager
functionality, i.e. it is possible to use LogicsManager command variables to raise and lower these set points.
Most commonly a button may be used to energize a discrete input on the control, which is used again as a
LogicsManager command variable to enable the respective LogicsManager function to change the set point.
The discrete raise/lower function always uses the actual value at the time when this function is enabled for the
respective controller set point as initial value. If the actual value is negative at this point in time, the initial value
is zero.
Frequency and voltage may be adjusted within the configured operating limits (refer to Configure Monitoring:
Generator, Operating Voltage / Frequency on page 48). Active power may be adjusted between 0 and the
configured load control setpoint maximum (parameter 5523 on page 227). The power factor may be adjusted
between 0.71 leading and 0.71 lagging.
Parameter table
Level
Text
Configure discrete raise/lower function
Discrete f/P +
Discrete f/P Discrete V/PF +
Discrete V/PF -
Setting range
Default value
LogicsManager
LogicsManager
LogicsManager
LogicsManager
(0 & 1) & 1
(0 & 1) & 1
(0 & 1) & 1
(0 & 1) & 1
DE
EN
Table 3-105: Application - standard values - configure discrete raise/lower function
CL2
{0}
{1o}
DE
EN
12900
CL2
{0}
{1o}
DE
CL2
{0}
{1o}
DE
EN
12902
CL2
12903
{0}
Woodward
{1oc}
{2oc}
Discrete f/P Sollwert f/P {1oc}
{2oc}
Discrete V/PF +
Sollwert U/Q +
EN
12901
Discrete f/P +
Sollwert f/P +
{1o}
{1oc}
{2oc}
Discrete V/PF Sollwert U/Q {1oc}
{2oc}
Setpoints digital poti: raise f/P set point
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the frequency /
load set point will be raised. The LogicsManager and its default settings are
Setpoints digital poti: lower f/P set point
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the frequency /
load set point will be lowered. The LogicsManager and its default settings are
Setpoints digital poti: raise V/Q set point
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the voltage /
reactive power set point will be raised. The LogicsManager and its default settings
Setpoints digital poti: lower V/Q set point
LogicsManager
Once the conditions of the LogicsManager have been fulfilled, the voltage /
reactive power set point will be lowered. The LogicsManager and its default
Page 245/339
Manual 37427
Configure Interfaces
NOTE
Please refer to the Interface Manual 37430 for a detailed description of the interface parameters.
Configure Interfaces: Configure CAN Interfaces (FlexCAN)

NOTE
The CAN bus is a field bus and subject to various disturbances. Therefore, it cannot be guaranteed that
every request will be answered. We recommend to repeat a request, which is not answered within
reasonable time.
Configure CAN Interface 1

Parameter table
Level
Text
Configure CAN interface 1
Baudrate
Node-ID CAN-Bus 1
CANopen Master
Producer heartbeat time
COB ID SYNC Message
Producer SYNC Message time
COB ID TIME Message
Setting range
Default value
20 / 50 / 100 / 125 / 250 / 500 /

800 / 1000 kBd
1 to 127 (dec)
Default Master / On / Off
0 to 65500 ms
1 to FFFFFFFF hex
0 to 65500 ms
1 to FFFFFFFF hex
250 kBd
1
Default Master
2000 ms
80 hex
20 ms
100 hex
DE
EN
Table 3-106: Application - standard values - configure CAN interface 1
CL2
{0}
DE
EN
3156
CL2
8950
{0}
{1o}
Baudrate
Baudrate
{1oc}
{2oc}
Node-ID CAN-Bus 1
Node-ID CAN-Bus 1
{1o}
{1oc}
{2oc}
CAN bus 1: Baud rate
20 / 50 / 100 / 125 / 250 / 500 / 800 / 1,000 kBaud
This parameter defines the used Baud rate. Please note, that all participants on the
CAN bus must use the same Baud rate.
CAN bus 1: Node ID
1 to 127 (dec)
A number that is unique to the control must be set in this parameter so that this
control unit can be correctly identified on the CAN bus. This address number may
only be used once on the CAN bus. All additional addresses are calculated based
on this unique device number.
NOTE
We recommend to configure the Node-IDs for units, which participate in load sharing, as low as
possible to facilitate establishing of communication.
Page 246/339
Woodward
DE
EN
Manual 37427
CL2
8993
{0}

CANopen Master
CANopen Master
{1o}
{1oc}
{2oc}
CAN bus 1: CANopen Master
Default Master / On / Off
One bus participant must take over the network management and put the other
participants into "operational" mode. The easYgen is able to perform this task.
Default Master The unit starts up in "operational" mode and sends a
"Start_Remote_node" message after a short delay (the delay is the
Node ID (parameter 8950) in seconds, i.e. if the Node ID is
configured to 2, the message will be sent after 2 seconds). If more
than one easYgen is configured to Default Master, the unit with the
lower Node ID will take over control. Therefore, the CAN bus
devices, which are intended to act as Default Master should be
assigned a low Node ID. No other device on the CAN bus (except
the easYgens) may operate as Master).
On ................ The unit is the CANopen Master and automatically changes into
operational mode and transmits data.
Off ................ The unit is a CANopen Slave. An external Master must change into
operational mode.
NOTE
DE
EN
If CANopen Master (parameter 8993) is configured to "Off", the Master controller (for example a PLC)
must send a "Start_Remote_node" message to initiate the load share message transmission of the
easYgen.
If no "Start_Remote_node" message would be sent, the complete system would not be operational.
CL2
DE
EN
9120
CL2
9100

{0}
{1o}
{1oc}
{2oc}
COB ID SYNC Message

COB ID SYNC Message
{0}
{1o}
{1oc}
{2oc}
CAN bus 1: Producer heartbeat time
0 to 65500 ms
Independent from the CANopen Master configuration, the unit transmits a

heartbeat message with this configured heartbeat cycle time. If the producer
heartbeat time is equal 0, the heartbeat will only be sent as response to a remote
frame request. The time configured here will be rounded up to the next 20 ms step.
CAN bus 1: COB ID SYNC Message
1 to FFFFFFFF hex
This parameter defines whether the unit generates the SYNC message or not.
Complies with CANopen specification: object 1005, subindex 0; defines the COB ID of the
synchronization object (SYNC). The structure of this object is shown in the following tables:
32
MSB
bits bits
31
30 29
11 bit ID 11 bit ID X
0/1 X
UNSIGNED
bit number
31 (MSB)
30
29
28-11
10-0 (LSB)
DE
EN

{1o}
{1oc} {2oc}
CL2 {0}
8940
Woodward
value
X
0
1
X
0
X
CAN bus 1: Sending time for SYNC Message
28-11
000000000000000000
LSB
10-0
11 bit identifier
meaning
N/A
Unit does not generate SYNC message
Unit generates SYNC message
N/A
always
bits 10-0 of SYNC COB ID
0 to 65000 ms
This is the cycle time of the SYNC message. If the unit is configured for this
function (parameter 9100) it will send the SYNC message with this interval. The
time configured here will be rounded up to the next 10 ms step.
Page 247/339
DE
EN
Manual 37427
CL2
9101
COB-ID TIME Message

COB-ID TIME Message
{0}
{1o}
{1oc}
{2oc}
CAN bus 1: COB ID TIME Message
1 to FFFFFFFF hex
This parameter defines whether the unit generates the TIME message or not.
Complies with CANopen specification: object 1012, subindex 0; defines the COB ID of the time object
(TIME). The structure of this object is shown in the following tables:
32
MSB
bits bits
31
30 29
11 bit ID 11 bit ID X
0/1 X
UNSIGNED
bit number
31 (MSB)
30
29
28-11
10-0 (LSB)
Page 248/339
value
X
0
1
X
0
X
28-11
000000000000000000
LSB
10-0
11 bit identifier
meaning
N/A
Unit does not generate TIME message
Unit generates TIME message
N/A
always
bits 10-0 of TIME COB ID
Woodward
Manual 37427
Additional Server SDOs (Service Data Objects)
NOTE
The CAN bus is a field bus and subject to various disturbances. Therefore, it cannot be guaranteed that
every request will be answered. We recommend to repeat a request, which is not answered within
reasonable time.
NOTE
The first Node ID is the standard Node ID of CAN interface 1 (parameter 8950).
Parameter table
Level
Text
Configure CAN interface 1: additional Server SDOs
2. Node ID
3. Node ID
4. Node ID
5. Node ID
Setting range
Default value
0 to 127 (dec)
0 to 127 (dec)
0 to 127 (dec)
0 to 127 (dec)
0
0
0
0
DE
EN
Table 3-107: Application - standard values - configure CAN interface 1: additional Server SDOs
CL2
{0}
{1o}
DE
EN
33040
CL2
{0}
{1o}
DE
EN
33041
CL2
{0}
{1o}
DE
EN
33042
CL2
33043
{0}
Woodward
{1o}
2. Node ID
2. Node-ID
{1oc}
{2oc}
3. Node ID
3. Node-ID
{1oc}
{2oc}
4. Node ID
4. Node-ID
{1oc}
{2oc}
5. Node ID
5. Node-ID
{1oc}
{2oc}
CAN bus 1: Additional Server SDOs - 2. Node ID
0 to 127 (dec)
In a multi-master application, each Master needs its own identifier (Node ID) from
the unit. in order to send remote signals (i.e. remote start, stop, or acknowledge) to
the unit. The additional SDO channel will be made available by configuring this
Node ID to a value different than zero. This is the additional CAN ID for the PLC.
0 to 127 (dec)
0 to 127 (dec)
0 to 127 (dec)
Page 249/339
Manual 37427
Receive PDO {x} (Process Data Object) [x = 1 to 5]

Figure 3-31 shows the principle of PDO mapping.
Object Dictionary
xxxxh Application Object 1
PDO Mapping
0
3
1 yyyyh 1
2 zzzzh 1
3 xxxxh 1
yyyyh Application Object 2

zzzzh Application Object 3
PDO: App. Object 2 Application Object 3 App. Object 1

Figure 3-31: Interfaces - Principle of PDO mapping
Parameter table
Level
Text
Configure CAN interface 1: receive PDOs
COB-ID
Event-timer
Selected data protocol
Number of Mapped Objects
1. Mapped Object
2. Mapped Object
3. Mapped Object
4. Mapped Object
Setting range
Default value
1 to FFFFFFFF hex
0 to 65500 ms
0 to 65535
0 to 4
0 to 65535
0 to 65535
0 to 65535
0 to 65535
80000000 hex
2000 ms
0
0
0
0
0
0
DE
EN
Table 3-108: Application - standard values - configure CAN interface 1: receive PDOs
CL2
9300
9310
9320
{0}
{1o}
COB-ID
COB-ID
{1oc}
{2oc}
CAN bus 1: Receive PDO {x} - COB ID
1 to FFFFFFFF hex
This parameter contains the communication parameters for the PDOs, the device is
able to receive.
Complies with CANopen specification: object 1400 (for RPDO 1, 1401 for RPDO 2 and 1402 for
TPDO 3), subindex 1. The structure of this object is shown in the following tables:
32 MSB
bits 31
30
11 bit ID 0/1
X
UNSIGNED
bit number
31 (MSB)
30
29
28-11
10-0 (LSB)
29
X
value
0
1
X
X
0
X
28-11
000000000000000000
LSB
10-0
11 bit identifier
meaning
PDO exists / is valid
PDO does not exist / is not valid
N/A
N/A
always
bits 10-0 of COB ID
PDO valid / not valid allows to select, which PDOs are used in the operational state.
NOTE
Do not configure an RPDO or TPDO with a COB-ID higher than 580 (hex) or lower than 180 (hex). These
IDs are reserved for internal purposes.
Page 250/339
Woodward
DE
EN
Manual 37427
CL2
9121
9122
9123
{0}
{1o}

Event-timer
Event-timer
{1oc}
{2oc}
CAN bus 1: Receive PDO {x} - Event timer
0 to 65500 ms
This parameter configures the time, from which this PDO is marked as "not
existing". The time configured here will be rounded up to the next 5 ms step.
Received messages are processed by the control unit every 20 ms. Messages, which
are sent faster, will be discarded. We recommend to configure ten times the cycle
time of the received data here.
Complies with CANopen specification: object 1400 (for TPDO 1, 1401 for TPDO 2 and 1402 for
TPDO 3), subindex 5
CAN bus 1: Receive PDO {x} - Selected data protocol

Anzahl der Mapped Objekte
CL2 {0} {1o} {1oc} {2oc}
9910
CAN bus 1: Receive PDO {x} - Number of mapped objects
DE
EN
Selected Data Protocol

Ausgewhltes Datenprotocoll
CL2 {0} {1o} {1oc} {2oc}
8970
DE
EN
8971
8972
9915
9905
0 to 65535
A data protocol may be selected by entering the data protocol ID here. If 0 is

configured here, the message assembled by the mapping parameters is used. If an
unknown data protocol ID is configured here, a failure is indicated by the CAN
status bits. Possible data protocol IDs are:
65000: IKD 1 external DIs/DOs 1 through 8
0 to 4
This parameter defines the number of valid entries within the mapping record. This
number is also the number of the application variables, which shall be received with
the corresponding PDO.
DE
EN
RPDO 3), subindex 0
CL2
9911
9916
9906
{0}
1. Mapped Object
1. Mapped Objekt
{1o}
{1oc}
{2oc}
CAN bus 1: Receive PDO {x} - 1. mapped object
0 to 65535
This parameter contains the information about the mapped application variables.
These entries describe the PDO contents by their index. The sub-index is always 1.
The length is determined automatically.
DE
EN
RPDO 3), subindex 1
CL2
9912
9917
9907
{0}
2. Mapped Object
2. Mapped Objekt
{1o}
{1oc}
{2oc}
0 to 65535
DE
EN
RPDO 3), subindex 2
CL2
9913
9918
9908
{0}
3. Mapped Object
3. Mapped Objekt
{1o}
{1oc}
{2oc}
0 to 65535
RPDO 3), subindex 3
Woodward
Page 251/339
DE
EN
Manual 37427
CL2
9914
9919
9909
{0}
4. Mapped Object
4. Mapped Objekt
{1o}
{1oc}
{2oc}
0 to 65535
RPDO 3), subindex 4
Transmit PDO {x} (Process Data Objects) [x = 1 to 5]

Parameter table
Level
Text
Configure CAN interface 1: transmit PDOs
COB-ID
Transmission type
Event-timer
Selected data protocol
1. Mapped Object
2. Mapped Object
3. Mapped Object
4. Mapped Object
Setting range
Default value
1 to FFFFFFFF hex
0 to 255
0 to 65500 ms
0 to 65535
0 to 4
0 to 65535
0 to 65535
0 to 65535
0 to 65535
80000000 hex
255
20 ms
0
0
0
0
0
0
DE
EN
Table 3-109: Application - standard values - configure CAN interface 1: transmit PDOs
CL2
9600
9610
9620
{0}
{1o}
COB-ID
COB-ID
{1oc}
{2oc}
CAN bus 1: Transmit PDO {x} - COB ID
1 to FFFFFFFF hex
This parameter contains the communication parameters for the PDOs the unit is
able to transmit. The unit transmits data (i.e. visualization data) on the CAN ID
configured here.
Complies with CANopen specification: object 1800 for (TPDO 1, 1801 for TPDO 2 and 1802 for
TPDO 3), subindex 1. The structure of this object is shown in the following tables:
32
MSB
bits bits
31
30
11 bit ID 11 bit ID 0/1
X
UNSIGNED
bit number
31 (MSB)
30
29
28-11
10-0 (LSB)
29
X
value
0
1
X
X
0
X
28-11
000000000000000000
LSB
10-0
11 bit identifier
meaning
PDO exists / is valid
PDO does not exist / is not valid
N/A
N/A
always
bits 10-0 of COB ID
PDO valid / not valid allows to select, which PDOs are used in the operational state.
NOTE
Do not configure an RPDO or TPDO with a COB-ID higher than 580 (hex) or lower than 180 (hex). These
IDs are reserved for internal purposes.
Page 252/339
Woodward
DE
EN
Manual 37427
CL2
9602
9612
9622
{0}
Transmission type
Transmission type
{1o}
{1oc}
{2oc}
CAN bus 1: Transmit PDO {x} - Transmission type
0 to 255
able to transmit. It defines whether the unit broadcasts all data automatically (value
254 or 255) or only upon request with the configured address of the COB ID SYNC
message (parameter 9100).
TPDO 3), subindex 2. The description of the transmission type is shown in the following table:
transmission type
0
1-240
241-251
252
253
254
255
PDO transmission
cyclic acyclic synchronous
will not be sent
X
X
will not be sent
will not be sent
will not be sent
asynchronous
RTR only
X
X
DE
EN
A value between 1 and 240 means that the PDO is transferred synchronously and cyclically. The
transmission type indicating the number of SYNC, which are necessary to trigger PDO transmissions.
Receive PDOs are always triggered by the following SYNC upon reception of data independent of the
transmission types 0 to 240. For TPDOs, transmission type 254 and 255 means, the application event is
the event timer.
CL2
9604
9614
9624
{0}
{1o}
Event timer
Event-timer
{1oc}
{2oc}
CAN bus 1: Transmit PDO {x} - Event timer
0 to 65500 ms
able to transmit. The broadcast cycle for the transmitted data is configured here.
The time configured here will be rounded up to the next 5 ms step.
TPDO 3), subindex 5
CAN bus 1: Transmit PDO {x} - Selected data protocol

Anzahl der Mapped Objekte
CL2 {0} {1o} {1oc} {2oc}
9609
CAN bus 1: Transmit PDO {x} - Number of mapped objects
DE
EN
Selected Data Protocol

Ausgewhltes Datenprotocoll
CL2 {0} {1o} {1oc} {2oc}
8962
DE
EN
8963
8964
9619
9629
0 to 65535
A data protocol may be selected by entering the data protocol ID here. If 0 is

configured here, the message assembled by the mapping parameters is used. If an
unknown data protocol ID is configured here, a failure is indicated by the CAN
status bits. Possible data protocol IDs are:
5100: Data telegram
5101: Data telegram
5102: Data telegram
0 to 4
This parameter contains the mapping for the PDOs the unit is able to transmit. This
number is also the number of the application variables, which shall be transmitted
with the corresponding PDO.
Complies with CANopen specification: object 1A00 (for TPDO 1, 1A01 for TPDO 2 and 1A02 for
TPDO 3), subindex 0
Woodward
Page 253/339
DE
EN
Manual 37427
CL2
9605
9615
9625
{0}
1. Mapped Object
1. Mapped Objekt
{1o}
{1oc}
{2oc}
CAN bus 1: Transmit PDO {x} - 1. mapped object
0 to 65535
DE
EN
TPDO 3), subindex 1
CL2
9606
9616
9626
{0}
2. Mapped Object
2. Mapped Objekt
{1o}
{1oc}
{2oc}
0 to 65535
DE
EN
TPDO 3), subindex 2
CL2
9607
9617
9627
{0}
3. Mapped Object
3. Mapped Objekt
{1o}
{1oc}
{2oc}
0 to 65535
DE
EN
TPDO 3), subindex 3
CL2
9608
9618
9628
{0}
4. Mapped Object
4. Mapped Objekt
{1o}
{1oc}
{2oc}
0 to 65535
TPDO 3), subindex 4
NOTE
CANopen allows to send 8 byte of data with each Transmit PDO. These may be defined separately if no
pre-defined data protocol is used.
All data protocol parameters with a parameter ID may be sent as an object with a CANopen Transmit
PDO.
In this case, the data length will be taken from the data byte column (refer to the Data Protocols section
in the Interface Manual 37430):
1,2 UNSIGNED16 or SIGNED16
1,2,3,4
UNSIGNED32 or SIGNED32
3,4,5,6
UNSIGNED32 or SIGNED32
etc.
The object ID is identical with the parameter ID when configuring via front panel or ToolKit.
Page 254/339
Woodward
Manual 37427
Configure CAN Interface 2

Parameter table
Level
Text
Configure CAN interface 2
Baudrate
Setting range
Default value
20 / 50 / 100 / 125 / 250 kBd
250 kBd
Table 3-110: Application - standard values - configure CAN interface 2
DE
EN
Baudrate
Baudrate
CL2
3157
{0}
{1o}
{1oc}
{2oc}
CAN bus 2: Baud rate
20 / 50 / 100 / 125 / 250 kBaud
This parameter defines the used Baud rate. Please note, that all participants on the
CAN bus must use the same Baud rate.
CANopen Interface
Parameter table
Level
Text
Configure CAN interface 2: CANopen
This device
IKD1 DI/DO 1..8
IKD1 DI/DO 9..16
IKD1 DI/DO 17..24
IKD1 DI/DO 25..32
Phoenix DI/DO 1..16
Phoenix DI/DO 17..32
Phoenix DI/DO 1..32
Phoenix 12 AI 4AO
Phoenix 16AI 4AO
Phoenix 16AI 4AO DI/DO 1..32
RemoteDisplay
Configure external devices
Setting range
Default value
Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
Yes / No
Node-ID 7
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
No
DE
EN
Table 3-111: Application - standard values - configure CAN interface 2: CANopen
CL2
{0}
DE
EN
9940
CL2
{0}
DE
EN
9930
CL2
9931
{0}
Woodward
{1o}
This device
Dieses Gert
{1oc}
{2oc}
IKD1 DI/DO 1..8

IKD1 DI/DO 1..8
{1o}
{1oc}
{2oc}
IKD1 DI/DO 9..16

IKD1 DI/DO 9..16
{1o}
{1oc}
{2oc}
CAN bus 2: Node ID for this device
Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
The Node ID for the control unit (this device ) is configured here.
CAN bus 2: Node ID for IKD 1 DI/DO 1-8
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
The unit is pre-configured for the connection of a Woodward IKD 1 expansion

board with the discrete inputs/outputs 1 through 8 by configuring a Node ID here.
CAN bus 2: Node ID for IKD 1 DI/DO 9-16
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
The unit is pre-configured for the connection of a Woodward IKD 1 expansion

board with the discrete inputs/outputs 9 through 16 by configuring a Node ID here.
Page 255/339
DE
EN
Manual 37427
CL2
DE
EN
9934
CL2
15134
{0}
Phoenix DI/DO 1..16

Phoenix DI/DO 1..16
{1o}
{1oc}
{2oc}
Configure external devices

Externe Gerte konfigurieren
{0}
{1o}
{1oc}
{2oc}
CAN bus 2: Node ID for Phoenix DI/DO 1-16
Off / Node-ID 1 / 2 / 3 / 4 / 5 / 6 / 7
The unit is pre-configured for the connection of a Phoenix Contact expansion board
with the discrete inputs/outputs 1 through 16 by configuring a Node ID here.
CAN bus 2: Configure external devices
Yes / No
This parameter starts the configuration of external Phoenix expansion boards.

Proceed as follows to configure an external device:
Connect external device
Configure parameters at the easYgen (Node ID, DI/Os, AI/Os)
Set this parameter to Yes
Verify the successful configuration of the external device
Note: This parameter can only be used to configure a Phoenix expansion board.
Refer to the IKD 1 manual 37135 for configuring the IKD 1 expansion boards.
Page 256/339
Woodward
Manual 37427
J1939 Interface
Parameter table
Level
Text
Configure CAN interface 2: J1939
J1939 device addresses
Engine control address
Reset previous act. DTCs - DM3
Reset act. DTCs - DM3
SPN version
Device type
ECU remote controlled

Speed deviation ECU
Setting range
Default value
0 to 255
0 to 255
Yes / No
Yes / No
Version 1 / Version 2 / Version 3
Off / Standard / S6 Scania /
EMR2 Deutz / EMS 2 Volvo /
ADEC MTU / EGS Woodward /
EDC7 MAN / EEM SISU /
Cummins
On / Off
0 to 1400 rpm
234
0
No
No
Version 1
Standard
On
120 rpm
DE
EN
Table 3-112: Application - standard values - configure CAN interface 2: J1939
CL2
15106
{0}
J1939 device addresses

J1939 Gerte-Adresse
{1o}
{1oc}
{2oc}
J1939 Interface: Own address
0 to 255
The easYgen sends J1939 request and control messages with this ID. It must be
changed for different ECU types according to the following table. The ECU
listens only to control messages, if they are sent to the correct address.
S6
Scania
39
EMR2
Deutz
3
EMS2
Volvo
17
ADEC
MTU
1
EGS
Woodward
234
EDC7
MAN
253
EEM
SISU
n/a
Cummins
220
DE
EN
Details may be found in the manual of the genset control and the interface
manual 37430.
Note: Changing this parameter becomes only effective after restarting the unit.
CL2
15107
{0}
Engine control address

Adresse Motorsteuerung
{1o}
{1oc}
{2oc}
J1939 Interface: Engine control address
Configures the address of the J1939 device, which is controlled.

S6
Scania
0
DE
EN
DE
EN
Reset previous act. DTCs - DM3

Quittieren passiver Fehler DM3
{1o}
{1oc}
{2oc}
CL2 {0}
15108
CL2
{0}
{1o}
DE
EN
15133
Reset act. DTCs - DM11

Quittieren activer Fehler DM11
CL2
15103
{0}
Woodward
{1o}
{1oc}
{2oc}
SPN version
SPN Version
{1oc}
{2oc}
0 to 255
EMR2
Deutz
0
EMS2
Volvo
0
ADEC
MTU
128
EGS
Woodward
0
J1939 Interface: Reset previously active DTCs - DM3
EDC7
MAN
39
EEM
SISU
0 / (1)
Cummins
0
Yes / No
If this parameter is set Yes, a DM3 message "Acknowledge passive faults" is

sent. After that this parameter is reset automatically to No.
As a result alarms (DM2) which no longer apply are cleared.
J1939 Interface: Reset active DTCs - DM11
Yes / No
If this parameter is set Yes, a DM11 message "Acknowledge active faults" is

sent. After that this parameter is reset automatically to No.
As a result alarms (DM1) which no longer apply are cleared.
J1939 Interface: SPN version
Version 1 / Version 2 / Version 3
The J1939 protocol provides 4 different versions for formatting Suspect

Parameter Number. This is important for a correct display of the alarm messages.
With this parameter it is defined if formatting occurs according to Version 1,
Version 2, or Version 3. Formatting according to Version 4 is identified
automatically.
Details may be found in the engine control J1939 manual.
Page 257/339
DE
EN
Manual 37427
CL2
15102
{0}
{1o}
Device type
Betriebsmodus
{1oc}
{2oc}
J1939 Interface: Device type
refer to selection below
The J1939 interface of this device may be operated with different engine control
units or analog input devices. This parameter determines the operating mode of
the used ECU.
Off................ The J1939 interface is disabled. No messages will be received.
Standard ..... Standard J1939 coupling is enabled: J1939 data is displayed
according to the SAE J1939 standard.
This setting must be configured for all J1939 ECUs, which cannot
be selected here (e.g. Deutz EMR3, John Deere, Perkins, Iveco,
Sisu, etc.).
S6 Scania ..... The Scania EMS/S6 ECU is enabled: J1939 data according to the
SAE J1939 standard and some S6-specific data are considered.
EMR2 Deutz The Deutz EMR2 ECU is enabled: J1939 data according to the
SAE J1939 standard and some EMR2-specific data are considered.
EMS2 Volvo The Volvo EMS2 ECU is enabled: J1939 data according to the
SAE J1939 standard and some EMS2-specific data are considered.
ADEC MTU The MTU ADEC ECU is enabled: J1939 data according to the
SAE J1939 standard and some ADEC-specific data are considered.
EGS Woodward ... The Woodward EGS ECU is enabled: J1939 data according
to the SAE J1939 standard and some EGS-specific data are
considered.
EDC7 MAN The MAN EDC7 ECU is enabled: J1939 data according to the
SAE J1939 standard and some EDC-specific data are considered.
EEM SISU The SISU EEM2/3 ECU is enabled: J1939 data according to the
SAE J1939 standard and some EEM2/3-specific data are
considered.
Cummins
The Cummins ECU is enabled: J1939 data according to the
SAE J1939 standard and some Cummins-specific data are
considered.
NOTE
Refer to the Appendix of the Interface Manual 37430 for a list of all ECUs, which are supported beyond
the J1939 standard.
This parameter must not be disabled if any J1939 device (like an analog input device) is connected to
the easYgen, even if no ECU is connected!
DE
EN
ECU remote controlled

Fernsteuern der ECU ber J1939
{1o}
{1oc}
{2oc}
CL2 {0}
15127
J1939 Interface: ECU remote control via J1939
On / Off
On ................ The unit sends J1939 control messages to the ECU. Depending on
the selected device type (Parameter 15102), contains a specific
selection of commands. Available messages are speed deviation
and droop for all ECUs as well as engine start/stop, enable idle
mode, rated speed switch and preglow for some ECUs. Refer to the
interface manual 37430 for more detailed information.
Off................ The ECU remote control via the J1939 protocol will be disabled.
NOTE
The unit sends J1939 control messages to the ECU. Depending on the selected device type (Parameter
15102), it contains a specific selection of commands. Available messages are speed deviation and
droop for ECUs as well as engine start/stop, enable idle mode, rated speed switch and preglow for
some ECUs. Refer to the interface manual 37430 for more detailed information.
Page 258/339
Woodward
DE
EN
Manual 37427
CL2
5537
{0}
Speed deviation ECU

Drehzahlhub
{1o}
{1oc}
{2oc}
J1939 Interface: Speed deviation
0 to 1400 rpm
This parameter is only visible if ECU remote controlled

(parameter 15127) is configured to "On".
This parameter adjusts the range of the speed deviation around the rated speed,
which is sent to the ECU.
It relates to the engine rated speed (parameter 1601). There are two methods of
sending the speed set point to the ECU: With a speed offset and a speed setpoint.
The frequency and power control must be configured to "PID".
Speed offset: S6 Scania, EMS2 Volvo, EGS Woodward, Cummins
The easYgen sends a speed offset with a range of 0 to 100% (every 20 ms). 50%
= rated speed. There is also an internal speed offset configured in the ECU, this
parameter determines what corresponds with 0% or 100%. If there is a positive
and a negative speed offset, they should be symmetrical in the ECU. We
recommend to have the same speed offset configured in the ECU and in this
parameter here. A different setting will result in an additional "controller gain".
How to test this parameter during commissioning:
Isolated operation: Disable the frequency controller and change parameter 5508
for the initial state between 0 and 100%, the engine should change the speed as
follows:
0 = rated speed negative speed offset from ECU
50 = rated speed
100 = rated speed + positive speed offset from ECU
Mains parallel operation: Check with the set point in the display if the engine is
able to deliver the full power.
Speed set point: EMR2 Deutz, ADEC MTU, EGS Woodward, EEM SISU,
Standard
The easYgen sends a speed set point in rpm (every 10 ms) that varies around the
rated speed in the range of +/- the speed deviation.
How to test this parameter during commissioning:
Isolated operation: Disable the frequency controller and change parameter 5508
for the initial state between 0 and 100%, the engine should change the speed as
follows:
0 = rated speed speed deviation ECU e.g. 1500 120 = 1380rpm
50 = rated speed
e.g.
= 1500rpm
100 = rated speed + speed deviation ECU e.g. 1500 + 120 = 1620rpm
Note: Keep this value as small as possible, i.e. do not enter a speed deviation of
500, if the engine varies only between 1400 and 1600rpm.
Mains parallel operation: Check with the set point in the display if the engine is
able to deliver the full power.
NOTE
The Wodward EGS ECU supports both types of speed deviation control and may be configured either
to "Speed offset" or "Speed set point".
In mains parallel operation, the EGS can be configured to receive a real power set point from the
easYgen to control the power. In this case, real power control must be disabled in the easYgen.
Woodward
Page 259/339
Manual 37427
Load Share Parameters

Parameter table
Level
Text
Configure CAN interface: load share
Load share Interface
Transfer rate LS fast message
Load Share CAN-ID
Setting range
Default value
CAN #1 / Off
0.10 to 0.30 s
2xx Hex / 3xx Hex
4xx Hex / 5xx Hex
CAN #1
0.10 s
5xx Hex
DE
EN
Table 3-113: Application - standard values - configure CAN interface: load share
CL2
DE
EN
9923
CL2
{0}
9920
{1oc}
{2oc}
Transfer rate LS fast message

Sendetakt der Lastverteilung
{0}
{1o}
DE
CL2
{1o}
EN
9921
Load share Interface

Schnittstelle Lastverteilung
{0}
{1oc}
{2oc}
Load Share CAN-ID

Lastverteilungs CAN-ID
Page 260/339
{1o}
{1oc}
{2oc}
CAN Interface: load share interface
CAN #1 / Off
The interface, which is used for transmitting the load share data is configured
here.
CAN Interface: transfer rate load share fast message
0.10 to 0.30 s
The transfer rate defines the time delay between two fast CAN messages.
In case of CAN systems with a high bus load (e.g. long distance between the
units with low baud rate), a shorter transfer rate (higher time setting) helps to
reduce the bus load.
CAN Interface: load share CAN ID
2xx Hex / 3xx Hex / 4xx Hex / 5xx Hex
The first digit of the CAN ID or the range (i.e. 2xx means 200 through 2FF) is
configured here. The last two digits will be assigned by the control with the
settings from the device number (parameter 1702 on page 32).
Woodward
Manual 37427
Configure Interfaces: Configure RS-232 Interfaces

Configure Serial Interface 1
Parameter table
Level
Text
Configure RS-232 interfaces: serial interface 1
Baudrate
Parity
Stop bits
ModBus Slave ID
Reply delay time
Setting range
Default value
2.4 / 4.8 / 9.6 / 14.4 / 19.2

38.4 / 56 / 115 kBd
No / Even / Odd
One / Two
0 to 255
0.00 to 1.00 s
19.2 kBd
No
One
1
0.00 s
DE
EN
Table 3-114: Application - standard values - configure RS-232 interface: serial interface 1
CL2
{0}
{1o}
{1oc}
DE
EN
3163
Baudrate
Baudrate
CL2
{0}
{1o}
DE
EN
3161
CL2
{0}
DE
EN
3162
CL2
DE
EN
3185
CL2
3186
{0}
{1o}
{1oc}
{2oc}
Parity
Parity
{2oc}
Stop bits
Stop Bits
{1oc}
{2oc}
ModBus Slave ID
ModBus Slave ID
{1o}
{1oc}
{2oc}
Reply delay time

Zeitverzger. der Antwort
{0}
Woodward
{1o}
{1oc}
{2oc}
Serial interface 1: Baud rate
2.4 / 4.8 / 9.6 / 14.4 / 19.2 / 38.4 / 56 / 115 kBaud
This parameter defines the baud rate for communications. Please note, that all
participants on the bus must use the same baud rate.
Serial interface 1: Parity
no / even / odd
The used parity of the interface is set here.

Serial interface 1: Stop bits
one / two
The number of stop bits is set here.

Serial interface 1: Modbus Slave ID
0 to 255
The Modbus device address, which is used to identify the device via Modbus, is
entered here. If "0" is configured here, the Modbus is disabled.
Serial interface 1: Reply delay time
0.00 to 1.00 s
This is the minimum delay time between a request from the Modbus master and the
sent response of the slave. This time is also required if an external interface
converter to RS-485 is used for example.
Page 261/339
Manual 37427
Configure Interfaces: Configure RS-485 Interfaces

Configure Serial Interface 2
Parameter table
Level
Text
Configure RS-232 interfaces: serial interface 1
Baudrate
Parity
Stop bits
ModBus Slave ID
Reply delay time
Setting range
Default value
2.4 / 4.8 / 9.6 / 14.4 / 19.2

38.4 / 56 / 115 kBd
No / Even / Odd
One / Two
0 to 255
0.00 to 2.55 s
19.2 kBd
No
One
1
0.00 s
DE
EN
Table 3-115: Application - standard values - configure RS-485 interface: serial interface 2
CL2
{0}
{1o}
{1oc}
DE
EN
3170
Baudrate
Baudrate
CL2
{0}
{1o}
DE
EN
3171
CL2
{0}
{1o}
DE
CL2
DE
EN
3188
CL2
3189
{0}
Parity
Parity
{2oc}
Stop bits
Stop Bits
{1oc}
{2oc}
ModBus Slave ID
ModBus Slave ID
EN
3172
{1oc}
{2oc}
{1o}
{1oc}
{2oc}
Reply delay time

Zeitverzger. der Antwort
{0}
{1o}
Page 262/339
{1oc}
{2oc}
Serial interface 2: Baud rate
2.4 / 4.8 / 9.6 / 14.4 / 19.2 / 38.4 / 56 / 115 kBaud
This parameter defines the baud rate for communications. Please note, that all
participants on the bus must use the same baud rate.
Serial interface 2: Parity
no / even / odd
The used parity of the interface is set here.

Serial interface 2: Stop bits
one / two
The number of stop bits is set here.

Serial interface 2: Modbus Slave ID
0 to 255
The Modbus device address, which is used to identify the device via Modbus, is
entered here. If "0" is configured here, the Modbus is disabled.
Serial interface 2: Reply delay time
0.00 to 2.55 s
This is the minimum delay time between a request from the Modbus master and the
sent response of the slave. This time is required in halfduplex mode.
Woodward
Manual 37427
Parameter table
Level
Text
Flag {x}
Timer 1: Hour
Timer 1: Minute
Timer 1: Second
Timer 2: Hour
Timer 2: Minute
Timer 2: Second
Active day
Active hour
Active minute
Active second
Monday active
Tuesday active
Wednesday active
Thursday active
Friday active
Saturday active
Sunday active
Use ASA symbols
Setting range
Default value
LogicsManager
0 to 23 h
0 to 59 min
0 to 59 s
0 to 23 h
0 to 59 min
0 to 59 s
1 to 31
0 to 23
0 to 59 min
0 to 59 s
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
(0 & 1) & 1
8h
0 min
0s
17 h
0 min
0s
1
12
0 min
0s
Yes
Yes
Yes
Yes
Yes
No
No
No
Table 3-116: Application - standard values - configure LogicsManager
DE
EN
The easYgen LogicsManager screens show logical symbols according to the IEC standard by default. However,
it is also possible to change the LogicsManager screens to ASA standard. Table 3-120 on page 272 shows the
symbols according to the different standards.
CL2
4117
Use ASA symbols

ASA Symbole verwenden
{0}
{1o}
{1oc}
{2oc}
Use ASA symbols
Yes / No
Yes ............... Symbols according to the ASA standard are used in LogicsManager
screens.
No ................. Symbols according to the IEC standard are used in LogicsManager
screens.
Configure LogicsManager: Configure Internal Flags
DE
EN
Internal flags within the LogicsManager logical outputs may be programmed and used for multiple functions. For
conditions and explanation of programming please refer to page 271 in chapter "LogicsManager").
CL2
yyyyy
{0}
{1o}
Flag {x}
Merker {x}
{1oc}
{2oc}
LogicsManager
Internal flags: Flag {x} [x = 1 to 16]
The flags may be used as auxiliary flags for complex combinations by using the
logical output of these flags as command variable for other logical outputs.
Flag {x}
Parameter ID yyyyy
Flag {x}
Parameter ID yyyyy
Flag 1
12230
Flag 9
12910
Flag 2
12240
Flag 10
12911
Flag 3
12250
Flag 11
12912
Flag 4
12260
Flag 12
12913
Flag 5
12270
Flag 13
12914
Flag 6
12280
Flag 14
12915
Flag 7
12290
Flag 15
12916
Flag 8
12300
Flag 16
12917
Table 3-117: Internal flags - parameter IDs
NOTE
Flag 1 is also used as placeholder in other logical combinations. Flag 8 is preset with a timer start and
shows different default values compared with Table 3-116.
Woodward
Page 263/339
Manual 37427
Configure LogicsManager: Set Timer
DE
EN
LogicsManager: Daily Time Set Point

Utilizing the LogicsManager it is possible to establish specific times of the day that functions (i.e. generator
exerciser) can be enabled. The two daily time set points are activated each day at the configured time. Using the
LogicsManager these set points may be configured individually or combined to create a time range.
CL2
{0}
DE
EN
1652
1657
CL2
DE
EN
1651
1656
CL2
1650
1655
{0}
Timer {x}: Hour

Zeitpunkt {x}: Stunde
{1o}
{1oc}
{2oc}
Timer {x}: Minute

Zeitpunkt {x}: Minute
{1o}
{1oc}
{2oc}
Timer {x}: Second

Zeitpunkt {x}: Sekunde
{0}
{1o}
{1oc}
{2oc}
Timer: Daily time set point {x} [x = 1/2]: hour
0 to 23 h
Enter the hour of the daily time set point here. Example:
23 ..................23rd hour of the day (11pm).
Timer: Daily time set point {x} [x = 1/2]: minute
0 to 59 min
Enter the minute of the daily time set point here. Example:
Timer: Daily time set point {x} [x = 1/2]: second
0 to 59 s
Enter the second of the daily time set point here. Example
0 ....................0th second of the minute.
59 ..................59th second of the minute.
DE
EN
LogicsManager: Active Time Set Point

Utilizing the LogicsManager it is possible to establish specific days (or hours, minutes, seconds) that functions
(i.e. generator exerciser) can be enabled. The active switching point is activated only on a specified day (or hour,
minute, second). The set points may be configured individually or combined via the LogicsManager. You may
configure monthly, daily, hourly, minutely, or even secondly time set points depending on how you combine the
set points in the LogicsManager.
CL2
{0}
{1o}
DE
EN
1663
CL2
{0}
{1o}
DE
EN
1662
CL2
1661
{0}
{1o}
Page 264/339
Active day
Aktiver Tag
{1oc}
{2oc}
Active hour
Aktive Stunde
{1oc}
{2oc}
Active minute
Aktive Minute
{1oc}
{2oc}
Timer: Active time set point: day
1 to 31
Enter the day of the active switch point here. Example:

01 ..................1st day of the month.
31 ..................31st day of the month.
The active time set point is enabled during the indicated day from 0:00:00 hours to
23:59:59 hours.
Timer: Active time set point: hour
0 to 23 h
Enter the hour of the active switch point here. Example:

0 ....................0th hour of the day.
23 ..................23rd hour of the day.
The active time set point is enabled every day during the indicated hour from
minute 0 to minute 59.
Timer: Active time set point: minute
0 to 59 min
Enter the minute of the active switch point here. Example:

The active time set point is enabled every hour during the indicated minute from
second 0 to second 59.
Woodward
DE
EN
Manual 37427
CL2
1660
{0}

Active second
Aktive Sekunde
{1o}
{1oc}
{2oc}
Timer: Active time set point: second
0 to 59 s
Enter the second of the active switch point here. Example:

0.................... 0th second of the minute.
59.................. 59th second the minute.
The active time set point is enabled every minute during the indicated second.
LogicsManager: Weekly Time Set Point

Utilizing the LogicsManager it is possible to establish specific days of the week that functions (i.e. generator
exerciser) can be enabled. The weekly time set point is enabled during the indicated day from 0:00:00 hours to
23:59:59 hours.
DE
EN
Monday active
Montag aktiv
CL2
{0}
{1o}
DE
CL2
{0}
DE
EN
1671
CL2
{0}
DE
EN
1672
CL2
{0}
{1o}
{1o}
{1o}
{0}
{1o}
DE
CL2
{0}
{1o}
DE
EN
1675
CL2
1676
{0}
Woodward
{1oc}
{2oc}
{1oc}
{2oc}
{1oc}
{2oc}
Friday active
Freitag aktiv
{1oc}
{2oc}
Saturday active
Samstag aktiv
EN
1674
{2oc}
Thursday active
Donnerstag aktiv
DE
CL2
Wednesday active
Mittwoch aktiv
EN
1673
{1oc}
Tuesday active
Dienstag aktiv
EN
1670
{1o}
{1oc}
{2oc}
Sunday active
Sonntag aktiv
{1oc}
{2oc}
Timer: Weekly time set points Monday: days
Yes / No
Please enter the days of the weekly workdays.

Monday ........... Yes The switch point is enabled every Monday
No The switch point is disabled every Monday
Timer: Weekly time set points Tuesday: days
Yes / No

Tuesday ........... Yes The switch point is enabled every Tuesday
No The switch point is disabled every Tuesday
Timer: Weekly time set points Wednesday: days
Yes / No

Wednesday ...... Yes The switch point is enabled every Wednesday
No The switch point is disabled every Wednesday
Timer: Weekly time set points Thursday: days
Yes / No

Thursday ......... Yes The switch point is enabled every Thursday
No The switch point is disabled every Thursday
Timer: Weekly time set points Friday: days
Yes / No

Friday .............. Yes The switch point is enabled every Friday
No The switch point is disabled every Friday
Timer: Weekly time set points Saturday: days
Yes / No

Saturday .......... Yes The switch point is enabled every Saturday
No The switch point is disabled every Saturday
Timer: Weekly time set points Sunday: days
Yes / No

Sunday ............. Yes The switch point is enabled every Sunday
No The switch point is disabled every Sunday
Page 265/339
Manual 37427
Configure Counters
Parameter table
Level
Text
Configure counters
Maintenance hours
Reset maintenance period hrs
Maintenance days
Reset maintenance period days
Code level for reset maint.
Counter value preset
Set operation hours in 0.00h
Gen. active power [0.00MWh]
Set number of starts
Setting range
Default value
0 to 9999 h
Yes / No
0 to 999 d
Yes / No
0 to 3
0 to 99999999
Yes / No
0 to 99999999
Yes / No
0 to 65535
Yes / No
300 h
No
365 d
No
3
0
No
0
No
0
No
Table 3-118: Application - standard values - configure counters
Configure Counters: Maintenance Call
DE
EN
A maintenance call will be issued if the configured number of maintenance hours has expired or the configured
number of days has expired since the last maintenance.
In case of a maintenance call, the display indicates "Mainten. days exceeded" or "Mainten. hours
exceeded".
CL2
2550
Maintenance hours
Wartungsintervall Stunden
{0}
{1o}
{1oc}
{2oc}
Counter: Maintenance interval 'Hours'
0 to 9,999 h
To disable the maintenance "hours" counter configure "0" for this entry.
This parameter defines the remaining hours until the next maintenance call
occurs. Once the generator has been operated for the number of hours configured
here, a maintenance message is displayed.
DE
EN
If the maintenance counter is reset either by the push-buttons at the front panel
(refer to manual 37428), or by configuring the parameter "Reset maintenance
call" to "Yes" (parameter 2562 on page 266), the maintenance counter is reset to
the configured value.
CL2
2562
Reset maintenance period hrs

Wartungsstunden rcksetzen
{0}
{1o}
{1oc}
{2oc}
Counter: Reset maintenance call counter 'Hours'
Yes / No
If this parameter is configured to "Yes" the maintenance "hours" counter is reset

to the configured value. Once the counter has been reset, the control unit changes
this parameter to "No".
Note: When using a specific code level in parameter 2567 for reset of maint.
hours this parameter can be blocked.
Page 266/339
Woodward
DE
EN
Manual 37427
CL2
2551
{0}
Counter: Maintenance interval 'Days'
Maintenance days
Wartungsintervall Tage
{1o}
{1oc}
0 to 999 days
To disable the maintenance "days" counter configure "0" for this entry.
{2oc}
DE
EN
This parameter defines the remaining days until the next maintenance call occurs.
Once the configured number of days has expired since the last maintenance, a
maintenance message is displayed.
If the maintenance counter is reset either by the push-buttons at the front panel
(refer to manual 37428), or by configuring the parameter "Reset maintenance
call" to "Yes" (parameter 2563 on page 267), the maintenance counter is reset to
the configured value.
CL2
2563
Counter: Reset maintenance call counter 'Days'
Reset maintenance period days

Wartungstage rcksetzen
{0}
{1o}
{1oc}
Yes / No
If this parameter is configured to "Yes" the maintenance "days" counter is reset to

the configured value. Once the counter has been reset, the control unit changes
this parameter to "No".
{2oc}
Note: When using a specific code level in parameter 2567 for reset of maint. days
this parameter can be blocked.
Counter: Code level for resetting the maintenance call
DE
EN
Code level for reset maint.

Codeebene fr Wartung rckset.
{1o}
{1oc} {2oc}
CL2 {0}
2567
0 to 3
This parameter determines the required code level for resetting the counter
"Maintenance call in...". User with a lower code level may not access this function.
The following code levels exist:
3 = Commissioner
2 = Temporary commissioner
1 = Service level
0 = Operator
DE
EN
Configure Counters: Operation Hours, kWh, and kvarh
CL2
2515
{0}

Zhler-Setzwert
{1o}
{1oc}
{2oc}
Counter: Set point value for counters
0 to 99,999,999
This value is utilized to set the following counters:

operation hours counter
kWh counter
kvarh counter
DE
EN
The number entered into this parameter is the number that will be set to the
parameters listed above when they are enabled.
CL2
DE
EN
2574
CL2
2510
Set operation hours in 0.00h

Betriebsstd. setzen in 0.00h
{0}
{1o}
{1oc}
{2oc}
Gen. active power [0.00MWh]

Gen. Wirkarbeit [0,00MWh]
{0}
Woodward
{1o}
{1oc}
{2oc}
Counter: Set operation hours counter
Yes / No
Yes ................ The current value of this counter is overwritten with the value
configured in "set point value for counters". After the counter has
been (re)set, this parameter changes back to "No" automatically.
No ................. The value of this counter is not changed.
Counter: Set kWh counter
Yes / No
Yes ................ The current value of this counter is overwritten with the value
configured in "set point value for counters". After the counter has
been (re)set, this parameter changes back to "No" automatically.
No ................. The value of this counter is not changed.
Page 267/339
Manual 37427
NOTE
Example: The counter value preset (parameter 2515 on page 267) is configured to "3456".
If parameter 2574 will be configured to Yes, the operation hour counter will be set to 3456h.
If parameter 2510 will be configured to Yes, the active energy counter will be set to 34.56MWh.
DE
EN
Configure Counters: Start Counter
CL2
{0}
DE
EN
2541
CL2
2542
{0}
Page 268/339

Zhler-Setzwert
{1o}
{1oc}
{2oc}
Set number of starts

Anzahl Starts setzen
{1o}
{1oc}
{2oc}
Counter: Set point value for start counter
0 to 65535
This parameter defines the number of times the control unit registers a start of
the generator set. The number entered here will overwrite the current displayed
value after confirming with parameter 2542 on page 268.
Counter: Set start counter
Yes / No
Yes ................ The current value of the start counter is overwritten with the value
configured in "Set point value for start counter". After the counter
has been (re)set, this parameter changes back to "No"
automatically.
No ................. The value of this counter is not changed..
Woodward
Manual 37427
Appendix A.
Miscellaneous
Alarm Classes
The control functions are structured in the following alarm classes:

Alarm class
Control
Visible in the display
LED "Alarm"
& horn
Relay "Command:
open GCB"
Shut-down engine
Engine blocked until

ack. sequence has
been performed
yes
no
no
no
no
yes
yes
no
no
no
yes
yes
soft unloading
cool down time
yes
yes
yes
immediately
cool down time
yes
yes
yes
soft unloading
immediately
yes
yes
yes
immediately
immediately
yes
no
no
no
no
no
Warning Alarm
This alarm does not interrupt the unit operation. A message output without a centralized alarm occurs:
Alarm text.
Warning Alarm
This alarm does not interrupt the unit operation. An output of the centralized alarm occurs and the command variable 3.05
(horn) is issued.
Alarm text + flashing LED "Alarm" + Relay centralized alarm (horn).
Shutdown Alarm
With this alarm the GCB is opened and the engine is stopped. Coasting occurs.
Alarm text + flashing LED "Alarm" + Relay centralized alarm (horn) + GCB open + Coasting + Engine stop.
Shutdown Alarm
With this alarm the GCB is opened and the engine is stopped. Coasting occurs.
Alarm text + flashing LED "Alarm" + Relay centralized alarm (horn) + GCB open + Coasting + Engine stop.
Shutdown Alarm
With this alarm the GCB is opened immediately and the engine is stopped.
Alarm text + flashing LED "Alarm" + Relay centralized alarm (horn)+ GCB open + Engine stop.
Shutdown Alarm
With this alarm the GCB is opened immediately and the engine is stopped.
Alarm text + flashing LED "Alarm" + Relay centralized alarm (horn)+ GCB open + Engine stop.
Control Signal
This signal issues a control command only. It may be assigned to a discrete input for example to get a control signal, which
may be used in the LogicsManager. No alarm message and no entry in the alarm list or the event history will be issued.
This signal is always self-acknowledging, but considers a delay time and may also be configured with an engine delay.
CAUTION
If an alarm of class C, D, or E is present and the GCB cannot be opened, the engine will not be stopped.
This can only be achieved by enabling GCB monitoring (parameter 2600 on page 114) with the alarm
class configured to "F" (parameter 2601 on page 114).
NOTE
If an alarm has been configured with a shutdown alarm that has been enabled to self-acknowledge, and
has been configured as engine delayed the following scenario may happen:
The alarm shuts down the engine because of its alarm class.
Due to the engine stopping, all engine delayed alarms are ignored.
The alarm class is acknowledged automatically.
The alarm will self-acknowledge and clear the fault message that shut the engine down. This
prevents the fault from being analyzed. After a short delay, the engine will restart.
After the engine monitoring delay expires, the fault that originally shut down the engine will do so
again. This cycle will continue to repeat until corrected.
Woodward
Page 269/339
Manual 37427
Conversion Factors
Temperature
C F
F C
T [F] = (T [C] x 1.8) + 32
T [C] = (T [F] 32) / 1.8
bar psi
psi bar
P [psi] = P [bar] x 14.503
P [bar] = P [psi] / 14.503
Pressure
Page 270/339
Woodward
Manual 37427
Appendix B.
LogicsManager
The LogicsManager is used to customize the sequence of events in the control unit such as the start command of
the engine or the operation of control unit relay outputs. For example, the start routine may be programmed so
that it requires the closing of a discrete input or a preset time of day. Depending on the application mode of the
unit, the number of available relays that may be programmed with the LogicsManager will vary. Two
independent time delays are provided for the configured action to take place and be reset.
Structure and Description of the LogicsManager
Command [C1]
Sign [S1]
Command [C2]
Sign [S2]
Command [C3]
Sign [S3]
Figure 3-32: LogicsManager - function overview
Command (variable) - A list of over 400 parameters and functions is provided for the command inputs.
Examples of the parameters that may be configured into these commands are generator undervoltage
thresholds 1 and 2, start fail, and cool down. These command variables are used to control the output function
or relay. Refer to Logical Command Variables starting on page 277 for a complete list of all command
variables.
Sign - The sign field can be used to invert the state of the command or to fix its output to a logical true or
false if the command is not needed. Setting the sign to the NOT state changes the output of the command
variable from true to false or vice versa.
Operator - A logical device such as AND or OR.
(Logical) output - The action or control sequence that occurs when all parameters set into the
LogicsManager are met.
[Cx] - Command {x}
The description and the tables of

all values, flags, and internal
functions that are able to
combine via the LogicsManager
can be found in the Logical
Command Variables section
starting on page 277.
[Sx] - Sign {x}

Value {[Cx]}
The value [Cx] is
passed 1:1.
[Ox] - Operator {x}
NOT Value {[Cx]}

The opposite of the
value [Cx] is passed.
NAND
Logical negated AND
0 [False; always "0"]

The value [Cx] is ignored and
this logic path
will always be FALSE.
1 [True; always "1"]
The value [Cx] is ignored and
this logic path
will always be TRUE.
[Ax] - Output {x}
AND
Logical AND
OR
Logical OR
NOR
Logical negated OR
XOR
Exclusive OR
The description and the tables of

all logical outputs, flags, and
functions that are able to
combine via the LogicsManager
can be found in the Logical
Outputs section starting on
page 273.
NXOR
Exclusive negated OR
(See Table 3-120 for symbols)
Table 3-119: LogicsManager - command overview
Woodward
Page 271/339
Manual 37427
Configuration of the Command Chain

Using the values specified in the above table, the chain of commands of the LogicsManager (for example:
operating the relays, setting the flags, specification of the automatic functions) is configured as follows:
[Ax] = ( ( [C1] & [S1] ) & [O1] & ( [C2] & [S2] ) ) & [O2] & ( [C3] & [S3] )
Programming example for the LogicsManager:
Relay [R2] shall energize, whenever "Discrete input [D2]" is energized "AND" the control does "NOT" have a
fault that is "Alarm class C" "AND" does "NOT" have a fault that is "Alarm class D"
Figure 3-33: LogicsManager - display in ToolKit
Figure 3-34: LogicsManager - display on LCD screen
Logical Symbols
The following symbols are used for the graphical programming of the LogicsManager. The easYgen displays
symbols according to the IEC standard by default. It is possible to change to ASA standard display using
parameter 4117 on page 263.
ToolKit
easYgen
(default)
AND
OR
NAND
NOR
NXOR
XOR
&
>=1
&
>=1
=1
DIN 40 700
ASA
US MIL
(configurable)
IEC617-12
Truth
table
x1
0
0
1
1
x2
0
1
0
1
y
0
0
0
1
x1
0
0
1
1
x2
0
1
0
1
y
0
1
1
1
x1
0
0
1
1
x2
0
1
0
1
y
1
1
1
0
x1
0
0
1
1
x2
0
1
0
1
y
1
0
0
0
x1
0
0
1
1
x2
0
1
0
1
y
1
0
0
1
x1
0
0
1
1
x2
0
1
0
1
y
0
1
1
0
Table 3-120: LogicsManager - logical symbols
Page 272/339
Woodward
Manual 37427
Logical Outputs
The logical outputs or combinations may be grouped into three categories:

Internal logical flags
Internal functions
Relay outputs
NOTE
The numbers of the logical outputs in the third column may again be used as input variable for other
outputs in the LogicsManager.
Logical Outputs: Internal Flags

16 internal logical flags may be programmed to activate/deactivate functions. This permits more than
3 commands to be included in a logical function. They may be used like "auxiliary flags".
Name
Flag 1
Flag 2
Flag 3
Flag 4
Flag 5
Flag 6
Flag 7
Flag 8
Flag 9
Flag 10
Flag 11
Flag 12
Flag 13
Flag 14
Flag 15
Flag 16
Woodward
Function
Internal flag 1
Internal flag 2
Internal flag 3
Internal flag 4
Internal flag 5
Internal flag 6
Internal flag 7
Internal flag 8
Internal flag 9
Internal flag 10
Internal flag 11
Internal flag 12
Internal flag 13
Internal flag 14
Internal flag 15
Internal flag 16
Number
00.01
00.02
00.03
00.04
00.05
00.06
00.07
00.08
00.30
00.31
00.32
00.33
00.34
00.35
00.36
00.37
Page 273/339
Manual 37427
Logical Outputs: Internal Functions

The following logical functions may be used to activate/deactivate functions.
Name
Start request in AUTO
Stop request in AUTO
Inhibit emergency run
Undelay close GCB
Constant idle run
External acknowledge
Operation mode AUTO
Operation mode MAN
Operation mode STOP
Start without load
Automatic idle mode
Discrete f/P +
Discrete f/P Discrete V/PF +
Discrete V/PF Freq. Droop active
Volt. Droop active
Critical mode
Firing speed
Frequency setpoint 2
Load setpoint 2
Voltage setpoint 2
Power factor setpoint 2
Enable MCB
Load-dependent start/stop
Segment no.2 act
LDSS Priority 2
LDSS Priority 3
LDSS Priority 4
Transition mode 1
Page 274/339
Function
Start in AUTOMATIC operating mode (parameter 12120 on page 191)
Stop in AUTOMATIC operating mode (parameter 12190 on page 192)
Blocking or interruption of an emergency power operating in
AUTOMATIC operating mode (parameter 12200 on page 190)
Immediately closing of the GCB after engine start without waiting for the
engine delayed monitoring and generator stable timer to expire
(parameter 12210 on page 151)
Enables idle/rated speed modes (parameter 12550 on page 188).
The alarm acknowledgement is performed from an external source
(parameter 12490 on page 124)
Activation of the AUTOMATIC operating mode (parameter 12510 on
page 209)
Activation of the MANUAL operating mode (parameter 12520 on
page 209)
Activation of the STOP operating mode (parameter 12530 on page 209)
Starting the engine without closing the GCB (parameter 12540 on
page 209)
Automatic idle mode (blocks the undervoltage, underfrequency, and
underspeed monitoring for a configured time automatically,
parameter 12570 on page 188)
Raise frequency / real power set point (parameter 12900 on page 245)
Lower frequency / real power set point (parameter 12901 on page 245)
Raise voltage / power factor set point (parameter 12902 on page 245)
Lower voltage / power factor set point (parameter 12903 on page 245)
Activation of the frequency droop (parameter 12904 on page 221)
Activation of the voltage droop (parameter 12905 on page 233)
Activation of critical mode operation (parameter 12220 on page 214)
Firing (ignition) speed is reached (parameter 12500 on page 184)
Activates the frequency set point 2 (parameter 12918 on page 220)
Activates the load set point 2 (parameter 12919 on page 226)
Activates the voltage set point 2 (parameter 12920 on page 232)
Activates the power factor set point 2 (parameter 12921 on page 237)
Enables the MCB (parameter 12923 on page 155)
Activation of load-dependent start/stop (parameter 12930 on page 196)
Assigns the genset to load share segm. #2 (parameter 12929 on page 244)
Sets the LDSS priority to 2 (parameter 12926 on page 197)
Activates breaker transition mode 1 (parameter 12931 on page 143)
Number
00.09
00.10
00.11
00.12
00.14
00.15
00.16
00.17
00.18
00.19
00.20
00.21
00.22
00.23
00.24
00.25
00.26
00.28
00.29
00.81
00.82
00.83
00.84
00.85
00.86
00.87
00.90
00.91
00.92
00.93
Woodward
Manual 37427
Priority Hierarchy of the Logical Outputs

The following table contains the priority relationships between the start conditions of the logical outputs in the
LogicsManager:
Prioritized function
Critical mode
overrides
Stop req. in Auto
Start req. in Auto
Stop req. in Auto
Start req. in Auto

Emergency power
Idle mode
Start req. in Auto
Start w/o load
Critical mode
Start w/o load

Emergency power
Inhibit emergency run
Woodward
Emergency power
Emergency power
during Start w/o load
Reaction
A start will still be performed.
The behavior of the system depends on the configuration of the related
parameters.
No start will be performed.
The GCB remains open / will be opened.
The GCB will be closed nevertheless.
The GCB will be closed nevertheless. The alarm class management is still
performed like for the critical mode.
If emergency power is already enabled and the critical mode will be enabled
then, a pause time may be configured for the emergency power operation.
The generator keeps on running without taking over load.
Page 275/339
Manual 37427
Logical Outputs: Relay Outputs

All relays may be controlled directly by the LogicsManager depending on the respective application mode.
Name
Relay 1
(Ready for operation OFF)
Relay 2
Relay 3
Relay 4
Relay 5
Relay 6
Relay 7
Relay 8
Relay 9
Relay 10
Relay 11
External DO 1
External DO 2
External DO 3
External DO 4
External DO 5
External DO 6
External DO 7
External DO 8
External DO 9
External DO 10
External DO 11
External DO 12
External DO 13
External DO 14
External DO 15
External DO 16
Function
If this logical output becomes true, the relay output 1 will be activated
Number
00.41
If this logical output becomes true, the external relay output 1 will be activated
00.42
00.43
00.44
00.45
00.46
00.47
00.48
00.49
00.50
00.51
00.63
00.64
00.65
00.66
00.67
00.68
00.69
00.70
00.71
00.72
00.73
00.74
00.75
00.76
00.77
00.78
Table 3-119 shows the function of each relay in each of the application modes.
Relay
Number
Term.
Internal relay outputs

[R1]
30/31
[R2]
32/33
[R3]
34/35
[R4]
36/37
[R5]
38/39/40
[R6]
41/42
[R7]
80/81
[R8]
82/83
[R9]
84/85
[R10]
86/87
[R11]
88/89
None
{0}
Application mode (parameter 3401 on page 139)

GCB open
GCB open/close
{1o}
{1oc}
GCB/MCB open/close
{2oc}
LogicsManager; pre-assigned with 'Ready for operation OFF'

LogicsManager; pre-assigned with 'Centralized alarm (horn)'
LogicsManager; pre-assigned with 'Starter'
LogicsManager; pre-assigned with 'Diesel: Fuel solenoid, Gas: Gas valve'
LogicsManager; pre-assigned with 'Warning alarm'
Command: open MCB
LogicsManager
Command: close GCB
LogicsManager
Command: open GCB
LogicsManager; pre-assigned with 'Mains decoupling'
Command: close MCB
LogicsManager; pre-assigned with 'Stop solenoid'
LogicsManager; pre-assigned with 'Auxiliary services'
LogicsManager; pre-assigned with 'Shut down alarm'
Table 3-121: Relay outputs - terminal assignment
Page 276/339
Woodward
Manual 37427
Logical Command Variables
The logical command variables are grouped into different categories:
Group 00:
Group 01:
Group 02:
Group 03:
Group 04:
Group 05:
Group 06:
Group 07:
Group 08:
Group 09:
Group 10:
Group 11:
Group 12:
Group 13:
Group 14:
Group 15:
Group 18:
Woodward
Flags condition 1
Alarm system
Systems condition
Engine control
Applications condition
Engine related alarms
Generator related alarms
Mains related alarms
System related alarms
Discrete inputs
Analog inputs
Clock and timer
External DIs 1
Discrete outputs
External DOs 1
Flexible limits
Transistor outputs
Page 277/339
Manual 37427
Logical Command Variables: Group 00: Flags Condition 1

Flags condition 1, Logic command variables 00.01-00.94
Internal Flags are the result of the output of the logic ladders from Flag 1 to 16. Flags are internal logic that can
be sent to other flags or Command variables.
No.
00.01
00.02
00.03
00.04
00.05
00.06
00.07
00.08
00.09
00.10
00.11
ID
0
1
2
3
4
5
6
7
8
9
10
Name
LM: Flag 1
LM: Flag 2
LM: Flag 3
LM: Flag 4
LM: Flag 5
LM: Flag 6
LM: Flag 7
LM: Flag 8
LM: Start request in AUTO
LM: Stop request in AUTO
LM: Inhibit emergency run
00.12 11
LM: Undelay close GCB
00.14 13
LM: Constant idle run
00.15 14
LM: External acknowledge
00.16 15
LM: Operation mode AUTO
00.17 16
00.18 17
00.19 18
LM: Operation mode MAN

LM: Operation mode STOP
LM: Start w/o load
00.20 19
LM: Automatic idle mode
00.21
00.22
00.23
00.24
00.25
00.26
00.28
00.29
00.30
00.31
00.32
00.33
00.34
00.35
00.36
00.37
LM: Discrete f/P +

LM: Discrete f/P LM: Discrete V/PF +
LM: Discrete V/PF LM: Freq. Droop active
LM: Volt. Droop active
LM: Critical mode
LM: Firing speed
LM: Flag 9
LM: Flag 10
LM: Flag 11
LM: Flag 12
LM: Flag 13
LM: Flag 14
LM: Flag 15
LM: Flag 16
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
36
Page 278/339
Function
Internal flag 1
Internal flag 2
Internal flag 3
Internal flag 4
Internal flag 5
Internal flag 6
Internal flag 7
Internal flag 8
Start in AUTOMATIC operating mode
Stop in AUTOMATIC operating mode
Blocking or interruption of an emergency
power operation in AUTOMATIC
operating mode
Immediately closing of the GCB without
waiting for the engine delayed
monitoring timer to expire
Constant idle speed mode enabled
(blocks alarm for undervoltage,
underfrequency, and underspeed
constantly)
The alarm acknowledgement is
performed from an external source
Activation of the AUTOMATIC
operating mode
Activation of the MANUAL op. mode
Activation of the STOP operating mode
Starting the engine without closing the
GCB
Automatic idle speed mode (blocks
alarm for undervoltage, underfrequency,
and underspeed automatically for a set
time)
Raise frequency / real power set point
Lower frequency / real power set point
Raise voltage / power factor set point
Lower voltage / power factor set point
Frequency droop active
Voltage droop active
Activation of critical mode operation
Firing (ignition) speed is reached.
Internal flag 9
Internal flag 10
Internal flag 11
Internal flag 12
Internal flag 13
Internal flag 14
Internal flag 15
Internal flag 16
Note
Internal calculation; descr. page 273


Woodward
Manual 37427
No.
00.41
00.42
00.43
00.44
00.45
00.46
00.47
00.48
00.49
00.50
00.51
00.63
00.64
00.65
00.66
00.67
00.68
00.69
00.70
00.71
00.72
00.73
00.74
00.75
00.76
00.77
00.78
00.81
00.82
00.83
00.84
00.85
00.86
00.87
00.90
00.91
00.92
00.93
ID
40
41
42
43
44
45
46
47
48
49
50
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
80
81
82
83
84
85
86
89
90
91
92
Woodward
Name
LM: Relay 1
LM: Relay 2
LM: Relay 3
LM: Relay 4
LM: Relay 5
LM: Relay 6
LM: Relay 7
LM: Relay 8
LM: Relay 9
LM: Relay 10
LM: Relay 11
LM: External relay DO 1
LM: Setpoint 2 frequency
LM: Setpoint 2 load
LM: Setpoint 2 voltage
LM: Setpoint 2 power factor
LM: Enable MCB
LM: LD start/stop
LM: Segment no.2 act
LM: LDSS Priority 2
LM: LDSS Priority 3
LM: LDSS Priority 4
LM: Transition mode 1
Function
Note
TRUE, if the LogicsManager

condition driving this relay is
fulfilled; refer to page 170 for more
information
TRUE, if the LogicsManager

condition driving this relay is
fulfilled; refer to page 171 for more
information
Activation of frequency set point 2

Activation of load set point 2
Activation of voltage set point 2
Activation of power factor set point 2
MCB is enabled
Activation of load-dependent start/stop
Assigns the genset to load share segm. 2
Sets the LDSS priority to 2
Activates breaker transition mode 1

Page 279/339
Manual 37427
Logical Command Variables: Group 01: Alarm System

Alarm system, Logic command variables 01.01-01.11
Alarm classes may be configured as command variables for all logical outputs in the LogicsManager. Refer to
page 269 for a description of the alarm classes.
No.
01.01
01.02
01.03
01.04
01.05
01.06
01.07
ID
99
100
101
102
103
104
105
Name / Function
Alarm class A
Alarm class B
Alarm class C
Alarm class D
Alarm class E
Alarm class F
All alarm classes
01.08 106
Warning alarm
01.09 107
Shutdown alarm
01.10 108
Centralized alarm
01.11 109
New alarm triggered
Page 280/339
Note
TRUE as long as an alarm of this alarm class is active or latched (triggered)
TRUE as long as at least one alarm of the alarm classes A/B/C/D/E/F is active or
latched (triggered)
TRUE as long as at least one alarm of the alarm classes A/B is active or latched
(triggered)
TRUE as long as at least one alarm of the alarm classes C/D/E/F is active or latched
(triggered)
TRUE as long as at least one alarm of the alarm classes B/C/D/E/F is active or latched
(triggered)
TRUE if any alarm has been triggered until it is acknowledged
Woodward
Manual 37427
Logical Command Variables: Group 02: Systems Condition

Systems condition, Logic command variables 02.01-02.22
The status of the system may be used as command variable in a logical output to set parameters for customized
operations.
No.
ID Name
02.01 119 Firing speed detected
02.02 120 Speed detected
02.03 121 Generator voltage ok

02.04 122 Generator frequency ok
02.05 123 Generator ok
02.09 127 Mains voltage ok
02.10 128 Mains frequency ok
02.11 129 Mains ok
02.12
02.13
02.14
02.15
02.21
130
131
132
133
139
Woodward
Generator rotation CCW

Generator rotation CW
Mains rotation CCW
Mains rotation CW
Busbar 1 is dead
Function
Firing speed recognized (via MPU/gen.
frequency / LogicsManager)
Note
TRUE as long as at least firing speed
is measured (defined by parameter
3313 on page 184) either via the MPU
or the generator frequency; or is
detected via the LogicsManager
output "ignition speed reached"
(defined by parameters 3324 and
12500 on page 184)
Speed recognized (via MPU/gen.
TRUE as long as a speed is measured
frequency / LogicsManager)
(this can be lower that the ignition
speed; either via the MPU, the
generator frequency, or the
LogicsManager output "ignition speed
reached")
Generator voltage within operating
TRUE as long as the generator voltage
window
is within the operating window
Generator frequency within operating
TRUE as long as the generator
window
frequency is within the operating
window
Generator voltage and frequency within
TRUE as long as the generator voltage
operating windows
and frequency are within the operating
windows (02.03. and 02.04 are TRUE)
Mains voltage within operating window
TRUE as long as the mains voltage is
within the operating window
Mains frequency within operating window TRUE as long as the mains frequency
is within the operating window
Mains voltage and frequency within
TRUE as long as the mains voltage
operating windows
and frequency are within the operating
windows (02.09. and 02.10 are TRUE)
Generator voltage: rotating direction CCW TRUE as long as the respective
Generator voltage: rotating direction CW rotation field is detected in case of a
three-phase voltage measurement at
Mains voltage: rotating direction CCW
the respective measuring location
Mains voltage: rotating direction CW
Busbar 1 is dead
TRUE as long as the busbar voltage is
below the value configured in
parameter 5820 (Dead bus detection
max. volt.)
Page 281/339
Manual 37427
Logical Command Variables: Group 03: Engine Control

Engine control, Logic command variables 03.01-03.37
These variables may be used as command variable in a logical output to set parameters for customized
operations.
No.
ID Name / Function
03.01 179 Auxiliary services
03.02 180 Starter
03.04 182 Preglow (Diesel)
Ignition (Gas)
03.05 183 Horn (active)
03.06 184 Engine released
03.07 185 Engine delay over (engine delayed monitoring
expired)
03.08 186 Breaker delay over (engine delayed monitoring
expired)
03.13 191 Blinking lamp ECU
03.14 192 ECU special ignition
Note
TRUE if an auxiliary services prerun or postrun is
enabled
TRUE if the starter relay is energized
TRUE if the preglow (Diesel) or ignition (gas) relay is
energized
TRUE if alarm class B to F is activated until the time until
horn reset is expired or it is acknowledged for the first
time.
TRUE if the engine is requested and the start is released
TRUE after expiration of the "delayed engine monitoring"
timer until the fuel relay is de-energized
TRUE after expiration of the "breaker delay" timer until
the fuel relay is de-energized (= CB may be closed)
TRUE as soon as the ECU activates the diagnosis light
(only for Scania S6 ECU). This command variable is only
active if remote control of the ECU via easYgen is
activated.
TRUE as long as a reset or read-out of the Scania S6 ECU
blink code is requested (only for S6 Scania ECU). This
command variable is only active if remote control of the
ECU via easYgen is activated.
03.20 198 Three-position controller output: frequency / active

power (governor) raise
03.21 199 Three-position controller output: frequency / active
power (governor) lower
TRUE if the respective three-position controller issues the
03.22 200 Three-position controller output: voltage / reactive respective control pulse
power (AVR) raise
03.23 201 Three-position controller output: voltage / reactive
power (AVR) lower
03.27 205 Stopping solenoid (Diesel)
TRUE if a stop signal is issued until the stop time of
engine expires
03.28 206 Operating solenoid (Diesel)
TRUE if the fuel solenoid (Diesel) or gas valve (gas)
Gas valve (Gas)
relay is energized
03.30 208 Auxiliary services prerun
TRUE, if "Auxiliary services prerun" is active
03.31 209 Auxiliary services postrun
TRUE, if "Auxiliary services postrun" is active
Page 282/339
Woodward
Manual 37427
Logical Command Variables: Group 04: Applications Condition

Applications condition, Logic command variables 4.01-04.60
These operating statuses may be used as command variable in a logical output to set parameters for customized
operations.
No.
04.01
04.02
04.03
04.04
04.05
ID
239
240
241
242
243
Name
Auto mode
Stop mode
Manual mode
Lamp test
Acknowledge
04.06 244 GCB closed

04.07 245 MCB closed
04.09 247 Emergency mode
04.10 248 Cool down

04.11 249 Mains settling
04.12 250 Start w/o load
04.13 251 Remote request
04.14 252 Remote acknowledge
04.15 253 Idle run active
04.18 256 Synchron. GCB active
04.19 257 Opening GCB active
04.20 258 Closing GCB active
04.21 259 Syn. MCB is active
04.22 260 Opening MCB active
04.23 261 Closing MCB active
04.27 265 Critical mode
04.28 266 Generator unloading
04.29 267 Mains unloading
04.30 268 Power limited prerun
04.31 269 Segment no.2 act
Woodward
Function
AUTOMATIC operating mode active
STOP operating mode active
MANUAL operating mode active
A lamp test is being performed
"Acknowledge" push button has been
pressed or an external
acknowledgment via LogicsManager
GCB is closed {1oc} and {2oc}
MCB is closed {2oc} only
Emergency power operation active
Note
TRUE in AUTOMATIC operating mode
TRUE in STOP operating mode
TRUE in MANUAL operating mode
TRUE if the lamp test is active
This condition is TRUE for approx. 40 ms
and must be extended utilizing a delay time
TRUE if DI 8 (Reply GCB) is de-energized

TRUE if DI 7 (Reply MCB) is de-energized
TRUE with the expiration of the emergency
power delay; FALSE with the expiration of
the mains setting time and the reply from
the MCB is closed
Engine cool-down cycle active
TRUE as long as the cool down time is
running
Mains settling time active
Becomes TRUE with a mains failure and
FALSE after the mains settling timer has
expired
Start without closing GCB is active
TRUE if Start w/o load is enabled
Request over remote control to activate TRUE if the start bit is set via serial
a function
connection (Modbus) or CAN bus
(CANopen), (control word 503)
Request over remote control to
TRUE if this bit is set via interface (control
acknowledge
word 503)
Idle mode is active
TRUE if the idle mode is active. This may
be used to issue an "Idle" command to a
speed controller.
Synchronization GCB is active
TRUE if the GCB shall be synchronized
until the GCB is closed
Opening GCB is active
TRUE if a GCB open command is issued
until DI 8 (Reply GCB) is energized
Closing GCB is active
TRUE if a GCB close command is issued;
same function as relay 6 in {1oc} or {2oc}
Synchronization MCB is active
TRUE if the MCB shall be synchronized
until the MCB is closed
Opening MCB is active
TRUE if an MCB open command is issued
until DI 7 (Reply GCB) is energized
Closing MCB is active
TRUE if an MCB close command is issued;
same function as relay 8 in {2oc}
Critical mode operation is enabled
TRUE if critical mode is enabled
Generator unloading sequence is active TRUE if a stop command has been issued
until the GCB is opened
Mains unloading sequence is active
TRUE if a synchronization has been started
until the MCB is opened
Prerun operation with power limitation TRUE as long as the warm up load
is active
limitation is enabled
Load share group 2 is activated
Page 283/339
Manual 37427
No.
ID Name
04.34 272 LDSS Priority 2
04.37
04.38
04.39
04.40
04.41
04.43
04.44
04.45
04.46
04.47
04.48
04.49
04.50
04.51
04.52
04.53
04.54
04.55
04.56
04.57
04.58
04.59
04.60
275
276
277
278
279
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
Remote volt. setp. 2

Remote freq. setp. 2
Remote PF setp. 2
Remote pwr. setp. 2
Transition mode 1
LD start/stop
Interface Control 1
Interface Control 2
Interface Control 3
Interface Control 4
Interface Control 5
Interface Control 6
Interface Control 7
Interface Control 8
Interface Control 9
Interface Control 10
Crit. mode postrun
Function
Load-dependent start/stop priority 2 is
activated
activated
activated
Voltage set point 2 is enabled
Frequency set point 2 is enabled
Power factor set point 2 is enabled
Load set point 2 is enabled
Breaker transition mode alternative 1
Load-dependent start/stop is activated
Free control bit 1 is activated
Critical mode postrun is active
Note
TRUE if this bit is set via interface
(control word 504)
Refer to the Interface Manual 37430
TRUE as long as the critical mode

postrun time is running
Logical Command Variables: Group 05: Engine Related Alarms

Engine related alarms, Logic command variables 05.01-05.15
These engine alarms may be used as command variable in a logical output to set parameters for customized
operations.
No.
05.01
05.02
05.03
05.04
05.05
05.06
05.07
05.08
05.09
05.10
05.11
05.13
05.14
05.15
ID
299
300
301
302
303
304
305
306
307
308
309
311
312
313
Page 284/339
Name / Function
Overspeed (limit) 1
Overspeed (limit) 2
Underspeed (limit) 1
Underspeed (limit) 2
Unintended stop
Engine stop malfunction
Speed/frequency mismatch
Start fail
Maintenance days exceeded
Maintenance hours exceeded
Charge alternator low voltage
Red stop lamp
Amber warning lamp
EEprom failure
Note
TRUE = alarm latched (triggered)

FALSE = alarm acknowledged
Woodward
Manual 37427
Logical Command Variables: Group 06: Generator Related Alarms

Generator related alarms, Logic command variables 06.01-06.31
These generator alarms may be used as command variable in a logical output to set parameters for customized
operations.
No.
06.01
06.02
06.03
06.04
06.05
06.06
06.07
06.08
06.09
06.10
06.11
06.12
06.13
06.14
06.15
06.16
06.17
06.18
06.19
06.20
06.21
06.22
06.23
06.24
06.25
06.26
06.27
06.28
06.29
06.30
06.31
ID
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
Woodward
Name / Function
Generator overfrequency (limit) 1
Generator overfrequency (limit) 2
Generator underfrequency (limit) 1
Generator underfrequency (limit) 2
Generator overvoltage (limit) 1
Generator overvoltage (limit) 2
Generator undervoltage (limit) 1
Generator undervoltage (limit) 2
Generator (definite time) overcurrent (limit)1
Generator (definite time) overcurrent (limit) 2
Generator (definite time) overcurrent (limit) 3
Generator reverse/reduced power (limit) 1
Generator reverse/reduced power (limit) 2
Generator overload IOP (limit) 1
Generator overload IOP (limit) 2
(Generator) unbalanced load (limit)1
(Generator) unbalanced load (limit) 2
Generator (voltage) asymmetry
Ground fault (limit) 1
Ground fault (limit) 2
Generator mismatched phase rotation (rotation field alarm)
(Generator) inverse time-overcurrent
Generator overload MOP (limit) 1
Generator overload MOP (limit) 2
Generator power factor inductive (limit) 1
Generator power factor inductive (limit) 2
Generator power factor capacitive (limit) 1
Generator power factor capacitive (limit) 2
Generator active power ramp mismatch
Generator unloading mismatch
Out of operating range
Note

Page 285/339
Manual 37427
Logical Command Variables: Group 07: Mains Related Alarms

Mains related alarms, Logic command variables 07.01-07.25
These mains alarms may be used as command variable in a logical output to set parameters for customized
operations.
No.
07.05
07.06
07.07
07.08
07.09
07.10
07.11
07.12
07.13
07.14
07.16
07.25
ID
403
404
405
406
407
408
409
410
411
412
414
423
Function
Mains mismatched phase rotation (rotation field alarm)
Mains overfrequency (limit) 1
Mains overfrequency (limit) 2
Mains underfrequency (limit) 1
Mains underfrequency (limit) 2
Mains overvoltage (limit) 1
Mains overvoltage (limit) 2
Mains undervoltage (limit) 1
Mains undervoltage (limit) 2
Mains phase shift
Mains active power mismatch
Mains decoupling
Note
Logical Command Variables: Group 08: System Related Alarms

System related alarms, Logic command variables 08.01-08.33
These system alarms may be used as command variable in a logical output n to set parameters for customized
operations.
No.
08.01
08.02
08.03
08.04
08.05
08.06
08.07
08.08
08.10
08.16
08.17
08.18
08.19
08.20
08.30
08.31
08.33
ID
459
460
461
462
463
464
465
466
468
474
475
476
477
478
488
489
491
Page 286/339
Function
Battery overvoltage (limit) 1
Battery overvoltage (limit) 2
Battery undervoltage (limit) 1
Battery undervoltage (limit) 2
GCB fail to close
GCB fail to open
MCB fail to close
MCB fail to open
CAN J1939 communication alarm
Parameter alignment
Missing members
CANopen Interface 1
CANopen Interface 2
CAN bus overload
Timeout synchronization GCB
Timeout synchronization MCB
Generator /busbar / mains phase rotation mismatch
Note

Woodward
Manual 37427
Logical Command Variables: Group 09: Discrete Inputs

Discrete inputs, Logic command variables 09.01-09.12
The discrete inputs may be used as command variable in a logical output to set parameters for customized
operations.
No.
09.01
09.02
09.03
09.04
09.05
09.06
09.07
09.08
09.09
09.10
ID
519
520
521
522
523
524
525
526
527
528
Function
DI 1 (Discrete input [DI 01])
Note
TRUE = logical "1" (delay times and

NO/NC parameters are ignored)
FALSE = logical "0" (alarm has been
acknowledged or immediately after
TRUE condition is not present anymore,
if Control is configured as alarm class)
Logical Command Variables: Group 10: Analog Inputs

Analog inputs, Logic command variables 10.01-10.03
The analog inputs may be used as command variable in a logical output.
No.
10.01
10.02
10.03
10.04
ID
559
560
561
562
Name / Function
Analog input AI 01 wire break
Note
TRUE = measured value out of range
acknowledged, or immediately after
TRUE condition is not present anymore,
if Control is configured as alarm class)
Logical Command Variables: Group 11: Clock and Timer

Clock and timer, Logic command variables 11.01-11.10
Time functions may be used as command variable in a logical output.
No.
11.01
11.02
11.03
11.04
11.05
11.06
11.07
11.08
11.09
11.10
ID
579
580
581
582
583
584
585
586
587
588
Woodward
Name / Function
Timer set point 1 (exceeded)
Timer set point 2 (exceeded)
Active weekday (equal to setting)
Active day (equal to setting)
Active hour (equal to setting)
Active minute (equal to setting)
Active second (equal to setting)
Engine (running hours exceeded by) 1 hour
Note
see page 264
see page 264
see page 264
see page 264
see page 264
see page 264
see page 264
Status changes every operating hour
Status changes every 10 operating hours
Status changes every 100 operating hours
Page 287/339
Manual 37427
Logical Command Variables: Group 12: External Discrete Inputs 1

External discrete inputs 1, Logic command variables 12.01-12.16
Additional discrete inputs from an expansion board (i.e. IKD 1 extension board) may be used as command
variable in a logical output.
No.
12.01
12.02
12.03
12.04
12.05
12.06
12.07
12.08
12.09
12.10
12.11
12.12
12.13
12.14
12.15
12.16
ID
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
Name / Function
External discrete input 1 [D.E01]
Note
TRUE = logical "1" (delay times and NO/NC

parameters are ignored)
acknowledged, or immediately after TRUE
condition is not present anymore, if Control is
configured as alarm class)
Logical Command Variables: Group 13: Discrete Outputs

Discrete outputs, Logic command variables 13.01-13.12
The discrete outputs may be used as command variable in a logical output.
No.
13.01
13.02
13.03
13.04
13.05
13.06
13.07
13.08
13.09
13.10
13.11
ID
629
630
631
632
633
634
635
636
637
638
639
Page 288/339
Name / Function
Discrete output DO1 [R01]
Note
TRUE = logical "1" (this condition indicates the

logical status of the internal relays)
FALSE = logical "0" (this condition indicates
the logical status of the internal relays)
Woodward
Manual 37427
Logical Command Variables: Group 14: External Discrete Outputs 1

External discrete outputs 1, Logic command variables 14.01-14.16
The external discrete outputs may be used as command variable in a logical output.
No.
14.01
14.02
14.03
14.04
14.05
14.06
14.07
14.08
14.09
14.10
14.11
14.12
14.13
14.14
14.15
14.16
ID
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
Name / Function
External discrete output DO1 [R.E01]
Note
TRUE = logical "1" (this condition indicates the

logical status of the relays, which are connected via
external expansion boards)
FALSE = logical "0" (this condition indicates the
logical status of the relays, which are connected via
external expansion boards)
Logical Command Variables: Group 15: Flexible Limits

Flexible limits, Logic command variables 15.01-15.40
The flexible analog input thresholds may be used as command variable in a logical output.
No.
15.01
15.02
15.03
15.04
15.05
15.06
15.07
15.08
15.09
15.10
15.11
15.12
15.13
15.14
15.15
15.16
ID
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
Name / Function
Flexible analog input 1 (triggered)
Note
TRUE = limit value reached

Logical Command Variables: Group 18: Transistor Outputs

Transistor outputs, Logic command variables 18.01-18.04
The transistor outputs may be used as command variable in a logical output.
No.
18.05
ID
817
Woodward
Name / Function
Aux. Excit. active
Note
Page 289/339
Manual 37427
Factory Setting
The inputs, outputs, and internal flags, which may be programmed via the LogicsManager have the following
factory default settings when delivered:
simple (function)
extended (configuration)
result
Factory Setting: Functions

[00.0x] Flag {x}; {x} = 1 to 7
{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, flag {x} becomes TRUE.

Deactivated by default
FALSE
[00.08] Flag 8 - pre-configured to engine start via timer

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, flag 8 becomes TRUE.

TRUE once the configured time 1 has been
reached [11.01], and the configured time 2
[11.02] has not been reached as well if the
--- current day is the configured day [11.03] (see
page 264 "Configure LogicsManager: Set ")
--
dependent
on timer
[00.09] Start request in Auto

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the engine is started in

AUTOMATIC operating mode.
TRUE once discrete input [DI 2] is energized.
Note: This function is pre-configured and may
--- be activated by passing through the command
variables [00.08] LM: Flag 8 or [04.03]
--- Remote request ('' instead of '0').
Page 290/339
dependent
on [DI 2]
Woodward
Manual 37427
simple (function)
result
[00.10] Stop request in Auto

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the engine is either stopped in

AUTOMATIC operating mode or a start of
the engine is suppressed (also an emergency
operation).
--- Deactivated by default
FALSE
---
[00.11] Inhibit emergency run

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--- If TRUE, an emergency operation is inhibited

--- or interrupted.
FALSE
--
---
[00.12] Undelay close GCB

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--- If TRUE, the GCB will be closed in an

--- emergency operation without waiting for
--- expiration of the delayed engine monitoring.
TRUE once emergency mode is enabled.
--
dependent on
emergency
operation
[00.14] Constant Idle run

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Woodward
If TRUE, the control outputs an "Constant idle

run" if a start request for the generator is
present
FALSE
Page 291/339
Manual 37427
simple (function)
result
[00.15] External acknowledgment

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, all alarms are acknowledged from

an external source.
TRUE once discrete input [DI 5] is energized.
dependent on
discrete input
[DI 5]
[00.16] Operation mode AUTOMATIC

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE the unit changes into AUTOMATIC

operating mode.
FALSE
[00.17] Operation mode MANUAL

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE the unit changes into MANUAL

operating mode.
FALSE
[00.18] Operation mode STOP

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Page 292/339
If TRUE the unit changes into STOP

operating mode.
FALSE
Woodward
Manual 37427
simple (function)
result
[00.19] Start without load

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the engine is started without load

transfer to the generator (closing the GCB is
blocked).
FALSE
[00.20] Automatic Idle mode

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the control performs an idle run for

a configured time at start-up.
be activated by passing through the command
variable [00.09] Start req. in Auto ('' instead
of '0').
FALSE
[00.21] Raise frequency/load set point

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the frequency/load set point will be

raised.
FALSE
[00.22] Lower frequency/load set point

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Woodward
If TRUE, the frequency/load set point will be

lowered.
FALSE
Page 293/339
Manual 37427
simple (function)
result
[00.23] Raise voltage/power factor set point

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the voltage/power factor set point

will be raised.
FALSE
[00.24] Lower voltage/power factor set point

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the voltage/power factor set point

will be lowered.
FALSE
[00.25] Frequency droop active

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the frequency droop is enabled.

TRUE once missing members are detected on
the load share bus.
--
dependent
on missing
members
[00.26] Voltage droop active

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--
Page 294/339
If TRUE, the voltage droop is enabled.

TRUE once missing members are detected on
the load share bus.
dependent
on missing
members
Woodward
Manual 37427
simple (function)
result
[00.28] Critical mode

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the control performs a critical mode

operation.
TRUE, if no start failure is present and/or
--- discrete input [DI 1] is not energized.
---
dependent
on start
failure and
[DI 1]
[00.29] Firing speed reached

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the unit recognizes that the ignition

speed has been reached.
FALSE
[00.3x] Flag {y}; {x} = 0 to 5, {y} = 9 to 14

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
---
If TRUE, flag {y} becomes TRUE.

FALSE
---
Woodward
Page 295/339
Manual 37427
simple (function)
result
[00.36] Flag 15
{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN

Prepared for GCB fail to close or
Synchronization time GCB.
--
---
dependent
on GCB fail
to close and
Synchronizat
ion time
GCB
[00.37] Flag 16
{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--
---
Page 296/339

Prepared for Critical mode or Start without
load.
dependent
on Critical
mode and
Start without
load
Woodward
Manual 37427
simple (function)
result
[00.81] Setpoint 2 frequency enabled

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the frequency set point 2 is enabled.

FALSE
--
---
[00.82] Setpoint 2 load enabled

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the load set point 2 is enabled.

FALSE
--
---
[00.83] Setpoint 2 voltage enabled

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
---
If TRUE, the voltage set point 2 is enabled.

FALSE
---
Woodward
Page 297/339
Manual 37427
simple (function)
result
[00.84] Setpoint 2 power factor enabled

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
If TRUE, the power factor set point 2 is

enabled.
---
FALSE
---
[00.85] Enable MCB

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--- If TRUE, the MCB is enabled.

--- TRUE, if discrete input [DI 6] is energized
--- and/or MCB did not fail to close and/or no
mains phase rotation mismatch is detected.
--
---
dependent
on [DI 6]
and MCB
closure and
mains phase
rotation
[00.86] Load-dependent start/stop

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--- If TRUE, load-dependent start/stop is enabled.

-- Prepared for start request in AUTO and
--- neither Flag 15 nor Flag 16 are enabled.
FALSE
---
[00.8x] Segment no.{y} active; {x} = 7 to 9; {y} = 2 to 4

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--- If TRUE, load-dependent start/stop segment

--- no.{y} is enabled.
---
FALSE
---
Page 298/339
Woodward
Manual 37427
simple (function)
result
[00.9x] LDSS Priority {y}; {x} = 0 to 2; {y} = 2 to 4

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--- If TRUE, load-dependent start/stop priority

--- {y} is enabled.
---
FALSE
---
[00.9x] Transition mode {y}; {x} = 3 to 4; {y} = 1 to 2

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--- If TRUE, transition mode {x} is enabled.

--
---
FALSE
---
Woodward
Page 299/339
Manual 37427
simple (function)
result
Factory Setting: Relay Outputs

[00.41] Relay 1 [R01] - Ready for operation OFF
{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Relay will be de-energized if unit is not ready

for operation or the logics manager output is
TRUE.
be activated by passing through the command
variables [01.09] Shutdown alarm or [04.01]
Operating mode AUTO or [00.01] LM: Flag 1
('' instead of '0').
The unit is only ready for operation after an
start-up delay following the power supply
connection.
FALSE
[00.42] Relay 2 [R02] - Centralized alarm (horn) / freely configurable

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Relay energizes if the internal condition

"Horn" is TRUE
dependent on
Logics
Command
Variable
[03.05]
[00.43] Relay 3 [R03] - Starter / freely configurable

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN

"Starter" is TRUE
dependent on
Logics
Command
Variable
[03.02]
[00.44] Relay 4 [R04] - Start/Gas / freely configurable

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Page 300/339

"Start/Gas" is TRUE to energize the start
(Diesel) or gas (Gas) solenoid
dependent on
Logics
Command
Variable
[03.28]
Woodward
Manual 37427
simple (function)
result
[00.45] Relay 5 [R05] Command: open MCB / freely configurable

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--
In application mode
{0}, {1o} and {1oc} = freely configurable
relay (unassigned)
In application mode {2oc}
"Command: close MCB"
dependent on
application
mode or
Logics
Command
Variable
[01.08]
[00.46] Relay 6 [R06] - free / Command: close GCB

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
In application mode
{0} and {1o} = freely configurable relay
--- (unassigned)
-- In application mode {1oc} and {2oc}
"Command: close GCB"
FALSE
[00.47] Relay 7 [R07] - Mains decoupling / freely configurable / Command: open GCB
{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
In application mode {0} pre-configured to

--- mains decoupling. Relay energizes if the
--- internal condition "Mains decoupling" is
--- TRUE to decouple the genset from the mains.
In application mode
{1o}, {1oc}, and {2oc}
"Command: open GCB"
dependent on
application
mode and
Logics
Command
Variable
[07.25]
[00.48] Relay 8 [R08] - free / Command: close MCB
{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
--
Woodward
In application mode
{0}, {1o}, and {1oc} = freely configurable
relay (unassigned)
In application mode {2oc}
"Command: close MCB"
FALSE
Page 301/339
Manual 37427
simple (function)
result
[00.49] Relay 9 [R09] Stop solenoid / freely configurable

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Relay energizes if the internal condition "Stop

solenoid" is TRUE.
dependent on
Logics
Command
Variable
[03.27]
[00.50] Relay 10 [R10] - Auxiliary services / freely configurable

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Relay energizes if the internal condition "Aux.

services" is TRUE to activate the auxiliary
services (it energizes prior to an engine start
and de-energizes with the engine stop)
dependent on
Logics
Command
Variable
[03.01]
[00.51] Relay 11 [R11] - Shutdown alarm / freely configurable

{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Page 302/339

"Shutdown alarm" is TRUE.
dependent on
Logics
Command
Variable
[01.09]
Woodward
Manual 37427
simple (function)
result
[00.xx] External digital output {y} - free (external expansion card, if connected; {xx} = 63 to 78 ; {y} = 1 to 16)
{0}
{1o}
{1oc}
{2oc}
STOP
AUTO
MAN
Woodward
Control of the external relay {y}, if this is

connected
Prepared for:
FALSE
Page 303/339
Manual 37427
Discrete Inputs
[DI01]
{0}
{1o}
{1oc}
{2oc}
freely configurable, pre-assigned to

EMERGENCY STOP
alarm class F
[DI02]
{0}
{1o}
{1oc}
{2oc}

LogicsManager Start in AUTO
alarm class Control
[DI03]
{0}
{1o}
{1oc}
{2oc}

Low oil pressure
alarm class B
[DI04]
{0}
{1o}
{1oc}
{2oc}

Coolant temperature
alarm class B
[DI05]
{0}
{1o}
{1oc}
{2oc}

LogicsManager External acknowledgement
alarm class Control
[DI06]
{0}
{1o}
{1oc}
{2oc}

LogicsManager Enable MCB
alarm class Control
[DI07]
{0}
{1o}
{1oc}
{2oc}
Reply MCB (not available in the LogicsManager)
{0}
{1o}
{1oc}
{2oc}
Reply GCB (not available in the LogicsManager)
[DI09]
{0}
{1o}
{1oc}
{2oc}
freely configurable discrete input (unassigned)

alarm class B
[DI10]
{0}
{1o}
{1oc}
{2oc}
freely configurable discrete input (unassigned)

alarm class B
[DI08]
Page 304/339
Woodward
Manual 37427
Appendix C.
Analog Manager
To enhance flexibility of programming the functions of the easYgen-2000 Series, an analog manager is used. All
analog values, which are delivered by the easYgen may be used as data sources for the analog outputs (refer to
Configure Analog Outputs on page 171), the flexible limit monitoring (refer to Configure Monitoring: Flexible
Limits on page 120), and the controller set points (refer to Configure Application: Configure Controller on
page 215).
Every data source is indicated by a group number and a sub-number.
Some values are percentage values and relate to reference values.
Data Sources
Group 00: Internal Values

Analog
Data source
input #
00.01
Engine speed
00.02
Voltage bias
00.03
Speed bias
00.04
Battery voltage
00.05
Analog input D+ (auxiliary excitation)
00.06
Calculated ground current
00.07
Measured ground current
* Refer to parameter 1810 on page Fehler! Textmarke nicht definiert.
Woodward
Reference value
Rated speed
0 to 10000
0 to 10000
Battery voltage 24 V
Battery voltage 24 V
Ground current transformer ratio setting *
Page 305/339
Manual 37427
Group 01: Generator Values

Analog
input #
01.01
01.02
01.03
01.04
01.05
01.06
01.07
01.08
01.09
01.10
01.11
01.12
01.13
01.14
01.15
01.16
01.17
01.18
01.19
01.20
01.21
01.22
01.23
01.24
01.25
01.26
01.27
01.28
01.29
01.30
01.31
01.32
01.33
01.34
01.35
Data source
Reference value
Generator voltage wye average (phase-neutral)

Generator voltage L1-N
Generator voltage delta average (phase-phase)
Generator voltage L1-L2
Generator frequency
Generator frequency L1-L2
Generator current average
Generator current L1
Generator maximum current L1
Generator power factor
Generator power factor L1
Generator total real power
Generator real power L1-N
Generator total reactive power
Generator reactive power L1-N
Generator total apparent power
Generator apparent power L1-N

Rated frequency
Rated frequency
Rated frequency
Rated frequency
Power factor 1
Power factor 1
Power factor 1
Power factor 1
Generator rated real power
Generator rated real and reactive power
Group 02: Mains Values

Analog
input #
02.01
02.02
02.03
02.04
02.05
02.06
02.07
02.08
02.09
02.10
02.11
02.12
02.13
02.14
02.17
02.20
02.21
02.24
02.25
02.28
02.29
02.32
02.33
Data source
Reference value
Mains voltage wye average (phase-neutral)

Mains voltage L1-N
Mains voltage L2-N
Mains voltage L3-N
Mains voltage delta average (phase-phase)
Mains voltage L1-L2
Mains voltage L2-L3
Mains voltage L3-L1
Mains frequency
Mains frequency L1-L2
Mains current average
Mains current L1
Maximum mains current L1
Mains power factor
Mains power factor L1
Mains total power
Mains power L1-N
Mains total reactive power
Mains reactive power L1-N
Mains total apparent power
Mains apparent power L1-N
Mains rated voltage

Mains rated voltage
Mains rated voltage
Mains rated voltage
Mains rated voltage
Mains rated voltage
Mains rated voltage
Mains rated voltage
Rated frequency
Rated frequency
Rated frequency
Rated frequency
Mains rated current
Mains rated current
Mains rated current
Power factor 1
Power factor 1
Mains rated real power
Mains rated real power
Mains rated real and reactive power
Mains rated real and reactive power
Page 306/339
Woodward
Manual 37427
Group 05: Controller Set Points

Analog
input #
05.01
05.02
05.03
05.04
05.05
05.06
05.07
05.08
05.09
05.10
05.11
05.12
05.13
05.14
05.15
05.16
05.17
05.18
05.19
05.20
05.21
05.22
05.23
05.24
Data source
Reference value
Internal frequency set point 1

Internal frequency set point 2
Interface frequency set point
Internal power set point 1
Internal power set point 2
Interface power set point
Internal voltage set point 1
Internal voltage set point 2
Interface voltage set point
Internal power factor set point 1
Internal power factor set point 2
Interface power factor set point
Discrete f +/Discrete P +/Discrete V +/Discrete PF +/Used frequency setpoint
Used frequency setpoint ramp
Used power setpoint
Used power setpoint ramp
Used voltage setpoint
Used voltage setpoint ramp
Used PF setpoint
Used PF setpoint ramp
Group 06: DC Analog Input Values

Analog
Data source
input #
06.01
Analog input 1
06.02
Analog input 2
06.03
Analog input 3
06.04
Analog input 4
* Refer to Table 3-122 on page 307 for more information
Reference value
Display value format*
If the analog input type (parameter 1000 on page 160) is configured to VDO or Pt100, the following display
value formats apply:
Analog input type
Table A/B
Linear
Pt100
VDO 120C
VDO 150C
VDO 10 bar
VDO 5 bar
Off
Display value format

1%
1C
1C
1C
0.01 bar
0.01 bar
-
Example value
10%
453
103C
69C
73C
6.6 bar
5.0 bar
-
Example format
10
453
103
69
73
660
500
-
Table 3-122: Analog Manager - display value format
Woodward
Page 307/339
Manual 37427
Group 07: Engine Values

Analog
input #
07.01
07.02
07.03
07.04
07.05
07.06
07.07
07.08
07.09
07.10
07.11
07.12
07.13
07.14
07.15
07.16
07.17
07.18
07.19
07.20
07.21
07.22
07.23
07.24
07.25
07.26
07.27
07.28
07.29
07.30
07.31
07.32
07.33
07.34
07.35
07.36
07.37
07.38
07.39
07.40
07.41
07.42
07.43
07.44
07.45
07.46
07.47
07.48
07.49
07.50
07.51
07.52
07.53
07.54
07.55
07.56
07.57
07.58
07.59
07.60
07.61
07.62
07.63
07.64
07.65
07.66
07.67
Data source
Reference value
SPN 52: Engine Intercooler

SPN 91: Throttle Position
SPN 92: Load At Current Speed
SPN 94: Fuel Delivery Pressure
SPN 95: Fuel Filter Difference Pressure
SPN 98: Engine Oil Level
SPN 100: Engine Oil Pressure
SPN 101: Crankcase Pressure
SPN 102: Boost Pressure
SPN 105: Intake Manifold 1 Temperature
SPN 106: Turbo Air Inlet Pressure
SPN 107: Air Filter 1 Difference Pressure
SPN 108: Barometric Pressure
SPN 109: Coolant Pressure
SPN 110: Engine Coolant Temperature
SPN 111: Coolant Level
SPN 127: Transmission Oil Pressure
SPN 157: Fuel Rail Pressure
SPN 171: Ambient Air Temperature
SPN 172: Air Inlet Temperature
SPN 173: Exhaust Gas Temperature
SPN 174: Fuel Temperature
SPN 175: Engine Oil Temperature 1
SPN 176: Turbo Oil Temperature
SPN 177: Transmission Oil Temperature
SPN 183: Fuel Rate
SPN 190: Engine Speed
SPN 441: Auxiliary Temperature 1
SPN 442: Auxiliary Temperature 2
SPN 513: Actual Engine Torque
SPN 1122: Alternator Bearing 1 Temperature
SPN 1123: Alternator Bearing 2 Temperature
SPN 1124: Alternator Winding 1 Temperature
SPN 1134: Engine Thermostat
SPN 1135: Engine Oil Temperature 2
SPN 1136: Engine ECU Temperature
SPN 1137: Exhaust Gas Port 1 Temperature
SPN 1157: Main Bearing 1 Temperature
Page 308/339
Woodward
Manual 37427
Analog
input #
07.68
07.69
07.70
07.71
07.72
07.73
07.74
07.75
07.76
07.77
07.78
07.79
07.80
07.81
07.82
07.83
07.84
07.85
07.86
07.87
07.88
07.89
07.90
07.91
07.92
07.93
07.94
07.95
07.96
07.97
07.98
Data source

Reference value

SPN 1172: Turbo 1 Compressor Inlet Temperature
SPN 1176: Turbo 1 Compressor Inlet pressure
SPN 1180: Turbo 1 Inlet Temperature
SPN 1184: Turbo 1 Outlet Temperature
SPN 1203: Engine Auxiliary Coolant Pressure
SPN 1208: Pre-Filter Oil Pressure
SPN 1212: Engine Auxiliary Coolant Temperature
SPN 1382: Fuel Filter Difference Pressure
SPN 1800: Battery 1 Temperature
SPN 1801: Battery 2 Temperature
SPN 2433: Right Exhaust Gas Temperature
SPN 2434: Left Exhaust Gas Temperature
Woodward
Page 309/339
Manual 37427
Reference Values
NOTE
Refer to the Configure Analog Outputs section on page 171 for a description of the configuration
parameters for the analog output.
Refer to the Configure Monitoring: Flexible Limits section on page 119 for a description of the
configuration parameters for the flexible limits.
Generator Rated Voltage

All generator voltage values (wye, delta, and average values) refer to the generator rated voltage (parameter 1766
on page 38).
Analog output example:
The generator rated voltage (parameter 1766 on page 38) is configured to 400 V
The source value at maximum output is configured to 110.00% (of the rated voltage i.e. 440 V)
The source value at minimum output is configured to 10.00% (of the rated voltage i.e. 40 V)
The analog output range is configured to 0 to 20 mA
If a generator voltage of 40 V (or below) is measured, the analog output issues its lower limit (i.e. 0 mA)
If a generator voltage of 440 V (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a generator voltage of 240 V is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a generator voltage of 400 V is measured, the analog output issues 90 % of its upper limit (i.e. 18 mA)
Flexible limit example:
The generator rated voltage (parameter 1766 on page 38) is configured to 400 V
If the flexible limit is to be configured to 110.00% (of the rated voltage i.e. 440 V), it must be entered as 11000
Mains Rated Voltage

All mains voltage values (wye, delta, average, and peak values) refer to the mains rated voltage (parameter 1768
on page 38).
The mains rated voltage (parameter 1768 on page 38) is configured to 400 V
If a mains voltage of 40 V (or below) is measured, the analog output issues its lower limit (i.e. 0 mA)
If a mains voltage of 440 V (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a mains voltage of 240 V is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a mains voltage of 400 V is measured, the analog output issues 90 % of its upper limit (i.e. 18 mA)
The mains rated voltage (parameter 1768 on page 38) is configured to 400 V
Page 310/339
Woodward
Manual 37427
Rated Frequency
All frequency values (generator, mains, busbar 1) refer to the rated system frequency (parameter 1750 on
page 37).
The rated system frequency (parameter 1750 on page 37) is configured to 50 Hz
The source value at maximum output is configured to 110.00% (of the rated frequency i.e. 55 Hz)
The source value at minimum output is configured to 90.00% (of the rated frequency i.e. 45 Hz)
If a frequency of 45 Hz (or below) is measured, the analog output issues its lower limit (i.e. 0 mA)
If a frequency of 55 Hz (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a frequency of 50 Hz is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a frequency of 51 Hz is measured, the analog output issues 60 % of its upper limit (i.e. 12 mA)
The rated system frequency (parameter 1750 on page 37) is configured to 50 Hz
If the flexible limit is to be configured to 105.00% (of the rated frequency i.e. 52.5 Hz), it must be entered as
10500
Generator Rated Active Power

All generator active power values refer to the generator rated active power (parameter 1752 on page 38).
The generator rated active power (parameter 1752 on page 38) is configured to 500 kW
The source value at maximum output is configured to 120.00% (of the rated active power i.e. 600 kW)
The source value at minimum output is configured to 0.00% (of the rated active power i.e. 0 kW)
If an active power of 0 kW is measured, the analog output issues its lower limit (i.e. 0 mA)
If an active power of 600 kW (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If an active power of 300 kW is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If an active power of 120 kW is measured, the analog output issues 20 % of its upper limit (i.e. 4 mA)
If the flexible limit is to be configured to 120.00% (of the rated active power i.e. 600 kW), it must be entered as
12000
Woodward
Page 311/339
Manual 37427
Generator Rated Reactive Power

All generator reactive power values refer to the generator rated reactive power (parameter 1758 on page 38).
The generator rated reactive power (parameter 1758 on page 38) is configured to 500 kvar
The source value at maximum output is configured to 120.00% (of the rated reactive power i.e. 600 kvar)
The source value at minimum output is configured to 0.00% (of the rated reactive power i.e. 0 kvar)
If a reactive power of 0 kvar is measured, the analog output issues its lower limit (i.e. 0 mA)
If a reactive power of 600 kvar (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a reactive power of 300 kvar is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If the flexible limit is to be configured to 120.00% (of the rated reactive power i.e. 600 kvar), it must be entered
as 12000
NOTE
Above example is valid for inductive/lagging power. If capacitive/leading power is to be output, the
settings for the source value at min/max output must be negative.
Mains Rated Active Power

All mains active power values refer to the mains rated active power (parameter 1748 on page 38).
The mains rated active power (parameter 1748 on page 38) is configured to 500 kW
The source value at maximum output is configured to 120.00% (of the rated active power i.e. 600 kW)
The source value at minimum output is configured to 0.00% (of the rated active power i.e. 0 kW)
If a real power of 0 kW is measured, the analog output issues its lower limit (i.e. 0 mA)
If a real power of 600 kW (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a real power of 300 kW is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a real power of 120 kW is measured, the analog output issues 20 % of its upper limit (i.e. 4 mA)
If the flexible limit is to be configured to 120.00% (of the rated active power i.e. 600 kW), it must be entered as
12000
Page 312/339
Woodward
Manual 37427
Mains Rated Reactive Power

All mains reactive power values refer to the mains rated reactive power (parameter 1746 on page 39).
The mains rated reactive power (parameter 1746 on page 39) is configured to 500 kvar
The source value at maximum output is configured to 120.00% (of the rated reactive power i.e. 600 kvar)
The source value at minimum output is configured to 0.00% (of the rated reactive power i.e. 0 kvar)
If a reactive power of 0 kvar is measured, the analog output issues its lower limit (i.e. 0 mA)
If a reactive power of 600 kvar (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If the flexible limit is to be configured to 120.00% (of the rated reactive power i.e. 600 kvar), it must be entered
as 12000
Generator Rated Apparent Power

All generator apparent power values refer to the generator rated active power (parameter 1752 on page 38) and
generator rated reactive power (parameter 1758 on page 38). The generator rated apparent power S is calculated
using the real power P and the reactive power Q according to this formula: S = P + Q
The generator rated apparent power is 200 + 200 = 282.84 kVA
The source value at maximum output is configured to 120.00% (of the rated apparent power i.e. 339.41 kVA)
The source value at minimum output is configured to 0.00% (of the rated apparent power i.e. 0 kVA)
If an apparent power of 0 kVA is measured, the analog output issues its lower limit (i.e. 0 mA)
If an apparent power of 339.41 kVA (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If an apparent power of 169.71 kVA is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
The generator rated apparent power is 200 + 200 = 282.84 kVA
If the flexible limit is to be configured to 120.00% (of the rated apparent power i.e. 339.41 kVA), it must be
entered as 12000
Woodward
Page 313/339
Manual 37427
Mains Rated Apparent Power

All mains apparent power values refer to the mains rated active power (parameter 1748 on page 38) and mains
rated reactive power (parameter 1746 on page 39). The mains rated apparent power S is calculated using the real
power P and the reactive power Q according to this formula: S = P + Q
The mains rated apparent power is 200 + 200 = 282.84 kVA
The source value at maximum output is configured to 120.00% (of the rated apparent power i.e. 339.41 kVA)
The source value at minimum output is configured to 0.00% (of the rated apparent power i.e. 0 kVA)
If an apparent power of 0 kVA is measured, the analog output issues its lower limit (i.e. 0 mA)
If an apparent power of 339.41 kVA (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
The mains rated apparent power is 200 + 200 = 282.84 kVA
If the flexible limit is to be configured to 120.00% (of the rated apparent power i.e. 339.41 kVA), it must be
entered as 12000
Page 314/339
Woodward
Manual 37427
Generator / Mains Power Factor

The power factor is scaled linear over a range from 0001 to 9999 according to the following:
Power factor leading 0.01 corresponds with a value of 0001 (i.e. 00.01% of the value range)
Power factor
1.00 corresponds with a value of 5000 (i.e. 50.00% of the value range)
Power factor lagging 0.80 corresponds with a value of 6000 (i.e. 60.00% of the value range)
Value
0001
2500
4000 4500
PF
0.01
Leading
0.50
(capacitive)
0.80 0.90
Flexible limits:
5000
1.00
5500 6000
7500
0.90 0.80
0.50
overrun
9999
Lagging
(inductive)
0.01
underrun
Figure 3-35: Reference values - power factor scaling

The source value at maximum output is configured to 10000
The source value at minimum output is configured to 00000
If a power factor of leading 0.8 is measured, the analog output issues 40% of its upper limit (i.e. 8 mA)
If a power factor of leading 1 is measured, the analog output issues 50% of its upper limit (i.e. 10 mA)
If a power factor of lagging 0.9 is measured, the analog output issues 55% of its upper limit (i.e. 11 mA)
If a power factor of leading 0.95 is measured, the issued value is 4750
If a power factor of leading 1 is measured, the issued value is 5000
If a power factor of lagging 0.8 is measured, the issued value is 6000
Woodward
Page 315/339
Manual 37427
Generator Rated Current

All generator current values (line, average, and peak values) refer to the generator rated current (parameter 1754
on page 38).
The generator rated current (parameter 1754 on page 38) is configured to 1000 A
The source value at maximum output is configured to 110.00% (of the rated current i.e. 1100 A)
The source value at minimum output is configured to 10.00% (of the rated current i.e. 100 A)
If a generator current of 100 A (or below) is measured, the analog output issues its lower limit (i.e. 0 mA)
If a generator current of 1100 A (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a generator current of 600 A is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a generator current of 300 A is measured, the analog output issues 20 % of its upper limit (i.e. 4 mA)
The generator rated current (parameter 1754 on page 38) is configured to 1000 A
If the flexible limit is to be configured to 110.00% (of the rated current i.e. 1100 A), it must be entered as 11000
Mains Rated Current

All mains current values (line, average, and peak values) refer to the mains rated current (parameter 1785 on
page 39).
The mains rated current (parameter 1785 on page 39) is configured to 1000 A
The source value at maximum output is configured to 110.00% (of the rated current i.e. 1100 A)
The source value at minimum output is configured to 10.00% (of the rated current i.e. 100 A)
If a mains current of 100 A (or below) is measured, the analog output issues its lower limit (i.e. 0 mA)
If a mains current of 1100 A (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a mains current of 600 A is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a mains current of 300 A is measured, the analog output issues 20 % of its upper limit (i.e. 4 mA)
The mains rated current (parameter 1785 on page 39) is configured to 1000 A
If the flexible limit is to be configured to 110.00% (of the rated current i.e. 1100 A), it must be entered as 11000
Rated Speed
The measured speed refers to the rated speed (parameter 1601 on page 37).
The rated speed (parameter 1601 on page 37) is configured to 1500 rpm
The source value at maximum output is configured to 120.00% (of the rated speed i.e. 1800 rpm)
The source value at minimum output is configured to 0.00% (of the rated speed i.e. 0 rpm)
If a speed of 0 rpm is measured, the analog output issues its lower limit (i.e. 0 mA)
If a speed of 1800 rpm (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a speed of 900 rpm is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a speed of 1500 rpm is measured, the analog output issues ~83 % of its upper limit (i.e. 16.7 mA)
The rated speed (parameter 1601 on page 37) is configured to 1500 rpm
If the flexible limit is to be configured to 120.00% (of the rated speed i.e. 1800 rpm), it must be entered as 12000
Page 316/339
Woodward
Manual 37427
Battery Voltage
The measured battery and auxiliary excitation voltage refer to the fix rated battery voltage of 24 V.
The source value at maximum output is configured to 120.00% (of the rated voltage i.e. 28.8 V)
The source value at minimum output is configured to 20.00% (of the rated voltage i.e. 4.8 V)
If a battery voltage of 4.8 V (or below) is measured, the analog output issues its lower limit (i.e. 0 mA)
If a battery voltage of 28.8 V (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a battery voltage of 16.8 V is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a battery voltage of 24 V is measured, the analog output issues 80 % of its upper limit (i.e. 16 mA)
If the flexible limit is to be configured to 120.00% (of the rated voltage i.e. 28.8 V), it must be entered as 12000
Busbar 1 Rated Voltage

The busbar 1 delta voltage values refer to the busbar 1 rated voltage (parameter 1781 on page 38).
The busbar 1 rated voltage (parameter 1781 on page 38) is configured to 400 V
If a busbar 1 voltage of 40 V (or below) is measured, the analog output issues its lower limit (i.e. 0 mA)
If a busbar 1 voltage of 440 V (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a busbar 1 voltage of 240 V is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a busbar 1 voltage of 400 V is measured, the analog output issues 90 % of its upper limit (i.e. 18 mA)
The busbar 1 rated voltage (parameter 1781 on page 38) is configured to 400 V
Display Value Format

The analog input values refer to the display value format (refer to parameter 1035 on page 165). Delimiters like
decimal points or commas are ignored. If the display value format is 0.01 bar for example, a value of 5 bar
corresponds with 00500.
An analog input is configured to VDO 120C characteristic.
The source value at maximum output is configured to 00100 (i.e. 100C)
The source value at minimum output is configured to 00020 (i.e. 20C)
If a value of 20C (or below) is measured, the analog output issues its lower limit (i.e. 0 mA)
If a value of 100C (or above) is measured, the analog output issues its upper limit (i.e. 20 mA)
If a value of 60C is measured, the analog output issues 50 % of its upper limit (i.e. 10 mA)
If a value of 84C is measured, the analog output issues 80 % of its upper limit (i.e. 16 mA)
An analog input is configured to VDO 10 bar characteristic.
If the flexible limit is to be configured to 5.23 bar, it must be entered as 00523
Note: Refer to Table 3-122 on page 307 for more information on the fixed display value formats.
Woodward
Page 317/339
Manual 37427
Appendix D.
Event History
The event history is a 300-entry FIFO (First In/First Out) memory for logging alarm events and operation states
of the unit. As new event messages are entered into the history, the oldest messages are deleted once 300 events
have occurred. Refer to the Operation Manual 37428 for additional information about the event history.
Resetting the Event History

NOTE
Be sure to be in the appropriate code level to reset the event history. If you have not entered the
correct password for the required code level, the parameters for resetting the event history are not
available (refer to the System Management section on page 32 for more information).
The event history can be reset using the parameter "Clear event log" via the front panel.
Resetting the Event History Using the Front Panel
Make sure that you are in code level CL2 or higher (refer to the Enter Password section on page 30 ).
Set the parameter "Clear event log" to Yes (refer to the System Management section on page 32).
The complete event history is now being cleared.
Event List
Index
14353
14354
14355
14700
14701
14702
14703
14704
14705
14706
14707
English event text

AUTO mode
STOP mode
MAN mode
MCB open
MCB close
GCB open
GCB close
Mains failure
Emergency run
Engine is running
Critical mode
German event text

BAW AUTO
BAW STOP
BAW HAND
NLS AUF
NLS ZU
GLS AUF
GLS ZU
Netzausfall
Notstrombetrieb
Aggregat luft
Sprinklerbetrieb
Description
Auto mode
Stop mode
Manual mode
MCB open
MCB close
GCB open
GCB close
Mains failure
Emergency run
Engine is running
Critical mode
Table 3-123: Event history - event list
Alarm List
Index
1714
1912
1913
1962
1963
2012
2013
2062
2063
2112
2113
2162
2163
2218
2219
2220
2262
2263
2314
2315
2337
English event text

EEPROM failure
Gen. overfrequency 1
Gen. overfrequency 2
Gen.underfrequency 1
Gen.underfrequency 2
Gen. overvoltage 1
Gen. overvoltage 2
Gen. undervoltage 1
Gen. undervoltage 2
Overspeed 1
Overspeed 2
Underspeed 1
Underspeed 2
Gen. overcurrent 1
Gen. overcurrent 2
Gen. overcurrent 3
Gen. rev./red. pwr.1
Gen. rev./red. pwr.2
Gen. overload IOP 1
Gen. overload IOP 2
Gen. PF lagging 1
Page 318/339
German event text

EEPROM Fehler
Gen.berfrequenz 1
Gen.berfrequenz 2
Gen.Unterfrequenz 1
Gen.Unterfrequenz 2
Gen.berspannung 1
Gen.berspannung 2
Gen.Unterspannung 1
Gen.Unterspannung 2
berdrehzahl 1
berdrehzahl 2
Unterdrehzahl 1
Unterdrehzahl 2
Gen.berstrom 1
Gen.berstrom 2
Gen.berstrom 3
Gen.Rck/Minderlast1
Gen.Rck/Minderlast2
Gen. berlast IPB 1
Gen. berlast IPB 2
Gen. cos.phi ind. 1
Description
Internal error. EEPROM checksum corrupted.
Alarm overfrequency generator threshold 1
Alarm overfrequency generator threshold 2
Alarm underfrequency generator threshold 1
Alarm underfrequency generator threshold 2
Alarm overvoltage generator threshold 1
Alarm overvoltage generator threshold 2
Alarm undervoltage generator threshold 1
Alarm undervoltage generator threshold 2
Alarm engine overspeed threshold 1
Alarm engine overspeed threshold 2
Alarm engine underspeed threshold 1
Alarm engine underspeed threshold 2
Alarm overcurrent generator threshold 1
Alarm reverse/reduced power generator threshold 1
Alarm reverse/reduced power generator threshold 2
Alarm overload generator IOP threshold 1
Alarm overload generator IOP threshold 2
Monitoring generator power factor on exceeding a power factor limit
1. Alarm generator power factor lagging threshold 1.
Woodward
Manual 37427
Index
2338
English event text

Gen. PF lagging 2
German event text

Gen. cos.phi ind. 2
2362
2363
2387
Gen. overload MOP 1

Gen. overload MOP 2
Gen. PF leading 1
Gen. berlast NPB 1

Gen. berlast NPB 2
Gen. cos.phi kap. 1
2388
Gen. PF leading 2
Gen. cos.phi kap. 2
2412
2413
2457
Unbalanced load 1
Unbalanced load 2
Speed/freq. mismatch
Schieflast 1
Schieflast 2
Alarm Drehz.erkenng.
2504
2560
2561
2603
2604
2623
2624
2652
2664
2862
2863
2912
2913
2924
2934
2944
2962
2963
2985
Eng. stop malfunct.

Maint. days exceeded
Maint. hrs exceeded
GCB fail to close
GCB fail to open
MCB fail to close
MCB fail to open
Unintended stop
Operat. range failed
Mains overfreq. 1
Mains overfreq. 2
Mains underfreq. 1
Mains underfreq. 2
Gen act.pwr mismatch
Mns act.pwr mismatch
Ph.rotation mismatch
Mains overvoltage 1
Mains overvoltage 2
Mains PF lagging 1
Abstellstrung
Wartungstage abgel.
Wartungsstd. abgel.
GLS ZU Strung
GLS AUF Strung
NLS ZU Strung
NLS AUF Strung
Ungewollter Stop
Arbeitsber. verfehlt
Netz berfrequenz 1
Netz berfrequenz 2
Netz Unterfrequenz 1
Netz Unterfrequenz 2
Abweichg. Gen.Wirkl.
Abweichg. Netzwirkl.
Drehfeldfehler
Netz berspannung 1
Netz berspannung 2
Netz cos.phi ind. 1
2986
Mains PF lagging 2
Netz cos.phi ind. 2
3012
3013
3035
Mains undervoltage 1
Mains undervoltage 2
Mains PF leading 1
Netz Unterspannung 1
Netz Unterspannung 2
Netz cos.phi kap. 1
3036
Mains PF leading 2
Netz cos.phi kap. 2
3057
3064
3074
3114
Mains phase shift

GCB syn. timeout
MCB syn. timeout
Mains decoupling
Netz Phasensprung
GLS Synchron. Zeit
NLS Synchron. Zeit
Netzentkopplung
3124
Gen. unloading fault
Gen. Abschaltlstg.
3217
3218
3241
3242
3263
3264
3325
3907
3955
3975
4038
4056
4064
4073
10005
10006
10007
10008
10014
10015
10017
10018
10019
10020
10021
Mains import power 1

Mains import power 2
Mains export power 1
Mains export power 2
Ground fault 1
Ground fault 2
Start fail
Gen. volt. asymmetry
Gen.ph.rot. mismatch
Mns.ph.rot. mismatch
Inv. time overcurr.
Charge alt. low volt
Missing members
Parameter alignment
Bat. undervoltage 1
Bat. undervoltage 2
Bat. overvoltage 1
Bat. overvoltage 2
Wb:Analog input 1
Wb:Analog input 2
CAN fault J1939
Flexible limit 1
Flexible limit 2
Flexible limit 3
Flexible limit 4
Netz Bezugslstg. 1
Netz Bezugslstg. 2
Netz Lieferlstg. 1
Netz Lieferlstg. 2
Erdschlu 1
Erdschlu 2
Startfehler
Gen. Spg. Asymmetrie
Gen. Drehfeld Fehler
Netz Drehfeld Fehler
berstrom AMZ
Lichtm. Unterspg.
Anzahl Teilnehmer
Parameterabgleich
Bat. Unterspannung 1
Bat. Unterspannung 2
Bat. berspannung 1
Bat. berspannung 2
Db:Analogeingang 1
Db:Analogeingang 2
CAN Fehler J1939
Flexibler Grenzwert 1
Woodward
Description
Monitoring generator power factor on exceeding a power factor limit
2. Alarm generator power factor lagging threshold 2.
Alarm overload generator MOP threshold 1
Alarm overload generator MOP threshold 2
Monitoring generator power factor on fall below a power factor limit
1. Alarm generator power factor leading threshold 1.
Monitoring generator power factor on fall below a power factor limit
2. Alarm generator power factor leading threshold 2.
Alarm generator unbalanced load threshold 1
Alarm generator unbalanced load threshold 2
Alarm speed detection implausible (generator frequency, pickup, DI
are not matching)
Alarm shutdown malfunction
Alarm maintenance days overdue
Alarm maintenance hours overdue
Alarm failed to close GCB
Alarm failed to open GCB
Alarm failed to close MCB
Alarm failed to open MCB
Alarm unintended stop
Alarm operating range failed monitoring
Alarm mains overfrequency threshold 1 (for mains decoupling)
Alarm mains overfrequency threshold 2 (for mains decoupling)
Alarm mains underfrequency threshold 1 (for mains decoupling)
Alarm mains underfrequency threshold 2 (for mains decoupling)
Alarm generator active power mismatch
Alarm mains active power mismatch
Alarm phase rotation mismatch
Alarm mains overvoltage threshold 1 (for mains decoupling)
Alarm mains overvoltage threshold 2 (for mains decoupling)
Monitoring mains power factor on exceeding a power factor limit 1.
Alarm mains power factor lagging threshold 1.
Monitoring mains power factor on exceeding a power factor limit 2.
Alarm mains power factor lagging threshold 2.
Alarm mains undervoltage threshold 1 (for mains decoupling)
Alarm mains undervoltage threshold 2 (for mains decoupling)
Monitoring mains power factor on fall below a power factor limit 1.
Alarm mains power factor leading threshold 1.
Monitoring mains power factor on fall below a power factor limit 2.
Alarm mains power factor leading threshold 2.
Alarm mains phase shift for mains decoupling
Alarm timeout synchronization GCB
Alarm timeout synchronization MCB
Alarm mains decoupling triggered. The mains decoupling function
has recognized a mains failure and tripped the breaker.
Alarm generator unloading fault. It was not possible to unload the
generator within the configurable time.
Alarm mains import power threshold 1
Alarm mains import power threshold 2
Alarm mains export power threshold 1
Alarm mains export power threshold 2
Alarm ground fault threshold 1
Alarm ground fault threshold 2
Alarm start fail
Alarm generator voltage asymmetry alarm message
Alarm generator phase rotation miswired
Alarm mains phase rotation miswired
Alarm generator inverse time overcurrent
Alarm battery charge fail monitoring
Number of load share participants does not match
Load share participants are not all configured identically
Alarm battery undervoltage level 1
Alarm battery undervoltage level 2
Alarm battery overvoltage level 1
Alarm battery overvoltage level 2
Analog input1 wire break or short circuit ( configurable )
Analog input2 wire break or short circuit ( configurable )
Alarm message: CAN-Error J1939
Alarm flexible limit 1 (configurable)
Page 319/339
Manual 37427
Index
10022
10023
10024
10025
10026
10027
10028
10029
10030
10031
10032
10033
10060
10087
10088
10089
10600
10601
10602
10603
10604
10605
10607
10608
10609
10610
15125
15126
16360
16361
16362
16364
16365
16366
16367
16368
16369
16370
16371
16372
16373
16374
16375
16376
English event text

Flexible limit 5
Flexible limit 6
Flexible limit 7
Flexible limit 8
Flexible limit 9
Flexible limit 10
Flexible limit 11
Flexible limit 12
Flexible limit 13
Flexible limit 14
Flexible limit 15
Flexible limit 16
Wb:Analog input 3
CANopen Interface 1
CANopen Interface 2
CAN bus overload
Discrete input 1
Discrete input 2
Discrete input 3
Discrete input 4
Discrete input 5
Discrete input 6
Discrete input 7
Discrete input 8
Discrete input 9
Discrete input 10
Red stop lamp
Amber warning lamp
Ext. Discrete input 1

German event text
Db:Analogeingang 3
CANopen Interface 1
CANopen Interface 2
CAN-Bus berlast
Digitaleingang 1
Digitaleingang 2
Digitaleingang 3
Digitaleingang 4
Digitaleingang 5
Digitaleingang 6
Digitaleingang 7
Digitaleingang 8
Digitaleingang 9
Digitaleingang 10
Rote Stoplampe
Gelbe Warnlampe
Ext. Digitaleingang 1
Description
Wire break or short circuit at analog input 3
No data received on CAN bus 1
No data received on CAN bus 2
Too much messages on all CAN buses
Alarm DI1 (configurable)
Alarm DI7
Alarm DI8
Red lamp alarm of J1939
Amber lamp alarm of J1939
Alarm external DI1 (configurable)
Table 3-124: Event history - alarm list
Page 320/339
Woodward
Manual 37427
Appendix E.
Triggering Characteristics
Time-Dependent Overshoot Monitoring
This triggering characteristic is used for time-dependent overcurrent monitoring.
IRated [%]
SP1 < SP2 < SP3

t[SP1] > t[SP2] > t[SP3]
SP3 [%/IRated]
Protected Area
SP2 [%/IRated]
SP1 [%/IRated]
t[SP3]
t[SP2]
t[SP1]
t [s]
Figure 3-36: Triggering characteristics - three-level time-dependent overshoot montitoring
Woodward
Page 321/339
Manual 37427
Two-Level Overshoot Monitoring
This triggering characteristic is used for generator, mains & battery overvoltage, generator & mains
overfrequency, overload IOP & MOP, and engine overspeed monitoring.
t[min-SP2]
t[min-SP1]
t[min-SP2]
t[min-SP1]
t[min-SP1]
(Alarm limit 2)
Alarm SP 2
(Alarm limit 1)
Alarm SP 1
Monitoring
active
Minimum
Rated value
[100 %]
SP1
SP1Hysteresis
SP2
SP2Hysteresis
[%]
t[min-SP1]
Figure 3-37: Triggering characteristics - two-level overshoot montitoring

Page 322/339
Woodward
Manual 37427
Two-Level Undershoot Monitoring
This triggering characteristic is used for generator, mains & battery undervoltage, generator & mains
underfrequency, and engine underspeed monitoring.
t[min-SP2]
t[min-SP1]
t[min-SP2]
t[min-SP1]
t[min-SP1]
Alarm SP 2
(Alarm limit 2)
(Alarm limit 1)
Alarm SP 1
Monitoring
active
Minimum
SP2
SP2Hysteresis
SP1
SP1Hysteresis
Rated value
[100 %]
[%]
t[min-SP1]
Figure 3-38: Triggering characteristics - two-level undershoot montitoring

Woodward
Page 323/339
Manual 37427
Two-Level Reversed/Reduced Load Monitoring
t [s]
t [s]
t [s]
t [s]
This triggering characteristic is used for generator reversed/reduced load monitoring.
t[min-SPrev
t[min-SPred]
t[min-SPrev]
t[min-SPred]
t[min-SPred]
(Alarm limit 2)
Alarm SP 2
(Alarm limit 1)
Alarm SP 1
Monitoring
active
SPrev
SPrevHysteresis
[0 %]
SPred
SPredHysteresis
Minimum
Rated value
[100 %]
[%]
t[min-SPred]
Figure 3-39: Triggering characteristics - two-level reversed/reduced load montitoring
Page 324/339
Woodward
Manual 37427
Two-Level Unbalanced Load Monitoring
This triggering characteristic is used for generator unbalanced load monitoring.
t[min-SP2]
t[min-SP1]
t[min-SP2]
t[min-SP1]
t[min-SP1]
(Alarm limit 2)
Alarm SP 2
(Alarm limit 1)
Alarm SP1
Monitoring
active
Minimum
Average value
Limit 1
Limit 1 Hysteresis
Limit 2
Limit 2 Hysteresis
t[min-SP1]
Figure 3-40: Triggering characteristics - two-level unbalanced load montitoring
Woodward
Page 325/339
Manual 37427
One-Level Asymmetry Monitoring
This triggering characteristic is used for generator voltage asymmetry monitoring.
t[min-SP]
t[min-SP]
t[min-SP]
(Alarm limit)
Alarm
Monitoring
active
Minimum
Average value
Limit
Limit Hysteresis
t[min-SP]
Figure 3-41: Triggering characteristics - one-level asymmetry montitoring

Page 326/339
Woodward
Manual 37427
Appendix F.
Characteristics Of The VDO Inputs
Since VDO sensors are available in various different types, the Index Numbers of the characteristic curve tables
are listed. The customer must observe to order a sensor with the correct characteristic curve when selecting a
VDO sensor. Manufacturers of VDO sensors usually list these tables in their catalogs.
VDO Input "Pressure" (0 to 5 bar / 0 to 72 psi) - Index "III"
VDO Pres. 0-5 bar Index "III"

200
180
160
140
R [Ohm]
120
100
80
60
40
20
0
0
0.5
1.5
2.5
3.5
4.5
P [bar]
Figure 3-42: Analog inputs - characteristics diagram VDO 0 to 5 bar, Index "III"
P [bar]
P [psi}
R [Ohm]
0
0
11
0.5
7.25
29
1
14.50
47
1.5
21.76
65
2
29.00
82
2.5
36.26
100
3
43.51
117
3.5
50.76
134
4
58.02
151
4.5
65.27
167
5
72.52
184
Table 3-125: Analog inputs - characteristics diagram VDO 0 to 5 bar, Index "III"
Woodward
Page 327/339
Manual 37427
VDO Input "Pressure" (0 to 10 bar / 0 to 145 psi) - Index "IV"
VDO Pres. 0-10 bar Index "IV"

200
180
160
140
R [Ohm]
120
100
80
60
40
20
0
0
10
P [bar]
Figure 3-43: Analog inputs - characteristics diagram VDO 0 to 10 bar, Index "IV"
P [bar]
P [psi}
R [Ohm]
0
0
10
0.5
7.25
21
1
14.50
31
1.5
21.76
42
2
29.00
52
3
43.51
71
4
58.02
90
5
72.52
107
6
7
8
8.5
9
10
87.02 101.53 116.03 123.28 130.53 145.04
124
140
156
163
170
184
Table 3-126: Analog inputs - characteristics diagram VDO 0 to 10 bar, Index "IV"
Page 328/339
Woodward
Manual 37427
VDO Input "Temperature" (40 to 120 C / 104 to 248 F)

- Index "92-027-004"
VDO Temp. 40-120 C 92-027-004

400
350
300
R [Ohm]
250
200
150
100
50
0
35
40
45
50
55
60
65
70
75
80
85
90
95
100
105
110
115
120
125
Temp. [C]
Figure 3-44: Analog inputs - characteristics diagram VDO 40 to 120 C, Index "92-027-004"
Temp. [C]
Temp. [F}
40
104
291.46
45
113
239.56
50
122
197.29
55
131
161.46
60
140
134.03
65
149
113.96
70
158
97.05
75
167
82.36
Temp. [C]
Temp. [F}
85
185
59.73
90
194
51.21
95
203
44.32
100
212
38.47
105
221
33.40
110
230
29.12
115
239
25.53
120
248
22.44
R [Ohm]
R [Ohm]
80
176
70.12
Table 3-127: Analog inputs - characteristics diagram VDO 40 to 120 C, Index "92-027-004"
Woodward
Page 329/339
Manual 37427
VDO Input "Temperature" (50 to 150 C / 122 to 302 F)

- Index "92-027-006"
VDO Temp. 50-150 C 92-027-006

400
350
300
R [Ohm]
250
200
150
100
50
0
45
50
55
60
65
70
75
80
85
90
95
100 105 110 115 120 125 130 135 140 145 150 155
Temp. [C]
Figure 3-45: Analog inputs - characteristics diagram VDO 50 to 150 C, Index "92-027-006"
Temp. [C]
Temp. [F}
50
122
322.17
55
131
266.19
60
140
221.17
65
149
184.72
70
158
155.29
75
167
131.38
80
176
112.08
85
185
96.40
90
194
82.96
95
203
71.44
Temp. [C]
Temp. [F}
105
221
54.01
110
230
47.24
115
239
41.42
120
248
36.51
125
257
32.38
130
266
28.81
135
275
25.70
140
284
23.00
145
293
20.66
150
302
18.59
R [Ohm]
R [Ohm]
100
212
61.92
Table 3-128: Analog inputs - characteristics diagram VDO 50 to 150 C, Index "92-027-006"
Page 330/339
Woodward
Manual 37427
Pt100 RTD
Figure 3-46: Analog inputs - characteristics diagram Pt100

Temp. [C]
Temp. [F}
-200
-328
18.5
-150
-238
39.7
-100
-148
60.25
-50
-58
80.7
0
32
100
10
50
103.9
20
68
107.8
30
86
111.7
40
104
115.5
50
122
119.4
60
140
123.2
Temp. [C]
Temp. [F}
70
158
127.1
80
176
130.9
90
194
134.7
100
212
138.5
125
257
147.9
150
302
157.3
175
347
166.6
200
392
175.8
225
437
188.6
250
482
194.1
300
572
212.0
Temp. [C]
Temp. [F}
350
662
229.7
400
752
247.0
450
842
264.1
500
932
280.9
550
1022
297.4
600
1112
313.6
650
1202
329.5
700
1292
345.1
750
1382
360.5
800
1472
375.5
850
1562
390.25
R [Ohm]
R [Ohm]
R [Ohm]
Table 3-129: Analog inputs - characteristics diagram Pt100
Woodward
Page 331/339
Manual 37427
Appendix G.
LDSS Formulas
The following formulas are used by the load-dependent start/stop function to determine whether a genset is to be
started or stopped.
Abbreviations
PGN real active

Prated active
Preserve
Preserve isolated
Physteresis IOP
PMN setpoint
PMN real
PMOP minimum
Preserve parallel
Physteresis MOP
Pmax. load isolated
Pmin. load isolated
Pmax. load parallel
Pmin. load parallel
Momentary active generator real power on the busbar

Momentary active generator rated power on the busbar
Prated active PGN real active
Parameter 5760; minimum permissible reserve power on busbar in isolated operation
Parameter 5761; hysteresis in isolated operation
Export / import power control setpoint
Momentary active power at the interchange point
Parameter 5767; minimum requested generator load
Parameter 5768; minimum permissible reserve power on busbar in mains parallel operation
Parameter 5769; hysteresis in mains parallel operation
Parameter 5762; maximum permissible generator load in isolated operation
Parameter 5763; minimum permissible generator load in isolated operation
Parameter 5770; maximum permissible generator load in mains parallel operation
Parameter 5771; minimum permissible generator load in mains parallel operation
LDSS Mode Reserve Power
Isolated Operation
Changing the Engine Combination to Increase Rated Power
PGN real active + Preserve isolated > Prated active
Changing the Engine Combination to Reduce Rated Power
PGN real active + Preserve isolated + Physteresis IOP < Prated active
Mains Parallel Operation (Import/Export Control)

Starting the First Engine Combination (no engine supplies the busbar)
PMN setpoint PMN real + PGN real active > PMOP minimum
PMN setpoint PMN real + PGN real active + Preserve parallel > Prated active
Changing the Engine Combination to Reduce Rated Power
PMN setpoint PMN real + PGN real active + Preserve parallel + Physteresis MOP < Prated active
Stopping the Last Engine Combination (load close to minimum load)
Page 332/339
Woodward
Manual 37427
LDSS Mode Generator Load
Isolated Operation
PGN real active > Pmax. load isolated
Changing the Engine Combination to Reduce Rated Power (except dynamic set point is not
matched)
PGN real active < Pmin. load isolated
Mains Parallel Operation (Import/Export Control)

Starting the First Engine Combination (no engine supplies the busbar)
PMN setpoint PMN real + PGN real active > PMOP minimum
PGN real active > Pmax. load parallel
Changing the Engine Combination to Reduce Rated Power (except dynamic set point is not
matched)
PGN real active < Pmin. load parallel
Stopping the Last Engine Combination (load close to minimum load)
LDSS Dynamic
Dynamic characteristic = [(max. generator load min. generator load) * dynamic] + (min. generator load)
Dynamic power level = (dynamic characteristic) * (generator rated power)
Constants:
Low dynamic = 25 %
Moderate dynamic = 50 %
High dynamic = 75 %
Example for Moderate dynamic:
Dynamic characteristic = [(80 % 40 %) * 50 %] + (40 %) = 60 %
Dynamic power level = (60 %) * (200 kW) = 120 kW
Woodward
Page 333/339
Manual 37427
Appendix H.
Service Options
Product Service Options
The following factory options are available for servicing Woodward equipment, based on the standard
Woodward Product and Service Warranty (5-01-1205) that is in effect at the time the product is purchased from
Woodward or the service is performed. If you are experiencing problems with installation or unsatisfactory
performance of an installed system, the following options are available:
Consult the troubleshooting guide in the manual.
Contact Woodward technical assistance (see "How to Contact Woodward" later in this chapter) and discuss
your problem. In most cases, your problem can be resolved over the phone. If not, you can select which
course of action you wish to pursue based on the available services listed in this section.
Returning Equipment For Repair
If a control (or any part of an electronic control) is to be returned to Woodward for repair, please contact
Woodward in advance to obtain a Return Authorization Number. When shipping the unit(s), attach a tag with the
following information:
name and location where the control is installed;

name and phone number of contact person;
complete Woodward part numbers (P/N) and serial number (S/N);
description of the problem;
instructions describing the desired type of repair.
CAUTION
To prevent damage to electronic components caused by improper handling, read and observe the
precautions in Woodward manual 82715, Guide for Handling and Protection of Electronic Controls,
Printed Circuit Boards, and Modules.
Page 334/339
Woodward
Manual 37427
Packing A Control
Use the following materials when returning a complete control:
protective caps on any connectors;

antistatic protective bags on all electronic modules;
packing materials that will not damage the surface of the unit;
at least 100 mm (4 inches) of tightly packed, industry-approved packing material;
a packing carton with double walls;
a strong tape around the outside of the carton for increased strength.
Return Authorization Number RAN

When returning equipment to Woodward, please telephone and ask for the Customer Service Department in
Stuttgart [+49 (0) 711 789 54-0]. They will help expedite the processing of your order through our distributors or
local service facility. To expedite the repair process, contact Woodward in advance to obtain a Return
Authorization Number, and arrange for issue of a purchase order for the unit(s) to be repaired. No work can be
started until a purchase order is received.
NOTE
We highly recommend that you make arrangement in advance for return shipments. Contact a
Woodward customer service representative at +49 (0) 711 789 54-0 for instructions and for a
Return Authorization Number.
Replacement Parts
When ordering replacement parts for controls, include the following information:
the part numbers P/N (XXXX-XXX) that is on the enclosure nameplate;
the unit serial number S/N, which is also on the nameplate.
Woodward
Page 335/339
Manual 37427
How To Contact Woodward
Please contact following address if you have questions or if you want to send a product for repair:
Woodward GmbH
Handwerkstrasse 29
70565 Stuttgart - Germany
Phone:
Fax:
e-mail:
+49 (0) 711 789 54-0

+49 (0) 711 789 54-100
[email protected]
(8.00 - 16.30 German time)
For assistance outside Germany, call one of the following international Woodward facilities to obtain the address
and phone number of the facility nearest your location where you will be able to get information and service.
Facility
USA
India
Brazil
Japan
The Netherlands
Phone number
+1 (970) 482 5811
+91 (129) 409 7100
+55 (19) 3708 4800
+81 (476) 93 4661
+31 (23) 566 1111
You can also contact the Woodward Customer Service Department or consult our worldwide directory on
Woodwards website (www.woodward.com) for the name of your nearest Woodward distributor or service
facility. [For worldwide directory information, go to www.woodward.com/ic/locations.]
Page 336/339
Woodward
Manual 37427
Engineering Services
Woodward Industrial Controls Engineering Services offers the following after-sales support for Woodward
products. For these services, you can contact us by telephone, by e-mail, or through the Woodward website.
Technical support
Product training
Field service during commissioning
Technical Support is available through our many worldwide locations, through our authorized distributors, or
through GE Global Controls Services, depending on the product. This service can assist you with technical
questions or problem solving during normal business hours. Emergency assistance is also available during nonbusiness hours by phoning our toll-free number and stating the urgency of your problem. For technical
engineering support, please contact us via our toll-free or local phone numbers, e-mail us, or use our website and
reference technical support.
Product Training is available on-site from several of our worldwide facilities, at your location, or from GE
Global Controls Services, depending on the product. This training, conducted by experienced personnel, will
assure that you will be able to maintain system reliability and availability. For information concerning training,
please contact us via our toll-free or local phone numbers, e-mail us, or use our website and reference customer
training.
Field Service engineering on-site support is available, depending on the product and location, from our facility in
Colorado, or from one of many worldwide Woodward offices or authorized distributors. Field engineers are
experienced on both Woodward products as well as on much of the non-Woodward equipment with which our
products interface. For field service engineering assistance, please contact us via our toll-free or local phone
numbers, e-mail us, or use our website and reference field service.
Woodward
Page 337/339
Manual 37427
Technical Assistance
If you need to telephone for technical assistance, you will need to provide the following information. Please write
it down here before phoning:
Contact
Your company ____________________________________________________
Your name _______________________________________________________
Phone number ____________________________________________________
Fax number ______________________________________________________
Control (see name plate)
Unit no. and revision:
P/N: ____________________ REV: _____________
Unit type
easYgen- ___________________________________
Serial number
S/N _______________________________________
Description of your problem

________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
Please be sure you have a list of all parameters available. You can print this using ToolKit. Additionally you can
save the complete set of parameters (standard values) and send them to our Service department via e-mail.
Page 338/339
Woodward
We appreciate your comments about the content of our publications.

Please send comments to: [email protected]
Please include the manual number from the front cover of this publication.
Woodward GmbH
Handwerkstrasse 29 - 70565 Stuttgart - Germany
Phone +49 (0) 711 789 54-0 Fax +49 (0) 711 789 54-100
[email protected]
Homepage
http://www.woodward.com/power
Woodward has company-owned plants, subsidiaries, and branches, as well as authorized

distributors and other authorized service and sales facilities throughout the world.
Complete address/phone/fax/e-mail information
for all locations is available on our website (www.woodward.com).
2009/06/Stuttgart

EasyGen 2000 Configuration Manual 37427 PDF

Uploaded by

Copyright:

Available Formats

EasyGen 2000 Configuration Manual 37427 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EasyGen 2000 Configuration Manual 37427 PDF

Uploaded by

Copyright:

Available Formats

37427

Software Version 1.xxxx

easYgen-2000 Series - Genset Control

easYgen-2000 Series - Genset Control

CHAPTER 2. CONFIGURATION ................................................................................................ 13

Language-Dependent SID Files ...............................................................................................................17

Connect ToolKit and the easYgen Unit ......................................................................................... 18

easYgen-2000 Series - Genset Control

Configure Monitoring ............................................................................................................................. 47

Configure Monitoring: Generator, Operating Voltage / Frequency ........................................................... 48

Configure Monitoring: Mains ......................................................................................................... 83

Configure Monitoring: Mains, Operating Voltage / Frequency ................................................................. 83

Configure Monitoring: Engine ..................................................................................................... 100

Configure Monitoring: Engine, Overspeed (Levels 1 & 2) ANSI# 12 ...................................................... 100

Configure Monitoring: Breaker Monitoring .................................................................................. 114

Configure GCB....................................................................................................................................... 114

Configure Monitoring: Flexible Limits .......................................................................................... 120

Configure Monitoring: Miscellaneous, Alarm Acknowledgement ........................................................... 124

Configure Application........................................................................................................................... 138

Operation Of The Circuit Breakers ......................................................................................................... 140

easYgen-2000 Series - Genset Control

Configure Application: Configure Inputs and Outputs ................................................................. 156

Configure Analog Inputs (FlexIn) ............................................................................................................156

Configure Application: Configure Engine .................................................................................... 176

Configure Application: Configure Engine, Engine Type ..........................................................................176

Configure Application: Configure Emergency Run...................................................................... 189

Configure Application: Automatic, Start In AUTOMATIC Operating Mode (LogicsManager) .................191

Configure Application: Configure Controller ................................................................................ 215

Configure Interfaces ............................................................................................................................. 246

Configure CAN Interface 1 .....................................................................................................................246

Configure Interfaces: Configure RS-232 Interfaces .................................................................... 261

Configure Serial Interface 1 ....................................................................................................................261

Configure Interfaces: Configure RS-485 Interfaces .................................................................... 262

Configure Serial Interface 2 ....................................................................................................................262

Configure LogicsManager .................................................................................................................... 263

LogicsManager: Daily Time Set Point ....................................................................................................264

Configure Counters .............................................................................................................................. 266

APPENDIX A. MISCELLANEOUS ............................................................................................ 269

Alarm Classes ...................................................................................................................................... 269

easYgen-2000 Series - Genset Control

APPENDIX B. LOGICSMANAGER ........................................................................................... 271

Structure and Description of the LogicsManager ................................................................................... 271

Logical Symbols ................................................................................................................................... 272

APPENDIX C. ANALOG MANAGER ......................................................................................... 305

Data Sources ....................................................................................................................................... 305

easYgen-2000 Series - Genset Control

APPENDIX D. EVENT HISTORY .............................................................................................. 318

Resetting the Event History Using the Front Panel ................................................................................318

APPENDIX E. TRIGGERING CHARACTERISTICS....................................................................... 321

Time-Dependent Overshoot Monitoring ............................................................................................... 321

APPENDIX F. CHARACTERISTICS OF THE VDO INPUTS .......................................................... 327

VDO Input "Pressure" (0 to 5 bar / 0 to 72 psi) - Index "III" ................................................................. 327

APPENDIX G. LDSS FORMULAS ........................................................................................... 332

Abbreviations ....................................................................................................................................... 332

Changing the Engine Combination to Increase Rated Power.................................................................332

Mains Parallel Operation (Import/Export Control) ....................................................................... 332

LDSS Mode Generator Load................................................................................................................ 333

Changing the Engine Combination to Increase Rated Power.................................................................333

Mains Parallel Operation (Import/Export Control) ....................................................................... 333